linux/drivers/usb/musb/blackfin.c

323 lines
7.3 KiB
C
Raw Normal View History

/*
* MUSB OTG controller driver for Blackfin Processors
*
* Copyright 2006-2008 Analog Devices Inc.
*
* Enter bugs at http://blackfin.uclinux.org/
*
* Licensed under the GPL-2 or later.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/init.h>
#include <linux/list.h>
#include <linux/gpio.h>
#include <linux/io.h>
#include <asm/cacheflush.h>
#include "musb_core.h"
#include "blackfin.h"
/*
* Load an endpoint's FIFO
*/
void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src)
{
void __iomem *fifo = hw_ep->fifo;
void __iomem *epio = hw_ep->regs;
prefetch((u8 *)src);
musb_writew(epio, MUSB_TXCOUNT, len);
DBG(4, "TX ep%d fifo %p count %d buf %p, epio %p\n",
hw_ep->epnum, fifo, len, src, epio);
dump_fifo_data(src, len);
if (unlikely((unsigned long)src & 0x01))
outsw_8((unsigned long)fifo, src,
len & 0x01 ? (len >> 1) + 1 : len >> 1);
else
outsw((unsigned long)fifo, src,
len & 0x01 ? (len >> 1) + 1 : len >> 1);
}
/*
* Unload an endpoint's FIFO
*/
void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
{
void __iomem *fifo = hw_ep->fifo;
#ifdef CONFIG_BF52x
u8 epnum = hw_ep->epnum;
u16 dma_reg = 0;
invalidate_dcache_range((unsigned int)dst,
(unsigned int)(dst + len));
/* Setup DMA address register */
dma_reg = (u16) ((u32) dst & 0xFFFF);
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_LOW), dma_reg);
SSYNC();
dma_reg = (u16) (((u32) dst >> 16) & 0xFFFF);
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_ADDR_HIGH), dma_reg);
SSYNC();
/* Setup DMA count register */
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_LOW), len);
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_COUNT_HIGH), 0);
SSYNC();
/* Enable the DMA */
dma_reg = (epnum << 4) | DMA_ENA | INT_ENA;
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), dma_reg);
SSYNC();
/* Wait for compelete */
while (!(bfin_read_USB_DMA_INTERRUPT() & (1 << epnum)))
cpu_relax();
/* acknowledge dma interrupt */
bfin_write_USB_DMA_INTERRUPT(1 << epnum);
SSYNC();
/* Reset DMA */
bfin_write16(USB_DMA_REG(epnum, USB_DMAx_CTRL), 0);
SSYNC();
#else
if (unlikely((unsigned long)dst & 0x01))
insw_8((unsigned long)fifo, dst,
len & 0x01 ? (len >> 1) + 1 : len >> 1);
else
insw((unsigned long)fifo, dst,
len & 0x01 ? (len >> 1) + 1 : len >> 1);
#endif
DBG(4, "%cX ep%d fifo %p count %d buf %p\n",
'R', hw_ep->epnum, fifo, len, dst);
dump_fifo_data(dst, len);
}
static irqreturn_t blackfin_interrupt(int irq, void *__hci)
{
unsigned long flags;
irqreturn_t retval = IRQ_NONE;
struct musb *musb = __hci;
spin_lock_irqsave(&musb->lock, flags);
musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
if (musb->int_usb || musb->int_tx || musb->int_rx) {
musb_writeb(musb->mregs, MUSB_INTRUSB, musb->int_usb);
musb_writew(musb->mregs, MUSB_INTRTX, musb->int_tx);
musb_writew(musb->mregs, MUSB_INTRRX, musb->int_rx);
retval = musb_interrupt(musb);
}
spin_unlock_irqrestore(&musb->lock, flags);
/* REVISIT we sometimes get spurious IRQs on g_ep0
* not clear why... fall in BF54x too.
