ARM: dts: qcom: Remove Arrow SD600 eval board
This patch removes support for the APQ8064 based Arrow SD600 eval board. This board was never sold publicly and had very limited distribution. As such, we are removing this board and no longer going to support it. Signed-off-by: Andy Gross <andy.gross@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org> Acked-by: Olof Johansson <olof@lixom.net>
This commit is contained in:
Andy Gross
parent
28d13d317b
commit
972910948f
|
|
@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
|
|||
ox820-cloudengines-pogoplug-series-3.dtb
|
||||
dtb-$(CONFIG_ARCH_QCOM) += \
|
||||
qcom-apq8060-dragonboard.dtb \
|
||||
qcom-apq8064-arrow-sd-600eval.dtb \
|
||||
qcom-apq8064-cm-qs600.dtb \
|
||||
qcom-apq8064-ifc6410.dtb \
|
||||
qcom-apq8064-sony-xperia-yuga.dtb \
|
||||
|
|
|
|||
|
|
@ -1,53 +0,0 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
&tlmm_pinmux {
|
||||
card_detect: card-detect {
|
||||
mux {
|
||||
pins = "gpio26";
|
||||
function = "gpio";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
pcie_pins: pcie-pinmux {
|
||||
mux {
|
||||
pins = "gpio27";
|
||||
function = "gpio";
|
||||
};
|
||||
conf {
|
||||
pins = "gpio27";
|
||||
drive-strength = <12>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
user_leds: user-leds {
|
||||
mux {
|
||||
pins = "gpio3", "gpio7", "gpio10", "gpio11";
|
||||
function = "gpio";
|
||||
};
|
||||
|
||||
conf {
|
||||
pins = "gpio3", "gpio7", "gpio10", "gpio11";
|
||||
function = "gpio";
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
|
||||
magneto_pins: magneto-pins {
|
||||
mux {
|
||||
pins = "gpio31", "gpio48";
|
||||
function = "gpio";
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pm8921_mpps {
|
||||
mpp_leds: mpp-leds {
|
||||
pinconf {
|
||||
pins = "mpp7", "mpp8";
|
||||
function = "digital";
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
|
@ -1,415 +0,0 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
#include "qcom-apq8064-v2.0.dtsi"
|
||||
#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/mfd/qcom-rpm.h>
|
||||
|
||||
/ {
|
||||
model = "Arrow Electronics, APQ8064 SD_600eval";
|
||||
compatible = "arrow,sd_600eval", "qcom,apq8064";
|
||||
|
||||
aliases {
|
||||
serial0 = &gsbi7_serial;
|
||||
serial1 = &gsbi1_serial;
|
||||
i2c0 = &gsbi2_i2c;
|
||||
i2c1 = &gsbi3_i2c;
|
||||
i2c2 = &gsbi4_i2c;
|
||||
i2c3 = &gsbi7_i2c;
|
||||
spi0 = &gsbi5_spi;
|
||||
};
|
||||
|
||||
regulators {
|
||||
compatible = "simple-bus";
|
||||
vph: regulator-fixed@1 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-min-microvolt = <4500000>;
|
||||
regulator-max-microvolt = <4500000>;
|
||||
regulator-name = "VPH";
|
||||
regulator-type = "voltage";
|
||||
regulator-boot-on;
|
||||
};
|
||||
|
||||
/* on board fixed 3.3v supply */
|
||||
vcc3v3: vcc3v3 {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "VCC3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
};
|
||||
|
||||
hdmi-out {
|
||||
compatible = "hdmi-connector";
|
||||
type = "a";
|
||||
|
||||
port {
|
||||
hdmi_con: endpoint {
|
||||
remote-endpoint = <&hdmi_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
soc {
|
||||
rpm@108000 {
|
||||
regulators {
|
||||
vdd_s1-supply = <&vph>;
|
||||
vdd_s2-supply = <&vph>;
|
||||
vdd_s3-supply = <&vph>;
|
||||
vdd_s4-supply = <&vph>;
|
||||
vdd_s5-supply = <&vph>;
|
||||
vdd_s6-supply = <&vph>;
|
||||
vdd_s7-supply = <&vph>;
|
||||
vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
|
||||
vdd_l3_l15_l17-supply = <&vph>;
|
||||
vdd_l4_l14-supply = <&vph>;
|
||||
vdd_l5_l8_l16-supply = <&vph>;
|
||||
vdd_l6_l7-supply = <&vph>;
|
||||
vdd_l9_l11-supply = <&vph>;
|
||||
vdd_l10_l22-supply = <&vph>;
|
||||
vdd_l21_l23_l29-supply = <&vph>;
|
||||
vdd_l24-supply = <&pm8921_s1>;
|
