OpenE2K/linux
6
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
4d59a75125
linux/arch/arm/mach-davinci/include/mach/debug-macro.S

68 lines
1.7 KiB
ArmAsm
Raw Normal View History

[ARM] 4303/3: base kernel support for TI DaVinci Add base kernel support for the TI DaVinci platform. This patch only includes interrupts, timers, CPU identification, serial support and basic power and sleep controller init. More drivers to come. Signed-off-by: Kevin Hilman <khilman@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-04-30 20:37:19 +02:00
/*
* Debugging macro for DaVinci
*
* Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
*
* 2007 (c) MontaVista Software, Inc. This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
davinci: use 32-bit accesses for low-level debug macros This patch defines debug macros for low-level debugging for Davinci based platforms Tested on : - DM644x DaVinci EVM - DM646X DaVinciHD EVM - DM355 EVM This patch attempts to solve the low-level debug issue in DM646x. The UART on DM646x SoC allows only 32-bit access. The existing debug-macro.S uses the macros from debug-8250.S file. This led to garbage serial out in the case of DM646x. The inclusion of debug-8250.S does not allow for run time fix for this issue. There are compile time errors due to multiple definitions of the macros. Also when building a single image for multiple DaVinci Platforms, the ifdefs cannot be relied upon. The solution below does not include the debug-8250.S file and defines the necessary macros. This solution was arrived at after observing that word access does not affect the low-level debug messages on DM644x/DM355. The other approach to this issue is to use the UART module information available in the peripheral registers to decide the access mechanism. But this will have to be done for every access of UART specifically for DM646x. Also this calls for a modification of the debug-8250.S file. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-01-19 09:43:05 +01:00
/* Modifications
* Jan 2009 Chaithrika U S Added senduart, busyuart, waituart
* macros, based on debug-8250.S file
* but using 32-bit accesses required for
* some davinci devices.
*/
#include <linux/serial_reg.h>
Davinci: generalized debug macros This patch adopts a debug uart selection similar to the OMAP model. During the boot process, the uncompress code determines the physical and virtual base addresses of the board-specific debug uart. These addresses are then passed on to the in-kernel debug macros through a small chunk of memory placed just below the page tables (@0x80003ff8). Signed-off-by: Cyril Chemparathy <cyril@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-05-18 18:51:17 +02:00
#include <mach/serial.h>
davinci: use 32-bit accesses for low-level debug macros This patch defines debug macros for low-level debugging for Davinci based platforms Tested on : - DM644x DaVinci EVM - DM646X DaVinciHD EVM - DM355 EVM This patch attempts to solve the low-level debug issue in DM646x. The UART on DM646x SoC allows only 32-bit access. The existing debug-macro.S uses the macros from debug-8250.S file. This led to garbage serial out in the case of DM646x. The inclusion of debug-8250.S does not allow for run time fix for this issue. There are compile time errors due to multiple definitions of the macros. Also when building a single image for multiple DaVinci Platforms, the ifdefs cannot be relied upon. The solution below does not include the debug-8250.S file and defines the necessary macros. This solution was arrived at after observing that word access does not affect the low-level debug messages on DM644x/DM355. The other approach to this issue is to use the UART module information available in the peripheral registers to decide the access mechanism. But this will have to be done for every access of UART specifically for DM646x. Also this calls for a modification of the debug-8250.S file. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-01-19 09:43:05 +01:00
#define UART_SHIFT 2
ARM: davinci: implement DEBUG_LL port choice Apart from the necessity to do this change for multi-platform kernels the previous logic depended on the zImage decompressor to write the physical and virtual address to a magic memory location. If the decompressor is unused or not correctly configured for the current machid, the addruart macro was an infinite loop. Moreover debugging the early zImage code was not possible either. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [nsekhar@ti.com: add braces in _DEBUG_LL_ENTRY() macro to fix checkpatch error. Fix debug port choice config dependency for traditional DaVincis. Modify debug port config names and add help text.] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2012-03-22 10:29:23 +01:00
#if defined(CONFIG_DEBUG_DAVINCI_DMx_UART0)
#define UART_BASE DAVINCI_UART0_BASE
#elif defined(CONFIG_DEBUG_DAVINCI_DA8XX_UART0)
#define UART_BASE DA8XX_UART0_BASE
#elif defined(CONFIG_DEBUG_DAVINCI_DA8XX_UART1)
