diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt new file mode 100644 index 000000000000..435f1bcca341 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt @@ -0,0 +1,65 @@ +Broadcom STB "UPG GIO" GPIO controller + +The controller's registers are organized as sets of eight 32-bit +registers with each set controlling a bank of up to 32 pins. A single +interrupt is shared for all of the banks handled by the controller. + +Required properties: + +- compatible: + Must be "brcm,brcmstb-gpio" + +- reg: + Define the base and range of the I/O address space containing + the brcmstb GPIO controller registers + +- #gpio-cells: + Should be <2>. The first cell is the pin number (within the controller's + pin space), and the second is used for the following: + bit[0]: polarity (0 for active-high, 1 for active-low) + +- gpio-controller: + Specifies that the node is a GPIO controller. + +- brcm,gpio-bank-widths: + Number of GPIO lines for each bank. Number of elements must + correspond to number of banks suggested by the 'reg' property. + +Optional properties: + +- interrupts: + The interrupt shared by all GPIO lines for this controller. + +- interrupt-parent: + phandle of the parent interrupt controller + +- #interrupt-cells: + Should be <2>. The first cell is the GPIO number, the second should specify + flags. The following subset of flags is supported: + - bits[3:0] trigger type and level flags + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered + 4 = active high level-sensitive + 8 = active low level-sensitive + Valid combinations are 1, 2, 3, 4, 8. + See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +- interrupt-controller: + Marks the device node as an interrupt controller + +- interrupt-names: + The name of the IRQ resource used by this controller + +Example: + upg_gio: gpio@f040a700 { + #gpio-cells = <0x2>; + #interrupt-cells = <0x2>; + compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; + gpio-controller; + interrupt-controller; + reg = <0xf040a700 0x80>; + interrupt-parent = <0xf>; + interrupts = <0x6>; + interrupt-names = "upg_gio"; + brcm,gpio-bank-widths = <0x20 0x20 0x20 0x18>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt new file mode 100644 index 000000000000..abf4db736c6e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt @@ -0,0 +1,21 @@ +Axis ETRAX FS General I/O controller bindings + +Required properties: + +- compatible: + - "axis,etraxfs-gio" +- reg: Physical base address and length of the controller's registers. +- #gpio-cells: Should be 3 + - The first cell is the gpio offset number. + - The second cell is reserved and is currently unused. + - The third cell is the port number (hex). +- gpio-controller: Marks the device node as a GPIO controller. + +Example: + + gio: gpio@b001a000 { + compatible = "axis,etraxfs-gio"; + reg = <0xb001a000 0x1000>; + gpio-controller; + #gpio-cells = <3>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt new file mode 100644 index 000000000000..262ee4ddf2cb --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt @@ -0,0 +1,47 @@ +Netlogic XLP Family GPIO +======================== + +This GPIO driver is used for following Netlogic XLP SoCs: + XLP832, XLP316, XLP208, XLP980, XLP532 + +Required properties: +------------------- + +- compatible: Should be one of the following: + - "netlogic,xlp832-gpio": For Netlogic XLP832 + - "netlogic,xlp316-gpio": For Netlogic XLP316 + - "netlogic,xlp208-gpio": For Netlogic XLP208 + - "netlogic,xlp980-gpio": For Netlogic XLP980 + - "netlogic,xlp532-gpio": For Netlogic XLP532 +- reg: Physical base address and length of the controller's registers. +- #gpio-cells: Should be two. The first cell is the pin number and the second + cell is used to specify optional parameters (currently unused). +- gpio-controller: Marks the device node as a GPIO controller. +- nr-gpios: Number of GPIO pins supported by the controller. +- interrupt-cells: Should be two. The first cell is the GPIO Number. The + second cell is used to specify flags. The following subset of flags is + supported: + - trigger type: + 1 = low to high edge triggered. + 2 = high to low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. +- interrupts: Interrupt number for this device. +- interrupt-parent: phandle of the parent interrupt controller. +- interrupt-controller: Identifies the node as an interrupt controller. + +Example: + + gpio: xlp_gpio@34000 { + compatible = "netlogic,xlp316-gpio"; + reg = <0 0x34100 0x1000 + 0 0x35100 0x1000>; + #gpio-cells = <2>; + gpio-controller; + nr-gpios = <57>; + + #interrupt-cells = <2>; + interrupt-parent = <&pic>; + interrupts = <39>; + interrupt-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt index 986371a4be2c..db4c6a663c03 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt @@ -6,7 +6,7 @@ Required properties: - First cell is the GPIO line number - Second cell is used to specify optional parameters (unused) -- compatible : Should be "xlnx,zynq-gpio-1.0" +- compatible : Should be "xlnx,zynq-gpio-1.0" or "xlnx,zynqmp-gpio-1.0" - clocks : Clock specifier (see clock bindings for details) - gpio-controller : Marks the device node as a GPIO controller. - interrupts : Interrupt specifier (see interrupt bindings for diff --git a/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt new file mode 100644 index 000000000000..eb7cdd69e10b --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt @@ -0,0 +1,39 @@ +NXP LPC18xx/43xx GPIO controller Device Tree Bindings +----------------------------------------------------- + +Required properties: +- compatible : Should be "nxp,lpc1850-gpio" +- reg : Address and length of the register set for the device +- clocks : Clock specifier (see clock bindings for details) +- gpio-controller : Marks the device node as a GPIO controller. +- #gpio-cells : Should be two + - First cell is the GPIO line number + - Second cell is used to specify polarity + +Optional properties: +- gpio-ranges : Mapping between GPIO and pinctrl + +Example: +#define LPC_GPIO(port, pin) (port * 32 + pin) +#define LPC_PIN(port, pin) (0x##port * 32 + pin) + +gpio: gpio@400f4000 { + compatible = "nxp,lpc1850-gpio"; + reg = <0x400f4000 0x4000>; + clocks = <&ccu1 CLK_CPU_GPIO>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pinctrl LPC_GPIO(0,0) LPC_PIN(0,0) 2>, + ... + <&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5) 7>; +}; + +gpio_joystick { + compatible = "gpio-keys-polled"; + ... + + button@0 { + ... + gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/gpio/consumer.txt b/Documentation/gpio/consumer.txt index c21c1313f09e..bbc8b5888b80 100644 --- a/Documentation/gpio/consumer.txt +++ b/Documentation/gpio/consumer.txt @@ -241,18 +241,18 @@ Set multiple GPIO outputs with a single function call ----------------------------------------------------- The following functions set the output values of an array of GPIOs: - void gpiod_set_array(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) - void gpiod_set_raw_array(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) - void gpiod_set_array_cansleep(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) - void gpiod_set_raw_array_cansleep(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) + void gpiod_set_array_value(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) + void gpiod_set_raw_array_value(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) + void gpiod_set_array_value_cansleep(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) + void gpiod_set_raw_array_value_cansleep(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) The array can be an arbitrary set of GPIOs. The functions will try to set GPIOs belonging to the same bank or chip simultaneously if supported by the @@ -271,8 +271,8 @@ matches the desired group of GPIOs, those GPIOs can be set by simply using the struct gpio_descs returned by gpiod_get_array(): struct gpio_descs *my_gpio_descs = gpiod_get_array(...); - gpiod_set_array(my_gpio_descs->ndescs, my_gpio_descs->desc, - my_gpio_values); + gpiod_set_array_value(my_gpio_descs->ndescs, my_gpio_descs->desc, + my_gpio_values); It is also possible to set a completely arbitrary array of descriptors. The descriptors may be obtained using any combination of gpiod_get() and diff --git a/Documentation/gpio/gpio-legacy.txt b/Documentation/gpio/gpio-legacy.txt index 6f83fa965b4b..79ab5648d69b 100644 --- a/Documentation/gpio/gpio-legacy.txt +++ b/Documentation/gpio/gpio-legacy.txt @@ -751,9 +751,6 @@ requested using gpio_request(): int gpio_export_link(struct device *dev, const char *name, unsigned gpio) - /* change the polarity of a GPIO node in sysfs */ - int gpio_sysfs_set_active_low(unsigned gpio, int value); - After a kernel driver requests a GPIO, it may only be made available in the sysfs interface by gpio_export(). The driver can control whether the signal direction may change. This helps drivers prevent userspace code @@ -767,9 +764,3 @@ After the GPIO has been exported, gpio_export_link() allows creating symlinks from elsewhere in sysfs to the GPIO sysfs node. Drivers can use this to provide the interface under their own device in sysfs with a descriptive name. - -Drivers can use gpio_sysfs_set_active_low() to hide GPIO line polarity -differences between boards from user space. This only affects the -sysfs interface. Polarity change can be done both before and after -gpio_export(), and previously enabled poll(2) support for either -rising or falling edge will be reconfigured to follow this setting. diff --git a/Documentation/gpio/sysfs.txt b/Documentation/gpio/sysfs.txt index c2c3a97f8ff7..535b6a8a7a7c 100644 --- a/Documentation/gpio/sysfs.txt +++ b/Documentation/gpio/sysfs.txt @@ -132,9 +132,6 @@ requested using gpio_request(): int gpiod_export_link(struct device *dev, const char *name, struct gpio_desc *desc); - /* change the polarity of a GPIO node in sysfs */ - int gpiod_sysfs_set_active_low(struct gpio_desc *desc, int value); - After a kernel driver requests a GPIO, it may only be made available in the sysfs interface by gpiod_export(). The driver can control whether the signal direction may change. This helps drivers prevent userspace code @@ -148,8 +145,3 @@ After the GPIO has been exported, gpiod_export_link() allows creating symlinks from elsewhere in sysfs to the GPIO sysfs node. Drivers can use this to provide the interface under their own device in sysfs with a descriptive name. - -Drivers can use gpiod_sysfs_set_active_low() to hide GPIO line polarity -differences between boards from user space. Polarity change can be done both -before and after gpiod_export(), and previously enabled poll(2) support for -either rising or falling edge will be reconfigured to follow this setting. diff --git a/Documentation/zh_CN/gpio.txt b/Documentation/zh_CN/gpio.txt index d5b8f01833f4..bce972521065 100644 --- a/Documentation/zh_CN/gpio.txt +++ b/Documentation/zh_CN/gpio.txt @@ -638,9 +638,6 @@ GPIO 控制器的路径类似 /sys/class/gpio/gpiochip42/ (对于从#42 GPIO int gpio_export_link(struct device *dev, const char *name, unsigned gpio) - /* 改变 sysfs 中的一个 GPIO 节点的极性 */ - int gpio_sysfs_set_active_low(unsigned gpio, int value); - 在一个内核驱动申请一个 GPIO 之后，它可以通过 gpio_export()使其在 sysfs 接口中可见。该驱动可以控制信号方向是否可修改。这有助于防止用户空间代码无意间 破坏重要的系统状态。 @@ -651,8 +648,3 @@ GPIO 控制器的路径类似 /sys/class/gpio/gpiochip42/ (对于从#42 GPIO 在 GPIO 被导出之后，gpio_export_link()允许在 sysfs 文件系统的任何地方 创建一个到这个 GPIO sysfs 节点的符号链接。这样驱动就可以通过一个描述性的 名字，在 sysfs 中他们所拥有的设备下提供一个(到这个 GPIO sysfs 节点的)接口。 - -驱动可以使用 gpio_sysfs_set_active_low() 来在用户空间隐藏电路板之间 -GPIO 线的极性差异。这个仅对 sysfs 接口起作用。极性的改变可以在 gpio_export() -前后进行,且之前使能的轮询操作(poll(2))支持(上升或下降沿)将会被重新配置来遵循 -这个设置。 diff --git a/MAINTAINERS b/MAINTAINERS index 4f1e79b52cc5..8de3a7b0bf2d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2250,6 +2250,13 @@ N: bcm9583* N: bcm583* N: bcm113* +BROADCOM BRCMSTB GPIO DRIVER +M: Gregory Fong +L: bcm-kernel-feedback-list@broadcom.com> +S: Supported +F: drivers/gpio/gpio-brcmstb.c +F: Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt + BROADCOM KONA GPIO DRIVER M: Ray Jui L: bcm-kernel-feedback-list@broadcom.com diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index caefe806db5e..8f1fe739c985 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -126,6 +126,14 @@ config GPIO_BCM_KONA help Turn on GPIO support for Broadcom "Kona" chips. +config GPIO_BRCMSTB + tristate "BRCMSTB GPIO support" + default y if ARCH_BRCMSTB + depends on OF_GPIO && (ARCH_BRCMSTB || COMPILE_TEST) + select GPIO_GENERIC + help + Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs. + config GPIO_CLPS711X tristate "CLPS711X GPIO support" depends on ARCH_CLPS711X || COMPILE_TEST @@ -159,6 +167,14 @@ config GPIO_EP93XX depends on ARCH_EP93XX select GPIO_GENERIC +config GPIO_ETRAXFS + bool "Axis ETRAX FS General I/O" + depends on CRIS || COMPILE_TEST + depends on OF + select GPIO_GENERIC + help + Say yes here to support the GPIO controller on Axis ETRAX FS SoCs. + config GPIO_F7188X tristate "F71869, F71869A, F71882FG and F71889F GPIO support" depends on X86 @@ -230,6 +246,14 @@ config GPIO_LOONGSON help driver for GPIO functionality on Loongson-2F/3A/3B processors. +config GPIO_LPC18XX + bool "NXP LPC18XX/43XX GPIO support" + default y if ARCH_LPC18XX + depends on OF_GPIO && (ARCH_LPC18XX || COMPILE_TEST) + help + Select this option to enable GPIO driver for + NXP LPC18XX/43XX devices. + config GPIO_LYNXPOINT tristate "Intel Lynxpoint GPIO support" depends on ACPI && X86 @@ -308,7 +332,7 @@ config GPIO_OCTEON family of SOCs. config GPIO_OMAP - bool "TI OMAP GPIO support" if COMPILE_TEST && !ARCH_OMAP2PLUS + tristate "TI OMAP GPIO support" if ARCH_OMAP2PLUS || COMPILE_TEST default y if ARCH_OMAP depends on ARM select GENERIC_IRQ_CHIP @@ -488,6 +512,17 @@ config GPIO_XILINX help Say yes here to support the Xilinx FPGA GPIO device +config GPIO_XLP + tristate "Netlogic XLP GPIO support" + depends on CPU_XLP + select GPIOLIB_IRQCHIP + help + This driver provides support for GPIO interface on Netlogic XLP MIPS64 + SoCs. Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, + XLP9XX and XLP5XX. + + If unsure, say N. + config GPIO_XTENSA bool "Xtensa GPIO32 support" depends on XTENSA @@ -505,7 +540,7 @@ config GPIO_ZEVIO config GPIO_ZYNQ tristate "Xilinx Zynq GPIO support" - depends on ARCH_ZYNQ + depends on ARCH_ZYNQ || ARCH_ZYNQMP select GPIOLIB_IRQCHIP help Say yes here to support Xilinx Zynq GPIO controller. diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index f71bb971329c..f82cd678ce08 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -21,6 +21,7 @@ obj-$(CONFIG_GPIO_ALTERA) += gpio-altera.o obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o obj-$(CONFIG_GPIO_BCM_KONA) += gpio-bcm-kona.o +obj-$(CONFIG_GPIO_BRCMSTB) += gpio-brcmstb.o obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o obj-$(CONFIG_GPIO_CLPS711X) += gpio-clps711x.o obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o @@ -32,6 +33,7 @@ obj-$(CONFIG_GPIO_DLN2) += gpio-dln2.o obj-$(CONFIG_GPIO_DWAPB) += gpio-dwapb.o obj-$(CONFIG_GPIO_EM) += gpio-em.o obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o +obj-$(CONFIG_GPIO_ETRAXFS) += gpio-etraxfs.o obj-$(CONFIG_GPIO_F7188X) += gpio-f7188x.o obj-$(CONFIG_GPIO_GE_FPGA) += gpio-ge.o obj-$(CONFIG_GPIO_GRGPIO) += gpio-grgpio.o @@ -44,6 +46,7 @@ obj-$(CONFIG_ARCH_KS8695) += gpio-ks8695.o obj-$(CONFIG_GPIO_INTEL_MID) += gpio-intel-mid.o obj-$(CONFIG_GPIO_LOONGSON) += gpio-loongson.o obj-$(CONFIG_GPIO_LP3943) += gpio-lp3943.o +obj-$(CONFIG_GPIO_LPC18XX) += gpio-lpc18xx.o obj-$(CONFIG_ARCH_LPC32XX) += gpio-lpc32xx.o obj-$(CONFIG_GPIO_LYNXPOINT) += gpio-lynxpoint.o obj-$(CONFIG_GPIO_MAX730X) += gpio-max730x.o @@ -109,6 +112,7 @@ obj-$(CONFIG_GPIO_WM8994) += gpio-wm8994.o obj-$(CONFIG_GPIO_XGENE) += gpio-xgene.o obj-$(CONFIG_GPIO_XGENE_SB) += gpio-xgene-sb.o obj-$(CONFIG_GPIO_XILINX) += gpio-xilinx.o +obj-$(CONFIG_GPIO_XLP) += gpio-xlp.o obj-$(CONFIG_GPIO_XTENSA) += gpio-xtensa.o obj-$(CONFIG_GPIO_ZEVIO) += gpio-zevio.o obj-$(CONFIG_GPIO_ZYNQ) += gpio-zynq.o diff --git a/drivers/gpio/gpio-altera.c b/drivers/gpio/gpio-altera.c index 449fb46cb8a0..0f3d336d6303 100644 --- a/drivers/gpio/gpio-altera.c +++ b/drivers/gpio/gpio-altera.c @@ -107,7 +107,8 @@ static int altera_gpio_irq_set_type(struct irq_data *d, return -EINVAL; } -static unsigned int altera_gpio_irq_startup(struct irq_data *d) { +static unsigned int altera_gpio_irq_startup(struct irq_data *d) +{ altera_gpio_irq_unmask(d); return 0; diff --git a/drivers/gpio/gpio-bcm-kona.c b/drivers/gpio/gpio-bcm-kona.c index b164ce837b43..a6e79225886d 100644 --- a/drivers/gpio/gpio-bcm-kona.c +++ b/drivers/gpio/gpio-bcm-kona.c @@ -122,6 +122,16 @@ static void