540 lines
19 KiB
Plaintext
540 lines
19 KiB
Plaintext
_dnl__ -*- Texinfo -*-
|
|
_dnl__ Copyright (c) 1990 1991 1992 Free Software Foundation, Inc.
|
|
_dnl__ This file is part of the source for the GDB manual.
|
|
_dnl__ M4 FRAGMENT $Id$
|
|
_dnl__ This text diverted to "Remote Debugging" section in general case;
|
|
_dnl__ however, if we're doing a manual specifically for one of these, it
|
|
_dnl__ belongs up front (in "Getting In and Out" chapter).
|
|
_if__(_I960__)
|
|
_if__(!_GENERIC__)
|
|
@node i960-Nindy Remote, EB29K Remote, Mode Options, Starting _GDBN__
|
|
_fi__(!_GENERIC__)
|
|
_if__(_GENERIC__)
|
|
@node i960-Nindy Remote, EB29K Remote, Remote, Remote
|
|
_fi__(_GENERIC__)
|
|
@subsection _GDBN__ with a Remote i960 (Nindy)
|
|
|
|
@cindex Nindy
|
|
@cindex i960
|
|
@dfn{Nindy} is a ROM Monitor program for Intel 960 target systems. When
|
|
_GDBN__ is configured to control a remote Intel 960 using Nindy, you can
|
|
tell _GDBN__ how to connect to the 960 in several ways:
|
|
|
|
@itemize @bullet
|
|
@item
|
|
Through command line options specifying serial port, version of the
|
|
Nindy protocol, and communications speed;
|
|
|
|
@item
|
|
By responding to a prompt on startup;
|
|
|
|
@item
|
|
By using the @code{target} command at any point during your _GDBN__
|
|
session. @xref{Target Commands, ,Commands for Managing Targets}.
|
|
|
|
@end itemize
|
|
|
|
@menu
|
|
* Nindy Startup:: Startup with Nindy
|
|
* Nindy Options:: Options for Nindy
|
|
* Nindy reset:: Nindy Reset Command
|
|
@end menu
|
|
|
|
@node Nindy Startup, Nindy Options, i960-Nindy Remote, i960-Nindy Remote
|
|
@subsubsection Startup with Nindy
|
|
|
|
If you simply start @code{_GDBP__} without using any command-line
|
|
options, you are prompted for what serial port to use, @emph{before} you
|
|
reach the ordinary _GDBN__ prompt:
|
|
|
|
@example
|
|
Attach /dev/ttyNN -- specify NN, or "quit" to quit:
|
|
@end example
|
|
|
|
@noindent
|
|
Respond to the prompt with whatever suffix (after @samp{/dev/tty})
|
|
identifies the serial port you want to use. You can, if you choose,
|
|
simply start up with no Nindy connection by responding to the prompt
|
|
with an empty line. If you do this, and later wish to attach to Nindy,
|
|
use @code{target} (@pxref{Target Commands, ,Commands for Managing Targets}).
|
|
|
|
@node Nindy Options, Nindy reset, Nindy Startup, i960-Nindy Remote
|
|
@subsubsection Options for Nindy
|
|
|
|
These are the startup options for beginning your _GDBN__ session with a
|
|
Nindy-960 board attached:
|
|
|
|
@table @code
|
|
@item -r @var{port}
|
|
Specify the serial port name of a serial interface to be used to connect
|
|
to the target system. This option is only available when _GDBN__ is
|
|
configured for the Intel 960 target architecture. You may specify
|
|
@var{port} as any of: a full pathname (e.g. @samp{-r /dev/ttya}), a
|
|
device name in @file{/dev} (e.g. @samp{-r ttya}), or simply the unique
|
|
suffix for a specific @code{tty} (e.g. @samp{-r a}).
|
|
|
|
@item -O
|
|
(An uppercase letter ``O'', not a zero.) Specify that _GDBN__ should use
|
|
the ``old'' Nindy monitor protocol to connect to the target system.
|
|
This option is only available when _GDBN__ is configured for the Intel 960
|
|
target architecture.
