2005-04-17 00:20:36 +02:00
|
|
|
|
Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
|
|
|
|
|
===============================================================
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
November 15, 2005
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Contents
|
|
|
|
|
========
|
|
|
|
|
|
|
|
|
|
- In This Release
|
|
|
|
|
- Identifying Your Adapter
|
|
|
|
|
- Command Line Parameters
|
|
|
|
|
- Speed and Duplex Configuration
|
|
|
|
|
- Additional Configurations
|
|
|
|
|
- Known Issues
|
|
|
|
|
- Support
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
In This Release
|
|
|
|
|
===============
|
|
|
|
|
|
|
|
|
|
This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family
|
2006-03-15 21:18:13 +01:00
|
|
|
|
of Adapters. This driver includes support for Itanium(R)2-based systems.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
For questions related to hardware requirements, refer to the documentation
|
|
|
|
|
supplied with your Intel PRO/1000 adapter. All hardware requirements listed
|
2005-04-17 00:20:36 +02:00
|
|
|
|
apply to use with Linux.
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
The following features are now available in supported kernels:
|
|
|
|
|
- Native VLANs
|
|
|
|
|
- Channel Bonding (teaming)
|
|
|
|
|
- SNMP
|
|
|
|
|
|
|
|
|
|
Channel Bonding documentation can be found in the Linux kernel source:
|
|
|
|
|
/Documentation/networking/bonding.txt
|
|
|
|
|
|
|
|
|
|
The driver information previously displayed in the /proc filesystem is not
|
|
|
|
|
supported in this release. Alternatively, you can use ethtool (version 1.6
|
|
|
|
|
or later), lspci, and ifconfig to obtain the same information.
|
|
|
|
|
|
|
|
|
|
Instructions on updating ethtool can be found in the section "Additional
|
|
|
|
|
Configurations" later in this document.
|
|
|
|
|
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
Identifying Your Adapter
|
|
|
|
|
========================
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
For more information on how to identify your adapter, go to the Adapter &
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Driver ID Guide at:
|
|
|
|
|
|
|
|
|
|
http://support.intel.com/support/network/adapter/pro100/21397.htm
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
For the latest Intel network drivers for Linux, refer to the following
|
|
|
|
|
website. In the search field, enter your adapter name or type, or use the
|
2005-04-17 00:20:36 +02:00
|
|
|
|
networking link on the left to search for your adapter:
|
|
|
|
|
|
|
|
|
|
http://downloadfinder.intel.com/scripts-df/support_intel.asp
|
|
|
|
|
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Command Line Parameters =======================
|
|
|
|
|
|
|
|
|
|
If the driver is built as a module, the following optional parameters
|
|
|
|
|
are used by entering them on the command line with the modprobe or insmod
|
|
|
|
|
command using this syntax:
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
modprobe e1000 [<option>=<VAL1>,<VAL2>,...]
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
insmod e1000 [<option>=<VAL1>,<VAL2>,...]
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
For example, with two PRO/1000 PCI adapters, entering:
|
|
|
|
|
|
|
|
|
|
insmod e1000 TxDescriptors=80,128
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
loads the e1000 driver with 80 TX descriptors for the first adapter and 128
|
|
|
|
|
TX descriptors for the second adapter.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
The default value for each parameter is generally the recommended setting,
|
2006-03-15 21:18:13 +01:00
|
|
|
|
unless otherwise noted.
|
|
|
|
|
|
|
|
|
|
NOTES: For more information about the AutoNeg, Duplex, and Speed
|
|
|
|
|
parameters, see the "Speed and Duplex Configuration" section in
|
|
|
|
|
this document.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
For more information about the InterruptThrottleRate,
|
|
|
|
|
RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
|
|
|
|
|
parameters, see the application note at:
|
|
|
|
|
http://www.intel.com/design/network/applnots/ap450.htm
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
A descriptor describes a data buffer and attributes related to
|
|
|
|
|
the data buffer. This information is accessed by the hardware.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
AutoNeg
|
|
|
|
|
-------
|
|
|
|
|
(Supported only on adapters with copper connections)
|
|
|
|
|
Valid Range: 0x01-0x0F, 0x20-0x2F
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 0x2F
|
2006-03-15 21:18:13 +01:00
|
|
|
|
|
|
|
|
|
This parameter is a bit mask that specifies which speed and duplex
|
|
|
|
|
settings the board advertises. When this parameter is used, the Speed
|
|
|
|
|
and Duplex parameters must not be specified.
