From b4e6153704dda5bef78dd59324205b5e61829499 Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Mon, 18 Feb 2013 23:11:30 -0500 Subject: [PATCH 01/37] ARM: mach-imx: move early resume code out of the .data section Building the kernel with allyesconfig fails because the i.mx early resume code located in the .data section is unable to fixup the bl relocation as the branch target gets too far away. The idea of having code in the .data section allows for easy access to nearby data using relative addressing while the MMU is off. However it is probably best to move the code back to the .text section where it belongs and fixup the data access instead. This solves the bl reloc issue (at least until this becomes a general problem) and simplifies the code as well. Signed-off-by: Nicolas Pitre Signed-off-by: Shawn Guo --- arch/arm/mach-imx/headsmp.S | 18 +++++++++--------- arch/arm/mach-imx/pm-imx6q.c | 15 --------------- 2 files changed, 9 insertions(+), 24 deletions(-) diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S index 921fc1555854..a58c8b0527cc 100644 --- a/arch/arm/mach-imx/headsmp.S +++ b/arch/arm/mach-imx/headsmp.S @@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup) #ifdef CONFIG_PM /* - * The following code is located into the .data section. This is to - * allow phys_l2x0_saved_regs to be accessed with a relative load - * as we are running on physical address here. + * The following code must assume it is running from physical address + * where absolute virtual addresses to the data section have to be + * turned into relative ones. */ - .data - .align #ifdef CONFIG_CACHE_L2X0 .macro pl310_resume - ldr r2, phys_l2x0_saved_regs + adr r0, l2x0_saved_regs_offset + ldr r2, [r0] + add r2, r2, r0 ldr r0, [r2, #L2X0_R_PHY_BASE] @ get physical base of l2x0 ldr r1, [r2, #L2X0_R_AUX_CTRL] @ get aux_ctrl value str r1, [r0, #L2X0_AUX_CTRL] @ restore aux_ctrl @@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup) str r1, [r0, #L2X0_CTRL] @ re-enable L2 .endm - .globl phys_l2x0_saved_regs -phys_l2x0_saved_regs: - .long 0 +l2x0_saved_regs_offset: + .word l2x0_saved_regs - . + #else .macro pl310_resume .endm diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c index ee42d20cba19..5faba7a3c95f 100644 --- a/arch/arm/mach-imx/pm-imx6q.c +++ b/arch/arm/mach-imx/pm-imx6q.c @@ -22,8 +22,6 @@ #include "common.h" #include "hardware.h" -extern unsigned long phys_l2x0_saved_regs; - static int imx6q_suspend_finish(unsigned long val) { cpu_do_idle(); @@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = { void __init imx6q_pm_init(void) { - /* - * The l2x0 core code provides an infrastucture to save and restore - * l2x0 registers across suspend/resume cycle. But because imx6q - * retains L2 content during suspend and needs to resume L2 before - * MMU is enabled, it can only utilize register saving support and - * have to take care of restoring on its own. So we save physical - * address of the data structure used by l2x0 core to save registers, - * and later restore the necessary ones in imx6q resume entry. - */ -#ifdef CONFIG_CACHE_L2X0 - phys_l2x0_saved_regs = __pa(&l2x0_saved_regs); -#endif - suspend_set_ops(&imx6q_pm_ops); } From 0545c798e9bb7fe29606681653c20d68e47f4840 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Tue, 19 Feb 2013 15:25:47 +0800 Subject: [PATCH 02/37] ARM: dts: imx53-mba53: fix fsl,pins for disp1-grp1 According to fsl,imx53-pinctrl.txt, the pin number of DISP1_DAT_21 should be 545, while 543 is IPU_CSI0_D_3. Along with the change, one duplication of DISP1_DAT_0 in disp1-grp1 is removed. Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx53-mba53.dts | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/imx53-mba53.dts index e54fffd48369..468c0a1d48d9 100644 --- a/arch/arm/boot/dts/imx53-mba53.dts +++ b/arch/arm/boot/dts/imx53-mba53.dts @@ -42,10 +42,9 @@ fsl,pins = <689 0x10000 /* DISP1_DRDY */ 482 0x10000 /* DISP1_HSYNC */ 489 0x10000 /* DISP1_VSYNC */ - 684 0x10000 /* DISP1_DAT_0 */ 515 0x10000 /* DISP1_DAT_22 */ 523 0x10000 /* DISP1_DAT_23 */ - 543 0x10000 /* DISP1_DAT_21 */ + 545 0x10000 /* DISP1_DAT_21 */ 553 0x10000 /* DISP1_DAT_20 */ 558 0x10000 /* DISP1_DAT_19 */ 564 0x10000 /* DISP1_DAT_18 */ From f6c49da98dd6eacb85034d21d16e1428e03e190f Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 27 Feb 2013 14:03:58 -0300 Subject: [PATCH 03/37] ARM: mxs_defconfig: Make USB host functional again commit 09f6ffde2e (USB: EHCI: fix build error by making ChipIdea host a normal EHCI driver) introduced CONFIG_USB_EHCI_HCD as a dependency for USB_CHIPIDEA_HOST. Select CONFIG_USB_EHCI_HCD, so that USB host can be functional again. Cc: # 3.8 Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/configs/mxs_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig index fbbc5bb022d5..6a99e30f81d2 100644 --- a/arch/arm/configs/mxs_defconfig +++ b/arch/arm/configs/mxs_defconfig @@ -116,6 +116,7 @@ CONFIG_SND_SOC=y CONFIG_SND_MXS_SOC=y CONFIG_SND_SOC_MXS_SGTL5000=y CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y CONFIG_USB_CHIPIDEA=y CONFIG_USB_CHIPIDEA_HOST=y CONFIG_USB_STORAGE=y From bb39cdc52f4278614579c1041155a7b182f47e75 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Mon, 11 Feb 2013 12:01:46 -0200 Subject: [PATCH 04/37] ARM: mxs: mm: Fix sparse warning Include header to fix the following sparse warnings: arch/arm/mach-mxs/mm.c:43:13: warning: symbol 'mx23_map_io' was not declared. Should it be static? arch/arm/mach-mxs/mm.c:48:13: warning: symbol 'mx28_map_io' was not declared. Should it be static? Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/mach-mxs/mm.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/mach-mxs/mm.c b/arch/arm/mach-mxs/mm.c index a4294aa9f301..e63b7d87acbd 100644 --- a/arch/arm/mach-mxs/mm.c +++ b/arch/arm/mach-mxs/mm.c @@ -18,6 +18,7 @@ #include #include +#include /* * Define the MX23 memory map. From f26b016e7aeeebe793eb03e609baac80e1b02947 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Mon, 11 Feb 2013 12:01:47 -0200 Subject: [PATCH 05/37] ARM: mxs: icoll: Fix sparse warning Fix the following sparse warning: arch/arm/mach-mxs/icoll.c:103:13: warning: symbol 'icoll_of_init' was not declared. Should it be static? Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/mach-mxs/icoll.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-mxs/icoll.c b/arch/arm/mach-mxs/icoll.c index 8fb23af154b3..e26eeba46598 100644 --- a/arch/arm/mach-mxs/icoll.c +++ b/arch/arm/mach-mxs/icoll.c @@ -100,7 +100,7 @@ static struct irq_domain_ops icoll_irq_domain_ops = { .xlate = irq_domain_xlate_onecell, }; -void __init icoll_of_init(struct device_node *np, +static void __init icoll_of_init(struct device_node *np, struct device_node *interrupt_parent) { /* From 95381f38c0ed85be732553bf56f613ce701d411b Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Mon, 11 Feb 2013 12:01:48 -0200 Subject: [PATCH 06/37] ARM: mxs: ocotp: Fix sparse warning Include header to fix the following sparse warning: arch/arm/mach-mxs/ocotp.c:33:11: warning: symbol 'mxs_get_ocotp' was not declared. Should it be static? Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/mach-mxs/ocotp.c | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/mach-mxs/ocotp.c b/arch/arm/mach-mxs/ocotp.c index 54add60f94c9..1dff46703753 100644 --- a/arch/arm/mach-mxs/ocotp.c +++ b/arch/arm/mach-mxs/ocotp.c @@ -19,6 +19,7 @@ #include /* for cpu_relax() */ #include +#include #define OCOTP_WORD_OFFSET 0x20 #define OCOTP_WORD_COUNT 0x20 From 0adcbaf78f6267baf4eecc201107d8f8ff3b200c Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 11 Feb 2013 14:46:00 -0800 Subject: [PATCH 07/37] ARM: OMAP1: Fix build related to kgdb.h no longer including serial_8250.h MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Commit 16559ae4 (kgdb: remove #include from kgdb.h) had a side effect of breaking omap1_defconfig build as some headers were included indirectly: arch/arm/mach-omap1/board-h2.c:249: error: ‘INT_KEYBOARD’ undeclared here (not in a function) ... This worked earlier as linux/serial_8250.h included linux/serial_core.h, via linux/serial_8250.h from linux/kgdb.h. Fix this by including the necessary headers directly. Signed-off-by: Tony Lindgren --- arch/arm/mach-omap1/common.h | 2 ++ drivers/video/omap/lcd_ams_delta.c | 1 + drivers/video/omap/lcd_osk.c | 3 +++ 3 files changed, 6 insertions(+) diff --git a/arch/arm/mach-omap1/common.h b/arch/arm/mach-omap1/common.h index fb18831e88aa..14f7e9920479 100644 --- a/arch/arm/mach-omap1/common.h +++ b/arch/arm/mach-omap1/common.h @@ -31,6 +31,8 @@ #include +#include + #if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850) void omap7xx_map_io(void); #else diff --git a/drivers/video/omap/lcd_ams_delta.c b/drivers/video/omap/lcd_ams_delta.c index ed4cad87fbcd..4a5f2cd3d3bf 100644 --- a/drivers/video/omap/lcd_ams_delta.c +++ b/drivers/video/omap/lcd_ams_delta.c @@ -27,6 +27,7 @@ #include #include +#include #include #include "omapfb.h" diff --git a/drivers/video/omap/lcd_osk.c b/drivers/video/omap/lcd_osk.c index 3aa62da89195..7fbe04bce0ed 100644 --- a/drivers/video/omap/lcd_osk.c +++ b/drivers/video/omap/lcd_osk.c @@ -24,7 +24,10 @@ #include #include + +#include #include + #include "omapfb.h" static int osk_panel_init(struct lcd_panel *panel, struct omapfb_device *fbdev) From 31d9adca82ce65e5c99d045b5fd917c702b6fce3 Mon Sep 17 00:00:00 2001 From: Jon Hunter Date: Mon, 18 Feb 2013 07:57:39 -0600 Subject: [PATCH 08/37] ARM: OMAP2+: Fix broken gpmc support Commit 6797b4fe (ARM: OMAP2+: Prevent potential crash if GPMC probe fails) added code to ensure that GPMC chip-selects could not be requested until the device probe was successful. The chip-selects should have been unreserved at the end of the probe function, but the code to unreserve them appears to have ended up in the gpmc_calc_timings() function and hence, this is causing problems requesting chip-selects. Fix this merge error by unreserving the chip-selects at the end of the probe, but before we call the gpmc child probe functions (for device-tree) which request a chip-select. Signed-off-by: Jon Hunter Tested-by: Ezequiel Garcia Tested-by: Philip Avinash Tested-by: Grazvydas Ignotas [tony@atomide.com: updated description to add breaking commit id] Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/gpmc.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index e4b16c8efe8b..410e1bac7815 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -1122,9 +1122,6 @@ int gpmc_calc_timings(struct gpmc_timings *gpmc_t, /* TODO: remove, see function definition */ gpmc_convert_ps_to_ns(gpmc_t); - /* Now the GPMC is initialised, unreserve the chip-selects */ - gpmc_cs_map = 0; - return 0; } @@ -1383,6 +1380,9 @@ static int gpmc_probe(struct platform_device *pdev) if (IS_ERR_VALUE(gpmc_setup_irq())) dev_warn(gpmc_dev, "gpmc_setup_irq failed\n"); + /* Now the GPMC is initialised, unreserve the chip-selects */ + gpmc_cs_map = 0; + rc = gpmc_probe_dt(pdev); if (rc < 0) { clk_disable_unprepare(gpmc_l3_clk); From 990fa4f537092551464a86928c1a056788183101 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Tue, 19 Feb 2013 18:28:31 +0530 Subject: [PATCH 09/37] ARM: OMAP3: board-generic: Add missing omap3_init_late The .init_late callback for OMAP3 has been missing for DT builds, which causes a lot of late PM initializations to be missed in turn. Signed-off-by: Rajendra Nayak Acked-by: Santosh Shilimkar Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-generic.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 0274ff7a2a2b..e54a48060198 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -102,6 +102,7 @@ DT_MACHINE_START(OMAP3_DT, "Generic OMAP3 (Flattened Device Tree)") .init_irq = omap_intc_of_init, .handle_irq = omap3_intc_handle_irq, .init_machine = omap_generic_init, + .init_late = omap3_init_late, .init_time = omap3_sync32k_timer_init, .dt_compat = omap3_boards_compat, .restart = omap3xxx_restart, @@ -119,6 +120,7 @@ DT_MACHINE_START(OMAP3_GP_DT, "Generic OMAP3-GP (Flattened Device Tree)") .init_irq = omap_intc_of_init, .handle_irq = omap3_intc_handle_irq, .init_machine = omap_generic_init, + .init_late = omap3_init_late, .init_time = omap3_secure_sync32k_timer_init, .dt_compat = omap3_gp_boards_compat, .restart = omap3xxx_restart, From 8a6201b9ea71b521557d25e356eef640176899df Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 4 Mar 2013 10:28:21 -0800 Subject: [PATCH 10/37] ARM: OMAP2+: Fix unmet direct dependencies for zoom for 8250 serial We should not select drivers from kconfig as they should by default be optional. Otherwise we'll be chasing broken dependencies forever: warning: (MACH_OMAP_ZOOM2 && MACH_OMAP_ZOOM3 && MWAVE) selects SERIAL_8250 which has unmet direct dependencies (TTY && HAS_IOMEM && GENERIC_HARDIRQS) Fix the issue by removing the selects for zoom and add them to omap2plus_defconfig. Reported-by: Russell King Signed-off-by: Tony Lindgren --- arch/arm/configs/omap2plus_defconfig | 2 ++ arch/arm/mach-omap2/Kconfig | 6 ------ 2 files changed, 2 insertions(+), 6 deletions(-) diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index b16bae2c9a60..bd07864f14a0 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -126,6 +126,8 @@ CONFIG_INPUT_MISC=y CONFIG_INPUT_TWL4030_PWRBUTTON=y CONFIG_VT_HW_CONSOLE_BINDING=y # CONFIG_LEGACY_PTYS is not set +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=32 CONFIG_SERIAL_8250_EXTENDED=y CONFIG_SERIAL_8250_MANY_PORTS=y diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 49ac3dfebef9..8111cd9ff3e5 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -311,9 +311,6 @@ config MACH_OMAP_ZOOM2 default y select OMAP_PACKAGE_CBB select REGULATOR_FIXED_VOLTAGE if REGULATOR - select SERIAL_8250 - select SERIAL_8250_CONSOLE - select SERIAL_CORE_CONSOLE config MACH_OMAP_ZOOM3 bool "OMAP3630 Zoom3 board" @@ -321,9 +318,6 @@ config MACH_OMAP_ZOOM3 default y select OMAP_PACKAGE_CBP select REGULATOR_FIXED_VOLTAGE if REGULATOR - select SERIAL_8250 - select SERIAL_8250_CONSOLE - select SERIAL_CORE_CONSOLE config MACH_CM_T35 bool "CompuLab CM-T35/CM-T3730 modules" From 0fa26ce9f3fbaf517f752283f5b7efc5cbb51916 Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Tue, 19 Feb 2013 12:24:23 +0200 Subject: [PATCH 11/37] ARM: OMAP2+: mux: fix debugfs file permission OMAP's debugfs interface creates one file for each signal in the mux table, such file provides a read method but didn't provide read permission. Fix it. Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/mux.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 6a217c98db54..03fa4f4d3cf5 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -739,8 +739,9 @@ static void __init omap_mux_dbg_create_entry( list_for_each_entry(e, &partition->muxmodes, node) { struct omap_mux *m = &e->mux; - (void)debugfs_create_file(m->muxnames[0], S_IWUSR, mux_dbg_dir, - m, &omap_mux_dbg_signal_fops); + (void)debugfs_create_file(m->muxnames[0], S_IWUSR | S_IRUGO, + mux_dbg_dir, m, + &omap_mux_dbg_signal_fops); } } From 39bb356ee60581c3d28d6a636e5f221006d95f0c Mon Sep 17 00:00:00 2001 From: Ruslan Bilovol Date: Sun, 3 Feb 2013 02:15:10 +0200 Subject: [PATCH 12/37] ARM: OMAP2+: mux: correct wrong error messages This is needed because the omap_mux_get_by_name() function calls the _omap_mux_get_by_name subfunction for each mux partition until needed mux is not found. As a result, we get messages like "Could not find signal XXX" for each partition where this mux name does not exist. This patch fixes wrong error message in the _omap_mux_get_by_name() function moving it to the omap_mux_get_by_name() one and as result reduces noise in the kernel log. My kernel log without this patch: [...] [ 0.221801] omap_mux_init: Add partition: #2: wkup, flags: 3 [ 0.222045] _omap_mux_get_by_name: Could not find signal fref_clk0_out.sys_drm_msecure [ 0.222137] _omap_mux_get_by_name: Could not find signal sys_nirq [ 0.222167] _omap_mux_get_by_name: Could not find signal sys_nirq [ 0.225006] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx [ 0.225006] _omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx [ 0.270111] _omap_mux_get_by_name: Could not find signal fref_clk4_out.fref_clk4_out [ 0.273406] twl: not initialized [...] My kernel log with this patch: [...] [ 0.221771] omap_mux_init: Add partition: #2: wkup, flags: 3 [ 0.222106] omap_mux_get_by_name: Could not find signal sys_nirq [ 0.224945] omap_mux_get_by_name: Could not find signal uart1_rx.uart1_rx [ 0.274536] twl: not initialized [...] Signed-off-by: Ruslan Bilovol Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/mux.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 03fa4f4d3cf5..f82cf878d6af 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -211,8 +211,6 @@ static int __init _omap_mux_get_by_name(struct omap_mux_partition *partition, return -EINVAL; } - pr_err("%s: Could not find signal %s\n", __func__, muxname); - return -ENODEV; } @@ -234,6 +232,8 @@ int __init omap_mux_get_by_name(const char *muxname, return mux_mode; } + pr_err("%s: Could not find signal %s\n", __func__, muxname); + return -ENODEV; } From 08913c2d2445da9f17a32186418e61baa4ae85b6 Mon Sep 17 00:00:00 2001 From: Santosh Shilimkar Date: Fri, 8 Feb 2013 20:41:45 +0530 Subject: [PATCH 13/37] ARM: OMAP2+: Remove duplicate omap4430_init_late() declaration Commit bbd707ac {ARM: omap2: use machine specific hook for late init} accidentally added two declarations for omap4430_init_late(). Remove the duplicate declaration. Cc: Shawn Guo Signed-off-by: Santosh Shilimkar Reviewed-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/common.h | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h index 0a6b9c7a63da..40f4a03d728f 100644 --- a/arch/arm/mach-omap2/common.h +++ b/arch/arm/mach-omap2/common.h @@ -108,7 +108,6 @@ void omap35xx_init_late(void); void omap3630_init_late(void); void am35xx_init_late(void); void ti81xx_init_late(void); -void omap4430_init_late(void); int omap2_common_pm_late_init(void); #if defined(CONFIG_SOC_OMAP2420) || defined(CONFIG_SOC_OMAP2430) From 91bdf0d0c48c9254fb73037bfb8ee1777093225b Mon Sep 17 00:00:00 2001 From: Javi Merino Date: Tue, 19 Feb 2013 13:52:22 +0000 Subject: [PATCH 14/37] irqchip: fix typo when moving gic_raise_softirq() In b1cffebf (ARM: GIC: remove direct use of gic_raise_softirq) gic_raise_softirq() was moved inside arch/arm/common/gic.c but in the process it reverted by mistake a change to that function made by 384a290 (ARM: gic: use a private mapping for CPU target interfaces). This breaks multicluster systems on ARM. This patch fixes the typo. Signed-off-by: Javi Merino Acked-by: Rob Herring Signed-off-by: Olof Johansson --- drivers/irqchip/irq-gic.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/irqchip/irq-gic.c b/drivers/irqchip/irq-gic.c index 644d72468423..a32e0d5aa45f 100644 --- a/drivers/irqchip/irq-gic.c +++ b/drivers/irqchip/irq-gic.c @@ -648,7 +648,7 @@ void gic_raise_softirq(const struct cpumask *mask, unsigned int irq) /* Convert our logical CPU mask into a physical one. */ for_each_cpu(cpu, mask) - map |= 1 << cpu_logical_map(cpu); + map |= gic_cpu_map[cpu]; /* * Ensure that stores to Normal memory are visible to the From 2837a1d4161caec7dffefa03505b87f056c1f5bb Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Thu, 21 Feb 2013 22:42:38 -0700 Subject: [PATCH 15/37] ARM: bcm2835: fix I2C module clock rate BCM2835-ARM-Peripherals.pdf states that the I2C module's input clock is nominally 150MHz, and that value is currently reflected in bcm2835.dtsi. However, practical measurements show that the rate is actually 250MHz, and this agrees with various downstream kernels. Switch the I2C clock's frequency to 250MHz so that the generated bus clock rate is accurate. Signed-off-by: Stephen Warren Signed-off-by: Olof Johansson --- arch/arm/boot/dts/bcm2835.