diff --git a/Documentation/devicetree/bindings/regulator/88pm800.txt b/Documentation/devicetree/bindings/regulator/88pm800.txt new file mode 100644 index 000000000000..e8a54c2a5821 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/88pm800.txt @@ -0,0 +1,38 @@ +Marvell 88PM800 regulator + +Required properties: +- compatible: "marvell,88pm800" +- reg: I2C slave address +- regulators: A node that houses a sub-node for each regulator within the + device. Each sub-node is identified using the node's name (or the deprecated + regulator-compatible property if present), with valid values listed below. + The content of each sub-node is defined by the standard binding for + regulators; see regulator.txt. + +The valid names for regulators are: + + buck1, buck2, buck3, buck4, buck5, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, + ldo8, ldo9, ldo10, ldo11, ldo12, ldo13, ldo14, ldo15, ldo16, ldo17, ldo18, ldo19 + +Example: + + pmic: 88pm800@31 { + compatible = "marvell,88pm800"; + reg = <0x31>; + + regulators { + buck1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3950000>; + regulator-boot-on; + regulator-always-on; + }; + ldo1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <15000000>; + regulator-boot-on; + regulator-always-on; + }; +... + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8660.txt b/Documentation/devicetree/bindings/regulator/max8660.txt new file mode 100644 index 000000000000..8ba994d8a142 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8660.txt @@ -0,0 +1,47 @@ +Maxim MAX8660 voltage regulator + +Required properties: +- compatible: must be one of "maxim,max8660", "maxim,max8661" +- reg: I2C slave address, usually 0x34 +- any required generic properties defined in regulator.txt + +Example: + + i2c_master { + max8660@34 { + compatible = "maxim,max8660"; + reg = <0x34>; + + regulators { + regulator@0 { + regulator-compatible= "V3(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@1 { + regulator-compatible= "V4(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator@2 { + regulator-compatible= "V5(LDO)"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + }; + + regulator@3 { + regulator-compatible= "V6(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + regulator@4 { + regulator-compatible= "V7(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt index 30b0581bb1ce..a22e4c70db5c 100644 --- a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -25,8 +25,8 @@ Optional nodes: Additional custom properties are listed below. For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP, - smps45, smps457, smps7 depending on variant, smps6, smps[8-10], - ldo[1-9], ldoln, ldousb. + smps45, smps457, smps7 depending on variant, smps6, smps[8-9], + smps10_out2, smps10_out1, do[1-9], ldoln, ldousb. Optional sub-node properties: ti,warm-reset - maintain voltage during warm reset(boolean) diff --git a/Documentation/devicetree/bindings/regulator/pfuze100.txt b/Documentation/devicetree/bindings/regulator/pfuze100.txt new file mode 100644 index 000000000000..fc989b2e8057 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/pfuze100.txt @@ -0,0 +1,115 @@ +PFUZE100 family of regulators + +Required properties: +- compatible: "fsl,pfuze100" +- reg: I2C slave address + +Required child node: +- regulators: This is the list of child nodes that specify the regulator + initialization data for defined regulators. Please refer to below doc + Documentation/devicetree/bindings/regulator/regulator.txt. + + The valid names for regulators are: + sw1ab,sw1c,sw2,sw3a,sw3b,sw4,swbst,vsnvs,vrefddr,vgen1~vgen6 + +Each regulator is defined using the standard binding for regulators. + +Example: + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 48a3b8e5d6bd..2bd8f0978765 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -12,6 +12,8 @@ Optional properties: - regulator-allow-bypass: allow the regulator to go into bypass mode - -supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) + For hardwares which support disabling ramp rate, it should be explicitly + intialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/drivers/cpufreq/cpufreq-cpu0.c b/drivers/cpufreq/cpufreq-cpu0.c index ad1fde277661..e9dedb27deca 