linux/drivers/net/cxgb3/version.h

45 lines
1.8 KiB
C
Raw Normal View History

/*
* Copyright (c) 2003-2007 Chelsio, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* licenses. You may choose to be licensed under the terms of the GNU
* General Public License (GPL) Version 2, available from the file
* COPYING in the main directory of this source tree, or the
* OpenIB.org BSD license below:
*
* Redistribution and use in source and binary forms, with or
* without modification, are permitted provided that the following
* conditions are met:
*
* - Redistributions of source code must retain the above
* copyright notice, this list of conditions and the following
* disclaimer.
*
* - Redistributions in binary form must reproduce the above
* copyright notice, this list of conditions and the following
* disclaimer in the documentation and/or other materials
* provided with the distribution.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
* BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
* ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
* CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
* SOFTWARE.
*/
/* $Date: 2006/10/31 18:57:51 $ $RCSfile: version.h,v $ $Revision: 1.3 $ */
#ifndef __CHELSIO_VERSION_H
#define __CHELSIO_VERSION_H
#define DRV_DESC "Chelsio T3 Network Driver"
#define DRV_NAME "cxgb3"
/* Driver version */
#define DRV_VERSION "1.0-ko"
/* Firmware version */
RDMA/cxgb3: Support peer-2-peer connection setup Open MPI, Intel MPI and other applications don't respect the iWARP requirement that the client (active) side of the connection send the first RDMA message. This class of application connection setup is called peer-to-peer. Typically once the connection is setup, _both_ sides want to send data. This patch enables supporting peer-to-peer over the chelsio RNIC by enforcing this iWARP requirement in the driver itself as part of RDMA connection setup. Connection setup is extended, when the peer2peer module option is 1, such that the MPA initiator will send a 0B Read (the RTR) just after connection setup. The MPA responder will suspend SQ processing until the RTR message is received and reply-to. In the longer term, this will be handled in a standardized way by enhancing the MPA negotiation so peers can indicate whether they want/need the RTR and what type of RTR (0B read, 0B write, or 0B send) should be sent. This will be done by standardizing a few bits of the private data in order to negotiate all this. However this patch enables peer-to-peer applications now and allows most of the required firmware and driver changes to be done and tested now. Design: - Add a module option, peer2peer, to enable this mode. - New firmware support for peer-to-peer mode: - a new bit in the rdma_init WR to tell it to do peer-2-peer and what form of RTR message to send or expect. - process _all_ preposted recvs before moving the connection into rdma mode. - passive side: defer completing the rdma_init WR until all pre-posted recvs are processed. Suspend SQ processing until the RTR is received. - active side: expect and process the 0B read WR on offload TX queue. Defer completing the rdma_init WR until all pre-posted recvs are processed. Suspend SQ processing until the 0B read WR is processed from the offload TX queue. - If peer2peer is set, driver posts 0B read request on offload TX queue just after posting the rdma_init WR to the offload TX queue. - Add CQ poll logic to ignore unsolicitied read responses. Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-29 22:46:52 +02:00
#define FW_VERSION_MAJOR 6
#define FW_VERSION_MINOR 0
#define FW_VERSION_MICRO 0
#endif /* __CHELSIO_VERSION_H */