|
|
|
|
|
|
|
|
|
|
NOTE: Refer to the Speed and Duplex section of this readme for more
|
|
|
|
|
information on the AutoNeg parameter.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Duplex
|
|
|
|
|
------
|
|
|
|
|
(Supported only on adapters with copper connections)
|
|
|
|
|
Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 0
|
2006-03-15 21:18:13 +01:00
|
|
|
|
|
|
|
|
|
Defines the direction in which data is allowed to flow. Can be either
|
|
|
|
|
one or two-directional. If both Duplex and the link partner are set to
|
|
|
|
|
auto-negotiate, the board auto-detects the correct duplex. If the link
|
|
|
|
|
partner is forced (either full or half), Duplex defaults to half-duplex.
|
|
|
|
|
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
FlowControl
|
2006-03-15 21:18:13 +01:00
|
|
|
|
----------
|
|
|
|
|
Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
|
|
|
|
|
Default Value: Reads flow control settings from the EEPROM
|
|
|
|
|
|
|
|
|
|
This parameter controls the automatic generation(Tx) and response(Rx)
|
|
|
|
|
to Ethernet PAUSE frames.
|
|
|
|
|
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
InterruptThrottleRate
|
2006-03-15 21:18:13 +01:00
|
|
|
|
---------------------
|
|
|
|
|
(not supported on Intel 82542, 82543 or 82544-based adapters)
|
|
|
|
|
Valid Range: 100-100000 (0=off, 1=dynamic)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 8000
|
2006-03-15 21:18:13 +01:00
|
|
|
|
|
|
|
|
|
This value represents the maximum number of interrupts per second the
|
|
|
|
|
controller generates. InterruptThrottleRate is another setting used in
|
|
|
|
|
interrupt moderation. Dynamic mode uses a heuristic algorithm to adjust
|
|
|
|
|
InterruptThrottleRate based on the current traffic load.
|
|
|
|
|
|
|
|
|
|
NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
|
|
|
|
|
RxAbsIntDelay parameters. In other words, minimizing the receive
|
|
|
|
|
and/or transmit absolute delays does not force the controller to
|
|
|
|
|
generate more interrupts than what the Interrupt Throttle Rate
|
|
|
|
|
allows.
|
|
|
|
|
|
|
|
|
|
CAUTION: If you are using the Intel PRO/1000 CT Network Connection
|
|
|
|
|
(controller 82547), setting InterruptThrottleRate to a value
|
|
|
|
|
greater than 75,000, may hang (stop transmitting) adapters
|
|
|
|
|
under certain network conditions. If this occurs a NETDEV
|
|
|
|
|
WATCHDOG message is logged in the system event log. In
|
|
|
|
|
addition, the controller is automatically reset, restoring
|
|
|
|
|
the network connection. To eliminate the potential for the
|
|
|
|
|
hang, ensure that InterruptThrottleRate is set no greater
|
|
|
|
|
than 75,000 and is not set to 0.
|
|
|
|
|
|
|
|
|
|
NOTE: When e1000 is loaded with default settings and multiple adapters
|
|
|
|
|
are in use simultaneously, the CPU utilization may increase non-
|
|
|
|
|
linearly. In order to limit the CPU utilization without impacting
|
|
|
|
|
the overall throughput, we recommend that you load the driver as
|
|
|
|
|
follows:
|
|
|
|
|
|
|
|
|
|
insmod e1000.o InterruptThrottleRate=3000,3000,3000
|
|
|
|
|
|
|
|
|
|
This sets the InterruptThrottleRate to 3000 interrupts/sec for
|
|
|
|
|
the first, second, and third instances of the driver. The range
|
|
|
|
|
of 2000 to 3000 interrupts per second works on a majority of
|
|
|
|
|
systems and is a good starting point, but the optimal value will
|
|
|
|
|
be platform-specific. If CPU utilization is not a concern, use
|
|
|
|
|
RX_POLLING (NAPI) and default driver settings.
