OpenE2K
/
linux
6
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
linux/drivers/net/ibm_newemac/mal.c

810 lines
20 KiB
C
Raw Normal View History

Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
/*
* drivers/net/ibm_newemac/mal.c
*
* Memory Access Layer (MAL) support
*
ibm_newemac: Update file headers copyright notices This updates the copyright notices of the new EMAC driver to avoid confusion as who is to be blamed for new bugs. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-12-05 01:14:33 +01:00
* Copyright 2007 Benjamin Herrenschmidt, IBM Corp.
* <benh@kernel.crashing.org>
*
* Based on the arch/ppc version of the driver:
*
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
* Copyright (c) 2004, 2005 Zultys Technologies.
* Eugene Surovegin <eugene.surovegin@zultys.com> or <ebs@ebshome.net>
*
* Based on original work by
* Benjamin Herrenschmidt <benh@kernel.crashing.org>,
* David Gibson <hermes@gibson.dropbear.id.au>,
*
* Armin Kuster <akuster@mvista.com>
* Copyright 2002 MontaVista Softare Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
*/
#include <linux/delay.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 09:04:11 +01:00
#include <linux/slab.h>
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
#include "core.h"
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
#include <asm/dcr-regs.h>
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
static int mal_count;
int __devinit mal_register_commac(struct mal_instance *mal,
struct mal_commac *commac)
{
unsigned long flags;
spin_lock_irqsave(&mal->lock, flags);
MAL_DBG(mal, "reg(%08x, %08x)" NL,
commac->tx_chan_mask, commac->rx_chan_mask);
/* Don't let multiple commacs claim the same channel(s) */
if ((mal->tx_chan_mask & commac->tx_chan_mask) ||
(mal->rx_chan_mask & commac->rx_chan_mask)) {
spin_unlock_irqrestore(&mal->lock, flags);
printk(KERN_WARNING "mal%d: COMMAC channels conflict!\n",
mal->index);
return -EBUSY;
}
net: Fix new EMAC driver for NAPI changes net: Fix new EMAC driver for NAPI changes This fixes the new EMAC driver for the NAPI updates. The previous patch by Roland Dreier (already applied) to do that doesn't actually work. This applies on top of it makes it work on my test Ebony machine. This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll" posted previously. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-16 07:40:50 +02:00
if (list_empty(&mal->list))
napi_enable(&mal->napi);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
mal->tx_chan_mask |= commac->tx_chan_mask;
mal->rx_chan_mask |= commac->rx_chan_mask;
list_add(&commac->list, &mal->list);
spin_unlock_irqrestore(&mal->lock, flags);
return 0;
}
ibm_newemac: Fix section mismatch warnings This patch fixes several section mismatch warnings in the ibm_newemac driver similar to: WARNING: vmlinux.o(.devinit.text+0x3a04): Section mismatch in reference from the function emac_probe() to the function .devexit.text:tah_detach() The function __devinit emac_probe() references a function __devexit tah_detach(). Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-22 02:46:43 +02:00
void mal_unregister_commac(struct mal_instance *mal,
struct mal_commac *commac)
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
{
unsigned long flags;
spin_lock_irqsave(&mal->lock, flags);
MAL_DBG(mal, "unreg(%08x, %08x)" NL,
commac->tx_chan_mask, commac->rx_chan_mask);
mal->tx_chan_mask &= ~commac->tx_chan_mask;
mal->rx_chan_mask &= ~commac->rx_chan_mask;
list_del_init(&commac->list);
net: Fix new EMAC driver for NAPI changes net: Fix new EMAC driver for NAPI changes This fixes the new EMAC driver for the NAPI updates. The previous patch by Roland Dreier (already applied) to do that doesn't actually work. This applies on top of it makes it work on my test Ebony machine. This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll" posted previously. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-16 07:40:50 +02:00
if (list_empty(&mal->list))
napi_disable(&mal->napi);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
spin_unlock_irqrestore(&mal->lock, flags);
}
int mal_set_rcbs(struct mal_instance *mal, int channel, unsigned long size)
{
BUG_ON(channel < 0 || channel >= mal->num_rx_chans ||
size > MAL_MAX_RX_SIZE);
MAL_DBG(mal, "set_rbcs(%d, %lu)" NL, channel, size);
if (size & 0xf) {
printk(KERN_WARNING
"mal%d: incorrect RX size %lu for the channel %d\n",
mal->index, size, channel);
return -EINVAL;
}
