diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index a96e85397eb7..ac1be25c1e25 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -52,6 +52,7 @@ Table of Contents
       i) Freescale QUICC Engine module (QE)
       j) CFI or JEDEC memory-mapped NOR flash
       k) Global Utilities Block
+      l) Xilinx IP cores
 
   VII - Specifying interrupt information for devices
     1) interrupts property
@@ -851,12 +852,18 @@ address which can extend beyond that limit.
         /cpus/PowerPC,970FX@0
         /cpus/PowerPC,970FX@1
       (unit addresses do not require leading zeroes)
-    - d-cache-line-size : one cell, L1 data cache line size in bytes
-    - i-cache-line-size : one cell, L1 instruction cache line size in
+    - d-cache-block-size : one cell, L1 data cache block size in bytes (*)
+    - i-cache-block-size : one cell, L1 instruction cache block size in
       bytes
     - d-cache-size : one cell, size of L1 data cache in bytes
     - i-cache-size : one cell, size of L1 instruction cache in bytes
 
+(*) The cache "block" size is the size on which the cache management
+instructions operate. Historically, this document used the cache
+"line" size here which is incorrect. The kernel will prefer the cache
+block size and will fallback to cache line size for backward
+compatibility.
+
   Recommended properties:
 
     - timebase-frequency : a cell indicating the frequency of the
@@ -870,6 +877,10 @@ address which can extend beyond that limit.
       for the above, the common code doesn't use that property, but
       you are welcome to re-use the pSeries or Maple one. A future
       kernel version might provide a common function for this.
+    - d-cache-line-size : one cell, L1 data cache line size in bytes
+      if different from the block size
+    - i-cache-line-size : one cell, L1 instruction cache line size in
+      bytes if different from the block size
 
   You are welcome to add any property you find relevant to your board,
   like some information about the mechanism used to soft-reset the
@@ -2242,6 +2253,266 @@ platforms are moved over to use the flattened-device-tree model.
 			   available.
 			   For Axon: 0x0000012a
 
+   l) Xilinx IP cores
+
+   The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
+   in Xilinx Spartan and Virtex FPGAs.  The devices cover the whole range
+   of standard device types (network, serial, etc.) and miscellanious
+   devices (gpio, LCD, spi, etc).  Also, since these devices are
+   implemented within the fpga fabric every instance of the device can be
+   synthesised with different options that change the behaviour.
+
+   Each IP-core has a set of parameters which the FPGA designer can use to
+   control how the core is synthesized.  Historically, the EDK tool would
+   extract the device parameters relevant to device drivers and copy them
+   into an 'xparameters.h' in the form of #define symbols.  This tells the
+   device drivers how the IP cores are configured, but it requres the kernel
+   to be recompiled every time the FPGA bitstream is resynthesized.
+
+   The new approach is to export the parameters into the device tree and
+   generate a new device tree each time the FPGA bitstream changes.  The
+   parameters which used to be exported as #defines will now become
+   properties of the device node.  In general, device nodes for IP-cores
+   will take the following form:
+
+	(name)@(base-address) {
+		compatible = "xlnx,(ip-core-name)-(HW_VER)"
+			     [, (list of compatible devices), ...];
+		reg = <(baseaddr) (size)>;
+		interrupt-parent = <&interrupt-controller-phandle>;
+		interrupts = < ... >;
+		xlnx,(parameter1) = "(string-value)";
+		xlnx,(parameter2) = <(int-value)>;
+	};
+
+	(ip-core-name):	the name of the ip block (given after the BEGIN
+			directive in system.mhs).  Should be in lowercase
+			and all underscores '_' converted to dashes '-'.
+	(name):		is derived from the "PARAMETER INSTANCE" value.
+	(parameter#):	C_* parameters from system.mhs.  The C_ prefix is
+			dropped from the parameter name, the name is converted
+			to lowercase and all underscore '_' characters are
+			converted to dashes '-'.
+	(baseaddr):	the C_BASEADDR parameter.
+	(HW_VER):	from the HW_VER parameter.
+	(size):		equals C_HIGHADDR - C_BASEADDR + 1
+
+   Typically, the compatible list will include the exact IP core version
+   followed by an older IP core version which implements the same
+   interface or any other device with the same interface.
+
+   'reg', 'interrupt-parent' and 'interrupts' are all optional properties.
+
+   For example, the following block from system.mhs:
+
+	BEGIN opb_uartlite
+		PARAMETER INSTANCE = opb_uartlite_0
+		PARAMETER HW_VER = 1.00.b
+		PARAMETER C_BAUDRATE = 115200
+		PARAMETER C_DATA_BITS = 8
+		PARAMETER C_ODD_PARITY = 0
+		PARAMETER C_USE_PARITY = 0
+		PARAMETER C_CLK_FREQ = 50000000
+		PARAMETER C_BASEADDR = 0xEC100000
+		PARAMETER C_HIGHADDR = 0xEC10FFFF
+		BUS_INTERFACE SOPB = opb_7
+		PORT OPB_Clk = CLK_50MHz
+		PORT Interrupt = opb_uartlite_0_Interrupt
+		PORT RX = opb_uartlite_0_RX
+		PORT TX = opb_uartlite_0_TX
+		PORT OPB_Rst = sys_bus_reset_0
+	END
+
+   becomes the following device tree node:
+
+	opb-uartlite-0@ec100000 {
+		device_type = "serial";
+		compatible = "xlnx,opb-uartlite-1.00.b";
+		reg = <ec100000 10000>;
+		interrupt-parent = <&opb-intc>;
+		interrupts = <1 0>; // got this from the opb_intc parameters
+		current-speed = <d#115200>;	// standard serial device prop
+		clock-frequency = <d#50000000>;	// standard serial device prop
+		xlnx,data-bits = <8>;
+		xlnx,odd-parity = <0>;
+		xlnx,use-parity = <0>;
+	};
+
+   Some IP cores actually implement 2 or more logical devices.  In this case,
+   the device should still describe the whole IP core with a single node
+   and add a child node for each logical device.  The ranges property can
+   be used to translate from parent IP-core to the registers of each device.
+   (Note: this makes the assumption that both logical devices have the same
+   bus binding.  If this is not true, then separate nodes should be used for
+   each logical device).  The 'cell-index' property can be used to enumerate
+   logical devices within an IP core.  For example, the following is the
+   system.mhs entry for the dual ps2 controller found on the ml403 reference
+   design.
+
+	BEGIN opb_ps2_dual_ref
+		PARAMETER INSTANCE = opb_ps2_dual_ref_0
+		PARAMETER HW_VER = 1.00.a
+		PARAMETER C_BASEADDR = 0xA9000000
+		PARAMETER C_HIGHADDR = 0xA9001FFF
+		BUS_INTERFACE SOPB = opb_v20_0
+		PORT Sys_Intr1 = ps2_1_intr
+		PORT Sys_Intr2 = ps2_2_intr
+		PORT Clkin1 = ps2_clk_rx_1
+		PORT Clkin2 = ps2_clk_rx_2
+		PORT Clkpd1 = ps2_clk_tx_1
+		PORT Clkpd2 = ps2_clk_tx_2
+		PORT Rx1 = ps2_d_rx_1
+		PORT Rx2 = ps2_d_rx_2
+		PORT Txpd1 = ps2_d_tx_1
+		PORT Txpd2 = ps2_d_tx_2
+	END
+
+   It would result in the following device tree nodes:
+
+	opb_ps2_dual_ref_0@a9000000 {
+		ranges = <0 a9000000 2000>;
+		// If this device had extra parameters, then they would
+		// go here.
+		ps2@0 {
+			compatible = "xlnx,opb-ps2-dual-ref-1.00.a";
+			reg = <0 40>;
+			interrupt-parent = <&opb-intc>;
+			interrupts = <3 0>;
+			cell-index = <0>;
+		};
+		ps2@1000 {
+			compatible = "xlnx,opb-ps2-dual-ref-1.00.a";
+			reg = <1000 40>;
+			interrupt-parent = <&opb-intc>;
+			interrupts = <3 0>;
+			cell-index = <0>;
+		};
+	};
+
+   Also, the system.mhs file defines bus attachments from the processor
+   to the devices.  The device tree structure should reflect the bus
+   attachments.  Again an example; this system.mhs fragment:
+
+	BEGIN ppc405_virtex4
+		PARAMETER INSTANCE = ppc405_0
+		PARAMETER HW_VER = 1.01.a
+		BUS_INTERFACE DPLB = plb_v34_0
+		BUS_INTERFACE IPLB = plb_v34_0
+	END
+
+	BEGIN opb_intc
+		PARAMETER INSTANCE = opb_intc_0
+		PARAMETER HW_VER = 1.00.c
+		PARAMETER C_BASEADDR = 0xD1000FC0
+		PARAMETER C_HIGHADDR = 0xD1000FDF
+		BUS_INTERFACE SOPB = opb_v20_0
+	END
+
+	BEGIN opb_uart16550
+		PARAMETER INSTANCE = opb_uart16550_0
+		PARAMETER HW_VER = 1.00.d
+		PARAMETER C_BASEADDR = 0xa0000000
+		PARAMETER C_HIGHADDR = 0xa0001FFF
+		BUS_INTERFACE SOPB = opb_v20_0
+	END
+
+	BEGIN plb_v34
+		PARAMETER INSTANCE = plb_v34_0
+		PARAMETER HW_VER = 1.02.a
+	END
+
+	BEGIN plb_bram_if_cntlr
+		PARAMETER INSTANCE = plb_bram_if_cntlr_0
+		PARAMETER HW_VER = 1.00.b
+		PARAMETER C_BASEADDR = 0xFFFF0000
+		PARAMETER C_HIGHADDR = 0xFFFFFFFF
+		BUS_INTERFACE SPLB = plb_v34_0
+	END
+
+	BEGIN plb2opb_bridge
+		PARAMETER INSTANCE = plb2opb_bridge_0
+		PARAMETER HW_VER = 1.01.a
+		PARAMETER C_RNG0_BASEADDR = 0x20000000
+		PARAMETER C_RNG0_HIGHADDR = 0x3FFFFFFF
+		PARAMETER C_RNG1_BASEADDR = 0x60000000
+		PARAMETER C_RNG1_HIGHADDR = 0x7FFFFFFF
+		PARAMETER C_RNG2_BASEADDR = 0x80000000
+		PARAMETER C_RNG2_HIGHADDR = 0xBFFFFFFF
+		PARAMETER C_RNG3_BASEADDR = 0xC0000000
+		PARAMETER C_RNG3_HIGHADDR = 0xDFFFFFFF
+		BUS_INTERFACE SPLB = plb_v34_0
+		BUS_INTERFACE MOPB = opb_v20_0
+	END
+
+   Gives this device tree (some properties removed for clarity):
+
+	plb-v34-0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		device_type = "ibm,plb";
+		ranges; // 1:1 translation
+
+		plb-bram-if-cntrl-0@ffff0000 {
+			reg = <ffff0000 10000>;
+		}
+
+		opb-v20-0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <20000000 20000000 20000000
+				  60000000 60000000 20000000
+				  80000000 80000000 40000000
+				  c0000000 c0000000 20000000>;
+
+			opb-uart16550-0@a0000000 {
+				reg = <a00000000 2000>;
+			};
+
+			opb-intc-0@d1000fc0 {
+				reg = <d1000fc0 20>;
+			};
+		};
+	};
+
+   That covers the general approach to binding xilinx IP cores into the
+   device tree.  The following are bindings for specific devices:
+
+      i) Xilinx ML300 Framebuffer
+
+      Simple framebuffer device from the ML300 reference design (also on the
+      ML403 reference design as well as others).
+
+      Optional properties:
+       - resolution = <xres yres> : pixel resolution of framebuffer.  Some
+                                    implementations use a different resolution.
+                                    Default is <d#640 d#480>
+       - virt-resolution = <xvirt yvirt> : Size of framebuffer in memory.
+                                           Default is <d#1024 d#480>.
+       - rotate-display (empty) : rotate display 180 degrees.
+
+      ii) Xilinx SystemACE
+
+      The Xilinx SystemACE device is used to program FPGAs from an FPGA
+      bitstream stored on a CF card.  It can also be used as a generic CF
+      interface device.
+
+      Optional properties:
+       - 8-bit (empty) : Set this property for SystemACE in 8 bit mode
+
+      iii) Xilinx EMAC and Xilinx TEMAC
+
+      Xilinx Ethernet devices.  In addition to general xilinx properties
+      listed above, nodes for these devices should include a phy-handle
+      property, and may include other common network device properties
+      like local-mac-address.
+      
+      iv) Xilinx Uartlite
+
+      Xilinx uartlite devices are simple fixed speed serial ports.
+
+      Requred properties:
+       - current-speed : Baud rate of uartlite
+
    More devices will be defined as this spec matures.
 
 VII - Specifying interrupt information for devices
diff --git a/arch/powerpc/boot/dts/walnut.dts b/arch/powerpc/boot/dts/walnut.dts
index fa681f5343fe..754fa3960f83 100644
--- a/arch/powerpc/boot/dts/walnut.dts
+++ b/arch/powerpc/boot/dts/walnut.dts
@@ -122,7 +122,9 @@
 				device_type = "network";
 				compatible = "ibm,emac-405gp", "ibm,emac";
 				interrupt-parent = <&UIC0>;
-				interrupts = <9 4 f 4>;
+				interrupts = <
+					f 4 /* Ethernet */
+					9 4 /* Ethernet Wake Up */>;
 				local-mac-address = [000000000000]; /* Filled in by zImage */
 				reg = <ef600800 70>;
 				mal-device = <&MAL>;
diff --git a/arch/powerpc/boot/wrapper b/arch/powerpc/boot/wrapper
index 39b27e5ef6c1..31147a037728 100755
--- a/arch/powerpc/boot/wrapper
+++ b/arch/powerpc/boot/wrapper
@@ -21,6 +21,14 @@
 #		(default ./arch/powerpc/boot)
 # -W dir	specify working directory for temporary files (default .)
 
+# Stop execution if any command fails
+set -e
+
+# Allow for verbose output
+if [ "$V" = 1 ]; then
+    set -x
+fi
+
 # defaults
 kernel=
 ofile=zImage
@@ -111,7 +119,7 @@ if [ -n "$dts" ]; then
     if [ -z "$dtb" ]; then
 	dtb="$platform.dtb"
     fi
-    dtc -O dtb -o "$dtb" -b 0 -V 16 "$dts" || exit 1
+    dtc -O dtb -o "$dtb" -b 0 -V 16 "$dts"
 fi
 
 if [ -z "$kernel" ]; then
@@ -149,7 +157,6 @@ cuboot*)
 ps3)
     platformo="$object/ps3-head.o $object/ps3-hvcall.o $object/ps3.o"
     lds=$object/zImage.ps3.lds
-    binary=y
     gzip=
     ext=bin
     objflags="-O binary --set-section-flags=.bss=contents,alloc,load,data"
@@ -233,7 +240,7 @@ entry=`${CROSS}objdump -f "$ofile" | grep '^start address ' | cut -d' ' -f3`
 
 if [ -n "$binary" ]; then
     mv "$ofile" "$ofile".elf
-    ${CROSS}objcopy -O binary "$ofile".elf "$ofile".bin
+    ${CROSS}objcopy -O binary "$ofile".elf "$ofile"
 fi
 
 # post-processing needed for some platforms
@@ -246,9 +253,9 @@ coff)
     $object/hack-coff "$ofile"
     ;;
 cuboot*)
-    gzip -f -9 "$ofile".bin
+    gzip -f -9 "$ofile"
     mkimage -A ppc -O linux -T kernel -C gzip -a "$base" -e "$entry" \
-            $uboot_version -d "$ofile".bin.gz "$ofile"
+            $uboot_version -d "$ofile".gz "$ofile"
     ;;
 treeboot*)
     mv "$ofile" "$ofile.elf"
@@ -269,11 +276,11 @@ ps3)
     # then copied to offset 0x100.  At runtime the bootwrapper program
     # copies the 0x100 bytes at __system_reset_kernel to addr 0x100.
 