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi index 4bf2a8774aa7..7e0481e2441a 100644 --- a/arch/arm/boot/dts/bcm2835.dtsi +++ b/arch/arm/boot/dts/bcm2835.dtsi @@ -105,7 +105,7 @@ compatible = "fixed-clock"; reg = <1>; #clock-cells = <0>; - clock-frequency = <150000000>; + clock-frequency = <250000000>; }; }; }; From 9e25fe6b339f5d66cc4d1f3723d5246bf727586d Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 22 Jan 2013 15:27:29 -0600 Subject: [PATCH 16/37] ARM: dts: remove generated .dtb files on clean commit 5f300acd8ae9f3d4585154370012ffc5c665330f (ARM: 7152/1: distclean: Remove generated .dtb files) ensured that dtbs were cleaned up when they were in arch/arm/boot. However, with the following commit: commit 499cd8298628eeabf0eb5eb6525d4faa0eec80d8 (ARM: dt: change .dtb build rules to build in dts directory) make clean now leaves dtbs in arch/arm/boot/dts/ untouched. Include dts directory so that clean-files rule from arch/arm/boot/dts/Makefile is invoked when make clean is done. Cc: Dirk Behme CC: Grant Likely Signed-off-by: Nishanth Menon Signed-off-by: Olof Johansson --- arch/arm/boot/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile index 71768b8a1ab9..84aa2caf07ed 100644 --- a/arch/arm/boot/Makefile +++ b/arch/arm/boot/Makefile @@ -115,4 +115,4 @@ i: $(CONFIG_SHELL) $(srctree)/$(src)/install.sh $(KERNELRELEASE) \ $(obj)/Image System.map "$(INSTALL_PATH)" -subdir- := bootp compressed +subdir- := bootp compressed dts From ed3ced371146f0993f0e4f315720449d78dc7032 Mon Sep 17 00:00:00 2001 From: Prashant Gaikwad Date: Fri, 1 Mar 2013 11:32:24 -0700 Subject: [PATCH 17/37] ARM: Tegra: Add clock entry for smp_twd clock As DT support for clocks and smp_twd is enabled, add clock entry for smp_twd clock to DT. This fixes the following error while booting the kernel: smp_twd: clock not found -2 Signed-off-by: Prashant Gaikwad [swarren: include kernel log spew that this fixes] Signed-off-by: Stephen Warren Signed-off-by: Olof Johansson --- arch/arm/boot/dts/tegra20.dtsi | 1 + arch/arm/boot/dts/tegra30.dtsi | 1 + 2 files changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi index 9a428931d042..48d00a099ce3 100644 --- a/arch/arm/boot/dts/tegra20.dtsi +++ b/arch/arm/boot/dts/tegra20.dtsi @@ -118,6 +118,7 @@ compatible = "arm,cortex-a9-twd-timer"; reg = <0x50040600 0x20>; interrupts = <1 13 0x304>; + clocks = <&tegra_car 132>; }; intc: interrupt-controller { diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi index 767803e1fd55..9d87a3ffe998 100644 --- a/arch/arm/boot/dts/tegra30.dtsi +++ b/arch/arm/boot/dts/tegra30.dtsi @@ -119,6 +119,7 @@ compatible = "arm,cortex-a9-twd-timer"; reg = <0x50040600 0x20>; interrupts = <1 13 0xf04>; + clocks = <&tegra_car 214>; }; intc: interrupt-controller { From 984b839337da1eb7b4a4fb50e24cf28c2b473862 Mon Sep 17 00:00:00 2001 From: Prashant Gaikwad Date: Fri, 1 Mar 2013 11:32:25 -0700 Subject: [PATCH 18/37] clk: Tegra: Remove duplicate smp_twd clock Remove duplicate smp_twd clocks as these clocks are accessed using DT now. Signed-off-by: Prashant Gaikwad Signed-off-by: Stephen Warren Signed-off-by: Olof Johansson --- drivers/clk/tegra/clk-tegra20.c | 1 - drivers/clk/tegra/clk-tegra30.c | 1 - 2 files changed, 2 deletions(-) diff --git a/drivers/clk/tegra/clk-tegra20.c b/drivers/clk/tegra/clk-tegra20.c index 143ce1f899ad..1e2de7305362 100644 --- a/drivers/clk/tegra/clk-tegra20.c +++ b/drivers/clk/tegra/clk-tegra20.c @@ -1292,7 +1292,6 @@ static struct tegra_clk_duplicate tegra_clk_duplicates[] = { TEGRA_CLK_DUPLICATE(usbd, "tegra-ehci.0", NULL), TEGRA_CLK_DUPLICATE(usbd, "tegra-otg", NULL), TEGRA_CLK_DUPLICATE(cclk, NULL, "cpu"), - TEGRA_CLK_DUPLICATE(twd, "smp_twd", NULL), TEGRA_CLK_DUPLICATE(clk_max, NULL, NULL), /* Must be the last entry */ }; diff --git a/drivers/clk/tegra/clk-tegra30.c b/drivers/clk/tegra/clk-tegra30.c index 32c61cb6d0bb..ba6f51bc9f3b 100644 --- a/drivers/clk/tegra/clk-tegra30.c +++ b/drivers/clk/tegra/clk-tegra30.c @@ -1931,7 +1931,6 @@ static struct tegra_clk_duplicate tegra_clk_duplicates[] = { TEGRA_CLK_DUPLICATE(cml1, "tegra_sata_cml", NULL), TEGRA_CLK_DUPLICATE(cml0, "tegra_pcie", "cml"), TEGRA_CLK_DUPLICATE(pciex, "tegra_pcie", "pciex"), - TEGRA_CLK_DUPLICATE(twd, "smp_twd", NULL), TEGRA_CLK_DUPLICATE(vcp, "nvavp", "vcp"), TEGRA_CLK_DUPLICATE(clk_max, NULL, NULL), /* MUST be the last entry */ }; From b0ad0995e92fdf6b25056da76c906c51bb06d6a5 Mon Sep 17 00:00:00 2001 From: Aaro Koskinen Date: Tue, 5 Mar 2013 13:09:40 +0200 Subject: [PATCH 19/37] ARM: OMAP: RX-51: add missing USB phy binding Commit 51482be9 (ARM: OMAP: USB: Add phy binding information) forgot to add phy binding for RX-51, and as a result USB does not work anymore on 3.9-rc1. Add the missing binding. Signed-off-by: Aaro Koskinen Reviewed-by: Kishon Vijay Abraham I Acked-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-rx51.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index f7c4616cbb60..d2ea68ea678a 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include @@ -98,6 +99,7 @@ static void __init rx51_init(void) sdrc_params = nokia_get_sdram_timings(); omap_sdrc_init(sdrc_params, sdrc_params); + usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(&musb_board_data); rx51_peripherals_init(); From 51c66cf9695f389126119e4cd7a50b832648f11e Mon Sep 17 00:00:00 2001 From: Paul Bolle Date: Tue, 5 Mar 2013 10:13:39 +0100 Subject: [PATCH 20/37] ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ" Do what commit f12a500e4adcc0961803e54b5ed1e74275d399f1 ("ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ") wanted to do. Signed-off-by: Paul Bolle Acked-by: Viresh Kumar Signed-off-by: Arnd Bergmann --- arch/arm/plat-spear/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/plat-spear/Kconfig b/arch/arm/plat-spear/Kconfig index 739d016eb273..8a08c31b5e20 100644 --- a/arch/arm/plat-spear/Kconfig +++ b/arch/arm/plat-spear/Kconfig @@ -10,7 +10,7 @@ choice config ARCH_SPEAR13XX bool "ST SPEAr13xx with Device Tree" - select ARCH_HAVE_CPUFREQ + select ARCH_HAS_CPUFREQ select ARM_GIC select CPU_V7 select GPIO_SPEAR_SPICS From 4a38a8502b0ea4ecbe86f60e0b2416771c51888d Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Tue, 5 Mar 2013 16:13:35 +0100 Subject: [PATCH 21/37] ARM: mxs: cfa10049: Fix fb initialisation function Commit 1fe42740 ("ARM: dts: mxs: Add the LCD to the 10049 board") seem to have been applied with some fuzzyness, and the framebuffer initialisation code for the CFA-10049 ended up in the CFA-10037 initialisation function. Signed-off-by: Maxime Ripard Signed-off-by: Shawn Guo --- arch/arm/mach-mxs/mach-mxs.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c index 052186713347..3218f1f2c0e0 100644 --- a/arch/arm/mach-mxs/mach-mxs.c +++ b/arch/arm/mach-mxs/mach-mxs.c @@ -402,17 +402,17 @@ static void __init cfa10049_init(void) { enable_clk_enet_out(); update_fec_mac_prop(OUI_CRYSTALFONTZ); + + mxsfb_pdata.mode_list = cfa10049_video_modes; + mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes); + mxsfb_pdata.default_bpp = 32; + mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT; } static void __init cfa10037_init(void) { enable_clk_enet_out(); update_fec_mac_prop(OUI_CRYSTALFONTZ); - - mxsfb_pdata.mode_list = cfa10049_video_modes; - mxsfb_pdata.mode_count = ARRAY_SIZE(cfa10049_video_modes); - mxsfb_pdata.default_bpp = 32; - mxsfb_pdata.ld_intf_width = STMLCDIF_18BIT; } static void __init apf28_init(void) From 93fff4ce19f9978cc1c59db42760717477939249 Mon Sep 17 00:00:00 2001 From: Jason Cooper Date: Tue, 29 Jan 2013 20:36:43 +0000 Subject: [PATCH 22/37] ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency When DT support for kirkwood was first