linux/include/asm-parisc/pci.h

302 lines
9.3 KiB
C
Raw Normal View History

#ifndef __ASM_PARISC_PCI_H
#define __ASM_PARISC_PCI_H
#include <asm/scatterlist.h>
/*
** HP PCI platforms generally support multiple bus adapters.
** (workstations 1-~4, servers 2-~32)
**
** Newer platforms number the busses across PCI bus adapters *sparsely*.
** E.g. 0, 8, 16, ...
**
** Under a PCI bus, most HP platforms support PPBs up to two or three
** levels deep. See "Bit3" product line.
*/
#define PCI_MAX_BUSSES 256
/* To be used as: mdelay(pci_post_reset_delay);
*
* post_reset is the time the kernel should stall to prevent anyone from
* accessing the PCI bus once #RESET is de-asserted.
* PCI spec somewhere says 1 second but with multi-PCI bus systems,
* this makes the boot time much longer than necessary.
* 20ms seems to work for all the HP PCI implementations to date.
*/
#define pci_post_reset_delay 50
/*
** pci_hba_data (aka H2P_OBJECT in HP/UX)
**
** This is the "common" or "base" data structure which HBA drivers
** (eg Dino or LBA) are required to place at the top of their own
** platform_data structure. I've heard this called "C inheritance" too.
**
** Data needed by pcibios layer belongs here.
*/
struct pci_hba_data {
void __iomem *base_addr; /* aka Host Physical Address */
const struct parisc_device *dev; /* device from PA bus walk */
struct pci_bus *hba_bus; /* primary PCI bus below HBA */
int hba_num; /* I/O port space access "key" */
struct resource bus_num; /* PCI bus numbers */
struct resource io_space; /* PIOP */
struct resource lmmio_space; /* bus addresses < 4Gb */
struct resource elmmio_space; /* additional bus addresses < 4Gb */
struct resource gmmio_space; /* bus addresses > 4Gb */
/* NOTE: Dino code assumes it can use *all* of the lmmio_space,
* elmmio_space and gmmio_space as a contiguous array of
* resources. This #define represents the array size */
#define DINO_MAX_LMMIO_RESOURCES 3
unsigned long lmmio_space_offset; /* CPU view - PCI view */
void * iommu; /* IOMMU this device is under */
/* REVISIT - spinlock to protect resources? */
#define HBA_NAME_SIZE 16
char io_name[HBA_NAME_SIZE];
char lmmio_name[HBA_NAME_SIZE];
char elmmio_name[HBA_NAME_SIZE];
char gmmio_name[HBA_NAME_SIZE];
};
#define HBA_DATA(d) ((struct pci_hba_data *) (d))
/*
** We support 2^16 I/O ports per HBA. These are set up in the form
** 0xbbxxxx, where bb is the bus number and xxxx is the I/O port
** space address.
*/
#define HBA_PORT_SPACE_BITS 16
#define HBA_PORT_BASE(h) ((h) << HBA_PORT_SPACE_BITS)
#define HBA_PORT_SPACE_SIZE (1UL << HBA_PORT_SPACE_BITS)
#define PCI_PORT_HBA(a) ((a) >> HBA_PORT_SPACE_BITS)
#define PCI_PORT_ADDR(a) ((a) & (HBA_PORT_SPACE_SIZE - 1))
#ifdef CONFIG_64BIT
#define PCI_F_EXTEND 0xffffffff00000000UL
#define PCI_IS_LMMIO(hba,a) pci_is_lmmio(hba,a)
/* We need to know if an address is LMMMIO or GMMIO.
* LMMIO requires mangling and GMMIO we must use as-is.
*/
static __inline__ int pci_is_lmmio(struct pci_hba_data *hba, unsigned long a)
{
return(((a) & PCI_F_EXTEND) == PCI_F_EXTEND);