|
|
|
|
@quotation
|
|
@emph{Warning:} if you specify @samp{-O}, but are actually trying to
|
|
connect to a target system that expects the newer protocol, the connection
|
|
will fail, appearing to be a speed mismatch. _GDBN__ will repeatedly
|
|
attempt to reconnect at several different line speeds. You can abort
|
|
this process with an interrupt.
|
|
@end quotation
|
|
|
|
@item -brk
|
|
Specify that _GDBN__ should first send a @code{BREAK} signal to the target
|
|
system, in an attempt to reset it, before connecting to a Nindy target.
|
|
|
|
@quotation
|
|
@emph{Warning:} Many target systems do not have the hardware that this
|
|
requires; it only works with a few boards.
|
|
@end quotation
|
|
@end table
|
|
|
|
The standard @samp{-b} option controls the line speed used on the serial
|
|
port.
|
|
|
|
@c @group
|
|
@node Nindy reset, , Nindy Options, i960-Nindy Remote
|
|
@subsubsection Nindy Reset Command
|
|
|
|
@table @code
|
|
@item reset
|
|
@kindex reset
|
|
For a Nindy target, this command sends a ``break'' to the remote target
|
|
system; this is only useful if the target has been equipped with a
|
|
circuit to perform a hard reset (or some other interesting action) when
|
|
a break is detected.
|
|
@end table
|
|
@c @end group
|
|
_fi__(_I960__)
|
|
|
|
_if__(_AMD29K__)
|
|
_if__(!_GENERIC__)
|
|
@node EB29K Remote, VxWorks Remote, i960-Nindy Remote, Starting _GDBN__
|
|
_fi__(!_GENERIC__)
|
|
_if__(_GENERIC__)
|
|
@node EB29K Remote, VxWorks Remote, i960-Nindy Remote, Remote
|
|
_fi__(_GENERIC__)
|
|
@subsection _GDBN__ with a Remote EB29K
|
|
|
|
@cindex EB29K board
|
|
@cindex running 29K programs
|
|
|
|
To use _GDBN__ from a Unix system to run programs on AMD's EB29K
|
|
board in a PC, you must first connect a serial cable between the PC
|
|
and a serial port on the Unix system. In the following, we assume
|
|
you've hooked the cable between the PC's @file{COM1} port and
|
|
@file{/dev/ttya} on the Unix system.
|
|
|
|
@menu
|
|
* Comms (EB29K):: Communications Setup
|
|
* _GDBP__-EB29K:: EB29K cross-debugging
|
|
* Remote Log:: Remote Log
|
|
@end menu
|
|
|
|
@node Comms (EB29K), _GDBP__-EB29K, EB29K Remote, EB29K Remote
|
|
@subsubsection Communications Setup
|
|
|
|
The next step is to set up the PC's port, by doing something like the
|
|
following in DOS on the PC:
|
|
|
|
_0__@example
|
|
C:\> MODE com1:9600,n,8,1,none
|
|
_1__@end example
|
|
|
|
@noindent
|
|
This example---run on an MS DOS 4.0 system---sets the PC port to 9600
|
|
bps, no parity, eight data bits, one stop bit, and no ``retry'' action;
|
|
you must match the communications parameters when establishing the Unix
|
|
end of the connection as well.
|
|
@c FIXME: Who knows what this "no retry action" crud from the DOS manual may
|
|
@c mean? It's optional; leave it out? ---pesch@cygnus.com, 25feb91
|
|
|
|
To give control of the PC to the Unix side of the serial line, type
|
|
the following at the DOS console:
|
|
|
|
_0__@example
|
|
C:\> CTTY com1
|
|
_1__@end example
|
|
|
|
@noindent
|
|
(Later, if you wish to return control to the DOS console, you can use
|
|
the command @code{CTTY con}---but you must send it over the device that
|
|
had control, in our example over the @file{COM1} serial line).