||||
vdd_l25-supply = <&pm8921_s1>;
|
||||
vdd_l26-supply = <&pm8921_s7>;
|
||||
vdd_l27-supply = <&pm8921_s7>;
|
||||
vdd_l28-supply = <&pm8921_s7>;
|
||||
vin_lvs1_3_6-supply = <&pm8921_s4>;
|
||||
vin_lvs2-supply = <&pm8921_s1>;
|
||||
vin_lvs4_5_7-supply = <&pm8921_s4>;
|
||||
|
||||
s1 {
|
||||
regulator-always-on;
|
||||
regulator-min-microvolt = <1225000>;
|
||||
regulator-max-microvolt = <1225000>;
|
||||
qcom,switch-mode-frequency = <3200000>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
s2 {
|
||||
regulator-min-microvolt = <1300000>;
|
||||
regulator-max-microvolt = <1300000>;
|
||||
qcom,switch-mode-frequency = <1600000>;
|
||||
bias-pull-down;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
s3 {
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1400000>;
|
||||
qcom,switch-mode-frequency = <4800000>;
|
||||
};
|
||||
|
||||
s4 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
qcom,switch-mode-frequency = <1600000>;
|
||||
qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
|
||||
bias-pull-down;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
s7 {
|
||||
regulator-min-microvolt = <1300000>;
|
||||
regulator-max-microvolt = <1300000>;
|
||||
qcom,switch-mode-frequency = <3200000>;
|
||||
};
|
||||
|
||||
l3 {
|
||||
regulator-min-microvolt = <3050000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
l4 {
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
l5 {
|
||||
regulator-min-microvolt = <2750000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
bias-pull-down;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
l6 {
|
||||
regulator-min-microvolt = <2950000>;
|
||||
regulator-max-microvolt = <2950000>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
/**
|
||||
* 1.8v required on LS expansion
|
||||
* for mezzanine boards
|
||||
*/
|
||||
l15 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <1800000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
l23 {
|
||||
regulator-min-microvolt = <1700000>;
|
||||
regulator-max-microvolt = <1900000>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
lvs6 {
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
lvs7 {
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gsbi@12440000 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_UART_W_FC>;
|
||||
serial@12450000 {
|
||||
label = "LS-UART1";
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gsbi1_uart_4pins>;
|
||||
};
|
||||
};
|
||||
|
||||
gsbi@12480000 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_I2C>;
|
||||
i2c@124a0000 {
|
||||
/* On Low speed expansion and Sensors */
|
||||
label = "LS-I2C0";
|
||||
status = "okay";
|
||||
lis3mdl_mag@1e {
|
||||
compatible = "st,lis3mdl-magn";
|
||||
reg = <0x1e>;
|
||||
vdd-supply = <&vcc3v3>;
|
||||
vddio-supply = <&pm8921_s4>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&magneto_pins>;
|
||||
interrupt-parent = <&tlmm_pinmux>;
|
||||
|
||||
st,drdy-int-pin = <2>;
|
||||
interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
|
||||
<31 IRQ_TYPE_EDGE_RISING>; /* INT */
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gsbi@16200000 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_I2C>;
|
||||
i2c@16280000 {
|
||||
/* On Low speed expansion */
|
||||
status = "okay";
|
||||
label = "LS-I2C1";
|
||||
clock-frequency = <200000>;
|
||||
eeprom@52 {
|
||||
compatible = "atmel,24c128";
|
||||
reg = <0x52>;
|
||||
pagesize = <64>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
gsbi@16300000 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_I2C>;
|
||||
i2c@16380000 {
|
||||
/* On High speed expansion */
|
||||
label = "HS-CAM-I2C3";
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
gsbi@1a200000 {
|
||||
status = "okay";
|
||||
spi@1a280000 {
|
||||
/* On Low speed expansion */
