* m32r-tdep.c: Improved frame_chain and fn prologue analysis.
* configure.tgt: Add entry for m32r target.
* monitor.h: Add a flag to tell monitor_store_register to use
(val, regno) instead of (regno, val).
* monitor.c: Make monitor_store_register honor the above flag.
Make monitor_exp ignore DC1/DC3 for m32r.
Increase buf size in monitor_dump_regs.
* monitor.h,monitor.c:
Added monitor flags MO_NO_ECHO_ON_SETMEM (don't expect echo on
setmem command), MO_RUN_FIRST_TIME (if command to start process
running on target is different from one to continue execution),
MO_HEX_PREFIX (if addresses from monitor have a "0x" prefix).
* monitor.c,parse.c,sparc-tdep.c:
Don't require strings in the registers array. This is to allow
NULLs to be place holders in the tm-*.h file so that only minor
changes are needed when a new processor is introduced (eg, one
without floating point).
* sparc-tdep.c: Conditionally remove dependancies on floating point.
* sparclet-rom.c,config/sparc/sparclet.mt,config/sparc/tm-sparclet.h:
New files for target sparclet.
* symfile.c: Add option for 2nd parameter on load command : a load
offset added to the vma of each section.
with the obvious extension. (monitor_read_memory_single): Use
regexp for getmem.resp_delim because of parsing ambiguities caused
by certain monitors. (monitor_read_memory): Use new regexp stuff
to parse getmem.resp_delim.
* sh3-rom.c: Finish off table. Use new regexp capability for
getmem commands.
* monitor.c: Turn on caching.
(monitor_printf): If a ^C was sent, don't expect to see its
echo.
(monitor_open): Enable caching.
(monitor_resume, monitor_load): Flush cache.
(monitor_xfer_memory): Call cache routine.
(monitor_dump_regs): New.
(monitor_fetch_registers): If monitor_dump_regs available
then use it.
(monitor_load): Don't ref exec_bfd if it's NULL.
(monitor_load_srec): Use new monitor_make_srec calling convention.
(monitor_make_srec): Rewrite to cope with two, three and four byte
addresses.
* remote-hms.c (hms_cmds): Initialze end-of-command delim.
* dcache.h, dcache.h: Rewritten.
* remote.c: Reenable caching.
(getpkt): Reduce MAX_TRIES to 3.
(remote_xfer_memory): Use dcache_xfer_memory.
* defs.h (error_hook): New.
* top.c (error_hook): New definition.
* utils.c (error): Use error_hook if initialized.
* sparcl-tdep.c (HAVE_SOCKETS): Don't define if GO32 or WIN32. Use
HAVE_SOCKETS in place of #ifndef GO32.
error message to work with pre-ansi compilers.
(monitor_load_srec): reduced length of s-records from 128 to 32
bytes so download is more reliable with the rom68k monitor.
* rom68k-rom.c: Added trailing space to prompt string.
* config/i386/xm-i386sco.h (HAVE_STRSTR): Removed.
* config/i386/xm-go32.h, mswin/xm.h (SYS_SIGLIST_MISSING):
Removed.
* defs.h, config/{xm-lynx.h, xm-nbsd.h},
config/i386/{xm-i386bsd.h, xm-linux.h},
config/m68k/xm-hp300bsd.h, config/mips/xm-irix4.h,
config/ns32k/xm-ns32km3.h, doc/gdbint.texinfo
(PSIGNAL_IN_SIGNAL_H): Removed.
* Makefile.in (gdbtk.o): Use X11_CFLAGS to provide alternate
locations (per-host) for X11 include files.
* config/pa/hppahpux.mh (XM_CLIBS): Add -L/usr/lib/X11R5 to force
the use of R5 libs. (X11_CFLAGS): Add this to indicate the locs
of the R5 include files.
end-sanitize-gdbtk
* monitor.c monitor.h remote-est.c rom68k-rom.c: Add start of
support for interrupting target.
* monitor.c (monitor_open): Send stop command before doing
anything else.
* (monitor_load_srec): Fix record size calculation to prevent end
of segment from getting trashed.
* rom68k-rom.c: Update to latest version of struct monitor_ops.
* config/sparc/tm-sparc.h (FIX_CALL_DUMMY): Fix byte-order
problems. Makes DOS hosted function calling work.
* sparclite/crt0.s: Define _start to make COFF happy.
* testsuite/config/rom68k.exp (gdb_target_rom68k): Use
$targetname, $serialport and $baud instead of hardwired variables.
* testsuite/gdb.base/{sigall.exp signals.exp}: Skip these if the
target doesn't support signals.
Sun make (with VPATH) work...
* monitor.c monitor.h rom68k-rom.c: Serious cleanup to make IDP
(rom68k) target work right.
* array-rom.c op50-rom.c w89k-rom.c: Partial updates to new
monitor.c interface. More work needs to be done here.
* config/m68k/tm-monitor.h: Change DECR_PC_AFTER_BREAK to 0 to
match the IDP monitor. Also, set NUM_REGS to 18 cuz there's no
floating-point for this card.
to monitor config structure for supported baud rates for a target
and variable stop bits.
* monitor.c (monitor_fetch_register): Store register values in big
endian format on any host.
* monitor.c (monitor_load): check the load type and load the file
accordingly. Default to gr_load_image().
* monitor.c (monitor_load_ascii_srec): Load an ascii file in
srecord format by downloading to the monitor.
* w89k-rom.c, op50n-rom.c: set supported load types.
David Edelsohn
Michael Meissner
Michael Snyder
Dawn Perchik
Stan Shebs
Stu Grossman
Jeff Law
J.T. Conklin
Steve Chamberlain
Kung Hsu
Rob Savoye