OpenE2K
/
linux
6
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

ARM: shmobile: Koelsch: add Ether support 

Register Ether platform device and pin data on  the  Koelsch board.
Register platform fixup for Micrel KSZ8041 PHY, just like on the Lager board.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This commit is contained in:
Sergei Shtylyov 2013-12-08 23:52:44 +03:00 committed by Simon Horman
parent 784c33a0c9
commit 974faba705
1 changed files with 55 additions and 1 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

56
arch/arm/mach-shmobile/board-koelsch.c
View File

@ -25,10 +25,12 @@
#include <linux/input.h>
#include <linux/kernel.h>
#include <linux/leds.h>
#include <linux/phy.h>
#include <linux/pinctrl/machine.h>
#include <linux/platform_data/gpio-rcar.h>
#include <linux/platform_data/rcar-du.h>
#include <linux/platform_device.h>
#include <linux/sh_eth.h>
#include <mach/common.h>
#include <mach/irqs.h>
#include <mach/r8a7791.h>
@ -87,6 +89,19 @@ static void __init koelsch_add_du_device(void)
platform_device_register_full(&info);
}
/* Ether */
static const struct sh_eth_plat_data ether_pdata __initconst = {
.phy = 0x1,
.edmac_endian = EDMAC_LITTLE_ENDIAN,
.phy_interface = PHY_INTERFACE_MODE_RMII,
.ether_link_active_low = 1,
};
static const struct resource ether_resources[] __initconst = {
DEFINE_RES_MEM(0xee700000, 0x400),
DEFINE_RES_IRQ(gic_spi(162)),
};
/* LEDS */
static struct gpio_led koelsch_leds[] = {
{
@ -141,6 +156,15 @@ static const struct pinctrl_map koelsch_pinctrl_map[] = {
"du_sync", "du"),
PIN_MAP_MUX_GROUP_DEFAULT("rcar-du-r8a7791", "pfc-r8a7791",
"du_clk_out_0", "du"),
/* Ether */
PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
"eth_link", "eth"),
PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
"eth_mdio", "eth"),
PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
"eth_rmii", "eth"),
PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
"intc_irq0", "intc"),
/* SCIF0 (CN19: DEBUG SERIAL0) */
PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7791",
"scif0_data_d", "scif0"),
@ -156,6 +180,10 @@ static void __init koelsch_add_standard_devices(void)
ARRAY_SIZE(koelsch_pinctrl_map));
r8a7791_pinmux_init();
r8a7791_add_standard_devices();
platform_device_register_resndata(&platform_bus, "r8a7791-ether", -1,
ether_resources,
ARRAY_SIZE(ether_resources),
&ether_pdata, sizeof(ether_pdata));
platform_device_register_data(&platform_bus, "leds-gpio", -1,
&koelsch_leds_pdata,
sizeof(koelsch_leds_pdata));
@ -166,6 +194,32 @@ static void __init koelsch_add_standard_devices(void)
koelsch_add_du_device();
}
/*
* Ether LEDs on the Koelsch board are named LINK and ACTIVE which corresponds
* to non-default 01 setting of the Micrel KSZ8041 PHY control register 1 bits
* 14-15. We have to set them back to 01 from the default 00 value each time
* the PHY is reset. It's also important because the PHY's LED0 signal is
* connected to SoC's ETH_LINK signal and in the PHY's default mode it will
* bounce on and off after each packet, which we apparently want to avoid.
*/
static int koelsch_ksz8041_fixup(struct phy_device *phydev)
{
u16 phyctrl1 = phy_read(phydev, 0x1e);
phyctrl1 &= ~0xc000;
phyctrl1 |= 0x4000;
return phy_write(phydev, 0x1e, phyctrl1);
}
static void __init koelsch_init(void)
{
koelsch_add_standard_devices();
if (IS_ENABLED(CONFIG_PHYLIB))
phy_register_fixup_for_id("r8a7791-ether-ff:01",
koelsch_ksz8041_fixup);
}
static const char * const koelsch_boards_compat_dt[] __initconst = {
"renesas,koelsch",
NULL,
@ -175,7 +229,7 @@ DT_MACHINE_START(KOELSCH_DT, "koelsch")
.smp = smp_ops(r8a7791_smp_ops),
.init_early = r8a7791_init_early,
.init_time = rcar_gen2_timer_init,
.init_machine = koelsch_add_standard_devices,
.init_machine = koelsch_init,
.init_late = shmobile_init_late,
.dt_compat = koelsch_boards_compat_dt,
MACHINE_END