linux/drivers/ata/pata_hpt3x2n.c

589 lines
15 KiB
C
Raw Normal View History

/*
* Libata driver for the highpoint 372N and 302N UDMA66 ATA controllers.
*
* This driver is heavily based upon:
*
* linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
*
* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
* Portions Copyright (C) 2005-2009 MontaVista Software, Inc.
*
*
* TODO
* Work out best PLL policy
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_hpt3x2n"
#define DRV_VERSION "0.3.10"
enum {
HPT_PCI_FAST = (1 << 31),
PCI66 = (1 << 1),
USE_DPLL = (1 << 0)
};
struct hpt_clock {
u8 xfer_speed;
u32 timing;
};
struct hpt_chip {
const char *name;
struct hpt_clock *clocks[3];
};
/* key for bus clock timings
* bit
* 0:3 data_high_time. Inactive time of DIOW_/DIOR_ for PIO and MW DMA.
* cycles = value + 1
* 4:8 data_low_time. Active time of DIOW_/DIOR_ for PIO and MW DMA.
* cycles = value + 1
* 9:12 cmd_high_time. Inactive time of DIOW_/DIOR_ during task file
* register access.
* 13:17 cmd_low_time. Active time of DIOW_/DIOR_ during task file
* register access.
* 18:20 udma_cycle_time. Clock cycles for UDMA xfer.
* 21 CLK frequency for UDMA: 0=ATA clock, 1=dual ATA clock.
* 22:24 pre_high_time. Time to initialize 1st cycle for PIO and MW DMA xfer.
* 25:27 cmd_pre_high_time. Time to initialize 1st PIO cycle for task file
* register access.
* 28 UDMA enable.
* 29 DMA enable.
* 30 PIO_MST enable. If set, the chip is in bus master mode during
* PIO xfer.
* 31 FIFO enable. Only for PIO.
*/
/* 66MHz DPLL clocks */
static struct hpt_clock hpt3x2n_clocks[] = {
{ XFER_UDMA_7, 0x1c869c62 },
{ XFER_UDMA_6, 0x1c869c62 },
{ XFER_UDMA_5, 0x1c8a9c62 },
{ XFER_UDMA_4, 0x1c8a9c62 },
{ XFER_UDMA_3, 0x1c8e9c62 },
{ XFER_UDMA_2, 0x1c929c62 },
{ XFER_UDMA_1, 0x1c9a9c62 },
{ XFER_UDMA_0, 0x1c829c62 },
{ XFER_MW_DMA_2, 0x2c829c62 },
{ XFER_MW_DMA_1, 0x2c829c66 },
{ XFER_MW_DMA_0, 0x2c829d2e },
{ XFER_PIO_4, 0x0c829c62 },
{ XFER_PIO_3, 0x0c829c84 },
{ XFER_PIO_2, 0x0c829ca6 },
{ XFER_PIO_1, 0x0d029d26 },
{ XFER_PIO_0, 0x0d029d5e },
};
/**
* hpt3x2n_find_mode - reset the hpt3x2n bus
* @ap: ATA port
* @speed: transfer mode
*
* Return the 32bit register programming information for this channel
* that matches the speed provided. For the moment the clocks table
* is hard coded but easy to change. This will be needed if we use
* different DPLLs
*/
static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed)
{
struct hpt_clock *clocks = hpt3x2n_clocks;
while(clocks->xfer_speed) {
if (clocks->xfer_speed == speed)
return clocks->timing;
clocks++;
}
BUG();
return 0xffffffffU; /* silence compiler warning */
}
/**
* hpt3x2n_cable_detect - Detect the cable type
* @ap: ATA port to detect on
*
* Return the cable type attached to this port
*/
static int hpt3x2n_cable_detect(struct ata_port *ap)
{
u8 scr2, ata66;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
pci_read_config_byte(pdev, 0x5B, &scr2);
pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
udelay(10); /* debounce */
/* Cable register now active */
pci_read_config_byte(pdev, 0x5A, &ata66);
/* Restore state */
pci_write_config_byte(pdev, 0x5B, scr2);
if (ata66 & (2 >> ap->port_no))
return ATA_CBL_PATA40;
else
return ATA_CBL_PATA80;
}
/**
* hpt3x2n_pre_reset - reset the hpt3x2n bus
* @link: ATA link to reset
* @deadline: deadline jiffies for the operation
*
* Perform the initial reset handling for the 3x2n series controllers.
