Documentation: e1000: Update kernel documentation

Updated the e1000.txt kernel documentation with the latest information.

Also convert the text file to reStructuredText (RST) format, since the
Linux kernel documentation now uses this format for documentation.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
This commit is contained in:
Jeff Kirsher 2018-05-10 12:55:38 -07:00
parent 85d63445f4
commit 228046e761
3 changed files with 12 additions and 50 deletions

View File

@ -154,7 +154,7 @@ NOTE: When e1000 is loaded with default settings and multiple adapters
are in use simultaneously, the CPU utilization may increase non-
linearly. In order to limit the CPU utilization without impacting
the overall throughput, we recommend that you load the driver as
follows:
follows::
modprobe e1000 InterruptThrottleRate=3000,3000,3000
@ -167,8 +167,8 @@ NOTE: When e1000 is loaded with default settings and multiple adapters
RxDescriptors
-------------
Valid Range: 80-256 for 82542 and 82543-based adapters
80-4096 for all other supported adapters
Valid Range: 48-256 for 82542 and 82543-based adapters
48-4096 for all other supported adapters
Default Value: 256
This value specifies the number of receive buffer descriptors allocated
@ -230,8 +230,8 @@ speed. Duplex should also be set when Speed is set to either 10 or 100.
TxDescriptors
-------------
Valid Range: 80-256 for 82542 and 82543-based adapters
80-4096 for all other supported adapters
Valid Range: 48-256 for 82542 and 82543-based adapters
48-4096 for all other supported adapters
Default Value: 256
This value is the number of transmit descriptors allocated by the driver.
@ -242,41 +242,10 @@ NOTE: Depending on the available system resources, the request for a
higher number of transmit descriptors may be denied. In this case,
use a lower number.
TxDescriptorStep
----------------
Valid Range: 1 (use every Tx Descriptor)
4 (use every 4th Tx Descriptor)
Default Value: 1 (use every Tx Descriptor)
On certain non-Intel architectures, it has been observed that intense TX
traffic bursts of short packets may result in an improper descriptor
writeback. If this occurs, the driver will report a "TX Timeout" and reset
the adapter, after which the transmit flow will restart, though data may
have stalled for as much as 10 seconds before it resumes.
The improper writeback does not occur on the first descriptor in a system
memory cache-line, which is typically 32 bytes, or 4 descriptors long.
Setting TxDescriptorStep to a value of 4 will ensure that all TX descriptors
are aligned to the start of a system memory cache line, and so this problem
will not occur.
NOTES: Setting TxDescriptorStep to 4 effectively reduces the number of
TxDescriptors available for transmits to 1/4 of the normal allocation.
This has a possible negative performance impact, which may be
compensated for by allocating more descriptors using the TxDescriptors
module parameter.
There are other conditions which may result in "TX Timeout", which will
not be resolved by the use of the TxDescriptorStep parameter. As the
issue addressed by this parameter has never been observed on Intel
Architecture platforms, it should not be used on Intel platforms.
TxIntDelay
----------
Valid Range: 0-65535 (0=off)
Default Value: 64
Default Value: 8
This value delays the generation of transmit interrupts in units of
1.024 microseconds. Transmit interrupt reduction can improve CPU
@ -288,7 +257,7 @@ TxAbsIntDelay
-------------
(This parameter is supported only on 82540, 82545 and later adapters.)
Valid Range: 0-65535 (0=off)
Default Value: 64
Default Value: 32
This value, in units of 1.024 microseconds, limits the delay in which a
transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
@ -310,7 +279,7 @@ Copybreak
---------
Valid Range: 0-xxxxxxx (0=off)
Default Value: 256
Usage: insmod e1000.ko copybreak=128
Usage: modprobe e1000.ko copybreak=128
Driver copies all packets below or equaling this size to a fresh RX
buffer before handing it up the stack.
@ -328,14 +297,6 @@ Default Value: 0 (disabled)
Allows PHY to turn off in lower power states. The user can turn off
this parameter in supported chipsets.
KumeranLockLoss
---------------
Valid Range: 0-1
Default Value: 1 (enabled)
This workaround skips resetting the PHY at shutdown for the initial
silicon releases of ICH8 systems.
Speed and Duplex Configuration
==============================
@ -397,12 +358,12 @@ Additional Configurations
------------
Jumbo Frames support is enabled by changing the MTU to a value larger than
the default of 1500. Use the ifconfig command to increase the MTU size.
For example:
For example::
ifconfig eth<x> mtu 9000 up
This setting is not saved across reboots. It can be made permanent if
you add:
you add::
MTU=9000

View File

@ -11,6 +11,7 @@ Contents:
can
dpaa2/index
e100
e1000
kapi
z8530book
msg_zerocopy

View File

@ -7090,7 +7090,7 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue.git
T: git git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue.git
S: Supported
F: Documentation/networking/e100.rst
F: Documentation/networking/e1000.txt
F: Documentation/networking/e1000.rst
F: Documentation/networking/e1000e.txt
F: Documentation/networking/igb.txt
F: Documentation/networking/igbvf.txt