ARM: dts: imx6sx-sdb: Fix enet phy regulator

Bindings for "fixed-regulator" only explicitly support "gpio" property,
not "gpios". Fix by correcting the property name.

The enet PHYs on imx6sx-sdb needs to be explicitly reset after a power
cycle, this can be handled by the phy-reset-gpios property. Sadly this
is not handled on suspend: the fec driver turns phy-supply off but
doesn't assert phy-reset-gpios again on resume.

Since additional phy-level work is required to support powering off the
phy in suspend fix the problem by just marking the regulator as
"boot-on" "always-on" so that it's never turned off. This behavior is
equivalent to older releases.

Keep the phy-reset-gpios property on fec anyway because it is a correct
description of board design.

This issue was exposed by commit efdfeb079c ("regulator: fixed:
Convert to use GPIO descriptor only") which causes the "gpios" property
to also be parsed. Before that commit the "gpios" property had no
effect, PHY reset was only handled in the the bootloader.

This fixes linux-next boot failures previously reported here:
 https://lore.kernel.org/patchwork/patch/982437/#1177900
 https://lore.kernel.org/patchwork/patch/994091/#1178304

Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit is contained in:
Leonard Crestez 2018-10-08 15:28:01 +00:00 committed by Shawn Guo
parent 1af6ab3bac
commit 1ad9fb750a
1 changed files with 6 additions and 1 deletions

View File

@ -117,7 +117,9 @@
regulator-name = "enet_3v3"; regulator-name = "enet_3v3";
regulator-min-microvolt = <3300000>; regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>; regulator-max-microvolt = <3300000>;
gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; gpio = <&gpio2 6 GPIO_ACTIVE_LOW>;
regulator-boot-on;
regulator-always-on;
}; };
reg_pcie_gpio: regulator-pcie-gpio { reg_pcie_gpio: regulator-pcie-gpio {
@ -180,6 +182,7 @@
phy-supply = <&reg_enet_3v3>; phy-supply = <&reg_enet_3v3>;
phy-mode = "rgmii"; phy-mode = "rgmii";
phy-handle = <&ethphy1>; phy-handle = <&ethphy1>;
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
status = "okay"; status = "okay";
mdio { mdio {
@ -373,6 +376,8 @@
MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081 MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081
MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081 MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081
MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91 MX6SX_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M 0x91
/* phy reset */
MX6SX_PAD_ENET2_CRS__GPIO2_IO_7 0x10b0
>; >;
}; };