set_mal_dcrn(mal, MAL_RCBS(channel), size >> 4);
return 0;
}
int mal_tx_bd_offset(struct mal_instance *mal, int channel)
{
BUG_ON(channel < 0 || channel >= mal->num_tx_chans);
return channel * NUM_TX_BUFF;
}
int mal_rx_bd_offset(struct mal_instance *mal, int channel)
{
BUG_ON(channel < 0 || channel >= mal->num_rx_chans);
return mal->num_tx_chans * NUM_TX_BUFF + channel * NUM_RX_BUFF;
}
void mal_enable_tx_channel(struct mal_instance *mal, int channel)
{
unsigned long flags;
spin_lock_irqsave(&mal->lock, flags);
MAL_DBG(mal, "enable_tx(%d)" NL, channel);
set_mal_dcrn(mal, MAL_TXCASR,
get_mal_dcrn(mal, MAL_TXCASR) | MAL_CHAN_MASK(channel));
spin_unlock_irqrestore(&mal->lock, flags);
}
void mal_disable_tx_channel(struct mal_instance *mal, int channel)
{
set_mal_dcrn(mal, MAL_TXCARR, MAL_CHAN_MASK(channel));
MAL_DBG(mal, "disable_tx(%d)" NL, channel);
}
void mal_enable_rx_channel(struct mal_instance *mal, int channel)
{
unsigned long flags;
ibm_newemac: Add support for 460EX/GT-type MAL rx-channel handling On some 4xx PPC's (e.g. 460EX/GT), the rx channel number is a multiple of 8 (e.g. 8 for EMAC1, 16 for EMAC2), but enabling in MAL_RXCASR needs the divided by 8 value for the bitmask. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-22 02:46:42 +02:00
/*
* On some 4xx PPC's (e.g. 460EX/GT), the rx channel is a multiple
* of 8, but enabling in MAL_RXCASR needs the divided by 8 value
* for the bitmask
*/
if (!(channel % 8))
channel >>= 3;
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
spin_lock_irqsave(&mal->lock, flags);
MAL_DBG(mal, "enable_rx(%d)" NL, channel);
set_mal_dcrn(mal, MAL_RXCASR,
get_mal_dcrn(mal, MAL_RXCASR) | MAL_CHAN_MASK(channel));
spin_unlock_irqrestore(&mal->lock, flags);
}
void mal_disable_rx_channel(struct mal_instance *mal, int channel)
{
ibm_newemac: Add support for 460EX/GT-type MAL rx-channel handling On some 4xx PPC's (e.g. 460EX/GT), the rx channel number is a multiple of 8 (e.g. 8 for EMAC1, 16 for EMAC2), but enabling in MAL_RXCASR needs the divided by 8 value for the bitmask. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-22 02:46:42 +02:00
/*
* On some 4xx PPC's (e.g. 460EX/GT), the rx channel is a multiple
* of 8, but enabling in MAL_RXCASR needs the divided by 8 value
* for the bitmask
*/
if (!(channel % 8))
channel >>= 3;
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
set_mal_dcrn(mal, MAL_RXCARR, MAL_CHAN_MASK(channel));
MAL_DBG(mal, "disable_rx(%d)" NL, channel);
}
void mal_poll_add(struct mal_instance *mal, struct mal_commac *commac)
{
unsigned long flags;
spin_lock_irqsave(&mal->lock, flags);
MAL_DBG(mal, "poll_add(%p)" NL, commac);
/* starts disabled */
set_bit(MAL_COMMAC_POLL_DISABLED, &commac->flags);
list_add_tail(&commac->poll_list, &mal->poll_list);
spin_unlock_irqrestore(&mal->lock, flags);
}
void mal_poll_del(struct mal_instance *mal, struct mal_commac *commac)
{
unsigned long flags;
spin_lock_irqsave(&mal->lock, flags);
MAL_DBG(mal, "poll_del(%p)" NL, commac);
list_del(&commac->poll_list);
spin_unlock_irqrestore(&mal->lock, flags);
}
/* synchronized by mal_poll() */
static inline void mal_enable_eob_irq(struct mal_instance *mal)
{
MAL_DBG2(mal, "enable_irq" NL);
// XXX might want to cache MAL_CFG as the DCR read can be slooooow
set_mal_dcrn(mal, MAL_CFG, get_mal_dcrn(mal, MAL_CFG) | MAL_CFG_EOPIE);
}
net: Fix new EMAC driver for NAPI changes net: Fix new EMAC driver for NAPI changes This fixes the new EMAC driver for the NAPI updates. The previous patch by Roland Dreier (already applied) to do that doesn't actually work. This applies on top of it makes it work on my test Ebony machine. This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll" posted previously. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-16 07:40:50 +02:00
/* synchronized by NAPI state */
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
static inline void mal_disable_eob_irq(struct mal_instance *mal)
{
// XXX might want to cache MAL_CFG as the DCR read can be slooooow
set_mal_dcrn(mal, MAL_CFG, get_mal_dcrn(mal, MAL_CFG) & ~MAL_CFG_EOPIE);
MAL_DBG2(mal, "disable_irq" NL);
}
static irqreturn_t mal_serr(int irq, void *dev_instance)
{
struct mal_instance *mal = dev_instance;
u32 esr = get_mal_dcrn(mal, MAL_ESR);
/* Clear the error status register */
set_mal_dcrn(mal, MAL_ESR, esr);
MAL_DBG(mal, "SERR %08x" NL, esr);
if (esr & MAL_ESR_EVB) {
if (esr & MAL_ESR_DE) {
/* We ignore Descriptor error,
* TXDE or RXDE interrupt will be generated anyway.