bcm_kona_gpio_unlock_gpio(struct bcm_kona_gpio *kona_gpio, spin_unlock_irqrestore(&kona_gpio->lock, flags); } +static int bcm_kona_gpio_get_dir(struct gpio_chip *chip, unsigned gpio) +{ + struct bcm_kona_gpio *kona_gpio = to_kona_gpio(chip); + void __iomem *reg_base = kona_gpio->reg_base; + u32 val; + + val = readl(reg_base + GPIO_CONTROL(gpio)) & GPIO_GPCTR0_IOTR_MASK; + return val ? GPIOF_DIR_IN : GPIOF_DIR_OUT; +} + static void bcm_kona_gpio_set(struct gpio_chip *chip, unsigned gpio, int value) { struct bcm_kona_gpio *kona_gpio; @@ -135,12 +145,8 @@ static void bcm_kona_gpio_set(struct gpio_chip *chip, unsigned gpio, int value) reg_base = kona_gpio->reg_base; spin_lock_irqsave(&kona_gpio->lock, flags); - /* determine the GPIO pin direction */ - val = readl(reg_base + GPIO_CONTROL(gpio)); - val &= GPIO_GPCTR0_IOTR_MASK; - /* this function only applies to output pin */ - if (GPIO_GPCTR0_IOTR_CMD_INPUT == val) + if (bcm_kona_gpio_get_dir(chip, gpio) == GPIOF_DIR_IN) goto out; reg_offset = value ? GPIO_OUT_SET(bank_id) : GPIO_OUT_CLEAR(bank_id); @@ -166,13 +172,12 @@ static int bcm_kona_gpio_get(struct gpio_chip *chip, unsigned gpio) reg_base = kona_gpio->reg_base; spin_lock_irqsave(&kona_gpio->lock, flags); - /* determine the GPIO pin direction */ - val = readl(reg_base + GPIO_CONTROL(gpio)); - val &= GPIO_GPCTR0_IOTR_MASK; + if (bcm_kona_gpio_get_dir(chip, gpio) == GPIOF_DIR_IN) + reg_offset = GPIO_IN_STATUS(bank_id); + else + reg_offset = GPIO_OUT_STATUS(bank_id); /* read the GPIO bank status */ - reg_offset = (GPIO_GPCTR0_IOTR_CMD_INPUT == val) ? - GPIO_IN_STATUS(bank_id) : GPIO_OUT_STATUS(bank_id); val = readl(reg_base + reg_offset); spin_unlock_irqrestore(&kona_gpio->lock, flags); @@ -310,6 +315,7 @@ static struct gpio_chip template_chip = { .owner = THIS_MODULE, .request = bcm_kona_gpio_request, .free = bcm_kona_gpio_free, + .get_direction = bcm_kona_gpio_get_dir, .direction_input = bcm_kona_gpio_direction_input, .get = bcm_kona_gpio_get, .direction_output = bcm_kona_gpio_direction_output, diff --git a/drivers/gpio/gpio-brcmstb.c b/drivers/gpio/gpio-brcmstb.c new file mode 100644 index 000000000000..7a3cb1fa0a76 --- /dev/null +++ b/drivers/gpio/gpio-brcmstb.c @@ -0,0 +1,252 @@ +/* + * Copyright (C) 2015 Broadcom Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include + +#define GIO_BANK_SIZE 0x20 +#define GIO_ODEN(bank) (((bank) * GIO_BANK_SIZE) + 0x00) +#define GIO_DATA(bank) (((bank) * GIO_BANK_SIZE) + 0x04) +#define GIO_IODIR(bank) (((bank) * GIO_BANK_SIZE) + 0x08) +#define GIO_EC(bank) (((bank) * GIO_BANK_SIZE) + 0x0c) +#define GIO_EI(bank) (((bank) * GIO_BANK_SIZE) + 0x10) +#define GIO_MASK(bank) (((bank) * GIO_BANK_SIZE) + 0x14) +#define GIO_LEVEL(bank) (((bank) * GIO_BANK_SIZE) + 0x18) +#define GIO_STAT(bank) (((bank) * GIO_BANK_SIZE) + 0x1c) + +struct brcmstb_gpio_bank { + struct list_head node; + int id; + struct bgpio_chip bgc; + struct brcmstb_gpio_priv *parent_priv; + u32 width; +}; + +struct brcmstb_gpio_priv { + struct list_head bank_list; + void __iomem *reg_base; + int num_banks; + struct platform_device *pdev; + int gpio_base; +}; + +#define MAX_GPIO_PER_BANK 32 +#define GPIO_BANK(gpio) ((gpio) >> 5) +/* assumes MAX_GPIO_PER_BANK is a multiple of 2 */ +#define GPIO_BIT(gpio) ((gpio) & (MAX_GPIO_PER_BANK - 1)) + +static inline struct brcmstb_gpio_bank * +brcmstb_gpio_gc_to_bank(struct gpio_chip *gc) +{ + struct bgpio_chip *bgc = to_bgpio_chip(gc); + return container_of(bgc, struct brcmstb_gpio_bank, bgc); +} + +static inline struct brcmstb_gpio_priv * +brcmstb_gpio_gc_to_priv(struct gpio_chip *gc) +{ + struct brcmstb_gpio_bank *bank = brcmstb_gpio_gc_to_bank(gc); + return bank->parent_priv; +} + +/* Make sure that the number of banks matches up between properties */ +static int brcmstb_gpio_sanity_check_banks(struct device *dev, + struct device_node *np, struct resource *res) +{ + int res_num_banks = resource_size(res) / GIO_BANK_SIZE; + int num_banks = + of_property_count_u32_elems(np, "brcm,gpio-bank-widths"); + + if (res_num_banks != num_banks) { + dev_err(dev, "Mismatch in banks: res had %d, bank-widths had %d\n", + res_num_banks, num_banks); + return -EINVAL; + } else { + return 0; + } +} + +static int brcmstb_gpio_remove(struct platform_device *pdev) +{ + struct brcmstb_gpio_priv *priv = platform_get_drvdata(pdev); + struct list_head *pos; + struct brcmstb_gpio_bank *bank; + int ret = 0; + + list_for_each(pos, &priv->bank_list) { + bank = list_entry(pos, struct brcmstb_gpio_bank, node); + ret = bgpio_remove(&bank->bgc); + if (ret) + dev_err(&pdev->dev, "gpiochip_remove fail in cleanup"); + } + return ret; +} + +static int brcmstb_gpio_of_xlate(struct gpio_chip *gc, + const struct of_phandle_args *gpiospec, u32 *flags) +{ + struct brcmstb_gpio_priv *priv = brcmstb_gpio_gc_to_priv(gc); + struct brcmstb_gpio_bank *bank = brcmstb_gpio_gc_to_bank(gc); + int offset; + + if (gc->of_gpio_n_cells != 2) { + WARN_ON(1); + return -EINVAL; + } + + if (WARN_ON(gpiospec->args_count < gc->of_gpio_n_cells)) + return -EINVAL; + + offset = gpiospec->args[0] - (gc->base - priv->gpio_base); + if (offset >= gc->ngpio) + return -EINVAL; + + if (unlikely(offset >= bank->width)) { + dev_warn_ratelimited(&priv->pdev->dev, + "Received request for invalid GPIO offset %d\n", + gpiospec->args[0]); + } + + if (flags) + *flags = gpiospec->args[1]; + + return offset; +} + +static int brcmstb_gpio_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + void __iomem *reg_base; + struct brcmstb_gpio_priv *priv; + struct resource *res; + struct property *prop; + const __be32 *p; + u32 bank_width; + int err; + static int gpio_base; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + reg_base = devm_ioremap_resource(dev, res); + if (IS_ERR(reg_base)) + return PTR_ERR(reg_base); + + priv->gpio_base = gpio_base; + priv->reg_base = reg_base; + priv->pdev = pdev; + + INIT_LIST_HEAD(&priv->bank_list); + if (brcmstb_gpio_sanity_check_banks(dev, np, res)) + return -EINVAL; + + of_property_for_each_u32(np, "brcm,gpio-bank-widths", prop, p, + bank_width) { + struct brcmstb_gpio_bank *bank; + struct bgpio_chip *bgc; + struct gpio_chip *gc; + + bank = devm_kzalloc(dev, sizeof(*bank), GFP_KERNEL); + if (!bank) { + err = -ENOMEM; + goto fail; + } + + bank->parent_priv = priv; + bank->id = priv->num_banks; + if (bank_width <= 0 || bank_width > MAX_GPIO_PER_BANK) { + dev_err(dev, "Invalid bank width %d\n", bank_width); + goto fail; + } else { + bank->width = bank_width; + } + + /* + * Regs are 4 bytes wide, have data reg, no set/clear regs, + * and direction bits have 0 = output and 1 = input + */ + bgc = &bank->bgc; + err = bgpio_init(bgc, dev, 4, + reg_base + GIO_DATA(bank->id), + NULL, NULL, NULL, + reg_base + GIO_IODIR(bank->id), 0); + if (err) { + dev_err(dev, "bgpio_init() failed\n"); + goto fail; + } + + gc = &bgc->gc; + gc->of_node = np; + gc->owner = THIS_MODULE; + gc->label = np->full_name; + gc->base = gpio_base; + gc->of_gpio_n_cells = 2; + gc->of_xlate = brcmstb_gpio_of_xlate; + /* not all ngpio lines are valid, will use bank width later */ + gc->ngpio = MAX_GPIO_PER_BANK; + + err = gpiochip_add(gc); + if (err) { + dev_err(dev, "Could not add gpiochip for bank %d\n", + bank->id); + goto fail; + } + gpio_base += gc->ngpio; + dev_dbg(dev, "bank=%d, base=%d, ngpio=%d, width=%d\n", bank->id, + gc->base, gc->ngpio, bank->width); + + /* Everything looks good, so add bank to list */ + list_add(&bank->node, &priv->bank_list); + + priv->num_banks++; + } + + dev_info(dev, "Registered %d banks (GPIO(s): %d-%d)\n", + priv->num_banks, priv->gpio_base, gpio_base - 1); + + platform_set_drvdata(pdev, priv); + + return 0; + +fail: + (void) brcmstb_gpio_remove(pdev); + return err; +} + +static const struct of_device_id brcmstb_gpio_of_match[] = { + { .compatible = "brcm,brcmstb-gpio" }, + {}, +}; + +MODULE_DEVICE_TABLE(of, brcmstb_gpio_of_match); + +static struct platform_driver brcmstb_gpio_driver = { + .driver = { + .name = "brcmstb-gpio", + .of_match_table = brcmstb_gpio_of_match, + }, + .probe = brcmstb_gpio_probe, + .remove = brcmstb_gpio_remove, +}; +module_platform_driver(brcmstb_gpio_driver); + +MODULE_AUTHOR("Gregory Fong"); +MODULE_DESCRIPTION("Driver for Broadcom BRCMSTB SoC UPG GPIO"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/gpio/gpio-crystalcove.c b/drivers/gpio/gpio-crystalcove.c index 91a7ffe83135..fddd204dc9b6 100644 --- a/drivers/gpio/gpio-crystalcove.c +++ b/drivers/gpio/gpio-crystalcove.c @@ -16,6 +16,7 @@ */ #include +#include #include #include #include @@ -94,9 +95,8 @@ static inline int to_reg(int gpio, enum ctrl_register reg_type) { int reg; - if (gpio == 94) { + if (gpio == 94) return GPIOPANELCTL; - } if (reg_type == CTRL_IN) { if (gpio < 8) @@ -255,6 +255,7 @@ static struct irq_chip crystalcove_irqchip = { .irq_set_type = crystalcove_irq_type, .irq_bus_lock = crystalcove_bus_lock, .irq_bus_sync_unlock = crystalcove_bus_sync_unlock, + .flags = IRQCHIP_SKIP_SET_WAKE, }; static irqreturn_t crystalcove_gpio_irq_handler(int irq, void *data) diff --git a/drivers/gpio/gpio-dln2.c b/drivers/gpio/gpio-dln2.c index dbdb4de82c6d..6685712c15cf 100644 --- a/drivers/gpio/gpio-dln2.c +++ b/drivers/gpio/gpio-dln2.c @@ -466,7 +466,6 @@ static int dln2_gpio_probe(struct platform_device *pdev) dln2->gpio.owner = THIS_MODULE; dln2->gpio.base = -1; dln2->gpio.ngpio = pins; - dln2->gpio.exported = true; dln2->gpio.can_sleep = true; dln2->gpio.irq_not_threaded = true; dln2->gpio.set = dln2_gpio_set; diff --git a/drivers/gpio/gpio-etraxfs.c b/drivers/gpio/gpio-etraxfs.c new file mode 100644 index 000000000000..28071f4a5672 --- /dev/null +++ b/drivers/gpio/gpio-etraxfs.c @@ -0,0 +1,176 @@ +#include +#include +#include +#include +#include +#include +#include + +#define ETRAX_FS_rw_pa_dout 0 +#define ETRAX_FS_r_pa_din 4 +#define ETRAX_FS_rw_pa_oe 8 +#define ETRAX_FS_rw_intr_cfg 12 +#define ETRAX_FS_rw_intr_mask 16 +#define ETRAX_FS_rw_ack_intr 20 +#define ETRAX_FS_r_intr 24 +#define ETRAX_FS_rw_pb_dout 32 +#define ETRAX_FS_r_pb_din 36 +#define ETRAX_FS_rw_pb_oe 40 +#define ETRAX_FS_rw_pc_dout 48 +#define ETRAX_FS_r_pc_din 52 +#define ETRAX_FS_rw_pc_oe 56 +#define ETRAX_FS_rw_pd_dout 64 +#define ETRAX_FS_r_pd_din 68 +#define ETRAX_FS_rw_pd_oe 72 +#define ETRAX_FS_rw_pe_dout 80 +#define ETRAX_FS_r_pe_din 84 +#define ETRAX_FS_rw_pe_oe 88 + +struct etraxfs_gpio_port { + const char *label; + unsigned int oe; + unsigned int dout; + unsigned int din; + unsigned int ngpio; +}; + +struct etraxfs_gpio_info { + unsigned int num_ports; + const struct etraxfs_gpio_port *ports; +}; + +static const struct etraxfs_gpio_port etraxfs_gpio_etraxfs_ports[] = { + { + .label = "A", + .ngpio = 8, + .oe = ETRAX_FS_rw_pa_oe, + .dout = ETRAX_FS_rw_pa_dout, + .din = ETRAX_FS_r_pa_din, + }, + { + .label = "B", + .ngpio = 18, + .oe = ETRAX_FS_rw_pb_oe, + .dout = ETRAX_FS_rw_pb_dout, + .din = ETRAX_FS_r_pb_din, + }, + { + .label = "C", + .ngpio = 18, + .oe = ETRAX_FS_rw_pc_oe, + .dout = ETRAX_FS_rw_pc_dout, + .din = ETRAX_FS_r_pc_din, + }, + { + .label = "D", + .ngpio = 18, + .oe = ETRAX_FS_rw_pd_oe, + .dout = ETRAX_FS_rw_pd_dout, + .din = ETRAX_FS_r_pd_din, + }, + { + .label = "E", + .ngpio = 18, + .oe = ETRAX_FS_rw_pe_oe, + .dout = ETRAX_FS_rw_pe_dout, + .din = ETRAX_FS_r_pe_din, + }, +}; + +static const struct etraxfs_gpio_info etraxfs_gpio_etraxfs = { + .num_ports = ARRAY_SIZE(etraxfs_gpio_etraxfs_ports), + .ports = etraxfs_gpio_etraxfs_ports, +}; + +static int etraxfs_gpio_of_xlate(struct gpio_chip *gc, + const struct of_phandle_args *gpiospec, + u32 *flags) +{ + /* + * Port numbers are A to E, and the properties are integers, so we + * specify them as 0xA - 0xE. + */ + if (gc->label[0] - 'A' + 0xA != gpiospec->args[2]) + return -EINVAL; + + return of_gpio_simple_xlate(gc, gpiospec, flags); +} + +static const struct of_device_id etraxfs_gpio_of_table[] = { + { + .compatible = "axis,etraxfs-gio", + .data = &etraxfs_gpio_etraxfs, + }, + {}, +}; + +static int etraxfs_gpio_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + const struct etraxfs_gpio_info *info; + const struct of_device_id *match; + struct bgpio_chip *chips; + struct resource *res; + void __iomem *regs; + int ret; + int i; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + regs = devm_ioremap_resource(dev, res); + if (!regs) + return -ENOMEM; + + match = of_match_node(etraxfs_gpio_of_table, dev->of_node); + if (!match) + return -EINVAL; + + info = match->data; + + chips = devm_kzalloc(dev, sizeof(*chips) * info->num_ports, GFP_KERNEL); + if (!chips) + return -ENOMEM; + + for (i = 0; i < info->num_ports; i++) { + struct bgpio_chip *bgc = &chips[i]; + const struct etraxfs_gpio_port *port = &info->ports[i]; + + ret = bgpio_init(bgc, dev, 4, + regs + port->din, /* dat */ + regs + port->dout, /* set */ + NULL, /* clr */ + regs + port->oe, /* dirout */ + NULL, /* dirin */ + BGPIOF_UNREADABLE_REG_SET); + if (ret) + return ret; + + bgc->gc.ngpio = port->ngpio; + bgc->gc.label = port->label; + + bgc->gc.of_node = dev->of_node; + bgc->gc.of_gpio_n_cells = 3; + bgc->gc.of_xlate = etraxfs_gpio_of_xlate; + + ret = gpiochip_add(&bgc->gc); + if (ret) + dev_err(dev, "Unable to register port %s\n", + bgc->gc.label); + } + + return 0; +} + +static struct platform_driver etraxfs_gpio_driver = { + .driver = { + .name = "etraxfs-gpio", + .of_match_table = of_match_ptr(etraxfs_gpio_of_table), + }, + .probe = etraxfs_gpio_probe, +}; + +static int __init etraxfs_gpio_init(void) +{ + return platform_driver_register(&etraxfs_gpio_driver); +} + +device_initcall(etraxfs_gpio_init); diff --git a/drivers/gpio/gpio-f7188x.c b/drivers/gpio/gpio-f7188x.c index dbda8433c4f7..5e3c4fa67d82 100644 --- a/drivers/gpio/gpio-f7188x.c +++ b/drivers/gpio/gpio-f7188x.c @@ -172,7 +172,7 @@ static struct f7188x_gpio_bank f71869a_gpio_bank[] = { }; static struct f7188x_gpio_bank f71882_gpio_bank[] = { - F7188X_GPIO_BANK(0 , 8, 0xF0), + F7188X_GPIO_BANK(0, 8, 0xF0), F7188X_GPIO_BANK(10, 8, 0xE0), F7188X_GPIO_BANK(20, 8, 0xD0), F7188X_GPIO_BANK(30, 4, 0xC0), @@ -180,7 +180,7 @@ static struct f7188x_gpio_bank f71882_gpio_bank[] = { }; static struct f7188x_gpio_bank f71889_gpio_bank[] = { - F7188X_GPIO_BANK(0 , 7, 0xF0), + F7188X_GPIO_BANK(0, 7, 0xF0), F7188X_GPIO_BANK(10, 7, 0xE0), F7188X_GPIO_BANK(20, 8, 0xD0), F7188X_GPIO_BANK(30, 8, 0xC0), diff --git a/drivers/gpio/gpio-generic.c b/drivers/gpio/gpio-generic.c index b92a690f5765..9bda3727fac1 100644 --- a/drivers/gpio/gpio-generic.c +++ b/drivers/gpio/gpio-generic.c @@ -135,6 +135,17 @@ static unsigned long bgpio_pin2mask_be(struct bgpio_chip *bgc, return 1 << (bgc->bits - 1 - pin); } +static int bgpio_get_set(struct gpio_chip *gc, unsigned int gpio) +{ + struct bgpio_chip *bgc = to_bgpio_chip(gc); + unsigned long pinmask = bgc->pin2mask(bgc, gpio); + + if (bgc->dir & pinmask) + return bgc->read_reg(bgc->reg_set) & pinmask; + else + return bgc->read_reg(bgc->reg_dat) & pinmask; +} + static int bgpio_get(struct gpio_chip *gc, unsigned int gpio) { struct bgpio_chip *bgc = to_bgpio_chip(gc); @@ -416,7 +427,8 @@ static int bgpio_setup_accessors(struct device *dev, static int bgpio_setup_io(struct bgpio_chip *bgc, void __iomem *dat, void __iomem *set, - void __iomem *clr) + void __iomem *clr, + unsigned long flags) { bgc->reg_dat = dat; @@ -437,7 +449,11 @@ static int bgpio_setup_io(struct bgpio_chip *bgc, bgc->gc.set_multiple = bgpio_set_multiple; } - bgc->gc.get = bgpio_get; + if (!(flags & BGPIOF_UNREADABLE_REG_SET) && + (flags & BGPIOF_READ_OUTPUT_REG_SET)) + bgc->gc.get = bgpio_get_set; + else + bgc->gc.get = bgpio_get; return 0; } @@ -500,7 +516,7 @@ int bgpio_init(struct bgpio_chip *bgc, struct device *dev, bgc->gc.ngpio = bgc->bits; bgc->gc.request = bgpio_request; - ret = bgpio_setup_io(bgc, dat, set, clr); + ret = bgpio_setup_io(bgc, dat, set, clr, flags); if (ret) return ret; diff --git a/drivers/gpio/gpio-it8761e.c b/drivers/gpio/gpio-it8761e.c index dadfc245cf09..30a8f24c92c5 100644 --- a/drivers/gpio/gpio-it8761e.c +++ b/drivers/gpio/gpio-it8761e.c @@ -123,7 +123,7 @@ static void it8761e_gpio_set(struct gpio_chip *gc, curr_vals = inb(reg); if (val) - outb(curr_vals | (1 << bit) , reg); + outb(curr_vals | (1 << bit), reg); else outb(curr_vals & ~(1 << bit), reg); diff --git a/drivers/gpio/gpio-lpc18xx.c b/drivers/gpio/gpio-lpc18xx.c new file mode 100644 index 000000000000..eb68603136b0 --- /dev/null +++ b/drivers/gpio/gpio-lpc18xx.c @@ -0,0 +1,180 @@ +/* + * GPIO driver for NXP LPC18xx/43xx. + * + * Copyright (C) 2015 Joachim Eastwood + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +/* LPC18xx GPIO register offsets */ +#define LPC18XX_REG_DIR(n) (0x2000 + n * sizeof(u32)) + +#define LPC18XX_MAX_PORTS 8 +#define LPC18XX_PINS_PER_PORT 32 + +struct lpc18xx_gpio_chip { + struct gpio_chip gpio; + void __iomem *base; + struct clk *clk; + spinlock_t lock; +}; + +static inline struct lpc18xx_gpio_chip *to_lpc18xx_gpio(struct gpio_chip *chip) +{ + return container_of(chip, struct lpc18xx_gpio_chip, gpio); +} + +static int lpc18xx_gpio_request(struct gpio_chip *chip, unsigned offset) +{ + return pinctrl_request_gpio(offset); +} + +static void lpc18xx_gpio_free(struct gpio_chip *chip, unsigned offset) +{ + pinctrl_free_gpio(offset); +} + +static void lpc18xx_gpio_set(struct gpio_chip *chip, unsigned offset, int value) +{ + struct lpc18xx_gpio_chip *gc = to_lpc18xx_gpio(chip); + writeb(value ? 