|
|
|
|
From the Unix host, use a communications program such as @code{tip} or
|
|
@code{cu} to communicate with the PC; for example,
|
|
|
|
@example
|
|
cu -s 9600 -l /dev/ttya
|
|
@end example
|
|
|
|
@noindent
|
|
The @code{cu} options shown specify, respectively, the linespeed and the
|
|
serial port to use. If you use @code{tip} instead, your command line
|
|
may look something like the following:
|
|
|
|
@example
|
|
tip -9600 /dev/ttya
|
|
@end example
|
|
|
|
@noindent
|
|
Your system may define a different name where our example uses
|
|
@file{/dev/ttya} as the argument to @code{tip}. The communications
|
|
parameters, including which port to use, are associated with the
|
|
@code{tip} argument in the ``remote'' descriptions file---normally the
|
|
system table @file{/etc/remote}.
|
|
@c FIXME: What if anything needs doing to match the "n,8,1,none" part of
|
|
@c the DOS side's comms setup? cu can support -o (odd
|
|
@c parity), -e (even parity)---apparently no settings for no parity or
|
|
@c for character size. Taken from stty maybe...? John points out tip
|
|
@c can set these as internal variables, eg ~s parity=none; man stty
|
|
@c suggests that it *might* work to stty these options with stdin or
|
|
@c stdout redirected... ---pesch@cygnus.com, 25feb91
|
|
|
|
@kindex EBMON
|
|
Using the @code{tip} or @code{cu} connection, change the DOS working
|
|
directory to the directory containing a copy of your 29K program, then
|
|
start the PC program @code{EBMON} (an EB29K control program supplied
|
|
with your board by AMD). You should see an initial display from
|
|
@code{EBMON} similar to the one that follows, ending with the
|
|
@code{EBMON} prompt @samp{#}---
|
|
|
|
_0__@example
|
|
C:\> G:
|
|
|
|
G:\> CD \usr\joe\work29k
|
|
|
|
G:\USR\JOE\WORK29K> EBMON
|
|
Am29000 PC Coprocessor Board Monitor, version 3.0-18
|
|
Copyright 1990 Advanced Micro Devices, Inc.
|
|
Written by Gibbons and Associates, Inc.
|
|
|
|
Enter '?' or 'H' for help
|
|
|
|
PC Coprocessor Type = EB29K
|
|
I/O Base = 0x208
|
|
Memory Base = 0xd0000
|
|
|
|
Data Memory Size = 2048KB
|
|
Available I-RAM Range = 0x8000 to 0x1fffff
|
|
Available D-RAM Range = 0x80002000 to 0x801fffff
|
|
|
|
PageSize = 0x400
|
|
Register Stack Size = 0x800
|
|
Memory Stack Size = 0x1800
|
|
|
|
CPU PRL = 0x3
|
|
Am29027 Available = No
|
|
Byte Write Available = Yes
|
|
|
|
# ~.
|
|
_1__@end example
|
|
|
|
Then exit the @code{cu} or @code{tip} program (done in the example by
|
|
typing @code{~.} at the @code{EBMON} prompt). @code{EBMON} will keep
|
|
running, ready for _GDBN__ to take over.
|
|
|
|
For this example, we've assumed what is probably the most convenient
|
|
way to make sure the same 29K program is on both the PC and the Unix
|
|
system: a PC/NFS connection that establishes ``drive @code{G:}'' on the
|
|
PC as a file system on the Unix host. If you do not have PC/NFS or
|
|
something similar connecting the two systems, you must arrange some
|
|
other way---perhaps floppy-disk transfer---of getting the 29K program
|
|
from the Unix system to the PC; _GDBN__ will @emph{not} download it over the
|
|
serial line.
|
|
|
|
@node _GDBP__-EB29K, Remote Log, Comms (EB29K), EB29K Remote
|
|
@subsubsection EB29K cross-debugging
|
|
|
|
Finally, @code{cd} to the directory containing an image of your 29K
|
|
program on the Unix system, and start _GDBN__---specifying as argument the
|
|
name of your 29K program:
|
|
|
|
@example
|
|
cd /usr/joe/work29k
|
|
_GDBP__ myfoo
|
|
@end example
|
|
|
|
Now you can use the @code{target} command:
|
|
|
|
@example
|
|
target amd-eb /dev/ttya 9600 MYFOO
|
|
@c FIXME: test above 'target amd-eb' as spelled, with caps! caps are meant to
|
|
@c emphasize that this is the name as seen by DOS (since I think DOS is
|
|
@c single-minded about case of letters). ---pesch@cygnus.com, 25feb91
|
|
@end example
|
|
|
|
@noindent
|
|
In this example, we've assumed your program is in a file called
|
|
@file{myfoo}. Note that the filename given as the last argument to
|
|
@code{target amd-eb} should be the name of the program as it appears to DOS.