* Reset the hardware and state machine,
*/
libata: make reset related methods proper port operations Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 04:22:50 +01:00
static int hpt3x2n_pre_reset(struct ata_link *link, unsigned long deadline)
{
struct ata_port *ap = link->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
/* Reset the state machine */
pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(100);
libata: add deadline support to prereset and reset methods Add @deadline to prereset and reset methods and make them honor it. ata_wait_ready() which directly takes @deadline is implemented to be used as the wait function. This patch is in preparation for EH timing improvements. * ata_wait_ready() never does busy sleep. It's only used from EH and no wait in EH is that urgent. This function also prints 'be patient' message automatically after 5 secs of waiting if more than 3 secs is remaining till deadline. * ata_bus_post_reset() now fails with error code if any of its wait fails. This is important because earlier reset tries will have shorter timeout than the spec requires. If a device fails to respond before the short timeout, reset should be retried with longer timeout rather than silently ignoring the device. There are three behavior differences. 1. Timeout is applied to both devices at once, not separately. This is more consistent with what the spec says. 2. When a device passes devchk but fails to become ready before deadline. Previouly, post_reset would just succeed and let device classification remove the device. New code fails the reset thus causing reset retry. After a few times, EH will give up disabling the port. 3. When slave device passes devchk but fails to become accessible (TF-wise) after reset. Original code disables dev1 after 30s timeout and continues as if the device doesn't exist, while the patched code fails reset. When this happens, new code fails reset on whole port rather than proceeding with only the primary device. If the failing device is suffering transient problems, new code retries reset which is a better behavior. If the failing device is actually broken, the net effect is identical to it, but not to the other device sharing the channel. In the previous code, reset would have succeeded after 30s thus detecting the working one. In the new code, reset fails and whole port gets disabled. IMO, it's a pathological case anyway (broken device sharing bus with working one) and doesn't really matter. * ata_bus_softreset() is changed to return error code from ata_bus_post_reset(). It used to return 0 unconditionally. * Spin up waiting is to be removed and not converted to honor deadline. * To be on the safe side, deadline is set to 40s for the time being. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-02 08:50:52 +01:00
return ata_sff_prereset(link, deadline);
}
static void hpt3x2n_set_mode(struct ata_port *ap, struct ata_device *adev,
u8 mode)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
u32 addr1, addr2;
u32 reg, timing, mask;
u8 fast;
addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
addr2 = 0x51 + 4 * ap->port_no;
/* Fast interrupt prediction disable, hold off interrupt disable */
pci_read_config_byte(pdev, addr2, &fast);
fast &= ~0x07;
pci_write_config_byte(pdev, addr2, fast);
/* Determine timing mask and find matching mode entry */
if (mode < XFER_MW_DMA_0)
mask = 0xcfc3ffff;
else if (mode < XFER_UDMA_0)
mask = 0x31c001ff;
else
mask = 0x303c0000;
timing = hpt3x2n_find_mode(ap, mode);
pci_read_config_dword(pdev, addr1, &reg);
reg = (reg & ~mask) | (timing & mask);
pci_write_config_dword(pdev, addr1, reg);
}
/**
* hpt3x2n_set_piomode - PIO setup
* @ap: ATA interface
* @adev: device on the interface
*
* Perform PIO mode setup.
