Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (lm85) extend to support EMC6D103 chips
  MAINTAINERS: Remove stale hwmon quilt tree
  hwmon: (k10temp) add support for AMD Family 12h/14h CPUs
  hwmon: (jc42) do not allow writing to locked registers
  hwmon: (jc42) more helpful documentation
  hwmon: (jc42) fix type mismatch
This commit is contained in:
Linus Torvalds 2011-02-20 10:15:22 -08:00
commit a0c85e96d3
7 changed files with 86 additions and 26 deletions

View File

@ -51,7 +51,8 @@ Supported chips:
* JEDEC JC 42.4 compliant temperature sensor chips
Prefix: 'jc42'
Addresses scanned: I2C 0x18 - 0x1f
Datasheet: -
Datasheet:
http://www.jedec.org/sites/default/files/docs/4_01_04R19.pdf
Author:
Guenter Roeck <guenter.roeck@ericsson.com>
@ -60,7 +61,11 @@ Author:
Description
-----------
This driver implements support for JEDEC JC 42.4 compliant temperature sensors.
This driver implements support for JEDEC JC 42.4 compliant temperature sensors,
which are used on many DDR3 memory modules for mobile devices and servers. Some
systems use the sensor to prevent memory overheating by automatically throttling
the memory controller.
The driver auto-detects the chips listed above, but can be manually instantiated
to support other JC 42.4 compliant chips.
@ -81,15 +86,19 @@ limits. The chip supports only a single register to configure the hysteresis,
which applies to all limits. This register can be written by writing into
temp1_crit_hyst. Other hysteresis attributes are read-only.
If the BIOS has configured the sensor for automatic temperature management, it
is likely that it has locked the registers, i.e., that the temperature limits
cannot be changed.
Sysfs entries
-------------
temp1_input Temperature (RO)
temp1_min Minimum temperature (RW)
temp1_max Maximum temperature (RW)
temp1_crit Critical high temperature (RW)
temp1_min Minimum temperature (RO or RW)
temp1_max Maximum temperature (RO or RW)
temp1_crit Critical high temperature (RO or RW)
temp1_crit_hyst Critical hysteresis temperature (RW)
temp1_crit_hyst Critical hysteresis temperature (RO or RW)
temp1_max_hyst Maximum hysteresis temperature (RO)
temp1_min_alarm Temperature low alarm

View File

@ -9,6 +9,8 @@ Supported chips:
Socket S1G3: Athlon II, Sempron, Turion II
* AMD Family 11h processors:
Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra)
* AMD Family 12h processors: "Llano"
* AMD Family 14h processors: "Brazos" (C/E/G-Series)
Prefix: 'k10temp'
Addresses scanned: PCI space
@ -17,10 +19,14 @@ Supported chips:
http://support.amd.com/us/Processor_TechDocs/31116.pdf
BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors:
http://support.amd.com/us/Processor_TechDocs/41256.pdf
BIOS and Kernel Developer's Guide (BKDG) for AMD Family 14h Models 00h-0Fh Processors:
http://support.amd.com/us/Processor_TechDocs/43170.pdf
Revision Guide for AMD Family 10h Processors:
http://support.amd.com/us/Processor_TechDocs/41322.pdf
Revision Guide for AMD Family 11h Processors:
http://support.amd.com/us/Processor_TechDocs/41788.pdf
Revision Guide for AMD Family 14h Models 00h-0Fh Processors:
http://support.amd.com/us/Processor_TechDocs/47534.pdf
AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks:
http://support.amd.com/us/Processor_TechDocs/43373.pdf
AMD Family 10h Server and Workstation Processor Power and Thermal Data Sheet:
@ -34,7 +40,7 @@ Description
-----------
This driver permits reading of the internal temperature sensor of AMD
Family 10h and 11h processors.
Family 10h/11h/12h/14h processors.
All these processors have a sensor, but on those for Socket F or AM2+,
the sensor may return inconsistent values (erratum 319). The driver

View File

@ -2873,7 +2873,6 @@ M: Guenter Roeck <guenter.roeck@ericsson.com>
L: lm-sensors@lm-sensors.org
W: http://www.lm-sensors.org/
T: quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-hwmon/
T: quilt kernel.org/pub/linux/kernel/people/groeck/linux-staging/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging.git
S: Maintained
F: Documentation/hwmon/