*/
return IRQ_HANDLED;
}
if (esr & MAL_ESR_PEIN) {
/* PLB error, it's probably buggy hardware or
* incorrect physical address in BD (i.e. bug)
*/
if (net_ratelimit())
printk(KERN_ERR
"mal%d: system error, "
"PLB (ESR = 0x%08x)\n",
mal->index, esr);
return IRQ_HANDLED;
}
/* OPB error, it's probably buggy hardware or incorrect
* EBC setup
*/
if (net_ratelimit())
printk(KERN_ERR
"mal%d: system error, OPB (ESR = 0x%08x)\n",
mal->index, esr);
}
return IRQ_HANDLED;
}
static inline void mal_schedule_poll(struct mal_instance *mal)
{
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
if (likely(napi_schedule_prep(&mal->napi))) {
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
MAL_DBG2(mal, "schedule_poll" NL);
mal_disable_eob_irq(mal);
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
__napi_schedule(&mal->napi);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
} else
MAL_DBG2(mal, "already in poll" NL);
}
static irqreturn_t mal_txeob(int irq, void *dev_instance)
{
struct mal_instance *mal = dev_instance;
u32 r = get_mal_dcrn(mal, MAL_TXEOBISR);
MAL_DBG2(mal, "txeob %08x" NL, r);
mal_schedule_poll(mal);
set_mal_dcrn(mal, MAL_TXEOBISR, r);
ibm_newemac: Fix new MAL feature handling Support for new features needed by the PPC 405EZ boards introduced some errors in the MAL and EMAC feature handling. This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is not set for those. This patch fixes these errors by wrapping the code in the appropriate #ifdefs. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-16 06:38:40 +02:00
#ifdef CONFIG_PPC_DCR_NATIVE
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
if (mal_has_feature(mal, MAL_FTR_CLEAR_ICINTSTAT))
mtdcri(SDR0, DCRN_SDR_ICINTSTAT,
(mfdcri(SDR0, DCRN_SDR_ICINTSTAT) | ICINTSTAT_ICTX));
ibm_newemac: Fix new MAL feature handling Support for new features needed by the PPC 405EZ boards introduced some errors in the MAL and EMAC feature handling. This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is not set for those. This patch fixes these errors by wrapping the code in the appropriate #ifdefs. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-16 06:38:40 +02:00
#endif
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
return IRQ_HANDLED;
}
static irqreturn_t mal_rxeob(int irq, void *dev_instance)
{
struct mal_instance *mal = dev_instance;
u32 r = get_mal_dcrn(mal, MAL_RXEOBISR);
MAL_DBG2(mal, "rxeob %08x" NL, r);
mal_schedule_poll(mal);
set_mal_dcrn(mal, MAL_RXEOBISR, r);
ibm_newemac: Fix new MAL feature handling Support for new features needed by the PPC 405EZ boards introduced some errors in the MAL and EMAC feature handling. This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is not set for those. This patch fixes these errors by wrapping the code in the appropriate #ifdefs. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-16 06:38:40 +02:00
#ifdef CONFIG_PPC_DCR_NATIVE
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
if (mal_has_feature(mal, MAL_FTR_CLEAR_ICINTSTAT))
mtdcri(SDR0, DCRN_SDR_ICINTSTAT,
(mfdcri(SDR0, DCRN_SDR_ICINTSTAT) | ICINTSTAT_ICRX));
ibm_newemac: Fix new MAL feature handling Support for new features needed by the PPC 405EZ boards introduced some errors in the MAL and EMAC feature handling. This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is not set for those. This patch fixes these errors by wrapping the code in the appropriate #ifdefs. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-16 06:38:40 +02:00
#endif
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
return IRQ_HANDLED;
}
static irqreturn_t mal_txde(int irq, void *dev_instance)
{
struct mal_instance *mal = dev_instance;
u32 deir = get_mal_dcrn(mal, MAL_TXDEIR);
set_mal_dcrn(mal, MAL_TXDEIR, deir);
MAL_DBG(mal, "txde %08x" NL, deir);
if (net_ratelimit())
printk(KERN_ERR
"mal%d: TX descriptor error (TXDEIR = 0x%08x)\n",
mal->index, deir);
return IRQ_HANDLED;
}
static irqreturn_t mal_rxde(int irq, void *dev_instance)
{
struct mal_instance *mal = dev_instance;
struct list_head *l;
u32 deir = get_mal_dcrn(mal, MAL_RXDEIR);
MAL_DBG(mal, "rxde %08x" NL, deir);
list_for_each(l, &mal->list) {
struct mal_commac *mc = list_entry(l, struct mal_commac, list);
if (deir & mc->rx_chan_mask) {
set_bit(MAL_COMMAC_RX_STOPPED, &mc->flags);
mc->ops->rxde(mc->dev);
}
}
mal_schedule_poll(mal);
set_mal_dcrn(mal, MAL_RXDEIR, deir);
