From a62330176fd2a81ac6b07ed246e40419108422a7 Mon Sep 17 00:00:00 2001 From: Keerthi Reddy Date: Thu, 28 Sep 2017 00:19:22 +0530 Subject: [PATCH] Staging: pi433: fix grammar issues - This commit fixes spelling issues in documentation files. Signed-off-by: Keerthi Reddy Signed-off-by: Greg Kroah-Hartman --- drivers/staging/pi433/Documentation/pi433.txt | 24 +++++++++---------- 1 file changed, 12 insertions(+), 12 deletions(-) diff --git a/drivers/staging/pi433/Documentation/pi433.txt b/drivers/staging/pi433/Documentation/pi433.txt index 38b83b86c334..245fef33d688 100644 --- a/drivers/staging/pi433/Documentation/pi433.txt +++ b/drivers/staging/pi433/Documentation/pi433.txt @@ -20,7 +20,7 @@ Discription of driver operation a) transmission Each transmission can take place with a different configuration of the rf -module. Therfore each application can set its own set of parameters. The driver +module. Therefore each application can set its own set of parameters. The driver takes care, that each transmission takes place with the parameterset of the application, that requests the transmission. To allow the transmission to take place in the background, a tx thread is introduced. @@ -33,7 +33,7 @@ there is no receive request or the receiver is still waiting for something in the air, the rf module is set to standby, the parameters for transmission gets set, the hardware fifo of the rf chip gets preloaded and the transmission gets started. Upon hardware fifo threshold interrupt it gets reloaded, thus enabling -much longer telegrams then hardware fifo size. If the telegram is send and there +much longer telegrams than the hardware fifo size. If the telegram is sent and there is more data available in the kfifo, the procedure is repeated. If not the transmission cycle ends. @@ -41,7 +41,7 @@ b) reception Since there is only one application allowed to receive data at a time, for reception there is only one configuration set. -As soon as an application sets an request for receiving a telegram, the reception +As soon as an application sets a request for receiving a telegram, the reception configuration set is written to the rf module and it gets set into receiving mode. Now the driver is waiting, that a predefined RSSI level (signal strength at the receiver) is reached. Until this hasn't happened, the reception can be @@ -123,7 +123,7 @@ packet format: optionOff - no preamble will be generated enable_sync optionOn - a sync word will be automatically added to - the telegram after preamble + the telegram after the preamble optionOff - no sync word will be added Attention: While possible to generate sync without preamble, the receiver won't be able to detect the sync without preamble. @@ -136,7 +136,7 @@ packet format: Attention: should be used in combination with sync, only enable_address_byte optionOn - the address byte will be automatically added to the - telgram. It's part of the payload + telegram. It's part of the payload optionOff - the address byte will not be added to the telegram. The address byte can be used for address filtering, so the receiver will only receive telegrams with a given address byte. @@ -161,7 +161,7 @@ packet format: one byte, used as address byte on address byte option. -The rx configuration is transfered via struct pi433_rx_cfg, the parameterset for receiving. It is devided into two sections: rf parameters and packet format. +The rx configuration is transferred via struct pi433_rx_cfg, the parameterset for receiving. It is divided into two sections: rf parameters and packet format. rf params: frequency @@ -178,7 +178,7 @@ rf params: OOK - on off key rssi_threshold threshold value for the signal strength on the receiver input. - If this value is exeeded, a reception cycle starts + If this value is exceeded, a reception cycle starts Allowed values: 0...255 thresholdDecrement in order to adapt to different levels of singnal strength, over @@ -198,7 +198,7 @@ rf params: twohundretOhm - for antennas with an impedance of 200Ohm lnaGain sets the gain of the low noise amp - automatic - lna gain is determed by an agc + automatic - lna gain is determined by an agc max - lna gain is set to maximum maxMinus6 - lna gain is set to 6db below max maxMinus12 - lna gain is set to 12db below max @@ -232,7 +232,7 @@ rf params: amount of bytes that were requested by the read request. Attention: should be used in combination with sync, only enable_address_filtering; - filteringOff - no adress filtering will take place + filteringOff - no address filtering will take place nodeAddress - all telegrams, not matching the node address will be internally discarded nodeOrBroadcastAddress - all telegrams, neither matching the @@ -245,7 +245,7 @@ rf params: calculated crc doesn't match to two bytes, that follow the payload, the telegram will be internally discarded. - Attention: This option is only operational, if sync on and fixed length + Attention: This option is only operational if sync on and fixed length or length byte is used sync_length Gives the length of the payload. @@ -255,9 +255,9 @@ rf params: Overrides the telegram length either given by the first byte of payload or by the read request. bytes_to_drop - gives the number of bytes, that will be dropped before transfering + gives the number of bytes, that will be dropped before transferring data to the read buffer - This option is only usefull, if all packet helper are switched + This option is only useful if all packet helper are switched off and the rf chip is used in raw receiving mode. This may be needed, if a telegram of a third party device should be received, using a protocol not compatible with the packet engine of the rf69 chip.