View File

@ -238,13 +238,13 @@ config SENSORS_K8TEMP
will be called k8temp.
config SENSORS_K10TEMP
tristate "AMD Phenom/Sempron/Turion/Opteron temperature sensor"
tristate "AMD Family 10h/11h/12h/14h temperature sensor"
depends on X86 && PCI
help
If you say yes here you get support for the temperature
sensor(s) inside your CPU. Supported are later revisions of
the AMD Family 10h and all revisions of the AMD Family 11h
microarchitectures.
the AMD Family 10h and all revisions of the AMD Family 11h,
12h (Llano), and 14h (Brazos) microarchitectures.
This driver can also be built as a module. If so, the module
will be called k10temp.
@ -455,13 +455,14 @@ config SENSORS_JZ4740
called jz4740-hwmon.
config SENSORS_JC42
tristate "JEDEC JC42.4 compliant temperature sensors"
tristate "JEDEC JC42.4 compliant memory module temperature sensors"
depends on I2C
help
If you say yes here you get support for Jedec JC42.4 compliant
temperature sensors. Support will include, but not be limited to,
ADT7408, CAT34TS02,, CAT6095, MAX6604, MCP9805, MCP98242, MCP98243,
MCP9843, SE97, SE98, STTS424, TSE2002B3, and TS3000B3.
If you say yes here, you get support for JEDEC JC42.4 compliant
temperature sensors, which are used on many DDR3 memory modules for
mobile devices and servers. Support will include, but not be limited
to, ADT7408, CAT34TS02, CAT6095, MAX6604, MCP9805, MCP98242, MCP98243,
MCP9843, SE97, SE98, STTS424(E), TSE2002B3, and TS3000B3.
This driver can also be built as a module. If so, the module
will be called jc42.
@ -574,7 +575,7 @@ config SENSORS_LM85
help
If you say yes here you get support for National Semiconductor LM85
sensor chips and clones: ADM1027, ADT7463, ADT7468, EMC6D100,
EMC6D101 and EMC6D102.
EMC6D101, EMC6D102, and EMC6D103.
This driver can also be built as a module. If so, the module
will be called lm85.

View File

@ -53,6 +53,8 @@ static const unsigned short normal_i2c[] = {
/* Configuration register defines */
#define JC42_CFG_CRIT_ONLY (1 << 2)
#define JC42_CFG_TCRIT_LOCK (1 << 6)
#define JC42_CFG_EVENT_LOCK (1 << 7)
#define JC42_CFG_SHUTDOWN (1 << 8)
#define JC42_CFG_HYST_SHIFT 9
#define JC42_CFG_HYST_MASK 0x03
@ -332,7 +334,7 @@ static ssize_t set_temp_crit_hyst(struct device *dev,
{
struct i2c_client *client = to_i2c_client(dev);
struct jc42_data *data = i2c_get_clientdata(client);
long val;
unsigned long val;
int diff, hyst;
int err;
int ret = count;
@ -380,14 +382,14 @@ static ssize_t show_alarm(struct device *dev,
static DEVICE_ATTR(temp1_input, S_IRUGO,
show_temp_input, NULL);
static DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO,
static DEVICE_ATTR(temp1_crit, S_IRUGO,
show_temp_crit, set_temp_crit);
static DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO,
static DEVICE_ATTR(temp1_min, S_IRUGO,
show_temp_min, set_temp_min);
static DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO,
static DEVICE_ATTR(temp1_max, S_IRUGO,
show_temp_max, set_temp_max);
static DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO,
static DEVICE_ATTR(temp1_crit_hyst, S_IRUGO,
show_temp_crit_hyst, set_temp_crit_hyst);
static DEVICE_ATTR(temp1_max_hyst, S_IRUGO,
show_temp_max_hyst, NULL);
@ -412,8 +414,31 @@ static struct attribute *jc42_attributes[] = {
NULL
};
static mode_t jc42_attribute_mode(struct kobject *kobj,
struct attribute *attr, int index)
{
struct device *dev = container_of(kobj, struct device, kobj);
struct i2c_client *client = to_i2c_client(dev);
struct jc42_data *data = i2c_get_clientdata(client);
unsigned int config = data->config;
bool readonly;
if (attr == &dev_attr_temp1_crit.attr)
readonly = config & JC42_CFG_TCRIT_LOCK;
else if (attr == &dev_attr_temp1_min.attr ||
attr == &dev_attr_temp1_max.attr)
readonly = config & JC42_CFG_EVENT_LOCK;
else if (attr == &dev_attr_temp1_crit_hyst.attr)
readonly = config & (JC42_CFG_EVENT_LOCK | JC42_CFG_TCRIT_LOCK);
else
readonly = true;
return S_IRUGO | (readonly ? 0 : S_IWUSR);
}
static const struct attribute_group jc42_group = {
.attrs = jc42_attributes,
.is_visible = jc42_attribute_mode,
};
/* Return 0 if detection is successful, -ENODEV otherwise */

