[PATCH] powerpc: Migrate Xilinx Vertex support from the OCP bus to the platfom bus.

This patch only deals with the serial port definitions as there is no
support for any other xilinx IP cores in the kernel tree at the moment.

Board specific configuration moved out of virtex.[ch] and into the
xparameters.h wrapper.

This also prepares for the transition to the flattened device tree model.
When the bootloader provides a device tree generated from an xparameters.h
files, the kernel will no longer need xparameters/*.  The platform bus will
get populated with data from the device tree, and the device drivers will
be automatically connected to the devices.  Only the bootloader (or
ppcboot) will need xparameters directly.

Signed-off-by: Grant C. Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This commit is contained in:
Grant C. Likely 2006-01-19 01:12:48 -07:00 committed by Paul Mackerras
parent 562e7370a4
commit 1a42e53d17
7 changed files with 85 additions and 133 deletions

View File

@ -8,6 +8,9 @@
#include <linux/serial_reg.h> #include <linux/serial_reg.h>
#include <asm/serial.h> #include <asm/serial.h>
#if defined(CONFIG_XILINX_VIRTEX)
#include <platforms/4xx/xparameters/xparameters.h>
#endif
#include "nonstdio.h" #include "nonstdio.h"
#include "serial.h" #include "serial.h"

View File

@ -21,6 +21,9 @@
#ifdef CONFIG_40x #ifdef CONFIG_40x
#include <asm/io.h> #include <asm/io.h>
#endif #endif
#ifdef CONFIG_XILINX_VIRTEX
#include <platforms/4xx/xparameters/xparameters.h>
#endif
extern unsigned long timebase_period_ns; extern unsigned long timebase_period_ns;
/* For those boards that don't provide one. /* For those boards that don't provide one.

View File

@ -172,11 +172,6 @@ config IBM_OCP
depends on ASH || BAMBOO || BUBINGA || CPCI405 || EBONY || EP405 || LUAN || YUCCA || OCOTEA || REDWOOD_5 || REDWOOD_6 || SYCAMORE || WALNUT depends on ASH || BAMBOO || BUBINGA || CPCI405 || EBONY || EP405 || LUAN || YUCCA || OCOTEA || REDWOOD_5 || REDWOOD_6 || SYCAMORE || WALNUT
default y default y
config XILINX_OCP
bool
depends on XILINX_ML300
default y
config IBM_EMAC4 config IBM_EMAC4
bool bool
depends on 440GX || 440SP || 440SPE depends on 440GX || 440SP || 440SPE