#define UART_BASE DA8XX_UART1_BASE
#elif defined(CONFIG_DEBUG_DAVINCI_DA8XX_UART2)
#define UART_BASE DA8XX_UART2_BASE
#elif defined(CONFIG_DEBUG_DAVINCI_TNETV107X_UART1)
#define UART_BASE TNETV107X_UART2_BASE
#define UART_VIRTBASE TNETV107X_UART2_VIRT
#else
#error "Select a specifc port for DEBUG_LL"
#endif
ARM: mach-davinci: clean up debug-macro.S This achieves two goals: 1) Get rid of davinci_uart_v2p() and davinci_uart_p2v() which were the last users of PLAT_PHYS_OFFSET. 2) Remove the probing of the M bit in the CP15 control reg and make the access to the .data variables completely position independent. Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org> Reviewed-by: Kevin Hilman <khilman@ti.com> Tested-by: Kevin Hilman <khilman@ti.com>
2011-09-02 02:50:14 +02:00
ARM: davinci: implement DEBUG_LL port choice Apart from the necessity to do this change for multi-platform kernels the previous logic depended on the zImage decompressor to write the physical and virtual address to a magic memory location. If the decompressor is unused or not correctly configured for the current machid, the addruart macro was an infinite loop. Moreover debugging the early zImage code was not possible either. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [nsekhar@ti.com: add braces in _DEBUG_LL_ENTRY() macro to fix checkpatch error. Fix debug port choice config dependency for traditional DaVincis. Modify debug port config names and add help text.] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2012-03-22 10:29:23 +01:00
#ifndef UART_VIRTBASE
#define UART_VIRTBASE IO_ADDRESS(UART_BASE)
#endif
ARM: mach-davinci: clean up debug-macro.S This achieves two goals: 1) Get rid of davinci_uart_v2p() and davinci_uart_p2v() which were the last users of PLAT_PHYS_OFFSET. 2) Remove the probing of the M bit in the CP15 control reg and make the access to the .data variables completely position independent. Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org> Reviewed-by: Kevin Hilman <khilman@ti.com> Tested-by: Kevin Hilman <khilman@ti.com>
2011-09-02 02:50:14 +02:00
ARM: davinci: implement DEBUG_LL port choice Apart from the necessity to do this change for multi-platform kernels the previous logic depended on the zImage decompressor to write the physical and virtual address to a magic memory location. If the decompressor is unused or not correctly configured for the current machid, the addruart macro was an infinite loop. Moreover debugging the early zImage code was not possible either. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> [nsekhar@ti.com: add braces in _DEBUG_LL_ENTRY() macro to fix checkpatch error. Fix debug port choice config dependency for traditional DaVincis. Modify debug port config names and add help text.] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2012-03-22 10:29:23 +01:00
.macro addruart, rp, rv, tmp
ldr \rp, =UART_BASE
ldr \rv, =UART_VIRTBASE
[ARM] 4303/3: base kernel support for TI DaVinci Add base kernel support for the TI DaVinci platform. This patch only includes interrupts, timers, CPU identification, serial support and basic power and sleep controller init. More drivers to come. Signed-off-by: Kevin Hilman <khilman@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-04-30 20:37:19 +02:00
.endm
davinci: use 32-bit accesses for low-level debug macros This patch defines debug macros for low-level debugging for Davinci based platforms Tested on : - DM644x DaVinci EVM - DM646X DaVinciHD EVM - DM355 EVM This patch attempts to solve the low-level debug issue in DM646x. The UART on DM646x SoC allows only 32-bit access. The existing debug-macro.S uses the macros from debug-8250.S file. This led to garbage serial out in the case of DM646x. The inclusion of debug-8250.S does not allow for run time fix for this issue. There are compile time errors due to multiple definitions of the macros. Also when building a single image for multiple DaVinci Platforms, the ifdefs cannot be relied upon. The solution below does not include the debug-8250.S file and defines the necessary macros. This solution was arrived at after observing that word access does not affect the low-level debug messages on DM644x/DM355. The other approach to this issue is to use the UART module information available in the peripheral registers to decide the access mechanism. But this will have to be done for every access of UART specifically for DM646x. Also this calls for a modification of the debug-8250.S file. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2009-01-19 09:43:05 +01:00
.macro senduart,rd,rx
str \rd, [\rx, #UART_TX << UART_SHIFT]
.endm
.macro busyuart,rd,rx
1002: ldr \rd, [\rx, #UART_LSR << UART_SHIFT]
and \rd, \rd, #UART_LSR_TEMT | UART_LSR_THRE
teq \rd, #UART_LSR_TEMT | UART_LSR_THRE
bne 1002b
.endm
.macro waituart,rd,rx
#ifdef FLOW_CONTROL
1001: ldr \rd, [\rx, #UART_MSR << UART_SHIFT]
tst \rd, #UART_MSR_CTS
beq 1001b
#endif
.endm
Reference in New Issue Copy Permalink