soc: qcom: Add irq clear handling during SE init

when the kernel inits a SE, its quite possible we have pending interrupts
from bootloaders which did not handle/clear them. So do this in kernel at
the SE init, to avoid some of it causing bad behavior, while at it also
club all the register writes needed to clear the se irqs into a function
to avoid repeating it over.

Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This commit is contained in:
Alok Chauhan 2018-10-03 17:53:50 +05:30 committed by Andy Gross
parent 651022382c
commit 279536a564
1 changed files with 13 additions and 12 deletions

View File

@ -215,6 +215,16 @@ static void geni_se_io_init(void __iomem *base)
writel_relaxed(FORCE_DEFAULT, base + GENI_FORCE_DEFAULT_REG);
}
static void geni_se_irq_clear(struct geni_se *se)
{
writel_relaxed(0, se->base + SE_GSI_EVENT_EN);
writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR);
writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR);
writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR);
writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR);
writel_relaxed(0xffffffff, se->base + SE_IRQ_EN);
}
/**
* geni_se_init() - Initialize the GENI serial engine
* @se: Pointer to the concerned serial engine.
@ -228,6 +238,7 @@ void geni_se_init(struct geni_se *se, u32 rx_wm, u32 rx_rfr)
{
u32 val;
geni_se_irq_clear(se);
geni_se_io_init(se->base);
geni_se_io_set_mode(se->base);
@ -249,12 +260,7 @@ static void geni_se_select_fifo_mode(struct geni_se *se)
u32 proto = geni_se_read_proto(se);
u32 val;
writel_relaxed(0, se->base + SE_GSI_EVENT_EN);
writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR);
writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR);
writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR);
writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR);
writel_relaxed(0xffffffff, se->base + SE_IRQ_EN);
geni_se_irq_clear(se);
val = readl_relaxed(se->base + SE_GENI_M_IRQ_EN);
if (proto != GENI_SE_UART) {
@ -277,12 +283,7 @@ static void geni_se_select_dma_mode(struct geni_se *se)
{
u32 val;
writel_relaxed(0, se->base + SE_GSI_EVENT_EN);
writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR);
writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR);
writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR);
writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR);
writel_relaxed(0xffffffff, se->base + SE_IRQ_EN);
geni_se_irq_clear(se);
val = readl_relaxed(se->base + SE_GENI_DMA_MODE_EN);
val |= GENI_DMA_MODE_EN;