|
|
|
|
|
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
RxDescriptors
|
2006-03-15 21:18:13 +01:00
|
|
|
|
-------------
|
|
|
|
|
Valid Range: 80-256 for 82542 and 82543-based adapters
|
|
|
|
|
80-4096 for all other supported adapters
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 256
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
This value specifies the number of receive descriptors allocated by the
|
|
|
|
|
driver. Increasing this value allows the driver to buffer more incoming
|
|
|
|
|
packets. Each descriptor is 16 bytes. A receive buffer is also
|
|
|
|
|
allocated for each descriptor and is 2048.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RxIntDelay
|
2006-03-15 21:18:13 +01:00
|
|
|
|
----------
|
|
|
|
|
Valid Range: 0-65535 (0=off)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 0
|
2006-03-15 21:18:13 +01:00
|
|
|
|
|
|
|
|
|
This value delays the generation of receive interrupts in units of 1.024
|
|
|
|
|
microseconds. Receive interrupt reduction can improve CPU efficiency if
|
|
|
|
|
properly tuned for specific network traffic. Increasing this value adds
|
|
|
|
|
extra latency to frame reception and can end up decreasing the throughput
|
|
|
|
|
of TCP traffic. If the system is reporting dropped receives, this value
|
|
|
|
|
may be set too high, causing the driver to run out of available receive
|
|
|
|
|
descriptors.
|
|
|
|
|
|
|
|
|
|
CAUTION: When setting RxIntDelay to a value other than 0, adapters may
|
|
|
|
|
hang (stop transmitting) under certain network conditions. If
|
|
|
|
|
this occurs a NETDEV WATCHDOG message is logged in the system
|
|
|
|
|
event log. In addition, the controller is automatically reset,
|
|
|
|
|
restoring the network connection. To eliminate the potential
|
|
|
|
|
for the hang ensure that RxIntDelay is set to 0.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RxAbsIntDelay
|
|
|
|
|
-------------
|
|
|
|
|
(This parameter is supported only on 82540, 82545 and later adapters.)
|
|
|
|
|
Valid Range: 0-65535 (0=off)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 128
|
2006-03-15 21:18:13 +01:00
|
|
|
|
|
|
|
|
|
This value, in units of 1.024 microseconds, limits the delay in which a
|
|
|
|
|
receive interrupt is generated. Useful only if RxIntDelay is non-zero,
|
|
|
|
|
this value ensures that an interrupt is generated after the initial
|
|
|
|
|
packet is received within the set amount of time. Proper tuning,
|
|
|
|
|
along with RxIntDelay, may improve traffic throughput in specific network
|
|
|
|
|
conditions.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Speed
|
|
|
|
|
-----
|
|
|
|
|
(This parameter is supported only on adapters with copper connections.)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Valid Settings: 0, 10, 100, 1000
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Default Value: 0 (auto-negotiate at all supported speeds)
|
|
|
|
|
|
|
|
|
|
Speed forces the line speed to the specified value in megabits per second
|
|
|
|
|
(Mbps). If this parameter is not specified or is set to 0 and the link
|
|
|
|
|
partner is set to auto-negotiate, the board will auto-detect the correct
|
|
|
|
|
speed. Duplex should also be set when Speed is set to either 10 or 100.
|
|
|
|
|
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
TxDescriptors
|
2006-03-15 21:18:13 +01:00
|
|
|
|
-------------
|
|
|
|
|
Valid Range: 80-256 for 82542 and 82543-based adapters
|
|
|
|
|
80-4096 for all other supported adapters
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 256
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
This value is the number of transmit descriptors allocated by the driver.
|
|
|
|
|
Increasing this value allows the driver to queue more transmits. Each
|
|
|
|
|
descriptor is 16 bytes.
|
|
|
|
|
|
|
|
|
|
NOTE: Depending on the available system resources, the request for a
|
|
|
|
|
higher number of transmit descriptors may be denied. In this case,
|
|
|
|
|
use a lower number.
|
|
|
|
|
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
TxIntDelay
|
2006-03-15 21:18:13 +01:00
|
|
|
|
----------
|
|
|
|
|
Valid Range: 0-65535 (0=off)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 64
|
2006-03-15 21:18:13 +01:00
|
|
|
|
|
|
|
|
|
This value delays the generation of transmit interrupts in units of
|
|
|
|
|
1.024 microseconds. Transmit interrupt reduction can improve CPU
|
|
|
|
|
efficiency if properly tuned for specific network traffic. If the
|
|
|
|
|
system is reporting dropped transmits, this value may be set too high
|
|
|
|
|
causing the driver to run out of available transmit descriptors.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TxAbsIntDelay
|
|
|
|
|
-------------
|
|
|
|
|
(This parameter is supported only on 82540, 82545 and later adapters.)