View File

@ -1,60 +1,56 @@
/* /*
* arch/ppc/platforms/4xx/virtex.c * Virtex-II Pro & Virtex-4 FX common infrastructure
* *
* Author: MontaVista Software, Inc. * Maintainer: Grant Likely <grant.likely@secretlab.ca>
* source@mvista.com
* *
* 2002-2004 (c) MontaVista Software, Inc. This file is licensed under the * Copyright 2005 Secret Lab Technologies Ltd.
* terms of the GNU General Public License version 2. This program is licensed * Copyright 2005 General Dynamics Canada Ltd.
* "as is" without any warranty of any kind, whether express or implied. * Copyright 2005 Freescale Semiconductor Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/ */
#include <linux/config.h>
#include <linux/init.h> #include <linux/init.h>
#include <asm/ocp.h> #include <linux/module.h>
#include <linux/device.h>
#include <linux/serial_8250.h>
#include <asm/ppc_sys.h>
#include <platforms/4xx/virtex.h> #include <platforms/4xx/virtex.h>
#include <platforms/4xx/xparameters/xparameters.h>
/* Have OCP take care of the serial ports. */ #define XPAR_UART(num) { \
struct ocp_def core_ocp[] = { .mapbase = XPAR_UARTNS550_##num##_BASEADDR + 3, \
#ifdef XPAR_UARTNS550_0_BASEADDR .irq = XPAR_INTC_0_UARTNS550_##num##_VEC_ID, \
{ .vendor = OCP_VENDOR_XILINX, .iotype = UPIO_MEM, \
.function = OCP_FUNC_16550, .uartclk = XPAR_UARTNS550_##num##_CLOCK_FREQ_HZ, \
.index = 0, .flags = UPF_BOOT_AUTOCONF, \
.paddr = XPAR_UARTNS550_0_BASEADDR, .regshift = 2, \
.irq = XPAR_INTC_0_UARTNS550_0_VEC_ID,
.pm = OCP_CPM_NA
},
#ifdef XPAR_UARTNS550_1_BASEADDR
{ .vendor = OCP_VENDOR_XILINX,
.function = OCP_FUNC_16550,
.index = 1,
.paddr = XPAR_UARTNS550_1_BASEADDR,
.irq = XPAR_INTC_0_UARTNS550_1_VEC_ID,
.pm = OCP_CPM_NA
},
#ifdef XPAR_UARTNS550_2_BASEADDR
{ .vendor = OCP_VENDOR_XILINX,
.function = OCP_FUNC_16550,
.index = 2,
.paddr = XPAR_UARTNS550_2_BASEADDR,
.irq = XPAR_INTC_0_UARTNS550_2_VEC_ID,
.pm = OCP_CPM_NA
},
#ifdef XPAR_UARTNS550_3_BASEADDR
{ .vendor = OCP_VENDOR_XILINX,
.function = OCP_FUNC_16550,
.index = 3,
.paddr = XPAR_UARTNS550_3_BASEADDR,
.irq = XPAR_INTC_0_UARTNS550_3_VEC_ID,
.pm = OCP_CPM_NA
},
#ifdef XPAR_UARTNS550_4_BASEADDR
#error Edit this file to add more devices.
#endif /* 4 */
#endif /* 3 */
#endif /* 2 */
#endif /* 1 */
#endif /* 0 */
{ .vendor = OCP_VENDOR_INVALID
} }
struct plat_serial8250_port serial_platform_data[] = {
#ifdef XPAR_UARTNS550_0_BASEADDR
XPAR_UART(0),
#endif
#ifdef XPAR_UARTNS550_1_BASEADDR
XPAR_UART(1),
#endif
#ifdef XPAR_UARTNS550_2_BASEADDR
XPAR_UART(2),
#endif
#ifdef XPAR_UARTNS550_3_BASEADDR
XPAR_UART(3),
#endif
{ }, /* terminated by empty record */
}; };
struct platform_device ppc_sys_platform_devices[] = {
[VIRTEX_UART] = {
.name = "serial8250",
.id = 0,
.dev.platform_data = serial_platform_data,
},
};

