linux/arch/arm/kernel/xscale-cp0.c

180 lines
3.9 KiB
C
Raw Normal View History

[ARM] 3881/4: xscale: clean up cp0/cp1 handling XScale cores either have a DSP coprocessor (which contains a single 40 bit accumulator register), or an iWMMXt coprocessor (which contains eight 64 bit registers.) Because of the small amount of state in the DSP coprocessor, access to the DSP coprocessor (CP0) is always enabled, and DSP context switching is done unconditionally on every task switch. Access to the iWMMXt coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is first issued, and iWMMXt context switching is done lazily. CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will have iWMMXt support', but boards are supposed to select this config symbol by hand, and at least one pxa27x board doesn't get this right, so on that board, proc-xscale.S will incorrectly assume that we have a DSP coprocessor, enable CP0 on boot, and we will then only save the first iWMMXt register (wR0) on context switches, which is Bad. This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on might have iWMMXt support, and we will enable iWMMXt context switching if it does.' This means that with this patch, running a CONFIG_IWMMXT=n kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt state over context switches, and running a CONFIG_IWMMXT=y kernel on a non-iWMMXt capable CPU will still do DSP context save/restore. These changes should make iWMMXt work on PXA3xx, and as a side effect, enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined), as well as setting and using HWCAP_IWMMXT properly. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-12-03 18:51:14 +01:00
/*
* linux/arch/arm/kernel/xscale-cp0.c
*
* XScale DSP and iWMMXt coprocessor context switching and handling
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/module.h>
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/signal.h>
#include <linux/sched.h>
#include <linux/init.h>
#include <linux/io.h>
[ARM] 3881/4: xscale: clean up cp0/cp1 handling XScale cores either have a DSP coprocessor (which contains a single 40 bit accumulator register), or an iWMMXt coprocessor (which contains eight 64 bit registers.) Because of the small amount of state in the DSP coprocessor, access to the DSP coprocessor (CP0) is always enabled, and DSP context switching is done unconditionally on every task switch. Access to the iWMMXt coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is first issued, and iWMMXt context switching is done lazily. CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will have iWMMXt support', but boards are supposed to select this config symbol by hand, and at least one pxa27x board doesn't get this right, so on that board, proc-xscale.S will incorrectly assume that we have a DSP coprocessor, enable CP0 on boot, and we will then only save the first iWMMXt register (wR0) on context switches, which is Bad. This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on might have iWMMXt support, and we will enable iWMMXt context switching if it does.' This means that with this patch, running a CONFIG_IWMMXT=n kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt state over context switches, and running a CONFIG_IWMMXT=y kernel on a non-iWMMXt capable CPU will still do DSP context save/restore. These changes should make iWMMXt work on PXA3xx, and as a side effect, enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined), as well as setting and using HWCAP_IWMMXT properly. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-12-03 18:51:14 +01:00
#include <asm/thread_notify.h>
static inline void dsp_save_state(u32 *state)
{
__asm__ __volatile__ (
"mrrc p0, 0, %0, %1, c0\n"
: "=r" (state[0]), "=r" (state[1]));
}
static inline void dsp_load_state(u32 *state)
{
__asm__ __volatile__ (
"mcrr p0, 0, %0, %1, c0\n"
: : "r" (state[0]), "r" (state[1]));
}
static int dsp_do(struct notifier_block *self, unsigned long cmd, void *t)
{
struct thread_info *thread = t;
switch (cmd) {
case THREAD_NOTIFY_FLUSH:
thread->cpu_context.extra[0] = 0;
thread->cpu_context.extra[1] = 0;
break;
case THREAD_NOTIFY_SWITCH:
dsp_save_state(current_thread_info()->cpu_context.extra);
dsp_load_state(thread->cpu_context.extra);
break;
}
return NOTIFY_DONE;
}
static struct notifier_block dsp_notifier_block = {
.notifier_call = dsp_do,
};
#ifdef CONFIG_IWMMXT
static int iwmmxt_do(struct notifier_block *self, unsigned long cmd, void *t)
{
struct thread_info *thread = t;
switch (cmd) {
case THREAD_NOTIFY_FLUSH:
/*
* flush_thread() zeroes thread->fpstate, so no need
* to do anything here.
*
* FALLTHROUGH: Ensure we don't try to overwrite our newly
* initialised state information on the first fault.