|
|
|
|
|
Valid Range: 0-65535 (0=off)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 64
|
2006-03-15 21:18:13 +01:00
|
|
|
|
|
|
|
|
|
This value, in units of 1.024 microseconds, limits the delay in which a
|
|
|
|
|
transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
|
|
|
|
|
this value ensures that an interrupt is generated after the initial
|
|
|
|
|
packet is sent on the wire within the set amount of time. Proper tuning,
|
|
|
|
|
along with TxIntDelay, may improve traffic throughput in specific
|
|
|
|
|
network conditions.
|
|
|
|
|
|
|
|
|
|
XsumRX
|
|
|
|
|
------
|
|
|
|
|
(This parameter is NOT supported on the 82542-based adapter.)
|
|
|
|
|
Valid Range: 0-1
|
2005-04-17 00:20:36 +02:00
|
|
|
|
Default Value: 1
|
2006-03-15 21:18:13 +01:00
|
|
|
|
|
|
|
|
|
A value of '1' indicates that the driver should enable IP checksum
|
|
|
|
|
offload for received packets (both UDP and TCP) to the adapter hardware.
|
|
|
|
|
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
Speed and Duplex Configuration
|
|
|
|
|
==============================
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Three keywords are used to control the speed and duplex configuration.
|
|
|
|
|
These keywords are Speed, Duplex, and AutoNeg.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
If the board uses a fiber interface, these keywords are ignored, and the
|
2005-04-17 00:20:36 +02:00
|
|
|
|
fiber interface board only links at 1000 Mbps full-duplex.
|
|
|
|
|
|
|
|
|
|
For copper-based boards, the keywords interact as follows:
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
The default operation is auto-negotiate. The board advertises all
|
|
|
|
|
supported speed and duplex combinations, and it links at the highest
|
|
|
|
|
common speed and duplex mode IF the link partner is set to auto-negotiate.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
If Speed = 1000, limited auto-negotiation is enabled and only 1000 Mbps
|
|
|
|
|
is advertised (The 1000BaseT spec requires auto-negotiation.)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
If Speed = 10 or 100, then both Speed and Duplex should be set. Auto-
|
2006-03-15 21:18:13 +01:00
|
|
|
|
negotiation is disabled, and the AutoNeg parameter is ignored. Partner
|
|
|
|
|
SHOULD also be forced.
|
|
|
|
|
|
|
|
|
|
The AutoNeg parameter is used when more control is required over the
|
|
|
|
|
auto-negotiation process. It should be used when you wish to control which
|
|
|
|
|
speed and duplex combinations are advertised during the auto-negotiation
|
|
|
|
|
process.
|
|
|
|
|
|
|
|
|
|
The parameter may be specified as either a decimal or hexidecimal value as
|
|
|
|
|
determined by the bitmap below.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Bit position 7 6 5 4 3 2 1 0
|
|
|
|
|
Decimal Value 128 64 32 16 8 4 2 1
|
|
|
|
|
Hex value 80 40 20 10 8 4 2 1
|
|
|
|
|
Speed (Mbps) N/A N/A 1000 N/A 100 100 10 10
|
|
|
|
|
Duplex Full Full Half Full Half
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Some examples of using AutoNeg:
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
modprobe e1000 AutoNeg=0x01 (Restricts autonegotiation to 10 Half)
|
|
|
|
|
modprobe e1000 AutoNeg=1 (Same as above)
|
|
|
|
|
modprobe e1000 AutoNeg=0x02 (Restricts autonegotiation to 10 Full)
|
|
|
|
|
modprobe e1000 AutoNeg=0x03 (Restricts autonegotiation to 10 Half or 10 Full)
|
|
|
|
|
modprobe e1000 AutoNeg=0x04 (Restricts autonegotiation to 100 Half)
|
|
|
|
|
modprobe e1000 AutoNeg=0x05 (Restricts autonegotiation to 10 Half or 100
|
|
|
|
|
Half)
|
|
|
|
|
modprobe e1000 AutoNeg=0x020 (Restricts autonegotiation to 1000 Full)
|
|
|
|
|
modprobe e1000 AutoNeg=32 (Same as above)
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Note that when this parameter is used, Speed and Duplex must not be specified.