100644 --- a/drivers/cpufreq/cpufreq-cpu0.c +++ b/drivers/cpufreq/cpufreq-cpu0.c @@ -197,7 +197,7 @@ static int cpu0_cpufreq_probe(struct platform_device *pdev) cpu_dev = &pdev->dev; cpu_dev->of_node = np; - cpu_reg = devm_regulator_get(cpu_dev, "cpu0"); + cpu_reg = devm_regulator_get_optional(cpu_dev, "cpu0"); if (IS_ERR(cpu_reg)) { /* * If cpu0 regulator supply node is present, but regulator is diff --git a/drivers/hwmon/sht15.c b/drivers/hwmon/sht15.c index 2507f902fb7a..ab5dc3af4cfb 100644 --- a/drivers/hwmon/sht15.c +++ b/drivers/hwmon/sht15.c @@ -957,7 +957,7 @@ static int sht15_probe(struct platform_device *pdev) * If a regulator is available, * query what the supply voltage actually is! */ - data->reg = devm_regulator_get(data->dev, "vcc"); + data->reg = devm_regulator_get_optional(data->dev, "vcc"); if (!IS_ERR(data->reg)) { int voltage; diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index 49a5bca418bd..5d088551196b 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -1313,7 +1313,7 @@ int mmc_regulator_get_supply(struct mmc_host *mmc) supply = devm_regulator_get(dev, "vmmc"); mmc->supply.vmmc = supply; - mmc->supply.vqmmc = devm_regulator_get(dev, "vqmmc"); + mmc->supply.vqmmc = devm_regulator_get_optional(dev, "vqmmc"); if (IS_ERR(supply)) return PTR_ERR(supply); diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c index ee5f1676f14e..542407363dd2 100644 --- a/drivers/mmc/host/dw_mmc.c +++ b/drivers/mmc/host/dw_mmc.c @@ -2231,7 +2231,7 @@ int dw_mci_probe(struct dw_mci *host) } } - host->vmmc = devm_regulator_get(host->dev, "vmmc"); + host->vmmc = devm_regulator_get_optional(host->dev, "vmmc"); if (IS_ERR(host->vmmc)) { ret = PTR_ERR(host->vmmc); if (ret == -EPROBE_DEFER) diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c index 2c5a91bb8ec3..1956a3df7cf3 100644 --- a/drivers/mmc/host/pxamci.c +++ b/drivers/mmc/host/pxamci.c @@ -83,7 +83,7 @@ struct pxamci_host { static inline void pxamci_init_ocr(struct pxamci_host *host) { #ifdef CONFIG_REGULATOR - host->vcc = regulator_get(mmc_dev(host->mmc), "vmmc"); + host->vcc = regulator_get_optional(mmc_dev(host->mmc), "vmmc"); if (IS_ERR(host->vcc)) host->vcc = NULL; diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index a78bd4f3aecc..dd2c083c434d 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -2966,7 +2966,7 @@ int sdhci_add_host(struct sdhci_host *host) mmc->caps |= MMC_CAP_NEEDS_POLL; /* If vqmmc regulator and no 1.8V signalling, then there's no UHS */ - host->vqmmc = regulator_get(mmc_dev(mmc), "vqmmc"); + host->vqmmc = regulator_get_optional(mmc_dev(mmc), "vqmmc"); if (IS_ERR_OR_NULL(host->vqmmc)) { if (PTR_ERR(host->vqmmc) < 0) { pr_info("%s: no vqmmc regulator found\n", @@ -3042,7 +3042,7 @@ int sdhci_add_host(struct sdhci_host *host) ocr_avail = 0; - host->vmmc = regulator_get(mmc_dev(mmc), "vmmc"); + host->vmmc = regulator_get_optional(mmc_dev(mmc), "vmmc"); if (IS_ERR_OR_NULL(host->vmmc)) { if (PTR_ERR(host->vmmc) < 0) { pr_info("%s: no vmmc regulator found\n", diff --git a/drivers/regulator/88pm800.c b/drivers/regulator/88pm800.c new file mode 100644 index 000000000000..3459f60dcfd1 --- /dev/null +++ b/drivers/regulator/88pm800.c @@ -0,0 +1,383 @@ +/* + * Regulators driver for Marvell 88PM800 + * + * Copyright (C) 2012 Marvell International Ltd. + * Joseph(Yossi) Hanin + * Yi Zhang + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* LDO1 with DVC[0..3] */ +#define PM800_LDO1_VOUT (0x08) /* VOUT1 */ +#define PM800_LDO1_VOUT_2 (0x09) +#define PM800_LDO1_VOUT_3 (0x0A) +#define PM800_LDO2_VOUT (0x0B) +#define PM800_LDO3_VOUT (0x0C) +#define PM800_LDO4_VOUT (0x0D) +#define PM800_LDO5_VOUT (0x0E) +#define PM800_LDO6_VOUT (0x0F) +#define PM800_LDO7_VOUT (0x10) +#define PM800_LDO8_VOUT (0x11) +#define PM800_LDO9_VOUT (0x12) +#define PM800_LDO10_VOUT (0x13) +#define PM800_LDO11_VOUT (0x14) +#define PM800_LDO12_VOUT (0x15) +#define PM800_LDO13_VOUT (0x16) +#define PM800_LDO14_VOUT (0x17) +#define PM800_LDO15_VOUT (0x18) +#define PM800_LDO16_VOUT (0x19) +#define PM800_LDO17_VOUT (0x1A) +#define PM800_LDO18_VOUT (0x1B) +#define PM800_LDO19_VOUT (0x1C) + +/* BUCK1 with DVC[0..3] */ +#define PM800_BUCK1 (0x3C) +#define