1 : 0, gc->base + offset); +} + +static int lpc18xx_gpio_get(struct gpio_chip *chip, unsigned offset) +{ + struct lpc18xx_gpio_chip *gc = to_lpc18xx_gpio(chip); + return !!readb(gc->base + offset); +} + +static int lpc18xx_gpio_direction(struct gpio_chip *chip, unsigned offset, + bool out) +{ + struct lpc18xx_gpio_chip *gc = to_lpc18xx_gpio(chip); + unsigned long flags; + u32 port, pin, dir; + + port = offset / LPC18XX_PINS_PER_PORT; + pin = offset % LPC18XX_PINS_PER_PORT; + + spin_lock_irqsave(&gc->lock, flags); + dir = readl(gc->base + LPC18XX_REG_DIR(port)); + if (out) + dir |= BIT(pin); + else + dir &= ~BIT(pin); + writel(dir, gc->base + LPC18XX_REG_DIR(port)); + spin_unlock_irqrestore(&gc->lock, flags); + + return 0; +} + +static int lpc18xx_gpio_direction_input(struct gpio_chip *chip, + unsigned offset) +{ + return lpc18xx_gpio_direction(chip, offset, false); +} + +static int lpc18xx_gpio_direction_output(struct gpio_chip *chip, + unsigned offset, int value) +{ + lpc18xx_gpio_set(chip, offset, value); + return lpc18xx_gpio_direction(chip, offset, true); +} + +static struct gpio_chip lpc18xx_chip = { + .label = "lpc18xx/43xx-gpio", + .request = lpc18xx_gpio_request, + .free = lpc18xx_gpio_free, + .direction_input = lpc18xx_gpio_direction_input, + .direction_output = lpc18xx_gpio_direction_output, + .set = lpc18xx_gpio_set, + .get = lpc18xx_gpio_get, + .ngpio = LPC18XX_MAX_PORTS * LPC18XX_PINS_PER_PORT, + .owner = THIS_MODULE, +}; + +static int lpc18xx_gpio_probe(struct platform_device *pdev) +{ + struct lpc18xx_gpio_chip *gc; + struct resource *res; + int ret; + + gc = devm_kzalloc(&pdev->dev, sizeof(*gc), GFP_KERNEL); + if (!gc) + return -ENOMEM; + + gc->gpio = lpc18xx_chip; + platform_set_drvdata(pdev, gc); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + gc->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(gc->base)) + return PTR_ERR(gc->base); + + gc->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(gc->clk)) { + dev_err(&pdev->dev, "input clock not found\n"); + return PTR_ERR(gc->clk); + } + + ret = clk_prepare_enable(gc->clk); + if (ret) { + dev_err(&pdev->dev, "unable to enable clock\n"); + return ret; + } + + spin_lock_init(&gc->lock); + + gc->gpio.dev = &pdev->dev; + + ret = gpiochip_add(&gc->gpio); + if (ret) { + dev_err(&pdev->dev, "failed to add gpio chip\n"); + clk_disable_unprepare(gc->clk); + return ret; + } + + return 0; +} + +static int lpc18xx_gpio_remove(struct platform_device *pdev) +{ + struct lpc18xx_gpio_chip *gc = platform_get_drvdata(pdev); + + gpiochip_remove(&gc->gpio); + clk_disable_unprepare(gc->clk); + + return 0; +} + +static const struct of_device_id lpc18xx_gpio_match[] = { + { .compatible = "nxp,lpc1850-gpio" }, + { } +}; +MODULE_DEVICE_TABLE(of, lpc18xx_gpio_match); + +static struct platform_driver lpc18xx_gpio_driver = { + .probe = lpc18xx_gpio_probe, + .remove = lpc18xx_gpio_remove, + .driver = { + .name = "lpc18xx-gpio", + .of_match_table = lpc18xx_gpio_match, + }, +}; +module_platform_driver(lpc18xx_gpio_driver); + +MODULE_AUTHOR("Joachim Eastwood "); +MODULE_DESCRIPTION("GPIO driver for LPC18xx/43xx"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/gpio/gpio-lynxpoint.c b/drivers/gpio/gpio-lynxpoint.c index 127c755b38dc..153af464c7a7 100644 --- a/drivers/gpio/gpio-lynxpoint.c +++ b/drivers/gpio/gpio-lynxpoint.c @@ -72,7 +72,7 @@ struct lp_gpio { * * per gpio specific registers consist of two 32bit registers per gpio * (LP_CONFIG1 and LP_CONFIG2), with 94 gpios there's a total of - * 188 config registes. + * 188 config registers. * * A simplified view of the register layout look like this: * diff --git a/drivers/gpio/gpio-max732x.c b/drivers/gpio/gpio-max732x.c index 0fa4543c5e02..aed4ca9338bc 100644 --- a/drivers/gpio/gpio-max732x.c +++ b/drivers/gpio/gpio-max732x.c @@ -429,6 +429,14 @@ static int max732x_irq_set_type(struct irq_data *d, unsigned int type) return 0; } +static int max732x_irq_set_wake(struct irq_data *data, unsigned int on) +{ + struct max732x_chip *chip = irq_data_get_irq_chip_data(data); + + irq_set_irq_wake(chip->client->irq, on); + return 0; +} + static struct irq_chip max732x_irq_chip = { .name = "max732x", .irq_mask = max732x_irq_mask, @@ -436,6 +444,7 @@ static struct irq_chip max732x_irq_chip = { .irq_bus_lock = max732x_irq_bus_lock, .irq_bus_sync_unlock = max732x_irq_bus_sync_unlock, .irq_set_type = max732x_irq_set_type, + .irq_set_wake = max732x_irq_set_wake, }; static uint8_t max732x_irq_pending(struct max732x_chip *chip) @@ -507,12 +516,10 @@ static int max732x_irq_setup(struct max732x_chip *chip, chip->irq_features = has_irq; mutex_init(&chip->irq_lock); - ret = devm_request_threaded_irq(&client->dev, - client->irq, - NULL, - max732x_irq_handler, - IRQF_TRIGGER_FALLING | IRQF_ONESHOT, - dev_name(&client->dev), chip); + ret = devm_request_threaded_irq(&client->dev, client->irq, + NULL, max732x_irq_handler, IRQF_ONESHOT | + IRQF_TRIGGER_FALLING | IRQF_SHARED, + dev_name(&client->dev), chip); if (ret) { dev_err(&client->dev, "failed to request irq %d\n", client->irq); @@ -521,7 +528,7 @@ static int max732x_irq_setup(struct max732x_chip *chip, ret = gpiochip_irqchip_add(&chip->gpio_chip, &max732x_irq_chip, irq_base, - handle_edge_irq, + handle_simple_irq, IRQ_TYPE_NONE); if (ret) { dev_err(&client->dev, diff --git a/drivers/gpio/gpio-moxart.c b/drivers/gpio/gpio-moxart.c index c3ab46e595da..abd8676ce2b6 100644 --- a/drivers/gpio/gpio-moxart.c +++ b/drivers/gpio/gpio-moxart.c @@ -39,17 +39,6 @@ static void moxart_gpio_free(struct gpio_chip *chip, unsigned offset) pinctrl_free_gpio(offset); } -static int moxart_gpio_get(struct gpio_chip *chip, unsigned offset) -{ - struct bgpio_chip *bgc = to_bgpio_chip(chip); - u32 ret = bgc->read_reg(bgc->reg_dir); - - if (ret & BIT(offset)) - return !!(bgc->read_reg(bgc->reg_set) & BIT(offset)); - else - return !!(bgc->read_reg(bgc->reg_dat) & BIT(offset)); -} - static int moxart_gpio_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -68,8 +57,9 @@ static int moxart_gpio_probe(struct platform_device *pdev) return PTR_ERR(base); ret = bgpio_init(bgc, dev, 4, base + GPIO_DATA_IN, - base + GPIO_DATA_OUT, NULL, - base + GPIO_PIN_DIRECTION, NULL, 0); + base + GPIO_DATA_OUT, NULL, + base + GPIO_PIN_DIRECTION, NULL, + BGPIOF_READ_OUTPUT_REG_SET); if (ret) { dev_err(&pdev->dev, "bgpio_init failed\n"); return ret; @@ -78,7 +68,6 @@ static int moxart_gpio_probe(struct platform_device *pdev) bgc->gc.label = "moxart-gpio"; bgc->gc.request = moxart_gpio_request; bgc->gc.free = moxart_gpio_free; - bgc->gc.get = moxart_gpio_get; bgc->data = bgc->read_reg(bgc->reg_set); bgc->gc.base = 0; bgc->gc.ngpio = 32; diff --git a/drivers/gpio/gpio-mxc.c b/drivers/gpio/gpio-mxc.c index e4f42c95c320..ec1eb1b7250f 100644 --- a/drivers/gpio/gpio-mxc.c +++ b/drivers/gpio/gpio-mxc.c @@ -131,7 +131,7 @@ static struct mxc_gpio_hwdata *mxc_gpio_hwdata; #define GPIO_INT_FALL_EDGE (mxc_gpio_hwdata->fall_edge) #define GPIO_INT_BOTH_EDGES 0x4 -static struct platform_device_id mxc_gpio_devtype[] = { +static const struct platform_device_id mxc_gpio_devtype[] = { { .name = "imx1-gpio", .driver_data = IMX1_GPIO, @@ -449,7 +449,8 @@ static int mxc_gpio_probe(struct platform_device *pdev) err = bgpio_init(&port->bgc, &pdev->dev, 4, port->base + GPIO_PSR, port->base + GPIO_DR, NULL, - port->base + GPIO_GDIR, NULL, 0); + port->base + GPIO_GDIR, NULL, + BGPIOF_READ_OUTPUT_REG_SET); if (err) goto out_bgio; diff --git a/drivers/gpio/gpio-mxs.c b/drivers/gpio/gpio-mxs.c index eac872748ee7..551d15d7c369 100644 --- a/drivers/gpio/gpio-mxs.c +++ b/drivers/gpio/gpio-mxs.c @@ -239,7 +239,7 @@ static int mxs_gpio_get_direction(struct gpio_chip *gc, unsigned offset) return !(dir & mask); } -static struct platform_device_id mxs_gpio_ids[] = { +static const struct platform_device_id mxs_gpio_ids[] = { { .name = "imx23-gpio", .driver_data = IMX23_GPIO, diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c index b232397ad7ec..b0c57d505be7 100644 --- a/drivers/gpio/gpio-omap.c +++ b/drivers/gpio/gpio-omap.c @@ -488,9 +488,6 @@ static int omap_gpio_irq_type(struct irq_data *d, unsigned type) unsigned long flags; unsigned offset = d->hwirq; - if (!BANK_USED(bank)) - pm_runtime_get_sync(bank->dev); - if (type & ~IRQ_TYPE_SENSE_MASK) return -EINVAL; @@ -498,12 +495,18 @@ static int omap_gpio_irq_type(struct irq_data *d, unsigned type) (type & (IRQ_TYPE_LEVEL_LOW|IRQ_TYPE_LEVEL_HIGH))) return -EINVAL; + if (!BANK_USED(bank)) + pm_runtime_get_sync(bank->dev); + spin_lock_irqsave(&bank->lock, flags); retval = omap_set_gpio_triggering(bank, offset, type); + if (retval) + goto error; omap_gpio_init_irq(bank, offset); if (!omap_gpio_is_input(bank, offset)) { spin_unlock_irqrestore(&bank->lock, flags); - return -EINVAL; + retval = -EINVAL; + goto error; } spin_unlock_irqrestore(&bank->lock, flags); @@ -512,6 +515,11 @@ static int omap_gpio_irq_type(struct irq_data *d, unsigned type) else if (type & (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING)) __irq_set_handler_locked(d->irq, handle_edge_irq); + return 0; + +error: + if (!BANK_USED(bank)) + pm_runtime_put(bank->dev); return retval; } @@ -638,15 +646,6 @@ static int omap_set_gpio_wakeup(struct gpio_bank *bank, unsigned offset, return 0; } -static void omap_reset_gpio(struct gpio_bank *bank, unsigned offset) -{ - omap_set_gpio_direction(bank, offset, 1); - omap_set_gpio_irqenable(bank, offset, 0); - omap_clear_gpio_irqstatus(bank, offset); - omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE); - omap_clear_gpio_debounce(bank, offset); -} - /* Use disable_irq_wake() and enable_irq_wake() functions from drivers */ static int omap_gpio_wake_enable(struct irq_data *d, unsigned int enable) { @@ -669,14 +668,7 @@ static int omap_gpio_request(struct gpio_chip *chip, unsigned offset) pm_runtime_get_sync(bank->dev); spin_lock_irqsave(&bank->lock, flags); - /* Set trigger to none. You need to enable the desired trigger with - * request_irq() or set_irq_type(). Only do this if the IRQ line has - * not already been requested. - */ - if (!LINE_USED(bank->irq_usage, offset)) { - omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE); - omap_enable_gpio_module(bank, offset); - } + omap_enable_gpio_module(bank, offset); bank->mod_usage |= BIT(offset); spin_unlock_irqrestore(&bank->lock, flags); @@ -690,8 +682,11 @@ static void omap_gpio_free(struct gpio_chip *chip, unsigned offset) spin_lock_irqsave(&bank->lock, flags); bank->mod_usage &= ~(BIT(offset)); + if (!LINE_USED(bank->irq_usage, offset)) { + omap_set_gpio_direction(bank, offset, 1); + omap_clear_gpio_debounce(bank, offset); + } omap_disable_gpio_module(bank, offset); - omap_reset_gpio(bank, offset); spin_unlock_irqrestore(&bank->lock, flags); /* @@ -795,11 +790,23 @@ static unsigned int omap_gpio_irq_startup(struct irq_data *d) pm_runtime_get_sync(bank->dev); spin_lock_irqsave(&bank->lock, flags); - omap_gpio_init_irq(bank, offset); + + if (!LINE_USED(bank->mod_usage, offset)) + omap_set_gpio_direction(bank, offset, 1); + else if (!omap_gpio_is_input(bank, offset)) + goto err; + omap_enable_gpio_module(bank, offset); + bank->irq_usage |= BIT(offset); + spin_unlock_irqrestore(&bank->lock, flags); omap_gpio_unmask_irq(d); return 0; +err: + spin_unlock_irqrestore(&bank->lock, flags); + if (!BANK_USED(bank)) + pm_runtime_put(bank->dev); + return -EINVAL; } static void omap_gpio_irq_shutdown(struct irq_data *d) @@ -810,8 +817,12 @@ static void omap_gpio_irq_shutdown(struct irq_data *d) spin_lock_irqsave(&bank->lock, flags); bank->irq_usage &= ~(BIT(offset)); + omap_set_gpio_irqenable(bank, offset, 0); + omap_clear_gpio_irqstatus(bank, offset); + omap_set_gpio_triggering(bank, offset, IRQ_TYPE_NONE); + if (!LINE_USED(bank->mod_usage, offset)) + omap_clear_gpio_debounce(bank, offset); omap_disable_gpio_module(bank, offset); - omap_reset_gpio(bank, offset); spin_unlock_irqrestore(&bank->lock, flags); /* @@ -1233,6 +1244,17 @@ static int omap_gpio_probe(struct platform_device *pdev) return 0; } +static int omap_gpio_remove(struct platform_device *pdev) +{ + struct gpio_bank *bank = platform_get_drvdata(pdev); + + list_del(&bank->node); + gpiochip_remove(&bank->chip); + pm_runtime_disable(bank->dev); + + return 0; +} + #ifdef CONFIG_ARCH_OMAP2PLUS #if defined(CONFIG_PM) @@ -1418,6 +1440,7 @@ static int omap_gpio_runtime_resume(struct device *dev) } #endif /* CONFIG_PM */ +#if IS_BUILTIN(CONFIG_GPIO_OMAP) void omap2_gpio_prepare_for_idle(int pwr_mode) { struct gpio_bank *bank; @@ -1443,6 +1466,7 @@ void omap2_gpio_resume_after_idle(void) pm_runtime_get_sync(bank->dev); } } +#endif #if defined(CONFIG_PM) static void omap_gpio_init_context(struct gpio_bank *p) @@ -1598,6 +1622,7 @@ MODULE_DEVICE_TABLE(of, omap_gpio_match); static struct platform_driver omap_gpio_driver = { .probe = omap_gpio_probe, + .remove = omap_gpio_remove, .driver = { .name = "omap_gpio", .pm = &gpio_pm_ops, @@ -1615,3 +1640,13 @@ static int __init omap_gpio_drv_reg(void) return platform_driver_register(&omap_gpio_driver); } postcore_initcall(omap_gpio_drv_reg); + +static void __exit omap_gpio_exit(void) +{ + platform_driver_unregister(&omap_gpio_driver); +} +module_exit(omap_gpio_exit); + +MODULE_DESCRIPTION("omap gpio driver"); +MODULE_ALIAS("platform:gpio-omap"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/gpio/gpio-pca953x.c b/drivers/gpio/gpio-pca953x.c index e2da64abbccd..d233eb3b8132 100644 --- a/drivers/gpio/gpio-pca953x.c +++ b/drivers/gpio/gpio-pca953x.c @@ -443,12 +443,13 @@ static struct irq_chip pca953x_irq_chip = { .irq_set_type = pca953x_irq_set_type, }; -static u8 pca953x_irq_pending(struct pca953x_chip *chip, u8 *pending) +static bool pca953x_irq_pending(struct pca953x_chip *chip, u8 *pending) { u8 cur_stat[MAX_BANK]; u8 old_stat[MAX_BANK]; - u8 pendings = 0; - u8 trigger[MAX_BANK], triggers = 0; + bool pending_seen = false; + bool trigger_seen = false; + u8 trigger[MAX_BANK]; int ret, i, offset = 0; switch (chip->chip_type) { @@ -461,7 +462,7 @@ static u8 pca953x_irq_pending(struct pca953x_chip *chip, u8 *pending) } ret = pca953x_read_regs(chip, offset, cur_stat); if (ret) - return 0; + return false; /* Remove output pins from the equation */ for (i = 0; i < NBANK(chip); i++) @@ -471,11 +472,12 @@ static u8 pca953x_irq_pending(struct pca953x_chip *chip, u8 *pending) for (i = 0; i < NBANK(chip); i++) { trigger[i] = (cur_stat[i] ^ old_stat[i]) & chip->irq_mask[i]; - triggers += trigger[i]; + if (trigger[i]) + trigger_seen = true; } - if (!triggers) - return 0; + if (!trigger_seen) + return false; memcpy(chip->irq_stat, cur_stat, NBANK(chip)); @@ -483,10 +485,11 @@ static u8 pca953x_irq_pending(struct pca953x_chip *chip, u8 *pending) pending[i] = (old_stat[i] & chip->irq_trig_fall[i]) | (cur_stat[i] & chip->irq_trig_raise[i]); pending[i] &= trigger[i]; - pendings += pending[i]; + if (pending[i]) + pending_seen = true; } - return pendings; + return pending_seen; } static irqreturn_t pca953x_irq_handler(int irq, void *devid) @@ -630,7 +633,7 @@ static int device_pca957x_init(struct pca953x_chip *chip, u32 invert) memset(val, 0, NBANK(chip)); pca953x_write_regs(chip, PCA957X_INVRT, val); - /* To enable register 6, 7 to controll pull up and pull down */ + /* To enable register 6, 7 to control pull up and pull down */ memset(val, 0x02, NBANK(chip)); pca953x_write_regs(chip, PCA957X_BKEN, val); diff --git a/drivers/gpio/gpio-pcf857x.c b/drivers/gpio/gpio-pcf857x.c index 945f0cda8529..404f3c61ef9b 100644 --- a/drivers/gpio/gpio-pcf857x.c +++ b/drivers/gpio/gpio-pcf857x.c @@ -91,6 +91,8 @@ struct pcf857x { spinlock_t slock; /* protect irq demux */ unsigned out; /* software latch */ unsigned status; /* current status */ + unsigned int irq_parent; + unsigned irq_enabled; /* enabled irqs */ int (*write)(struct i2c_client *client, unsigned data); int (*read)(struct i2c_client *client); @@ -194,7 +196,7 @@ static irqreturn_t pcf857x_irq(int irq, void *data) * interrupt source, just to avoid bad irqs */ - change = (gpio->status ^ status); + change = (gpio->status ^ status) & gpio->irq_enabled; for_each_set_bit(i, &change, gpio->chip.ngpio) handle_nested_irq(irq_find_mapping(gpio->chip.irqdomain, i)); gpio->status = status; @@ -209,29 +211,62 @@ static irqreturn_t pcf857x_irq(int irq, void *data) */ static void noop(struct irq_data *data) { } -static unsigned int noop_ret(struct irq_data *data) -{ - return 0; -} - static int pcf857x_irq_set_wake(struct irq_data *data, unsigned int on) { struct pcf857x *gpio = irq_data_get_irq_chip_data(data); - irq_set_irq_wake(gpio->client->irq, on); - return 0; + int error = 0; + + if (gpio->irq_parent) { + error = irq_set_irq_wake(gpio->irq_parent, on); + if (error) { + dev_dbg(&gpio->client->dev, + "irq %u doesn't support irq_set_wake\n", + gpio->irq_parent); + gpio->irq_parent = 0; + } + } + return error; +} + +static void pcf857x_irq_enable(struct irq_data *data) +{ + struct pcf857x *gpio = irq_data_get_irq_chip_data(data); + + gpio->irq_enabled |= (1 << data->hwirq); +} + +static void pcf857x_irq_disable(struct irq_data *data) +{ + struct pcf857x *gpio = irq_data_get_irq_chip_data(data); + + gpio->irq_enabled &= ~(1 << data->hwirq); +} + +static void pcf857x_irq_bus_lock(struct irq_data *data) +{ + struct pcf857x *gpio = irq_data_get_irq_chip_data(data); + + mutex_lock(&gpio->lock); +} + +static void pcf857x_irq_bus_sync_unlock(struct irq_data *data) +{ + struct pcf857x *gpio = irq_data_get_irq_chip_data(data); + + mutex_unlock(&gpio->lock); } static struct irq_chip pcf857x_irq_chip = { .name = "pcf857x", - .irq_startup = noop_ret, - .irq_shutdown = noop, - .irq_enable = noop, - .irq_disable = noop, + .irq_enable = pcf857x_irq_enable, + .irq_disable = pcf857x_irq_disable, .irq_ack = noop, .irq_mask = noop, .irq_unmask = noop, .irq_set_wake = pcf857x_irq_set_wake, + .irq_bus_lock = pcf857x_irq_bus_lock, + .irq_bus_sync_unlock = pcf857x_irq_bus_sync_unlock, }; /*-------------------------------------------------------------------------*/ @@ -364,6 +399,7 @@ static int pcf857x_probe(struct i2c_client *client, gpiochip_set_chained_irqchip(&gpio->chip, &pcf857x_irq_chip, client->irq, NULL); + gpio->irq_parent = client->irq; } /* Let platform code set up the GPIOs and their users. diff --git a/drivers/gpio/gpio-rcar.c b/drivers/gpio/gpio-rcar.c index fd3977465948..1e14a6c74ed1 100644 --- a/drivers/gpio/gpio-rcar.c +++ b/drivers/gpio/gpio-rcar.c @@ -177,8 +177,17 @@ static int gpio_rcar_irq_set_wake(struct irq_data *d, unsigned int on) struct gpio_chip *gc = irq_data_get_irq_chip_data(d); struct gpio_rcar_priv *p = container_of(gc, struct gpio_rcar_priv, gpio_chip); + int error; - irq_set_irq_wake(p->irq_parent, on); + if (p->irq_parent) { + error = irq_set_irq_wake(p->irq_parent, on); + if (error) { + dev_dbg(&p->pdev->dev, + "irq %u doesn't support irq_set_wake\n", + p->irq_parent); + p->irq_parent = 0; + } + } if (!p->clk) return 0; diff --git a/drivers/gpio/gpio-stp-xway.c b/drivers/gpio/gpio-stp-xway.c index 202361eb7279..81bdbe7ba2a4 100644 --- a/drivers/gpio/gpio-stp-xway.c +++ b/drivers/gpio/gpio-stp-xway.c @@ -58,7 +58,7 @@ #define XWAY_STP_ADSL_MASK 0x3 /* 2 groups of 3 bits can be driven by the phys */ -#define XWAY_STP_PHY_MASK 0x3 +#define XWAY_STP_PHY_MASK 0x7 #define XWAY_STP_PHY1_SHIFT 27 #define XWAY_STP_PHY2_SHIFT 15 @@ -200,7 +200,7 @@ static int xway_stp_hw_init(struct xway_stp *chip) static int xway_stp_probe(struct platform_device *pdev) { struct resource *res; - const __be32 *shadow, *groups, *dsl, *phy; + u32 shadow, groups, dsl, phy; struct xway_stp *chip; struct clk *clk; int ret = 0; @@ -223,33 +223,28 @@ static int xway_stp_probe(struct platform_device *pdev) chip->gc.owner = THIS_MODULE; /* store the shadow value if one was passed by the devicetree */ - shadow = of_get_property(pdev->dev.of_node, "lantiq,shadow", NULL); - if (shadow) - chip->shadow = be32_to_cpu(*shadow); + if (!of_property_read_u32(pdev->dev.of_node, "lantiq,shadow", &shadow)) + chip->shadow = shadow; /* find out which gpio groups should be enabled */ - groups = of_get_property(pdev->dev.of_node, "lantiq,groups", NULL); - if (groups) - chip->groups = be32_to_cpu(*groups) & XWAY_STP_GROUP_MASK; + if (!of_property_read_u32(pdev->dev.of_node, "lantiq,groups", &groups)) + chip->groups = groups & XWAY_STP_GROUP_MASK; else chip->groups = XWAY_STP_GROUP0; chip->gc.ngpio = fls(chip->groups) * 8; /* find out which gpios are controlled by the dsl core */ - dsl = of_get_property(pdev->dev.of_node, "lantiq,dsl", NULL); - if (dsl) - chip->dsl = be32_to_cpu(*dsl) & XWAY_STP_ADSL_MASK; + if (!of_property_read_u32(pdev->dev.of_node, "lantiq,dsl", &dsl)) + chip->dsl = dsl & XWAY_STP_ADSL_MASK; /* find out which gpios are controlled by the phys */ if (of_machine_is_compatible("lantiq,ar9") || of_machine_is_compatible("lantiq,gr9") || of_machine_is_compatible("lantiq,vr9")) { - phy = of_get_property(pdev->dev.of_node, "lantiq,phy1", NULL); - if (phy) - chip->phy1 = be32_to_cpu(*phy) & XWAY_STP_PHY_MASK; - phy = of_get_property(pdev->dev.of_node, "lantiq,phy2", NULL); - if (phy) - chip->phy2 = be32_to_cpu(*phy) & XWAY_STP_PHY_MASK; + if (!of_property_read_u32(pdev->dev.of_node, "lantiq,phy1", &phy)) + chip->phy1 = phy & XWAY_STP_PHY_MASK; + if (!of_property_read_u32(pdev->dev.of_node, "lantiq,phy2", &phy)) + chip->phy2 = phy & XWAY_STP_PHY_MASK; } /* check which edge trigger we should use, default to a falling edge */ diff --git a/drivers/gpio/gpio-tb10x.c b/drivers/gpio/gpio-tb10x.c index 46b89614aa91..12c99d969b98 100644 --- a/drivers/gpio/gpio-tb10x.c +++ b/drivers/gpio/gpio-tb10x.c @@ -292,7 +292,6 @@ static int tb10x_gpio_remove(struct platform_device *pdev) BIT(tb10x_gpio->gc.ngpio) - 1, 0, 0); kfree(tb10x_gpio->domain->gc); irq_domain_remove(tb10x_gpio->domain); - free_irq(tb10x_gpio->irq, tb10x_gpio); } gpiochip_remove(&tb10x_gpio->gc); diff --git a/drivers/gpio/gpio-tegra.c b/drivers/gpio/gpio-tegra.c index 56dcc8ed98de..9b25c90f725c 100644 --- a/drivers/gpio/gpio-tegra.c +++ b/drivers/gpio/gpio-tegra.c @@ -288,7 +288,7 @@ static void tegra_gpio_irq_handler(unsigned int irq, struct irq_desc *desc) tegra_gpio_writel(1 << pin, GPIO_INT_CLR(gpio)); /* if gpio is edge triggered, clear condition - * before executing the hander so that we don't + * before executing the handler so that we don't * miss edges */ if (lvl & (0x100 << pin)) { diff --git a/drivers/gpio/gpio-ts5500.c b/drivers/gpio/gpio-ts5500.c index 92fbabd82879..b29a102d136b 100644 --- a/drivers/gpio/gpio-ts5500.c +++ b/drivers/gpio/gpio-ts5500.c @@ -440,7 +440,7 @@ static int ts5500_dio_remove(struct platform_device *pdev) return 0; } -static struct platform_device_id ts5500_dio_ids[] = { +static const struct platform_device_id ts5500_dio_ids[] = { { "ts5500-dio1", TS5500_DIO1 }, { "ts5500-dio2", TS5500_DIO2 }, { "ts5500-dio-lcd", TS5500_LCD }, diff --git a/drivers/gpio/gpio-xgene-sb.c b/drivers/gpio/gpio-xgene-sb.c index fb9d29a5d584..d57068b9083e 100644 --- a/drivers/gpio/gpio-xgene-sb.c +++ b/drivers/gpio/gpio-xgene-sb.c @@ -25,8 +25,11 @@ #include #include #include +#include #include +#include "gpiolib.h" + #define XGENE_MAX_GPIO_DS 22 #define XGENE_MAX_GPIO_DS_IRQ 6 @@ -112,7 +115,6 @@ static int xgene_gpio_sb_probe(struct platform_device *pdev) GFP_KERNEL); if (!priv->irq) return -ENOMEM; - memset(priv->irq, 0, sizeof(u32) * XGENE_MAX_GPIO_DS); for (i = 0; i < priv->nirq; i++) { priv->irq[default_lines[i]] = platform_get_irq(pdev, i); @@ -129,6 +131,11 @@ static int xgene_gpio_sb_probe(struct platform_device *pdev) else dev_info(&pdev->dev, "X-Gene GPIO Standby driver registered\n"); + if (priv->nirq > 0) { + /* Register interrupt handlers for gpio signaled acpi events */ + acpi_gpiochip_request_interrupts(&priv->bgc.gc); + } + return ret; } @@ -136,6 +143,10 @@ static int xgene_gpio_sb_remove(struct platform_device *pdev) { struct xgene_gpio_sb *priv = platform_get_drvdata(pdev); + if (priv->nirq > 0) { + acpi_gpiochip_free_interrupts(&priv->bgc.gc); + } + return bgpio_remove(&priv->bgc); } @@ -145,10 +156,19 @@ static const struct of_device_id xgene_gpio_sb_of_match[] = { }; MODULE_DEVICE_TABLE(of, xgene_gpio_sb_of_match); +#ifdef CONFIG_ACPI +static const struct acpi_device_id xgene_gpio_sb_acpi_match[] = { + {"APMC0D15", 0}, + {}, +}; +MODULE_DEVICE_TABLE(acpi, xgene_gpio_sb_acpi_match); +#endif + static struct platform_driver xgene_gpio_sb_driver = { .driver = { .name = "xgene-gpio-sb", .of_match_table = xgene_gpio_sb_of_match, + .acpi_match_table = ACPI_PTR(xgene_gpio_sb_acpi_match), }, .probe = xgene_gpio_sb_probe, .remove = xgene_gpio_sb_remove, diff --git a/drivers/gpio/gpio-xilinx.c b/drivers/gpio/gpio-xilinx.c index 61243d177740..77fe5d3cb105 100644 --- a/drivers/gpio/gpio-xilinx.c +++ b/drivers/gpio/gpio-xilinx.c @@ -41,10 +41,10 @@ /** * struct xgpio_instance - Stores information about GPIO device * @mmchip: OF GPIO chip for memory mapped banks + * @gpio_width: GPIO width for every channel * @gpio_state: GPIO state shadow register * @gpio_dir: GPIO direction shadow register * @gpio_lock: Lock used for synchronization - * @inited: True if the port has been inited */ struct xgpio_instance { struct of_mm_gpio_chip mmchip; @@ -231,6 +231,8 @@ static void xgpio_save_regs(struct of_mm_gpio_chip *mm_gc) * @pdev: pointer to the platform device * * This function remove gpiochips and frees all the allocated resources. + * + * Return: 0 always */ static int xgpio_remove(struct platform_device *pdev) { diff --git a/drivers/gpio/gpio-xlp.c b/drivers/gpio/gpio-xlp.c new file mode 100644 index 000000000000..9bdab7203d65 --- /dev/null +++ b/drivers/gpio/gpio-xlp.c @@ -0,0 +1,427 @@ +/* + * Copyright (C) 2003-2015 Broadcom Corporation + * All Rights Reserved + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include + +/* + * XLP GPIO has multiple 32 bit registers for each feature where each register + * controls 32 pins. So, pins up to 64 require 2 32-bit registers and up to 96 + * require 3 32-bit registers for each feature. + * Here we only define offset of the first register for each feature. Offset of + * the registers for pins greater than 32 can be calculated as following(Use + * GPIO_INT_STAT as example): + * + * offset = (gpio / XLP_GPIO_REGSZ) * 4; + * reg_addr = addr + offset; + * + * where addr is base address of the that feature register and gpio is the pin. + */ +#define GPIO_OUTPUT_EN 0x00 +#define GPIO_PADDRV 0x08 +#define GPIO_INT_EN00 0x18 +#define GPIO_INT_EN10 0x20 +#define GPIO_INT_EN20 0x28 +#define GPIO_INT_EN30 0x30 +#define GPIO_INT_POL 0x38 +#define GPIO_INT_TYPE 0x40 +#define GPIO_INT_STAT 0x48 + +#define GPIO_9XX_BYTESWAP 0X00 +#define GPIO_9XX_CTRL 0X04 +#define GPIO_9XX_OUTPUT_EN 0x14 +#define GPIO_9XX_PADDRV 0x24 +/* + * Only for 4 interrupt enable reg are defined for now, + * total reg available are 12. + */ +#define GPIO_9XX_INT_EN00 0x44 +#define GPIO_9XX_INT_EN10 0x54 +#define GPIO_9XX_INT_EN20 0x64 +#define GPIO_9XX_INT_EN30 0x74 +#define GPIO_9XX_INT_POL 0x104 +#define GPIO_9XX_INT_TYPE 0x114 +#define GPIO_9XX_INT_STAT 0x124 + +#define GPIO_3XX_INT_EN00 0x18 +#define GPIO_3XX_INT_EN10 0x20 +#define GPIO_3XX_INT_EN20 0x28 +#define GPIO_3XX_INT_EN30 0x30 +#define GPIO_3XX_INT_POL 0x78 +#define GPIO_3XX_INT_TYPE 0x80 +#define GPIO_3XX_INT_STAT 0x88 + +/* Interrupt type register mask */ +#define XLP_GPIO_IRQ_TYPE_LVL 0x0 +#define XLP_GPIO_IRQ_TYPE_EDGE 0x1 + +/* Interrupt polarity register mask */ +#define XLP_GPIO_IRQ_POL_HIGH 0x0 +#define XLP_GPIO_IRQ_POL_LOW 0x1 + +#define XLP_GPIO_REGSZ 32 +#define XLP_GPIO_IRQ_BASE 768 +#define XLP_MAX_NR_GPIO 96 + +/* XLP variants supported by this driver */ +enum { + XLP_GPIO_VARIANT_XLP832 = 1, + XLP_GPIO_VARIANT_XLP316, + XLP_GPIO_VARIANT_XLP208, + XLP_GPIO_VARIANT_XLP980, + XLP_GPIO_VARIANT_XLP532 +}; + +struct xlp_gpio_priv { + struct gpio_chip chip; + DECLARE_BITMAP(gpio_enabled_mask, XLP_MAX_NR_GPIO); + void __iomem *gpio_intr_en; /* pointer to first intr enable reg */ + void __iomem *gpio_intr_stat; /* pointer to first intr status reg */ + void __iomem *gpio_intr_type; /* pointer to first intr type reg */ + void __iomem *gpio_intr_pol; /* pointer to first intr polarity reg */ + void __iomem *gpio_out_en; /* pointer to first output enable reg */ + void __iomem *gpio_paddrv; /* pointer to first pad drive reg */ + spinlock_t lock; +}; + +static struct xlp_gpio_priv *gpio_chip_to_xlp_priv(struct gpio_chip *gc) +{ + return container_of(gc, struct xlp_gpio_priv, chip); +} + +static int xlp_gpio_get_reg(void __iomem *addr, unsigned gpio) +{ + u32 pos, regset; + + pos = gpio % XLP_GPIO_REGSZ; + regset = (gpio / XLP_GPIO_REGSZ) * 4; + return !!(readl(addr + regset) & BIT(pos)); +} + +static void xlp_gpio_set_reg(void __iomem *addr, unsigned gpio, int state) +{ + u32 value, pos, regset; + + pos = gpio % XLP_GPIO_REGSZ; + regset = (gpio / XLP_GPIO_REGSZ) * 4; + value = readl(addr + regset); + + if (state) + value |= BIT(pos); + else + value &= ~BIT(pos); + + writel(value, addr + regset); +} + +static void xlp_gpio_irq_disable(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct xlp_gpio_priv *priv = gpio_chip_to_xlp_priv(gc); + unsigned long flags; + + spin_lock_irqsave(&priv->lock, flags); + xlp_gpio_set_reg(priv->gpio_intr_en, d->hwirq, 0x0); + __clear_bit(d->hwirq, priv->gpio_enabled_mask); + spin_unlock_irqrestore(&priv->lock, flags); +} + +static void xlp_gpio_irq_mask_ack(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct xlp_gpio_priv *priv = gpio_chip_to_xlp_priv(gc); + unsigned long flags; + + spin_lock_irqsave(&priv->lock, flags); + xlp_gpio_set_reg(priv->gpio_intr_en, d->hwirq, 0x0); + xlp_gpio_set_reg(priv->gpio_intr_stat, d->hwirq, 0x1); + __clear_bit(d->hwirq, priv->gpio_enabled_mask); + spin_unlock_irqrestore(&priv->lock, flags); +} + +static void xlp_gpio_irq_unmask(struct irq_data *d) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct xlp_gpio_priv *priv = gpio_chip_to_xlp_priv(gc); + unsigned long flags; + + spin_lock_irqsave(&priv->lock, flags); + xlp_gpio_set_reg(priv->gpio_intr_en, d->hwirq, 0x1); + __set_bit(d->hwirq, priv->gpio_enabled_mask); + spin_unlock_irqrestore(&priv->lock, flags); +} + +static int xlp_gpio_set_irq_type(struct irq_data *d, unsigned int type) +{ + struct gpio_chip *gc = irq_data_get_irq_chip_data(d); + struct xlp_gpio_priv *priv = gpio_chip_to_xlp_priv(gc); + int pol, irq_type; + + switch (type) { + case IRQ_TYPE_EDGE_RISING: + irq_type = XLP_GPIO_IRQ_TYPE_EDGE; + pol = XLP_GPIO_IRQ_POL_HIGH; + break; + case IRQ_TYPE_EDGE_FALLING: + irq_type = XLP_GPIO_IRQ_TYPE_EDGE; + pol = XLP_GPIO_IRQ_POL_LOW; + break; + case IRQ_TYPE_LEVEL_HIGH: + irq_type = XLP_GPIO_IRQ_TYPE_LVL; + pol = XLP_GPIO_IRQ_POL_HIGH; + break; + case IRQ_TYPE_LEVEL_LOW: + irq_type = XLP_GPIO_IRQ_TYPE_LVL; + pol = XLP_GPIO_IRQ_POL_LOW; + break; + default: + return -EINVAL; + } + + xlp_gpio_set_reg(priv->gpio_intr_type, d->hwirq, irq_type); + xlp_gpio_set_reg(priv->gpio_intr_pol, d->hwirq, pol); + + return 0; +} + +static struct irq_chip xlp_gpio_irq_chip = { + .name = "XLP-GPIO", + .irq_mask_ack = xlp_gpio_irq_mask_ack, + .irq_disable = xlp_gpio_irq_disable, + .irq_set_type = xlp_gpio_set_irq_type, + .irq_unmask = xlp_gpio_irq_unmask, + .flags = IRQCHIP_ONESHOT_SAFE, +}; + +static irqreturn_t xlp_gpio_generic_handler(int irq, void *data) +{ + struct xlp_gpio_priv *priv = data; + int gpio, regoff; + u32 gpio_stat; + + regoff = -1; + gpio_stat = 0; + for_each_set_bit(gpio, priv->gpio_enabled_mask, XLP_MAX_NR_GPIO) { + if (regoff != gpio / XLP_GPIO_REGSZ) { + regoff = gpio / XLP_GPIO_REGSZ; + gpio_stat = readl(priv->gpio_intr_stat + regoff * 4); + } + if (gpio_stat & BIT(gpio % XLP_GPIO_REGSZ)) + generic_handle_irq(irq_find_mapping( + priv->chip.irqdomain, gpio)); + } + + return IRQ_HANDLED; +} + +static int xlp_gpio_dir_output(struct gpio_chip *gc, unsigned gpio, int state) +{ + struct xlp_gpio_priv *priv = gpio_chip_to_xlp_priv(gc); + + BUG_ON(gpio >= gc->ngpio); + xlp_gpio_set_reg(priv->gpio_out_en, gpio, 0x1); + + return 0; +} + +static int xlp_gpio_dir_input(struct gpio_chip *gc, unsigned gpio) +{ + struct xlp_gpio_priv *priv = gpio_chip_to_xlp_priv(gc); + + BUG_ON(gpio >= gc->ngpio); + xlp_gpio_set_reg(priv->gpio_out_en, gpio, 0x0); + + return 0; +} + +static int xlp_gpio_get(struct gpio_chip *gc, unsigned gpio) +{ + struct xlp_gpio_priv *priv = gpio_chip_to_xlp_priv(gc); + + BUG_ON(gpio >= gc->ngpio); + return xlp_gpio_get_reg(priv->gpio_paddrv, gpio); +} + +static void xlp_gpio_set(struct gpio_chip *gc, unsigned gpio, int state) +{ + struct xlp_gpio_priv *priv = gpio_chip_to_xlp_priv(gc); + + BUG_ON(gpio >= gc->ngpio); + xlp_gpio_set_reg(priv->gpio_paddrv, gpio, state); +} + +static const struct of_device_id xlp_gpio_of_ids[] = { + { + .compatible = "netlogic,xlp832-gpio", + .data = (void *)XLP_GPIO_VARIANT_XLP832, + }, + { + .compatible = "netlogic,xlp316-gpio", + .data = (void *)XLP_GPIO_VARIANT_XLP316, + }, + { + .compatible = "netlogic,xlp208-gpio", + .data = (void *)XLP_GPIO_VARIANT_XLP208, + }, + { + .compatible = "netlogic,xlp980-gpio", + .data = (void *)XLP_GPIO_VARIANT_XLP980, + }, + { + .compatible = "netlogic,xlp532-gpio", + .data = (void *)XLP_GPIO_VARIANT_XLP532, + }, + { /* sentinel */ }, +}; +MODULE_DEVICE_TABLE(of, xlp_gpio_of_ids); + +static int xlp_gpio_probe(struct platform_device *pdev) +{ + struct gpio_chip *gc; + struct resource *iores; + struct xlp_gpio_priv *priv; + const struct of_device_id *of_id; + void __iomem *gpio_base; + int irq_base, irq, err; + int ngpio; + u32 soc_type; + + iores = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!iores) + return -ENODEV; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + gpio_base = devm_ioremap_resource(&pdev->dev, iores); + if (IS_ERR(gpio_base)) + return PTR_ERR(gpio_base); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + of_id = of_match_device(xlp_gpio_of_ids, &pdev->dev); + if (!of_id) { + dev_err(&pdev->dev, "Failed to get soc type!