|
|
|
|
|
|
|
|
|
|
If the link partner is forced to a specific speed and duplex, then this
|
|
|
|
|
parameter should not be used. Instead, use the Speed and Duplex parameters
|
|
|
|
|
previously mentioned to force the adapter to the same speed and duplex.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Additional Configurations
|
|
|
|
|
=========================
|
|
|
|
|
|
|
|
|
|
Configuring the Driver on Different Distributions
|
|
|
|
|
-------------------------------------------------
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Configuring a network driver to load properly when the system is started
|
|
|
|
|
is distribution dependent. Typically, the configuration process involves
|
|
|
|
|
adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well
|
|
|
|
|
as editing other system startup scripts and/or configuration files. Many
|
|
|
|
|
popular Linux distributions ship with tools to make these changes for you.
|
|
|
|
|
To learn the proper way to configure a network device for your system,
|
|
|
|
|
refer to your distribution documentation. If during this process you are
|
|
|
|
|
asked for the driver or module name, the name for the Linux Base Driver
|
|
|
|
|
for the Intel PRO/1000 Family of Adapters is e1000.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
As an example, if you install the e1000 driver for two PRO/1000 adapters
|
|
|
|
|
(eth0 and eth1) and set the speed and duplex to 10full and 100half, add
|
2006-10-03 22:57:56 +02:00
|
|
|
|
the following to modules.conf or modprobe.conf:
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
alias eth0 e1000
|
|
|
|
|
alias eth1 e1000
|
|
|
|
|
options e1000 Speed=10,100 Duplex=2,1
|
|
|
|
|
|
|
|
|
|
Viewing Link Messages
|
|
|
|
|
---------------------
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Link messages will not be displayed to the console if the distribution is
|
|
|
|
|
restricting system messages. In order to see network driver link messages
|
|
|
|
|
on your console, set dmesg to eight by entering the following:
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
dmesg -n 8
|
|
|
|
|
|
|
|
|
|
NOTE: This setting is not saved across reboots.
|
|
|
|
|
|
|
|
|
|
Jumbo Frames
|
|
|
|
|
------------
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
The driver supports Jumbo Frames for all adapters except 82542 and
|
|
|
|
|
82573-based adapters. Jumbo Frames support is enabled by changing the
|
|
|
|
|
MTU to a value larger than the default of 1500. Use the ifconfig command
|
|
|
|
|
to increase the MTU size. For example:
|
|
|
|
|
|
|
|
|
|
ifconfig eth<x> mtu 9000 up
|
|
|
|
|
|
|
|
|
|
This setting is not saved across reboots. It can be made permanent if
|
|
|
|
|
you add:
|
|
|
|
|
|
|
|
|
|
MTU=9000
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>. This example
|
|
|
|
|
applies to the Red Hat distributions; other distributions may store this
|
|
|
|
|
setting in a different location.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Notes:
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
- To enable Jumbo Frames, increase the MTU size on the interface beyond
|
|
|
|
|
1500.
|
|
|
|
|
- The maximum MTU setting for Jumbo Frames is 16110. This value coincides
|
|
|
|
|
with the maximum Jumbo Frames size of 16128.
|
|
|
|
|
- Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or
|
|
|
|
|
loss of link.
|
|
|
|
|
- Some Intel gigabit adapters that support Jumbo Frames have a frame size
|
|
|
|
|
limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes.
|
|
|
|
|
The adapters with this limitation are based on the Intel 82571EB and
|
|
|
|
|
82572EI controllers, which correspond to these product names:
|
|
|
|
|
Intel<65> PRO/1000 PT Dual Port Server Adapter
|
|
|
|
|
Intel<65> PRO/1000 PF Dual Port Server Adapter
|
|
|
|
|
Intel<65> PRO/1000 PT Server Adapter
|
|
|
|
|
Intel<65> PRO/1000 PT Desktop Adapter
|
|
|
|
|
Intel<65> PRO/1000 PF Server Adapter
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
- The Intel PRO/1000 PM Network Connection does not support jumbo frames.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ethtool
|
|
|
|
|
-------
|
|
|
|
|
|
|
|
|
|
The driver utilizes the ethtool interface for driver configuration and
|
|
|
|
|
diagnostics, as well as displaying statistical information. Ethtool
|
|
|
|
|
version 1.6 or later is required for this functionality.
|
|
|
|
|
|
|
|
|
|
The latest release of ethtool can be found from
|
2006-03-15 21:18:13 +01:00
|
|
|
|
http://sourceforge.net/projects/gkernel.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
|
|
|
|
|
for a more complete ethtool feature set can be enabled by upgrading
|
|
|
|
|
ethtool to ethtool-1.8.1.