|
||||
label = "LS-SPI0";
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
/* DEBUG UART */
|
||||
gsbi@16600000 {
|
||||
status = "okay";
|
||||
qcom,mode = <GSBI_PROT_I2C_UART>;
|
||||
serial@16640000 {
|
||||
label = "LS-UART0";
|
||||
status = "okay";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&gsbi7_uart_2pins>;
|
||||
};
|
||||
|
||||
i2c@16680000 {
|
||||
/* On High speed expansion */
|
||||
status = "okay";
|
||||
label = "HS-CAM-I2C2";
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&user_leds>, <&mpp_leds>;
|
||||
|
||||
compatible = "gpio-leds";
|
||||
|
||||
user-led0 {
|
||||
label = "user0-led";
|
||||
gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
user-led1 {
|
||||
label = "user1-led";
|
||||
gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "mmc0";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
user-led2 {
|
||||
label = "user2-led";
|
||||
gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "mmc1";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
user-led3 {
|
||||
label = "user3-led";
|
||||
gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "none";
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
wifi-led {
|
||||
label = "WiFi-led";
|
||||
gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "off";
|
||||
};
|
||||
|
||||
bt-led {
|
||||
label = "BT-led";
|
||||
gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
|
||||
default-state = "off";
|
||||
};
|
||||
};
|
||||
|
||||
pci@1b500000 {
|
||||
status = "okay";
|
||||
vdda-supply = <&pm8921_s3>;
|
||||
vdda_phy-supply = <&pm8921_lvs6>;
|
||||
vdda_refclk-supply = <&vcc3v3>;
|
||||
pinctrl-0 = <&pcie_pins>;
|
||||
pinctrl-names = "default";
|
||||
perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
phy@1b400000 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
sata@29000000 {
|
||||
status = "okay";
|
||||
target-supply = <&pm8921_lvs7>;
|
||||
};
|
||||
|
||||
/* OTG */
|
||||
usb@12500000 {
|
||||
status = "okay";
|
||||
dr_mode = "peripheral";
|
||||
ulpi {
|
||||
phy {
|
||||
v3p3-supply = <&pm8921_l3>;
|
||||
v1p8-supply = <&pm8921_l4>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb@12520000 {
|
||||
status = "okay";
|
||||
dr_mode = "otg";
|
||||
ulpi {
|
||||
phy {
|
||||
v3p3-supply = <&pm8921_l3>;
|
||||
v1p8-supply = <&pm8921_l23>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
usb@12530000 {
|
||||
status = "okay";
|
||||
dr_mode = "otg";
|
||||
ulpi {
|
||||
phy {
|
||||
v3p3-supply = <&pm8921_l3>;
|
||||
v1p8-supply = <&pm8921_l23>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
amba {
|
||||
/* eMMC */
|
||||
sdcc@12400000 {
|
||||
status = "okay";
|
||||
vmmc-supply = <&pm8921_l5>;
|
||||
vqmmc-supply = <&pm8921_s4>;
|
||||
};
|
||||
|
||||
/* External micro SD card */
|
||||
sdcc@12180000 {
|
||||
status = "okay";
|
||||
vmmc-supply = <&pm8921_l6>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&card_detect>;
|
||||
cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
riva-pil@3204000 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
|
||||
};
|
||||
|
||||
hdmi-tx@4a00000 {
|
||||
status = "okay";
|
||||
core-vdda-supply = <&pm8921_hdmi_switch>;
|
||||
hdmi-mux-supply = <&vcc3v3>;
|
||||
|
||||
hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
|
||||
|
||||
ports {
|
||||
port@1 {
|
||||
endpoint {
|
||||
remote-endpoint = <&hdmi_con>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
hdmi-phy@4a00400 {
|
||||
status = "okay";
|
||||
core-vdda-supply = <&pm8921_hdmi_switch>;
|
||||
};
|
||||
|
||||
mdp@5100000 {
|
||||
status = "okay";
|
||||
|
||||
ports {
|
||||
port@3 {
|
||||
endpoint {
|
||||
remote-endpoint = <&hdmi_in>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
Loading…
Reference in New Issue