return IRQ_HANDLED;
}
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
static irqreturn_t mal_int(int irq, void *dev_instance)
{
struct mal_instance *mal = dev_instance;
u32 esr = get_mal_dcrn(mal, MAL_ESR);
if (esr & MAL_ESR_EVB) {
/* descriptor error */
if (esr & MAL_ESR_DE) {
if (esr & MAL_ESR_CIDT)
return mal_rxde(irq, dev_instance);
else
return mal_txde(irq, dev_instance);
} else { /* SERR */
return mal_serr(irq, dev_instance);
}
}
return IRQ_HANDLED;
}
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
void mal_poll_disable(struct mal_instance *mal, struct mal_commac *commac)
{
/* Spinlock-type semantics: only one caller disable poll at a time */
while (test_and_set_bit(MAL_COMMAC_POLL_DISABLED, &commac->flags))
msleep(1);
net: Fix new EMAC driver for NAPI changes net: Fix new EMAC driver for NAPI changes This fixes the new EMAC driver for the NAPI updates. The previous patch by Roland Dreier (already applied) to do that doesn't actually work. This applies on top of it makes it work on my test Ebony machine. This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll" posted previously. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-16 07:40:50 +02:00
/* Synchronize with the MAL NAPI poller */
fix EMAC driver for proper napi_synchronize API The EMAC driver "fix" was merged by mistake before the dust had settled on the new napi synchronize interface (and before it got merged). The final version of that function is spelled without underscores. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-18 01:14:03 +02:00
napi_synchronize(&mal->napi);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
}
void mal_poll_enable(struct mal_instance *mal, struct mal_commac *commac)
{
smp_wmb();
clear_bit(MAL_COMMAC_POLL_DISABLED, &commac->flags);
net: Fix new EMAC driver for NAPI changes net: Fix new EMAC driver for NAPI changes This fixes the new EMAC driver for the NAPI updates. The previous patch by Roland Dreier (already applied) to do that doesn't actually work. This applies on top of it makes it work on my test Ebony machine. This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll" posted previously. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-16 07:40:50 +02:00
/* Feels better to trigger a poll here to catch up with events that
* may have happened on this channel while disabled. It will most
* probably be delayed until the next interrupt but that's mostly a
* non-issue in the context where this is called.
*/
napi_schedule(&mal->napi);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
}
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
static int mal_poll(struct napi_struct *napi, int budget)
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
{
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
struct mal_instance *mal = container_of(napi, struct mal_instance, napi);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
struct list_head *l;
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
int received = 0;
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
unsigned long flags;
net: Fix new EMAC driver for NAPI changes net: Fix new EMAC driver for NAPI changes This fixes the new EMAC driver for the NAPI updates. The previous patch by Roland Dreier (already applied) to do that doesn't actually work. This applies on top of it makes it work on my test Ebony machine. This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll" posted previously. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-16 07:40:50 +02:00
MAL_DBG2(mal, "poll(%d)" NL, budget);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
again:
/* Process TX skbs */
list_for_each(l, &mal->poll_list) {
struct mal_commac *mc =
list_entry(l, struct mal_commac, poll_list);
mc->ops->poll_tx(mc->dev);
}
/* Process RX skbs.
*
* We _might_ need something more smart here to enforce polling
* fairness.
*/
list_for_each(l, &mal->poll_list) {
struct mal_commac *mc =
list_entry(l, struct mal_commac, poll_list);
int n;
if (unlikely(test_bit(MAL_COMMAC_POLL_DISABLED, &mc->flags)))
continue;
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
n = mc->ops->poll_rx(mc->dev, budget);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (n) {
received += n;
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
budget -= n;
if (budget <= 0)
goto more_work; // XXX What if this is the last one ?