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
Enabling Wake on LAN* (WoL)
|
|
|
|
|
---------------------------
|
|
|
|
|
|
|
|
|
|
WoL is configured through the Ethtool* utility. Ethtool is included with
|
2006-03-15 21:18:13 +01:00
|
|
|
|
all versions of Red Hat after Red Hat 7.2. For other Linux distributions,
|
|
|
|
|
download and install Ethtool from the following website:
|
2005-04-17 00:20:36 +02:00
|
|
|
|
http://sourceforge.net/projects/gkernel.
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
For instructions on enabling WoL with Ethtool, refer to the website listed
|
2005-04-17 00:20:36 +02:00
|
|
|
|
above.
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
WoL will be enabled on the system during the next shut down or reboot.
|
|
|
|
|
For this driver version, in order to enable WoL, the e1000 driver must be
|
2005-04-17 00:20:36 +02:00
|
|
|
|
loaded when shutting down or rebooting the system.
|
|
|
|
|
|
|
|
|
|
NAPI
|
|
|
|
|
----
|
|
|
|
|
|
|
|
|
|
NAPI (Rx polling mode) is supported in the e1000 driver. NAPI is enabled
|
2006-03-15 21:18:13 +01:00
|
|
|
|
or disabled based on the configuration of the kernel. To override
|
|
|
|
|
the default, use the following compile-time flags.
|
|
|
|
|
|
|
|
|
|
To enable NAPI, compile the driver module, passing in a configuration option:
|
|
|
|
|
|
|
|
|
|
make CFLAGS_EXTRA=-DE1000_NAPI install
|
|
|
|
|
|
|
|
|
|
To disable NAPI, compile the driver module, passing in a configuration option:
|
|
|
|
|
|
|
|
|
|
make CFLAGS_EXTRA=-DE1000_NO_NAPI install
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Known Issues
|
|
|
|
|
============
|
|
|
|
|
|
|
|
|
|
Jumbo Frames System Requirement
|
|
|
|
|
-------------------------------
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
Memory allocation failures have been observed on Linux systems with 64 MB
|
|
|
|
|
of RAM or less that are running Jumbo Frames. If you are using Jumbo
|
|
|
|
|
Frames, your system may require more than the advertised minimum
|
|
|
|
|
requirement of 64 MB of system memory.
|
|
|
|
|
|
|
|
|
|
Performance Degradation with Jumbo Frames
|
|
|
|
|
-----------------------------------------
|
|
|
|
|
|
|
|
|
|
Degradation in throughput performance may be observed in some Jumbo frames
|
|
|
|
|
environments. If this is observed, increasing the application's socket
|
|
|
|
|
buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values
|
|
|
|
|
may help. See the specific application manual and
|
|
|
|
|
/usr/src/linux*/Documentation/
|
|
|
|
|
networking/ip-sysctl.txt for more details.
|
|
|
|
|
|
|
|
|
|
Jumbo frames on Foundry BigIron 8000 switch
|
|
|
|
|
-------------------------------------------
|
|
|
|
|
There is a known issue using Jumbo frames when connected to a Foundry
|
|
|
|
|
BigIron 8000 switch. This is a 3rd party limitation. If you experience
|
|
|
|
|
loss of packets, lower the MTU size.
|
|
|
|
|
|
|
|
|
|
Multiple Interfaces on Same Ethernet Broadcast Network
|
|
|
|
|
------------------------------------------------------
|
|
|
|
|
|
|
|
|
|
Due to the default ARP behavior on Linux, it is not possible to have
|
|
|
|
|
one system on two IP networks in the same Ethernet broadcast domain
|
|
|
|
|
(non-partitioned switch) behave as expected. All Ethernet interfaces
|
|
|
|
|
will respond to IP traffic for any IP address assigned to the system.