*/
static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
hpt3x2n_set_mode(ap, adev, adev->pio_mode);
}
/**
* hpt3x2n_set_dmamode - DMA timing setup
* @ap: ATA interface
* @adev: Device being configured
*
* Set up the channel for MWDMA or UDMA modes.
*/
static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
hpt3x2n_set_mode(ap, adev, adev->dma_mode);
}
/**
* hpt3x2n_bmdma_end - DMA engine stop
* @qc: ATA command
*
* Clean up after the HPT3x2n and later DMA engine
*/
static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int mscreg = 0x50 + 2 * ap->port_no;
u8 bwsr_stat, msc_stat;
pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
pci_read_config_byte(pdev, mscreg, &msc_stat);
if (bwsr_stat & (1 << ap->port_no))
pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
ata_bmdma_stop(qc);
}
/**
* hpt3x2n_set_clock - clock control
* @ap: ATA port
* @source: 0x21 or 0x23 for PLL or PCI sourced clock
*
* Switch the ATA bus clock between the PLL and PCI clock sources
* while correctly isolating the bus and resetting internal logic
*
* We must use the DPLL for
* - writing
* - second channel UDMA7 (SATA ports) or higher
* - 66MHz PCI
*
* or we will underclock the device and get reduced performance.
*/
static void hpt3x2n_set_clock(struct ata_port *ap, int source)
{
void __iomem *bmdma = ap->ioaddr.bmdma_addr - ap->port_no * 8;
/* Tristate the bus */
iowrite8(0x80, bmdma+0x73);
iowrite8(0x80, bmdma+0x77);
/* Switch clock and reset channels */
iowrite8(source, bmdma+0x7B);
iowrite8(0xC0, bmdma+0x79);
/* Reset state machines, avoid enabling the disabled channels */
iowrite8(ioread8(bmdma+0x70) | 0x32, bmdma+0x70);
iowrite8(ioread8(bmdma+0x74) | 0x32, bmdma+0x74);
/* Complete reset */
iowrite8(0x00, bmdma+0x79);
/* Reconnect channels to bus */
iowrite8(0x00, bmdma+0x73);
iowrite8(0x00, bmdma+0x77);
}
static int hpt3x2n_use_dpll(struct ata_port *ap, int writing)
{
long flags = (long)ap->host->private_data;
/* See if we should use the DPLL */
if (writing)
return USE_DPLL; /* Needed for write */
if (flags & PCI66)
return USE_DPLL; /* Needed at 66Mhz */
return 0;
}
static int hpt3x2n_qc_defer(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct ata_port *alt = ap->host->ports[ap->port_no ^ 1];
int rc, flags = (long)ap->host->private_data;
int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
/* First apply the usual rules */
rc = ata_std_qc_defer(qc);
if (rc != 0)
return rc;
if ((flags & USE_DPLL) != dpll && alt->qc_active)
return ATA_DEFER_PORT;
return 0;
}
static unsigned int hpt3x2n_qc_issue(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
int flags = (long)ap->host->private_data;
int dpll = hpt3x2n_use_dpll(ap, qc->tf.flags & ATA_TFLAG_WRITE);
if ((flags & USE_DPLL) != dpll) {
flags &= ~USE_DPLL;
flags |= dpll;
ap->host->private_data = (void *)(long)flags;
hpt3x2n_set_clock(ap, dpll ? 0x21 : 0x23);
}
return ata_bmdma_qc_issue(qc);
}
static struct scsi_host_template hpt3x2n_sht = {
ATA_BMDMA_SHT(DRV_NAME),
};
/*
* Configuration for HPT3x2n.
