USB: EHCI: Allow users to override 80% max periodic bandwidth

There are cases, when 80% max isochronous bandwidth is too limiting.

For example I have two USB video capture cards which stream uncompressed
video, and to stream full NTSC + PAL videos we'd need

    NTSC 640x480 YUV422 @30fps      ~17.6 MB/s
    PAL  720x576 YUV422 @25fps      ~19.7 MB/s

isoc bandwidth.

Now, due to limited alt settings in capture devices NTSC one ends up
streaming with max_pkt_size=2688  and  PAL with max_pkt_size=2892, both
with interval=1. In terms of microframe time allocation this gives

    NTSC    ~53us
    PAL     ~57us

and together

    ~110us  >  100us == 80% of 125us uframe time.

So those two devices can't work together simultaneously because the'd
over allocate isochronous bandwidth.

80% seemed a bit arbitrary to me, and I've tried to raise it to 90% and
both devices started to work together, so I though sometimes it would be
a good idea for users to override hardcoded default of max 80% isoc
bandwidth.

After all, isn't it a user who should decide how to load the bus? If I
can live with 10% or even 5% bulk bandwidth that should be ok. I'm a USB
newcomer, but that 80% set in stone by USB 2.0 specification seems to be
chosen pretty arbitrary to me, just to serve as a reasonable default.

NOTE 1
~~~~~~

for two streams with max_pkt_size=3072 (worst case) both time
allocation would be 60us+60us=120us which is 96% periodic bandwidth
leaving 4% for bulk and control.  Alan Stern suggested that bulk then
would be problematic (less than 300*8 bittimes left per microframe), but
I think that is still enough for control traffic.

NOTE 2
~~~~~~

Sarah Sharp expressed concern that maxing out periodic bandwidth
could lead to vendor-specific hardware bugs on host controllers, because

> It's entirely possible that you'll run into
> vendor-specific bugs if you try to pack the schedule with isochronous
> transfers.  I don't think any hardware designer would seriously test or
> validate their hardware with a schedule that is basically a violation of
> the USB bus spec (more than 80% for periodic transfers).

So far I've only tested this patch on my HP Mini 5103 with N10 chipset

    kirr@mini:~$ lspci
    00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
    00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
    00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
    00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
    00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
    00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02)
    00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02)
    00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
    00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
    00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
    00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
    00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
    00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
    00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02)
    01:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
    02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8059 PCI-E Gigabit Ethernet Controller (rev 11)

and the system works stable with 110us/uframe (~88%) isoc bandwith allocated for
above-mentioned isochronous transfers.

NOTE 3
~~~~~~

This feature is off by default. I mean max periodic bandwidth is set to
100us/uframe by default exactly as it was before the patch. So only those of us
who need the extreme settings are taking the risk - normal users who do not
alter uframe_periodic_max sysfs attribute should not see any change at all.

NOTE 4
~~~~~~

I've tried to update documentation in Documentation/ABI/ thoroughly, but
only "TBD" was put into Documentation/usb/ehci.txt -- the text there seems
to be outdated and much needing refreshing, before it could be amended.

Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit is contained in:
Kirill Smelkov 2011-07-03 20:36:57 +04:00 committed by Greg Kroah-Hartman
parent 4c67045bfc
commit cc62a7eb63
6 changed files with 140 additions and 14 deletions

View File

@ -10,3 +10,26 @@ KernelVersion: 2.6.35
Contact: masa-korg@dsn.okisemi.com
Description: Write/read Option ROM data.
What: /sys/module/ehci_hcd/drivers/.../uframe_periodic_max
Date: July 2011
KernelVersion: 3.1
Contact: Kirill Smelkov <kirr@mns.spb.ru>
Description: Maximum time allowed for periodic transfers per microframe (μs)
[ USB 2.0 sets maximum allowed time for periodic transfers per
microframe to be 80%, that is 100 microseconds out of 125
microseconds (full microframe).
However there are cases, when 80% max isochronous bandwidth is
too limiting. For example two video streams could require 110
microseconds of isochronous bandwidth per microframe to work
together. ]
Through this setting it is possible to raise the limit so that
the host controller would allow allocating more than 100
microseconds of periodic bandwidth per microframe.
Beware, non-standard modes are usually not thoroughly tested by
hardware designers, and the hardware can malfunction when this
setting differ from default 100.

View File

@ -210,3 +210,5 @@ TBD: Interrupt and ISO transfer performance issues. Those periodic
transfers are fully scheduled, so the main issue is likely to be how
to trigger "high bandwidth" modes.
TBD: More than standard 80% periodic bandwidth allocation is possible
through sysfs uframe_periodic_max parameter. Describe that.

View File

@ -571,6 +571,12 @@ static int ehci_init(struct usb_hcd *hcd)
hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params);
/*
* by default set standard 80% (== 100 usec/uframe) max periodic
* bandwidth as required by USB 2.0
*/
ehci->uframe_periodic_max = 100;
/*
* hw default: 1K periodic list heads, one per frame.
* periodic_size can shrink by USBCMD update if hcc_params allows.