}
/*
** Convert between PCI (IO_VIEW) addresses and processor (PA_VIEW) addresses.
** See pci.c for more conversions used by Generic PCI code.
**
** Platform characteristics/firmware guarantee that
** (1) PA_VIEW - IO_VIEW = lmmio_offset for both LMMIO and ELMMIO
** (2) PA_VIEW == IO_VIEW for GMMIO
*/
#define PCI_BUS_ADDR(hba,a) (PCI_IS_LMMIO(hba,a) \
? ((a) - hba->lmmio_space_offset) /* mangle LMMIO */ \
: (a)) /* GMMIO */
#define PCI_HOST_ADDR(hba,a) (((a) & PCI_F_EXTEND) == 0 \
? (a) + hba->lmmio_space_offset \
: (a))
#else /* !CONFIG_64BIT */
#define PCI_BUS_ADDR(hba,a) (a)
#define PCI_HOST_ADDR(hba,a) (a)
#define PCI_F_EXTEND 0UL
#define PCI_IS_LMMIO(hba,a) (1) /* 32-bit doesn't support GMMIO */
#endif /* !CONFIG_64BIT */
/*
** KLUGE: linux/pci.h include asm/pci.h BEFORE declaring struct pci_bus
** (This eliminates some of the warnings).
*/
struct pci_bus;
struct pci_dev;
/*
* If the PCI device's view of memory is the same as the CPU's view of memory,
* PCI_DMA_BUS_IS_PHYS is true. The networking and block device layers use
* this boolean for bounce buffer decisions.
*/
#ifdef CONFIG_PA20
/* All PA-2.0 machines have an IOMMU. */
#define PCI_DMA_BUS_IS_PHYS 0
#define parisc_has_iommu() do { } while (0)
#else
#if defined(CONFIG_IOMMU_CCIO) || defined(CONFIG_IOMMU_SBA)
extern int parisc_bus_is_phys; /* in arch/parisc/kernel/setup.c */
#define PCI_DMA_BUS_IS_PHYS parisc_bus_is_phys
#define parisc_has_iommu() do { parisc_bus_is_phys = 0; } while (0)
#else
#define PCI_DMA_BUS_IS_PHYS 1
#define parisc_has_iommu() do { } while (0)
#endif
#endif /* !CONFIG_PA20 */
/*
** Most PCI devices (eg Tulip, NCR720) also export the same registers
** to both MMIO and I/O port space. Due to poor performance of I/O Port
** access under HP PCI bus adapters, strongly reccomend use of MMIO
** address space.
**
** While I'm at it more PA programming notes:
**
** 1) MMIO stores (writes) are posted operations. This means the processor
** gets an "ACK" before the write actually gets to the device. A read
** to the same device (or typically the bus adapter above it) will
** force in-flight write transaction(s) out to the targeted device
** before the read can complete.
**
** 2) The Programmed I/O (PIO) data may not always be strongly ordered with
** respect to DMA on all platforms. Ie PIO data can reach the processor
** before in-flight DMA reaches memory. Since most SMP PA platforms
** are I/O coherent, it generally doesn't matter...but sometimes
** it does.
**
** I've helped device driver writers debug both types of problems.
*/
struct pci_port_ops {
u8 (*inb) (struct pci_hba_data *hba, u16 port);
u16 (*inw) (struct pci_hba_data *hba, u16 port);
u32 (*inl) (struct pci_hba_data *hba, u16 port);
void (*outb) (struct pci_hba_data *hba, u16 port, u8 data);
void (*outw) (struct pci_hba_data *hba, u16 port, u16 data);
void (*outl) (struct pci_hba_data *hba, u16 port, u32 data);
};
struct pci_bios_ops {
void (*init)(void);
void (*fixup_bus)(struct pci_bus *bus);
};
/* pci_unmap_{single,page} is not a nop, thus... */
#define DECLARE_PCI_UNMAP_ADDR(ADDR_NAME) \
dma_addr_t ADDR_NAME;
#define DECLARE_PCI_UNMAP_LEN(LEN_NAME) \
__u32 LEN_NAME;
#define pci_unmap_addr(PTR, ADDR_NAME) \
((PTR)->ADDR_NAME)
#define pci_unmap_addr_set(PTR, ADDR_NAME, VAL) \
(((PTR)->ADDR_NAME) = (VAL))
#define pci_unmap_len(PTR, LEN_NAME) \
((PTR)->LEN_NAME)
#define pci_unmap_len_set(PTR, LEN_NAME, VAL) \
(((PTR)->LEN_NAME) = (VAL))
/*
** Stuff declared in arch/parisc/kernel/pci.c
*/
extern struct pci_port_ops *pci_port;
extern struct pci_bios_ops *pci_bios;
#ifdef CONFIG_PCI
extern void pcibios_register_hba(struct pci_hba_data *);
extern void pcibios_set_master(struct pci_dev *);
#else
extern inline void pcibios_register_hba(struct pci_hba_data *x)
{
}
#endif
/*
* pcibios_assign_all_busses() is used in drivers/pci/pci.c:pci_do_scan_bus()
* 0 == check if bridge is numbered before re-numbering.