\n"); + return -ENODEV; + } + + soc_type = (uintptr_t) of_id->data; + + switch (soc_type) { + case XLP_GPIO_VARIANT_XLP832: + priv->gpio_out_en = gpio_base + GPIO_OUTPUT_EN; + priv->gpio_paddrv = gpio_base + GPIO_PADDRV; + priv->gpio_intr_stat = gpio_base + GPIO_INT_STAT; + priv->gpio_intr_type = gpio_base + GPIO_INT_TYPE; + priv->gpio_intr_pol = gpio_base + GPIO_INT_POL; + priv->gpio_intr_en = gpio_base + GPIO_INT_EN00; + ngpio = 41; + break; + case XLP_GPIO_VARIANT_XLP208: + case XLP_GPIO_VARIANT_XLP316: + priv->gpio_out_en = gpio_base + GPIO_OUTPUT_EN; + priv->gpio_paddrv = gpio_base + GPIO_PADDRV; + priv->gpio_intr_stat = gpio_base + GPIO_3XX_INT_STAT; + priv->gpio_intr_type = gpio_base + GPIO_3XX_INT_TYPE; + priv->gpio_intr_pol = gpio_base + GPIO_3XX_INT_POL; + priv->gpio_intr_en = gpio_base + GPIO_3XX_INT_EN00; + + ngpio = (soc_type == XLP_GPIO_VARIANT_XLP208) ? 42 : 57; + break; + case XLP_GPIO_VARIANT_XLP980: + case XLP_GPIO_VARIANT_XLP532: + priv->gpio_out_en = gpio_base + GPIO_9XX_OUTPUT_EN; + priv->gpio_paddrv = gpio_base + GPIO_9XX_PADDRV; + priv->gpio_intr_stat = gpio_base + GPIO_9XX_INT_STAT; + priv->gpio_intr_type = gpio_base + GPIO_9XX_INT_TYPE; + priv->gpio_intr_pol = gpio_base + GPIO_9XX_INT_POL; + priv->gpio_intr_en = gpio_base + GPIO_9XX_INT_EN00; + + ngpio = (soc_type == XLP_GPIO_VARIANT_XLP980) ? 66 : 67; + break; + default: + dev_err(&pdev->dev, "Unknown Processor type!\n"); + return -ENODEV; + } + + bitmap_zero(priv->gpio_enabled_mask, XLP_MAX_NR_GPIO); + + gc = &priv->chip; + + gc->owner = THIS_MODULE; + gc->label = dev_name(&pdev->dev); + gc->base = 0; + gc->dev = &pdev->dev; + gc->ngpio = ngpio; + gc->of_node = pdev->dev.of_node; + gc->direction_output = xlp_gpio_dir_output; + gc->direction_input = xlp_gpio_dir_input; + gc->set = xlp_gpio_set; + gc->get = xlp_gpio_get; + + spin_lock_init(&priv->lock); + + err = devm_request_irq(&pdev->dev, irq, xlp_gpio_generic_handler, + IRQ_TYPE_NONE, pdev->name, priv); + if (err) + return err; + + irq_base = irq_alloc_descs(-1, XLP_GPIO_IRQ_BASE, gc->ngpio, 0); + if (irq_base < 0) { + dev_err(&pdev->dev, "Failed to allocate IRQ numbers\n"); + return err; + } + + err = gpiochip_add(gc); + if (err < 0) + goto out_free_desc; + + err = gpiochip_irqchip_add(gc, &xlp_gpio_irq_chip, irq_base, + handle_level_irq, IRQ_TYPE_NONE); + if (err) { + dev_err(&pdev->dev, "Could not connect irqchip to gpiochip!\n"); + goto out_gpio_remove; + } + + dev_info(&pdev->dev, "registered %d GPIOs\n", gc->ngpio); + + return 0; + +out_gpio_remove: + gpiochip_remove(gc); +out_free_desc: + irq_free_descs(irq_base, gc->ngpio); + return err; +} + +static struct platform_driver xlp_gpio_driver = { + .driver = { + .name = "xlp-gpio", + .of_match_table = xlp_gpio_of_ids, + }, + .probe = xlp_gpio_probe, +}; +module_platform_driver(xlp_gpio_driver); + +MODULE_AUTHOR("Kamlakant Patel "); +MODULE_AUTHOR("Ganesan Ramalingam "); +MODULE_DESCRIPTION("Netlogic XLP GPIO Driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/gpio/gpio-zynq.c b/drivers/gpio/gpio-zynq.c index 184c4b1b2558..2e87c4b8da26 100644 --- a/drivers/gpio/gpio-zynq.c +++ b/drivers/gpio/gpio-zynq.c @@ -18,34 +18,47 @@ #include #include #include +#include #define DRIVER_NAME "zynq-gpio" /* Maximum banks */ #define ZYNQ_GPIO_MAX_BANK 4 +#define ZYNQMP_GPIO_MAX_BANK 6 #define ZYNQ_GPIO_BANK0_NGPIO 32 #define ZYNQ_GPIO_BANK1_NGPIO 22 #define ZYNQ_GPIO_BANK2_NGPIO 32 #define ZYNQ_GPIO_BANK3_NGPIO 32 -#define ZYNQ_GPIO_NR_GPIOS (ZYNQ_GPIO_BANK0_NGPIO + \ - ZYNQ_GPIO_BANK1_NGPIO + \ - ZYNQ_GPIO_BANK2_NGPIO + \ - ZYNQ_GPIO_BANK3_NGPIO) +#define ZYNQMP_GPIO_BANK0_NGPIO 26 +#define ZYNQMP_GPIO_BANK1_NGPIO 26 +#define ZYNQMP_GPIO_BANK2_NGPIO 26 +#define ZYNQMP_GPIO_BANK3_NGPIO 32 +#define ZYNQMP_GPIO_BANK4_NGPIO 32 +#define ZYNQMP_GPIO_BANK5_NGPIO 32 -#define ZYNQ_GPIO_BANK0_PIN_MIN 0 -#define ZYNQ_GPIO_BANK0_PIN_MAX (ZYNQ_GPIO_BANK0_PIN_MIN + \ - ZYNQ_GPIO_BANK0_NGPIO - 1) -#define ZYNQ_GPIO_BANK1_PIN_MIN (ZYNQ_GPIO_BANK0_PIN_MAX + 1) -#define ZYNQ_GPIO_BANK1_PIN_MAX (ZYNQ_GPIO_BANK1_PIN_MIN + \ - ZYNQ_GPIO_BANK1_NGPIO - 1) -#define ZYNQ_GPIO_BANK2_PIN_MIN (ZYNQ_GPIO_BANK1_PIN_MAX + 1) -#define ZYNQ_GPIO_BANK2_PIN_MAX (ZYNQ_GPIO_BANK2_PIN_MIN + \ - ZYNQ_GPIO_BANK2_NGPIO - 1) -#define ZYNQ_GPIO_BANK3_PIN_MIN (ZYNQ_GPIO_BANK2_PIN_MAX + 1) -#define ZYNQ_GPIO_BANK3_PIN_MAX (ZYNQ_GPIO_BANK3_PIN_MIN + \ - ZYNQ_GPIO_BANK3_NGPIO - 1) +#define ZYNQ_GPIO_NR_GPIOS 118 +#define ZYNQMP_GPIO_NR_GPIOS 174 + +#define ZYNQ_GPIO_BANK0_PIN_MIN(str) 0 +#define ZYNQ_GPIO_BANK0_PIN_MAX(str) (ZYNQ_GPIO_BANK0_PIN_MIN(str) + \ + ZYNQ##str##_GPIO_BANK0_NGPIO - 1) +#define ZYNQ_GPIO_BANK1_PIN_MIN(str) (ZYNQ_GPIO_BANK0_PIN_MAX(str) + 1) +#define ZYNQ_GPIO_BANK1_PIN_MAX(str) (ZYNQ_GPIO_BANK1_PIN_MIN(str) + \ + ZYNQ##str##_GPIO_BANK1_NGPIO - 1) +#define ZYNQ_GPIO_BANK2_PIN_MIN(str) (ZYNQ_GPIO_BANK1_PIN_MAX(str) + 1) +#define ZYNQ_GPIO_BANK2_PIN_MAX(str) (ZYNQ_GPIO_BANK2_PIN_MIN(str) + \ + ZYNQ##str##_GPIO_BANK2_NGPIO - 1) +#define ZYNQ_GPIO_BANK3_PIN_MIN(str) (ZYNQ_GPIO_BANK2_PIN_MAX(str) + 1) +#define ZYNQ_GPIO_BANK3_PIN_MAX(str) (ZYNQ_GPIO_BANK3_PIN_MIN(str) + \ + ZYNQ##str##_GPIO_BANK3_NGPIO - 1) +#define ZYNQ_GPIO_BANK4_PIN_MIN(str) (ZYNQ_GPIO_BANK3_PIN_MAX(str) + 1) +#define ZYNQ_GPIO_BANK4_PIN_MAX(str) (ZYNQ_GPIO_BANK4_PIN_MIN(str) + \ + ZYNQ##str##_GPIO_BANK4_NGPIO - 1) +#define ZYNQ_GPIO_BANK5_PIN_MIN(str) (ZYNQ_GPIO_BANK4_PIN_MAX(str) + 1) +#define ZYNQ_GPIO_BANK5_PIN_MAX(str) (ZYNQ_GPIO_BANK5_PIN_MIN(str) + \ + ZYNQ##str##_GPIO_BANK5_NGPIO - 1) /* Register offsets for the GPIO device */ @@ -89,12 +102,30 @@ * @base_addr: base address of the GPIO device * @clk: clock resource for this controller * @irq: interrupt for the GPIO device + * @p_data: pointer to platform data */ struct zynq_gpio { struct gpio_chip chip; void __iomem *base_addr; struct clk *clk; int irq; + const struct zynq_platform_data *p_data; +}; + +/** + * struct zynq_platform_data - zynq gpio platform data structure + * @label: string to store in gpio->label + * @ngpio: max number of gpio pins + * @max_bank: maximum number of gpio banks + * @bank_min: this array represents bank's min pin + * @bank_max: this array represents bank's max pin +*/ +struct zynq_platform_data { + const char *label; + u16 ngpio; + int max_bank; + int bank_min[ZYNQMP_GPIO_MAX_BANK]; + int bank_max[ZYNQMP_GPIO_MAX_BANK]; }; static struct irq_chip zynq_gpio_level_irqchip; @@ -112,39 +143,26 @@ static struct irq_chip zynq_gpio_edge_irqchip; */ static inline void zynq_gpio_get_bank_pin(unsigned int pin_num, unsigned int *bank_num, - unsigned int *bank_pin_num) + unsigned int *bank_pin_num, + struct zynq_gpio *gpio) { - switch (pin_num) { - case ZYNQ_GPIO_BANK0_PIN_MIN ... ZYNQ_GPIO_BANK0_PIN_MAX: - *bank_num = 0; - *bank_pin_num = pin_num; - break; - case ZYNQ_GPIO_BANK1_PIN_MIN ... ZYNQ_GPIO_BANK1_PIN_MAX: - *bank_num = 1; - *bank_pin_num = pin_num - ZYNQ_GPIO_BANK1_PIN_MIN; - break; - case ZYNQ_GPIO_BANK2_PIN_MIN ... ZYNQ_GPIO_BANK2_PIN_MAX: - *bank_num = 2; - *bank_pin_num = pin_num - ZYNQ_GPIO_BANK2_PIN_MIN; - break; - case ZYNQ_GPIO_BANK3_PIN_MIN ... ZYNQ_GPIO_BANK3_PIN_MAX: - *bank_num = 3; - *bank_pin_num = pin_num - ZYNQ_GPIO_BANK3_PIN_MIN; - break; - default: - WARN(true, "invalid GPIO pin number: %u", pin_num); - *bank_num = 0; - *bank_pin_num = 0; - break; - } -} + int bank; -static const unsigned int zynq_gpio_bank_offset[] = { - ZYNQ_GPIO_BANK0_PIN_MIN, - ZYNQ_GPIO_BANK1_PIN_MIN, - ZYNQ_GPIO_BANK2_PIN_MIN, - ZYNQ_GPIO_BANK3_PIN_MIN, -}; + for (bank = 0; bank < gpio->p_data->max_bank; bank++) { + if ((pin_num >= gpio->p_data->bank_min[bank]) && + (pin_num <= gpio->p_data->bank_max[bank])) { + *bank_num = bank; + *bank_pin_num = pin_num - + gpio->p_data->bank_min[bank]; + return; + } + } + + /* default */ + WARN(true, "invalid GPIO pin number: %u", pin_num); + *bank_num = 0; + *bank_pin_num = 0; +} /** * zynq_gpio_get_value - Get the state of the specified pin of GPIO device @@ -161,7 +179,7 @@ static int zynq_gpio_get_value(struct gpio_chip *chip, unsigned int pin) unsigned int bank_num, bank_pin_num; struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip); - zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num); + zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); data = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DATA_RO_OFFSET(bank_num)); @@ -185,7 +203,7 @@ static void zynq_gpio_set_value(struct gpio_chip *chip, unsigned int pin, unsigned int reg_offset, bank_num, bank_pin_num; struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip); - zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num); + zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); if (bank_pin_num >= ZYNQ_GPIO_MID_PIN_NUM) { /* only 16 data bits in bit maskable reg */ @@ -222,7 +240,7 @@ static int zynq_gpio_dir_in(struct gpio_chip *chip, unsigned int pin) unsigned int bank_num, bank_pin_num; struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip); - zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num); + zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); /* bank 0 pins 7 and 8 are special and cannot be used as inputs */ if (bank_num == 0 && (bank_pin_num == 7 || bank_pin_num == 8)) @@ -255,7 +273,7 @@ static int zynq_gpio_dir_out(struct gpio_chip *chip, unsigned int pin, unsigned int bank_num, bank_pin_num; struct zynq_gpio *gpio = container_of(chip, struct zynq_gpio, chip); - zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num); + zynq_gpio_get_bank_pin(pin, &bank_num, &bank_pin_num, gpio); /* set the GPIO pin as output */ reg = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_DIRM_OFFSET(bank_num)); @@ -286,7 +304,7 @@ static void zynq_gpio_irq_mask(struct irq_data *irq_data) struct zynq_gpio *gpio = irq_data_get_irq_chip_data(irq_data); device_pin_num = irq_data->hwirq; - zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num); + zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio); writel_relaxed(BIT(bank_pin_num), gpio->base_addr + ZYNQ_GPIO_INTDIS_OFFSET(bank_num)); } @@ -306,7 +324,7 @@ static void zynq_gpio_irq_unmask(struct irq_data *irq_data) struct zynq_gpio *gpio = irq_data_get_irq_chip_data(irq_data); device_pin_num = irq_data->hwirq; - zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num); + zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio); writel_relaxed(BIT(bank_pin_num), gpio->base_addr + ZYNQ_GPIO_INTEN_OFFSET(bank_num)); } @@ -325,7 +343,7 @@ static void zynq_gpio_irq_ack(struct irq_data *irq_data) struct zynq_gpio *gpio = irq_data_get_irq_chip_data(irq_data); device_pin_num = irq_data->hwirq; - zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num); + zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio); writel_relaxed(BIT(bank_pin_num), gpio->base_addr + ZYNQ_GPIO_INTSTS_OFFSET(bank_num)); } @@ -335,7 +353,7 @@ static void zynq_gpio_irq_ack(struct irq_data *irq_data) * @irq_data: irq data containing irq number of gpio pin for the interrupt * to enable * - * Clears the INTSTS bit and unmasks the given interrrupt. + * Clears the INTSTS bit and unmasks the given interrupt. */ static void zynq_gpio_irq_enable(struct irq_data *irq_data) { @@ -375,7 +393,7 @@ static int zynq_gpio_set_irq_type(struct irq_data *irq_data, unsigned int type) struct zynq_gpio *gpio = irq_data_get_irq_chip_data(irq_data); device_pin_num = irq_data->hwirq; - zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num); + zynq_gpio_get_bank_pin(device_pin_num, &bank_num, &bank_pin_num, gpio); int_type = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_INTTYPE_OFFSET(bank_num)); @@ -470,7 +488,7 @@ static void zynq_gpio_handle_bank_irq(struct zynq_gpio *gpio, unsigned int bank_num, unsigned long pending) { - unsigned int bank_offset = zynq_gpio_bank_offset[bank_num]; + unsigned int bank_offset = gpio->p_data->bank_min[bank_num]; struct irq_domain *irqdomain = gpio->chip.irqdomain; int offset; @@ -505,7 +523,7 @@ static void zynq_gpio_irqhandler(unsigned int irq, struct irq_desc *desc) chained_irq_enter(irqchip, desc); - for (bank_num = 0; bank_num < ZYNQ_GPIO_MAX_BANK; bank_num++) { + for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) { int_sts = readl_relaxed(gpio->base_addr + ZYNQ_GPIO_INTSTS_OFFSET(bank_num)); int_enb = readl_relaxed(gpio->base_addr + @@ -582,6 +600,46 @@ static const struct dev_pm_ops zynq_gpio_dev_pm_ops = { zynq_gpio_runtime_resume, NULL) }; +static const struct zynq_platform_data zynqmp_gpio_def = { + .label = "zynqmp_gpio", + .ngpio = ZYNQMP_GPIO_NR_GPIOS, + .max_bank = ZYNQMP_GPIO_MAX_BANK, + .bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(MP), + .bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(MP), + .bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(MP), + .bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(MP), + .bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(MP), + .bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(MP), + .bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(MP), + .bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(MP), + .bank_min[4] = ZYNQ_GPIO_BANK4_PIN_MIN(MP), + .bank_max[4] = ZYNQ_GPIO_BANK4_PIN_MAX(MP), + .bank_min[5] = ZYNQ_GPIO_BANK5_PIN_MIN(MP), + .bank_max[5] = ZYNQ_GPIO_BANK5_PIN_MAX(MP), +}; + +static const struct zynq_platform_data zynq_gpio_def = { + .label = "zynq_gpio", + .ngpio = ZYNQ_GPIO_NR_GPIOS, + .max_bank = ZYNQ_GPIO_MAX_BANK, + .bank_min[0] = ZYNQ_GPIO_BANK0_PIN_MIN(), + .bank_max[0] = ZYNQ_GPIO_BANK0_PIN_MAX(), + .bank_min[1] = ZYNQ_GPIO_BANK1_PIN_MIN(), + .bank_max[1] = ZYNQ_GPIO_BANK1_PIN_MAX(), + .bank_min[2] = ZYNQ_GPIO_BANK2_PIN_MIN(), + .bank_max[2] = ZYNQ_GPIO_BANK2_PIN_MAX(), + .bank_min[3] = ZYNQ_GPIO_BANK3_PIN_MIN(), + .bank_max[3] = ZYNQ_GPIO_BANK3_PIN_MAX(), +}; + +static const struct of_device_id zynq_gpio_of_match[] = { + { .compatible = "xlnx,zynq-gpio-1.0", .data = (void *)&zynq_gpio_def }, + { .compatible = "xlnx,zynqmp-gpio-1.0", + .data = (void *)&zynqmp_gpio_def }, + { /* end of table */ } +}; +MODULE_DEVICE_TABLE(of, zynq_gpio_of_match); + /** * zynq_gpio_probe - Initialization method for a zynq_gpio device * @pdev: platform device instance @@ -599,11 +657,18 @@ static int zynq_gpio_probe(struct platform_device *pdev) struct zynq_gpio *gpio; struct gpio_chip *chip; struct resource *res; + const struct of_device_id *match; gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL); if (!gpio) return -ENOMEM; + match = of_match_node(zynq_gpio_of_match, pdev->dev.of_node); + if (!match) { + dev_err(&pdev->dev, "of_match_node() failed\n"); + return -EINVAL; + } + gpio->p_data = match->data; platform_set_drvdata(pdev, gpio); res = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -619,7 +684,7 @@ static int zynq_gpio_probe(struct platform_device *pdev) /* configure the gpio chip */ chip = &gpio->chip; - chip->label = "zynq_gpio"; + chip->label = gpio->p_data->label; chip->owner = THIS_MODULE; chip->dev = &pdev->dev; chip->get = zynq_gpio_get_value; @@ -629,7 +694,7 @@ static int zynq_gpio_probe(struct platform_device *pdev) chip->direction_input = zynq_gpio_dir_in; chip->direction_output = zynq_gpio_dir_out; chip->base = -1; - chip->ngpio = ZYNQ_GPIO_NR_GPIOS; + chip->ngpio = gpio->p_data->ngpio; /* Enable GPIO clock */ gpio->clk = devm_clk_get(&pdev->dev, NULL); @@ -651,7 +716,7 @@ static int zynq_gpio_probe(struct platform_device *pdev) } /* disable interrupts for all banks */ - for (bank_num = 0; bank_num < ZYNQ_GPIO_MAX_BANK; bank_num++) + for (bank_num = 0; bank_num < gpio->p_data->max_bank; bank_num++) writel_relaxed(ZYNQ_GPIO_IXR_DISABLE_ALL, gpio->base_addr + ZYNQ_GPIO_INTDIS_OFFSET(bank_num)); @@ -695,12 +760,6 @@ static int zynq_gpio_remove(struct platform_device *pdev) return 0; } -static struct of_device_id zynq_gpio_of_match[] = { - { .compatible = "xlnx,zynq-gpio-1.0", }, - { /* end of table */ } -}; -MODULE_DEVICE_TABLE(of, zynq_gpio_of_match); - static struct platform_driver zynq_gpio_driver = { .driver = { .name = DRIVER_NAME, diff --git a/drivers/gpio/gpiolib-acpi.c b/drivers/gpio/gpiolib-acpi.c index 725d16138b74..533fe5dbe6f8 100644 --- a/drivers/gpio/gpiolib-acpi.c +++ b/drivers/gpio/gpiolib-acpi.c @@ -114,10 +114,11 @@ static inline int acpi_gpiochip_pin_to_gpio_offset(struct gpio_chip *chip, * @path: ACPI GPIO controller full path name, (e.g. "\\_SB.GPO1") * @pin: ACPI GPIO pin number (0-based, controller-relative) * - * Returns GPIO descriptor to use with Linux generic GPIO API, or ERR_PTR - * error value + * Return: GPIO descriptor to use with Linux generic GPIO API, or ERR_PTR + * error value. Specifically returns %-EPROBE_DEFER if the referenced GPIO + * controller does not have gpiochip registered at the moment. This is to + * support probe deferral. */ - static struct gpio_desc *acpi_get_gpiod(char *path, int pin) { struct gpio_chip *chip; @@ -131,7 +132,7 @@ static struct gpio_desc *acpi_get_gpiod(char *path, int pin) chip = gpiochip_find(handle, acpi_gpiochip_find); if (!chip) - return ERR_PTR(-ENODEV); + return ERR_PTR(-EPROBE_DEFER); offset = acpi_gpiochip_pin_to_gpio_offset(chip, pin); if (offset < 0) @@ -307,6 +308,7 @@ void acpi_gpiochip_request_interrupts(struct gpio_chip *chip) acpi_walk_resources(handle, "_AEI", acpi_gpiochip_request_interrupt, acpi_gpio); } +EXPORT_SYMBOL_GPL(acpi_gpiochip_request_interrupts); /** * acpi_gpiochip_free_interrupts() - Free GPIO ACPI event interrupts. @@ -346,6 +348,7 @@ void acpi_gpiochip_free_interrupts(struct gpio_chip *chip) kfree(event); } } +EXPORT_SYMBOL_GPL(acpi_gpiochip_free_interrupts); int acpi_dev_add_driver_gpios(struct acpi_device *adev, const struct acpi_gpio_mapping *gpios) @@ -514,6 +517,35 @@ struct gpio_desc *acpi_get_gpiod_by_index(struct acpi_device *adev, return lookup.desc ? lookup.desc : ERR_PTR(-ENOENT); } +/** + * acpi_dev_gpio_irq_get() - Find GpioInt and translate it to Linux IRQ number + * @adev: pointer to a ACPI device to get IRQ from + * @index: index of GpioInt resource (starting from %0) + * + * If the device has one or more GpioInt resources, this function can be + * used to translate from the GPIO offset in the resource to the Linux IRQ + * number. + * + * Return: Linux IRQ number (>%0) on success, negative errno on failure. + */ +int acpi_dev_gpio_irq_get(struct acpi_device *adev, int index) +{ + int idx, i; + + for (i = 0, idx = 0; idx <= index; i++) { + struct acpi_gpio_info info; + struct gpio_desc *desc; + + desc = acpi_get_gpiod_by_index(adev, NULL, i, &info); + if (IS_ERR(desc)) + break; + if (info.gpioint && idx++ == index) + return gpiod_to_irq(desc); + } + return -ENOENT; +} +EXPORT_SYMBOL_GPL(acpi_dev_gpio_irq_get); + static acpi_status acpi_gpio_adr_space_handler(u32 function, acpi_physical_address address, u32 bits, u64 *value, void *handler_context, diff --git a/drivers/gpio/gpiolib-of.c b/drivers/gpio/gpiolib-of.c index a6c67c6b4680..9a0ec48a4737 100644 --- a/drivers/gpio/gpiolib-of.c +++ b/drivers/gpio/gpiolib-of.c @@ -242,7 +242,7 @@ int of_gpio_simple_xlate(struct gpio_chip *gc, { /* * We're discouraging gpio_cells < 2, since that way you'll have to - * write your own xlate function (that will have to retrive the GPIO + * write your own xlate function (that will have to retrieve the GPIO * number and the flags from a single gpio cell -- this is possible, * but not recommended). */ diff --git a/drivers/gpio/gpiolib-sysfs.c b/drivers/gpio/gpiolib-sysfs.c index af3bc7a8033b..b57ed8e55ab5 100644 --- a/drivers/gpio/gpiolib-sysfs.c +++ b/drivers/gpio/gpiolib-sysfs.c @@ -6,14 +6,29 @@ #include #include #include +#include #include "gpiolib.h" -static DEFINE_IDR(dirent_idr); +#define GPIO_IRQF_TRIGGER_FALLING BIT(0) +#define GPIO_IRQF_TRIGGER_RISING BIT(1) +#define GPIO_IRQF_TRIGGER_BOTH (GPIO_IRQF_TRIGGER_FALLING | \ + GPIO_IRQF_TRIGGER_RISING) +struct gpiod_data { + struct gpio_desc *desc; -/* lock protects against unexport_gpio() being called while - * sysfs files are active. + struct mutex mutex; + struct kernfs_node *value_kn; + int irq; + unsigned char irq_flags; + + bool direction_can_change; +}; + +/* + * Lock to serialise gpiod export and unexport, and prevent re-export of + * gpiod whose chip is being unregistered. */ static DEFINE_MUTEX(sysfs_lock); @@ -38,38 +53,35 @@ static DEFINE_MUTEX(sysfs_lock); * /edge configuration */ -static ssize_t gpio_direction_show(struct device *dev, +static ssize_t direction_show(struct device *dev, struct device_attribute *attr, char *buf) { - struct gpio_desc *desc = dev_get_drvdata(dev); + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; ssize_t status; - mutex_lock(&sysfs_lock); + mutex_lock(&data->mutex); - if (!test_bit(FLAG_EXPORT, &desc->flags)) { - status = -EIO; - } else { - gpiod_get_direction(desc); - status = sprintf(buf, "%s\n", + gpiod_get_direction(desc); + status = sprintf(buf, "%s\n", test_bit(FLAG_IS_OUT, &desc->flags) ? "out" : "in"); - } - mutex_unlock(&sysfs_lock); + mutex_unlock(&data->mutex); + return status; } -static ssize_t gpio_direction_store(struct device *dev, +static ssize_t direction_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t size) { - struct gpio_desc *desc = dev_get_drvdata(dev); + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; ssize_t status; - mutex_lock(&sysfs_lock); + mutex_lock(&data->mutex); - if (!test_bit(FLAG_EXPORT, &desc->flags)) - status = -EIO; - else if (sysfs_streq(buf, "high")) + if (sysfs_streq(buf, "high")) status = gpiod_direction_output_raw(desc, 1); else if (sysfs_streq(buf, "out") || sysfs_streq(buf, "low")) status = gpiod_direction_output_raw(desc, 0); @@ -78,43 +90,40 @@ static ssize_t gpio_direction_store(struct device *dev, else status = -EINVAL; - mutex_unlock(&sysfs_lock); + mutex_unlock(&data->mutex); + return status ? : size; } +static DEVICE_ATTR_RW(direction); -static /* const */ DEVICE_ATTR(direction, 0644, - gpio_direction_show, gpio_direction_store); - -static ssize_t gpio_value_show(struct device *dev, +static ssize_t value_show(struct device *dev, struct device_attribute *attr, char *buf) { - struct gpio_desc *desc = dev_get_drvdata(dev); + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; ssize_t status; - mutex_lock(&sysfs_lock); + mutex_lock(&data->mutex); - if (!test_bit(FLAG_EXPORT, &desc->flags)) - status = -EIO; - else - status = sprintf(buf, "%d\n", gpiod_get_value_cansleep(desc)); + status = sprintf(buf, "%d\n", gpiod_get_value_cansleep(desc)); + + mutex_unlock(&data->mutex); - mutex_unlock(&sysfs_lock); return status; } -static ssize_t gpio_value_store(struct device *dev, +static ssize_t value_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t size) { - struct gpio_desc *desc = dev_get_drvdata(dev); + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; ssize_t status; - mutex_lock(&sysfs_lock); + mutex_lock(&data->mutex); - if (!test_bit(FLAG_EXPORT, &desc->flags)) - status = -EIO; - else if (!test_bit(FLAG_IS_OUT, &desc->flags)) + if (!test_bit(FLAG_IS_OUT, &desc->flags)) { status = -EPERM; - else { + } else { long value; status = kstrtol(buf, 0, &value); @@ -124,172 +133,168 @@ static ssize_t gpio_value_store(struct device *dev, } } - mutex_unlock(&sysfs_lock); + mutex_unlock(&data->mutex); + return status; } - -static DEVICE_ATTR(value, 0644, - gpio_value_show, gpio_value_store); +static DEVICE_ATTR_RW(value); static irqreturn_t gpio_sysfs_irq(int irq, void *priv) { - struct kernfs_node *value_sd = priv; + struct gpiod_data *data = priv; + + sysfs_notify_dirent(data->value_kn); - sysfs_notify_dirent(value_sd); return IRQ_HANDLED; } -static int gpio_setup_irq(struct gpio_desc *desc, struct device *dev, - unsigned long gpio_flags) +/* Caller holds gpiod-data mutex. */ +static int gpio_sysfs_request_irq(struct device *dev, unsigned char flags) { - struct kernfs_node *value_sd; + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; unsigned long irq_flags; - int ret, irq, id; + int ret; - if ((desc->flags & GPIO_TRIGGER_MASK) == gpio_flags) - return 0; - - irq = gpiod_to_irq(desc); - if (irq < 0) + data->irq = gpiod_to_irq(desc); + if (data->irq < 0) return -EIO; - id = desc->flags >> ID_SHIFT; - value_sd = idr_find(&dirent_idr, id); - if (value_sd) - free_irq(irq, value_sd); - - desc->flags &= ~GPIO_TRIGGER_MASK; - - if (!gpio_flags) { - gpiochip_unlock_as_irq(desc->chip, gpio_chip_hwgpio(desc)); - ret = 0; - goto free_id; - } + data->value_kn = sysfs_get_dirent(dev->kobj.sd, "value"); + if (!data->value_kn) + return -ENODEV; irq_flags = IRQF_SHARED; - if (test_bit(FLAG_TRIG_FALL, &gpio_flags)) + if (flags & GPIO_IRQF_TRIGGER_FALLING) irq_flags |= test_bit(FLAG_ACTIVE_LOW, &desc->flags) ? IRQF_TRIGGER_RISING : IRQF_TRIGGER_FALLING; - if (test_bit(FLAG_TRIG_RISE, &gpio_flags)) + if (flags & GPIO_IRQF_TRIGGER_RISING) irq_flags |= test_bit(FLAG_ACTIVE_LOW, &desc->flags) ? IRQF_TRIGGER_FALLING : IRQF_TRIGGER_RISING; - if (!value_sd) { - value_sd = sysfs_get_dirent(dev->kobj.sd, "value"); - if (!value_sd) { - ret = -ENODEV; - goto err_out; - } - - ret = idr_alloc(&dirent_idr, value_sd, 1, 0, GFP_KERNEL); - if (ret < 0) - goto free_sd; - id = ret; - - desc->flags &= GPIO_FLAGS_MASK; - desc->flags |= (unsigned long)id << ID_SHIFT; - - if (desc->flags >> ID_SHIFT != id) { - ret = -ERANGE; - goto free_id; - } - } - - ret = request_any_context_irq(irq, gpio_sysfs_irq, irq_flags, - "gpiolib", value_sd); - if (ret < 0) - goto free_id; - + /* + * FIXME: This should be done in the irq_request_resources callback + * when the irq is requested, but a few drivers currently fail + * to do so. + * + * Remove this redundant call (along with the corresponding + * unlock) when those drivers have been fixed. + */ ret = gpiochip_lock_as_irq(desc->chip, gpio_chip_hwgpio(desc)); - if (ret < 0) { - gpiod_warn(desc, "failed to flag the GPIO for IRQ\n"); - goto free_id; - } + if (ret < 0) + goto err_put_kn; + + ret = request_any_context_irq(data->irq, gpio_sysfs_irq, irq_flags, + "gpiolib", data); + if (ret < 0) + goto err_unlock; + + data->irq_flags = flags; - desc->flags |= gpio_flags; return 0; -free_id: - idr_remove(&dirent_idr, id); - desc->flags &= GPIO_FLAGS_MASK; -free_sd: - if (value_sd) - sysfs_put(value_sd); -err_out: +err_unlock: + gpiochip_unlock_as_irq(desc->chip, gpio_chip_hwgpio(desc)); +err_put_kn: + sysfs_put(data->value_kn); + return ret; } +/* + * Caller holds gpiod-data mutex (unless called after class-device + * deregistration). + */ +static void gpio_sysfs_free_irq(struct device *dev) +{ + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; + + data->irq_flags = 0; + free_irq(data->irq, data); + gpiochip_unlock_as_irq(desc->chip, gpio_chip_hwgpio(desc)); + sysfs_put(data->value_kn); +} + static const struct { const char *name; - unsigned long flags; + unsigned char flags; } trigger_types[] = { { "none", 0 }, - { "falling", BIT(FLAG_TRIG_FALL) }, - { "rising", BIT(FLAG_TRIG_RISE) }, - { "both", BIT(FLAG_TRIG_FALL) | BIT(FLAG_TRIG_RISE) }, + { "falling", GPIO_IRQF_TRIGGER_FALLING }, + { "rising", GPIO_IRQF_TRIGGER_RISING }, + { "both", GPIO_IRQF_TRIGGER_BOTH }, }; -static ssize_t gpio_edge_show(struct device *dev, +static ssize_t edge_show(struct device *dev, struct device_attribute *attr, char *buf) { - const struct gpio_desc *desc = dev_get_drvdata(dev); - ssize_t status; + struct gpiod_data *data = dev_get_drvdata(dev); + ssize_t status = 0; + int i; - mutex_lock(&sysfs_lock); + mutex_lock(&data->mutex); - if (!test_bit(FLAG_EXPORT, &desc->flags)) - status = -EIO; - else { - int i; - - status = 0; - for (i = 0; i < ARRAY_SIZE(trigger_types); i++) - if ((desc->flags & GPIO_TRIGGER_MASK) - == trigger_types[i].flags) { - status = sprintf(buf, "%s\n", - trigger_types[i].name); - break; - } + for (i = 0; i < ARRAY_SIZE(trigger_types); i++) { + if (data->irq_flags == trigger_types[i].flags) { + status = sprintf(buf, "%s\n", trigger_types[i].name); + break; + } } - mutex_unlock(&sysfs_lock); + mutex_unlock(&data->mutex); + return status; } -static ssize_t gpio_edge_store(struct device *dev, +static ssize_t edge_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t size) { - struct gpio_desc *desc = dev_get_drvdata(dev); - ssize_t status; - int i; + struct gpiod_data *data = dev_get_drvdata(dev); + unsigned char flags; + ssize_t status = size; + int i; - for (i = 0; i < ARRAY_SIZE(trigger_types); i++) + for (i = 0; i < ARRAY_SIZE(trigger_types); i++) { if (sysfs_streq(trigger_types[i].name, buf)) - goto found; - return -EINVAL; + break; + } -found: - mutex_lock(&sysfs_lock); + if (i == ARRAY_SIZE(trigger_types)) + return -EINVAL; - if (!test_bit(FLAG_EXPORT, &desc->flags)) - status = -EIO; - else { - status = gpio_setup_irq(desc, dev, trigger_types[i].flags); + flags = trigger_types[i].flags; + + mutex_lock(&data->mutex); + + if (flags == data->irq_flags) { + status = size; + goto out_unlock; + } + + if (data->irq_flags) + gpio_sysfs_free_irq(dev); + + if (flags) { + status = gpio_sysfs_request_irq(dev, flags); if (!status) status = size; } - mutex_unlock(&sysfs_lock); +out_unlock: + mutex_unlock(&data->mutex); return status; } +static DEVICE_ATTR_RW(edge); -static DEVICE_ATTR(edge, 0644, gpio_edge_show, gpio_edge_store); - -static int sysfs_set_active_low(struct gpio_desc *desc, struct device *dev, - int value) +/* Caller holds gpiod-data mutex. */ +static int gpio_sysfs_set_active_low(struct device *dev, int value) { + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; int status = 0; + unsigned int flags = data->irq_flags; if (!!test_bit(FLAG_ACTIVE_LOW, &desc->flags) == !!value) return 0; @@ -300,69 +305,59 @@ static int sysfs_set_active_low(struct gpio_desc *desc, struct device *dev, clear_bit(FLAG_ACTIVE_LOW, &desc->flags); /* reconfigure poll(2) support if enabled on one edge only */ - if (dev != NULL && (!!test_bit(FLAG_TRIG_RISE, &desc->flags) ^ - !!test_bit(FLAG_TRIG_FALL, &desc->flags))) { - unsigned long trigger_flags = desc->flags & GPIO_TRIGGER_MASK; - - gpio_setup_irq(desc, dev, 0); - status = gpio_setup_irq(desc, dev, trigger_flags); + if (flags == GPIO_IRQF_TRIGGER_FALLING || + flags == GPIO_IRQF_TRIGGER_RISING) { + gpio_sysfs_free_irq(dev); + status = gpio_sysfs_request_irq(dev, flags); } return status; } -static ssize_t gpio_active_low_show(struct device *dev, +static ssize_t active_low_show(struct device *dev, struct device_attribute *attr, char *buf) { - const struct gpio_desc *desc = dev_get_drvdata(dev); + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; ssize_t status; - mutex_lock(&sysfs_lock); + mutex_lock(&data->mutex); - if (!test_bit(FLAG_EXPORT, &desc->flags)) - status = -EIO; - else - status = sprintf(buf, "%d\n", + status = sprintf(buf, "%d\n", !!test_bit(FLAG_ACTIVE_LOW, &desc->flags)); - mutex_unlock(&sysfs_lock); + mutex_unlock(&data->mutex); return status; } -static ssize_t gpio_active_low_store(struct device *dev, +static ssize_t active_low_store(struct device *dev, struct device_attribute *attr, const char *buf, size_t size) { - struct gpio_desc *desc = dev_get_drvdata(dev); + struct gpiod_data *data = dev_get_drvdata(dev); ssize_t status; + long value; - mutex_lock(&sysfs_lock); + mutex_lock(&data->mutex); - if (!test_bit(FLAG_EXPORT, &desc->flags)) { - status = -EIO; - } else { - long value; + status = kstrtol(buf, 0, &value); + if (status == 0) + status = gpio_sysfs_set_active_low(dev, value); - status = kstrtol(buf, 0, &value); - if (status == 0) - status = sysfs_set_active_low(desc, dev, value != 0); - } - - mutex_unlock(&sysfs_lock); + mutex_unlock(&data->mutex); return status ? : size; } - -static DEVICE_ATTR(active_low, 0644, - gpio_active_low_show, gpio_active_low_store); +static DEVICE_ATTR_RW(active_low); static umode_t gpio_is_visible(struct kobject *kobj, struct attribute *attr, int n) { struct device *dev = container_of(kobj, struct device, kobj); - struct gpio_desc *desc = dev_get_drvdata(dev); + struct gpiod_data *data = dev_get_drvdata(dev); + struct gpio_desc *desc = data->desc; umode_t mode = attr->mode; - bool show_direction = test_bit(FLAG_SYSFS_DIR, &desc->flags); + bool show_direction = data->direction_can_change; if (attr == &dev_attr_direction.attr) { if (!show_direction) @@ -402,32 +397,32 @@ static const struct attribute_group *gpio_groups[] = { * /ngpio ... matching gpio_chip.ngpio */ -static ssize_t chip_base_show(struct device *dev, +static ssize_t base_show(struct device *dev, struct device_attribute *attr, char *buf) { const struct gpio_chip *chip = dev_get_drvdata(dev); return sprintf(buf, "%d\n", chip->base); } -static DEVICE_ATTR(base, 0444, chip_base_show, NULL); +static DEVICE_ATTR_RO(base); -static ssize_t chip_label_show(struct device *dev, +static ssize_t label_show(struct device *dev, struct device_attribute *attr, char *buf) { const struct gpio_chip *chip = dev_get_drvdata(dev); return sprintf(buf, "%s\n", chip->label ? : ""); } -static DEVICE_ATTR(label, 0444, chip_label_show, NULL); +static DEVICE_ATTR_RO(label); -static ssize_t chip_ngpio_show(struct device *dev, +static ssize_t ngpio_show(struct device *dev, struct device_attribute *attr, char *buf) { const struct gpio_chip *chip = dev_get_drvdata(dev); return sprintf(buf, "%u\n", chip->ngpio); } -static DEVICE_ATTR(ngpio, 0444, chip_ngpio_show, NULL); +static DEVICE_ATTR_RO(ngpio); static struct attribute *gpiochip_attrs[] = { &dev_attr_base.attr, @@ -552,6 +547,7 @@ static struct class gpio_class = { int gpiod_export(struct gpio_desc *desc, bool direction_may_change) { struct gpio_chip *chip; + struct gpiod_data *data; unsigned long flags; int status; const char *ioname = NULL; @@ -574,9 +570,9 @@ int gpiod_export(struct gpio_desc *desc, bool direction_may_change) mutex_lock(&sysfs_lock); /* check if chip is being removed */ - if (!chip || !chip->exported) { + if (!chip || !chip->cdev) { status = -ENODEV; - goto fail_unlock; + goto err_unlock; } spin_lock_irqsave(&gpio_lock, flags); @@ -588,43 +584,54 @@ int gpiod_export(struct gpio_desc *desc, bool direction_may_change) test_bit(FLAG_REQUESTED, &desc->flags), test_bit(FLAG_EXPORT, &desc->flags)); status = -EPERM; - goto fail_unlock; + goto err_unlock; } - - if (desc->chip->direction_input && desc->chip->direction_output && - direction_may_change) { - set_bit(FLAG_SYSFS_DIR, &desc->flags); - } - spin_unlock_irqrestore(&gpio_lock, flags); - offset = gpio_chip_hwgpio(desc); - if (desc->chip->names && desc->chip->names[offset]) - ioname = desc->chip->names[offset]; + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (!data) { + status = -ENOMEM; + goto err_unlock; + } - dev = device_create_with_groups(&gpio_class, desc->chip->dev, - MKDEV(0, 0), desc, gpio_groups, + data->desc = desc; + mutex_init(&data->mutex); + if (chip->direction_input && chip->direction_output) + data->direction_can_change = direction_may_change; + else + data->direction_can_change = false; + + offset = gpio_chip_hwgpio(desc); + if (chip->names && chip->names[offset]) + ioname = chip->names[offset]; + + dev = device_create_with_groups(&gpio_class, chip->dev, + MKDEV(0, 0), data, gpio_groups, ioname ? ioname : "gpio%u", desc_to_gpio(desc)); if (IS_ERR(dev)) { status = PTR_ERR(dev); - goto fail_unlock; + goto err_free_data; } set_bit(FLAG_EXPORT, &desc->flags); mutex_unlock(&sysfs_lock); return 0; -fail_unlock: +err_free_data: + kfree(data); +err_unlock: mutex_unlock(&sysfs_lock); gpiod_dbg(desc, "%s: status %d\n", __func__, status); return status; } EXPORT_SYMBOL_GPL(gpiod_export); -static int match_export(struct device *dev, const void *data) +static int match_export(struct device *dev, const void *desc) { - return dev_get_drvdata(dev) == data; + struct gpiod_data *data = dev_get_drvdata(dev); + + return data->desc == desc; } /** @@ -641,81 +648,25 @@ static int match_export(struct device *dev, const void *data) int gpiod_export_link(struct device *dev, const char *name, struct gpio_desc *desc) { - int status = -EINVAL; + struct device *cdev; + int ret; if (!desc) { pr_warn("%s: invalid GPIO\n", __func__); return -EINVAL; } - mutex_lock(&sysfs_lock); + cdev = class_find_device(&gpio_class, NULL, desc, match_export); + if (!cdev) + return -ENODEV; - if (test_bit(FLAG_EXPORT, &desc->flags)) { - struct device *tdev; + ret = sysfs_create_link(&dev->kobj, &cdev->kobj, name); + put_device(cdev); - tdev = class_find_device(&gpio_class, NULL, desc, match_export); - if (tdev != NULL) { - status = sysfs_create_link(&dev->kobj, &tdev->kobj, - name); - put_device(tdev); - } else { - status = -ENODEV; - } - } - - mutex_unlock(&sysfs_lock); - - if (status) - gpiod_dbg(desc, "%s: status %d\n", __func__, status); - - return status; + return ret; } EXPORT_SYMBOL_GPL(gpiod_export_link); -/** - * gpiod_sysfs_set_active_low - set the polarity of gpio sysfs value - * @gpio: gpio to change - * @value: non-zero to use active low, i.e. inverted values - * - * Set the polarity of /sys/class/gpio/gpioN/value sysfs attribute. - * The GPIO does not have to be exported yet. If poll(2) support has - * been enabled for either rising or falling edge, it will be - * reconfigured to follow the new polarity. - * - * Returns zero on success, else an error. - */ -int gpiod_sysfs_set_active_low(struct gpio_desc *desc, int value) -{ - struct device *dev = NULL; - int status = -EINVAL; - - if (!desc) { - pr_warn("%s: invalid GPIO\n", __func__); - return -EINVAL; - } - - mutex_lock(&sysfs_lock); - - if (test_bit(FLAG_EXPORT, &desc->flags)) { - dev = class_find_device(&gpio_class, NULL, desc, match_export); - if (dev == NULL) { - status = -ENODEV; - goto unlock; - } - } - - status = sysfs_set_active_low(desc, dev, value); - put_device(dev); -unlock: - mutex_unlock(&sysfs_lock); - - if (status) - gpiod_dbg(desc, "%s: status %d\n", __func__, status); - - return status; -} -EXPORT_SYMBOL_GPL(gpiod_sysfs_set_active_low); - /** * gpiod_unexport - reverse effect of gpio_export() * @gpio: gpio to make unavailable @@ -724,8 +675,8 @@ EXPORT_SYMBOL_GPL(gpiod_sysfs_set_active_low); */ void gpiod_unexport(struct gpio_desc *desc) { - int status = 0; - struct device *dev = NULL; + struct gpiod_data *data; + struct device *dev; if (!desc) { pr_warn("%s: invalid GPIO\n", __func__); @@ -734,81 +685,78 @@ void gpiod_unexport(struct gpio_desc *desc) mutex_lock(&sysfs_lock); - if (test_bit(FLAG_EXPORT, &desc->flags)) { + if (!test_bit(FLAG_EXPORT, &desc->flags)) + goto err_unlock; - dev = class_find_device(&gpio_class, NULL, desc, match_export); - if (dev) { - gpio_setup_irq(desc, dev, 0); - clear_bit(FLAG_SYSFS_DIR, &desc->flags); - clear_bit(FLAG_EXPORT, &desc->flags); - } else - status = -ENODEV; - } + dev = class_find_device(&gpio_class, NULL, desc, match_export); + if (!dev) + goto err_unlock; + + data = dev_get_drvdata(dev); + + clear_bit(FLAG_EXPORT, &desc->flags); + + device_unregister(dev); + + /* + * Release irq after deregistration to prevent race with edge_store. + */ + if (data->irq_flags) + gpio_sysfs_free_irq(dev); mutex_unlock(&sysfs_lock); - if (dev) { - device_unregister(dev); - put_device(dev); - } + put_device(dev); + kfree(data); - if (status) - gpiod_dbg(desc, "%s: status %d\n", __func__, status); + return; + +err_unlock: + mutex_unlock(&sysfs_lock); } EXPORT_SYMBOL_GPL(gpiod_unexport); -int gpiochip_export(struct gpio_chip *chip) +int gpiochip_sysfs_register(struct gpio_chip *chip) { - int status; struct device *dev; - /* Many systems register gpio chips for SOC support very early, + /* + * Many systems add gpio chips for SOC support very early, * before driver model support is available. In those cases we - * export this later, in gpiolib_sysfs_init() ... here we just + * register later, in gpiolib_sysfs_init() ... here we just * verify that _some_ field of gpio_class got initialized. */ if (!gpio_class.p) return 0; /* use chip->base for the ID; it's already known to be unique */ - mutex_lock(&sysfs_lock); dev = device_create_with_groups(&gpio_class, chip->dev, MKDEV(0, 0), chip, gpiochip_groups, "gpiochip%d", chip->base); if (IS_ERR(dev)) - status = PTR_ERR(dev); - else - status = 0; - chip->exported = (status == 0); + return PTR_ERR(dev); + + mutex_lock(&sysfs_lock); + chip->cdev = dev; mutex_unlock(&sysfs_lock); - if (status) - chip_dbg(chip, "%s: status %d\n", __func__, status); - - return status; + return 0; } -void gpiochip_unexport(struct gpio_chip *chip) +void gpiochip_sysfs_unregister(struct gpio_chip *chip) { - int status; - struct device *dev; struct gpio_desc *desc; unsigned int i; - mutex_lock(&sysfs_lock); - dev = class_find_device(&gpio_class, NULL, chip, match_export); - if (dev) { - put_device(dev); - device_unregister(dev); - /* prevent further gpiod exports */ - chip->exported = false; - status = 0; - } else - status = -ENODEV; - mutex_unlock(&sysfs_lock); + if (!chip->cdev) + return; - if (status) - chip_dbg(chip, "%s: status %d\n", __func__, status); + device_unregister(chip->cdev); + + /* prevent further gpiod exports */ + mutex_lock(&sysfs_lock); + chip->cdev = NULL; + mutex_unlock(&sysfs_lock); /* unregister gpiod class devices owned by sysfs */ for (i = 0; i < chip->ngpio; i++) { @@ -836,19 +784,20 @@ static int __init gpiolib_sysfs_init(void) */ spin_lock_irqsave(&gpio_lock, flags); list_for_each_entry(chip, &gpio_chips, list) { - if (chip->exported) + if (chip->cdev) continue; /* - * TODO we yield gpio_lock here because gpiochip_export() - * acquires a mutex. This is unsafe and needs to be fixed. + * TODO we yield gpio_lock here because + * gpiochip_sysfs_register() acquires a mutex. This is unsafe + * and needs to be fixed. * * Also it would be nice to use gpiochip_find() here so we * can keep gpio_chips local to gpiolib.c, but the yield of * gpio_lock prevents us from doing this. */ spin_unlock_irqrestore(&gpio_lock, flags); - status = gpiochip_export(chip); + status = gpiochip_sysfs_register(chip); spin_lock_irqsave(&gpio_lock, flags); } spin_unlock_irqrestore(&gpio_lock, flags); diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c index 6bc612b8a49f..be42ab368a80 100644 --- a/drivers/gpio/gpiolib.c +++ b/drivers/gpio/gpiolib.c @@ -290,7 +290,7 @@ int gpiochip_add(struct gpio_chip *chip) of_gpiochip_add(chip); acpi_gpiochip_add(chip); - status = gpiochip_export(chip); + status = gpiochip_sysfs_register(chip); if (status) goto err_remove_chip; @@ -327,10 +327,12 @@ EXPORT_SYMBOL_GPL(gpiochip_add); */ void gpiochip_remove(struct gpio_chip *chip) { + struct gpio_desc *desc; unsigned long flags; unsigned id; + bool requested = false; - gpiochip_unexport(chip); + gpiochip_sysfs_unregister(chip); gpiochip_irqchip_remove(chip); @@ -341,15 +343,17 @@ void gpiochip_remove(struct gpio_chip *chip) spin_lock_irqsave(&gpio_lock, flags); for (id = 0; id < chip->ngpio; id++) { - if (test_bit(FLAG_REQUESTED, &chip->desc[id].flags)) - dev_crit(chip->dev, "REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED\n"); + desc = &chip->desc[id]; + desc->chip = NULL; + if (test_bit(FLAG_REQUESTED, &desc->flags)) + requested = true; } - for (id = 0; id < chip->ngpio; id++) - chip->desc[id].chip = NULL; - list_del(&chip->list); spin_unlock_irqrestore(&gpio_lock, flags); + if (requested) + dev_crit(chip->dev, "REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED\n"); + kfree(chip->desc); chip->desc = NULL; } @@ -441,6 +445,8 @@ void gpiochip_set_chained_irqchip(struct gpio_chip *gpiochip, */ irq_set_handler_data(parent_irq, gpiochip); irq_set_chained_handler(parent_irq, parent_handler); + + gpiochip->irq_parent = parent_irq; } /* Set the parent IRQ for all affected IRQs */ @@ -549,6 +555,11 @@ static void gpiochip_irqchip_remove(struct gpio_chip *gpiochip) acpi_gpiochip_free_interrupts(gpiochip); + if (gpiochip->irq_parent) { + irq_set_chained_handler(gpiochip->irq_parent, NULL); + irq_set_handler_data(gpiochip->irq_parent, NULL); + } + /* Remove all IRQ mappings and delete the domain */ if (gpiochip->irqdomain) { for (offset = 0; offset < gpiochip->ngpio; offset++) @@ -608,7 +619,7 @@ int gpiochip_irqchip_add(struct gpio_chip *gpiochip, of_node = gpiochip->dev->of_node; #ifdef CONFIG_OF_GPIO /* - * If the gpiochip has an assigned OF node this takes precendence + * If the gpiochip has an assigned OF node this takes precedence * FIXME: get rid of this and use gpiochip->dev->of_node everywhere */ if (gpiochip->of_node) @@ -1211,7 +1222,7 @@ EXPORT_SYMBOL_GPL(gpiod_get_value); /* * _gpio_set_open_drain_value() - Set the open drain gpio's value. * @desc: gpio descriptor whose state need to be set. - * @value: Non-zero for setting it HIGH otherise it will set to LOW. + * @value: Non-zero for setting it HIGH otherwise it will set to LOW. */ static void _gpio_set_open_drain_value(struct gpio_desc *desc, bool value) { @@ -1238,7 +1249,7 @@ static void _gpio_set_open_drain_value(struct gpio_desc *desc, bool value) /* * _gpio_set_open_source_value() - Set the open source gpio's value. * @desc: gpio descriptor whose state need to be set. - * @value: Non-zero for setting it HIGH otherise it will set to LOW. + * @value: Non-zero for setting it HIGH otherwise it will set to LOW. */ static void _gpio_set_open_source_value(struct gpio_desc *desc, bool value) { @@ -1300,17 +1311,16 @@ static void gpio_chip_set_multiple(struct gpio_chip *chip, continue; } /* set outputs if the corresponding mask bit is set */ - if (__test_and_clear_bit(i, mask)) { + if (__test_and_clear_bit(i, mask)) chip->set(chip, i, test_bit(i, bits)); - } } } } -static void gpiod_set_array_priv(bool raw, bool can_sleep, - unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) +static void gpiod_set_array_value_priv(bool raw, bool can_sleep, + unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) { int i = 0; @@ -1320,9 +1330,9 @@ static void gpiod_set_array_priv(bool raw, bool can_sleep, unsigned long bits[BITS_TO_LONGS(chip->ngpio)]; int count = 0; - if (!can_sleep) { + if (!can_sleep) WARN_ON(chip->can_sleep); - } + memset(mask, 0, sizeof(mask)); do { struct gpio_desc *desc = desc_array[i]; @@ -1337,24 +1347,22 @@ static void gpiod_set_array_priv(bool raw, bool can_sleep, * open drain and open source outputs are set individually */ if (test_bit(FLAG_OPEN_DRAIN, &desc->flags)) { - _gpio_set_open_drain_value(desc,value); + _gpio_set_open_drain_value(desc, value); } else if (test_bit(FLAG_OPEN_SOURCE, &desc->flags)) { _gpio_set_open_source_value(desc, value); } else { __set_bit(hwgpio, mask); - if (value) { + if (value) __set_bit(hwgpio, bits); - } else { + else __clear_bit(hwgpio, bits); - } count++; } i++; } while ((i < array_size) && (desc_array[i]->chip == chip)); /* push collected bits to outputs */ - if (count != 0) { + if (count != 0) gpio_chip_set_multiple(chip, mask, bits); - } } } @@ -1403,7 +1411,7 @@ void gpiod_set_value(struct gpio_desc *desc, int value) EXPORT_SYMBOL_GPL(gpiod_set_value); /** - * gpiod_set_raw_array() - assign values to an array of GPIOs + * gpiod_set_raw_array_value() - assign values to an array of GPIOs * @array_size: number of elements in the descriptor / value arrays * @desc_array: array of GPIO descriptors whose values will be assigned * @value_array: array of values to assign @@ -1414,17 +1422,18 @@ EXPORT_SYMBOL_GPL(gpiod_set_value); * This function should be called from contexts where we cannot sleep, and will * complain if the GPIO chip functions potentially sleep. */ -void gpiod_set_raw_array(unsigned int array_size, +void gpiod_set_raw_array_value(unsigned int array_size, struct gpio_desc **desc_array, int *value_array) { if (!desc_array) return; - gpiod_set_array_priv(true, false, array_size, desc_array, value_array); + gpiod_set_array_value_priv(true, false, array_size, desc_array, + value_array); } -EXPORT_SYMBOL_GPL(gpiod_set_raw_array); +EXPORT_SYMBOL_GPL(gpiod_set_raw_array_value); /** - * gpiod_set_array() - assign values to an array of GPIOs + * gpiod_set_array_value() - assign values to an array of GPIOs * @array_size: number of elements in the descriptor / value arrays * @desc_array: array of GPIO descriptors whose values will be assigned * @value_array: array of values to assign @@ -1435,14 +1444,15 @@ EXPORT_SYMBOL_GPL(gpiod_set_raw_array); * This function should be called from contexts where we cannot sleep, and will * complain if the GPIO chip functions potentially sleep. */ -void gpiod_set_array(unsigned int array_size, - struct gpio_desc **desc_array, int *value_array) +void gpiod_set_array_value(unsigned int array_size, + struct gpio_desc **desc_array, int *value_array) { if (!desc_array) return; - gpiod_set_array_priv(false, false, array_size, desc_array, value_array); + gpiod_set_array_value_priv(false, false, array_size, desc_array, + value_array); } -EXPORT_SYMBOL_GPL(gpiod_set_array); +EXPORT_SYMBOL_GPL(gpiod_set_array_value); /** * gpiod_cansleep() - report whether gpio value access may sleep @@ -1604,7 +1614,7 @@ void gpiod_set_value_cansleep(struct gpio_desc *desc, int