View File

@ -15,85 +15,21 @@
#ifndef __ASM_VIRTEX_H__ #ifndef __ASM_VIRTEX_H__
#define __ASM_VIRTEX_H__ #define __ASM_VIRTEX_H__
#include <linux/config.h>
#include <platforms/4xx/xparameters/xparameters.h>
/* serial defines */ /* serial defines */
#define RS_TABLE_SIZE 4 /* change this and add more devices below
if you have more then 4 16x50 UARTs */
#define BASE_BAUD (XPAR_UARTNS550_0_CLOCK_FREQ_HZ/16)
/* The serial ports in the Virtex-II Pro have each I/O byte in the
* LSByte of a word. This means that iomem_reg_shift needs to be 2 to
* change the byte offsets into word offsets. In addition the base
* addresses need to have 3 added to them to get to the LSByte.
*/
#define STD_UART_OP(num) \
{ 0, BASE_BAUD, 0, XPAR_INTC_0_UARTNS550_##num##_VEC_ID, \
ASYNC_BOOT_AUTOCONF, \
.iomem_base = (u8 *)XPAR_UARTNS550_##num##_BASEADDR + 3, \
.iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM},
#if defined(XPAR_INTC_0_UARTNS550_0_VEC_ID)
#define ML300_UART0 STD_UART_OP(0)
#else
#define ML300_UART0
#endif
#if defined(XPAR_INTC_0_UARTNS550_1_VEC_ID)
#define ML300_UART1 STD_UART_OP(1)
#else
#define ML300_UART1
#endif
#if defined(XPAR_INTC_0_UARTNS550_2_VEC_ID)
#define ML300_UART2 STD_UART_OP(2)
#else
#define ML300_UART2
#endif
#if defined(XPAR_INTC_0_UARTNS550_3_VEC_ID)
#define ML300_UART3 STD_UART_OP(3)
#else
#define ML300_UART3
#endif
#if defined(XPAR_INTC_0_UARTNS550_4_VEC_ID)
#error Edit this file to add more devices.
#elif defined(XPAR_INTC_0_UARTNS550_3_VEC_ID)
#define NR_SER_PORTS 4
#elif defined(XPAR_INTC_0_UARTNS550_2_VEC_ID)
#define NR_SER_PORTS 3
#elif defined(XPAR_INTC_0_UARTNS550_1_VEC_ID)
#define NR_SER_PORTS 2
#elif defined(XPAR_INTC_0_UARTNS550_0_VEC_ID)
#define NR_SER_PORTS 1
#else
#define NR_SER_PORTS 0
#endif
#if defined(CONFIG_UART0_TTYS0)
#define SERIAL_PORT_DFNS \
ML300_UART0 \
ML300_UART1 \
ML300_UART2 \
ML300_UART3
#endif
#if defined(CONFIG_UART0_TTYS1)
#define SERIAL_PORT_DFNS \
ML300_UART1 \
ML300_UART0 \
ML300_UART2 \
ML300_UART3
#endif
#define DCRN_CPMFR_BASE 0
#include <asm/ibm405.h> #include <asm/ibm405.h>
/* Ugly, ugly, ugly! BASE_BAUD defined here to keep 8250.c happy. */
#if !defined(BASE_BAUD)
#define BASE_BAUD (0) /* dummy value; not used */
#endif
/* Device type enumeration for platform bus definitions */
#ifndef __ASSEMBLY__
enum ppc_sys_devices {
VIRTEX_UART,
};
#endif
#endif /* __ASM_VIRTEX_H__ */ #endif /* __ASM_VIRTEX_H__ */
#endif /* __KERNEL__ */ #endif /* __KERNEL__ */

View File

@ -1,7 +1,8 @@
/* /*
* include/asm-ppc/xparameters.h * include/asm-ppc/xparameters.h
* *
* This file includes the correct xparameters.h for the CONFIG'ed board * This file includes the correct xparameters.h for the CONFIG'ed board plus
* fixups to translate board specific XPAR values to a common set of names
* *
* Author: MontaVista Software, Inc. * Author: MontaVista Software, Inc.
* source@mvista.com * source@mvista.com
@ -14,5 +15,21 @@
#include <linux/config.h> #include <linux/config.h>
#if defined(CONFIG_XILINX_ML300) #if defined(CONFIG_XILINX_ML300)
#include <platforms/4xx/xparameters/xparameters_ml300.h> #include "xparameters_ml300.h"
#else
/* Add other board xparameter includes here before the #else */
#error No xparameters_*.h file included
#endif
#ifndef SERIAL_PORT_DFNS
/* zImage serial port definitions */
#define RS_TABLE_SIZE 1
#define SERIAL_PORT_DFNS { \
.baud_base = XPAR_UARTNS550_0_CLOCK_FREQ_HZ/16, \
.irq = XPAR_INTC_0_UARTNS550_0_VEC_ID, \
.flags = ASYNC_BOOT_AUTOCONF, \
.iomem_base = (u8 *)XPAR_UARTNS550_0_BASEADDR + 3, \
.iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM, \
},
#endif #endif

View File

@ -33,6 +33,8 @@
#include <asm/mpc52xx.h> #include <asm/mpc52xx.h>
#elif defined(CONFIG_MPC10X_BRIDGE) #elif defined(CONFIG_MPC10X_BRIDGE)
#include <asm/mpc10x.h> #include <asm/mpc10x.h>
#elif defined(CONFIG_XILINX_VIRTEX)
#include <platforms/4xx/virtex.h>
#else #else
#error "need definition of ppc_sys_devices" #error "need definition of ppc_sys_devices"
#endif #endif