-    system_reset_overlay=0x`${CROSS}nm "$ofile".elf \
+    system_reset_overlay=0x`${CROSS}nm "$ofile" \
         | grep ' __system_reset_overlay$'       \
         | cut -d' ' -f1`
     system_reset_overlay=`printf "%d" $system_reset_overlay`
-    system_reset_kernel=0x`${CROSS}nm "$ofile".elf \
+    system_reset_kernel=0x`${CROSS}nm "$ofile" \
         | grep ' __system_reset_kernel$'       \
         | cut -d' ' -f1`
     system_reset_kernel=`printf "%d" $system_reset_kernel`
@@ -282,23 +289,15 @@ ps3)
 
     rm -f "$object/otheros.bld"
 
-    msg=$(dd if="$ofile.bin" of="$ofile.bin" conv=notrunc \
-        skip=$overlay_dest seek=$system_reset_kernel      \
-        count=$overlay_size bs=1 2>&1)
+    ${CROSS}objcopy -O binary "$ofile" "$ofile.bin"
 
-    if [ $? -ne "0" ]; then
-       echo $msg
-       exit 1
-    fi
+    dd if="$ofile.bin" of="$ofile.bin" conv=notrunc   \
+        skip=$overlay_dest seek=$system_reset_kernel  \
+        count=$overlay_size bs=1
 
-    msg=$(dd if="$ofile.bin" of="$ofile.bin" conv=notrunc \
-        skip=$system_reset_overlay seek=$overlay_dest     \
-        count=$overlay_size bs=1 2>&1)
-
-    if [ $? -ne "0" ]; then
-       echo $msg
-       exit 2
-    fi
+    dd if="$ofile.bin" of="$ofile.bin" conv=notrunc   \
+        skip=$system_reset_overlay seek=$overlay_dest \
+        count=$overlay_size bs=1
 
     gzip --force -9 --stdout "$ofile.bin" > "$object/otheros.bld"
     ;;
diff --git a/arch/powerpc/configs/pasemi_defconfig b/arch/powerpc/configs/pasemi_defconfig
index 1ccf3ed7693e..78c968aade4e 100644
--- a/arch/powerpc/configs/pasemi_defconfig
+++ b/arch/powerpc/configs/pasemi_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc4
-# Thu Aug 30 16:40:47 2007
+# Linux kernel version: 2.6.24-rc2
+# Tue Nov  6 23:23:50 2007
 #
 CONFIG_PPC64=y
 
@@ -10,6 +10,7 @@ CONFIG_PPC64=y
 #
 CONFIG_POWER4_ONLY=y
 CONFIG_POWER4=y
+# CONFIG_TUNE_CELL is not set
 CONFIG_PPC_FPU=y
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
@@ -18,8 +19,13 @@ CONFIG_PPC_MM_SLICES=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_64BIT=y
+CONFIG_WORD_SIZE=64
 CONFIG_PPC_MERGE=y
 CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
 CONFIG_IRQ_PER_CPU=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
@@ -65,7 +71,10 @@ CONFIG_SYSVIPC_SYSCTL=y
 # CONFIG_AUDIT is not set
 # CONFIG_IKCONFIG is not set
 CONFIG_LOG_BUF_SHIFT=17
-# CONFIG_CPUSETS is not set
+# CONFIG_CGROUPS is not set
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
 CONFIG_SYSFS_DEPRECATED=y
 # CONFIG_RELAY is not set
 CONFIG_BLK_DEV_INITRD=y
@@ -86,7 +95,6 @@ CONFIG_FUTEX=y
 CONFIG_ANON_INODES=y
 CONFIG_EPOLL=y
 CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_VM_EVENT_COUNTERS=y
@@ -107,14 +115,15 @@ CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
 # CONFIG_BLK_DEV_IO_TRACE is not set
 # CONFIG_BLK_DEV_BSG is not set
+CONFIG_BLOCK_COMPAT=y
 
 #
 # IO Schedulers
 #
 CONFIG_IOSCHED_NOOP=y
 CONFIG_IOSCHED_AS=y
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
 CONFIG_DEFAULT_AS=y
 # CONFIG_DEFAULT_DEADLINE is not set
 # CONFIG_DEFAULT_CFQ is not set
@@ -125,7 +134,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory"
 # Platform support
 #
 CONFIG_PPC_MULTIPLATFORM=y
-# CONFIG_EMBEDDED6xx is not set
 # CONFIG_PPC_82xx is not set
 # CONFIG_PPC_83xx is not set
 # CONFIG_PPC_86xx is not set
@@ -141,6 +149,7 @@ CONFIG_PPC_PASEMI=y
 # PA Semi PWRficient options
 #
 CONFIG_PPC_PASEMI_IOMMU=y
+# CONFIG_PPC_PASEMI_IOMMU_DMA_FORCE is not set
 CONFIG_PPC_PASEMI_MDIO=y
 CONFIG_ELECTRA_IDE=y
 # CONFIG_PPC_CELLEB is not set
@@ -156,29 +165,52 @@ CONFIG_MPIC=y
 # CONFIG_U3_DART is not set
 # CONFIG_PPC_RTAS is not set
 # CONFIG_MMIO_NVRAM is not set
+CONFIG_MPIC_BROKEN_REGREAD=y
 # CONFIG_PPC_MPC106 is not set
 # CONFIG_PPC_970_NAP is not set
 # CONFIG_PPC_INDIRECT_IO is not set
 # CONFIG_GENERIC_IOMAP is not set
-# CONFIG_CPU_FREQ is not set
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_TABLE=y
+CONFIG_CPU_FREQ_DEBUG=y
+CONFIG_CPU_FREQ_STAT=y
+# CONFIG_CPU_FREQ_STAT_DETAILS is not set
+CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+
+#
+# CPU Frequency drivers
+#
+CONFIG_PPC_PASEMI_CPUFREQ=y
 # CONFIG_CPM2 is not set
 # CONFIG_FSL_ULI1575 is not set
 
 #
 # Kernel options
 #
-CONFIG_HZ_100=y
+CONFIG_TICK_ONESHOT=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+# CONFIG_HZ_100 is not set
 # CONFIG_HZ_250 is not set
 # CONFIG_HZ_300 is not set
-# CONFIG_HZ_1000 is not set
-CONFIG_HZ=100
+CONFIG_HZ_1000=y
+CONFIG_HZ=1000
 CONFIG_PREEMPT_NONE=y
 # CONFIG_PREEMPT_VOLUNTARY is not set
 # CONFIG_PREEMPT is not set
-CONFIG_PREEMPT_BKL=y
+# CONFIG_PREEMPT_BKL is not set
 CONFIG_BINFMT_ELF=y
 # CONFIG_BINFMT_MISC is not set
-CONFIG_FORCE_MAX_ZONEORDER=13
+CONFIG_FORCE_MAX_ZONEORDER=9
 CONFIG_IOMMU_VMERGE=y
 CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
 # CONFIG_KEXEC is not set
@@ -196,12 +228,13 @@ CONFIG_FLATMEM_MANUAL=y
 CONFIG_FLATMEM=y
 CONFIG_FLAT_NODE_MEM_MAP=y
 # CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
 CONFIG_SPLIT_PTLOCK_CPUS=4
 CONFIG_RESOURCES_64BIT=y
 CONFIG_ZONE_DMA_FLAG=1
 CONFIG_BOUNCE=y
-# CONFIG_PPC_HAS_HASH_64K is not set
-# CONFIG_PPC_64K_PAGES is not set
+CONFIG_PPC_HAS_HASH_64K=y
+CONFIG_PPC_64K_PAGES=y
 # CONFIG_SCHED_SMT is not set
 CONFIG_PROC_DEVICETREE=y
 # CONFIG_CMDLINE_BOOL is not set
@@ -222,11 +255,8 @@ CONFIG_PCI_SYSCALL=y
 # CONFIG_PCIEPORTBUS is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
 # CONFIG_PCI_MSI is not set
+CONFIG_PCI_LEGACY=y
 # CONFIG_PCI_DEBUG is not set
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
 CONFIG_PCCARD=y
 CONFIG_PCMCIA_DEBUG=y
 CONFIG_PCMCIA=y
@@ -240,6 +270,7 @@ CONFIG_CARDBUS=y
 # CONFIG_YENTA is not set
 # CONFIG_PD6729 is not set
 # CONFIG_I82092 is not set
+# CONFIG_ELECTRA_CF is not set
 # CONFIG_HOTPLUG_PCI is not set
 CONFIG_KERNEL_START=0xc000000000000000
 
@@ -255,7 +286,7 @@ CONFIG_PACKET=y
 # CONFIG_PACKET_MMAP is not set
 CONFIG_UNIX=y
 CONFIG_XFRM=y
-# CONFIG_XFRM_USER is not set
+CONFIG_XFRM_USER=y
 # CONFIG_XFRM_SUB_POLICY is not set
 # CONFIG_XFRM_MIGRATE is not set
 CONFIG_NET_KEY=y
@@ -281,6 +312,7 @@ CONFIG_INET_TUNNEL=y
 CONFIG_INET_XFRM_MODE_TRANSPORT=y
 CONFIG_INET_XFRM_MODE_TUNNEL=y
 CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_LRO=y
 CONFIG_INET_DIAG=y
 CONFIG_INET_TCP_DIAG=y
 # CONFIG_TCP_CONG_ADVANCED is not set
@@ -306,10 +338,6 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 # CONFIG_LAPB is not set
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
 # CONFIG_NET_SCHED is not set
 
 #
@@ -338,6 +366,7 @@ CONFIG_DEFAULT_TCP_CONG="cubic"
 #
 # Generic Driver Options
 #
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
 CONFIG_FW_LOADER=y
@@ -361,6 +390,7 @@ CONFIG_MTD_BLOCK=y
 # CONFIG_INFTL is not set
 # CONFIG_RFD_FTL is not set
 # CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
 
 #
 # RAM/ROM/Flash chip drivers
@@ -385,6 +415,7 @@ CONFIG_MTD_CFI_I2=y
 # Mapping drivers for chip access
 #
 # CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_INTEL_VR_NOR is not set
 # CONFIG_MTD_PLATRAM is not set
 
 #
@@ -402,7 +433,15 @@ CONFIG_MTD_PHRAM=y
 # CONFIG_MTD_DOC2000 is not set
 # CONFIG_MTD_DOC2001 is not set
 # CONFIG_MTD_DOC2001PLUS is not set
-# CONFIG_MTD_NAND is not set
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_CAFE is not set
+# CONFIG_MTD_NAND_PLATFORM is not set
+# CONFIG_MTD_ALAUDA is not set
 # CONFIG_MTD_ONENAND is not set
 
 #
@@ -455,10 +494,42 @@ CONFIG_IDE_PROC_FS=y
 # IDE chipset support/bugfixes
 #
 # CONFIG_IDE_GENERIC is not set
-# CONFIG_BLK_DEV_IDEPCI is not set
+# CONFIG_BLK_DEV_PLATFORM is not set
+
+#
+# PCI IDE chipsets support
+#
 # CONFIG_IDEPCI_PCIBUS_ORDER is not set
+# CONFIG_BLK_DEV_GENERIC is not set
+# CONFIG_BLK_DEV_OPTI621 is not set
+# CONFIG_BLK_DEV_AEC62XX is not set
+# CONFIG_BLK_DEV_ALI15X3 is not set
+# CONFIG_BLK_DEV_AMD74XX is not set
+# CONFIG_BLK_DEV_CMD64X is not set
+# CONFIG_BLK_DEV_TRIFLEX is not set
+# CONFIG_BLK_DEV_CY82C693 is not set
+# CONFIG_BLK_DEV_CS5520 is not set
+# CONFIG_BLK_DEV_CS5530 is not set
+# CONFIG_BLK_DEV_HPT34X is not set
+# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_JMICRON is not set
+# CONFIG_BLK_DEV_SC1200 is not set
+# CONFIG_BLK_DEV_PIIX is not set
+# CONFIG_BLK_DEV_IT8213 is not set
+# CONFIG_BLK_DEV_IT821X is not set
+# CONFIG_BLK_DEV_NS87415 is not set
+# CONFIG_BLK_DEV_PDC202XX_OLD is not set
+# CONFIG_BLK_DEV_PDC202XX_NEW is not set
+# CONFIG_BLK_DEV_SVWKS is not set
+# CONFIG_BLK_DEV_SIIMAGE is not set
+# CONFIG_BLK_DEV_SL82C105 is not set
+# CONFIG_BLK_DEV_SLC90E66 is not set
+# CONFIG_BLK_DEV_TRM290 is not set
+# CONFIG_BLK_DEV_VIA82CXXX is not set
+# CONFIG_BLK_DEV_TC86C001 is not set
 # CONFIG_IDE_ARM is not set
 # CONFIG_BLK_DEV_IDEDMA is not set
+CONFIG_IDE_ARCH_OBSOLETE_INIT=y
 # CONFIG_BLK_DEV_HD is not set
 
 #
@@ -498,10 +569,11 @@ CONFIG_SCSI_WAIT_SCAN=m
 # CONFIG_SCSI_FC_ATTRS is not set
 # CONFIG_SCSI_ISCSI_ATTRS is not set
 # CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
-CONFIG_BLK_DEV_3W_XXXX_RAID=y
-CONFIG_SCSI_3W_9XXX=y
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
 # CONFIG_SCSI_ACARD is not set
 # CONFIG_SCSI_AACRAID is not set
 # CONFIG_SCSI_AIC7XXX is not set
@@ -574,9 +646,10 @@ CONFIG_ATA_GENERIC=y
 # CONFIG_PATA_OLDPIIX is not set
 # CONFIG_PATA_NETCELL is not set
 # CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_NS87415 is not set
 # CONFIG_PATA_OPTI is not set
 # CONFIG_PATA_OPTIDMA is not set
-# CONFIG_PATA_PCMCIA is not set
+CONFIG_PATA_PCMCIA=y
 # CONFIG_PATA_PDC_OLD is not set
 # CONFIG_PATA_RADISYS is not set
 # CONFIG_PATA_RZ1000 is not set
@@ -589,41 +662,13 @@ CONFIG_ATA_GENERIC=y
 # CONFIG_PATA_WINBOND is not set
 CONFIG_PATA_PLATFORM=y
 # CONFIG_MD is not set
-
-#
-# Fusion MPT device support
-#
 # CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
-# CONFIG_FUSION_SAS is not set
 
 #
 # IEEE 1394 (FireWire) support
 #
 # CONFIG_FIREWIRE is not set
-CONFIG_IEEE1394=y
-
-#
-# Subsystem Options
-#
-# CONFIG_IEEE1394_VERBOSEDEBUG is not set
-
-#
-# Controllers
-#
-CONFIG_IEEE1394_PCILYNX=y
-CONFIG_IEEE1394_OHCI1394=y
-
-#
-# Protocols
-#
-# CONFIG_IEEE1394_VIDEO1394 is not set
-CONFIG_IEEE1394_SBP2=y
-# CONFIG_IEEE1394_ETH1394_ROM_ENTRY is not set
-# CONFIG_IEEE1394_ETH1394 is not set
-# CONFIG_IEEE1394_DV1394 is not set
-CONFIG_IEEE1394_RAWIO=y
+# CONFIG_IEEE1394 is not set
 # CONFIG_I2O is not set
 # CONFIG_MACINTOSH_DRIVERS is not set
 CONFIG_NETDEVICES=y
@@ -633,6 +678,8 @@ CONFIG_DUMMY=y
 # CONFIG_MACVLAN is not set
 # CONFIG_EQUALIZER is not set
 # CONFIG_TUN is not set
+# CONFIG_VETH is not set
+# CONFIG_IP1000 is not set
 # CONFIG_ARCNET is not set
 CONFIG_PHYLIB=y
 
@@ -649,6 +696,7 @@ CONFIG_MARVELL_PHY=y
 # CONFIG_BROADCOM_PHY is not set
 # CONFIG_ICPLUS_PHY is not set
 # CONFIG_FIXED_PHY is not set
+# CONFIG_MDIO_BITBANG is not set
 CONFIG_NET_ETHERNET=y
 CONFIG_MII=y
 # CONFIG_HAPPYMEAL is not set
@@ -657,13 +705,16 @@ CONFIG_MII=y
 # CONFIG_NET_VENDOR_3COM is not set
 # CONFIG_NET_TULIP is not set
 # CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
 CONFIG_NET_PCI=y
 # CONFIG_PCNET32 is not set
 # CONFIG_AMD8111_ETH is not set
 # CONFIG_ADAPTEC_STARFIRE is not set
 # CONFIG_B44 is not set
 # CONFIG_FORCEDETH is not set
-# CONFIG_DGRS is not set
 # CONFIG_EEPRO100 is not set
 # CONFIG_E100 is not set
 # CONFIG_FEALNX is not set
@@ -682,6 +733,7 @@ CONFIG_NETDEV_1000=y
 CONFIG_E1000=y
 CONFIG_E1000_NAPI=y
 # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
+# CONFIG_E1000E is not set
 # CONFIG_NS83820 is not set
 # CONFIG_HAMACHI is not set
 # CONFIG_YELLOWFIN is not set
@@ -689,6 +741,7 @@ CONFIG_E1000_NAPI=y
 # CONFIG_SIS190 is not set
 # CONFIG_SKGE is not set
 # CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
 # CONFIG_VIA_VELOCITY is not set
 CONFIG_TIGON3=y
 # CONFIG_BNX2 is not set
@@ -697,12 +750,15 @@ CONFIG_TIGON3=y
 CONFIG_NETDEV_10000=y
 # CONFIG_CHELSIO_T1 is not set
 # CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
 # CONFIG_IXGB is not set
 # CONFIG_S2IO is not set
 # CONFIG_MYRI10GE is not set
 # CONFIG_NETXEN_NIC is not set
+# CONFIG_NIU is not set
 CONFIG_PASEMI_MAC=y
 # CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
 # CONFIG_TR is not set
 
 #
@@ -749,7 +805,6 @@ CONFIG_INPUT_MOUSEDEV_PSAUX=y
 CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
 CONFIG_INPUT_JOYDEV=y
-# CONFIG_INPUT_TSDEV is not set
 CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_EVBUG is not set
 
@@ -810,15 +865,12 @@ CONFIG_UNIX98_PTYS=y
 CONFIG_LEGACY_PTYS=y
 CONFIG_LEGACY_PTY_COUNT=4
 # CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
 CONFIG_HW_RANDOM=y
 CONFIG_HW_RANDOM_PASEMI=y
 CONFIG_GEN_RTC=y
 CONFIG_GEN_RTC_X=y
 # CONFIG_R3964 is not set
 # CONFIG_APPLICOM is not set
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
 