|
|
In our example this is simply @code{MYFOO}, but in general it can include
|
|
a DOS path, and depending on your transfer mechanism may not resemble
|
|
the name on the Unix side.
|
|
|
|
At this point, you can set any breakpoints you wish; when you are ready
|
|
to see your program run on the 29K board, use the _GDBN__ command
|
|
@code{run}.
|
|
|
|
To stop debugging the remote program, use the _GDBN__ @code{detach}
|
|
command.
|
|
|
|
To return control of the PC to its console, use @code{tip} or @code{cu}
|
|
once again, after your _GDBN__ session has concluded, to attach to
|
|
@code{EBMON}. You can then type the command @code{q} to shut down
|
|
@code{EBMON}, returning control to the DOS command-line interpreter.
|
|
Type @code{CTTY con} to return command input to the main DOS console,
|
|
and type @kbd{~.} to leave @code{tip} or @code{cu}.
|
|
|
|
@node Remote Log, , _GDBP__-EB29K, EB29K Remote
|
|
@subsubsection Remote Log
|
|
@kindex eb.log
|
|
@cindex log file for EB29K
|
|
|
|
The @code{target amd-eb} command creates a file @file{eb.log} in the
|
|
current working directory, to help debug problems with the connection.
|
|
@file{eb.log} records all the output from @code{EBMON}, including echoes
|
|
of the commands sent to it. Running @samp{tail -f} on this file in
|
|
another window often helps to understand trouble with @code{EBMON}, or
|
|
unexpected events on the PC side of the connection.
|
|
_fi__(_AMD29K__)
|
|
|
|
_if__(_VXWORKS__)
|
|
_if__(!_GENERIC__)
|
|
@node VxWorks Remote, , EB29K Remote, Starting _GDBN__
|
|
_fi__(!_GENERIC__)
|
|
_if__(_GENERIC__)
|
|
@node VxWorks Remote, , EB29K Remote, Remote
|
|
_fi__(_GENERIC__)
|
|
@subsection _GDBN__ and VxWorks
|
|
@cindex VxWorks
|
|
|
|
_GDBN__ enables developers to spawn and debug tasks running on networked
|
|
VxWorks targets from a Unix host. Already-running tasks spawned from
|
|
the VxWorks shell can also be debugged. _GDBN__ uses code that runs on
|
|
both the UNIX host and on the VxWorks target. The program
|
|
@code{_GDBP__} is installed and executed on the UNIX host.
|
|
|
|
The following information on connecting to VxWorks was current when
|
|
this manual was produced; newer releases of VxWorks may use revised
|
|
procedures.
|
|
|
|
The remote debugging interface (RDB) routines are installed and executed
|
|
on the VxWorks target. These routines are included in the VxWorks library
|
|
@file{rdb.a} and are incorporated into the system image when source-level
|
|
debugging is enabled in the VxWorks configuration.
|
|
|
|
@kindex INCLUDE_RDB
|
|
If you wish, you can define @code{INCLUDE_RDB} in the VxWorks
|
|
configuration file @file{configAll.h} to include the RDB interface
|
|
routines and spawn the source debugging task @code{tRdbTask} when
|
|
VxWorks is booted. For more information on configuring and remaking
|
|
_if__(_FSF__)
|
|
VxWorks, see the manufacturer's manual.
|
|
_fi__(_FSF__)
|
|
_if__(!_FSF__)
|
|
VxWorks, see the @cite{VxWorks Programmer's Guide}.