View File

@ -172,7 +172,7 @@ periodic_usecs (struct ehci_hcd *ehci, unsigned frame, unsigned uframe)
}
}
#ifdef DEBUG
if (usecs > 100)
if (usecs > ehci->uframe_periodic_max)
ehci_err (ehci, "uframe %d sched overrun: %d usecs\n",
frame * 8 + uframe, usecs);
#endif
@ -709,11 +709,8 @@ static int check_period (
if (uframe >= 8)
return 0;
/*
* 80% periodic == 100 usec/uframe available
* convert "usecs we need" to "max already claimed"
*/
usecs = 100 - usecs;
/* convert "usecs we need" to "max already claimed" */
usecs = ehci->uframe_periodic_max - usecs;
/* we "know" 2 and 4 uframe intervals were rejected; so
* for period 0, check _every_ microframe in the schedule.
@ -1286,9 +1283,9 @@ itd_slot_ok (
{
uframe %= period;
do {
/* can't commit more than 80% periodic == 100 usec */
/* can't commit more than uframe_periodic_max usec */
if (periodic_usecs (ehci, uframe >> 3, uframe & 0x7)
> (100 - usecs))
> (ehci->uframe_periodic_max - usecs))
return 0;
/* we know urb->interval is 2^N uframes */
@ -1345,7 +1342,7 @@ sitd_slot_ok (
#endif
/* check starts (OUT uses more than one) */
max_used = 100 - stream->usecs;
max_used = ehci->uframe_periodic_max - stream->usecs;
for (tmp = stream->raw_mask & 0xff; tmp; tmp >>= 1, uf++) {
if (periodic_usecs (ehci, frame, uf) > max_used)
return 0;
@ -1354,7 +1351,7 @@ sitd_slot_ok (
/* for IN, check CSPLIT */
if (stream->c_usecs) {
uf = uframe & 7;
max_used = 100 - stream->c_usecs;
max_used = ehci->uframe_periodic_max - stream->c_usecs;
do {
tmp = 1 << uf;
tmp <<= 8;

View File

@ -74,21 +74,117 @@ static ssize_t store_companion(struct device *dev,
}
static DEVICE_ATTR(companion, 0644, show_companion, store_companion);
/*
* Display / Set uframe_periodic_max
*/
static ssize_t show_uframe_periodic_max(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct ehci_hcd *ehci;
int n;
ehci = hcd_to_ehci(bus_to_hcd(dev_get_drvdata(dev)));
n = scnprintf(buf, PAGE_SIZE, "%d\n", ehci->uframe_periodic_max);
return n;
}
static ssize_t store_uframe_periodic_max(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct ehci_hcd *ehci;
unsigned uframe_periodic_max;
unsigned frame, uframe;
unsigned short allocated_max;
unsigned long flags;
ssize_t ret;
ehci = hcd_to_ehci(bus_to_hcd(dev_get_drvdata(dev)));
if (kstrtouint(buf, 0, &uframe_periodic_max) < 0)
return -EINVAL;
if (uframe_periodic_max < 100 || uframe_periodic_max >= 125) {
ehci_info(ehci, "rejecting invalid request for "
"uframe_periodic_max=%u\n", uframe_periodic_max);
return -EINVAL;
}
ret = -EINVAL;
/*
* lock, so that our checking does not race with possible periodic
* bandwidth allocation through submitting new urbs.
*/
spin_lock_irqsave (&ehci->lock, flags);
/*
* for request to decrease max periodic bandwidth, we have to check
* every microframe in the schedule to see whether the decrease is
* possible.
*/
if (uframe_periodic_max < ehci->uframe_periodic_max) {
allocated_max = 0;
for (frame = 0; frame < ehci->periodic_size; ++frame)
for (uframe = 0; uframe < 7; ++uframe)
allocated_max = max(allocated_max,
periodic_usecs (ehci, frame, uframe));
if (allocated_max > uframe_periodic_max) {
ehci_info(ehci,
"cannot decrease uframe_periodic_max becase "
"periodic bandwidth is already allocated "
"(%u > %u)\n",
allocated_max, uframe_periodic_max);
goto out_unlock;
}
}
/* increasing is always ok */
ehci_info(ehci, "setting max periodic bandwidth to %u%% "
"(== %u usec/uframe)\n",
100*uframe_periodic_max/125, uframe_periodic_max);
if (uframe_periodic_max != 100)
ehci_warn(ehci, "max periodic bandwidth set is non-standard\n");
ehci->uframe_periodic_max = uframe_periodic_max;
ret = count;
out_unlock:
spin_unlock_irqrestore (&ehci->lock, flags);
return ret;
}
static DEVICE_ATTR(uframe_periodic_max, 0644, show_uframe_periodic_max, store_uframe_periodic_max);
static inline int create_sysfs_files(struct ehci_hcd *ehci)
{
struct device *controller = ehci_to_hcd(ehci)->self.controller;
int i = 0;
/* with integrated TT there is no companion! */
if (!ehci_is_TDI(ehci))
i = device_create_file(ehci_to_hcd(ehci)->self.controller,
&dev_attr_companion);
i = device_create_file(controller, &dev_attr_companion);
if (i)
goto out;
i = device_create_file(controller, &dev_attr_uframe_periodic_max);
out:
return i;
}
static inline void remove_sysfs_files(struct ehci_hcd *ehci)
{
struct device *controller = ehci_to_hcd(ehci)->self.controller;
/* with integrated TT there is no companion! */
if (!ehci_is_TDI(ehci))
device_remove_file(ehci_to_hcd(ehci)->self.controller,
&dev_attr_companion);
device_remove_file(controller, &dev_attr_companion);
device_remove_file(controller, &dev_attr_uframe_periodic_max);
}

View File

@ -87,6 +87,8 @@ struct ehci_hcd { /* one per controller */
union ehci_shadow *pshadow; /* mirror hw periodic table */
int next_uframe; /* scan periodic, start here */
unsigned periodic_sched; /* periodic activity count */
unsigned uframe_periodic_max; /* max periodic time per uframe */
/* list of itds & sitds completed while clock_frame was still active */
struct list_head cached_itd_list;