introduced, there was no clock infrastructure. As a result, we had to manually pass the clock-frequency to the driver from the device node. Unfortunately, on kirkwood, with minimal config or all module configs, clock-frequency breaks booting because of_serial doesn't consume the gate_clk when clock-frequency is defined. The end result on kirkwood is that runit gets gated, and then the boot fails when the kernel tries to write to the serial port. Fix the issue by removing the clock-frequency parameter from all kirkwood dts files. Booted on dreamplug without earlyprintk and successfully logged in via ttyS0. Reported-by: Simon Baatz Tested-by: Simon Baatz Cc: Signed-off-by: Jason Cooper --- arch/arm/boot/dts/kirkwood-dns320.dts | 2 -- arch/arm/boot/dts/kirkwood-dns325.dts | 1 - arch/arm/boot/dts/kirkwood-dockstar.dts | 1 - arch/arm/boot/dts/kirkwood-dreamplug.dts | 1 - arch/arm/boot/dts/kirkwood-goflexnet.dts | 1 - arch/arm/boot/dts/kirkwood-ib62x0.dts | 1 - arch/arm/boot/dts/kirkwood-iconnect.dts | 1 - arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts | 1 - arch/arm/boot/dts/kirkwood-km_kirkwood.dts | 1 - arch/arm/boot/dts/kirkwood-lschlv2.dts | 1 - arch/arm/boot/dts/kirkwood-lsxhl.dts | 1 - arch/arm/boot/dts/kirkwood-mplcec4.dts | 1 - arch/arm/boot/dts/kirkwood-ns2-common.dtsi | 1 - arch/arm/boot/dts/kirkwood-nsa310.dts | 1 - arch/arm/boot/dts/kirkwood-openblocks_a6.dts | 2 -- arch/arm/boot/dts/kirkwood-topkick.dts | 1 - arch/arm/boot/dts/kirkwood.dtsi | 2 -- 17 files changed, 20 deletions(-) diff --git a/arch/arm/boot/dts/kirkwood-dns320.dts b/arch/arm/boot/dts/kirkwood-dns320.dts index 5bb0bf39d3b8..c9c44b2f62d7 100644 --- a/arch/arm/boot/dts/kirkwood-dns320.dts +++ b/arch/arm/boot/dts/kirkwood-dns320.dts @@ -42,12 +42,10 @@ ocp@f1000000 { serial@12000 { - clock-frequency = <166666667>; status = "okay"; }; serial@12100 { - clock-frequency = <166666667>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/kirkwood-dns325.dts b/arch/arm/boot/dts/kirkwood-dns325.dts index d430713ea9b9..e4e4930dc5cf 100644 --- a/arch/arm/boot/dts/kirkwood-dns325.dts +++ b/arch/arm/boot/dts/kirkwood-dns325.dts @@ -50,7 +50,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/kirkwood-dockstar.dts b/arch/arm/boot/dts/kirkwood-dockstar.dts index 2e3dd34e21a5..0196cf6b0ef2 100644 --- a/arch/arm/boot/dts/kirkwood-dockstar.dts +++ b/arch/arm/boot/dts/kirkwood-dockstar.dts @@ -37,7 +37,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-dreamplug.dts b/arch/arm/boot/dts/kirkwood-dreamplug.dts index ef2d8c705709..289e51d86372 100644 --- a/arch/arm/boot/dts/kirkwood-dreamplug.dts +++ b/arch/arm/boot/dts/kirkwood-dreamplug.dts @@ -38,7 +38,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-goflexnet.dts b/arch/arm/boot/dts/kirkwood-goflexnet.dts index 1b133e0c566e..bd83b8fc7c83 100644 --- a/arch/arm/boot/dts/kirkwood-goflexnet.dts +++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts @@ -73,7 +73,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-ib62x0.dts b/arch/arm/boot/dts/kirkwood-ib62x0.dts index 71902da33d63..5335b1aa8601 100644 --- a/arch/arm/boot/dts/kirkwood-ib62x0.dts +++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts @@ -51,7 +51,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "okay"; }; diff --git a/arch/arm/boot/dts/kirkwood-iconnect.dts b/arch/arm/boot/dts/kirkwood-iconnect.dts index 504f16be8b54..12ccf74ac3c4 100644 --- a/arch/arm/boot/dts/kirkwood-iconnect.dts +++ b/arch/arm/boot/dts/kirkwood-iconnect.dts @@ -78,7 +78,6 @@ }; }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts index 6cae4599c4b3..93c3afbef9ee 100644 --- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts +++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts @@ -115,7 +115,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts index 8db3123ac80f..5bbd0542cdd3 100644 --- a/arch/arm/boot/dts/kirkwood-km_kirkwood.dts +++ b/arch/arm/boot/dts/kirkwood-km_kirkwood.dts @@ -34,7 +34,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-lschlv2.dts b/arch/arm/boot/dts/kirkwood-lschlv2.dts index 9510c9ea666c..9f55d95f35f5 100644 --- a/arch/arm/boot/dts/kirkwood-lschlv2.dts +++ b/arch/arm/boot/dts/kirkwood-lschlv2.dts @@ -13,7 +13,6 @@ ocp@f1000000 { serial@12000 { - clock-frequency = <166666667>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/kirkwood-lsxhl.dts b/arch/arm/boot/dts/kirkwood-lsxhl.dts index 739019c4cba9..5c84c118ed8d 100644 --- a/arch/arm/boot/dts/kirkwood-lsxhl.dts +++ b/arch/arm/boot/dts/kirkwood-lsxhl.dts @@ -13,7 +13,6 @@ ocp@f1000000 { serial@12000 { - clock-frequency = <200000000>; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/kirkwood-mplcec4.dts b/arch/arm/boot/dts/kirkwood-mplcec4.dts index 662dfd81b1ce..758824118a9a 100644 --- a/arch/arm/boot/dts/kirkwood-mplcec4.dts +++ b/arch/arm/boot/dts/kirkwood-mplcec4.dts @@ -90,7 +90,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi index e8e7ecef1650..6affd924fe11 100644 --- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi +++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi @@ -23,7 +23,6 @@ }; serial@12000 { - clock-frequency = <166666667>; status = "okay"; }; diff --git a/arch/arm/boot/dts/kirkwood-nsa310.dts b/arch/arm/boot/dts/kirkwood-nsa310.dts index 3a178cf708d7..a7412b937a8a 100644 --- a/arch/arm/boot/dts/kirkwood-nsa310.dts +++ b/arch/arm/boot/dts/kirkwood-nsa310.dts @@ -117,7 +117,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts index ede7fe0d7a87..d27f7245f8e7 100644 --- a/arch/arm/boot/dts/kirkwood-openblocks_a6.dts +++ b/arch/arm/boot/dts/kirkwood-openblocks_a6.dts @@ -18,12 +18,10 @@ ocp@f1000000 { serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; serial@12100 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood-topkick.dts b/arch/arm/boot/dts/kirkwood-topkick.dts index 842ff95d60df..66eb45b00b25 100644 --- a/arch/arm/boot/dts/kirkwood-topkick.dts +++ b/arch/arm/boot/dts/kirkwood-topkick.dts @@ -108,7 +108,6 @@ }; serial@12000 { - clock-frequency = <200000000>; status = "ok"; }; diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index 2c738d9dc82a..19709fbe12cf 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -57,7 +57,6 @@ reg-shift = <2>; interrupts = <33>; clocks = <&gate_clk 7>; - /* set clock-frequency in board dts */ status = "disabled"; }; @@ -67,7 +66,6 @@ reg-shift = <2>; interrupts = <34>; clocks = <&gate_clk 7>; - /* set clock-frequency in board dts */ status = "disabled"; }; From 7bf5b408b419fc849578e6e9fbd221bf43638eb6 Mon Sep 17 00:00:00 2001 From: Sebastian Hesselbarth Date: Wed, 30 Jan 2013 21:29:58 +0100 Subject: [PATCH 23/37] ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels The ethernet controller used on kirkwood looses its MAC address register contents when the corresponding clock is gated. As soon as mv643xx_eth is built as module, the clock gets gated and when loading the module, the