ARM: 5724/1: U300 AB3100 boardinfo v5
This defines regulator platform data and board power regulator hogs for the ST-Ericsson U300 platform. Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Liam Girdwood <lrg@slimlogic.co.uk> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This commit is contained in:
Linus Walleij
Russell King
parent
2fdc246aaf
commit
3d81277b65
|
|
@ -12,3 +12,4 @@ obj-$(CONFIG_MMC) += mmc.o
|
|||
obj-$(CONFIG_SPI_PL022) += spi.o
|
||||
obj-$(CONFIG_MACH_U300_SPIDUMMY) += dummyspichip.o
|
||||
obj-$(CONFIG_I2C_STU300) += i2c.o
|
||||
obj-$(CONFIG_REGULATOR_AB3100) += regulator.o
|
||||
|
|
|
|||
|
|
@ -9,13 +9,256 @@
|
|||
*/
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/mfd/ab3100.h>
|
||||
#include <linux/regulator/machine.h>
|
||||
#include <linux/amba/bus.h>
|
||||
#include <mach/irqs.h>
|
||||
|
||||
/*
|
||||
* Initial settings of ab3100 registers.
|
||||
* Common for below LDO regulator settings are that
|
||||
* bit 7-5 controls voltage. Bit 4 turns regulator ON(1) or OFF(0).
|
||||
* Bit 3-2 controls sleep enable and bit 1-0 controls sleep mode.
|
||||
*/
|
||||
|
||||
/* LDO_A 0x16: 2.75V, ON, SLEEP_A, SLEEP OFF GND */
|
||||
#define LDO_A_SETTING 0x16
|
||||
/* LDO_C 0x10: 2.65V, ON, SLEEP_A or B, SLEEP full power */
|
||||
#define LDO_C_SETTING 0x10
|
||||
/* LDO_D 0x10: 2.65V, ON, sleep mode not used */
|
||||
#define LDO_D_SETTING 0x10
|
||||
/* LDO_E 0x10: 1.8V, ON, SLEEP_A or B, SLEEP full power */
|
||||
#define LDO_E_SETTING 0x10
|
||||
/* LDO_E SLEEP 0x00: 1.8V, not used, SLEEP_A or B, not used */
|
||||
#define LDO_E_SLEEP_SETTING 0x00
|
||||
/* LDO_F 0xD0: 2.5V, ON, SLEEP_A or B, SLEEP full power */
|
||||
#define LDO_F_SETTING 0xD0
|
||||
/* LDO_G 0x00: 2.85V, OFF, SLEEP_A or B, SLEEP full power */
|
||||
#define LDO_G_SETTING 0x00
|
||||
/* LDO_H 0x18: 2.75V, ON, SLEEP_B, SLEEP full power */
|
||||
#define LDO_H_SETTING 0x18
|
||||
/* LDO_K 0x00: 2.75V, OFF, SLEEP_A or B, SLEEP full power */
|
||||
#define LDO_K_SETTING 0x00
|
||||
/* LDO_EXT 0x00: Voltage not set, OFF, not used, not used */
|
||||
#define LDO_EXT_SETTING 0x00
|
||||
/* BUCK 0x7D: 1.2V, ON, SLEEP_A and B, SLEEP low power */
|
||||
#define BUCK_SETTING 0x7D
|
||||
/* BUCK SLEEP 0xAC: 1.05V, Not used, SLEEP_A and B, Not used */
|
||||
#define BUCK_SLEEP_SETTING 0xAC
|
||||
|
||||
static struct regulator_consumer_supply supply_ldo_c[] = {
|
||||
{
|
||||
.dev_name = "ab3100-codec",
|
||||
.supply = "vaudio", /* Powers the codec */
|
||||
},
|
||||
};
|
||||
|
||||
/*
|
||||
* This one needs to be a supply so we can turn it off
|
||||
* in order to shut down the system.
|
||||
*/
|
||||
static struct regulator_consumer_supply supply_ldo_d[] = {
|
||||
{
|
||||
.dev = NULL,
|
||||
.supply = "vana15", /* Powers the SoC (CPU etc) */
|
||||
},
|
||||
};
|
||||
|
||||
static struct regulator_consumer_supply supply_ldo_g[] = {
|
||||
{
|
||||
.dev_name = "mmci",
|
||||
.supply = "vmmc", /* Powers MMC/SD card */
|
||||
},
|
||||
};
|
||||
|
||||
static struct regulator_consumer_supply supply_ldo_h[] = {
|
||||
{
|
||||
.dev_name = "xgam_pdi",
|
||||
.supply = "vdisp", /* Powers camera, display etc */
|
||||
},
|
||||
};
|
||||
|
||||
static struct regulator_consumer_supply supply_ldo_k[] = {
|
||||
{
|
||||
.dev_name = "irda",
|
||||
.supply = "vir", /* Power IrDA */
|
||||
},
|
||||
};
|
||||
|
||||
/*
|
||||
* This is a placeholder for whoever wish to use the
|
||||
* external power.
