gpio: Add GPIO support for Broadcom STB SoCs

This adds support for the GPIO IP "UPG GIO" used on
Broadcom STB SoCs (BCM7XXX and some others). Uses
basic_mmio_gpio to instantiate a gpio_chip for each bank.
The driver assumes that it handles the base set of GPIOs
on the system and that it can start its numbering sequence
from 0, so any GPIO expanders used with it must dynamically
assign GPIO numbers after this driver has finished
registering its GPIOs.

Does not implement the interrupt-controller portion yet,
will be done in a future commit.

v2:
- change include to use <linux/gpio/driver.h> instead of
  <linux/gpio.h>
- get rid of unnecessary imask member in struct bank
- rename GPIO_PER_BANK -> MAX_GPIO_PER_BANK
- always have 32 GPIOs per bank and add 'width' member in
  struct bank to hold actual number of GPIOs in use
- mark of_match table as const

List-usage-fixed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit is contained in:
Gregory Fong 2015-05-28 19:14:05 -07:00 committed by Linus Walleij
parent 733cf014f0
commit 3b0213d56e
4 changed files with 268 additions and 0 deletions

View File

@ -2241,6 +2241,13 @@ N: bcm9583*
N: bcm583*
N: bcm113*
BROADCOM BRCMSTB GPIO DRIVER
M: Gregory Fong <gregory.0xf0@gmail.com>
L: bcm-kernel-feedback-list@broadcom.com>
S: Supported
F: drivers/gpio/gpio-brcmstb.c
F: Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
BROADCOM KONA GPIO DRIVER
M: Ray Jui <rjui@broadcom.com>
L: bcm-kernel-feedback-list@broadcom.com

View File

@ -126,6 +126,14 @@ config GPIO_BCM_KONA
help
Turn on GPIO support for Broadcom "Kona" chips.
config GPIO_BRCMSTB
tristate "BRCMSTB GPIO support"
default y if ARCH_BRCMSTB
depends on OF_GPIO && (ARCH_BRCMSTB || COMPILE_TEST)
select GPIO_GENERIC
help
Say yes here to enable GPIO support for Broadcom STB (BCM7XXX) SoCs.
config GPIO_CLPS711X
tristate "CLPS711X GPIO support"
depends on ARCH_CLPS711X || COMPILE_TEST

View File

@ -21,6 +21,7 @@ obj-$(CONFIG_GPIO_ALTERA) += gpio-altera.o
obj-$(CONFIG_GPIO_AMD8111) += gpio-amd8111.o
obj-$(CONFIG_GPIO_ARIZONA) += gpio-arizona.o
obj-$(CONFIG_GPIO_BCM_KONA) += gpio-bcm-kona.o
obj-$(CONFIG_GPIO_BRCMSTB) += gpio-brcmstb.o
obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o
obj-$(CONFIG_GPIO_CLPS711X) += gpio-clps711x.o
obj-$(CONFIG_GPIO_CS5535) += gpio-cs5535.o