MAC address is gone. Proper DT support for the mv643xx_eth driver is expected soon, so we add a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround is also already used on non-DT kirkwood kernels. Reported-by: Simon Baatz Signed-off-by: Sebastian Hesselbarth Tested-by: Simon Baatz Cc: Signed-off-by: Jason Cooper --- arch/arm/mach-kirkwood/board-dt.c | 25 ++++++++++++++++++------- 1 file changed, 18 insertions(+), 7 deletions(-) diff --git a/arch/arm/mach-kirkwood/board-dt.c b/arch/arm/mach-kirkwood/board-dt.c index 2e73e9d53f70..d367aa6b47bb 100644 --- a/arch/arm/mach-kirkwood/board-dt.c +++ b/arch/arm/mach-kirkwood/board-dt.c @@ -41,16 +41,12 @@ static void __init kirkwood_legacy_clk_init(void) struct device_node *np = of_find_compatible_node( NULL, NULL, "marvell,kirkwood-gating-clock"); - struct of_phandle_args clkspec; + struct clk *clk; clkspec.np = np; clkspec.args_count = 1; - clkspec.args[0] = CGC_BIT_GE0; - orion_clkdev_add(NULL, "mv643xx_eth_port.0", - of_clk_get_from_provider(&clkspec)); - clkspec.args[0] = CGC_BIT_PEX0; orion_clkdev_add("0", "pcie", of_clk_get_from_provider(&clkspec)); @@ -59,9 +55,24 @@ static void __init kirkwood_legacy_clk_init(void) orion_clkdev_add("1", "pcie", of_clk_get_from_provider(&clkspec)); - clkspec.args[0] = CGC_BIT_GE1; - orion_clkdev_add(NULL, "mv643xx_eth_port.1", + clkspec.args[0] = CGC_BIT_SDIO; + orion_clkdev_add(NULL, "mvsdio", of_clk_get_from_provider(&clkspec)); + + /* + * The ethernet interfaces forget the MAC address assigned by + * u-boot if the clocks are turned off. Until proper DT support + * is available we always enable them for now. + */ + clkspec.args[0] = CGC_BIT_GE0; + clk = of_clk_get_from_provider(&clkspec); + orion_clkdev_add(NULL, "mv643xx_eth_port.0", clk); + clk_prepare_enable(clk); + + clkspec.args[0] = CGC_BIT_GE1; + clk = of_clk_get_from_provider(&clkspec); + orion_clkdev_add(NULL, "mv643xx_eth_port.1", clk); + clk_prepare_enable(clk); } static void __init kirkwood_of_clk_init(void) From de88747f514a4e0cca416a8871de2302f4f77790 Mon Sep 17 00:00:00 2001 From: Andrew Lunn Date: Sun, 3 Feb 2013 11:34:26 +0100 Subject: [PATCH 24/37] gpio: mvebu: Add clk support to prevent lockup The kirkwood SoC GPIO cores use the runit clock. Add code to clk_prepare_enable() runit, otherwise there is a danger of locking up the SoC by accessing the GPIO registers when runit clock is not ticking. Reported-by: Simon Baatz Signed-off-by: Andrew Lunn Tested-by: Simon Baatz Acked-by: Linus Walleij Cc: Signed-off-by: Jason Cooper --- arch/arm/boot/dts/kirkwood.dtsi | 2 ++ drivers/gpio/gpio-mvebu.c | 7 +++++++ 2 files changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index 19709fbe12cf..cf8e8926a034 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -38,6 +38,7 @@ interrupt-controller; #interrupt-cells = <2>; interrupts = <35>, <36>, <37>, <38>; + clocks = <&gate_clk 7>; }; gpio1: gpio@10140 { @@ -49,6 +50,7 @@ interrupt-controller; #interrupt-cells = <2>; interrupts = <39>, <40>, <41>; + clocks = <&gate_clk 7>; }; serial@12000 { diff --git a/drivers/gpio/gpio-mvebu.c b/drivers/gpio/gpio-mvebu.c index 7472182967ce..61a6fde6c089 100644 --- a/drivers/gpio/gpio-mvebu.c +++ b/drivers/gpio/gpio-mvebu.c @@ -42,6 +42,7 @@ #include #include #include +#include #include /* @@ -496,6 +497,7 @@ static int mvebu_gpio_probe(struct platform_device *pdev) struct resource *res; struct irq_chip_generic *gc; struct irq_chip_type *ct; + struct clk *clk; unsigned int ngpios; int soc_variant; int i, cpu, id; @@ -529,6 +531,11 @@ static int mvebu_gpio_probe(struct platform_device *pdev) return id; } + clk = devm_clk_get(&pdev->dev, NULL); + /* Not all SoCs require a clock.*/ + if (!IS_ERR(clk)) + clk_prepare_enable(clk); + mvchip->soc_variant = soc_variant; mvchip->chip.label = dev_name(&pdev->dev); mvchip->chip.dev = &pdev->dev; From 89c58c198b252f2bc20657fdd72a2aea788c435c Mon Sep 17 00:00:00 2001 From: Andrew Lunn Date: Sun, 3 Feb 2013 12:32:06 +0100 Subject: [PATCH 25/37] rtc: rtc-mv: Add support for clk to avoid lockups The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the driver clk_prepare_enable() this clock, otherwise there is a danger the SoC will lockup when accessing RTC registers with the clock disabled. Reported-by: Simon Baatz Signed-off-by: Andrew Lunn Tested-by: Simon Baatz Cc: Signed-off-by: Jason Cooper --- arch/arm/boot/dts/kirkwood.dtsi | 1 + drivers/rtc/rtc-mv.c | 28 ++++++++++++++++++++++++---- 2 files changed, 25 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index cf8e8926a034..fada7e6d24d8 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -75,6 +75,7 @@ compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc"; reg = <0x10300 0x20>; interrupts = <53>; + clocks = <&gate_clk 7>; }; spi@10600 { diff --git a/drivers/rtc/rtc-mv.c b/drivers/rtc/rtc-mv.c index 57233c885998..8f87fec27ce7 100644 --- a/drivers/rtc/rtc-mv.c +++ b/drivers/rtc/rtc-mv.c @@ -14,6 +14,7 @@ #include #include #include +#include #include #include @@ -41,6 +42,7 @@ struct rtc_plat_data { struct rtc_device *rtc; void __iomem *ioaddr; int irq; + struct clk *clk; }; static int mv_rtc_set_time(struct device *dev, struct rtc_time *tm) @@ -221,6 +223,7 @@ static int mv_rtc_probe(struct platform_device *pdev) struct rtc_plat_data *pdata; resource_size_t size; u32 rtc_time; + int ret = 0; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!res) @@ -239,11 +242,17 @@ static int mv_rtc_probe(struct platform_device *pdev) if (!pdata->ioaddr) return -ENOMEM; + pdata->clk = devm_clk_get(&pdev->dev, NULL); + /* Not all SoCs require a clock.*/ + if (!IS_ERR(pdata->clk)) + clk_prepare_enable(pdata->clk); + /* make sure the 24 hours mode is enabled */ rtc_time = readl(pdata->ioaddr + RTC_TIME_REG_OFFS); if (rtc_time & RTC_HOURS_12H_MODE) { dev_err(&pdev->dev, "24 Hours mode not supported.\n"); - return -EINVAL; + ret = -EINVAL; + goto out; } /* make sure it is actually functional */ @@ -252,7 +261,8 @@ static int mv_rtc_probe(struct platform_device *pdev) rtc_time = readl(pdata->ioaddr + RTC_TIME_REG_OFFS); if (rtc_time == 0x01000000) { dev_err(&pdev->dev, "internal RTC not ticking\n"); - return -ENODEV; + ret = -ENODEV; + goto out; } } @@ -268,8 +278,10 @@ static int mv_rtc_probe(struct platform_device *pdev) } else pdata->rtc = rtc_device_register(pdev->name, &pdev->dev, &mv_rtc_ops, THIS_MODULE); - if (IS_ERR(pdata->rtc)) - return PTR_ERR(pdata->rtc); + if (IS_ERR(pdata->rtc)) { + ret = PTR_ERR(pdata->rtc); + goto out; + } if (pdata->irq >= 0) { writel(0, pdata->ioaddr + RTC_ALARM_INTERRUPT_MASK_REG_OFFS); @@ -282,6 +294,11 @@ static int mv_rtc_probe(struct platform_device *pdev) } return 0; +out: + if (!IS_ERR(pdata->clk)) + clk_disable_unprepare(pdata->clk); + + return ret; } static int __exit mv_rtc_remove(struct platform_device *pdev) @@ -292,6 +309,9 @@ static int __exit mv_rtc_remove(struct