|
||||
*/
|
||||
static struct regulator_consumer_supply supply_ldo_ext[] = {
|
||||
{
|
||||
.dev = NULL,
|
||||
.supply = "vext", /* External power */
|
||||
},
|
||||
};
|
||||
|
||||
/* Preset (hardware defined) voltages for these regulators */
|
||||
#define LDO_A_VOLTAGE 2750000
|
||||
#define LDO_C_VOLTAGE 2650000
|
||||
#define LDO_D_VOLTAGE 2650000
|
||||
|
||||
static struct ab3100_platform_data ab3100_plf_data = {
|
||||
.reg_constraints = {
|
||||
/* LDO A routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.name = "vrad",
|
||||
.min_uV = LDO_A_VOLTAGE,
|
||||
.max_uV = LDO_A_VOLTAGE,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
.always_on = 1,
|
||||
.boot_on = 1,
|
||||
},
|
||||
},
|
||||
/* LDO C routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.min_uV = LDO_C_VOLTAGE,
|
||||
.max_uV = LDO_C_VOLTAGE,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
},
|
||||
.num_consumer_supplies = ARRAY_SIZE(supply_ldo_c),
|
||||
.consumer_supplies = supply_ldo_c,
|
||||
},
|
||||
/* LDO D routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.min_uV = LDO_D_VOLTAGE,
|
||||
.max_uV = LDO_D_VOLTAGE,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
/*
|
||||
* Actually this is boot_on but we need
|
||||
* to reference count it externally to
|
||||
* be able to shut down the system.
|
||||
*/
|
||||
},
|
||||
.num_consumer_supplies = ARRAY_SIZE(supply_ldo_d),
|
||||
.consumer_supplies = supply_ldo_d,
|
||||
},
|
||||
/* LDO E routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.name = "vio",
|
||||
.min_uV = 1800000,
|
||||
.max_uV = 1800000,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
.valid_ops_mask =
|
||||
REGULATOR_CHANGE_VOLTAGE |
|
||||
REGULATOR_CHANGE_STATUS,
|
||||
.always_on = 1,
|
||||
.boot_on = 1,
|
||||
},
|
||||
},
|
||||
/* LDO F routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.name = "vana25",
|
||||
.min_uV = 2500000,
|
||||
.max_uV = 2500000,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
.valid_ops_mask =
|
||||
REGULATOR_CHANGE_VOLTAGE |
|
||||
REGULATOR_CHANGE_STATUS,
|
||||
.always_on = 1,
|
||||
.boot_on = 1,
|
||||
},
|
||||
},
|
||||
/* LDO G routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.min_uV = 1500000,
|
||||
.max_uV = 2850000,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
.valid_ops_mask =
|
||||
REGULATOR_CHANGE_VOLTAGE |
|
||||
REGULATOR_CHANGE_STATUS,
|
||||
},
|
||||
.num_consumer_supplies = ARRAY_SIZE(supply_ldo_g),
|
||||
.consumer_supplies = supply_ldo_g,
|
||||
},
|
||||
/* LDO H routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.min_uV = 1200000,
|
||||
.max_uV = 2750000,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
.valid_ops_mask =
|
||||
REGULATOR_CHANGE_VOLTAGE |
|
||||
REGULATOR_CHANGE_STATUS,
|
||||
},
|
||||
.num_consumer_supplies = ARRAY_SIZE(supply_ldo_h),
|
||||
.consumer_supplies = supply_ldo_h,
|
||||
},
|
||||
/* LDO K routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.min_uV = 1800000,
|
||||
.max_uV = 2750000,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
.valid_ops_mask =
|
||||
REGULATOR_CHANGE_VOLTAGE |
|
||||
REGULATOR_CHANGE_STATUS,
|
||||
},
|
||||
.num_consumer_supplies = ARRAY_SIZE(supply_ldo_k),
|
||||
.consumer_supplies = supply_ldo_k,
|
||||
},
|
||||
/* External regulator interface. No fixed voltage specified.
|
||||
* If we knew the voltage of the external regulator and it
|
||||
* was connected on the board, we could add the (fixed)
|
||||
* voltage for it here.