PM800_BUCK1_1 (0x3D) +#define PM800_BUCK1_2 (0x3E) +#define PM800_BUCK1_3 (0x3F) +#define PM800_BUCK2 (0x40) +#define PM800_BUCK3 (0x41) +#define PM800_BUCK3 (0x41) +#define PM800_BUCK4 (0x42) +#define PM800_BUCK4_1 (0x43) +#define PM800_BUCK4_2 (0x44) +#define PM800_BUCK4_3 (0x45) +#define PM800_BUCK5 (0x46) + +#define PM800_BUCK_ENA (0x50) +#define PM800_LDO_ENA1_1 (0x51) +#define PM800_LDO_ENA1_2 (0x52) +#define PM800_LDO_ENA1_3 (0x53) + +#define PM800_LDO_ENA2_1 (0x56) +#define PM800_LDO_ENA2_2 (0x57) +#define PM800_LDO_ENA2_3 (0x58) + +#define PM800_BUCK1_MISC1 (0x78) +#define PM800_BUCK3_MISC1 (0x7E) +#define PM800_BUCK4_MISC1 (0x81) +#define PM800_BUCK5_MISC1 (0x84) + +struct pm800_regulator_info { + struct regulator_desc desc; + int max_ua; +}; + +struct pm800_regulators { + struct regulator_dev *regulators[PM800_ID_RG_MAX]; + struct pm80x_chip *chip; + struct regmap *map; +}; + +/* + * vreg - the buck regs string. + * ereg - the string for the enable register. + * ebit - the bit number in the enable register. + * amax - the current + * Buck has 2 kinds of voltage steps. It is easy to find voltage by ranges, + * not the constant voltage table. + * n_volt - Number of available selectors + */ +#define PM800_BUCK(vreg, ereg, ebit, amax, volt_ranges, n_volt) \ +{ \ + .desc = { \ + .name = #vreg, \ + .ops = &pm800_volt_range_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = PM800_ID_##vreg, \ + .owner = THIS_MODULE, \ + .n_voltages = n_volt, \ + .linear_ranges = volt_ranges, \ + .n_linear_ranges = ARRAY_SIZE(volt_ranges), \ + .vsel_reg = PM800_##vreg, \ + .vsel_mask = 0x7f, \ + .enable_reg = PM800_##ereg, \ + .enable_mask = 1 << (ebit), \ + }, \ + .max_ua = (amax), \ +} + +/* + * vreg - the LDO regs string + * ereg - the string for the enable register. + * ebit - the bit number in the enable register. + * amax - the current + * volt_table - the LDO voltage table + * For all the LDOes, there are too many ranges. Using volt_table will be + * simpler and faster. + */ +#define PM800_LDO(vreg, ereg, ebit, amax, ldo_volt_table) \ +{ \ + .desc = { \ + .name = #vreg, \ + .ops = &pm800_volt_table_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = PM800_ID_##vreg, \ + .owner = THIS_MODULE, \ + .n_voltages = ARRAY_SIZE(ldo_volt_table), \ + .vsel_reg = PM800_##vreg##_VOUT, \ + .vsel_mask = 0x1f, \ + .enable_reg = PM800_##ereg, \ + .enable_mask = 1 << (ebit), \ + .volt_table = ldo_volt_table, \ + }, \ + .max_ua = (amax), \ +} + +/* Ranges are sorted in ascending order. */ +static const struct regulator_linear_range buck1_volt_range[] = { + { .min_uV = 600000, .max_uV = 1587500, .min_sel = 0, .max_sel = 0x4f, + .uV_step = 12500 }, + { .min_uV = 1600000, .max_uV = 1800000, .min_sel = 0x50, + .max_sel = 0x54, .uV_step = 50000 }, +}; + +/* BUCK 2~5 have same ranges. */ +static const struct regulator_linear_range buck2_5_volt_range[] = { + { .min_uV = 600000, .max_uV = 1587500, .min_sel = 0, .max_sel = 0x4f, + .uV_step = 12500 }, + { .min_uV = 1600000, .max_uV = 3300000, .min_sel = 0x50, + .max_sel = 0x72, .uV_step = 50000 }, +}; + +static const unsigned int ldo1_volt_table[] = { + 600000, 650000, 700000, 750000, 800000, 850000, 900000, 950000, + 1000000, 1050000, 1100000, 1150000, 1200000, 1300000, 1400000, 1500000, +}; + +static const unsigned int ldo2_volt_table[] = { + 1700000, 1800000, 1900000, 2000000, 2100000, 2500000, 2700000, 2800000, +}; + +/* LDO 3~17 have same voltage table. */ +static const unsigned int ldo3_17_volt_table[] = { + 1200000, 1250000, 1700000, 1800000, 1850000, 1900000, 2500000, 2600000, + 2700000, 2750000, 2800000, 2850000, 2900000, 3000000, 3100000, 3300000, +}; + +/* LDO 18~19 have same voltage table. */ +static const unsigned int ldo18_19_volt_table[] = { + 1700000, 1800000, 1900000, 2500000, 2800000, 2900000, 3100000, 3300000, +}; + +static int pm800_get_current_limit(struct regulator_dev *rdev) +{ + struct pm800_regulator_info *info = rdev_get_drvdata(rdev); + + return info->max_ua; +} + +static struct regulator_ops pm800_volt_range_ops = { + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .get_current_limit = pm800_get_current_limit, +}; + +static struct regulator_ops pm800_volt_table_ops = { + .list_voltage = regulator_list_voltage_table, + .map_voltage = regulator_map_voltage_iterate, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .get_current_limit = pm800_get_current_limit, +}; + +/* The array is indexed by id(PM800_ID_XXX) */ +static struct pm800_regulator_info pm800_regulator_info[] = { + PM800_BUCK(BUCK1, BUCK_ENA, 0, 3000000, buck1_volt_range, 0x55), + PM800_BUCK(BUCK2, BUCK_ENA, 1, 1200000, buck2_5_volt_range, 0x73), + PM800_BUCK(BUCK3, BUCK_ENA, 2, 1200000, buck2_5_volt_range, 0x73), + PM800_BUCK(BUCK4, BUCK_ENA, 3, 1200000, buck2_5_volt_range, 0x73), + PM800_BUCK(BUCK5, BUCK_ENA, 4, 1200000, buck2_5_volt_range, 0x73), + + PM800_LDO(LDO1, LDO_ENA1_1, 0, 200000, ldo1_volt_table), + PM800_LDO(LDO2, LDO_ENA1_1, 1, 10000, ldo2_volt_table), + PM800_LDO(LDO3, LDO_ENA1_1, 2, 300000, ldo3_17_volt_table), + PM800_LDO(LDO4, LDO_ENA1_1, 3, 300000, ldo3_17_volt_table), + PM800_LDO(LDO5, LDO_ENA1_1, 4, 300000, ldo3_17_volt_table), + PM800_LDO(LDO6, LDO_ENA1_1, 5, 300000, ldo3_17_volt_table), + PM800_LDO(LDO7, LDO_ENA1_1, 6, 300000, ldo3_17_volt_table), + PM800_LDO(LDO8, LDO_ENA1_1, 7, 300000, ldo3_17_volt_table), + PM800_LDO(LDO9, LDO_ENA1_2, 0, 300000, ldo3_17_volt_table), + PM800_LDO(LDO10, LDO_ENA1_2, 1, 300000, ldo3_17_volt_table), + PM800_LDO(LDO11, LDO_ENA1_2, 2, 300000, ldo3_17_volt_table), + PM800_LDO(LDO12, LDO_ENA1_2, 3, 300000, ldo3_17_volt_table), + PM800_LDO(LDO13, LDO_ENA1_2, 4, 300000, ldo3_17_volt_table), + PM800_LDO(LDO14, LDO_ENA1_2, 5, 300000, ldo3_17_volt_table), + PM800_LDO(LDO15, LDO_ENA1_2, 6, 300000, ldo3_17_volt_table), + PM800_LDO(LDO16, LDO_ENA1_2, 7, 300000, ldo3_17_volt_table), + PM800_LDO(LDO17, LDO_ENA1_3, 0, 300000, ldo3_17_volt_table), + PM800_LDO(LDO18, LDO_ENA1_3, 1, 200000, ldo18_19_volt_table), + PM800_LDO(LDO19, LDO_ENA1_3, 2, 200000, ldo18_19_volt_table), +}; + +#define PM800_REGULATOR_OF_MATCH(_name, _id) \ + [PM800_ID_##_id] = { \ + .name = #_name, \ + .driver_data = &pm800_regulator_info[PM800_ID_##_id], \ + } + +static struct of_regulator_match pm800_regulator_matches[] = { + PM800_REGULATOR_OF_MATCH(buck1, BUCK1), + PM800_REGULATOR_OF_MATCH(buck2, BUCK2), + PM800_REGULATOR_OF_MATCH(buck3, BUCK3), + PM800_REGULATOR_OF_MATCH(buck4, BUCK4), + PM800_REGULATOR_OF_MATCH(buck5, BUCK5), + PM800_REGULATOR_OF_MATCH(ldo1, LDO1), + PM800_REGULATOR_OF_MATCH(ldo2, LDO2), + PM800_REGULATOR_OF_MATCH(ldo3, LDO3), + PM800_REGULATOR_OF_MATCH(ldo4, LDO4), + PM800_REGULATOR_OF_MATCH(ldo5, LDO5), + PM800_REGULATOR_OF_MATCH(ldo6, LDO6), + PM800_REGULATOR_OF_MATCH(ldo7, LDO7), + PM800_REGULATOR_OF_MATCH(ldo8, LDO8), + PM800_REGULATOR_OF_MATCH(ldo9, LDO9), + PM800_REGULATOR_OF_MATCH(ldo10, LDO10), + PM800_REGULATOR_OF_MATCH(ldo11, LDO11), + PM800_REGULATOR_OF_MATCH(ldo12, LDO12), + PM800_REGULATOR_OF_MATCH(ldo13, LDO13), + PM800_REGULATOR_OF_MATCH(ldo14, LDO14), + PM800_REGULATOR_OF_MATCH(ldo15, LDO15), + PM800_REGULATOR_OF_MATCH(ldo16, LDO16), + PM800_REGULATOR_OF_MATCH(ldo17, LDO17), + PM800_REGULATOR_OF_MATCH(ldo18, LDO18), + PM800_REGULATOR_OF_MATCH(ldo19, LDO19), +}; + +static int pm800_regulator_dt_init(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + int ret; + + ret = of_regulator_match(&pdev->dev, np, + pm800_regulator_matches, + ARRAY_SIZE(pm800_regulator_matches)); + if (ret < 0) + return ret; + + return 0; +} + +static int pm800_regulator_probe(struct platform_device *pdev) +{ + struct pm80x_chip *chip = dev_get_drvdata(pdev->dev.parent); + struct pm80x_platform_data *pdata = dev_get_platdata(pdev->dev.parent); + struct pm800_regulators *pm800_data; + struct pm800_regulator_info *info; + struct regulator_config config = { }; + struct regulator_init_data *init_data; + int i, ret; + + if (!pdata || pdata->num_regulators == 0) { + if (IS_ENABLED(CONFIG_OF)) { + ret = pm800_regulator_dt_init(pdev); + if (ret) + return ret; + } else { + return -ENODEV; + } + } else if (pdata->num_regulators) { + unsigned int count = 0; + + /* Check whether num_regulator is valid. */ + for (i = 0; i < ARRAY_SIZE(pdata->regulators); i++) { + if (pdata->regulators[i]) + count++; + } + if (count != pdata->num_regulators) + return -EINVAL; + } else { + return -EINVAL; + } + + pm800_data = devm_kzalloc(&pdev->dev, sizeof(*pm800_data), + GFP_KERNEL); + if (!pm800_data) { + dev_err(&pdev->dev, "Failed to allocate pm800_regualtors"); + return -ENOMEM; + } + + pm800_data->map = chip->subchip->regmap_power; + pm800_data->chip = chip; + + platform_set_drvdata(pdev, pm800_data); + + for (i = 0; i < PM800_ID_RG_MAX; i++) { + if (!pdata || pdata->num_regulators == 0) + init_data = pm800_regulator_matches[i].init_data; + else + init_data = pdata->regulators[i]; + if (!init_data) + continue; + info = pm800_regulator_matches[i].driver_data; + config.dev = &pdev->dev; + config.init_data = init_data; + config.driver_data = info; + config.regmap = pm800_data->map; + config.of_node = pm800_regulator_matches[i].of_node; + + pm800_data->regulators[i] = + regulator_register(&info->desc, &config); + if (IS_ERR(pm800_data->regulators[i])) { + ret = PTR_ERR(pm800_data->regulators[i]); + dev_err(&pdev->dev, "Failed to register %s\n", + info->desc.name); + + while (--i >= 0) + regulator_unregister(pm800_data->regulators[i]); + + return ret; + } + } + + return 0; +} + +static int pm800_regulator_remove(struct platform_device *pdev) +{ + struct pm800_regulators *pm800_data = platform_get_drvdata(pdev); + int i; + + for (i = 0; i < PM800_ID_RG_MAX; i++) + regulator_unregister(pm800_data->regulators[i]); + + return 0; +} + +static struct platform_driver pm800_regulator_driver = { + .driver = { + .name = "88pm80x-regulator", + .owner = THIS_MODULE, + }, + .probe = pm800_regulator_probe, + .remove = pm800_regulator_remove, +}; + +module_platform_driver(pm800_regulator_driver); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Joseph(Yossi) Hanin "); +MODULE_DESCRIPTION("Regulator Driver for Marvell 88PM800 PMIC"); +MODULE_ALIAS("platform:88pm800-regulator"); diff --git a/drivers/regulator/88pm8607.c b/drivers/regulator/88pm8607.c index 8a7cb1f43046..70230974468c 100644 --- a/drivers/regulator/88pm8607.c +++ b/drivers/regulator/88pm8607.c @@ -346,7 +346,7 @@ static int pm8607_regulator_probe(struct platform_device *pdev) { struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent); struct pm8607_regulator_info *info = NULL; - struct regulator_init_data *pdata = pdev->dev.platform_data; + struct regulator_init_data *pdata = dev_get_platdata(&pdev->dev); struct regulator_config config = { }; struct resource *res; int i; diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig index f1e6ad98eeba..dfe58096b374 100644 --- a/drivers/regulator/Kconfig +++ b/drivers/regulator/Kconfig @@ -64,15 +64,21 @@ config REGULATOR_USERSPACE_CONSUMER If unsure, say no. -config REGULATOR_GPIO - tristate "GPIO regulator support" - depends on GPIOLIB +config REGULATOR_88PM800 + tristate "Marvell 88PM800 Power regulators" + depends on MFD_88PM800 help - This driver provides support for regulators that can be - controlled via gpios. - It is capable of supporting current and voltage regulators - and the platform has to provide a mapping of GPIO-states - to target volts/amps. + This driver supports Marvell 88PM800 voltage regulator chips. + It delivers digitally programmable output, + the voltage is programmed via I2C interface. + It's suitable to support PXA988 chips to control VCC_MAIN and + various voltages. + +config REGULATOR_88PM8607 + tristate "Marvell 88PM8607 Power regulators" + depends on MFD_88PM860X=y + help + This driver supports 88PM8607 voltage regulator chips. config REGULATOR_AD5398 tristate "Analog Devices AD5398/AD5821 regulators" @@ -81,6 +87,14 @@ config REGULATOR_AD5398 This driver supports AD5398 and AD5821 current regulator chips. If building into module, its name is ad5398.ko. +config REGULATOR_ANATOP + tristate "Freescale i.MX on-chip ANATOP LDO regulators" + depends on MFD_SYSCON + help + Say y here to support Freescale i.MX on-chip ANATOP LDOs + regulators. It is recommended that this option be + enabled on i.MX6 platform. + config REGULATOR_AAT2870 tristate "AnalogicTech AAT2870 Regulators" depends on MFD_AAT2870_CORE @@ -88,6 +102,22 @@ config REGULATOR_AAT2870 If you have a AnalogicTech AAT2870 say Y to enable the regulator driver. +config REGULATOR_AB3100 + tristate "ST-Ericsson AB3100 Regulator functions" + depends on