 #
 # PCMCIA character devices
@@ -896,8 +948,6 @@ CONFIG_SENSORS_EEPROM=y
 # CONFIG_POWER_SUPPLY is not set
 CONFIG_HWMON=y
 CONFIG_HWMON_VID=y
-# CONFIG_SENSORS_ABITUGURU is not set
-# CONFIG_SENSORS_ABITUGURU3 is not set
 # CONFIG_SENSORS_AD7418 is not set
 # CONFIG_SENSORS_ADM1021 is not set
 # CONFIG_SENSORS_ADM1025 is not set
@@ -905,12 +955,12 @@ CONFIG_HWMON_VID=y
 # CONFIG_SENSORS_ADM1029 is not set
 # CONFIG_SENSORS_ADM1031 is not set
 # CONFIG_SENSORS_ADM9240 is not set
-# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ADT7470 is not set
 # CONFIG_SENSORS_ATXP1 is not set
 # CONFIG_SENSORS_DS1621 is not set
 # CONFIG_SENSORS_F71805F is not set
-# CONFIG_SENSORS_FSCHER is not set
-# CONFIG_SENSORS_FSCPOS is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
 # CONFIG_SENSORS_GL518SM is not set
 # CONFIG_SENSORS_GL520SM is not set
 # CONFIG_SENSORS_IT87 is not set
@@ -946,6 +996,13 @@ CONFIG_SENSORS_LM90=y
 # CONFIG_SENSORS_W83627HF is not set
 # CONFIG_SENSORS_W83627EHF is not set
 # CONFIG_HWMON_DEBUG_CHIP is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
 
 #
 # Multifunction device drivers
@@ -963,14 +1020,14 @@ CONFIG_DAB=y
 #
 # Graphics support
 #
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_LCD_CLASS_DEVICE=m
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-
-#
-# Display device support
-#
-# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_AGP is not set
+CONFIG_DRM=y
+# CONFIG_DRM_TDFX is not set
+# CONFIG_DRM_R128 is not set
+CONFIG_DRM_RADEON=y
+# CONFIG_DRM_MGA is not set
+# CONFIG_DRM_VIA is not set
+# CONFIG_DRM_SAVAGE is not set
 CONFIG_VGASTATE=y
 # CONFIG_VIDEO_OUTPUT_CONTROL is not set
 CONFIG_FB=y
@@ -979,6 +1036,7 @@ CONFIG_FB_DDC=y
 CONFIG_FB_CFB_FILLRECT=y
 CONFIG_FB_CFB_COPYAREA=y
 CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
 # CONFIG_FB_SYS_FILLRECT is not set
 # CONFIG_FB_SYS_COPYAREA is not set
 # CONFIG_FB_SYS_IMAGEBLIT is not set
@@ -1026,6 +1084,15 @@ CONFIG_FB_RADEON_BACKLIGHT=y
 # CONFIG_FB_PM3 is not set
 # CONFIG_FB_IBM_GXT4500 is not set
 # CONFIG_FB_VIRTUAL is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+# CONFIG_LCD_CLASS_DEVICE is not set
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_CORGI is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
 
 #
 # Console display driver support
@@ -1178,6 +1245,7 @@ CONFIG_SND_USB_USX2Y=y
 CONFIG_HID_SUPPORT=y
 CONFIG_HID=y
 # CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
 
 #
 # USB Input Devices
@@ -1328,6 +1396,7 @@ CONFIG_RTC_INTF_DEV=y
 # I2C RTC drivers
 #
 CONFIG_RTC_DRV_DS1307=y
+# CONFIG_RTC_DRV_DS1374 is not set
 # CONFIG_RTC_DRV_DS1672 is not set
 # CONFIG_RTC_DRV_MAX6900 is not set
 # CONFIG_RTC_DRV_RS5C372 is not set
@@ -1356,19 +1425,6 @@ CONFIG_RTC_DRV_DS1307=y
 # on-CPU RTC drivers
 #
 
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
-
 #
 # Userspace I/O
 #
@@ -1388,7 +1444,6 @@ CONFIG_EXT3_FS_XATTR=y
 # CONFIG_EXT3_FS_SECURITY is not set
 # CONFIG_EXT4DEV_FS is not set
 CONFIG_JBD=y
-# CONFIG_JBD_DEBUG is not set
 CONFIG_FS_MBCACHE=y
 # CONFIG_REISERFS_FS is not set
 # CONFIG_JFS_FS is not set
@@ -1436,7 +1491,6 @@ CONFIG_TMPFS=y
 # CONFIG_TMPFS_POSIX_ACL is not set
 CONFIG_HUGETLBFS=y
 CONFIG_HUGETLB_PAGE=y
-CONFIG_RAMFS=y
 CONFIG_CONFIGFS_FS=y
 
 #
@@ -1449,30 +1503,43 @@ CONFIG_CONFIGFS_FS=y
 # CONFIG_BEFS_FS is not set
 # CONFIG_BFS_FS is not set
 # CONFIG_EFS_FS is not set
-# CONFIG_JFFS2_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
 # CONFIG_CRAMFS is not set
 # CONFIG_VXFS_FS is not set
 # CONFIG_HPFS_FS is not set
 # CONFIG_QNX4FS_FS is not set
 # CONFIG_SYSV_FS is not set
 # CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 # CONFIG_NFS_V3_ACL is not set
 # CONFIG_NFS_V4 is not set
 # CONFIG_NFS_DIRECTIO is not set
-# CONFIG_NFSD is not set
+CONFIG_NFSD=y
+CONFIG_NFSD_V3=y
+# CONFIG_NFSD_V3_ACL is not set
+CONFIG_NFSD_V4=y
+CONFIG_NFSD_TCP=y
 CONFIG_ROOT_NFS=y
 CONFIG_LOCKD=y
 CONFIG_LOCKD_V4=y
+CONFIG_EXPORTFS=y
 CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
 # CONFIG_SUNRPC_BIND34 is not set
-# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_RPCSEC_GSS_KRB5=y
 # CONFIG_RPCSEC_GSS_SPKM3 is not set
 # CONFIG_SMB_FS is not set
 # CONFIG_CIFS is not set
@@ -1501,10 +1568,6 @@ CONFIG_MSDOS_PARTITION=y
 # CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_SYSV68_PARTITION is not set
-
-#
-# Native Language Support
-#
 CONFIG_NLS=y
 CONFIG_NLS_DEFAULT="iso8859-1"
 CONFIG_NLS_CODEPAGE_437=y
@@ -1545,10 +1608,6 @@ CONFIG_NLS_ISO8859_1=y
 # CONFIG_NLS_KOI8_R is not set
 # CONFIG_NLS_KOI8_U is not set
 # CONFIG_NLS_UTF8 is not set
-
-#
-# Distributed Lock Manager
-#
 # CONFIG_DLM is not set
 # CONFIG_UCC_SLOW is not set
 
@@ -1561,23 +1620,24 @@ CONFIG_CRC_CCITT=y
 # CONFIG_CRC_ITU_T is not set
 CONFIG_CRC32=y
 # CONFIG_CRC7 is not set
-# CONFIG_LIBCRC32C is not set
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
 CONFIG_PLIST=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
-
-#
-# Instrumentation Support
-#
+CONFIG_INSTRUMENTATION=y
 CONFIG_PROFILING=y
 CONFIG_OPROFILE=y
 # CONFIG_KPROBES is not set
+# CONFIG_MARKERS is not set
 
 #
 # Kernel hacking
 #
 # CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
 CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_MAGIC_SYSRQ=y
 # CONFIG_UNUSED_SYMBOLS is not set
@@ -1586,7 +1646,7 @@ CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_DEBUG_SHIRQ is not set
 CONFIG_DETECT_SOFTLOCKUP=y
-CONFIG_SCHED_DEBUG=y
+# CONFIG_SCHED_DEBUG is not set
 # CONFIG_SCHEDSTATS is not set
 # CONFIG_TIMER_STATS is not set
 # CONFIG_SLUB_DEBUG_ON is not set
@@ -1601,9 +1661,12 @@ CONFIG_DEBUG_BUGVERBOSE=y
 # CONFIG_DEBUG_INFO is not set
 # CONFIG_DEBUG_VM is not set
 # CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
 # CONFIG_FORCED_INLINING is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
 # CONFIG_DEBUG_STACKOVERFLOW is not set
 # CONFIG_DEBUG_STACK_USAGE is not set
 # CONFIG_DEBUG_PAGEALLOC is not set
@@ -1620,6 +1683,7 @@ CONFIG_XMON_DISASSEMBLY=y
 #
 # CONFIG_KEYS is not set
 # CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
 CONFIG_CRYPTO=y
 CONFIG_CRYPTO_ALGAPI=y
 CONFIG_CRYPTO_BLKCIPHER=y
@@ -1628,34 +1692,38 @@ CONFIG_CRYPTO_MANAGER=y
 CONFIG_CRYPTO_HMAC=y
 # CONFIG_CRYPTO_XCBC is not set
 # CONFIG_CRYPTO_NULL is not set
-# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD4=y
 CONFIG_CRYPTO_MD5=y
 CONFIG_CRYPTO_SHA1=y
-# CONFIG_CRYPTO_SHA256 is not set
-# CONFIG_CRYPTO_SHA512 is not set
+CONFIG_CRYPTO_SHA256=y
+CONFIG_CRYPTO_SHA512=y
 # CONFIG_CRYPTO_WP512 is not set
 # CONFIG_CRYPTO_TGR192 is not set
 # CONFIG_CRYPTO_GF128MUL is not set
-CONFIG_CRYPTO_ECB=m
+# CONFIG_CRYPTO_ECB is not set
 CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_PCBC=m
+# CONFIG_CRYPTO_PCBC is not set
 # CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
 # CONFIG_CRYPTO_CRYPTD is not set
 CONFIG_CRYPTO_DES=y
 # CONFIG_CRYPTO_FCRYPT is not set
-# CONFIG_CRYPTO_BLOWFISH is not set
+CONFIG_CRYPTO_BLOWFISH=y
 # CONFIG_CRYPTO_TWOFISH is not set
 # CONFIG_CRYPTO_SERPENT is not set
-# CONFIG_CRYPTO_AES is not set
+CONFIG_CRYPTO_AES=y
 # CONFIG_CRYPTO_CAST5 is not set
 # CONFIG_CRYPTO_CAST6 is not set
 # CONFIG_CRYPTO_TEA is not set
 # CONFIG_CRYPTO_ARC4 is not set
 # CONFIG_CRYPTO_KHAZAD is not set
 # CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_SEED is not set
 # CONFIG_CRYPTO_DEFLATE is not set
 # CONFIG_CRYPTO_MICHAEL_MIC is not set
 # CONFIG_CRYPTO_CRC32C is not set
 # CONFIG_CRYPTO_CAMELLIA is not set
 # CONFIG_CRYPTO_TEST is not set
-# CONFIG_CRYPTO_HW is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+CONFIG_CRYPTO_HW=y
+# CONFIG_PPC_CLOCK is not set
diff --git a/arch/powerpc/configs/ppc64_defconfig b/arch/powerpc/configs/ppc64_defconfig
index 05582af50c5b..3e90c835fe12 100644
--- a/arch/powerpc/configs/ppc64_defconfig
+++ b/arch/powerpc/configs/ppc64_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc4
-# Thu Aug 30 16:47:09 2007
+# Linux kernel version: 2.6.24-rc2
+# Tue Nov  6 23:43:56 2007
 #
 CONFIG_PPC64=y
 
@@ -11,6 +11,7 @@ CONFIG_PPC64=y
 # CONFIG_POWER4_ONLY is not set
 CONFIG_POWER3=y
 CONFIG_POWER4=y
+# CONFIG_TUNE_CELL is not set
 CONFIG_PPC_FPU=y
 CONFIG_ALTIVEC=y
 CONFIG_PPC_STD_MMU=y
@@ -19,8 +20,13 @@ CONFIG_VIRT_CPU_ACCOUNTING=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=32
 CONFIG_64BIT=y
+CONFIG_WORD_SIZE=64
 CONFIG_PPC_MERGE=y
 CONFIG_MMU=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
 CONFIG_GENERIC_HARDIRQS=y
 CONFIG_IRQ_PER_CPU=y
 CONFIG_RWSEM_XCHGADD_ALGORITHM=y
@@ -72,8 +78,15 @@ CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=17
 CONFIG_CGROUPS=y
+# CONFIG_CGROUP_DEBUG is not set
+# CONFIG_CGROUP_NS is not set
+# CONFIG_CGROUP_CPUACCT is not set
 CONFIG_CPUSETS=y
+CONFIG_FAIR_GROUP_SCHED=y
+CONFIG_FAIR_USER_SCHED=y
+# CONFIG_FAIR_CGROUP_SCHED is not set
 CONFIG_SYSFS_DEPRECATED=y
+CONFIG_PROC_PID_CPUSET=y
 CONFIG_RELAY=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_INITRAMFS_SOURCE=""
@@ -93,7 +106,6 @@ CONFIG_FUTEX=y
 CONFIG_ANON_INODES=y
 CONFIG_EPOLL=y
 CONFIG_SIGNALFD=y
-CONFIG_TIMERFD=y
 CONFIG_EVENTFD=y
 CONFIG_SHMEM=y
 CONFIG_VM_EVENT_COUNTERS=y
@@ -114,6 +126,7 @@ CONFIG_STOP_MACHINE=y
 CONFIG_BLOCK=y
 CONFIG_BLK_DEV_IO_TRACE=y
 CONFIG_BLK_DEV_BSG=y
+CONFIG_BLOCK_COMPAT=y
 
 #
 # IO Schedulers
@@ -132,7 +145,6 @@ CONFIG_DEFAULT_IOSCHED="anticipatory"
 # Platform support
 #
 CONFIG_PPC_MULTIPLATFORM=y
-# CONFIG_EMBEDDED6xx is not set
 # CONFIG_PPC_82xx is not set
 # CONFIG_PPC_83xx is not set
 # CONFIG_PPC_86xx is not set
@@ -155,7 +167,15 @@ CONFIG_VIOPATH=y
 CONFIG_PPC_PMAC=y
 CONFIG_PPC_PMAC64=y
 CONFIG_PPC_MAPLE=y
-# CONFIG_PPC_PASEMI is not set
+CONFIG_PPC_PASEMI=y
+
+#
+# PA Semi PWRficient options
+#
+CONFIG_PPC_PASEMI_IOMMU=y
+# CONFIG_PPC_PASEMI_IOMMU_DMA_FORCE is not set
+CONFIG_PPC_PASEMI_MDIO=y
+CONFIG_ELECTRA_IDE=y
 CONFIG_PPC_CELLEB=y
 # CONFIG_PPC_PS3 is not set
 CONFIG_PPC_CELL=y
@@ -188,6 +208,7 @@ CONFIG_RTAS_FLASH=m
 CONFIG_PPC_PMI=m
 CONFIG_MMIO_NVRAM=y
 CONFIG_MPIC_U3_HT_IRQS=y
+CONFIG_MPIC_BROKEN_REGREAD=y
 CONFIG_IBMVIO=y
 # CONFIG_IBMEBUS is not set
 # CONFIG_PPC_MPC106 is not set
@@ -201,6 +222,8 @@ CONFIG_CPU_FREQ_STAT=y
 # CONFIG_CPU_FREQ_STAT_DETAILS is not set
 CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
 # CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
 CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=y
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
@@ -211,6 +234,7 @@ CONFIG_CPU_FREQ_GOV_USERSPACE=y
 # CPU Frequency drivers
 #
 CONFIG_CPU_FREQ_PMAC64=y
+CONFIG_PPC_PASEMI_CPUFREQ=y
 # CONFIG_CPM2 is not set
 CONFIG_AXON_RAM=m
 # CONFIG_FSL_ULI1575 is not set
@@ -254,6 +278,8 @@ CONFIG_SPARSEMEM=y
 CONFIG_HAVE_MEMORY_PRESENT=y
 # CONFIG_SPARSEMEM_STATIC is not set
 CONFIG_SPARSEMEM_EXTREME=y
+CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y
+CONFIG_SPARSEMEM_VMEMMAP=y
 CONFIG_MEMORY_HOTPLUG=y
 CONFIG_MEMORY_HOTPLUG_SPARSE=y
 CONFIG_SPLIT_PTLOCK_CPUS=4
@@ -268,6 +294,7 @@ CONFIG_PROC_DEVICETREE=y
 # CONFIG_CMDLINE_BOOL is not set
 # CONFIG_PM is not set
 CONFIG_SUSPEND_SMP_POSSIBLE=y
+CONFIG_HIBERNATION_SMP_POSSIBLE=y
 CONFIG_SECCOMP=y
 # CONFIG_WANT_DEVICE_TREE is not set
 CONFIG_ISA_DMA_API=y
@@ -284,12 +311,22 @@ CONFIG_PCI_SYSCALL=y
 # CONFIG_PCIEPORTBUS is not set
 CONFIG_ARCH_SUPPORTS_MSI=y
 CONFIG_PCI_MSI=y
+CONFIG_PCI_LEGACY=y
 # CONFIG_PCI_DEBUG is not set
+CONFIG_PCCARD=y
+# CONFIG_PCMCIA_DEBUG is not set
+CONFIG_PCMCIA=y
+CONFIG_PCMCIA_LOAD_CIS=y
+CONFIG_PCMCIA_IOCTL=y
+CONFIG_CARDBUS=y
 