*/
static struct ata_port_operations hpt3x2n_port_ops = {
libata: implement and use ops inheritance libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 04:22:49 +01:00
.inherits = &ata_bmdma_port_ops,
.bmdma_stop = hpt3x2n_bmdma_stop,
.qc_defer = hpt3x2n_qc_defer,
.qc_issue = hpt3x2n_qc_issue,
libata: implement and use ops inheritance libata lets low level drivers build ata_port_operations table and register it with libata core layer. This allows low level drivers high level of flexibility but also burdens them with lots of boilerplate entries. This becomes worse for drivers which support related similar controllers which differ slightly. They share most of the operations except for a few. However, the driver still needs to list all operations for each variant. This results in large number of duplicate entries, which is not only inefficient but also error-prone as it becomes very difficult to tell what the actual differences are. This duplicate boilerplates all over the low level drivers also make updating the core layer exteremely difficult and error-prone. When compounded with multi-branched development model, it ends up accumulating inconsistencies over time. Some of those inconsistencies cause immediate problems and fixed. Others just remain there dormant making maintenance increasingly difficult. To rectify the problem, this patch implements ata_port_operations inheritance. To allow LLDs to easily re-use their own ops tables overriding only specific methods, this patch implements poor man's class inheritance. An ops table has ->inherits field which can be set to any ops table as long as it doesn't create a loop. When the host is started, the inheritance chain is followed and any operation which isn't specified is taken from the nearest ancestor which has it specified. This operation is called finalization and done only once per an ops table and the LLD doesn't have to do anything special about it other than making the ops table non-const such that libata can update it. libata provides four base ops tables lower drivers can inherit from - base, sata, pmp, sff and bmdma. To avoid overriding these ops accidentaly, these ops are declared const and LLDs should always inherit these instead of using them directly. After finalization, all the ops table are identical before and after the patch except for setting .irq_handler to ata_interrupt in drivers which didn't use to. The .irq_handler doesn't have any actual effect and the field will soon be removed by later patch. * sata_sx4 is still using old style EH and currently doesn't take advantage of ops inheritance. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 04:22:49 +01:00
.cable_detect = hpt3x2n_cable_detect,
.set_piomode = hpt3x2n_set_piomode,
.set_dmamode = hpt3x2n_set_dmamode,
libata: make reset related methods proper port operations Currently reset methods are not specified directly in the ata_port_operations table. If a LLD wants to use custom reset methods, it should construct and use a error_handler which uses those reset methods. It's done this way for two reasons. First, the ops table already contained too many methods and adding four more of them would noticeably increase the amount of necessary boilerplate code all over low level drivers. Second, as ->error_handler uses those reset methods, it can get confusing. ie. By overriding ->error_handler, those reset ops can be made useless making layering a bit hazy. Now that ops table uses inheritance, the first problem doesn't exist anymore. The second isn't completely solved but is relieved by providing default values - most drivers can just override what it has implemented and don't have to concern itself about higher level callbacks. In fact, there currently is no driver which actually modifies error handling behavior. Drivers which override ->error_handler just wraps the standard error handler only to prepare the controller for EH. I don't think making ops layering strict has any noticeable benefit. This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and their PMP counterparts propoer ops. Default ops are provided in the base ops tables and drivers are converted to override