[SCSI] Remove some unused SCSI-related kernel config variables.

Remove the unused SCSI-related kernel config variables

	SCSI_NCR53C8XX_PROFILE_SUPPORT
	SCSI_NCR53C8XX_PROFILE
	53C700_IO_MAPPED
	AIC79XX_ENABLE_RD_STRM
	AIC7XXX_PROBE_EISA_VL

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This commit is contained in:
Robert P. J. Day 2007-03-26 21:59:33 -08:00 committed by James Bottomley
parent 0d06b281a1
commit b73c3d7786
4 changed files with 0 additions and 43 deletions

View File

@ -562,11 +562,6 @@ if only one has a flaw for some SCSI feature, you can disable the
support by the driver of this feature at linux start-up and enable
this feature after boot-up only for devices that support it safely.
CONFIG_SCSI_NCR53C8XX_PROFILE_SUPPORT (default answer: n)
This option must be set for profiling information to be gathered
and printed out through the proc file system. This features may
impact performances.
CONFIG_SCSI_NCR53C8XX_IOMAPPED (default answer: n)
Answer "y" if you suspect your mother board to not allow memory mapped I/O.
May slow down performance a little. This option is required by

View File

@ -1200,17 +1200,6 @@ config SCSI_NCR53C8XX_SYNC
There is no safe option other than using good cabling, right
terminations and SCSI conformant devices.
config SCSI_NCR53C8XX_PROFILE
bool "enable profiling"
depends on SCSI_ZALON || SCSI_NCR_Q720
help
This option allows you to enable profiling information gathering.
These statistics are not very accurate due to the low frequency
of the kernel clock (100 Hz on i386) and have performance impact
on systems that use very fast devices.
The normal answer therefore is N.
config SCSI_NCR53C8XX_NO_DISCONNECT
bool "not allow targets to disconnect"
depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0
@ -1340,11 +1329,6 @@ config SCSI_SIM710
It currently supports Compaq EISA cards and NCR MCA cards
config 53C700_IO_MAPPED
bool
depends on SCSI_SIM710
default y
config SCSI_SYM53C416
tristate "Symbios 53c416 SCSI support"
depends on ISA && SCSI

View File

@ -57,18 +57,6 @@ config AIC79XX_BUILD_FIRMWARE
or modify the assembler Makefile or the files it includes if your
build environment is different than that of the author.
config AIC79XX_ENABLE_RD_STRM
bool "Enable Read Streaming for All Targets"
depends on SCSI_AIC79XX
default n
help
Read Streaming is a U320 protocol option that should enhance
performance. Early U320 drive firmware actually performs slower
with read streaming enabled so it is disabled by default. Read
Streaming can be configured in much the same way as tagged queueing
using the "rd_strm" command line option. See
drivers/scsi/aic7xxx/README.aic79xx for details.
config AIC79XX_DEBUG_ENABLE
bool "Compile in Debugging Code"
depends on SCSI_AIC79XX

View File

@ -50,16 +50,6 @@ config AIC7XXX_RESET_DELAY_MS
Default: 5000 (5 seconds)
config AIC7XXX_PROBE_EISA_VL
bool "Probe for EISA and VL AIC7XXX Adapters"
depends on SCSI_AIC7XXX && EISA
help
Probe for EISA and VLB Aic7xxx controllers. In many newer systems,
the invasive probes necessary to detect these controllers can cause
other devices to fail. For this reason, the non-PCI probe code is
disabled by default. The current value of this option can be "toggled"
via the no_probe kernel command line option.
config AIC7XXX_BUILD_FIRMWARE
bool "Build Adapter Firmware with Kernel Build"
depends on SCSI_AIC7XXX && !PREVENT_FIRMWARE_BUILD