platform_device *pdev) device_init_wakeup(&pdev->dev, 0); rtc_device_unregister(pdata->rtc); + if (!IS_ERR(pdata->clk)) + clk_disable_unprepare(pdata->clk); + return 0; } From f3ae1ae901d05b26d42e7f9cb3b2fb45ee478511 Mon Sep 17 00:00:00 2001 From: Paul Bolle Date: Tue, 5 Mar 2013 21:17:17 +0100 Subject: [PATCH 26/37] ARM: dove: drop "select COMMON_CLK_DOVE" Commit 5b03df9ace680d7cdd34a69dfd85ca5f74159d18 ("ARM: dove: switch to DT clock providers") added "select COMMON_CLK_DOVE" to Marvell Dove's Kconfig entry. But there's no Kconfig symbol COMMON_CLK_DOVE, which makes this select statement a nop. It's probably a leftover of some experimental code that never hit mainline. Drop it. Signed-off-by: Paul Bolle Signed-off-by: Jason Cooper --- arch/arm/Kconfig | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 5b714695b01b..0c990b75082f 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -556,7 +556,6 @@ config ARCH_IXP4XX config ARCH_DOVE bool "Marvell Dove" select ARCH_REQUIRE_GPIOLIB - select COMMON_CLK_DOVE select CPU_V7 select GENERIC_CLOCKEVENTS select MIGHT_HAVE_PCI From e822f75d848e29a034da7d238a9d5325cff1e9fe Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Tue, 5 Mar 2013 10:55:04 +0100 Subject: [PATCH 27/37] arm: mvebu: enable the USB ports on Armada 370 Reference Design board This patch modifies the Armada 370 Reference Design DTS file to enable support for the two USB ports found on this board. Signed-off-by: Florian Fainelli Signed-off-by: Jason Cooper --- arch/arm/boot/dts/armada-370-rd.dts | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts index f8e4855bc9a5..070bba4f2585 100644 --- a/arch/arm/boot/dts/armada-370-rd.dts +++ b/arch/arm/boot/dts/armada-370-rd.dts @@ -64,5 +64,13 @@ status = "okay"; /* No CD or WP GPIOs */ }; + + usb@d0050000 { + status = "okay"; + }; + + usb@d0051000 { + status = "okay"; + }; }; }; From 85c0c13dcdbb2d7cb375e6ace711e3655dd7a4dd Mon Sep 17 00:00:00 2001 From: Jean-Francois Moine Date: Fri, 8 Mar 2013 12:13:17 +0100 Subject: [PATCH 28/37] ARM: Dove: add RTC device node MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The commit: 48be9ac ARM: Dove: split legacy and DT setup removed the RTC initialization. This patch re-enables the RTC via the DT. Signed-off-by: Jean-François Moine Signed-off-by: Jason Cooper --- arch/arm/boot/dts/dove.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index 67dbe20868a2..f7509cafc377 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -197,6 +197,11 @@ status = "disabled"; }; + rtc@d8500 { + compatible = "marvell,orion-rtc"; + reg = <0xd8500 0x20>; + }; + crypto: crypto@30000 { compatible = "marvell,orion-crypto"; reg = <0x30000 0x10000>, From e366154f70c54dee3665d1c0f780007e514412f3 Mon Sep 17 00:00:00 2001 From: Heikki Krogerus Date: Wed, 6 Mar 2013 11:23:33 +0100 Subject: [PATCH 29/37] arm: mvebu: Reduce reg-io-width with UARTs Setting the reg-io-width to 1 byte represents more accurate description of the HW. This will fix an issue where UART driver causes kernel panic during bootup. Gregory CLEMENT traced the issue to autoconfig() in 8250.c, where the existence of FIFO is checked from UART_IIR register. The register is now read as 32-bit value as the reg-io-width is set to 4-bytes. The retuned value seems to contain bogus data for bits 31:8, causing the issue. Signed-off-by: Heikki Krogerus Cc: Gregory CLEMENT Cc: Masami Hiramatsu Tested-by: Gregory CLEMENT Acked-by: Gregory CLEMENT Tested-by: Masami Hiramatsu Tested-by: Thomas Petazzoni Signed-off-by: Jason Cooper --- arch/arm/boot/dts/armada-370-xp.dtsi | 4 ++-- arch/arm/boot/dts/armada-xp.dtsi | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 6f1acc75e155..99afca46e33d 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -54,7 +54,7 @@ reg = <0xd0012000 0x100>; reg-shift = <2>; interrupts = <41>; - reg-io-width = <4>; + reg-io-width = <1>; status = "disabled"; }; serial@d0012100 { @@ -62,7 +62,7 @@ reg = <0xd0012100 0x100>; reg-shift = <2>; interrupts = <42>; - reg-io-width = <4>; + reg-io-width = <1>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi index 1443949c165e..ca00d8326c87 100644 --- a/arch/arm/boot/dts/armada-xp.dtsi +++ b/arch/arm/boot/dts/armada-xp.dtsi @@ -46,7 +46,7 @@ reg = <0xd0012200 0x100>; reg-shift = <2>; interrupts = <43>; - reg-io-width = <4>; + reg-io-width = <1>; status = "disabled"; }; serial@d0012300 { @@ -54,7 +54,7 @@ reg = <0xd0012300 0x100>; reg-shift = <2>; interrupts = <44>; - reg-io-width = <4>; + reg-io-width = <1>; status = "disabled"; }; From 217bef3d37a9180bebd1953dffb6f9a3c77c557f Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Wed, 6 Mar 2013 11:23:34 +0100 Subject: [PATCH 30/37] arm: plat-orion: fix address decoding when > 4GB is used During the system initialization, the orion_setup_cpu_mbus_target() function reads the SDRAM address decoding registers to find out how many chip-selects of SDRAM have been enabled, and builds a small array with one entry per chip-select. This array is then used by device drivers (XOR, Ethernet, etc.) to configure their own address decoding windows to the SDRAM. However, devices can only access the first 32 bits of the physical memory. Even though LPAE is not supported for now, some Marvell boards are now showing up with 8 GB of RAM, configured using two SDRAM address decoding windows: the first covering the first 4 GB, the second covering the last 4 GB. The array built by orion_setup_cpu_mbus_target() has therefore two entries, and device drivers try to set up two address decoding windows to the SDRAM. However, in the device registers for the address decoding, the base address is only 32 bits, so those two windows overlap each other, and the devices do not work at all. This patch makes sure that the array built by orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows that correspond to the first 4 GB of the memory. To do that, it ignores the SDRAM decoding windows for which the 4 low-order bits are not zero (the 4 low-order bits of the base register are used to store bits 32:35 of the base address, so they actually indicate whether the base address is above 4 GB). This patch allows the newly introduced armada-xp-gp board to properly operate when it is mounted with more than 4 GB of RAM. Without that, all devices doing DMA (for example XOR and Ethernet) do not work at all. Signed-off-by: Thomas Petazzoni Tested-by: Ezequiel Garcia Signed-off-by: Jason Cooper --- arch/arm/plat-orion/addr-map.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/arch/arm/plat-orion/addr-map.c b/arch/arm/plat-orion/addr-map.c index febe3862873c..807ac8e5cbc0 100644 --- a/arch/arm/plat-orion/addr-map.c +++ b/arch/arm/plat-orion/addr-map.c @@ -157,9 +157,12 @@ void __init orion_setup_cpu_mbus_target(const struct orion_addr_map_cfg *cfg, u32 size = readl(ddr_window_cpu_base + DDR_SIZE_CS_OFF(i)); /* - * Chip select enabled? + * We only take care of entries for which the chip + * select is enabled, and that don't have high base + * address bits set (devices can only access the first + * 32 bits of the memory). */ - if (size & 1) { + if ((size & 1) && !