value) EXPORT_SYMBOL_GPL(gpiod_set_value_cansleep); /** - * gpiod_set_raw_array_cansleep() - assign values to an array of GPIOs + * gpiod_set_raw_array_value_cansleep() - assign values to an array of GPIOs * @array_size: number of elements in the descriptor / value arrays * @desc_array: array of GPIO descriptors whose values will be assigned * @value_array: array of values to assign @@ -1614,19 +1624,20 @@ EXPORT_SYMBOL_GPL(gpiod_set_value_cansleep); * * This function is to be called from contexts that can sleep. */ -void gpiod_set_raw_array_cansleep(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) +void gpiod_set_raw_array_value_cansleep(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) { might_sleep_if(extra_checks); if (!desc_array) return; - gpiod_set_array_priv(true, true, array_size, desc_array, value_array); + gpiod_set_array_value_priv(true, true, array_size, desc_array, + value_array); } -EXPORT_SYMBOL_GPL(gpiod_set_raw_array_cansleep); +EXPORT_SYMBOL_GPL(gpiod_set_raw_array_value_cansleep); /** - * gpiod_set_array_cansleep() - assign values to an array of GPIOs + * gpiod_set_array_value_cansleep() - assign values to an array of GPIOs * @array_size: number of elements in the descriptor / value arrays * @desc_array: array of GPIO descriptors whose values will be assigned * @value_array: array of values to assign @@ -1636,16 +1647,17 @@ EXPORT_SYMBOL_GPL(gpiod_set_raw_array_cansleep); * * This function is to be called from contexts that can sleep. */ -void gpiod_set_array_cansleep(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) +void gpiod_set_array_value_cansleep(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) { might_sleep_if(extra_checks); if (!desc_array) return; - gpiod_set_array_priv(false, true, array_size, desc_array, value_array); + gpiod_set_array_value_priv(false, true, array_size, desc_array, + value_array); } -EXPORT_SYMBOL_GPL(gpiod_set_array_cansleep); +EXPORT_SYMBOL_GPL(gpiod_set_array_value_cansleep); /** * gpiod_add_lookup_table() - register GPIO device consumers @@ -1880,7 +1892,7 @@ EXPORT_SYMBOL_GPL(gpiod_count); * * Return the GPIO descriptor corresponding to the function con_id of device * dev, -ENOENT if no GPIO has been assigned to the requested function, or - * another IS_ERR() code if an error occured while trying to acquire the GPIO. + * another IS_ERR() code if an error occurred while trying to acquire the GPIO. */ struct gpio_desc *__must_check __gpiod_get(struct device *dev, const char *con_id, enum gpiod_flags flags) @@ -1960,7 +1972,7 @@ static int gpiod_configure_flags(struct gpio_desc *desc, const char *con_id, * * Return a valid GPIO descriptor, -ENOENT if no GPIO has been assigned to the * requested function and/or index, or another IS_ERR() code if an error - * occured while trying to acquire the GPIO. + * occurred while trying to acquire the GPIO. */ struct gpio_desc *__must_check __gpiod_get_index(struct device *dev, const char *con_id, @@ -2118,13 +2130,15 @@ int gpiod_hog(struct gpio_desc *desc, const char *name, local_desc = gpiochip_request_own_desc(chip, hwnum, name); if (IS_ERR(local_desc)) { - pr_debug("requesting own GPIO %s failed\n", name); + pr_err("requesting hog GPIO %s (chip %s, offset %d) failed\n", + name, chip->label, hwnum); return PTR_ERR(local_desc); } status = gpiod_configure_flags(desc, name, lflags, dflags); if (status < 0) { - pr_debug("setup of GPIO %s failed\n", name); + pr_err("setup of hog GPIO %s (chip %s, offset %d) failed\n", + name, chip->label, hwnum); gpiochip_free_own_desc(desc); return status; } diff --git a/drivers/gpio/gpiolib.h b/drivers/gpio/gpiolib.h index 594b1798c0e7..bf343004b008 100644 --- a/drivers/gpio/gpiolib.h +++ b/drivers/gpio/gpiolib.h @@ -83,20 +83,12 @@ struct gpio_desc { #define FLAG_IS_OUT 1 #define FLAG_EXPORT 2 /* protected by sysfs_lock */ #define FLAG_SYSFS 3 /* exported via /sys/class/gpio/control */ -#define FLAG_TRIG_FALL 4 /* trigger on falling edge */ -#define FLAG_TRIG_RISE 5 /* trigger on rising edge */ #define FLAG_ACTIVE_LOW 6 /* value has active low */ #define FLAG_OPEN_DRAIN 7 /* Gpio is open drain type */ #define FLAG_OPEN_SOURCE 8 /* Gpio is open source type */ #define FLAG_USED_AS_IRQ 9 /* GPIO is connected to an IRQ */ -#define FLAG_SYSFS_DIR 10 /* show sysfs direction attribute */ #define FLAG_IS_HOGGED 11 /* GPIO is hogged */ -#define ID_SHIFT 16 /* add new flags before this one */ - -#define GPIO_FLAGS_MASK ((1 << ID_SHIFT) - 1) -#define GPIO_TRIGGER_MASK (BIT(FLAG_TRIG_FALL) | BIT(FLAG_TRIG_RISE)) - const char *label; }; @@ -151,17 +143,17 @@ static int __maybe_unused gpio_chip_hwgpio(const struct gpio_desc *desc) #ifdef CONFIG_GPIO_SYSFS -int gpiochip_export(struct gpio_chip *chip); -void gpiochip_unexport(struct gpio_chip *chip); +int gpiochip_sysfs_register(struct gpio_chip *chip); +void gpiochip_sysfs_unregister(struct gpio_chip *chip); #else -static inline int gpiochip_export(struct gpio_chip *chip) +static inline int gpiochip_sysfs_register(struct gpio_chip *chip) { return 0; } -static inline void gpiochip_unexport(struct gpio_chip *chip) +static inline void gpiochip_sysfs_unregister(struct gpio_chip *chip) { } diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 987c124432c5..fc2ee8213fb6 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -107,7 +107,7 @@ static int acpi_i2c_add_resource(struct acpi_resource *ares, void *data) if (sb->access_mode == ACPI_I2C_10BIT_MODE) info->flags |= I2C_CLIENT_TEN; } - } else if (info->irq < 0) { + } else if (!info->irq) { struct resource r; if (acpi_dev_resource_interrupt(ares, 0, &r)) @@ -134,7 +134,6 @@ static acpi_status acpi_i2c_add_device(acpi_handle handle, u32 level, memset(&info, 0, sizeof(info)); info.fwnode = acpi_fwnode_handle(adev); - info.irq = -1; INIT_LIST_HEAD(&resource_list); ret = acpi_dev_get_resources(adev, &resource_list, @@ -632,8 +631,13 @@ static int i2c_device_probe(struct device *dev) if (!client) return 0; - if (!client->irq && dev->of_node) { - int irq = of_irq_get(dev->of_node, 0); + if (!client->irq) { + int irq = -ENOENT; + + if (dev->of_node) + irq = of_irq_get(dev->of_node, 0); + else if (ACPI_COMPANION(dev)) + irq = acpi_dev_gpio_irq_get(ACPI_COMPANION(dev), 0); if (irq == -EPROBE_DEFER) return irq; diff --git a/drivers/net/phy/mdio-mux-gpio.c b/drivers/net/phy/mdio-mux-gpio.c index 66edd99bc302..7ddb1ab70891 100644 --- a/drivers/net/phy/mdio-mux-gpio.c +++ b/drivers/net/phy/mdio-mux-gpio.c @@ -35,7 +35,8 @@ static int mdio_mux_gpio_switch_fn(int current_child, int desired_child, for (n = 0; n < s->gpios->ndescs; n++) values[n] = (desired_child >> n) & 1; - gpiod_set_array_cansleep(s->gpios->ndescs, s->gpios->desc, values); + gpiod_set_array_value_cansleep(s->gpios->ndescs, s->gpios->desc, + values); return 0; } diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c index 0ec756c62bcf..d7b846d41630 100644 --- a/drivers/tty/serial/serial_mctrl_gpio.c +++ b/drivers/tty/serial/serial_mctrl_gpio.c @@ -55,7 +55,7 @@ void mctrl_gpio_set(struct mctrl_gpios *gpios, unsigned int mctrl) value_array[count] = !!(mctrl & mctrl_gpios_desc[i].mctrl); count++; } - gpiod_set_array(count, desc_array, value_array); + gpiod_set_array_value(count, desc_array, value_array); } EXPORT_SYMBOL_GPL(mctrl_gpio_set); diff --git a/include/asm-generic/gpio.h b/include/asm-generic/gpio.h index 9bb0d11729c9..40ec1433f05d 100644 --- a/include/asm-generic/gpio.h +++ b/include/asm-generic/gpio.h @@ -128,11 +128,6 @@ static inline int gpio_export_link(struct device *dev, const char *name, return gpiod_export_link(dev, name, gpio_to_desc(gpio)); } -static inline int gpio_sysfs_set_active_low(unsigned gpio, int value) -{ - return gpiod_sysfs_set_active_low(gpio_to_desc(gpio), value); -} - static inline void gpio_unexport(unsigned gpio) { gpiod_unexport(gpio_to_desc(gpio)); diff --git a/include/linux/acpi.h b/include/linux/acpi.h index e4da5e35e29c..f57c440642cd 100644 --- a/include/linux/acpi.h +++ b/include/linux/acpi.h @@ -721,6 +721,8 @@ static inline void acpi_dev_remove_driver_gpios(struct acpi_device *adev) if (adev) adev->driver_gpios = NULL; } + +int acpi_dev_gpio_irq_get(struct acpi_device *adev, int index); #else static inline int acpi_dev_add_driver_gpios(struct acpi_device *adev, const struct acpi_gpio_mapping *gpios) @@ -728,6 +730,11 @@ static inline int acpi_dev_add_driver_gpios(struct acpi_device *adev, return -ENXIO; } static inline void acpi_dev_remove_driver_gpios(struct acpi_device *adev) {} + +static inline int acpi_dev_gpio_irq_get(struct acpi_device *adev, int index) +{ + return -ENXIO; +} #endif /* Device properties */ diff --git a/include/linux/basic_mmio_gpio.h b/include/linux/basic_mmio_gpio.h index 0e97856b2cff..14eea946e640 100644 --- a/include/linux/basic_mmio_gpio.h +++ b/include/linux/basic_mmio_gpio.h @@ -74,5 +74,6 @@ int bgpio_init(struct bgpio_chip *bgc, struct device *dev, #define BGPIOF_UNREADABLE_REG_SET BIT(1) /* reg_set is unreadable */ #define BGPIOF_UNREADABLE_REG_DIR BIT(2) /* reg_dir is unreadable */ #define BGPIOF_BIG_ENDIAN_BYTE_ORDER BIT(3) +#define BGPIOF_READ_OUTPUT_REG_SET BIT(4) /* reg_set stores output value */ #endif /* __BASIC_MMIO_GPIO_H */ diff --git a/include/linux/gpio.h b/include/linux/gpio.h index ab81339a8590..d12b5d566e4b 100644 --- a/include/linux/gpio.h +++ b/include/linux/gpio.h @@ -196,13 +196,6 @@ static inline int gpio_export_link(struct device *dev, const char *name, return -EINVAL; } -static inline int gpio_sysfs_set_active_low(unsigned gpio, int value) -{ - /* GPIO can never have been requested */ - WARN_ON(1); - return -EINVAL; -} - static inline void gpio_unexport(unsigned gpio) { /* GPIO can never have been exported */ diff --git a/include/linux/gpio/consumer.h b/include/linux/gpio/consumer.h index 3a7c9ffd5ab9..fd098169fe87 100644 --- a/include/linux/gpio/consumer.h +++ b/include/linux/gpio/consumer.h @@ -100,24 +100,25 @@ int gpiod_direction_output_raw(struct gpio_desc *desc, int value); /* Value get/set from non-sleeping context */ int gpiod_get_value(const struct gpio_desc *desc); void gpiod_set_value(struct gpio_desc *desc, int value); -void gpiod_set_array(unsigned int array_size, - struct gpio_desc **desc_array, int *value_array); +void gpiod_set_array_value(unsigned int array_size, + struct gpio_desc **desc_array, int *value_array); int gpiod_get_raw_value(const struct gpio_desc *desc); void gpiod_set_raw_value(struct gpio_desc *desc, int value); -void gpiod_set_raw_array(unsigned int array_size, - struct gpio_desc **desc_array, int *value_array); +void gpiod_set_raw_array_value(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array); /* Value get/set from sleeping context */ int gpiod_get_value_cansleep(const struct gpio_desc *desc); void gpiod_set_value_cansleep(struct gpio_desc *desc, int value); -void gpiod_set_array_cansleep(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array); +void gpiod_set_array_value_cansleep(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array); int gpiod_get_raw_value_cansleep(const struct gpio_desc *desc); void gpiod_set_raw_value_cansleep(struct gpio_desc *desc, int value); -void gpiod_set_raw_array_cansleep(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array); +void gpiod_set_raw_array_value_cansleep(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array); int gpiod_set_debounce(struct gpio_desc *desc, unsigned debounce); @@ -304,9 +305,9 @@ static inline void gpiod_set_value(struct gpio_desc *desc, int value) /* GPIO can never have been requested */ WARN_ON(1); } -static inline void gpiod_set_array(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) +static inline void gpiod_set_array_value(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) { /* GPIO can never have been requested */ WARN_ON(1); @@ -322,9 +323,9 @@ static inline void gpiod_set_raw_value(struct gpio_desc *desc, int value) /* GPIO can never have been requested */ WARN_ON(1); } -static inline void gpiod_set_raw_array(unsigned int array_size, - struct gpio_desc **desc_array, - int *value_array) +static inline void gpiod_set_raw_array_value(unsigned int array_size, + struct gpio_desc **desc_array, + int *value_array) { /* GPIO can never have been requested */ WARN_ON(1); @@ -341,7 +342,7 @@ static inline void gpiod_set_value_cansleep(struct gpio_desc *desc, int value) /* GPIO can never have been requested */ WARN_ON(1); } -static inline void gpiod_set_array_cansleep(unsigned int array_size, +static inline void gpiod_set_array_value_cansleep(unsigned int array_size, struct gpio_desc **desc_array, int *value_array) { @@ -360,7 +361,7 @@ static inline void gpiod_set_raw_value_cansleep(struct gpio_desc *desc, /* GPIO can never have been requested */ WARN_ON(1); } -static inline void gpiod_set_raw_array_cansleep(unsigned int array_size, +static inline void gpiod_set_raw_array_value_cansleep(unsigned int array_size, struct gpio_desc **desc_array, int *value_array) { @@ -449,7 +450,6 @@ static inline int desc_to_gpio(const struct gpio_desc *desc) int gpiod_export(struct gpio_desc *desc, bool direction_may_change); int gpiod_export_link(struct device *dev, const char *name, struct gpio_desc *desc); -int gpiod_sysfs_set_active_low(struct gpio_desc *desc, int value); void gpiod_unexport(struct gpio_desc *desc); #else /* CONFIG_GPIOLIB && CONFIG_GPIO_SYSFS */ @@ -466,11 +466,6 @@ static inline int gpiod_export_link(struct device *dev, const char *name, return -ENOSYS; } -static inline int gpiod_sysfs_set_active_low(struct gpio_desc *desc, int value) -{ - return -ENOSYS; -} - static inline void gpiod_unexport(struct gpio_desc *desc) { } diff --git a/include/linux/gpio/driver.h b/include/linux/gpio/driver.h index f1b36593ec9f..cc7ec129b329 100644 --- a/include/linux/gpio/driver.h +++ b/include/linux/gpio/driver.h @@ -20,6 +20,7 @@ struct seq_file; * struct gpio_chip - abstract a GPIO controller * @label: for diagnostics * @dev: optional device providing the GPIOs + * @cdev: class device used by sysfs interface (may be NULL) * @owner: helps prevent removal of modules exporting active GPIOs * @list: links gpio_chips together for traversal * @request: optional hook for chip-specific activation, such as @@ -41,8 +42,12 @@ struct seq_file; * @dbg_show: optional routine to show contents in debugfs; default code * will be used when this is omitted, but custom code can show extra * state (such as pullup/pulldown configuration). - * @base: identifies the first GPIO number handled by this chip; or, if - * negative during registration, requests dynamic ID allocation. + * @base: identifies the first GPIO number handled by this chip; + * or, if negative during registration, requests dynamic ID allocation. + * DEPRECATION: providing anything non-negative and nailing the base + * base offset of GPIO chips is deprecated. Please pass -1 as base to + * let gpiolib select the chip base in all possible cases. We want to + * get rid of the static GPIO number space in the long run. * @ngpio: the number of GPIOs handled by this controller; the last GPIO * handled is (base + ngpio - 1). * @desc: array of ngpio descriptors. Private. @@ -57,7 +62,6 @@ struct seq_file; * implies that if the chip supports IRQs, these IRQs need to be threaded * as the chip access may sleep when e.g. reading out the IRQ status * registers. - * @exported: flags if the gpiochip is exported for use from sysfs. Private. * @irq_not_threaded: flag must be set if @can_sleep is set but the * IRQs don't need to be threaded * @@ -74,6 +78,7 @@ struct seq_file; struct gpio_chip { const char *label; struct device *dev; + struct device *cdev; struct module *owner; struct list_head list; @@ -109,7 +114,6 @@ struct gpio_chip { const char *const *names; bool can_sleep; bool irq_not_threaded; - bool exported; #ifdef CONFIG_GPIOLIB_IRQCHIP /* @@ -121,6 +125,7 @@ struct gpio_chip { unsigned int irq_base; irq_flow_handler_t irq_handler; unsigned int irq_default_type; + int irq_parent; #endif #if defined(CONFIG_OF_GPIO) diff --git a/include/linux/platform_data/gpio-omap.h b/include/linux/platform_data/gpio-omap.h index 5d50b25a73d7..cb2618147c34 100644 --- a/include/linux/platform_data/gpio-omap.h +++ b/include/linux/platform_data/gpio-omap.h @@ -208,9 +208,17 @@ struct omap_gpio_platform_data { int (*get_context_loss_count)(struct device *dev); }; +#if IS_BUILTIN(CONFIG_GPIO_OMAP) extern void omap2_gpio_prepare_for_idle(int off_mode); extern void omap2_gpio_resume_after_idle(void); -extern void omap_set_gpio_debounce(int gpio, int enable); -extern void omap_set_gpio_debounce_time(int gpio, int enable); +#else +static inline void omap2_gpio_prepare_for_idle(int off_mode) +{ +} + +static inline void omap2_gpio_resume_after_idle(void) +{ +} +#endif #endif