AB3100_CORE + default y if AB3100_CORE + help + These regulators correspond to functionality in the + AB3100 analog baseband dealing with power regulators + for the system. + +config REGULATOR_AB8500 + bool "ST-Ericsson AB8500 Power Regulators" + depends on AB8500_CORE + help + This driver supports the regulators found on the ST-Ericsson mixed + signal AB8500 PMIC + config REGULATOR_ARIZONA tristate "Wolfson Arizona class devices" depends on MFD_ARIZONA @@ -96,6 +126,13 @@ config REGULATOR_ARIZONA Support for the regulators found on Wolfson Arizona class devices. +config REGULATOR_AS3711 + tristate "AS3711 PMIC" + depends on MFD_AS3711 + help + This driver provides support for the voltage regulators on the + AS3711 PMIC + config REGULATOR_DA903X tristate "Dialog Semiconductor DA9030/DA9034 regulators" depends on PMIC_DA903X @@ -120,6 +157,37 @@ config REGULATOR_DA9055 This driver can also be built as a module. If so, the module will be called da9055-regulator. +config REGULATOR_DA9063 + tristate "Dialog Semiconductor DA9063 regulators" + depends on MFD_DA9063 + help + Say y here to support the BUCKs and LDOs regulators found on + DA9063 PMICs. + + This driver can also be built as a module. If so, the module + will be called da9063-regulator. + +config REGULATOR_DA9210 + tristate "Dialog Semiconductor DA9210 regulator" + depends on I2C + select REGMAP_I2C + help + Say y here to support for the Dialog Semiconductor DA9210. + The DA9210 is a multi-phase synchronous step down + converter 12A DC-DC Buck controlled through an I2C + interface. + +config REGULATOR_DBX500_PRCMU + bool + +config REGULATOR_DB8500_PRCMU + bool "ST-Ericsson DB8500 Voltage Domain Regulators" + depends on MFD_DB8500_PRCMU + select REGULATOR_DBX500_PRCMU + help + This driver supports the voltage domain regulators controlled by the + DB8500 PRCMU + config REGULATOR_FAN53555 tristate "Fairchild FAN53555 Regulator" depends on I2C @@ -131,32 +199,15 @@ config REGULATOR_FAN53555 input voltage supply of 2.5V to 5.5V. The output voltage is programmed through an I2C interface. -config REGULATOR_ANATOP - tristate "Freescale i.MX on-chip ANATOP LDO regulators" - depends on MFD_SYSCON +config REGULATOR_GPIO + tristate "GPIO regulator support" + depends on GPIOLIB help - Say y here to support Freescale i.MX on-chip ANATOP LDOs - regulators. It is recommended that this option be - enabled on i.MX6 platform. - -config REGULATOR_MC13XXX_CORE - tristate - -config REGULATOR_MC13783 - tristate "Freescale MC13783 regulator driver" - depends on MFD_MC13783 - select REGULATOR_MC13XXX_CORE - help - Say y here to support the regulators found on the Freescale MC13783 - PMIC. - -config REGULATOR_MC13892 - tristate "Freescale MC13892 regulator driver" - depends on MFD_MC13XXX - select REGULATOR_MC13XXX_CORE - help - Say y here to support the regulators found on the Freescale MC13892 - PMIC. + This driver provides support for regulators that can be + controlled via gpios. + It is capable of supporting current and voltage regulators + and the platform has to provide a mapping of GPIO-states + to target volts/amps. config REGULATOR_ISL6271A tristate "Intersil ISL6271A Power regulator" @@ -164,11 +215,41 @@ config REGULATOR_ISL6271A help This driver supports ISL6271A voltage regulator chip. -config REGULATOR_88PM8607 - bool "Marvell 88PM8607 Power regulators" - depends on MFD_88PM860X=y +config REGULATOR_LP3971 + tristate "National Semiconductors LP3971 PMIC regulator driver" + depends on I2C help - This driver supports 88PM8607 voltage regulator chips. + Say Y here to support the voltage regulators and convertors + on National Semiconductors LP3971 PMIC + +config REGULATOR_LP3972 + tristate "National Semiconductors LP3972 PMIC regulator driver" + depends on I2C + help + Say Y here to support the voltage regulators and convertors + on National Semiconductors LP3972 PMIC + +config REGULATOR_LP872X + tristate "TI/National Semiconductor LP8720/LP8725 voltage regulators" + depends on I2C + select REGMAP_I2C + help + This driver supports LP8720/LP8725 PMIC + +config REGULATOR_LP8755 + tristate "TI LP8755 High Performance PMU driver" + depends on I2C + select REGMAP_I2C + help + This