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
}
}
/* We need to disable IRQs to protect from RXDE IRQ here */
spin_lock_irqsave(&mal->lock, flags);
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
__napi_complete(napi);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
mal_enable_eob_irq(mal);
spin_unlock_irqrestore(&mal->lock, flags);
/* Check for "rotting" packet(s) */
list_for_each(l, &mal->poll_list) {
struct mal_commac *mc =
list_entry(l, struct mal_commac, poll_list);
if (unlikely(test_bit(MAL_COMMAC_POLL_DISABLED, &mc->flags)))
continue;
if (unlikely(mc->ops->peek_rx(mc->dev) ||
test_bit(MAL_COMMAC_RX_STOPPED, &mc->flags))) {
MAL_DBG2(mal, "rotting packet" NL);
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
if (napi_reschedule(napi))
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
mal_disable_eob_irq(mal);
else
MAL_DBG2(mal, "already in poll list" NL);
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
if (budget > 0)
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
goto again;
else
goto more_work;
}
mc->ops->poll_tx(mc->dev);
}
more_work:
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
MAL_DBG2(mal, "poll() %d <- %d" NL, budget, received);
return received;
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
}
static void mal_reset(struct mal_instance *mal)
{
int n = 10;
MAL_DBG(mal, "reset" NL);
set_mal_dcrn(mal, MAL_CFG, MAL_CFG_SR);
/* Wait for reset to complete (1 system clock) */
while ((get_mal_dcrn(mal, MAL_CFG) & MAL_CFG_SR) && n)
--n;
if (unlikely(!n))
printk(KERN_ERR "mal%d: reset timeout\n", mal->index);
}
int mal_get_regs_len(struct mal_instance *mal)
{
return sizeof(struct emac_ethtool_regs_subhdr) +
sizeof(struct mal_regs);
}
void *mal_dump_regs(struct mal_instance *mal, void *buf)
{
struct emac_ethtool_regs_subhdr *hdr = buf;
struct mal_regs *regs = (struct mal_regs *)(hdr + 1);
int i;
hdr->version = mal->version;
hdr->index = mal->index;
regs->tx_count = mal->num_tx_chans;
regs->rx_count = mal->num_rx_chans;
regs->cfg = get_mal_dcrn(mal, MAL_CFG);
regs->esr = get_mal_dcrn(mal, MAL_ESR);
regs->ier = get_mal_dcrn(mal, MAL_IER);
regs->tx_casr = get_mal_dcrn(mal, MAL_TXCASR);
regs->tx_carr = get_mal_dcrn(mal, MAL_TXCARR);
regs->tx_eobisr = get_mal_dcrn(mal, MAL_TXEOBISR);
regs->tx_deir = get_mal_dcrn(mal, MAL_TXDEIR);
regs->rx_casr = get_mal_dcrn(mal, MAL_RXCASR);
regs->rx_carr = get_mal_dcrn(mal, MAL_RXCARR);
regs->rx_eobisr = get_mal_dcrn(mal, MAL_RXEOBISR);
regs->rx_deir = get_mal_dcrn(mal, MAL_RXDEIR);
for (i = 0; i < regs->tx_count; ++i)
regs->tx_ctpr[i] = get_mal_dcrn(mal, MAL_TXCTPR(i));
for (i = 0; i < regs->rx_count; ++i) {
regs->rx_ctpr[i] = get_mal_dcrn(mal, MAL_RXCTPR(i));
regs->rcbs[i] = get_mal_dcrn(mal, MAL_RCBS(i));
}
return regs + 1;
}
dt/net: Eliminate users of of_platform_{,un}register_driver Get rid of users of of_platform_driver in drivers/net. The of_platform_{,un}register_driver functions are going away, so the users need to be converted to using the platform_bus_type directly. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-23 05:05:51 +01:00
static int __devinit mal_probe(struct platform_device *ofdev)
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
{
struct mal_instance *mal;
int err = 0, i, bd_size;
int index = mal_count++;
Update ibm_newemac to use dcr_host_t.base Now that dcr_host_t contains the base address, we can use that in the ibm_newemac code, rather than storing it separately. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15 11:34:34 +02:00
unsigned int dcr_base;
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
const u32 *prop;
u32 cfg;
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
unsigned long irqflags;
irq_handler_t hdlr_serr, hdlr_txde, hdlr_rxde;
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
mal = kzalloc(sizeof(struct mal_instance), GFP_KERNEL);
if (!mal) {
printk(KERN_ERR
"mal%d: out of memory allocating MAL structure!\n",
index);
return -ENOMEM;
}
mal->index = index;
mal->ofdev = ofdev;
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
mal->version = of_device_is_compatible(ofdev->dev.of_node, "ibm,mcmal2") ? 2 : 1;
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
MAL_DBG(mal, "probe" NL);
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
prop = of_get_property(ofdev->dev.of_node, "num-tx-chans", NULL);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (prop == NULL) {
printk(KERN_ERR
"mal%d: can't find MAL num-tx-chans property!\n",
index);
err = -ENODEV;
goto fail;
}
mal->num_tx_chans = prop[0];
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
prop = of_get_property(ofdev->dev.of_node, "num-rx-chans", NULL);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (prop == NULL) {
printk(KERN_ERR
"mal%d: can't find MAL num-rx-chans property!\n",
index);
err = -ENODEV;
goto fail;
}
mal->num_rx_chans = prop[0];
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
dcr_base = dcr_resource_start(ofdev->dev.of_node, 0);