|
|
|
|
|
This results in unbalanced receive traffic.
|
|
|
|
|
|
|
|
|
|
If you have multiple interfaces in a server, either turn on ARP
|
|
|
|
|
filtering by entering:
|
|
|
|
|
|
|
|
|
|
echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
|
|
|
|
|
(this only works if your kernel's version is higher than 2.4.5),
|
|
|
|
|
|
|
|
|
|
NOTE: This setting is not saved across reboots. The configuration
|
|
|
|
|
change can be made permanent by adding the line:
|
|
|
|
|
net.ipv4.conf.all.arp_filter = 1
|
|
|
|
|
to the file /etc/sysctl.conf
|
|
|
|
|
|
|
|
|
|
or,
|
|
|
|
|
|
|
|
|
|
install the interfaces in separate broadcast domains (either in
|
|
|
|
|
different switches or in a switch partitioned to VLANs).
|
|
|
|
|
|
|
|
|
|
82541/82547 can't link or are slow to link with some link partners
|
|
|
|
|
-----------------------------------------------------------------
|
|
|
|
|
|
|
|
|
|
There is a known compatibility issue with 82541/82547 and some
|
|
|
|
|
low-end switches where the link will not be established, or will
|
|
|
|
|
be slow to establish. In particular, these switches are known to
|
|
|
|
|
be incompatible with 82541/82547:
|
|
|
|
|
|
|
|
|
|
Planex FXG-08TE
|
|
|
|
|
I-O Data ETG-SH8
|
|
|
|
|
|
|
|
|
|
To workaround this issue, the driver can be compiled with an override
|
|
|
|
|
of the PHY's master/slave setting. Forcing master or forcing slave
|
|
|
|
|
mode will improve time-to-link.
|
|
|
|
|
|
|
|
|
|
# make EXTRA_CFLAGS=-DE1000_MASTER_SLAVE=<n>
|
|
|
|
|
|
|
|
|
|
Where <n> is:
|
|
|
|
|
|
|
|
|
|
0 = Hardware default
|
|
|
|
|
1 = Master mode
|
|
|
|
|
2 = Slave mode
|
|
|
|
|
3 = Auto master/slave
|
|
|
|
|
|
|
|
|
|
Disable rx flow control with ethtool
|
|
|
|
|
------------------------------------
|
|
|
|
|
|
|
|
|
|
In order to disable receive flow control using ethtool, you must turn
|
|
|
|
|
off auto-negotiation on the same command line.
|
|
|
|
|
|
|
|
|
|
For example:
|
|
|
|
|
|
|
|
|
|
ethtool -A eth? autoneg off rx off
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Support
|
|
|
|
|
=======
|
|
|
|
|
|
|
|
|
|
For general information, go to the Intel support website at:
|
|
|
|
|
|
|
|
|
|
http://support.intel.com
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
or the Intel Wired Networking project hosted by Sourceforge at:
|
|
|
|
|
|
|
|
|
|
http://sourceforge.net/projects/e1000
|
|
|
|
|
|
2005-04-17 00:20:36 +02:00
|
|
|
|
If an issue is identified with the released source code on the supported
|
2006-03-15 21:18:13 +01:00
|
|
|
|
kernel with a supported adapter, email the specific information related
|
|
|
|
|
to the issue to e1000-devel@lists.sourceforge.net
|
2005-04-17 00:20:36 +02:00
|
|
|
|
|
|
|
|
|
|
|
|
|
|
License
|
|
|
|
|
=======
|
|
|
|
|
|
2006-03-15 21:18:13 +01:00
|
|
|
|
This software program is released under the terms of a license agreement
|
|
|
|
|
between you ('Licensee') and Intel. Do not use or load this software or any
|
|
|
|
|
associated materials (collectively, the 'Software') until you have carefully
|
|
|
|
|
read the full terms and conditions of the file COPYING located in this software
|
|
|
|
|
package. By loading or using the Software, you agree to the terms of this
|
|
|
|
|
Agreement. If you do not agree with the terms of this Agreement, do not
|
2005-04-17 00:20:36 +02:00
|
|
|
|
install or use the Software.
|
|
|
|
|
|
|
|
|
|
* Other names and brands may be claimed as the property of others.
|