252
drivers/gpio/gpio-brcmstb.c Normal file
View File

@ -0,0 +1,252 @@
/*
* Copyright (C) 2015 Broadcom Corporation
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/bitops.h>
#include <linux/gpio/driver.h>
#include <linux/of_device.h>
#include <linux/of_irq.h>
#include <linux/module.h>
#include <linux/basic_mmio_gpio.h>
#define GIO_BANK_SIZE 0x20
#define GIO_ODEN(bank) (((bank) * GIO_BANK_SIZE) + 0x00)
#define GIO_DATA(bank) (((bank) * GIO_BANK_SIZE) + 0x04)
#define GIO_IODIR(bank) (((bank) * GIO_BANK_SIZE) + 0x08)
#define GIO_EC(bank) (((bank) * GIO_BANK_SIZE) + 0x0c)
#define GIO_EI(bank) (((bank) * GIO_BANK_SIZE) + 0x10)
#define GIO_MASK(bank) (((bank) * GIO_BANK_SIZE) + 0x14)
#define GIO_LEVEL(bank) (((bank) * GIO_BANK_SIZE) + 0x18)
#define GIO_STAT(bank) (((bank) * GIO_BANK_SIZE) + 0x1c)
struct brcmstb_gpio_bank {
struct list_head node;
int id;
struct bgpio_chip bgc;
struct brcmstb_gpio_priv *parent_priv;
u32 width;
};
struct brcmstb_gpio_priv {
struct list_head bank_list;
void __iomem *reg_base;
int num_banks;
struct platform_device *pdev;
int gpio_base;
};
#define MAX_GPIO_PER_BANK 32
#define GPIO_BANK(gpio) ((gpio) >> 5)
/* assumes MAX_GPIO_PER_BANK is a multiple of 2 */
#define GPIO_BIT(gpio) ((gpio) & (MAX_GPIO_PER_BANK - 1))
static inline struct brcmstb_gpio_bank *
brcmstb_gpio_gc_to_bank(struct gpio_chip *gc)
{
struct bgpio_chip *bgc = to_bgpio_chip(gc);
return container_of(bgc, struct brcmstb_gpio_bank, bgc);
}
static inline struct brcmstb_gpio_priv *
brcmstb_gpio_gc_to_priv(struct gpio_chip *gc)
{
struct brcmstb_gpio_bank *bank = brcmstb_gpio_gc_to_bank(gc);
return bank->parent_priv;
}
/* Make sure that the number of banks matches up between properties */
static int brcmstb_gpio_sanity_check_banks(struct device *dev,
struct device_node *np, struct resource *res)
{
int res_num_banks = resource_size(res) / GIO_BANK_SIZE;
int num_banks =
of_property_count_u32_elems(np, "brcm,gpio-bank-widths");
if (res_num_banks != num_banks) {
dev_err(dev, "Mismatch in banks: res had %d, bank-widths had %d\n",
res_num_banks, num_banks);
return -EINVAL;
} else {
return 0;
}
}
static int brcmstb_gpio_remove(struct platform_device *pdev)
{
struct brcmstb_gpio_priv *priv = platform_get_drvdata(pdev);
struct list_head *pos;
struct brcmstb_gpio_bank *bank;
int ret = 0;
list_for_each(pos, &priv->bank_list) {
bank = list_entry(pos, struct brcmstb_gpio_bank, node);
ret = bgpio_remove(&bank->bgc);
if (ret)
dev_err(&pdev->dev, "gpiochip_remove fail in cleanup");
}
return ret;
}
static int brcmstb_gpio_of_xlate(struct gpio_chip *gc,
const struct of_phandle_args *gpiospec, u32 *flags)
{
struct brcmstb_gpio_priv *priv = brcmstb_gpio_gc_to_priv(gc);
struct brcmstb_gpio_bank *bank = brcmstb_gpio_gc_to_bank(gc);
int offset;
if (gc->of_gpio_n_cells != 2) {
WARN_ON(1);
return -EINVAL;
}
if (WARN_ON(gpiospec->args_count < gc->of_gpio_n_cells))
return -EINVAL;
offset = gpiospec->args[0] - (gc->base - priv->gpio_base);
if (offset >= gc->ngpio)
return -EINVAL;
if (unlikely(offset >= bank->width)) {
dev_warn_ratelimited(&priv->pdev->dev,
"Received request for invalid GPIO offset %d\n",
gpiospec->args[0]);
}
if (flags)
*flags = gpiospec->args[1];
return offset;
}
static int brcmstb_gpio_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *np = dev->of_node;
void __iomem *reg_base;
struct brcmstb_gpio_priv *priv;
struct resource *res;
struct property *prop;
const __be32 *p;
u32 bank_width;
int err;
static int gpio_base;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
reg_base = devm_ioremap_resource(dev, res);
if (IS_ERR(reg_base))
return PTR_ERR(reg_base);
priv->gpio_base = gpio_base;
priv->reg_base = reg_base;
priv->pdev = pdev;
INIT_LIST_HEAD(&priv->bank_list);
if (brcmstb_gpio_sanity_check_banks(dev, np, res))
return -EINVAL;
of_property_for_each_u32(np, "brcm,gpio-bank-widths", prop, p,
bank_width) {
struct brcmstb_gpio_bank *bank;
struct bgpio_chip *bgc;
struct gpio_chip *gc;
bank = devm_kzalloc(dev, sizeof(*bank), GFP_KERNEL);
if (!bank) {
err = -ENOMEM;
goto fail;
}
bank->parent_priv = priv;
bank->id = priv->num_banks;
if (bank_width <= 0 || bank_width > MAX_GPIO_PER_BANK) {
dev_err(dev, "Invalid bank width %d\n", bank_width);
goto fail;
} else {
bank->width = bank_width;
}
/*
* Regs are 4 bytes wide, have data reg, no set/clear regs,
* and direction bits have 0 = output and 1 = input
*/
bgc = &bank->bgc;
err = bgpio_init(bgc, dev, 4,
reg_base + GIO_DATA(bank->id),
NULL, NULL, NULL,
reg_base + GIO_IODIR(bank->id), 0);
if (err) {
dev_err(dev, "bgpio_init() failed\n");
goto fail;
}
gc = &bgc->gc;
gc->of_node = np;
gc->owner = THIS_MODULE;
gc->label = np->full_name;
gc->base = gpio_base;
gc->of_gpio_n_cells = 2;
gc->of_xlate = brcmstb_gpio_of_xlate;
/* not all ngpio lines are valid, will use bank width later */
gc->ngpio = MAX_GPIO_PER_BANK;
err = gpiochip_add(gc);
if (err) {
dev_err(dev, "Could not add gpiochip for bank %d\n",
bank->id);
goto fail;
}
gpio_base += gc->ngpio;
dev_dbg(dev, "bank=%d, base=%d, ngpio=%d, width=%d\n", bank->id,
gc->base, gc->ngpio, bank->width);
/* Everything looks good, so add bank to list */
list_add(&bank->node, &priv->bank_list);
priv->num_banks++;
}
dev_info(dev, "Registered %d banks (GPIO(s): %d-%d)\n",
priv->num_banks, priv->gpio_base, gpio_base - 1);
platform_set_drvdata(pdev, priv);
return 0;
fail:
(void) brcmstb_gpio_remove(pdev);
return err;
}
static const struct of_device_id brcmstb_gpio_of_match[] = {
{ .compatible = "brcm,brcmstb-gpio" },
{},
};
MODULE_DEVICE_TABLE(of, brcmstb_gpio_of_match);
static struct platform_driver brcmstb_gpio_driver = {
.driver = {
.name = "brcmstb-gpio",
.of_match_table = brcmstb_gpio_of_match,
},
.probe = brcmstb_gpio_probe,
.remove = brcmstb_gpio_remove,
};
module_platform_driver(brcmstb_gpio_driver);
MODULE_AUTHOR("Gregory Fong");
MODULE_DESCRIPTION("Driver for Broadcom BRCMSTB SoC UPG GPIO");
MODULE_LICENSE("GPL v2");