View File

@ -1,5 +1,5 @@
/*
* k10temp.c - AMD Family 10h/11h processor hardware monitoring
* k10temp.c - AMD Family 10h/11h/12h/14h processor hardware monitoring
*
* Copyright (c) 2009 Clemens Ladisch <clemens@ladisch.de>
*
@ -25,7 +25,7 @@
#include <linux/pci.h>
#include <asm/processor.h>
MODULE_DESCRIPTION("AMD Family 10h/11h CPU core temperature monitor");
MODULE_DESCRIPTION("AMD Family 10h/11h/12h/14h CPU core temperature monitor");
MODULE_AUTHOR("Clemens Ladisch <clemens@ladisch.de>");
MODULE_LICENSE("GPL");
@ -208,6 +208,7 @@ static void __devexit k10temp_remove(struct pci_dev *pdev)
static const struct pci_device_id k10temp_id_table[] = {
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_10H_NB_MISC) },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_11H_NB_MISC) },
{ PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_CNB17H_F3) },
{}
};
MODULE_DEVICE_TABLE(pci, k10temp_id_table);

View File

@ -41,7 +41,7 @@ static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
enum chips {
any_chip, lm85b, lm85c,
adm1027, adt7463, adt7468,
emc6d100, emc6d102
emc6d100, emc6d102, emc6d103
};
/* The LM85 registers */
@ -90,6 +90,9 @@ enum chips {
#define LM85_VERSTEP_EMC6D100_A0 0x60
#define LM85_VERSTEP_EMC6D100_A1 0x61
#define LM85_VERSTEP_EMC6D102 0x65
#define LM85_VERSTEP_EMC6D103_A0 0x68
#define LM85_VERSTEP_EMC6D103_A1 0x69
#define LM85_VERSTEP_EMC6D103S 0x6A /* Also known as EMC6D103:A2 */
#define LM85_REG_CONFIG 0x40
@ -348,6 +351,7 @@ static const struct i2c_device_id lm85_id[] = {
{ "emc6d100", emc6d100 },
{ "emc6d101", emc6d100 },
{ "emc6d102", emc6d102 },
{ "emc6d103", emc6d103 },
{ }
};
MODULE_DEVICE_TABLE(i2c, lm85_id);
@ -1250,6 +1254,20 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info)
case LM85_VERSTEP_EMC6D102:
type_name = "emc6d102";
break;
case LM85_VERSTEP_EMC6D103_A0:
case LM85_VERSTEP_EMC6D103_A1:
type_name = "emc6d103";
break;
/*
* Registers apparently missing in EMC6D103S/EMC6D103:A2
* compared to EMC6D103:A0, EMC6D103:A1, and EMC6D102
* (according to the data sheets), but used unconditionally
* in the driver: 62[5:7], 6D[0:7], and 6E[0:7].
* So skip EMC6D103S for now.
case LM85_VERSTEP_EMC6D103S:
type_name = "emc6d103s";
break;
*/
}
} else {
dev_dbg(&adapter->dev,
@ -1283,6 +1301,7 @@ static int lm85_probe(struct i2c_client *client,
case adt7468:
case emc6d100:
case emc6d102:
case emc6d103:
data->freq_map = adm1027_freq_map;
break;
default:
@ -1468,7 +1487,7 @@ static struct lm85_data *lm85_update_device(struct device *dev)
/* More alarm bits */
data->alarms |= lm85_read_value(client,
EMC6D100_REG_ALARM3) << 16;
} else if (data->type == emc6d102) {
} else if (data->type == emc6d102 || data->type == emc6d103) {
/* Have to read LSB bits after the MSB ones because
the reading of the MSB bits has frozen the
LSBs (backward from the ADM1027).