Update ibm_newemac to use dcr_host_t.base Now that dcr_host_t contains the base address, we can use that in the ibm_newemac code, rather than storing it separately. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15 11:34:34 +02:00
if (dcr_base == 0) {
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
printk(KERN_ERR
"mal%d: can't find DCR resource!\n", index);
err = -ENODEV;
goto fail;
}
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
mal->dcr_host = dcr_map(ofdev->dev.of_node, dcr_base, 0x100);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (!DCR_MAP_OK(mal->dcr_host)) {
printk(KERN_ERR
"mal%d: failed to map DCRs !\n", index);
err = -ENODEV;
goto fail;
}
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
if (of_device_is_compatible(ofdev->dev.of_node, "ibm,mcmal-405ez")) {
ibm_newemac: Fix new MAL feature handling Support for new features needed by the PPC 405EZ boards introduced some errors in the MAL and EMAC feature handling. This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is not set for those. This patch fixes these errors by wrapping the code in the appropriate #ifdefs. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-16 06:38:40 +02:00
#if defined(CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT) && \
defined(CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR)
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
mal->features |= (MAL_FTR_CLEAR_ICINTSTAT |
MAL_FTR_COMMON_ERR_INT);
ibm_newemac: Fix new MAL feature handling Support for new features needed by the PPC 405EZ boards introduced some errors in the MAL and EMAC feature handling. This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is not set for those. This patch fixes these errors by wrapping the code in the appropriate #ifdefs. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-16 06:38:40 +02:00
#else
printk(KERN_ERR "%s: Support for 405EZ not enabled!\n",
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
ofdev->dev.of_node->full_name);
ibm_newemac: Fix new MAL feature handling Support for new features needed by the PPC 405EZ boards introduced some errors in the MAL and EMAC feature handling. This broke 'allmodconfig' builds as CONFIG_PPC_DCR_NATIVE is not set for those. This patch fixes these errors by wrapping the code in the appropriate #ifdefs. Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-10-16 06:38:40 +02:00
err = -ENODEV;
goto fail;
#endif
}
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
mal->txeob_irq = irq_of_parse_and_map(ofdev->dev.of_node, 0);
mal->rxeob_irq = irq_of_parse_and_map(ofdev->dev.of_node, 1);
mal->serr_irq = irq_of_parse_and_map(ofdev->dev.of_node, 2);
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
if (mal_has_feature(mal, MAL_FTR_COMMON_ERR_INT)) {
mal->txde_irq = mal->rxde_irq = mal->serr_irq;
} else {
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
mal->txde_irq = irq_of_parse_and_map(ofdev->dev.of_node, 3);
mal->rxde_irq = irq_of_parse_and_map(ofdev->dev.of_node, 4);
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
}
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (mal->txeob_irq == NO_IRQ || mal->rxeob_irq == NO_IRQ ||
mal->serr_irq == NO_IRQ || mal->txde_irq == NO_IRQ ||
mal->rxde_irq == NO_IRQ) {
printk(KERN_ERR
"mal%d: failed to map interrupts !\n", index);
err = -ENODEV;
goto fail_unmap;
}
INIT_LIST_HEAD(&mal->poll_list);
INIT_LIST_HEAD(&mal->list);
spin_lock_init(&mal->lock);
net: Add init_dummy_netdev() and fix EMAC driver using it This adds an init_dummy_netdev() function that gets a network device structure (allocation and lifetime entirely under caller's control) and initialize the minimum amount of fields so it can be used to schedule NAPI polls without registering a full blown interface. This is to be used by drivers that need to tie several hardware interfaces to a single NAPI poll scheduler due to HW limitations. It also updates the ibm_newemac driver to use that, this fixing the oops on 2.6.29 due to passing NULL as "dev" to netif_napi_add() Symbol is exported GPL only a I don't think we want binary drivers doing that sort of acrobatics (if we want them at all). Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-15 06:05:05 +01:00
init_dummy_netdev(&mal->dummy_dev);
netif_napi_add(&mal->dummy_dev, &mal->napi, mal_poll,
net: Fix new EMAC driver for NAPI changes net: Fix new EMAC driver for NAPI changes This fixes the new EMAC driver for the NAPI updates. The previous patch by Roland Dreier (already applied) to do that doesn't actually work. This applies on top of it makes it work on my test Ebony machine. This patch depends on "net: Add __napi_sycnhronize() to sync with napi poll" posted previously. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-16 07:40:50 +02:00
CONFIG_IBM_NEW_EMAC_POLL_WEIGHT);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
/* Load power-on reset defaults */
mal_reset(mal);
/* Set the MAL configuration register */
cfg = (mal->version == 2) ? MAL2_CFG_DEFAULT : MAL1_CFG_DEFAULT;
cfg |= MAL_CFG_PLBB | MAL_CFG_OPBBL | MAL_CFG_LEA;
/* Current Axon is not happy with priority being non-0, it can
* deadlock, fix it up here
*/
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