individual reset methods instead of creating custom error_handler. * ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs aren't accessible. sata_promise doesn't need to use separate error_handlers for PATA and SATA anymore. * softreset is broken for sata_inic162x and sata_sx4. As libata now always prefers hardreset, this doesn't really matter but the ops are forced to NULL using ATA_OP_NULL for documentation purpose. * pata_hpt374 needs to use different prereset for the first and second PCI functions. This used to be done by branching from hpt374_error_handler(). The proper way to do this is to use separate ops and port_info tables for each function. Converted. Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-03-25 04:22:50 +01:00
.prereset = hpt3x2n_pre_reset,
};
/**
* hpt3xn_calibrate_dpll - Calibrate the DPLL loop
* @dev: PCI device
*
* Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this
* succeeds
*/
static int hpt3xn_calibrate_dpll(struct pci_dev *dev)
{
u8 reg5b;
u32 reg5c;
int tries;
for(tries = 0; tries < 0x5000; tries++) {
udelay(50);
pci_read_config_byte(dev, 0x5b, &reg5b);
if (reg5b & 0x80) {
/* See if it stays set */
for(tries = 0; tries < 0x1000; tries ++) {
pci_read_config_byte(dev, 0x5b, &reg5b);
/* Failed ? */
if ((reg5b & 0x80) == 0)
return 0;
}
/* Turn off tuning, we have the DPLL set */
pci_read_config_dword(dev, 0x5c, &reg5c);
pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100);
return 1;
}
}
/* Never went stable */
return 0;
}
static int hpt3x2n_pci_clock(struct pci_dev *pdev)
{
unsigned long freq;
u32 fcnt;
unsigned long iobase = pci_resource_start(pdev, 4);
fcnt = inl(iobase + 0x90); /* Not PCI readable for some chips */
if ((fcnt >> 12) != 0xABCDE) {
printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
return 33; /* Not BIOS set */
}
fcnt &= 0x1FF;
freq = (fcnt * 77) / 192;
/* Clamp to bands */
if (freq < 40)
return 33;
if (freq < 45)
return 40;
if (freq < 55)
return 50;
return 66;
}
/**
* hpt3x2n_init_one - Initialise an HPT37X/302
* @dev: PCI device
* @id: Entry in match table
*
* Initialise an HPT3x2n device. There are some interesting complications
* here. Firstly the chip may report 366 and be one of several variants.
* Secondly all the timings depend on the clock for the chip which we must
* detect and look up
*
* This is the known chip mappings. It may be missing a couple of later
* releases.
*
* Chip version PCI Rev Notes
* HPT372 4 (HPT366) 5 Other driver
* HPT372N 4 (HPT366) 6 UDMA133
* HPT372 5 (HPT372) 1 Other driver
* HPT372N 5 (HPT372) 2 UDMA133
* HPT302 6 (HPT302) * Other driver
* HPT302N 6 (HPT302) > 1 UDMA133
* HPT371 7 (HPT371) * Other driver
* HPT371N 7 (HPT371) > 1 UDMA133
* HPT374 8 (HPT374) * Other driver
* HPT372N 9 (HPT372N) * UDMA133
*
* (1) UDMA133 support depends on the bus clock
*
* To pin down HPT371N
*/
static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
/* HPT372N and friends - UDMA133 */
libata: clean up SFF init mess The intention of using port_mask in SFF init helpers was to eventually support exoctic configurations such as combination of legacy and native port on the same controller. This never became actually necessary and the related code always has been subtly broken one way or the other. Now that new init model is in place, there is no reason to make common helpers capable of handling all corner cases. Exotic cases can simply dealt within LLDs as necessary. This patch removes port_mask handling in SFF init helpers. SFF init helpers don't take n_ports argument and interpret it into port_mask anymore. All information is carried via port_info. n_ports argument is dropped and always two ports are allocated. LLD can tell SFF to skip certain port by marking it dummy. Note that SFF code has been treating unuvailable ports this way for a long time until recent breakage fix from Linus and is consistent with how other drivers handle with unavailable ports. This fixes 1-port legacy host handling still broken after the recent native mode fix and simplifies SFF init logic. The following changes are made... * ata_pci_init_native_host() and ata_init_legacy_host() both now try to initialized whatever they can and