tty: serial: qcom_geni_serial: Add early console support

Add early console support in Qualcomm Technologies Inc., GENI based
UART controller.

Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
Karthikeyan Ramasubramanian 2018-05-03 14:14:40 -06:00 committed by Greg Kroah-Hartman
parent ec91df8d3f
commit 43f1831b08
2 changed files with 78 additions and 2 deletions

View File

@ -1025,6 +1025,12 @@
address. The serial port must already be setup
and configured. Options are not yet supported.
qcom_geni,<addr>
Start an early, polled-mode console on a Qualcomm
Generic Interface (GENI) based serial port at the
specified address. The serial port must already be
setup and configured. Options are not yet supported.
earlyprintk= [X86,SH,ARM,M68k,S390]
earlyprintk=vga
earlyprintk=efi

View File

@ -196,8 +196,19 @@ static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500;
}
return !readl_poll_timeout_atomic(uport->membase + offset, reg,
(bool)(reg & field) == set, 10, timeout_us);
/*
* Use custom implementation instead of readl_poll_atomic since ktimer
* is not ready at the time of early console.
*/
timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10;
while (timeout_us) {
reg = readl_relaxed(uport->membase + offset);
if ((bool)(reg & field) == set)
return true;
udelay(10);
timeout_us -= 10;
}
return false;
}
static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size)
@ -943,6 +954,65 @@ static int __init qcom_geni_console_setup(struct console *co, char *options)
return uart_set_options(uport, co, baud, parity, bits, flow);
}
static void qcom_geni_serial_earlycon_write(struct console *con,
const char *s, unsigned int n)
{
struct earlycon_device *dev = con->data;
__qcom_geni_serial_console_write(&dev->port, s, n);
}
static int __init qcom_geni_serial_earlycon_setup(struct earlycon_device *dev,
const char *opt)
{
struct uart_port *uport = &dev->port;
u32 tx_trans_cfg;
u32 tx_parity_cfg = 0; /* Disable Tx Parity */
u32 rx_trans_cfg = 0;
u32 rx_parity_cfg = 0; /* Disable Rx Parity */
u32 stop_bit_len = 0; /* Default stop bit length - 1 bit */
u32 bits_per_char;
struct geni_se se;
if (!uport->membase)
return -EINVAL;
memset(&se, 0, sizeof(se));
se.base = uport->membase;
if (geni_se_read_proto(&se) != GENI_SE_UART)
return -ENXIO;
/*
* Ignore Flow control.
* n = 8.
*/
tx_trans_cfg = UART_CTS_MASK;
bits_per_char = BITS_PER_BYTE;
/*
* Make an unconditional cancel on the main sequencer to reset
* it else we could end up in data loss scenarios.
*/
qcom_geni_serial_poll_tx_done(uport);
qcom_geni_serial_abort_rx(uport);
geni_se_config_packing(&se, BITS_PER_BYTE, 1, false, true, false);
geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2);
geni_se_select_mode(&se, GENI_SE_FIFO);
writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
dev->con->write = qcom_geni_serial_earlycon_write;
dev->con->setup = NULL;
return 0;
}
OF_EARLYCON_DECLARE(qcom_geni, "qcom,geni-debug-uart",
qcom_geni_serial_earlycon_setup);
static int __init console_register(struct uart_driver *drv)
{
return uart_register_driver(drv);