|
|
_fi__(!_FSF__)
|
|
|
|
Once you have included the RDB interface in your VxWorks system image
|
|
and set your Unix execution search path to find _GDBN__, you are ready
|
|
to run _GDBN__. From your UNIX host, type:
|
|
|
|
@smallexample
|
|
% _GDBP__
|
|
@end smallexample
|
|
|
|
_GDBN__ will come up showing the prompt:
|
|
|
|
@smallexample
|
|
(_GDBP__)
|
|
@end smallexample
|
|
|
|
@menu
|
|
* VxWorks connection:: Connecting to VxWorks
|
|
* VxWorks download:: VxWorks Download
|
|
* VxWorks attach:: Running Tasks
|
|
@end menu
|
|
|
|
@node VxWorks connection, VxWorks download, VxWorks Remote, VxWorks Remote
|
|
@subsubsection Connecting to VxWorks
|
|
|
|
The _GDBN__ command @code{target} lets you connect to a VxWorks target on the
|
|
network. To connect to a target whose host name is ``@code{tt}'', type:
|
|
|
|
@smallexample
|
|
(_GDBP__) target vxworks tt
|
|
@end smallexample
|
|
|
|
_GDBN__ will display a message similar to the following:
|
|
|
|
@smallexample
|
|
Attaching remote machine across net... Success!
|
|
@end smallexample
|
|
|
|
_GDBN__ will then attempt to read the symbol tables of any object modules
|
|
loaded into the VxWorks target since it was last booted. _GDBN__ locates
|
|
these files by searching the directories listed in the command search
|
|
path (@pxref{Environment, ,Your Program's Environment}); if it fails
|
|
to find an object file, it will display a message such as:
|
|
|
|
@smallexample
|
|
prog.o: No such file or directory.
|
|
@end smallexample
|
|
|
|
This will cause the @code{target} command to abort. When this happens,
|
|
you should add the appropriate directory to the search path, with the
|
|
_GDBN__ command @code{path}, and execute the @code{target} command
|
|
again.
|
|
|
|
@node VxWorks download, VxWorks attach, VxWorks connection, VxWorks Remote
|
|
@subsubsection VxWorks Download
|
|
|
|
@cindex download to VxWorks
|
|
If you have connected to the VxWorks target and you want to debug an
|
|
object that has not yet been loaded, you can use the _GDBN__ @code{load}
|
|
command to download a file from UNIX to VxWorks incrementally. The
|
|
object file given as an argument to the @code{load} command is actually
|
|
opened twice: first by the VxWorks target in order to download the code,
|
|
then by _GDBN__ in order to read the symbol table. This can lead to
|
|
problems if the current working directories on the two systems differ.
|
|
It is simplest to set the working directory on both systems to the
|
|
directory in which the object file resides, and then to reference the
|
|
file by its name, without any path. Thus, to load a program
|
|
@file{prog.o}, residing in @file{wherever/vw/demo/rdb}, on VxWorks type:
|
|
|
|
@smallexample
|
|
-> cd "wherever/vw/demo/rdb"
|
|
@end smallexample
|
|
|
|
On _GDBN__ type:
|
|
|
|
@smallexample
|
|
(_GDBP__) cd wherever/vw/demo/rdb
|
|
(_GDBP__) load prog.o
|
|
@end smallexample
|
|
|
|
_GDBN__ will display a response similar to the following:
|
|
|
|
@smallexample
|
|
Reading symbol data from wherever/vw/demo/rdb/prog.o... done.
|
|
@end smallexample
|
|
|
|
You can also use the @code{load} command to reload an object module
|
|
after editing and recompiling the corresponding source file. Note that
|
|
this will cause _GDBN__ to delete all currently-defined breakpoints,
|
|
auto-displays, and convenience variables, and to clear the value
|
|
history. (This is necessary in order to preserve the integrity of
|
|
debugger data structures that reference the target system's symbol
|
|
table.)
|
|
|
|
@node VxWorks attach, , VxWorks download, VxWorks Remote
|
|
@subsubsection Running Tasks
|
|
|
|
@cindex running VxWorks tasks
|
|
You can also attach to an existing task using the @code{attach} command as
|
|
follows:
|
|
|
|
@smallexample
|
|
(_GDBP__) attach @var{task}
|
|
@end smallexample
|
|
|
|
@noindent
|
|
where @var{task} is the VxWorks hexadecimal task ID. The task can be running
|
|
or suspended when you attach to it. If running, it will be suspended at
|
|
the time of attachment.