*/
case THREAD_NOTIFY_EXIT:
[ARM] 3881/4: xscale: clean up cp0/cp1 handling XScale cores either have a DSP coprocessor (which contains a single 40 bit accumulator register), or an iWMMXt coprocessor (which contains eight 64 bit registers.) Because of the small amount of state in the DSP coprocessor, access to the DSP coprocessor (CP0) is always enabled, and DSP context switching is done unconditionally on every task switch. Access to the iWMMXt coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is first issued, and iWMMXt context switching is done lazily. CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will have iWMMXt support', but boards are supposed to select this config symbol by hand, and at least one pxa27x board doesn't get this right, so on that board, proc-xscale.S will incorrectly assume that we have a DSP coprocessor, enable CP0 on boot, and we will then only save the first iWMMXt register (wR0) on context switches, which is Bad. This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on might have iWMMXt support, and we will enable iWMMXt context switching if it does.' This means that with this patch, running a CONFIG_IWMMXT=n kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt state over context switches, and running a CONFIG_IWMMXT=y kernel on a non-iWMMXt capable CPU will still do DSP context save/restore. These changes should make iWMMXt work on PXA3xx, and as a side effect, enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined), as well as setting and using HWCAP_IWMMXT properly. Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-12-03 18:51:14 +01:00
iwmmxt_task_release(thread);
break;
case THREAD_NOTIFY_SWITCH:
iwmmxt_task_switch(thread);
break;
}
return NOTIFY_DONE;
}
static struct notifier_block iwmmxt_notifier_block = {
.notifier_call = iwmmxt_do,
};
#endif
static u32 __init xscale_cp_access_read(void)
{
u32 value;
__asm__ __volatile__ (
"mrc p15, 0, %0, c15, c1, 0\n\t"
: "=r" (value));
return value;
}
static void __init xscale_cp_access_write(u32 value)
{
u32 temp;
__asm__ __volatile__ (
"mcr p15, 0, %1, c15, c1, 0\n\t"
"mrc p15, 0, %0, c15, c1, 0\n\t"
"mov %0, %0\n\t"
"sub pc, pc, #4\n\t"
: "=r" (temp) : "r" (value));
}
/*
* Detect whether we have a MAC coprocessor (40 bit register) or an
* iWMMXt coprocessor (64 bit registers) by loading 00000100:00000000
* into a coprocessor register and reading it back, and checking
* whether the upper word survived intact.
*/
static int __init cpu_has_iwmmxt(void)
{
u32 lo;
u32 hi;
/*
* This sequence is interpreted by the DSP coprocessor as:
* mar acc0, %2, %3
* mra %0, %1, acc0
*
* And by the iWMMXt coprocessor as:
* tmcrr wR0, %2, %3
* tmrrc %0, %1, wR0
*/
__asm__ __volatile__ (
"mcrr p0, 0, %2, %3, c0\n"
"mrrc p0, 0, %0, %1, c0\n"
: "=r" (lo), "=r" (hi)
: "r" (0), "r" (0x100));
return !!hi;
}
/*
* If we detect that the CPU has iWMMXt (and CONFIG_IWMMXT=y), we
* disable CP0/CP1 on boot, and let call_fpe() and the iWMMXt lazy
* switch code handle iWMMXt context switching. If on the other
* hand the CPU has a DSP coprocessor, we keep access to CP0 enabled
* all the time, and save/restore acc0 on context switch in non-lazy
* fashion.
*/
static int __init xscale_cp0_init(void)
{
u32 cp_access;
cp_access = xscale_cp_access_read() & ~3;
xscale_cp_access_write(cp_access | 1);
if (cpu_has_iwmmxt()) {
#ifndef CONFIG_IWMMXT
printk(KERN_WARNING "CAUTION: XScale iWMMXt coprocessor "
"detected, but kernel support is missing.\n");
#else
printk(KERN_INFO "XScale iWMMXt coprocessor detected.\n");
elf_hwcap |= HWCAP_IWMMXT;
thread_register_notifier(&iwmmxt_notifier_block);
#endif
} else {
printk(KERN_INFO "XScale DSP coprocessor detected.\n");
thread_register_notifier(&dsp_notifier_block);
cp_access |= 1;
}
xscale_cp_access_write(cp_access);
return 0;
}
late_initcall(xscale_cp0_init);