linux/Documentation/networking/batman-adv.rst

223 lines
7.5 KiB
ReStructuredText
Raw Normal View History

.. SPDX-License-Identifier: GPL-2.0
==========
batman-adv
==========
Batman advanced is a new approach to wireless networking which does no longer
operate on the IP basis. Unlike the batman daemon, which exchanges information
using UDP packets and sets routing tables, batman-advanced operates on ISO/OSI
Layer 2 only and uses and routes (or better: bridges) Ethernet Frames. It
emulates a virtual network switch of all nodes participating. Therefore all
nodes appear to be link local, thus all higher operating protocols won't be
affected by any changes within the network. You can run almost any protocol
above batman advanced, prominent examples are: IPv4, IPv6, DHCP, IPX.
Batman advanced was implemented as a Linux kernel driver to reduce the overhead
to a minimum. It does not depend on any (other) network driver, and can be used
on wifi as well as ethernet lan, vpn, etc ... (anything with ethernet-style
layer 2).
Configuration
=============
Load the batman-adv module into your kernel::
$ insmod batman-adv.ko
The module is now waiting for activation. You must add some interfaces on which
batman can operate. After loading the module batman advanced will scan your
systems interfaces to search for compatible interfaces. Once found, it will
create subfolders in the ``/sys`` directories of each supported interface,
e.g.::
$ ls /sys/class/net/eth0/batman_adv/
elp_interval iface_status mesh_iface throughput_override
If an interface does not have the ``batman_adv`` subfolder, it probably is not
supported. Not supported interfaces are: loopback, non-ethernet and batman's
own interfaces.
Note: After the module was loaded it will continuously watch for new
interfaces to verify the compatibility. There is no need to reload the module
if you plug your USB wifi adapter into your machine after batman advanced was
initially loaded.
The batman-adv soft-interface can be created using the iproute2 tool ``ip``::
$ ip link add name bat0 type batadv
To activate a given interface simply attach it to the ``bat0`` interface::
$ ip link set dev eth0 master bat0
Repeat this step for all interfaces you wish to add. Now batman starts
using/broadcasting on this/these interface(s).
By reading the "iface_status" file you can check its status::
$ cat /sys/class/net/eth0/batman_adv/iface_status
active
To deactivate an interface you have to detach it from the "bat0" interface::
$ ip link set dev eth0 nomaster
All mesh wide settings can be found in batman's own interface folder::
$ ls /sys/class/net/bat0/mesh/
aggregated_ogms fragmentation isolation_mark routing_algo
ap_isolation gw_bandwidth log_level vlan0
bonding gw_mode multicast_mode
bridge_loop_avoidance gw_sel_class network_coding
distributed_arp_table hop_penalty orig_interval
There is a special folder for debugging information::
$ ls /sys/kernel/debug/batman_adv/bat0/
bla_backbone_table log neighbors transtable_local
bla_claim_table mcast_flags originators
dat_cache nc socket
gateways nc_nodes transtable_global
Some of the files contain all sort of status information regarding the mesh
network. For example, you can view the table of originators (mesh
participants) with::
$ cat /sys/kernel/debug/batman_adv/bat0/originators
Other files allow to change batman's behaviour to better fit your requirements.
For instance, you can check the current originator interval (value in
milliseconds which determines how often batman sends its broadcast packets)::
$ cat /sys/class/net/bat0/mesh/orig_interval
1000
and also change its value::
$ echo 3000 > /sys/class/net/bat0/mesh/orig_interval
In very mobile scenarios, you might want to adjust the originator interval to a
lower value. This will make the mesh more responsive to topology changes, but
will also increase the overhead.
Usage
=====
To make use of your newly created mesh, batman advanced provides a new
interface "bat0" which you should use from this point on. All interfaces added
to batman advanced are not relevant any longer because batman handles them for
you. Basically, one "hands over" the data by using the batman interface and
batman will make sure it reaches its destination.
The "bat0" interface can be used like any other regular interface. It needs an
IP address which can be either statically configured or dynamically (by using
DHCP or similar services)::
NodeA: ip link set up dev bat0
NodeA: ip addr add 192.168.0.1/24 dev bat0
NodeB: ip link set up dev bat0
NodeB: ip addr add 192.168.0.2/24 dev bat0
NodeB: ping 192.168.0.1
Note: In order to avoid problems remove all IP addresses previously assigned to
interfaces now used by batman advanced, e.g.::
$ ip addr flush dev eth0
Logging/Debugging
=================
All error messages, warnings and information messages are sent to the kernel
log. Depending on your operating system distribution this can be read in one of
a number of ways. Try using the commands: ``dmesg``, ``logread``, or looking in
the files ``/var/log/kern.log`` or ``/var/log/syslog``. All batman-adv messages
are prefixed with "batman-adv:" So to see just these messages try::
$ dmesg | grep batman-adv
When investigating problems with your mesh network, it is sometimes necessary to
see more detail debug messages. This must be enabled when compiling the
batman-adv module. When building batman-adv as part of kernel, use "make
menuconfig" and enable the option ``B.A.T.M.A.N. debugging``
(``CONFIG_BATMAN_ADV_DEBUG=y``).
Those additional debug messages can be accessed using a special file in
debugfs::
$ cat /sys/kernel/debug/batman_adv/bat0/log
The additional debug output is by default disabled. It can be enabled during
run time. Following log_levels are defined:
.. flat-table::
* - 0
- All debug output disabled
* - 1
- Enable messages related to routing / flooding / broadcasting
* - 2
- Enable messages related to route added / changed / deleted
* - 4
- Enable messages related to translation table operations
* - 8
- Enable messages related to bridge loop avoidance
* - 16
- Enable messages related to DAT, ARP snooping and parsing
* - 32
- Enable messages related to network coding
* - 64
- Enable messages related to multicast
* - 128
- Enable messages related to throughput meter
* - 255
- Enable all messages
The debug output can be changed at runtime using the file
``/sys/class/net/bat0/mesh/log_level``. e.g.::
$ echo 6 > /sys/class/net/bat0/mesh/log_level
will enable debug messages for when routes change.
Counters for different types of packets entering and leaving the batman-adv
module are available through ethtool::
$ ethtool --statistics bat0
batctl
======
As batman advanced operates on layer 2, all hosts participating in the virtual
switch are completely transparent for all protocols above layer 2. Therefore
the common diagnosis tools do not work as expected. To overcome these problems,
batctl was created. At the moment the batctl contains ping, traceroute, tcpdump
and interfaces to the kernel module settings.
For more information, please see the manpage (``man batctl``).
batctl is available on https://www.open-mesh.org/
Contact
=======
Please send us comments, experiences, questions, anything :)
IRC:
#batman on irc.freenode.org
Mailing-list:
b.a.t.m.a.n@open-mesh.org (optional subscription at
https://lists.open-mesh.org/mm/listinfo/b.a.t.m.a.n)
You can also contact the Authors:
* Marek Lindner <mareklindner@neomailbox.ch>
* Simon Wunderlich <sw@simonwunderlich.de>