|
|
_fi__(_VXWORKS__)
|
|
_if__(_H8__)
|
|
_if__(!_GENERIC__)
|
|
@node Hitachi H8/300 Remote, , VxWorks Remote, Starting _GDBN__
|
|
_fi__(!_GENERIC__)
|
|
_if__(_GENERIC__)
|
|
@node Hitachi H8/300 Remote, , VxWorks Remote, Remote
|
|
_fi__(_GENERIC__)
|
|
@subsection _GDBN__ and the Hitachi H8/300
|
|
_GDBN__ needs to know three things to talk to your H8/300:
|
|
|
|
@enumerate
|
|
@item
|
|
that you want to use @samp{target hms}, the remote debugging
|
|
interface for the H8/300 (this is the default for @code{gdb83}, the
|
|
version of GDB configured specifically for the H8/300);
|
|
|
|
@item
|
|
what serial device connects your host to your H8/300 (the first serial
|
|
device available on your host is the default);
|
|
|
|
@item
|
|
what speed to use over the serial device.
|
|
@end enumerate
|
|
|
|
@kindex device
|
|
@cindex serial device for H8/300
|
|
Use the special @code{gdb83} command @samp{device @var{port}} if you need to
|
|
explicitly set the serial device. The default @var{port} is the first
|
|
available port on your host; on Unix hosts, this is typically something
|
|
like @file{/dev/ttya}, and on DOS hosts @file{com1}.
|
|
|
|
@kindex speed
|
|
@cindex serial line speed for H8/300
|
|
@code{gdb83} has another special command to set the communications speed
|
|
for the H8/300: @samp{speed @var{bps}}.
|
|
|
|
For example, you might start an H8/300 debugging session at 19200 bps
|
|
like this (exploiting the default target and device):
|
|
|
|
@smallexample
|
|
$ gdb83
|
|
@c FIXME: this falsifies the exact text played out, to permit smallbook
|
|
@c FIXME... format to come out better.
|
|
GDB is free software and you are welcome to distribute copies
|
|
of it under certain conditions; type "show copying" to see
|
|
the conditions.
|
|
There is absolutely no warranty for GDB; type "show warranty" for details.
|
|
GDB _GDB_VN__, Copyright 1992 Free Software Foundation, Inc.
|
|
(gdb83) speed 19200
|
|
Remote debugging on an H8/300 HMS via /dev/ttya.
|
|
Checking target is in sync
|
|
Sending commands to set target to 19200
|
|
(gdb83)
|
|
@end smallexample
|
|
|
|
@noindent
|
|
To download your program and make it the current _GDBN__ target, use the
|
|
@code{load} command:
|
|
|
|
@example
|
|
(gdb83) load smain
|
|
.text: 8000 .. 9d92 ****
|
|
.data: 9d92 .. 9e34 *
|
|
(gdb83)
|
|
@end example
|
|
|
|
@noindent
|
|
While downloading the program (@samp{smain} in this example), _GDBN__
|
|
displays the names of the program's sections, and a @samp{*} for each 2K
|
|
of data downloaded. (If you want to refresh _GDBN__ data on symbols or
|
|
on the executable file without downloading, use the _GDBN__ commands
|
|
@code{file} or @code{symbol-file}. These commands, and @code{load}
|
|
itself, are described in @ref{Files,,Commands to Specify Files}.)
|
|
|
|
All the standard _GDBN__ facilities are at your disposal for controlling
|
|
the program on the H8/300; you can start the program with @code{run},
|
|
set breakpoints with @code{break}, display data with @code{print} or
|
|
@code{x}, and so on.
|
|
|
|
Remember, however, that @emph{operating system} facilities aren't
|
|
available on your H8/300; for example, if your program hangs, you can't
|
|
send an interrupt---but you can press the @sc{reset} switch! _GDBN__
|
|
will see the effect of a @sc{reset} on the H8/300 board as a ``normal
|
|
exit'' of your program.
|
|
_fi__(_H8__)
|