stmmac: extend CSR Clock Range programming

The CSR Clock Range has been reworked and new macros has
been added in the platform header to allow the CSR Clock
Range selection in the GMII Address Register.
The previous work didn't add the other fields
that can be used to achieve MDC clock of frequency
higher than the IEEE 802.3 specified frequency limit
of 2.5 MHz and program a clock divider of lower value.
On such platforms, these are used indeed so this patch
adds them.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
Giuseppe CAVALLARO 2012-04-04 04:33:26 +00:00 committed by David S. Miller
parent ba1377ffe9
commit 18f05d64ec
2 changed files with 18 additions and 17 deletions

View File

@ -70,7 +70,7 @@ static int stmmac_mdio_read(struct mii_bus *bus, int phyaddr, int phyreg)
int data;
u16 regValue = (((phyaddr << 11) & (0x0000F800)) |
((phyreg << 6) & (0x000007C0)));
regValue |= MII_BUSY | ((priv->plat->clk_csr & 7) << 2);
regValue |= MII_BUSY | ((priv->plat->clk_csr & 0xF) << 2);
if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address))
return -EBUSY;
@ -106,7 +106,7 @@ static int stmmac_mdio_write(struct mii_bus *bus, int phyaddr, int phyreg,
(((phyaddr << 11) & (0x0000F800)) | ((phyreg << 6) & (0x000007C0)))
| MII_WRITE;
value |= MII_BUSY | ((priv->plat->clk_csr & 7) << 2);
value |= MII_BUSY | ((priv->plat->clk_csr & 0xF) << 2);
/* Wait until any existing MII operation is complete */
if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address))

View File

@ -37,28 +37,29 @@
* This could also be configured at run time using CPU freq framework. */
/* MDC Clock Selection define*/
#define STMMAC_CSR_60_100M 0 /* MDC = clk_scr_i/42 */
#define STMMAC_CSR_100_150M 1 /* MDC = clk_scr_i/62 */
#define STMMAC_CSR_20_35M 2 /* MDC = clk_scr_i/16 */
#define STMMAC_CSR_35_60M 3 /* MDC = clk_scr_i/26 */
#define STMMAC_CSR_150_250M 4 /* MDC = clk_scr_i/102 */
#define STMMAC_CSR_250_300M 5 /* MDC = clk_scr_i/122 */
#define STMMAC_CSR_60_100M 0x0 /* MDC = clk_scr_i/42 */
#define STMMAC_CSR_100_150M 0x1 /* MDC = clk_scr_i/62 */
#define STMMAC_CSR_20_35M 0x2 /* MDC = clk_scr_i/16 */
#define STMMAC_CSR_35_60M 0x3 /* MDC = clk_scr_i/26 */
#define STMMAC_CSR_150_250M 0x4 /* MDC = clk_scr_i/102 */
#define STMMAC_CSR_250_300M 0x5 /* MDC = clk_scr_i/122 */
/* FIXME: The MDC clock could be set higher than the IEEE 802.3
/* The MDC clock could be set higher than the IEEE 802.3
* specified frequency limit 0f 2.5 MHz, by programming a clock divider
* of value different than the above defined values. The resultant MDIO
* clock frequency of 12.5 MHz is applicable for the interfacing chips
* supporting higher MDC clocks.
* The MDC clock selection macros need to be defined for MDC clock rate
* of 12.5 MHz, corresponding to the following selection.
* 1000 clk_csr_i/4
* 1001 clk_csr_i/6
* 1010 clk_csr_i/8
* 1011 clk_csr_i/10
* 1100 clk_csr_i/12
* 1101 clk_csr_i/14
* 1110 clk_csr_i/16
* 1111 clk_csr_i/18 */
*/
#define STMMAC_CSR_I_4 0x8 /* clk_csr_i/4 */
#define STMMAC_CSR_I_6 0x9 /* clk_csr_i/6 */
#define STMMAC_CSR_I_8 0xA /* clk_csr_i/8 */
#define STMMAC_CSR_I_10 0xB /* clk_csr_i/10 */
#define STMMAC_CSR_I_12 0xC /* clk_csr_i/12 */
#define STMMAC_CSR_I_14 0xD /* clk_csr_i/14 */
#define STMMAC_CSR_I_16 0xE /* clk_csr_i/16 */
#define STMMAC_CSR_I_18 0xF /* clk_csr_i/18 */
/* AXI DMA Burst length suported */
#define DMA_AXI_BLEN_4 (1 << 1)