* elf64-ppc.c (ppc64_elf_size_stubs): Round up glink_eh_frame
size to output section alignment.
(ppc64_elf_build_stubs): Likewise, and extend last FDE to cover.
(read_uleb128_to_uint64): Renamed from read_uleb128_to_ull.
Change to take a uint64_t * argument instead of unsigned long long.
(read_sleb128_to_uint64): Renamed from read_sleb128_to_ll.
Change to take an int64_t * argument instead of long long.
* layout.cc (Layout::section_name_mapping): Add rules to handle
exact match on .data.rel.ro.local or .data.rel.ro.
(Layout::output_section_name): Check for exact matches.
"const gdb_byte *".
(struct dwarf2_fde): Make instructions, end "const gdb_byte *".
(execute_cfa_program): Update to match API of leb128 functions.
(read_1_byte, read_4_bytes, read_8_bytes): Make buf parameter
"const gdb_byte *".
(read_unsigned_leb128, read_signed_leb128): Delete.
(read_initial_length): Change type of buf argument to
"const gdb_byte *".
(read_encoded_value): Update to match API of leb128 functions.
(decode_frame_entry): Change result to "const gdb_byte *", and
similarly for "start" parameter.
(decode_frame_entry_1): Ditto. Use new leb128 reader functions.
(dwarf2_build_frame_info): Change local frame_ptr to
"const gdb_byte *".
* dwarf2expr.c (safe_read_uleb128, safe_read_sleb128): Replaces
read_uleb128, read_sleb128. All callers updated.
(safe_skip_leb128): New function.
(dwarf_block_to_dwarf_reg): Update to match API of leb128 functions.
Call gdb_read_uleb128, gdb_skip_leb128 instead of read_uleb128.
(dwarf_block_to_dwarf_reg_deref): Update to match API of leb128
functions. Call gdb_read_uleb128, gdb_read_sleb128 instead of
read_uleb128, read_sleb128.
(dwarf_block_to_fb_offset, dwarf_block_to_sp_offset): Ditto.
(execute_stack_op): Update to match API of leb128 functions.
* dwarf2expr.h: #include "leb128.h".
(read_uleb128, read_sleb128): Delete.
(gdb_read_uleb128, gdb_read_sleb128, gdb_skip_leb128): New functions.
(safe_read_uleb128, safe_read_sleb128, safe_skip_leb128): Declare.
* dwarf2loc.c (debug_loc_kind): New enum.
(decode_debug_loc_addresses): New function.
(decode_debug_loc_dwo_addresses): New function.
(dwarf2_find_location_expression): Rewrite.
(dwarf2_compile_expr_to_ax): Update to match API of leb128 functions.
(locexpr_describe_location_piece): Ditto.
(disassemble_dwarf_expression): Ditto.
(locexpr_describe_location_1): Ditto.
(loclist_describe_location): Rewrite.
* dwarf2loc.h (dwarf2_loclist_baton): New member "from_dwo".
* dwarf2read.c (die_reader_specs): New member "buffer_end".
(dwarf2_section_buffer_overflow_complaint): Renamed from
dwarf2_macros_too_long_complaint. All callers updated.
(skip_leb128): Delete.
(init_cu_die_reader): Initialize reader->buffer_end.
(skip_one_die): Replace call to skip_leb128 with safe_skip_leb128.
(skip_form_bytes): New arg buffer_end. All callers updated.
Replace call to skip_leb128 with gdb_skip_leb128.
(skip_unknown_opcode): New arg mac_end. All callers updated.
(fill_in_loclist_baton): Initialize baton->from_dwo.
* ld-x86-64/pr12570a.d (name): Distinguish it from pr12570b.d case.
Loosen CFI-matching regexp so it matches x86_64-*-nacl* variant too.
* ld-x86-64/pr12570b.d: Likewise.
* ld-x86-64/x86-64.exp: Revert last change.
first one is zero size or discarded.
* elf32-ppc.c (ppc_elf_size_dynamic_sections): Set most of
glink_eh_frame contents here..
(ppc_elf_finish_dynamic_sections): ..rather than here. Just set
offset to .glink.
* linux-low (__UCLIBC__ && !(__UCLIBC_HAS_MMU__ || __ARCH_HAS_MMU__)):
Include asm/ptrace.h.
(PT_TEXT_ADDR, PT_DATA_ADDR, PT_TEXT_END_ADDR): Define only if not
already defined.
If you configure gas for a mips32el-* target, the default cpu calculation
gets mangled, and we end up passing and invalid value as the default cpu.
If you try executing gas after that, it segfaults. This is because it
assumes that the default cpu value is always valid.
$ ./gas/as-new
Assembler messages:
Error: Bad value (2) for default CPU
Segmentation fault (core dumped)
I'm not debating that the target tuple is valid, just that gas shouldn't
crash. So add a friendly assert to avoid that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* NEWS (--with-auto-load-dir): Prepend $debugdir to the default path.
Describe it.
* auto-load.c (auto_load_expand_dir_vars): New function.
(auto_load_safe_path_vec_update): Use it, remove the
substitute_path_component call thanks to it.
(auto_load_objfile_script): Remove the debug_file_directory processing.
Use auto_load_expand_dir_vars, remove the substitute_path_component
call thanks to it.
* configure: Regenerate.
* configure.ac (--with-auto-load-dir): Prepend $debugdir to the default
path. Escape $ also for $debugdir.
(--with_auto_load_safe_path): Escape $ also for $debugdir.
* utils.c (substitute_path_component): Accept also DIRNAME_SEPARATOR.
gdb/doc/
* gdb.texinfo (Separate Debug Files): New anchor debug-file-directory.
Mention also --with-separate-debug-dir.
(Auto-loading): Prepend $debugdir in the sample output.
(Auto-loading safe path): Likewise. Mention also $debugdir for the
auto-load safe-path variable.
(objfile-gdb.py file): Remove the extra debug-file-directory paragraph.
Mention also $debugdir for 'set auto-load scripts-directory'.
Alan Modra