mark failed ports dummy. They return 0 if any port is successfully initialized. * ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't take n_ports argument. All info should be specified via port_info array. Always two ports are allocated. * ata_pci_init_bmdma() exported to be used by LLDs in exotic cases. * port_info handling in all LLDs are standardized - all port_info arrays are const stack variable named ppi. Unless the second port is different from the first, its port_info is specified as NULL (tells libata that it's identical to the last non-NULL port_info). * pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an on-stack copy instead as ata_piix does. * pata_uli: It has 4 ports instead of 2. Don't use ata_pci_prepare_native_host(). Allocate the host explicitly and use init helpers. It's simple enough. Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-04 12:43:58 +02:00
static const struct ata_port_info info = {
.flags = ATA_FLAG_SLAVE_POSS,
.pio_mask = ATA_PIO4,
.mwdma_mask = ATA_MWDMA2,
.udma_mask = ATA_UDMA6,
.port_ops = &hpt3x2n_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
u8 rev = dev->revision;
u8 irqmask;
unsigned int pci_mhz;
unsigned int f_low, f_high;
int adjust;
unsigned long iobase = pci_resource_start(dev, 4);
void *hpriv = (void *)USE_DPLL;
int rc;
rc = pcim_enable_device(dev);
if (rc)
return rc;
switch(dev->device) {
case PCI_DEVICE_ID_TTI_HPT366:
if (rev < 6)
return -ENODEV;
break;
case PCI_DEVICE_ID_TTI_HPT371:
if (rev < 2)
return -ENODEV;
/* 371N if rev > 1 */
break;
case PCI_DEVICE_ID_TTI_HPT372:
/* 372N if rev >= 2*/
if (rev < 2)
return -ENODEV;
break;
case PCI_DEVICE_ID_TTI_HPT302:
if (rev < 2)
return -ENODEV;
break;
case PCI_DEVICE_ID_TTI_HPT372N:
break;
default:
printk(KERN_ERR "pata_hpt3x2n: PCI table is bogus please report (%d).\n", dev->device);
return -ENODEV;
}
/* Ok so this is a chip we support */
pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
pci_read_config_byte(dev, 0x5A, &irqmask);
irqmask &= ~0x10;
pci_write_config_byte(dev, 0x5a, irqmask);
/*
* HPT371 chips physically have only one channel, the secondary one,
* but the primary channel registers do exist! Go figure...
* So, we manually disable the non-existing channel here
* (if the BIOS hasn't done this already).
*/
if (dev->device == PCI_DEVICE_ID_TTI_HPT371) {
u8 mcr1;
pci_read_config_byte(dev, 0x50, &mcr1);
mcr1 &= ~0x04;
pci_write_config_byte(dev, 0x50, mcr1);
}
/* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
50 for UDMA100. Right now we always use 66 */
pci_mhz = hpt3x2n_pci_clock(dev);
f_low = (pci_mhz * 48) / 66; /* PCI Mhz for 66Mhz DPLL */
f_high = f_low + 2; /* Tolerance */
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
/* PLL clock */
pci_write_config_byte(dev, 0x5B, 0x21);
/* Unlike the 37x we don't try jiggling the frequency */
for(adjust = 0; adjust < 8; adjust++) {
if (hpt3xn_calibrate_dpll(dev))
break;
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
}
if (adjust == 8) {
printk(KERN_ERR "pata_hpt3x2n: DPLL did not stabilize!\n");
return -ENODEV;
}
printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using 66MHz DPLL.\n",
pci_mhz);
/* Set our private data up. We only need a few flags so we use
it directly */
if (pci_mhz > 60)
hpriv = (void *)(PCI66 | USE_DPLL);
/*
* On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
* the MISC. register to stretch the UltraDMA Tss timing.
* NOTE: This register is only writeable via I/O space.
*/
if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
/* Now kick off ATA set up */
return ata_pci_bmdma_init_one(dev, ppi, &hpt3x2n_sht, hpriv, 0);
}
static const struct pci_device_id hpt3x2n[] = {
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), },
{ },
};
static struct pci_driver hpt3x2n_pci_driver = {
.name = DRV_NAME,
.id_table = hpt3x2n,
.probe = hpt3x2n_init_one,
.remove = ata_pci_remove_one
};
static int __init hpt3x2n_init(void)
{
return pci_register_driver(&hpt3x2n_pci_driver);
}
static void __exit hpt3x2n_exit(void)
{
pci_unregister_driver(&hpt3x2n_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, hpt3x2n);
MODULE_VERSION(DRV_VERSION);
module_init(hpt3x2n_init);
module_exit(hpt3x2n_exit);