if (of_device_is_compatible(ofdev->dev.of_node, "ibm,mcmal-axon"))
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
cfg &= ~(MAL2_CFG_RPP_10 | MAL2_CFG_WPP_10);
/* Apply configuration */
set_mal_dcrn(mal, MAL_CFG, cfg);
/* Allocate space for BD rings */
BUG_ON(mal->num_tx_chans <= 0 || mal->num_tx_chans > 32);
BUG_ON(mal->num_rx_chans <= 0 || mal->num_rx_chans > 32);
bd_size = sizeof(struct mal_descriptor) *
(NUM_TX_BUFF * mal->num_tx_chans +
NUM_RX_BUFF * mal->num_rx_chans);
mal->bd_virt =
dma_alloc_coherent(&ofdev->dev, bd_size, &mal->bd_dma,
GFP_KERNEL);
if (mal->bd_virt == NULL) {
printk(KERN_ERR
"mal%d: out of memory allocating RX/TX descriptors!\n",
index);
err = -ENOMEM;
goto fail_unmap;
}
memset(mal->bd_virt, 0, bd_size);
for (i = 0; i < mal->num_tx_chans; ++i)
set_mal_dcrn(mal, MAL_TXCTPR(i), mal->bd_dma +
sizeof(struct mal_descriptor) *
mal_tx_bd_offset(mal, i));
for (i = 0; i < mal->num_rx_chans; ++i)
set_mal_dcrn(mal, MAL_RXCTPR(i), mal->bd_dma +
sizeof(struct mal_descriptor) *
mal_rx_bd_offset(mal, i));
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
if (mal_has_feature(mal, MAL_FTR_COMMON_ERR_INT)) {
irqflags = IRQF_SHARED;
hdlr_serr = hdlr_txde = hdlr_rxde = mal_int;
} else {
irqflags = 0;
hdlr_serr = mal_serr;
hdlr_txde = mal_txde;
hdlr_rxde = mal_rxde;
}
err = request_irq(mal->serr_irq, hdlr_serr, irqflags, "MAL SERR", mal);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (err)
goto fail2;
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
err = request_irq(mal->txde_irq, hdlr_txde, irqflags, "MAL TX DE", mal);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (err)
goto fail3;
err = request_irq(mal->txeob_irq, mal_txeob, 0, "MAL TX EOB", mal);
if (err)
goto fail4;
ibm_newemac: MAL support for PowerPC 405EZ The PowerPC 405EZ SoC has some differences in the interrupt layout and handling for the MAL. The SERR, TXDE, and RXDE interrupts are OR'd into a single interrupt. Also, due to the possibility for interrupt coalescing, the TXEOB and RXEOB interrupts require an interrupt bit to be cleared in the ICINTSTAT SDR. This sets the proper MAL feature bits for 405EZ boards, and adds a common shared handler for SERR, TXDE, and RXDE. The defines for the ICINTSTAT DCR are added to the proper header file as well. This has been adapted from code originally written by Stefan Roese. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-09-04 06:08:20 +02:00
err = request_irq(mal->rxde_irq, hdlr_rxde, irqflags, "MAL RX DE", mal);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (err)
goto fail5;
err = request_irq(mal->rxeob_irq, mal_rxeob, 0, "MAL RX EOB", mal);
if (err)
goto fail6;
/* Enable all MAL SERR interrupt sources */
if (mal->version == 2)
set_mal_dcrn(mal, MAL_IER, MAL2_IER_EVENTS);
else
set_mal_dcrn(mal, MAL_IER, MAL1_IER_EVENTS);
/* Enable EOB interrupt */
mal_enable_eob_irq(mal);
printk(KERN_INFO
"MAL v%d %s, %d TX channels, %d RX channels\n",
of: Always use 'struct device.of_node' to get device node pointer. The following structure elements duplicate the information in 'struct device.of_node' and so are being eliminated. This patch makes all readers of these elements use device.of_node instead. (struct of_device *)->node (struct dev_archdata *)->prom_node (sparc) (struct dev_archdata *)->of_node (powerpc & microblaze) Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-14 01:12:29 +02:00
mal->version, ofdev->dev.of_node->full_name,
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
mal->num_tx_chans, mal->num_rx_chans);
/* Advertise this instance to the rest of the world */
wmb();
dev_set_drvdata(&ofdev->dev, mal);
mal_dbg_register(mal);
return 0;
fail6:
free_irq(mal->rxde_irq, mal);
fail5:
free_irq(mal->txeob_irq, mal);
fail4:
free_irq(mal->txde_irq, mal);
fail3:
free_irq(mal->serr_irq, mal);
fail2:
dma_free_coherent(&ofdev->dev, bd_size, mal->bd_virt, mal->bd_dma);
fail_unmap:
Use dcr_host_t.base in dcr_unmap() With the base stored in dcr_host_t, there's no need for callers to pass the dcr_n into dcr_unmap(). In fact this removes the possibility of them passing the incorrect value, which would then be iounmap()'ed. Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15 11:34:37 +02:00
dcr_unmap(mal->dcr_host, 0x100);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
fail:
kfree(mal);
return err;
}
of/device: Replace struct of_device with struct platform_device of_device is just an alias for platform_device, so remove it entirely. Also replace to_of_device() with to_platform_device() and update comment blocks. This patch was initially generated from the following semantic patch, and then edited by hand to pick up the bits that coccinelle didn't catch. @@ @@ -struct of_device +struct platform_device Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: David S. Miller <davem@davemloft.net>
2010-08-06 17:25:50 +02:00
static int __devexit mal_remove(struct platform_device *ofdev)
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
{
struct mal_instance *mal = dev_get_drvdata(&ofdev->dev);
MAL_DBG(mal, "remove" NL);