 #
-# PCCARD (PCMCIA/CardBus) support
+# PC-card bridges
 #
-# CONFIG_PCCARD is not set
+# CONFIG_YENTA is not set
+# CONFIG_PD6729 is not set
+# CONFIG_I82092 is not set
+CONFIG_ELECTRA_CF=y
 CONFIG_HOTPLUG_PCI=m
 # CONFIG_HOTPLUG_PCI_FAKE is not set
 # CONFIG_HOTPLUG_PCI_CPCI is not set
@@ -319,7 +356,10 @@ CONFIG_INET=y
 CONFIG_IP_MULTICAST=y
 # CONFIG_IP_ADVANCED_ROUTER is not set
 CONFIG_IP_FIB_HASH=y
-# CONFIG_IP_PNP is not set
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
 CONFIG_NET_IPIP=y
 # CONFIG_NET_IPGRE is not set
 # CONFIG_IP_MROUTE is not set
@@ -333,6 +373,7 @@ CONFIG_INET_TUNNEL=y
 CONFIG_INET_XFRM_MODE_TRANSPORT=y
 CONFIG_INET_XFRM_MODE_TUNNEL=y
 CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
 CONFIG_INET_DIAG=y
 CONFIG_INET_TCP_DIAG=y
 # CONFIG_TCP_CONG_ADVANCED is not set
@@ -404,6 +445,7 @@ CONFIG_NETFILTER_XT_MATCH_STATE=m
 CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
 CONFIG_NETFILTER_XT_MATCH_STRING=m
 CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+# CONFIG_NETFILTER_XT_MATCH_TIME is not set
 CONFIG_NETFILTER_XT_MATCH_U32=m
 CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
 
@@ -465,10 +507,6 @@ CONFIG_LLC=y
 # CONFIG_LAPB is not set
 # CONFIG_ECONET is not set
 # CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
 # CONFIG_NET_SCHED is not set
 CONFIG_NET_CLS_ROUTE=y
 
@@ -498,6 +536,7 @@ CONFIG_NET_CLS_ROUTE=y
 #
 # Generic Driver Options
 #
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_STANDALONE=y
 CONFIG_PREVENT_FIRMWARE_BUILD=y
 CONFIG_FW_LOADER=y
@@ -539,6 +578,8 @@ CONFIG_BLK_DEV_IDE=y
 # CONFIG_BLK_DEV_IDE_SATA is not set
 CONFIG_BLK_DEV_IDEDISK=y
 # CONFIG_IDEDISK_MULTI_MODE is not set
+# CONFIG_BLK_DEV_IDECS is not set
+# CONFIG_BLK_DEV_DELKIN is not set
 CONFIG_BLK_DEV_IDECD=y
 # CONFIG_BLK_DEV_IDETAPE is not set
 # CONFIG_BLK_DEV_IDEFLOPPY is not set
@@ -550,6 +591,11 @@ CONFIG_IDE_PROC_FS=y
 # IDE chipset support/bugfixes
 #
 CONFIG_IDE_GENERIC=y
+# CONFIG_BLK_DEV_PLATFORM is not set
+
+#
+# PCI IDE chipsets support
+#
 CONFIG_BLK_DEV_IDEPCI=y
 CONFIG_IDEPCI_SHARE_IRQ=y
 CONFIG_IDEPCI_PCIBUS_ORDER=y
@@ -557,8 +603,6 @@ CONFIG_IDEPCI_PCIBUS_ORDER=y
 CONFIG_BLK_DEV_GENERIC=y
 # CONFIG_BLK_DEV_OPTI621 is not set
 CONFIG_BLK_DEV_IDEDMA_PCI=y
-# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
-# CONFIG_IDEDMA_ONLYDISK is not set
 # CONFIG_BLK_DEV_AEC62XX is not set
 # CONFIG_BLK_DEV_ALI15X3 is not set
 CONFIG_BLK_DEV_AMD74XX=y
@@ -590,7 +634,7 @@ CONFIG_BLK_DEV_IDE_PMAC_ATA100FIRST=y
 CONFIG_BLK_DEV_IDEDMA_PMAC=y
 # CONFIG_IDE_ARM is not set
 CONFIG_BLK_DEV_IDEDMA=y
-# CONFIG_IDEDMA_IVB is not set
+CONFIG_IDE_ARCH_OBSOLETE_INIT=y
 # CONFIG_BLK_DEV_HD is not set
 
 #
@@ -631,6 +675,7 @@ CONFIG_SCSI_FC_ATTRS=y
 CONFIG_SCSI_ISCSI_ATTRS=m
 # CONFIG_SCSI_SAS_ATTRS is not set
 # CONFIG_SCSI_SAS_LIBSAS is not set
+CONFIG_SCSI_SRP_ATTRS=y
 CONFIG_SCSI_LOWLEVEL=y
 # CONFIG_ISCSI_TCP is not set
 # CONFIG_BLK_DEV_3W_XXXX_RAID is not set
@@ -671,19 +716,20 @@ CONFIG_SCSI_LPFC=m
 # CONFIG_SCSI_DC390T is not set
 CONFIG_SCSI_DEBUG=m
 # CONFIG_SCSI_SRP is not set
+# CONFIG_SCSI_LOWLEVEL_PCMCIA is not set
 CONFIG_ATA=y
 CONFIG_ATA_NONSTANDARD=y
 # CONFIG_SATA_AHCI is not set
 CONFIG_SATA_SVW=y
 # CONFIG_ATA_PIIX is not set
-# CONFIG_SATA_MV is not set
+CONFIG_SATA_MV=y
 # CONFIG_SATA_NV is not set
 # CONFIG_PDC_ADMA is not set
 # CONFIG_SATA_QSTOR is not set
 # CONFIG_SATA_PROMISE is not set
 # CONFIG_SATA_SX4 is not set
 # CONFIG_SATA_SIL is not set
-# CONFIG_SATA_SIL24 is not set
+CONFIG_SATA_SIL24=y
 # CONFIG_SATA_SIS is not set
 # CONFIG_SATA_ULI is not set
 # CONFIG_SATA_VIA is not set
@@ -713,8 +759,10 @@ CONFIG_SATA_SVW=y
 # CONFIG_PATA_OLDPIIX is not set
 # CONFIG_PATA_NETCELL is not set
 # CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_NS87415 is not set
 # CONFIG_PATA_OPTI is not set
 # CONFIG_PATA_OPTIDMA is not set
+CONFIG_PATA_PCMCIA=y
 # CONFIG_PATA_PDC_OLD is not set
 # CONFIG_PATA_RADISYS is not set
 # CONFIG_PATA_RZ1000 is not set
@@ -725,6 +773,7 @@ CONFIG_SATA_SVW=y
 # CONFIG_PATA_SIS is not set
 # CONFIG_PATA_VIA is not set
 CONFIG_PATA_WINBOND=y
+CONFIG_PATA_PLATFORM=y
 CONFIG_PATA_SCC=y
 CONFIG_MD=y
 CONFIG_BLK_DEV_MD=y
@@ -745,15 +794,10 @@ CONFIG_DM_ZERO=m
 CONFIG_DM_MULTIPATH=m
 CONFIG_DM_MULTIPATH_EMC=m
 # CONFIG_DM_MULTIPATH_RDAC is not set
+# CONFIG_DM_MULTIPATH_HP is not set
 # CONFIG_DM_DELAY is not set
-
-#
-# Fusion MPT device support
-#
+# CONFIG_DM_UEVENT is not set
 # CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
-# CONFIG_FUSION_SAS is not set
 
 #
 # IEEE 1394 (FireWire) support
@@ -800,13 +844,15 @@ CONFIG_BONDING=m
 # CONFIG_MACVLAN is not set
 # CONFIG_EQUALIZER is not set
 CONFIG_TUN=m
+# CONFIG_VETH is not set
+# CONFIG_IP1000 is not set
 # CONFIG_ARCNET is not set
-CONFIG_PHYLIB=m
+CONFIG_PHYLIB=y
 
 #
 # MII PHY device drivers
 #
-CONFIG_MARVELL_PHY=m
+CONFIG_MARVELL_PHY=y
 # CONFIG_DAVICOM_PHY is not set
 # CONFIG_QSEMI_PHY is not set
 # CONFIG_LXT_PHY is not set
@@ -818,6 +864,9 @@ CONFIG_BROADCOM_PHY=m
 CONFIG_FIXED_PHY=m
 CONFIG_FIXED_MII_10_FDX=y
 CONFIG_FIXED_MII_100_FDX=y
+# CONFIG_FIXED_MII_1000_FDX is not set
+CONFIG_FIXED_MII_AMNT=1
+# CONFIG_MDIO_BITBANG is not set
 CONFIG_NET_ETHERNET=y
 CONFIG_MII=y
 # CONFIG_HAPPYMEAL is not set
@@ -829,6 +878,11 @@ CONFIG_VORTEX=y
 # CONFIG_NET_TULIP is not set
 # CONFIG_HP100 is not set
 CONFIG_IBMVETH=m
+# CONFIG_IBM_NEW_EMAC is not set
+CONFIG_IBM_NEW_EMAC_ZMII=y
+CONFIG_IBM_NEW_EMAC_RGMII=y
+CONFIG_IBM_NEW_EMAC_TAH=y
+CONFIG_IBM_NEW_EMAC_EMAC4=y
 CONFIG_NET_PCI=y
 CONFIG_PCNET32=y
 # CONFIG_PCNET32_NAPI is not set
@@ -836,7 +890,6 @@ CONFIG_PCNET32=y
 # CONFIG_ADAPTEC_STARFIRE is not set
 # CONFIG_B44 is not set
 # CONFIG_FORCEDETH is not set
-# CONFIG_DGRS is not set
 # CONFIG_EEPRO100 is not set
 CONFIG_E100=y
 # CONFIG_FEALNX is not set
@@ -856,6 +909,7 @@ CONFIG_ACENIC_OMIT_TIGON_I=y
 CONFIG_E1000=y
 # CONFIG_E1000_NAPI is not set
 # CONFIG_E1000_DISABLE_PACKET_SPLIT is not set
+# CONFIG_E1000E is not set
 # CONFIG_NS83820 is not set
 # CONFIG_HAMACHI is not set
 # CONFIG_YELLOWFIN is not set
@@ -863,6 +917,7 @@ CONFIG_E1000=y
 # CONFIG_SIS190 is not set
 # CONFIG_SKGE is not set
 # CONFIG_SKY2 is not set
+# CONFIG_SK98LIN is not set
 # CONFIG_VIA_VELOCITY is not set
 CONFIG_TIGON3=y
 # CONFIG_BNX2 is not set
@@ -872,13 +927,16 @@ CONFIG_SPIDER_NET=m
 CONFIG_NETDEV_10000=y
 # CONFIG_CHELSIO_T1 is not set
 # CONFIG_CHELSIO_T3 is not set
+# CONFIG_IXGBE is not set
 CONFIG_IXGB=m
 # CONFIG_IXGB_NAPI is not set
 # CONFIG_S2IO is not set
 # CONFIG_MYRI10GE is not set
 # CONFIG_NETXEN_NIC is not set
-CONFIG_PASEMI_MAC=m
+# CONFIG_NIU is not set
+CONFIG_PASEMI_MAC=y
 # CONFIG_MLX4_CORE is not set
+# CONFIG_TEHUTI is not set
 CONFIG_TR=y
 CONFIG_IBMOL=y
 # CONFIG_3C359 is not set
@@ -899,6 +957,7 @@ CONFIG_IBMOL=y
 # CONFIG_USB_RTL8150 is not set
 # CONFIG_USB_USBNET_MII is not set
 # CONFIG_USB_USBNET is not set
+# CONFIG_NET_PCMCIA is not set
 # CONFIG_WAN is not set
 CONFIG_ISERIES_VETH=m
 # CONFIG_FDDI is not set
@@ -918,6 +977,7 @@ CONFIG_SLHC=m
 # CONFIG_NET_FC is not set
 # CONFIG_SHAPER is not set
 CONFIG_NETCONSOLE=y
+# CONFIG_NETCONSOLE_DYNAMIC is not set
 CONFIG_NETPOLL=y
 CONFIG_NETPOLL_TRAP=y
 CONFIG_NET_POLL_CONTROLLER=y
@@ -939,7 +999,6 @@ CONFIG_INPUT_MOUSEDEV=y
 CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
 # CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
 CONFIG_INPUT_EVDEV=m
 # CONFIG_INPUT_EVBUG is not set
 
@@ -1002,6 +1061,7 @@ CONFIG_HW_CONSOLE=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_PCI=y
+# CONFIG_SERIAL_8250_CS is not set
 CONFIG_SERIAL_8250_NR_UARTS=4
 CONFIG_SERIAL_8250_RUNTIME_UARTS=4
 # CONFIG_SERIAL_8250_EXTENDED is not set
@@ -1029,14 +1089,18 @@ CONFIG_HVC_RTAS=y
 CONFIG_HVC_BEAT=y
 CONFIG_HVCS=m
 # CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
 # CONFIG_HW_RANDOM is not set
 CONFIG_GEN_RTC=y
 # CONFIG_GEN_RTC_X is not set
 # CONFIG_R3964 is not set
 # CONFIG_APPLICOM is not set
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
+
+#
+# PCMCIA character devices
+#
+# CONFIG_SYNCLINK_CS is not set
+# CONFIG_CARDMAN_4000 is not set
+# CONFIG_CARDMAN_4040 is not set
 CONFIG_RAW_DRIVER=y
 CONFIG_MAX_RAW_DEVS=256
 # CONFIG_HANGCHECK_TIMER is not set
@@ -1068,6 +1132,7 @@ CONFIG_I2C_POWERMAC=y
 # CONFIG_I2C_NFORCE2 is not set
 # CONFIG_I2C_OCORES is not set
 # CONFIG_I2C_PARPORT_LIGHT is not set
+CONFIG_I2C_PASEMI=y
 # CONFIG_I2C_PROSAVAGE is not set
 # CONFIG_I2C_SAVAGE4 is not set
 # CONFIG_I2C_SIMTEC is not set
@@ -1106,6 +1171,13 @@ CONFIG_I2C_POWERMAC=y
 # CONFIG_W1 is not set
 # CONFIG_POWER_SUPPLY is not set
 # CONFIG_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
 
 #
 # Multifunction device drivers
@@ -1122,18 +1194,8 @@ CONFIG_I2C_POWERMAC=y
 #
 # Graphics support
 #
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-
-#
-# Display device support
-#
-CONFIG_DISPLAY_SUPPORT=y
-
-#
-# Display hardware drivers
-#
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
 # CONFIG_VGASTATE is not set
 CONFIG_VIDEO_OUTPUT_CONTROL=m
 CONFIG_FB=y
@@ -1142,6 +1204,7 @@ CONFIG_FB_DDC=y
 CONFIG_FB_CFB_FILLRECT=y
 CONFIG_FB_CFB_COPYAREA=y
 CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
 # CONFIG_FB_SYS_FILLRECT is not set
 # CONFIG_FB_SYS_COPYAREA is not set
 # CONFIG_FB_SYS_IMAGEBLIT is not set
@@ -1192,6 +1255,19 @@ CONFIG_FB_RADEON_BACKLIGHT=y
 # CONFIG_FB_PM3 is not set
 CONFIG_FB_IBM_GXT4500=y
 # CONFIG_FB_VIRTUAL is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_CORGI is not set
+
+#
+# Display device support
+#
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
 
 #
 # Console display driver support
@@ -1332,6 +1408,12 @@ CONFIG_SND_AOA_SOUNDBUS_I2S=m
 # CONFIG_SND_USB_USX2Y is not set
 # CONFIG_SND_USB_CAIAQ is not set
 
+#
+# PCMCIA devices
+#
+# CONFIG_SND_VXPOCKET is not set
+# CONFIG_SND_PDAUDIOCF is not set
+
 #
 # System on Chip audio support
 #
@@ -1348,6 +1430,7 @@ CONFIG_SND_AOA_SOUNDBUS_I2S=m
 CONFIG_HID_SUPPORT=y
 CONFIG_HID=y
 # CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
 
 #
 # USB Input Devices
@@ -1489,19 +1572,53 @@ CONFIG_EDAC=y
 #
 # CONFIG_EDAC_DEBUG is not set
 CONFIG_EDAC_MM_EDAC=y
-# CONFIG_RTC_CLASS is not set
+CONFIG_EDAC_PASEMI=y
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
 
 #
-# DMA Engine support
+# RTC interfaces
 #
-# CONFIG_DMA_ENGINE is not set
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set
+# CONFIG_RTC_DRV_TEST is not set
 
 #
-# DMA Clients
+# I2C RTC drivers
+#
+CONFIG_RTC_DRV_DS1307=y
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+
+#
+# SPI RTC drivers
 #
 
 #
-# DMA Devices
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
 #
 
 #
@@ -1585,7 +1702,6 @@ CONFIG_TMPFS=y
 # CONFIG_TMPFS_POSIX_ACL is not set
 CONFIG_HUGETLBFS=y
 CONFIG_HUGETLB_PAGE=y
-CONFIG_RAMFS=y
 # CONFIG_CONFIGFS_FS is not set
 