(base & 0xF)) { struct mbus_dram_window *w; w = &orion_mbus_dram_info.cs[cs++]; From 1b72b78fda0433a7e115bc2d78603fde65fae0e7 Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Wed, 6 Mar 2013 11:23:35 +0100 Subject: [PATCH 31/37] arm: mvebu: fix address-cells in mpic DT node There is no need to have a #address-cells property in the MPIC Device Tree node, and more than that, having it confuses the of_irq_map_raw() logic, which will be used by the Marvell PCIe driver. Signed-off-by: Thomas Petazzoni Signed-off-by: Jason Cooper --- arch/arm/boot/dts/armada-370-xp.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 99afca46e33d..5b708208b607 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -31,7 +31,6 @@ mpic: interrupt-controller@d0020000 { compatible = "marvell,mpic"; #interrupt-cells = <1>; - #address-cells = <1>; #size-cells = <1>; interrupt-controller; }; From b2d57222b0f0963258a47da0ea7f0ec451c64712 Mon Sep 17 00:00:00 2001 From: Thomas Petazzoni Date: Wed, 6 Mar 2013 11:23:36 +0100 Subject: [PATCH 32/37] arm: mach-orion5x: fix typo in compatible string of a .dts file The orion5x-lacie-ethernet-disk-mini-v2.dts file was using "marvell-orion5x-88f5182" as a compatible string, while it should have been "marvell,orion5x-88f5182". Signed-off-by: Thomas Petazzoni Signed-off-by: Jason Cooper --- arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts index 5a3a58b7e18f..0077fc8510b7 100644 --- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts +++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts @@ -11,7 +11,7 @@ / { model = "LaCie Ethernet Disk mini V2"; - compatible = "lacie,ethernet-disk-mini-v2", "marvell-orion5x-88f5182", "marvell,orion5x"; + compatible = "lacie,ethernet-disk-mini-v2", "marvell,orion5x-88f5182", "marvell,orion5x"; memory { reg = <0x00000000 0x4000000>; /* 64 MB */ From 395816623d4f99b77fd53d6a537906ce25a08768 Mon Sep 17 00:00:00 2001 From: Shawn Guo Date: Mon, 11 Mar 2013 10:44:40 +0800 Subject: [PATCH 33/37] ARM: imx: pll1_sys should be an initial on clk We always boot from PLL1, so let's have pll1_sys in the clks_init_on list to have clk prepare/enable use count match the hardware status, so that drivers managing pll1_sys like cpufreq can get the use count right from the start. Reported-by: Dirk Behme Signed-off-by: Shawn Guo --- arch/arm/mach-imx/clk-imx6q.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c index 7b025ee528a5..2f9ff93a4e61 100644 --- a/arch/arm/mach-imx/clk-imx6q.c +++ b/arch/arm/mach-imx/clk-imx6q.c @@ -172,7 +172,7 @@ static struct clk *clk[clk_max]; static struct clk_onecell_data clk_data; static enum mx6q_clks const clks_init_on[] __initconst = { - mmdc_ch0_axi, rom, + mmdc_ch0_axi, rom, pll1_sys, }; static struct clk_div_table clk_enet_ref_table[] = { From 0c52db7e681678f9b2a3fb96c3dd557168b4e025 Mon Sep 17 00:00:00 2001 From: Paul Bolle Date: Mon, 11 Mar 2013 14:16:00 +0100 Subject: [PATCH 34/37] ARM: imx: fix typo "DEBUG_IMX50_IMX53_UART" Commit f8c95fe (ARM: imx: support DEBUG_LL uart port selection for all i.MX SoCs) had a typo that DEBUG_IMX50_IMX53_UART should be DEBUG_IMX53_UART. Signed-off-by: Paul Bolle Signed-off-by: Shawn Guo --- arch/arm/Kconfig.debug | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index acddddac7ee4..ecfcdba2d17c 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -492,7 +492,7 @@ config DEBUG_IMX_UART_PORT DEBUG_IMX31_UART || \ DEBUG_IMX35_UART || \ DEBUG_IMX51_UART || \ - DEBUG_IMX50_IMX53_UART || \ + DEBUG_IMX53_UART || \ DEBUG_IMX6Q_UART default 1 help From 2a6ad871a10ce915a300d8f227168ad4c34936ec Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Sun, 3 Feb 2013 12:24:48 +0100 Subject: [PATCH 35/37] ARM: multiplatform: Sort the max gpio numbers. When building a multiplatform kernel, we could end up with a smaller number of GPIOs than the one required by the platform the kernel was running on. Sort the max GPIO number by descending order so that we always take the highest number required. Signed-off-by: Maxime Ripard Signed-off-by: Arnd Bergmann --- arch/arm/Kconfig | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 5b714695b01b..c7e027436f9e 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1657,13 +1657,16 @@ config LOCAL_TIMERS accounting to be spread across the timer interval, preventing a "thundering herd" at every timer tick. +# The GPIO number here must be sorted by descending number. In case of +# a multiplatform kernel, we just want the highest value required by the +# selected platforms. config ARCH_NR_GPIO int default 1024 if ARCH_SHMOBILE || ARCH_TEGRA - default 355 if ARCH_U8500 - default 264 if MACH_H4700 default 512 if SOC_OMAP5 + default 355 if ARCH_U8500 default 288 if ARCH_VT8500 || ARCH_SUNXI + default 264 if MACH_H4700 default 0 help Maximum number of GPIOs in the system. From 0d8abbfd96e6ebd0b97e0f740614cc5e62d94d84 Mon Sep 17 00:00:00 2001 From: Padmavathi Venna Date: Mon, 4 Mar 2013 11:04:28 +0530 Subject: [PATCH 36/37] Arm: socfpga: pl330: Add #dma-cells for generic dma binding support This patch adds #dma-cells property to PL330 DMA controller nodes for supporting generic dma dt bindings on SOCFPGA platform. #dma-channels and #dma-requests are not required now but added in advance. Signed-off-by: Padmavathi Venna Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/socfpga.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index 936d2306e7e1..7e8769bd5977 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -75,6 +75,9 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0xffe01000 0x1000>; interrupts = <0 180 4>; + #dma-cells = <1>; + #dma-channels = <8>; + #dma-requests = <32>; }; }; From 27f423fe120df3a7488dd750b4e0508f03c325b6 Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Sat, 2 Mar 2013 00:10:30 +0100 Subject: [PATCH 37/37] ARM: spear3xx: Use correct pl080 header file The definitions have move around recently, causing build errors in spear3xx for all configurations: spear3xx.c:47:5: error: 'PL080_BSIZE_16' undeclared here (not in a function) spear3xx.c:47:23: error: 'PL080_CONTROL_SB_SIZE_SHIFT' undeclared here (not in a function) spear3xx.c:48:22: error: 'PL080_CONTROL_DB_SIZE_SHIFT' undeclared here (not in a function) Signed-off-by: Arnd Bergmann Cc: Alessandro Rubini Cc: Viresh Kumar --- arch/arm/mach-spear3xx/spear3xx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/mach-spear3xx/spear3xx.c b/arch/arm/mach-spear3xx/spear3xx.c index f9d754f90c59..d2b3937c4014 100644 --- a/arch/arm/mach-spear3xx/spear3xx.c +++ b/arch/arm/mach-spear3xx/spear3xx.c @@ -14,7 +14,7 @@ #define pr_fmt(fmt) "SPEAr3xx: " fmt #include -#include +#include #include #include #include