ibm_emac: Convert to use napi_struct independent of struct net_device Commit da3dedd9 ("[NET]: Make NAPI polling independent of struct net_device objects.") changed the interface to NAPI polling. Fix up the ibm_newemac driver so that it works with this new interface. This is actually a nice cleanup because ibm_newemac is one of the drivers that wants to have multiple NAPI structures for a single net_device. Compile-tested only as I don't have a system that uses the ibm_newemac driver. This conversion the conversion for the ibm_emac driver that was tested on real PowerPC 440SPe hardware. Signed-off-by: Roland Dreier <rolandd@cisco.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 00:48:56 +02:00
/* Synchronize with scheduled polling */
napi_disable(&mal->napi);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
if (!list_empty(&mal->list)) {
/* This is *very* bad */
printk(KERN_EMERG
"mal%d: commac list is not empty on remove!\n",
mal->index);
WARN_ON(1);
}
dev_set_drvdata(&ofdev->dev, NULL);
free_irq(mal->serr_irq, mal);
free_irq(mal->txde_irq, mal);
free_irq(mal->txeob_irq, mal);
free_irq(mal->rxde_irq, mal);
free_irq(mal->rxeob_irq, mal);
mal_reset(mal);
mal_dbg_unregister(mal);
dma_free_coherent(&ofdev->dev,
sizeof(struct mal_descriptor) *
(NUM_TX_BUFF * mal->num_tx_chans +
NUM_RX_BUFF * mal->num_rx_chans), mal->bd_virt,
mal->bd_dma);
kfree(mal);
return 0;
}
static struct of_device_id mal_platform_match[] =
{
{
.compatible = "ibm,mcmal",
},
{
.compatible = "ibm,mcmal2",
},
/* Backward compat */
{
.type = "mcmal-dma",
.compatible = "ibm,mcmal",
},
{
.type = "mcmal-dma",
.compatible = "ibm,mcmal2",
},
{},
};
dt/net: Eliminate users of of_platform_{,un}register_driver Get rid of users of of_platform_driver in drivers/net. The of_platform_{,un}register_driver functions are going away, so the users need to be converted to using the platform_bus_type directly. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-23 05:05:51 +01:00
static struct platform_driver mal_of_driver = {
of: Remove duplicate fields from of_platform_driver .name, .match_table and .owner are duplicated in both of_platform_driver and device_driver. This patch is a removes the extra copies from struct of_platform_driver and converts all users to the device_driver members. This patch is a pretty mechanical change. The usage model doesn't change and if any drivers have been missed, or if anything has been fixed up incorrectly, then it will fail with a compile time error, and the fixup will be trivial. This patch looks big and scary because it touches so many files, but it should be pretty safe. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: Sean MacLennan <smaclennan@pikatech.com>
2010-04-14 01:13:02 +02:00
.driver = {
.name = "mcmal",
.owner = THIS_MODULE,
.of_match_table = mal_platform_match,
},
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
.probe = mal_probe,
.remove = mal_remove,
};
int __init mal_init(void)
{
dt/net: Eliminate users of of_platform_{,un}register_driver Get rid of users of of_platform_driver in drivers/net. The of_platform_{,un}register_driver functions are going away, so the users need to be converted to using the platform_bus_type directly. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-23 05:05:51 +01:00
return platform_driver_register(&mal_of_driver);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
}
void mal_exit(void)
{
dt/net: Eliminate users of of_platform_{,un}register_driver Get rid of users of of_platform_driver in drivers/net. The of_platform_{,un}register_driver functions are going away, so the users need to be converted to using the platform_bus_type directly. Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-23 05:05:51 +01:00
platform_driver_unregister(&mal_of_driver);
Device tree aware EMAC driver Based on BenH's earlier work, this is a new version of the EMAC driver for the built-in ethernet found on PowerPC 4xx embedded CPUs. The same ASIC is also found in the Axon bridge chip. This new version is designed to work in the arch/powerpc tree, using the device tree to probe the device, rather than the old and ugly arch/ppc OCP layer. This driver is designed to sit alongside the old driver (that lies in drivers/net/ibm_emac and this one in drivers/net/ibm_newemac). The old driver is left in place to support arch/ppc until arch/ppc itself reaches its final demise (not too long now, with luck). This driver still has a number of things that could do with cleaning up, but I think they can be fixed up after merging. Specifically: - Should be adjusted to properly use the dma mapping API. Axon needs this. - Probe logic needs reworking, in conjuction with the general probing code for of_platform devices. The dependencies here between EMAC, MAL, ZMII etc. make this complicated. At present, it usually works, because we initialize and register the sub-drivers before the EMAC driver itself, and (being in driver code) runs after the devices themselves have been instantiated from the device tree. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-23 05:56:01 +02:00
}