 #
@@ -1604,10 +1720,7 @@ CONFIG_CRAMFS=y
 # CONFIG_QNX4FS_FS is not set
 # CONFIG_SYSV_FS is not set
 # CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
+CONFIG_NETWORK_FILESYSTEMS=y
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
@@ -1619,6 +1732,7 @@ CONFIG_NFSD_V3=y
 CONFIG_NFSD_V3_ACL=y
 CONFIG_NFSD_V4=y
 CONFIG_NFSD_TCP=y
+CONFIG_ROOT_NFS=y
 CONFIG_LOCKD=y
 CONFIG_LOCKD_V4=y
 CONFIG_EXPORTFS=m
@@ -1626,6 +1740,7 @@ CONFIG_NFS_ACL_SUPPORT=y
 CONFIG_NFS_COMMON=y
 CONFIG_SUNRPC=y
 CONFIG_SUNRPC_GSS=y
+CONFIG_SUNRPC_XPRT_RDMA=m
 # CONFIG_SUNRPC_BIND34 is not set
 CONFIG_RPCSEC_GSS_KRB5=y
 CONFIG_RPCSEC_GSS_SPKM3=m
@@ -1662,10 +1777,6 @@ CONFIG_MSDOS_PARTITION=y
 # CONFIG_KARMA_PARTITION is not set
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_SYSV68_PARTITION is not set
-
-#
-# Native Language Support
-#
 CONFIG_NLS=y
 CONFIG_NLS_DEFAULT="iso8859-1"
 CONFIG_NLS_CODEPAGE_437=y
@@ -1706,10 +1817,6 @@ CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_KOI8_R=m
 CONFIG_NLS_KOI8_U=m
 CONFIG_NLS_UTF8=m
-
-#
-# Distributed Lock Manager
-#
 # CONFIG_DLM is not set
 # CONFIG_UCC_SLOW is not set
 
@@ -1733,18 +1840,17 @@ CONFIG_PLIST=y
 CONFIG_HAS_IOMEM=y
 CONFIG_HAS_IOPORT=y
 CONFIG_HAS_DMA=y
-
-#
-# Instrumentation Support
-#
+CONFIG_INSTRUMENTATION=y
 CONFIG_PROFILING=y
 CONFIG_OPROFILE=y
 # CONFIG_KPROBES is not set
+# CONFIG_MARKERS is not set
 
 #
 # Kernel hacking
 #
 # CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_WARN_DEPRECATED=y
 CONFIG_ENABLE_MUST_CHECK=y
 CONFIG_MAGIC_SYSRQ=y
 # CONFIG_UNUSED_SYMBOLS is not set
@@ -1768,9 +1874,12 @@ CONFIG_DEBUG_BUGVERBOSE=y
 # CONFIG_DEBUG_INFO is not set
 # CONFIG_DEBUG_VM is not set
 # CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
 CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
 # CONFIG_RCU_TORTURE_TEST is not set
 # CONFIG_FAULT_INJECTION is not set
+# CONFIG_SAMPLES is not set
 CONFIG_DEBUG_STACKOVERFLOW=y
 CONFIG_DEBUG_STACK_USAGE=y
 # CONFIG_DEBUG_PAGEALLOC is not set
@@ -1780,6 +1889,7 @@ CONFIG_XMON=y
 # CONFIG_XMON_DEFAULT is not set
 CONFIG_XMON_DISASSEMBLY=y
 CONFIG_IRQSTACKS=y
+# CONFIG_VIRQ_DEBUG is not set
 CONFIG_BOOTX_TEXT=y
 # CONFIG_PPC_EARLY_DEBUG is not set
 
@@ -1788,6 +1898,7 @@ CONFIG_BOOTX_TEXT=y
 #
 # CONFIG_KEYS is not set
 # CONFIG_SECURITY is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
 CONFIG_XOR_BLOCKS=y
 CONFIG_ASYNC_CORE=y
 CONFIG_ASYNC_MEMCPY=y
@@ -1812,6 +1923,7 @@ CONFIG_CRYPTO_ECB=m
 CONFIG_CRYPTO_CBC=y
 CONFIG_CRYPTO_PCBC=m
 # CONFIG_CRYPTO_LRW is not set
+# CONFIG_CRYPTO_XTS is not set
 # CONFIG_CRYPTO_CRYPTD is not set
 CONFIG_CRYPTO_DES=y
 # CONFIG_CRYPTO_FCRYPT is not set
@@ -1826,9 +1938,12 @@ CONFIG_CRYPTO_TEA=m
 CONFIG_CRYPTO_ARC4=m
 CONFIG_CRYPTO_KHAZAD=m
 CONFIG_CRYPTO_ANUBIS=m
+# CONFIG_CRYPTO_SEED is not set
 CONFIG_CRYPTO_DEFLATE=m
 CONFIG_CRYPTO_MICHAEL_MIC=m
 CONFIG_CRYPTO_CRC32C=m
 # CONFIG_CRYPTO_CAMELLIA is not set
 CONFIG_CRYPTO_TEST=m
+# CONFIG_CRYPTO_AUTHENC is not set
 # CONFIG_CRYPTO_HW is not set
+# CONFIG_PPC_CLOCK is not set
diff --git a/arch/powerpc/kernel/cputable.c b/arch/powerpc/kernel/cputable.c
index d3fb7d0c6c1c..9ed351f3c966 100644
--- a/arch/powerpc/kernel/cputable.c
+++ b/arch/powerpc/kernel/cputable.c
@@ -1104,6 +1104,16 @@ static struct cpu_spec __initdata cpu_specs[] = {
 	{
 		.pvr_mask		= 0xf0000fff,
 		.pvr_value		= 0x40000850,
+		.cpu_name		= "440GR Rev. A",
+		.cpu_features		= CPU_FTRS_44X,
+		.cpu_user_features	= COMMON_USER_BOOKE,
+		.icache_bsize		= 32,
+		.dcache_bsize		= 32,
+		.platform		= "ppc440",
+	},
+	{ /* Use logical PVR for 440EP (logical pvr = pvr | 0x8) */
+		.pvr_mask		= 0xf0000fff,
+		.pvr_value		= 0x40000858,
 		.cpu_name		= "440EP Rev. A",
 		.cpu_features		= CPU_FTRS_44X,
 		.cpu_user_features	= COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
@@ -1115,6 +1125,16 @@ static struct cpu_spec __initdata cpu_specs[] = {
 	{
 		.pvr_mask		= 0xf0000fff,
 		.pvr_value		= 0x400008d3,
+		.cpu_name		= "440GR Rev. B",
+		.cpu_features		= CPU_FTRS_44X,
+		.cpu_user_features	= COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
+		.icache_bsize		= 32,
+		.dcache_bsize		= 32,
+		.platform		= "ppc440",
+	},
+	{ /* Use logical PVR for 440EP (logical pvr = pvr | 0x8) */
+		.pvr_mask		= 0xf0000fff,
+		.pvr_value		= 0x400008db,
 		.cpu_name		= "440EP Rev. B",
 		.cpu_features		= CPU_FTRS_44X,
 		.cpu_user_features	= COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
@@ -1123,20 +1143,9 @@ static struct cpu_spec __initdata cpu_specs[] = {
 		.cpu_setup		= __setup_cpu_440ep,
 		.platform		= "ppc440",
 	},
-	{ /* 440EPX */
-		.pvr_mask		= 0xf0000ffb,
-		.pvr_value		= 0x200008D0,
-		.cpu_name		= "440EPX",
-		.cpu_features		= CPU_FTRS_44X,
-		.cpu_user_features	= COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
-		.icache_bsize		= 32,
-		.dcache_bsize		= 32,
-		.cpu_setup		= __setup_cpu_440epx,
-		.platform		= "ppc440",
-	},
 	{ /* 440GRX */
 		.pvr_mask		= 0xf0000ffb,
-		.pvr_value		= 0x200008D8,
+		.pvr_value		= 0x200008D0,
 		.cpu_name		= "440GRX",
 		.cpu_features		= CPU_FTRS_44X,
 		.cpu_user_features	= COMMON_USER_BOOKE,
@@ -1145,6 +1154,17 @@ static struct cpu_spec __initdata cpu_specs[] = {
 		.cpu_setup		= __setup_cpu_440grx,
 		.platform		= "ppc440",
 	},
+	{ /* Use logical PVR for 440EPx (logical pvr = pvr | 0x8) */
+		.pvr_mask		= 0xf0000ffb,
+		.pvr_value		= 0x200008D8,
+		.cpu_name		= "440EPX",
+		.cpu_features		= CPU_FTRS_44X,
+		.cpu_user_features	= COMMON_USER_BOOKE | PPC_FEATURE_HAS_FPU,
+		.icache_bsize		= 32,
+		.dcache_bsize		= 32,
+		.cpu_setup		= __setup_cpu_440epx,
+		.platform		= "ppc440",
+	},
 	{	/* 440GP Rev. B */
 		.pvr_mask		= 0xf0000fff,
 		.pvr_value		= 0x40000440,
diff --git a/arch/powerpc/kernel/entry_32.S b/arch/powerpc/kernel/entry_32.S
index 21d889e63e87..a7572cf464bd 100644
--- a/arch/powerpc/kernel/entry_32.S
+++ b/arch/powerpc/kernel/entry_32.S
@@ -244,6 +244,13 @@ syscall_exit_cont:
 	andis.	r10,r0,DBCR0_IC@h
 	bnel-	load_dbcr0
 #endif
+#ifdef CONFIG_44x
+	lis	r4,icache_44x_need_flush@ha
+	lwz	r5,icache_44x_need_flush@l(r4)
+	cmplwi	cr0,r5,0
+	bne-	2f
+1:
+#endif /* CONFIG_44x */
 	stwcx.	r0,0,r1			/* to clear the reservation */
 	lwz	r4,_LINK(r1)
 	lwz	r5,_CCR(r1)
@@ -258,6 +265,12 @@ syscall_exit_cont:
 	mtspr	SPRN_SRR1,r8
 	SYNC
 	RFI
+#ifdef CONFIG_44x
+2:	li	r7,0
+	iccci	r0,r0
+	stw	r7,icache_44x_need_flush@l(r4)
+	b	1b
+#endif  /* CONFIG_44x */
 
 66:	li	r3,-ENOSYS
 	b	ret_from_syscall
@@ -683,6 +696,16 @@ resume_kernel:
 
 	/* interrupts are hard-disabled at this point */
 restore:
+#ifdef CONFIG_44x
+	lis	r4,icache_44x_need_flush@ha
+	lwz	r5,icache_44x_need_flush@l(r4)
+	cmplwi	cr0,r5,0
+	beq+	1f
+	li	r6,0
+	iccci	r0,r0
+	stw	r6,icache_44x_need_flush@l(r4)
+1:
+#endif  /* CONFIG_44x */
 	lwz	r0,GPR0(r1)
 	lwz	r2,GPR2(r1)
 	REST_4GPRS(3, r1)
diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S
index 97c5857faf00..c34986835a4e 100644
--- a/arch/powerpc/kernel/head_64.S
+++ b/arch/powerpc/kernel/head_64.S
@@ -904,7 +904,7 @@ handle_page_fault:
  */
 12:	bl	.save_nvgprs
 	addi	r3,r1,STACK_FRAME_OVERHEAD
-	lwz	r4,_DAR(r1)
+	ld	r4,_DAR(r1)
 	bl	.low_hash_fault
 	b	.ret_from_except
 
diff --git a/arch/powerpc/kernel/idle.c b/arch/powerpc/kernel/idle.c
index abd2957fe537..c3cf0e8f3ac1 100644
--- a/arch/powerpc/kernel/idle.c
+++ b/arch/powerpc/kernel/idle.c
@@ -122,7 +122,7 @@ static ctl_table powersave_nap_sysctl_root[] = {
 	{
 		.ctl_name	= CTL_KERN,
 		.procname	= "kernel",
-		.mode		= 0755,
+		.mode		= 0555,
 		.child		= powersave_nap_ctl_table,
 	},
 	{}
diff --git a/arch/powerpc/kernel/misc_32.S b/arch/powerpc/kernel/misc_32.S
index 8533de50347d..8b642ab26d37 100644
--- a/arch/powerpc/kernel/misc_32.S
+++ b/arch/powerpc/kernel/misc_32.S
@@ -288,7 +288,16 @@ _GLOBAL(_tlbia)
  */
 _GLOBAL(_tlbie)
 #if defined(CONFIG_40x)
+	/* We run the search with interrupts disabled because we have to change
+	 * the PID and I don't want to preempt when that happens.
+	 */
+	mfmsr	r5
+	mfspr	r6,SPRN_PID
+	wrteei	0
+	mtspr	SPRN_PID,r4
 	tlbsx.	r3, 0, r3
+	mtspr	SPRN_PID,r6
+	wrtee	r5
 	bne	10f
 	sync
 	/* There are only 64 TLB entries, so r3 < 64, which means bit 25 is clear.
@@ -297,23 +306,23 @@ _GLOBAL(_tlbie)
 	tlbwe	r3, r3, TLB_TAG
 	isync
 10:
+
 #elif defined(CONFIG_44x)
-	mfspr	r4,SPRN_MMUCR
-	mfspr	r5,SPRN_PID			/* Get PID */
-	rlwimi	r4,r5,0,24,31			/* Set TID */
+	mfspr	r5,SPRN_MMUCR
+	rlwimi	r5,r4,0,24,31			/* Set TID */
 
 	/* We have to run the search with interrupts disabled, even critical
 	 * and debug interrupts (in fact the only critical exceptions we have
 	 * are debug and machine check).  Otherwise  an interrupt which causes
 	 * a TLB miss can clobber the MMUCR between the mtspr and the tlbsx. */
-	mfmsr	r5
+	mfmsr	r4
 	lis	r6,(MSR_EE|MSR_CE|MSR_ME|MSR_DE)@ha
 	addi	r6,r6,(MSR_EE|MSR_CE|MSR_ME|MSR_DE)@l
-	andc	r6,r5,r6
+	andc	r6,r4,r6
 	mtmsr	r6
-	mtspr	SPRN_MMUCR,r4
+	mtspr	SPRN_MMUCR,r5
 	tlbsx.	r3, 0, r3
-	mtmsr	r5
+	mtmsr	r4
 	bne	10f
 	sync
 	/* There are only 64 TLB entries, so r3 < 64,
@@ -534,12 +543,21 @@ END_FTR_SECTION_IFSET(CPU_FTR_COHERENT_ICACHE)
 	addi	r3,r3,L1_CACHE_BYTES
 	bdnz	0b
 	sync
+#ifndef CONFIG_44x
+	/* We don't flush the icache on 44x. Those have a virtual icache
+	 * and we don't have access to the virtual address here (it's
+	 * not the page vaddr but where it's mapped in user space). The
+	 * flushing of the icache on these is handled elsewhere, when
+	 * a change in the address space occurs, before returning to
+	 * user space
+	 */
 	mtctr	r4
 1:	icbi	0,r6
 	addi	r6,r6,L1_CACHE_BYTES
 	bdnz	1b
 	sync
 	isync
+#endif /* CONFIG_44x */
 	blr
 
 /*
diff --git a/arch/powerpc/kernel/prom.c b/arch/powerpc/kernel/prom.c
index 9f329a8928ea..acc0d247d3c3 100644
--- a/arch/powerpc/kernel/prom.c
+++ b/arch/powerpc/kernel/prom.c
@@ -697,6 +697,18 @@ static int __init early_init_dt_scan_cpus(unsigned long node,
 		prop = of_get_flat_dt_prop(node, "cpu-version", NULL);
 		if (prop && (*prop & 0xff000000) == 0x0f000000)
 			identify_cpu(0, *prop);
+#if defined(CONFIG_44x) && defined(CONFIG_PPC_FPU)
+		/*
+		 * Since 440GR(x)/440EP(x) processors have the same pvr,
+		 * we check the node path and set bit 28 in the cur_cpu_spec
+		 * pvr for EP(x) processor version. This bit is always 0 in
+		 * the "real" pvr. Then we call identify_cpu again with
+		 * the new logical pvr to enable FPU support.
+		 */
+		if (strstr(uname, "440EP")) {
+			identify_cpu(0, cur_cpu_spec->pvr_value | 0x8);
+		}
+#endif
 	}
 
 	check_cpu_feature_properties(node);
diff --git a/arch/powerpc/kernel/prom_init.c b/arch/powerpc/kernel/prom_init.c
index 1db10f70ae69..1add6efdb315 100644
--- a/arch/powerpc/kernel/prom_init.c
+++ b/arch/powerpc/kernel/prom_init.c
@@ -1244,7 +1244,7 @@ static void __init prom_initialize_tce_table(void)
 			local_alloc_bottom = base;
 