* 1 == pci_do_scan_bus() should automatically number all PCI-PCI bridges.
*
* We *should* set this to zero for "legacy" platforms and one
* for PAT platforms.
*
* But legacy platforms also need to renumber the busses below a Host
* Bus controller. Adding a 4-port Tulip card on the first PCI root
* bus of a C200 resulted in the secondary bus being numbered as 1.
* The second PCI host bus controller's root bus had already been
* assigned bus number 1 by firmware and sysfs complained.
*
* Firmware isn't doing anything wrong here since each controller
* is its own PCI domain. It's simpler and easier for us to renumber
* the busses rather than treat each Dino as a separate PCI domain.
* Eventually, we may want to introduce PCI domains for Superdome or
* rp7420/8420 boxes and then revisit this issue.
*/
#define pcibios_assign_all_busses() (1)
#define pcibios_scan_all_fns(a, b) (0)
#define PCIBIOS_MIN_IO 0x10
#define PCIBIOS_MIN_MEM 0x1000 /* NBPG - but pci/setup-res.c dies */
/* Don't support DAC yet. */
#define pci_dac_dma_supported(pci_dev, mask) (0)
/* export the pci_ DMA API in terms of the dma_ one */
#include <asm-generic/pci-dma-compat.h>
#ifdef CONFIG_PCI
static inline void pci_dma_burst_advice(struct pci_dev *pdev,
enum pci_dma_burst_strategy *strat,
unsigned long *strategy_parameter)
{
unsigned long cacheline_size;
u8 byte;
pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &byte);
if (byte == 0)
cacheline_size = 1024;
else
cacheline_size = (int) byte * 4;
*strat = PCI_DMA_BURST_MULTIPLE;
*strategy_parameter = cacheline_size;
}
#endif
extern void
pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region,
struct resource *res);
extern void
pcibios_bus_to_resource(struct pci_dev *dev, struct resource *res,
struct pci_bus_region *region);
[PATCH] Make sparc64 use setup-res.c There were three changes necessary in order to allow sparc64 to use setup-res.c: 1) Sparc64 roots the PCI I/O and MEM address space using parent resources contained in the PCI controller structure. I'm actually surprised no other platforms do this, especially ones like Alpha and PPC{,64}. These resources get linked into the iomem/ioport tree when PCI controllers are probed. So the hierarchy looks like this: iomem --| PCI controller 1 MEM space --| device 1 device 2 etc. PCI controller 2 MEM space --| ... ioport --| PCI controller 1 IO space --| ... PCI controller 2 IO space --| ... You get the idea. The drivers/pci/setup-res.c code allocates using plain iomem_space and ioport_space as the root, so that wouldn't work with the above setup. So I added a pcibios_select_root() that is used to handle this. It uses the PCI controller struct's io_space and mem_space on sparc64, and io{port,mem}_resource on every other platform to keep current behavior. 2) quirk_io_region() is buggy. It takes in raw BUS view addresses and tries to use them as a PCI resource. pci_claim_resource() expects the resource to be fully formed when it gets called. The sparc64 implementation would do the translation but that's absolutely wrong, because if the same resource gets released then re-claimed we'll adjust things twice. So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource() conversion before passing it on to pci_claim_resource(). 3) I was mistakedly __init'ing the function methods the PCI controller drivers provide on sparc64 to implement some parts of these routines. This was, of course, easy to fix. So we end up with the following, and that nasty SPARC64 makefile ifdef in drivers/pci/Makefile is finally zapped. Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-08-08 22:19:08 +02:00
static inline struct resource *
pcibios_select_root(struct pci_dev *pdev, struct resource *res)
{
struct resource *root = NULL;
if (res->flags & IORESOURCE_IO)
root = &ioport_resource;
if (res->flags & IORESOURCE_MEM)
root = &iomem_resource;
return root;
}
static inline void pcibios_add_platform_entries(struct pci_dev *dev)
{
}
static inline void pcibios_penalize_isa_irq(int irq, int active)
{
/* We don't need to penalize isa irq's */
}
static inline int pci_get_legacy_ide_irq(struct pci_dev *dev, int channel)
{
return channel ? 15 : 14;
}
#endif /* __ASM_PARISC_PCI_H */