*/
if (retval != IRQ_HANDLED)
DBG(5, "spurious?\n");
return IRQ_HANDLED;
}
static void musb_conn_timer_handler(unsigned long _musb)
{
struct musb *musb = (void *)_musb;
unsigned long flags;
u16 val;
spin_lock_irqsave(&musb->lock, flags);
switch (musb->xceiv->state) {
case OTG_STATE_A_IDLE:
case OTG_STATE_A_WAIT_BCON:
/* Start a new session */
val = musb_readw(musb->mregs, MUSB_DEVCTL);
val |= MUSB_DEVCTL_SESSION;
musb_writew(musb->mregs, MUSB_DEVCTL, val);
val = musb_readw(musb->mregs, MUSB_DEVCTL);
if (!(val & MUSB_DEVCTL_BDEVICE)) {
gpio_set_value(musb->config->gpio_vrsel, 1);
musb->xceiv->state = OTG_STATE_A_WAIT_BCON;
} else {
gpio_set_value(musb->config->gpio_vrsel, 0);
/* Ignore VBUSERROR and SUSPEND IRQ */
val = musb_readb(musb->mregs, MUSB_INTRUSBE);
val &= ~MUSB_INTR_VBUSERROR;
musb_writeb(musb->mregs, MUSB_INTRUSBE, val);
val = MUSB_INTR_SUSPEND | MUSB_INTR_VBUSERROR;
musb_writeb(musb->mregs, MUSB_INTRUSB, val);
val = MUSB_POWER_HSENAB;
musb_writeb(musb->mregs, MUSB_POWER, val);
}
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
break;
default:
DBG(1, "%s state not handled\n", otg_state_string(musb));
break;
}
spin_unlock_irqrestore(&musb->lock, flags);
DBG(4, "state is %s\n", otg_state_string(musb));
}
void musb_platform_enable(struct musb *musb)
{
if (is_host_enabled(musb)) {
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
musb->a_wait_bcon = TIMER_DELAY;
}
}
void musb_platform_disable(struct musb *musb)
{
}
static void bfin_vbus_power(struct musb *musb, int is_on, int sleeping)
{
}
static void bfin_set_vbus(struct musb *musb, int is_on)
{
if (is_on)
gpio_set_value(musb->config->gpio_vrsel, 1);
else
gpio_set_value(musb->config->gpio_vrsel, 0);
DBG(1, "VBUS %s, devctl %02x "
/* otg %3x conf %08x prcm %08x */ "\n",
otg_state_string(musb),
musb_readb(musb->mregs, MUSB_DEVCTL));
}
static int bfin_set_power(struct otg_transceiver *x, unsigned mA)
{
return 0;
}
void musb_platform_try_idle(struct musb *musb, unsigned long timeout)
{
if (is_host_enabled(musb))
mod_timer(&musb_conn_timer, jiffies + TIMER_DELAY);
}
int musb_platform_get_vbus_status(struct musb *musb)
{
return 0;
}
int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
{
return -EIO;
}
int __init musb_platform_init(struct musb *musb)
{
/*
* Rev 1.0 BF549 EZ-KITs require PE7 to be high for both DEVICE
* and OTG HOST modes, while rev 1.1 and greater require PE7 to
* be low for DEVICE mode and high for HOST mode. We set it high
* here because we are in host mode
*/
if (gpio_request(musb->config->gpio_vrsel, "USB_VRSEL")) {
printk(KERN_ERR "Failed ro request USB_VRSEL GPIO_%d \n",
musb->config->gpio_vrsel);
return -ENODEV;
}
gpio_direction_output(musb->config->gpio_vrsel, 0);
usb_nop_xceiv_register();
musb->xceiv = otg_get_transceiver();
if (!musb->xceiv)
return -ENODEV;
if (ANOMALY_05000346) {
bfin_write_USB_APHY_CALIB(ANOMALY_05000346_value);
SSYNC();
}
if (ANOMALY_05000347) {
bfin_write_USB_APHY_CNTRL(0x0);
SSYNC();
}
/* Configure PLL oscillator register */
bfin_write_USB_PLLOSC_CTRL(0x30a8);
SSYNC();
bfin_write_USB_SRP_CLKDIV((get_sclk()/1000) / 32 - 1);
SSYNC();
bfin_write_USB_EP_NI0_RXMAXP(64);
SSYNC();
bfin_write_USB_EP_NI0_TXMAXP(64);
SSYNC();
/* Route INTRUSB/INTR_RX/INTR_TX to USB_INT0*/
bfin_write_USB_GLOBINTR(0x7);
SSYNC();
bfin_write_USB_GLOBAL_CTL(GLOBAL_ENA | EP1_TX_ENA | EP2_TX_ENA |
EP3_TX_ENA | EP4_TX_ENA | EP5_TX_ENA |
EP6_TX_ENA | EP7_TX_ENA | EP1_RX_ENA |
EP2_RX_ENA | EP3_RX_ENA | EP4_RX_ENA |
EP5_RX_ENA | EP6_RX_ENA | EP7_RX_ENA);
SSYNC();
if (is_host_enabled(musb)) {
musb->board_set_vbus = bfin_set_vbus;
setup_timer(&musb_conn_timer,
musb_conn_timer_handler, (unsigned long) musb);
}
if (is_peripheral_enabled(musb))
musb->xceiv->set_power = bfin_set_power;
musb->isr = blackfin_interrupt;
return 0;
}
int musb_platform_suspend(struct musb *musb)
{
return 0;
}
int musb_platform_resume(struct musb *musb)
{
return 0;
}
int musb_platform_exit(struct musb *musb)
{
bfin_vbus_power(musb, 0 /*off*/, 1);
gpio_free(musb->config->gpio_vrsel);
musb_platform_suspend(musb);
return 0;
}