 		/* It seems OF doesn't null-terminate the path :-( */
-		memset(path, 0, sizeof(path));
+		memset(path, 0, PROM_SCRATCH_SIZE);
 		/* Call OF to setup the TCE hardware */
 		if (call_prom("package-to-path", 3, 1, node,
 			      path, PROM_SCRATCH_SIZE-1) == PROM_ERROR) {
diff --git a/arch/powerpc/kernel/setup_64.c b/arch/powerpc/kernel/setup_64.c
index ede77dbbd4df..3b1529c103ef 100644
--- a/arch/powerpc/kernel/setup_64.c
+++ b/arch/powerpc/kernel/setup_64.c
@@ -291,23 +291,16 @@ static void __init initialize_cache_info(void)
 		if ( num_cpus == 1 ) {
 			const u32 *sizep, *lsizep;
 			u32 size, lsize;
-			const char *dc, *ic;
-
-			/* Then read cache informations */
-			if (machine_is(powermac)) {
-				dc = "d-cache-block-size";
-				ic = "i-cache-block-size";
-			} else {
-				dc = "d-cache-line-size";
-				ic = "i-cache-line-size";
-			}
 
 			size = 0;
 			lsize = cur_cpu_spec->dcache_bsize;
 			sizep = of_get_property(np, "d-cache-size", NULL);
 			if (sizep != NULL)
 				size = *sizep;
-			lsizep = of_get_property(np, dc, NULL);
+			lsizep = of_get_property(np, "d-cache-block-size", NULL);
+			/* fallback if block size missing */
+			if (lsizep == NULL)
+				lsizep = of_get_property(np, "d-cache-line-size", NULL);
 			if (lsizep != NULL)
 				lsize = *lsizep;
 			if (sizep == 0 || lsizep == 0)
@@ -324,7 +317,9 @@ static void __init initialize_cache_info(void)
 			sizep = of_get_property(np, "i-cache-size", NULL);
 			if (sizep != NULL)
 				size = *sizep;
-			lsizep = of_get_property(np, ic, NULL);
+			lsizep = of_get_property(np, "i-cache-block-size", NULL);
+			if (lsizep == NULL)
+				lsizep = of_get_property(np, "i-cache-line-size", NULL);
 			if (lsizep != NULL)
 				lsize = *lsizep;
 			if (sizep == 0 || lsizep == 0)
diff --git a/arch/powerpc/kernel/swsusp_32.S b/arch/powerpc/kernel/swsusp_32.S
index 69e8f86aa4f8..77fc76607ab2 100644
--- a/arch/powerpc/kernel/swsusp_32.S
+++ b/arch/powerpc/kernel/swsusp_32.S
@@ -133,10 +133,12 @@ _GLOBAL(swsusp_arch_suspend)
 /* Resume code */
 _GLOBAL(swsusp_arch_resume)
 
+#ifdef CONFIG_ALTIVEC
 	/* Stop pending alitvec streams and memory accesses */
 BEGIN_FTR_SECTION
 	DSSALL
 END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC)
+#endif
  	sync
 
 	/* Disable MSR:DR to make sure we don't take a TLB or
diff --git a/arch/powerpc/kernel/time.c b/arch/powerpc/kernel/time.c
index 9eb3284deac4..99ebcd3884d2 100644
--- a/arch/powerpc/kernel/time.c
+++ b/arch/powerpc/kernel/time.c
@@ -586,7 +586,7 @@ void timer_interrupt(struct pt_regs * regs)
 		/* not time for this event yet */
 		now = per_cpu(decrementer_next_tb, cpu) - now;
 		if (now <= DECREMENTER_MAX)
-			set_dec((unsigned int)now - 1);
+			set_dec((int)now);
 		return;
 	}
 	old_regs = set_irq_regs(regs);
@@ -611,8 +611,6 @@ void timer_interrupt(struct pt_regs * regs)
 
 	if (evt->event_handler)
 		evt->event_handler(evt);
-	else
-		evt->set_next_event(DECREMENTER_MAX, evt);
 
 #ifdef CONFIG_PPC_ISERIES
 	if (firmware_has_feature(FW_FEATURE_ISERIES) && hvlpevent_is_pending())
@@ -836,9 +834,6 @@ static int decrementer_set_next_event(unsigned long evt,
 				      struct clock_event_device *dev)
 {
 	__get_cpu_var(decrementer_next_tb) = get_tb_or_rtc() + evt;
-	/* The decrementer interrupts on the 0 -> -1 transition */
-	if (evt)
-		--evt;
 	set_dec(evt);
 	return 0;
 }
@@ -871,7 +866,8 @@ void init_decrementer_clockevent(void)
 					     decrementer_clockevent.shift);
 	decrementer_clockevent.max_delta_ns =
 		clockevent_delta2ns(DECREMENTER_MAX, &decrementer_clockevent);
-	decrementer_clockevent.min_delta_ns = 1000;
+	decrementer_clockevent.min_delta_ns =
+		clockevent_delta2ns(2, &decrementer_clockevent);
 
 	register_decrementer_clockevent(cpu);
 }
diff --git a/arch/powerpc/kernel/vmlinux.lds.S b/arch/powerpc/kernel/vmlinux.lds.S
index 823a8cbd60b5..f66fa5d966b0 100644
--- a/arch/powerpc/kernel/vmlinux.lds.S
+++ b/arch/powerpc/kernel/vmlinux.lds.S
@@ -37,11 +37,10 @@ SECTIONS
 		ALIGN_FUNCTION();
 		*(.text.head)
 		_text = .;
-		TEXT_TEXT
+		*(.text .fixup .text.init.refok .exit.text.refok)
 		SCHED_TEXT
 		LOCK_TEXT
 		KPROBES_TEXT
-		*(.fixup)
 
 #ifdef CONFIG_PPC32
 		*(.got1)
diff --git a/arch/powerpc/mm/40x_mmu.c b/arch/powerpc/mm/40x_mmu.c
index e067df836be2..3899ea97fbdf 100644
--- a/arch/powerpc/mm/40x_mmu.c
+++ b/arch/powerpc/mm/40x_mmu.c
@@ -98,13 +98,12 @@ unsigned long __init mmu_mapin_ram(void)
 
 	v = KERNELBASE;
 	p = PPC_MEMSTART;
-	s = 0;
+	s = total_lowmem;
 
-	if (__map_without_ltlbs) {
-		return s;
-	}
+	if (__map_without_ltlbs)
+		return 0;
 
-	while (s <= (total_lowmem - LARGE_PAGE_SIZE_16M)) {
+	while (s >= LARGE_PAGE_SIZE_16M) {
 		pmd_t *pmdp;
 		unsigned long val = p | _PMD_SIZE_16M | _PAGE_HWEXEC | _PAGE_HWWRITE;
 
@@ -116,10 +115,10 @@ unsigned long __init mmu_mapin_ram(void)
 
 		v += LARGE_PAGE_SIZE_16M;
 		p += LARGE_PAGE_SIZE_16M;
-		s += LARGE_PAGE_SIZE_16M;
+		s -= LARGE_PAGE_SIZE_16M;
 	}
 
-	while (s <= (total_lowmem - LARGE_PAGE_SIZE_4M)) {
+	while (s >= LARGE_PAGE_SIZE_4M) {
 		pmd_t *pmdp;
 		unsigned long val = p | _PMD_SIZE_4M | _PAGE_HWEXEC | _PAGE_HWWRITE;
 
@@ -128,8 +127,8 @@ unsigned long __init mmu_mapin_ram(void)
 
 		v += LARGE_PAGE_SIZE_4M;
 		p += LARGE_PAGE_SIZE_4M;
-		s += LARGE_PAGE_SIZE_4M;
+		s -= LARGE_PAGE_SIZE_4M;
 	}
 
-	return s;
+	return total_lowmem - s;
 }
diff --git a/arch/powerpc/mm/44x_mmu.c b/arch/powerpc/mm/44x_mmu.c
index c3df50476539..04dc08798d3d 100644
--- a/arch/powerpc/mm/44x_mmu.c
+++ b/arch/powerpc/mm/44x_mmu.c
@@ -35,6 +35,7 @@
  */
 unsigned int tlb_44x_index; /* = 0 */
 unsigned int tlb_44x_hwater = PPC44x_TLB_SIZE - 1 - PPC44x_EARLY_TLBS;
+int icache_44x_need_flush;
 
 /*
  * "Pins" a 256MB TLB entry in AS0 for kernel lowmem
diff --git a/arch/powerpc/mm/fault.c b/arch/powerpc/mm/fault.c
index a18fda361cc0..8135da06e0a4 100644
--- a/arch/powerpc/mm/fault.c
+++ b/arch/powerpc/mm/fault.c
@@ -309,7 +309,7 @@ good_area:
 					set_bit(PG_arch_1, &page->flags);
 				}
 				pte_update(ptep, 0, _PAGE_HWEXEC);
-				_tlbie(address);
+				_tlbie(address, mm->context.id);
 				pte_unmap_unlock(ptep, ptl);
 				up_read(&mm->mmap_sem);
 				return 0;
diff --git a/arch/powerpc/mm/hash_low_64.S b/arch/powerpc/mm/hash_low_64.S
index ad253b959030..e935edd6b72b 100644
--- a/arch/powerpc/mm/hash_low_64.S
+++ b/arch/powerpc/mm/hash_low_64.S
@@ -331,7 +331,7 @@ htab_pte_insert_failure:
  *****************************************************************************/
 
 /* _hash_page_4K(unsigned long ea, unsigned long access, unsigned long vsid,
- *		 pte_t *ptep, unsigned long trap, int local)
+ *		 pte_t *ptep, unsigned long trap, int local, int ssize)
  */
 
 /*
@@ -557,7 +557,8 @@ htab_inval_old_hpte:
 	mr	r4,r31			/* PTE.pte */
 	li	r5,0			/* PTE.hidx */
 	li	r6,MMU_PAGE_64K		/* psize */
-	ld	r7,STK_PARM(r8)(r1)	/* local */
+	ld	r7,STK_PARM(r9)(r1)	/* ssize */
+	ld	r8,STK_PARM(r8)(r1)	/* local */
 	bl	.flush_hash_page
 	b	htab_insert_pte
 	
diff --git a/arch/powerpc/mm/hash_utils_64.c b/arch/powerpc/mm/hash_utils_64.c
index c78dc912411f..f09730bf3a33 100644
--- a/arch/powerpc/mm/hash_utils_64.c
+++ b/arch/powerpc/mm/hash_utils_64.c
@@ -51,6 +51,7 @@
 #include <asm/cputable.h>
 #include <asm/sections.h>
 #include <asm/spu.h>
+#include <asm/udbg.h>
 
 #ifdef DEBUG
 #define DBG(fmt...) udbg_printf(fmt)
@@ -791,8 +792,7 @@ int hash_page(unsigned long ea, unsigned long access, unsigned long trap)
 	}
 	if (user_region) {
 		if (psize != get_paca()->context.user_psize) {
-			get_paca()->context.user_psize =
-				mm->context.user_psize;
+			get_paca()->context = mm->context;
 			slb_flush_and_rebolt();
 		}
 	} else if (get_paca()->vmalloc_sllp !=
@@ -885,6 +885,9 @@ void hash_preload(struct mm_struct *mm, unsigned long ea,
 	local_irq_restore(flags);
 }
 
+/* WARNING: This is called from hash_low_64.S, if you change this prototype,
+ *          do not forget to update the assembly call site !
+ */
 void flush_hash_page(unsigned long va, real_pte_t pte, int psize, int ssize,
 		     int local)
 {
diff --git a/arch/powerpc/mm/mmu_decl.h b/arch/powerpc/mm/mmu_decl.h
index c94a64fd3c01..eb3a732e91db 100644
--- a/arch/powerpc/mm/mmu_decl.h
+++ b/arch/powerpc/mm/mmu_decl.h
@@ -61,12 +61,12 @@ extern unsigned long total_lowmem;
 #define mmu_mapin_ram()		(0UL)
 
 #elif defined(CONFIG_4xx)
-#define flush_HPTE(X, va, pg)	_tlbie(va)
+#define flush_HPTE(pid, va, pg)	_tlbie(va, pid)
 extern void MMU_init_hw(void);
 extern unsigned long mmu_mapin_ram(void);
 
 #elif defined(CONFIG_FSL_BOOKE)
-#define flush_HPTE(X, va, pg)	_tlbie(va)
+#define flush_HPTE(pid, va, pg)	_tlbie(va, pid)
 extern void MMU_init_hw(void);
 extern unsigned long mmu_mapin_ram(void);
 extern void adjust_total_lowmem(void);
diff --git a/arch/powerpc/mm/slb.c b/arch/powerpc/mm/slb.c
index bbd2c512ee05..27922dff8b94 100644
--- a/arch/powerpc/mm/slb.c
+++ b/arch/powerpc/mm/slb.c
@@ -25,6 +25,7 @@
 #include <asm/smp.h>
 #include <asm/firmware.h>
 #include <linux/compiler.h>
+#include <asm/udbg.h>
 
 #ifdef DEBUG
 #define DBG(fmt...) udbg_printf(fmt)
@@ -148,6 +149,35 @@ void slb_vmalloc_update(void)
 	slb_flush_and_rebolt();
 }
 
+/* Helper function to compare esids.  There are four cases to handle.
+ * 1. The system is not 1T segment size capable.  Use the GET_ESID compare.
+ * 2. The system is 1T capable, both addresses are < 1T, use the GET_ESID compare.
+ * 3. The system is 1T capable, only one of the two addresses is > 1T.  This is not a match.
+ * 4. The system is 1T capable, both addresses are > 1T, use the GET_ESID_1T macro to compare.
+ */
+static inline int esids_match(unsigned long addr1, unsigned long addr2)
+{
+	int esid_1t_count;
+
+	/* System is not 1T segment size capable. */
+	if (!cpu_has_feature(CPU_FTR_1T_SEGMENT))
+		return (GET_ESID(addr1) == GET_ESID(addr2));
+
+	esid_1t_count = (((addr1 >> SID_SHIFT_1T) != 0) +
+				((addr2 >> SID_SHIFT_1T) != 0));
+
+	/* both addresses are < 1T */
+	if (esid_1t_count == 0)
+		return (GET_ESID(addr1) == GET_ESID(addr2));
+
+	/* One address < 1T, the other > 1T.  Not a match */
+	if (esid_1t_count == 1)
+		return 0;
+
+	/* Both addresses are > 1T. */
+	return (GET_ESID_1T(addr1) == GET_ESID_1T(addr2));
+}
+
 /* Flush all user entries from the segment table of the current processor. */
 void switch_slb(struct task_struct *tsk, struct mm_struct *mm)
 {
@@ -193,15 +223,14 @@ void switch_slb(struct task_struct *tsk, struct mm_struct *mm)
 		return;
 	slb_allocate(pc);
 
-	if (GET_ESID(pc) == GET_ESID(stack))
+	if (esids_match(pc,stack))
 		return;
 
 	if (is_kernel_addr(stack))
 		return;
 	slb_allocate(stack);
 
-	if ((GET_ESID(pc) == GET_ESID(unmapped_base))
-	    || (GET_ESID(stack) == GET_ESID(unmapped_base)))
+	if (esids_match(pc,unmapped_base) || esids_match(stack,unmapped_base))
 		return;
 
 	if (is_kernel_addr(unmapped_base))
diff --git a/arch/powerpc/platforms/cell/interrupt.c b/arch/powerpc/platforms/cell/interrupt.c
index 151fd8b82d63..04f74f9f9ab6 100644
--- a/arch/powerpc/platforms/cell/interrupt.c
+++ b/arch/powerpc/platforms/cell/interrupt.c
@@ -158,6 +158,18 @@ static unsigned int iic_get_irq(void)
 	return virq;
 }
 
+void iic_setup_cpu(void)
+{
+	out_be64(&__get_cpu_var(iic).regs->prio, 0xff);
+}
+
+u8 iic_get_target_id(int cpu)
+{
+	return per_cpu(iic, cpu).target_id;
+}
+
+EXPORT_SYMBOL_GPL(iic_get_target_id);
+
 #ifdef CONFIG_SMP
 
 /* Use the highest interrupt priorities for IPI */
@@ -166,29 +178,17 @@ static inline int iic_ipi_to_irq(int ipi)
 	return IIC_IRQ_TYPE_IPI + 0xf - ipi;
 }
 
-void iic_setup_cpu(void)
-{
-	out_be64(&__get_cpu_var(iic).regs->prio, 0xff);
-}
-
 void iic_cause_IPI(int cpu, int mesg)
 {
 	out_be64(&per_cpu(iic, cpu).regs->generate, (0xf - mesg) << 4);
 }
 
-u8 iic_get_target_id(int cpu)
-{
-	return per_cpu(iic, cpu).target_id;
-}
-EXPORT_SYMBOL_GPL(iic_get_target_id);
-
 struct irq_host *iic_get_irq_host(int node)
 {
 	return iic_host;
 }
 EXPORT_SYMBOL_GPL(iic_get_irq_host);
 
-
 static irqreturn_t iic_ipi_action(int irq, void *dev_id)
 {
 	int ipi = (int)(long)dev_id;
diff --git a/arch/powerpc/platforms/cell/smp.c b/arch/powerpc/platforms/cell/smp.c
index 1c0acbad7425..e4438456c867 100644
--- a/arch/powerpc/platforms/cell/smp.c
+++ b/arch/powerpc/platforms/cell/smp.c
@@ -44,6 +44,7 @@
 #include <asm/rtas.h>
 