|
||||
*/
|
||||
{
|
||||
.constraints = {
|
||||
.min_uV = 0,
|
||||
.max_uV = 0,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
.valid_ops_mask =
|
||||
REGULATOR_CHANGE_STATUS,
|
||||
},
|
||||
.num_consumer_supplies = ARRAY_SIZE(supply_ldo_ext),
|
||||
.consumer_supplies = supply_ldo_ext,
|
||||
},
|
||||
/* Buck converter routing and constraints */
|
||||
{
|
||||
.constraints = {
|
||||
.name = "vcore",
|
||||
.min_uV = 1200000,
|
||||
.max_uV = 1800000,
|
||||
.valid_modes_mask = REGULATOR_MODE_NORMAL,
|
||||
.valid_ops_mask =
|
||||
REGULATOR_CHANGE_VOLTAGE |
|
||||
REGULATOR_CHANGE_STATUS,
|
||||
.always_on = 1,
|
||||
.boot_on = 1,
|
||||
},
|
||||
},
|
||||
},
|
||||
.reg_initvals = {
|
||||
LDO_A_SETTING,
|
||||
LDO_C_SETTING,
|
||||
LDO_E_SETTING,
|
||||
LDO_E_SLEEP_SETTING,
|
||||
LDO_F_SETTING,
|
||||
LDO_G_SETTING,
|
||||
LDO_H_SETTING,
|
||||
LDO_K_SETTING,
|
||||
LDO_EXT_SETTING,
|
||||
BUCK_SETTING,
|
||||
BUCK_SLEEP_SETTING,
|
||||
LDO_D_SETTING,
|
||||
},
|
||||
};
|
||||
|
||||
static struct i2c_board_info __initdata bus0_i2c_board_info[] = {
|
||||
{
|
||||
.type = "ab3100",
|
||||
.addr = 0x48,
|
||||
.irq = IRQ_U300_IRQ0_EXT,
|
||||
.platform_data = &ab3100_plf_data,
|
||||
},
|
||||
};
|
||||
|
||||
|
|
@ -38,6 +281,11 @@ void __init u300_i2c_register_board_devices(void)
|
|||
{
|
||||
i2c_register_board_info(0, bus0_i2c_board_info,
|
||||
ARRAY_SIZE(bus0_i2c_board_info));
|
||||
/*
|
||||
* This makes the core shut down all unused regulators
|
||||
* after all the initcalls have completed.
|
||||
*/
|
||||
regulator_has_full_constraints();
|
||||
i2c_register_board_info(1, bus1_i2c_board_info,
|
||||
ARRAY_SIZE(bus1_i2c_board_info));
|
||||
}
|
||||
|
|
|
|||
|
|
@ -0,0 +1,88 @@
|
|||
/*
|
||||
* arch/arm/mach-u300/regulator.c
|
||||
*
|
||||
* Copyright (C) 2009 ST-Ericsson AB
|
||||
* License terms: GNU General Public License (GPL) version 2
|
||||
* Handle board-bound regulators and board power not related
|
||||
* to any devices.
|
||||
* Author: Linus Walleij <linus.walleij@stericsson.com>
|
||||
*/
|
||||
#include <linux/device.h>
|
||||
#include <linux/signal.h>
|
||||
#include <linux/err.h>
|
||||
#include <linux/regulator/consumer.h>
|
||||
/* Those are just for writing in syscon */
|
||||
#include <linux/io.h>
|
||||
#include <mach/hardware.h>
|
||||
#include <mach/syscon.h>
|
||||
|
||||
/*
|
||||
* Regulators that power the board and chip and which are
|
||||
* not copuled to specific drivers are hogged in these
|
||||
* instances.
|
||||
*/
|
||||
static struct regulator *main_power_15;
|
||||
|
||||
/*
|
||||
* This function is used from pm.h to shut down the system by
|
||||
* resetting all regulators in turn and then disable regulator
|
||||
* LDO D (main power).
|
||||
*/
|
||||
void u300_pm_poweroff(void)
|
||||
{
|
||||
sigset_t old, all;
|
||||
|
||||
sigfillset(&all);
|
||||
if (!sigprocmask(SIG_BLOCK, &all, &old)) {
|
||||
/* Disable LDO D to shut down the system */
|
||||
if (main_power_15)
|
||||
regulator_disable(main_power_15);
|
||||
else
|
||||
pr_err("regulator not available to shut down system\n");
|
||||
(void) sigprocmask(SIG_SETMASK, &old, NULL);
|
||||
}
|
||||
return;
|
||||
}
|
||||
|
||||
/*
|
||||
* Hog the regulators needed to power up the board.
|
||||
*/
|
||||
static int __init u300_init_boardpower(void)
|
||||
{
|
||||
int err;
|
||||
u32 val;
|
||||
|
||||
pr_info("U300: setting up board power\n");
|
||||
main_power_15 = regulator_get(NULL, "vana15");
|
||||
if (IS_ERR(main_power_15)) {
|
||||
pr_err("could not get vana15");
|
||||
return PTR_ERR(main_power_15);
|
||||
}
|
||||
err = regulator_enable(main_power_15);
|
||||
if (err) {
|
||||
pr_err("could not enable vana15\n");
|
||||
return err;
|
||||
}
|
||||
|
||||
/*
|
||||
* On U300 a special system controller register pulls up the DC
|
||||
* until the vana15 (LDO D) regulator comes up. At this point, all
|
||||
* regulators are set and we do not need power control via
|
||||
* DC ON anymore. This function will likely be moved whenever
|
||||
* the rest of the U300 power management is implemented.
|
||||
*/
|
||||
pr_info("U300: disable system controller pull-up\n");
|
||||
val = readw(U300_SYSCON_VBASE + U300_SYSCON_PMCR);
|
||||
val &= ~U300_SYSCON_PMCR_DCON_ENABLE;
|
||||
writew(val, U300_SYSCON_VBASE + U300_SYSCON_PMCR);
|
||||
|
||||
/* Register globally exported PM poweroff hook */
|
||||
pm_power_off = u300_pm_poweroff;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
/*
|
||||
* So at module init time we hog the regulator!
|
||||
*/
|
||||
module_init(u300_init_boardpower);
|
||||
Loading…
Reference in New Issue