 #include "interrupt.h"
+#include <asm/udbg.h>
 
 #ifdef DEBUG
 #define DBG(fmt...) udbg_printf(fmt)
diff --git a/arch/powerpc/platforms/celleb/setup.c b/arch/powerpc/platforms/celleb/setup.c
index 1769d755eff3..ddfb35ae741f 100644
--- a/arch/powerpc/platforms/celleb/setup.c
+++ b/arch/powerpc/platforms/celleb/setup.c
@@ -49,6 +49,7 @@
 #include <asm/machdep.h>
 #include <asm/cputable.h>
 #include <asm/irq.h>
+#include <asm/time.h>
 #include <asm/spu_priv1.h>
 #include <asm/firmware.h>
 #include <asm/of_platform.h>
diff --git a/arch/powerpc/platforms/iseries/irq.h b/arch/powerpc/platforms/iseries/irq.h
index 69f1b437fc7b..a1c236074034 100644
--- a/arch/powerpc/platforms/iseries/irq.h
+++ b/arch/powerpc/platforms/iseries/irq.h
@@ -1,9 +1,13 @@
 #ifndef	_ISERIES_IRQ_H
 #define	_ISERIES_IRQ_H
 
+#ifdef CONFIG_PCI
 extern void iSeries_init_IRQ(void);
 extern int  iSeries_allocate_IRQ(HvBusNumber, HvSubBusNumber, u32);
 extern void iSeries_activate_IRQs(void);
+#else
+#define iSeries_init_IRQ	NULL
+#endif
 extern unsigned int iSeries_get_irq(void);
 
 #endif /* _ISERIES_IRQ_H */
diff --git a/arch/powerpc/platforms/iseries/setup.c b/arch/powerpc/platforms/iseries/setup.c
index 37ae07ee54a9..0877a8834110 100644
--- a/arch/powerpc/platforms/iseries/setup.c
+++ b/arch/powerpc/platforms/iseries/setup.c
@@ -617,10 +617,6 @@ static void iseries_dedicated_idle(void)
 	}
 }
 
-#ifndef CONFIG_PCI
-void __init iSeries_init_IRQ(void) { }
-#endif
-
 static void __iomem *iseries_ioremap(phys_addr_t address, unsigned long size,
 				     unsigned long flags)
 {
diff --git a/arch/powerpc/platforms/iseries/vio.c b/arch/powerpc/platforms/iseries/vio.c
index d6435b03971f..be06cfd9fa3d 100644
--- a/arch/powerpc/platforms/iseries/vio.c
+++ b/arch/powerpc/platforms/iseries/vio.c
@@ -523,15 +523,16 @@ static void __init get_viotape_info(struct device_node *vio_root)
 static int __init iseries_vio_init(void)
 {
 	struct device_node *vio_root;
+	int ret = -ENODEV;
 
 	if (!firmware_has_feature(FW_FEATURE_ISERIES))
-		return -ENODEV;
+		goto out;
 
 	iommu_vio_init();
 
 	vio_root = of_find_node_by_path("/vdevice");
 	if (!vio_root)
-		return -ENODEV;
+		goto out;
 
 	if (viopath_hostLp == HvLpIndexInvalid) {
 		vio_set_hostlp();
@@ -544,10 +545,11 @@ static int __init iseries_vio_init(void)
 	get_viocd_info(vio_root);
 	get_viotape_info(vio_root);
 
-	return 0;
+	ret = 0;
 
  put_node:
 	of_node_put(vio_root);
-	return -ENODEV;
+ out:
+	return ret;
 }
 arch_initcall(iseries_vio_init);
diff --git a/arch/powerpc/platforms/pseries/eeh.c b/arch/powerpc/platforms/pseries/eeh.c
index 22322b35a0ff..fb3d636e088b 100644
--- a/arch/powerpc/platforms/pseries/eeh.c
+++ b/arch/powerpc/platforms/pseries/eeh.c
@@ -186,6 +186,11 @@ static size_t gather_pci_data(struct pci_dn *pdn, char * buf, size_t len)
 	n += scnprintf(buf+n, len-n, "cmd/stat:%x\n", cfg);
 	printk(KERN_WARNING "EEH: PCI cmd/status register: %08x\n", cfg);
 
+	if (!dev) {
+		printk(KERN_WARNING "EEH: no PCI device for this of node\n");
+		return n;
+	}
+
 	/* Gather bridge-specific registers */
 	if (dev->class >> 16 == PCI_BASE_CLASS_BRIDGE) {
 		rtas_read_config(pdn, PCI_SEC_STATUS, 2, &cfg);
@@ -198,7 +203,7 @@ static size_t gather_pci_data(struct pci_dn *pdn, char * buf, size_t len)
 	}
 
 	/* Dump out the PCI-X command and status regs */
-	cap = pci_find_capability(pdn->pcidev, PCI_CAP_ID_PCIX);
+	cap = pci_find_capability(dev, PCI_CAP_ID_PCIX);
 	if (cap) {
 		rtas_read_config(pdn, cap, 4, &cfg);
 		n += scnprintf(buf+n, len-n, "pcix-cmd:%x\n", cfg);
@@ -210,7 +215,7 @@ static size_t gather_pci_data(struct pci_dn *pdn, char * buf, size_t len)
 	}
 
 	/* If PCI-E capable, dump PCI-E cap 10, and the AER */
-	cap = pci_find_capability(pdn->pcidev, PCI_CAP_ID_EXP);
+	cap = pci_find_capability(dev, PCI_CAP_ID_EXP);
 	if (cap) {
 		n += scnprintf(buf+n, len-n, "pci-e cap10:\n");
 		printk(KERN_WARNING
@@ -222,7 +227,7 @@ static size_t gather_pci_data(struct pci_dn *pdn, char * buf, size_t len)
 			printk(KERN_WARNING "EEH: PCI-E %02x: %08x\n", i, cfg);
 		}
 
-		cap = pci_find_ext_capability(pdn->pcidev, PCI_EXT_CAP_ID_ERR);
+		cap = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ERR);
 		if (cap) {
 			n += scnprintf(buf+n, len-n, "pci-e AER:\n");
 			printk(KERN_WARNING
@@ -318,7 +323,7 @@ eeh_wait_for_slot_status(struct pci_dn *pdn, int max_wait_msecs)
 
 		if (rets[2] == 0) return -1; /* permanently unavailable */
 
-		if (max_wait_msecs <= 0) return -1;
+		if (max_wait_msecs <= 0) break;
 
 		mwait = rets[2];
 		if (mwait <= 0) {
diff --git a/arch/powerpc/platforms/pseries/eeh_driver.c b/arch/powerpc/platforms/pseries/eeh_driver.c
index 15e015ef6865..57e025e84ab4 100644
--- a/arch/powerpc/platforms/pseries/eeh_driver.c
+++ b/arch/powerpc/platforms/pseries/eeh_driver.c
@@ -105,17 +105,18 @@ static void eeh_report_error(struct pci_dev *dev, void *userdata)
 		return;
 
 	rc = driver->err_handler->error_detected (dev, pci_channel_io_frozen);
+
+	/* A driver that needs a reset trumps all others */
+	if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
 	if (*res == PCI_ERS_RESULT_NONE) *res = rc;
-	if (*res == PCI_ERS_RESULT_DISCONNECT &&
-	     rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
 }
 
 /**
  * eeh_report_mmio_enabled - tell drivers that MMIO has been enabled
  *
- * Report an EEH error to each device driver, collect up and
- * merge the device driver responses. Cumulative response
- * passed back in "userdata".
+ * Tells each device driver that IO ports, MMIO and config space I/O
+ * are now enabled. Collects up and merges the device driver responses.
+ * Cumulative response passed back in "userdata".
  */
 
 static void eeh_report_mmio_enabled(struct pci_dev *dev, void *userdata)
@@ -123,17 +124,16 @@ static void eeh_report_mmio_enabled(struct pci_dev *dev, void *userdata)
 	enum pci_ers_result rc, *res = userdata;
 	struct pci_driver *driver = dev->driver;
 
-	// dev->error_state = pci_channel_mmio_enabled;
-
 	if (!driver ||
 	    !driver->err_handler ||
 	    !driver->err_handler->mmio_enabled)
 		return;
 
 	rc = driver->err_handler->mmio_enabled (dev);
+
+	/* A driver that needs a reset trumps all others */
+	if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
 	if (*res == PCI_ERS_RESULT_NONE) *res = rc;
-	if (*res == PCI_ERS_RESULT_DISCONNECT &&
-	     rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
 }
 
 /**
diff --git a/arch/powerpc/platforms/pseries/firmware.c b/arch/powerpc/platforms/pseries/firmware.c
index 8b18a1c40092..b765b7c77b65 100644
--- a/arch/powerpc/platforms/pseries/firmware.c
+++ b/arch/powerpc/platforms/pseries/firmware.c
@@ -25,6 +25,7 @@
 
 #include <asm/firmware.h>
 #include <asm/prom.h>
+#include <asm/udbg.h>
 
 #ifdef DEBUG
 #define DBG(fmt...) udbg_printf(fmt)
diff --git a/arch/powerpc/platforms/pseries/msi.c b/arch/powerpc/platforms/pseries/msi.c
index 2793a1b100e6..f15222bbe136 100644
--- a/arch/powerpc/platforms/pseries/msi.c
+++ b/arch/powerpc/platforms/pseries/msi.c
@@ -171,6 +171,7 @@ static int rtas_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type)
 	struct pci_dn *pdn;
 	int hwirq, virq, i, rc;
 	struct msi_desc *entry;
+	struct msi_msg msg;
 
 	pdn = get_pdn(pdev);
 	if (!pdn)
@@ -213,6 +214,11 @@ static int rtas_setup_msi_irqs(struct pci_dev *pdev, int nvec, int type)
 
 		dev_dbg(&pdev->dev, "rtas_msi: allocated virq %d\n", virq);
 		set_irq_msi(virq, entry);
+
+		/* Read config space back so we can restore after reset */
+		read_msi_msg(virq, &msg);
+		entry->msg = msg;
+
 		unmask_msi_irq(virq);
 	}
 
diff --git a/arch/powerpc/sysdev/i8259.c b/arch/powerpc/sysdev/i8259.c
index 7c1b27ac7d3c..216c0f5680d2 100644
--- a/arch/powerpc/sysdev/i8259.c
+++ b/arch/powerpc/sysdev/i8259.c
@@ -137,6 +137,7 @@ static void i8259_unmask_irq(unsigned int irq_nr)
 static struct irq_chip i8259_pic = {
 	.typename	= " i8259    ",
 	.mask		= i8259_mask_irq,
+	.disable	= i8259_mask_irq,
 	.unmask		= i8259_unmask_irq,
 	.mask_ack	= i8259_mask_and_ack_irq,
 };
diff --git a/arch/powerpc/sysdev/mv64x60_pci.c b/arch/powerpc/sysdev/mv64x60_pci.c
index 9b3baa7317d7..6933f9c73b43 100644
--- a/arch/powerpc/sysdev/mv64x60_pci.c
+++ b/arch/powerpc/sysdev/mv64x60_pci.c
@@ -24,8 +24,9 @@
 #define MV64X60_VAL_LEN_MAX		11
 #define MV64X60_PCICFG_CPCI_HOTSWAP	0x68
 
-static ssize_t mv64x60_hs_reg_read(struct kobject *kobj, char *buf, loff_t off,
-				   size_t count)
+static ssize_t mv64x60_hs_reg_read(struct kobject *kobj,
+				   struct bin_attribute *attr, char *buf,
+				   loff_t off, size_t count)
 {
 	struct pci_dev *phb;
 	u32 v;
@@ -44,8 +45,9 @@ static ssize_t mv64x60_hs_reg_read(struct kobject *kobj, char *buf, loff_t off,
 	return sprintf(buf, "0x%08x\n", v);
 }
 
-static ssize_t mv64x60_hs_reg_write(struct kobject *kobj, char *buf, loff_t off,
-				    size_t count)
+static ssize_t mv64x60_hs_reg_write(struct kobject *kobj,
+				    struct bin_attribute *attr, char *buf,
+				    loff_t off, size_t count)
 {
 	struct pci_dev *phb;
 	u32 v;
diff --git a/arch/ppc/kernel/entry.S b/arch/ppc/kernel/entry.S
index fba7ca17a67e..b19bfef2034d 100644
--- a/arch/ppc/kernel/entry.S
+++ b/arch/ppc/kernel/entry.S
@@ -244,6 +244,13 @@ syscall_exit_cont:
 	andis.	r10,r0,DBCR0_IC@h
 	bnel-	load_dbcr0
 #endif
+#ifdef CONFIG_44x
+	lis	r4,icache_44x_need_flush@ha
+	lwz	r5,icache_44x_need_flush@l(r4)
+	cmplwi	cr0,r5,0
+	bne-	2f
+1:
+#endif /* CONFIG_44x */
 	stwcx.	r0,0,r1			/* to clear the reservation */
 	lwz	r4,_LINK(r1)
 	lwz	r5,_CCR(r1)
@@ -258,6 +265,12 @@ syscall_exit_cont:
 	mtspr	SPRN_SRR1,r8
 	SYNC
 	RFI
+#ifdef CONFIG_44x
+2:	li	r7,0
+	iccci	r0,r0
+	stw	r7,icache_44x_need_flush@l(r4)
+	b	1b
+#endif  /* CONFIG_44x */
 
 66:	li	r3,-ENOSYS
 	b	ret_from_syscall
@@ -679,6 +692,16 @@ resume_kernel:
 
 	/* interrupts are hard-disabled at this point */
 restore:
+#ifdef CONFIG_44x
+	lis	r4,icache_44x_need_flush@ha
+	lwz	r5,icache_44x_need_flush@l(r4)
+	cmplwi	cr0,r5,0
+	beq+	1f
+	li	r6,0
+	iccci	r0,r0
+	stw	r6,icache_44x_need_flush@l(r4)
+1:
+#endif  /* CONFIG_44x */
 	lwz	r0,GPR0(r1)
 	lwz	r2,GPR2(r1)
 	REST_4GPRS(3, r1)
diff --git a/arch/ppc/kernel/misc.S b/arch/ppc/kernel/misc.S
index a22e1f4d94c8..e0c850d85c53 100644
--- a/arch/ppc/kernel/misc.S
+++ b/arch/ppc/kernel/misc.S
@@ -224,7 +224,16 @@ _GLOBAL(_tlbia)
  */
 _GLOBAL(_tlbie)
 #if defined(CONFIG_40x)
+	/* We run the search with interrupts disabled because we have to change
+	 * the PID and I don't want to preempt when that happens.
+	 */
+	mfmsr	r5
+	mfspr	r6,SPRN_PID
+	wrteei	0
+	mtspr	SPRN_PID,r4
 	tlbsx.	r3, 0, r3
+	mtspr	SPRN_PID,r6
+	wrtee	r5
 	bne	10f
 	sync
 	/* There are only 64 TLB entries, so r3 < 64, which means bit 25 is clear.
@@ -234,22 +243,21 @@ _GLOBAL(_tlbie)
 	isync
 10:
 #elif defined(CONFIG_44x)
-	mfspr	r4,SPRN_MMUCR
-	mfspr	r5,SPRN_PID			/* Get PID */
-	rlwimi	r4,r5,0,24,31			/* Set TID */
+	mfspr	r5,SPRN_MMUCR
+	rlwimi	r5,r4,0,24,31			/* Set TID */
 
 	/* We have to run the search with interrupts disabled, even critical
 	 * and debug interrupts (in fact the only critical exceptions we have
 	 * are debug and machine check).  Otherwise  an interrupt which causes
 	 * a TLB miss can clobber the MMUCR between the mtspr and the tlbsx. */
-	mfmsr	r5
+	mfmsr	r4
 	lis	r6,(MSR_EE|MSR_CE|MSR_ME|MSR_DE)@ha
 	addi	r6,r6,(MSR_EE|MSR_CE|MSR_ME|MSR_DE)@l
-	andc	r6,r5,r6
+	andc	r6,r4,r6
 	mtmsr	r6
-	mtspr	SPRN_MMUCR,r4
+	mtspr	SPRN_MMUCR,r5
 	tlbsx.	r3, 0, r3
-	mtmsr	r5
+	mtmsr	r4
 	bne	10f
 	sync
 	/* There are only 64 TLB entries, so r3 < 64,
@@ -491,12 +499,21 @@ END_FTR_SECTION_IFSET(CPU_FTR_COHERENT_ICACHE)
 	addi	r3,r3,L1_CACHE_BYTES
 	bdnz	0b
 	sync
+#ifndef CONFIG_44x
+	/* We don't flush the icache on 44x. Those have a virtual icache
+	 * and we don't have access to the virtual address here (it's
+	 * not the page vaddr but where it's mapped in user space). The
+	 * flushing of the icache on these is handled elsewhere, when
+	 * a change in the address space occurs, before returning to
+	 * user space
+	 */
 	mtctr	r4
 1:	icbi	0,r6
 	addi	r6,r6,L1_CACHE_BYTES
 	bdnz	1b
 	sync
 	isync
+#endif /* CONFIG_44x */
 	blr
 
 /*
diff --git a/arch/ppc/mm/44x_mmu.c b/arch/ppc/mm/44x_mmu.c
index 0a0a0487b334..6536a25cfcb8 100644
--- a/arch/ppc/mm/44x_mmu.c
+++ b/arch/ppc/mm/44x_mmu.c
@@ -61,6 +61,7 @@ extern char etext[], _stext[];
  */
 unsigned int tlb_44x_index = 0;
 unsigned int tlb_44x_hwater = 62;
+int icache_44x_need_flush;
 
 /*
  * "Pins" a 256MB TLB entry in AS0 for kernel lowmem
diff --git a/arch/ppc/mm/4xx_mmu.c b/arch/ppc/mm/4xx_mmu.c
index 838e09db71d9..ea785dbaac7c 100644
--- a/arch/ppc/mm/4xx_mmu.c
+++ b/arch/ppc/mm/4xx_mmu.c
@@ -99,13 +99,12 @@ unsigned long __init mmu_mapin_ram(void)
 
 	v = KERNELBASE;
 	p = PPC_MEMSTART;
-	s = 0;
+	s = total_lowmem;
 
-	if (__map_without_ltlbs) {
-		return s;
-	}
+	if (__map_without_ltlbs)
+		return 0;
 
-	while (s <= (total_lowmem - LARGE_PAGE_SIZE_16M)) {
+	while (s >= LARGE_PAGE_SIZE_16M) {
 		pmd_t *pmdp;
 		unsigned long val = p | _PMD_SIZE_16M | _PAGE_HWEXEC | _PAGE_HWWRITE;
 
@@ -117,10 +116,10 @@ unsigned long __init mmu_mapin_ram(void)
 
 		v += LARGE_PAGE_SIZE_16M;
 		p += LARGE_PAGE_SIZE_16M;
-		s += LARGE_PAGE_SIZE_16M;
+		s -= LARGE_PAGE_SIZE_16M;
 	}
 
-	while (s <= (total_lowmem - LARGE_PAGE_SIZE_4M)) {
+	while (s >= LARGE_PAGE_SIZE_4M) {
 		pmd_t *pmdp;
 		unsigned long val = p | _PMD_SIZE_4M | _PAGE_HWEXEC | _PAGE_HWWRITE;
 
@@ -129,8 +128,8 @@ unsigned long __init mmu_mapin_ram(void)
 
 		v += LARGE_PAGE_SIZE_4M;
 		p += LARGE_PAGE_SIZE_4M;
-		s += LARGE_PAGE_SIZE_4M;
+		s -= LARGE_PAGE_SIZE_4M;
 	}
 
-	return s;
+	return total_lowmem - s;
 }
diff --git a/arch/ppc/mm/fault.c b/arch/ppc/mm/fault.c
index 254c23b755e6..36c0e7529edb 100644
--- a/arch/ppc/mm/fault.c
+++ b/arch/ppc/mm/fault.c
@@ -227,7 +227,7 @@ good_area:
 					set_bit(PG_arch_1, &page->flags);
 				}
 				pte_update(ptep, 0, _PAGE_HWEXEC);
-				_tlbie(address);
+				_tlbie(address, mm->context.id);
 				pte_unmap_unlock(ptep, ptl);
 				up_read(&mm->mmap_sem);
 				return 0;
diff --git a/arch/ppc/mm/mmu_decl.h b/arch/ppc/mm/mmu_decl.h
index 540f3292b229..f1d4f2109a99 100644
--- a/arch/ppc/mm/mmu_decl.h
+++ b/arch/ppc/mm/mmu_decl.h
@@ -54,12 +54,12 @@ extern unsigned int num_tlbcam_entries;
 #define mmu_mapin_ram()		(0UL)
 
 #elif defined(CONFIG_4xx)
-#define flush_HPTE(X, va, pg)	_tlbie(va)
+#define flush_HPTE(pid, va, pg)	_tlbie(va, pid)
 extern void MMU_init_hw(void);
 extern unsigned long mmu_mapin_ram(void);
 
 #elif defined(CONFIG_FSL_BOOKE)
-#define flush_HPTE(X, va, pg)	_tlbie(va)
+#define flush_HPTE(pid, va, pg)	_tlbie(va, pid)
 extern void MMU_init_hw(void);
 extern unsigned long mmu_mapin_ram(void);
 extern void adjust_total_lowmem(void);
diff --git a/arch/ppc/platforms/4xx/ebony.c b/arch/ppc/platforms/4xx/ebony.c
index 05d7184d7e14..453643a0eeea 100644
--- a/arch/ppc/platforms/4xx/ebony.c
+++ b/arch/ppc/platforms/4xx/ebony.c
@@ -236,7 +236,7 @@ ebony_early_serial_map(void)
 	gen550_init(0, &port);
 
 	/* Purge TLB entry added in head_44x.S for early serial access */
-	_tlbie(UART0_IO_BASE);
+	_tlbie(UART0_IO_BASE, 0);
 #endif
 
 	port.membase = ioremap64(PPC440GP_UART1_ADDR, 8);
diff --git a/arch/ppc/platforms/4xx/luan.c b/arch/ppc/platforms/4xx/luan.c
index 4b169610f154..b79ebb8a3e6c 100644
--- a/arch/ppc/platforms/4xx/luan.c
+++ b/arch/ppc/platforms/4xx/luan.c
@@ -230,10 +230,15 @@ luan_setup_hoses(void)
 
 	/* Allocate hoses for PCIX1 and PCIX2 */
 	hose1 = pcibios_alloc_controller();
-	hose2 = pcibios_alloc_controller();
-	if (!hose1 || !hose2)
+	if (!hose1)
 		return;
 
+	hose2 = pcibios_alloc_controller();
+	if (!hose2) {
+		pcibios_free_controller(hose1);
+		return;
+	}
+
 	/* Setup PCIX1 */
 	hose1->first_busno = 0;
 	hose1->last_busno = 0xff;
diff --git a/arch/ppc/platforms/4xx/ocotea.c b/arch/ppc/platforms/4xx/ocotea.c
index fd0f971881d6..28a712cd4800 100644
--- a/arch/ppc/platforms/4xx/ocotea.c
+++ b/arch/ppc/platforms/4xx/ocotea.c
@@ -259,7 +259,7 @@ ocotea_early_serial_map(void)
 	gen550_init(0, &port);
 
 	/* Purge TLB entry added in head_44x.S for early serial access */
-	_tlbie(UART0_IO_BASE);
+	_tlbie(UART0_IO_BASE, 0);
 #endif
 
 	port.membase = ioremap64(PPC440GX_UART1_ADDR, 8);
diff --git a/arch/ppc/platforms/4xx/taishan.c b/arch/ppc/platforms/4xx/taishan.c
index 888c492b4a45..f6a0c6650f33 100644
--- a/arch/ppc/platforms/4xx/taishan.c
+++ b/arch/ppc/platforms/4xx/taishan.c
@@ -316,7 +316,7 @@ taishan_early_serial_map(void)
 	gen550_init(0, &port);
 
 	/* Purge TLB entry added in head_44x.S for early serial access */
-	_tlbie(UART0_IO_BASE);
+	_tlbie(UART0_IO_BASE, 0);
 #endif
 
 	port.membase = ioremap64(PPC440GX_UART1_ADDR, 8);
diff --git a/arch/ppc/syslib/i8259.c b/arch/ppc/syslib/i8259.c
index 1e5a00a4b5f5..559f27c6aefe 100644
--- a/arch/ppc/syslib/i8259.c
+++ b/arch/ppc/syslib/i8259.c
@@ -127,6 +127,7 @@ static void i8259_unmask_irq(unsigned int irq_nr)
 static struct irq_chip i8259_pic = {
 	.typename	= " i8259    ",
 	.mask		= i8259_mask_irq,
+	.disable	= i8259_mask_irq,
 	.unmask		= i8259_unmask_irq,
 	.mask_ack	= i8259_mask_and_ack_irq,
 };
diff --git a/arch/ppc/syslib/m8260_setup.c b/arch/ppc/syslib/m8260_setup.c
index 15f0d7323535..46588fa94381 100644
--- a/arch/ppc/syslib/m8260_setup.c
+++ b/arch/ppc/syslib/m8260_setup.c
@@ -25,6 +25,7 @@
 #include <asm/machdep.h>
 #include <asm/bootinfo.h>
 #include <asm/time.h>
+#include <asm/ppc_sys.h>
 
 #include "cpm2_pic.h"
 
@@ -61,7 +62,7 @@ m8260_setup_arch(void)
 #endif
 
 	identify_ppc_sys_by_name_and_id(BOARD_CHIP_NAME,
-				in_be32(CPM_MAP_ADDR + CPM_IMMR_OFFSET));
+			in_be32((void *)CPM_MAP_ADDR + CPM_IMMR_OFFSET));
 
 	m82xx_board_setup();
 }
@@ -147,12 +148,12 @@ m8260_show_cpuinfo(struct seq_file *m)
 	seq_printf(m, "vendor\t\t: %s\n"
 		   "machine\t\t: %s\n"
 		   "\n"
-		   "mem size\t\t: 0x%08x\n"
-		   "console baud\t\t: %d\n"
+		   "mem size\t\t: 0x%08lx\n"
+		   "console baud\t\t: %ld\n"
 		   "\n"
-		   "core clock\t: %u MHz\n"
-		   "CPM  clock\t: %u MHz\n"
-		   "bus  clock\t: %u MHz\n",
+		   "core clock\t: %lu MHz\n"
+		   "CPM  clock\t: %lu MHz\n"
+		   "bus  clock\t: %lu MHz\n",
 		   CPUINFO_VENDOR, CPUINFO_MACHINE, bp->bi_memsize,
 		   bp->bi_baudrate, bp->bi_intfreq / 1000000,
 		   bp->bi_cpmfreq / 1000000, bp->bi_busfreq / 1000000);
diff --git a/drivers/macintosh/windfarm_core.c b/drivers/macintosh/windfarm_core.c
index 516d943227e2..075b4d99e354 100644
--- a/drivers/macintosh/windfarm_core.c
+++ b/drivers/macintosh/windfarm_core.c
@@ -94,7 +94,9 @@ static int wf_thread_func(void *data)
 	DBG("wf: thread started\n");
 
 	set_freezable();
-	while(!kthread_should_stop()) {
+	while (!kthread_should_stop()) {
+		try_to_freeze();
+
 		if (time_after_eq(jiffies, next)) {
 			wf_notify(WF_EVENT_TICK, NULL);
 			if (wf_overtemp) {
@@ -116,12 +118,6 @@ static int wf_thread_func(void *data)
 		delay = next - jiffies;
 		if (delay <= HZ)
 			schedule_timeout_interruptible(delay);
-
-		/* there should be no non-suspend signal, but oh well */
-		if (signal_pending(current) && !try_to_freeze()) {
-			printk(KERN_WARNING "windfarm: thread got sigl !\n");
-			break;
-		}
 	}
 
 	DBG("wf: thread stopped\n");
diff --git a/drivers/serial/uartlite.c b/drivers/serial/uartlite.c
index dfef83f14960..a85f2d31a686 100644
--- a/drivers/serial/uartlite.c
+++ b/drivers/serial/uartlite.c
@@ -329,12 +329,14 @@ static struct uart_ops ulite_ops = {
 static void ulite_console_wait_tx(struct uart_port *port)
 {
 	int i;
+	u8 val;
 
-	/* wait up to 10ms for the character(s) to be sent */
-	for (i = 0; i < 10000; i++) {
-		if (readb(port->membase + ULITE_STATUS) & ULITE_STATUS_TXEMPTY)
+	/* Spin waiting for TX fifo to have space available */
+	for (i = 0; i < 100000; i++) {
+		val = readb(port->membase + ULITE_STATUS);
+		if ((val & ULITE_STATUS_TXFULL) == 0)
 			break;
-		udelay(1);
+		cpu_relax();
 	}
 }
 
diff --git a/include/asm-powerpc/pgtable-ppc32.h b/include/asm-powerpc/pgtable-ppc32.h
index 86a54a4a8a2a..fea2d8ff1e73 100644
--- a/include/asm-powerpc/pgtable-ppc32.h
+++ b/include/asm-powerpc/pgtable-ppc32.h
@@ -11,6 +11,11 @@
 extern unsigned long va_to_phys(unsigned long address);
 extern pte_t *va_to_pte(unsigned long address);
 extern unsigned long ioremap_bot, ioremap_base;
+
+#ifdef CONFIG_44x
+extern int icache_44x_need_flush;
+#endif
+
 #endif /* __ASSEMBLY__ */
 
 /*
@@ -562,6 +567,10 @@ static inline unsigned long pte_update(pte_t *p, unsigned long clr,
 	: "=&r" (old), "=&r" (tmp), "=m" (*p)
 	: "r" (p), "r" (clr), "r" (set), "m" (*p)
 	: "cc" );
+#ifdef CONFIG_44x
+	if ((old & _PAGE_USER) && (old & _PAGE_HWEXEC))
+		icache_44x_need_flush = 1;
+#endif
 	return old;
 }
 #else
@@ -582,6 +591,10 @@ static inline unsigned long long pte_update(pte_t *p, unsigned long clr,
 	: "=&r" (old), "=&r" (tmp), "=m" (*p)
 	: "r" (p), "r" ((unsigned long)(p) + 4), "r" (clr), "r" (set), "m" (*p)
 	: "cc" );
+#ifdef CONFIG_44x
+	if ((old & _PAGE_USER) && (old & _PAGE_HWEXEC))
+		icache_44x_need_flush = 1;
+#endif
 	return old;
 }
 #endif
diff --git a/include/asm-powerpc/systbl.h b/include/asm-powerpc/systbl.h
index cc6d87228258..11d5383b2f09 100644
--- a/include/asm-powerpc/systbl.h
+++ b/include/asm-powerpc/systbl.h
@@ -308,8 +308,8 @@ COMPAT_SYS_SPU(move_pages)
 SYSCALL_SPU(getcpu)
 COMPAT_SYS(epoll_pwait)
 COMPAT_SYS_SPU(utimensat)
-COMPAT_SYS(fallocate)
 COMPAT_SYS_SPU(signalfd)
 COMPAT_SYS_SPU(timerfd)
 SYSCALL_SPU(eventfd)
 COMPAT_SYS_SPU(sync_file_range2)
+COMPAT_SYS(fallocate)
diff --git a/include/asm-powerpc/time.h b/include/asm-powerpc/time.h
index f05895522f7f..780f82642756 100644
--- a/include/asm-powerpc/time.h
+++ b/include/asm-powerpc/time.h
@@ -176,25 +176,31 @@ static inline unsigned int get_dec(void)
 #endif
 }
 
+/*
+ * Note: Book E and 4xx processors differ from other PowerPC processors
+ * in when the decrementer generates its interrupt: on the 1 to 0
+ * transition for Book E/4xx, but on the 0 to -1 transition for others.
+ */
 static inline void set_dec(int val)
 {
 #if defined(CONFIG_40x)
 	mtspr(SPRN_PIT, val);
 #elif defined(CONFIG_8xx_CPU6)
-	set_dec_cpu6(val);
+	set_dec_cpu6(val - 1);
 #else
+#ifndef CONFIG_BOOKE
+	--val;
+#endif
 #ifdef CONFIG_PPC_ISERIES
-	int cur_dec;
-
 	if (firmware_has_feature(FW_FEATURE_ISERIES) &&
 			get_lppaca()->shared_proc) {
 		get_lppaca()->virtual_decr = val;
-		cur_dec = get_dec();
-		if (cur_dec > val)
+		if (get_dec() > val)
 			HvCall_setVirtualDecr();
-	} else
+		return;
+	}
 #endif
-		mtspr(SPRN_DEC, val);
+	mtspr(SPRN_DEC, val);
 #endif /* not 40x or 8xx_CPU6 */
 }
 
diff --git a/include/asm-powerpc/tlbflush.h b/include/asm-powerpc/tlbflush.h
index b6b036ccee34..e7b4c0d298ae 100644
--- a/include/asm-powerpc/tlbflush.h
+++ b/include/asm-powerpc/tlbflush.h
@@ -1,5 +1,6 @@
 #ifndef _ASM_POWERPC_TLBFLUSH_H
 #define _ASM_POWERPC_TLBFLUSH_H
+
 /*
  * TLB flushing:
  *
@@ -16,9 +17,6 @@
  */
 #ifdef __KERNEL__
 
-struct mm_struct;
-struct vm_area_struct;
-
 #if defined(CONFIG_4xx) || defined(CONFIG_8xx) || defined(CONFIG_FSL_BOOKE)
 /*
  * TLB flushing for software loaded TLB chips
@@ -28,7 +26,9 @@ struct vm_area_struct;
  * specific tlbie's
  */
 
-extern void _tlbie(unsigned long address);
+#include <linux/mm.h>
+
+extern void _tlbie(unsigned long address, unsigned int pid);
 
 #if defined(CONFIG_40x) || defined(CONFIG_8xx)
 #define _tlbia()	asm volatile ("tlbia; sync" : : : "memory")
@@ -44,13 +44,13 @@ static inline void flush_tlb_mm(struct mm_struct *mm)
 static inline void flush_tlb_page(struct vm_area_struct *vma,
 				  unsigned long vmaddr)
 {
-	_tlbie(vmaddr);
+	_tlbie(vmaddr, vma->vm_mm->context.id);
 }
 
 static inline void flush_tlb_page_nohash(struct vm_area_struct *vma,
 					 unsigned long vmaddr)
 {
-	_tlbie(vmaddr);
+	_tlbie(vmaddr, vma->vm_mm->context.id);
 }
 
 static inline void flush_tlb_range(struct vm_area_struct *vma,