driver supports LP8755 High Performance PMU driver. This + chip contains six step-down DC/DC converters which can support + 9 mode multiphase configuration. + +config REGULATOR_LP8788 + tristate "TI LP8788 Power Regulators" + depends on MFD_LP8788 + help + This driver supports LP8788 voltage regulator chip. config REGULATOR_MAX1586 tristate "Maxim 1586/1587 voltage regulator" @@ -259,6 +340,37 @@ config REGULATOR_MAX77693 and one current regulator 'CHARGER'. This is suitable for Exynos-4x12 chips. +config REGULATOR_MC13XXX_CORE + tristate + +config REGULATOR_MC13783 + tristate "Freescale MC13783 regulator driver" + depends on MFD_MC13783 + select REGULATOR_MC13XXX_CORE + help + Say y here to support the regulators found on the Freescale MC13783 + PMIC. + +config REGULATOR_MC13892 + tristate "Freescale MC13892 regulator driver" + depends on MFD_MC13XXX + select REGULATOR_MC13XXX_CORE + help + Say y here to support the regulators found on the Freescale MC13892 + PMIC. + +config REGULATOR_PALMAS + tristate "TI Palmas PMIC Regulators" + depends on MFD_PALMAS + help + If you wish to control the regulators on the Palmas series of + chips say Y here. This will enable support for all the software + controllable SMPS/LDO regulators. + + The regulators available on Palmas series chips vary depending + on the muxing. This is handled automatically in the driver by + reading the mux info from OTP. + config REGULATOR_PCAP tristate "Motorola PCAP2 regulator driver" depends on EZX_PCAP @@ -266,42 +378,6 @@ config REGULATOR_PCAP This driver provides support for the voltage regulators of the PCAP2 PMIC. -config REGULATOR_LP3971 - tristate "National Semiconductors LP3971 PMIC regulator driver" - depends on I2C - help - Say Y here to support the voltage regulators and convertors - on National Semiconductors LP3971 PMIC - -config REGULATOR_LP3972 - tristate "National Semiconductors LP3972 PMIC regulator driver" - depends on I2C - help - Say Y here to support the voltage regulators and convertors - on National Semiconductors LP3972 PMIC - -config REGULATOR_LP872X - bool "TI/National Semiconductor LP8720/LP8725 voltage regulators" - depends on I2C=y - select REGMAP_I2C - help - This driver supports LP8720/LP8725 PMIC - -config REGULATOR_LP8755 - tristate "TI LP8755 High Performance PMU driver" - depends on I2C - select REGMAP_I2C - help - This driver supports LP8755 High Performance PMU driver. This - chip contains six step-down DC/DC converters which can support - 9 mode multiphase configuration. - -config REGULATOR_LP8788 - bool "TI LP8788 Power Regulators" - depends on MFD_LP8788 - help - This driver supports LP8788 voltage regulator chip. - config REGULATOR_PCF50633 tristate "NXP PCF50633 regulator driver" depends on MFD_PCF50633 @@ -309,6 +385,14 @@ config REGULATOR_PCF50633 Say Y here to support the voltage regulators and convertors on PCF50633 +config REGULATOR_PFUZE100 + tristate "Support regulators on Freescale PFUZE100 PMIC" + depends on I2C + select REGMAP_I2C + help + Say y here to support the regulators found on the Freescale PFUZE100 + PMIC. + config REGULATOR_RC5T583 tristate "RICOH RC5T583 Power regulators" depends on MFD_RC5T583 @@ -335,44 +419,15 @@ config REGULATOR_S5M8767 via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and supports DVS mode with 8bits of output voltage control. -config REGULATOR_AB3100 - tristate "ST-Ericsson AB3100 Regulator functions" - depends on AB3100_CORE - default y if AB3100_CORE +config REGULATOR_TI_ABB + tristate "TI Adaptive Body Bias on-chip LDO" + depends on ARCH_OMAP help - These regulators correspond to functionality in the - AB3100 analog baseband dealing with power regulators - for the system. - -config REGULATOR_AB8500 - bool "ST-Ericsson AB8500 Power Regulators" - depends on AB8500_CORE - help - This driver supports the regulators found on the ST-Ericsson mixed - signal AB8500 PMIC - -config REGULATOR_DBX500_PRCMU - bool - -config REGULATOR_DB8500_PRCMU - bool "ST-Ericsson DB8500 Voltage Domain Regulators" - depends on MFD_DB8500_PRCMU - select REGULATOR_DBX500_PRCMU - help - This driver supports the voltage domain regulators controlled by the - DB8500 PRCMU - -config REGULATOR_PALMAS - tristate "TI Palmas PMIC Regulators" - depends on MFD_PALMAS - help - If you wish to control the regulators on the Palmas series of - chips say Y here. This will enable support for all the software - controllable SMPS/LDO regulators. - - The regulators available on Palmas series chips vary depending - on the muxing. This is handled automatically in the driver by - reading the mux info from OTP. + Select this option to support Texas Instruments' on-chip Adaptive Body + Bias (ABB) LDO regulators. It is recommended that this option be + enabled on required TI SoC. Certain Operating Performance Points + on TI SoCs may be unstable without enabling this as it provides + device specific optimized bias to allow/optimize functionality. config REGULATOR_TPS51632 tristate "TI TPS51632 Power Regulator" @@ -475,22 +530,12 @@ config REGULATOR_TPS80031 output to control regulators. config REGULATOR_TWL4030 - bool "TI TWL4030/TWL5030/TWL6030/TPS659x0 PMIC" + tristate "TI TWL4030/TWL5030/TWL6030/TPS659x0 PMIC" depends on TWL4030_CORE help This driver supports the voltage regulators provided by this family of companion chips. -config REGULATOR_TI_ABB - bool "TI Adaptive Body Bias on-chip LDO" - depends on ARCH_OMAP - help - Select this option to support Texas Instruments' on-chip Adaptive Body - Bias (ABB) LDO regulators. It is recommended that this option be - enabled on required TI SoC. Certain Operating Performance Points - on TI SoCs may be unstable without enabling this as it provides - device specific optimized bias to allow/optimize functionality. - config REGULATOR_VEXPRESS tristate "Versatile Express regulators" depends on VEXPRESS_CONFIG @@ -526,12 +571,5 @@ config REGULATOR_WM8994 This driver provides support for the voltage regulators on the WM8994 CODEC. -config REGULATOR_AS3711 - tristate "AS3711 PMIC" - depends on MFD_AS3711 - help - This driver provides support for the voltage regulators on the - AS3711 PMIC - endif diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile index ba4a3cf3afec..185cce246022 100644 --- a/drivers/regulator/Makefile +++ b/drivers/regulator/Makefile @@ -3,12 +3,13 @@ # -obj-$(CONFIG_REGULATOR) += core.o dummy.o fixed-helper.o +obj-$(CONFIG_REGULATOR) += core.o dummy.o fixed-helper.o helpers.o obj-$(CONFIG_OF) += of_regulator.o obj-$(CONFIG_REGULATOR_FIXED_VOLTAGE) += fixed.o obj-$(CONFIG_REGULATOR_VIRTUAL_CONSUMER) += virtual.o obj-$(CONFIG_REGULATOR_USERSPACE_CONSUMER) += userspace-consumer.o +obj-$(CONFIG_REGULATOR_88PM800) += 88pm800.o obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o obj-$(CONFIG_REGULATOR_AAT2870) += aat2870-regulator.o obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o @@ -20,6 +21,8 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o obj-$(CONFIG_REGULATOR_DA903X) += da903x.o obj-$(CONFIG_REGULATOR_DA9052) += da9052-regulator.o obj-$(CONFIG_REGULATOR_DA9055) += da9055-regulator.o +obj-$(CONFIG_REGULATOR_DA9063) += da9063-regulator.o +obj-$(CONFIG_REGULATOR_DA9210) += da9210-regulator.o obj-$(CONFIG_REGULATOR_DBX500_PRCMU) += dbx500-prcmu.o obj-$(CONFIG_REGULATOR_DB8500_PRCMU) += db8500-prcmu.o obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o @@ -46,12 +49,14 @@ obj-$(CONFIG_REGULATOR_MC13783) += mc13783-regulator.o obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o +obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o obj-$(CONFIG_REGULATOR_PCF50633) += pcf50633-regulator.o obj-$(CONFIG_REGULATOR_RC5T583) += rc5t583-regulator.o obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o +obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o obj-$(CONFIG_REGULATOR_TPS62360) += tps62360-regulator.o obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o @@ -64,7 +69,6 @@ obj-$(CONFIG_REGULATOR_TPS65910) += tps65910-regulator.o obj-$(CONFIG_REGULATOR_TPS65912) += tps65912-regulator.o obj-$(CONFIG_REGULATOR_TPS80031) += tps80031-regulator.o obj-$(CONFIG_REGULATOR_TWL4030) += twl-regulator.o -obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o obj-$(CONFIG_REGULATOR_VEXPRESS) += vexpress.o obj-$(CONFIG_REGULATOR_WM831X) += wm831x-dcdc.o obj-$(CONFIG_REGULATOR_WM831X) += wm831x-isink.o diff --git a/drivers/regulator/aat2870-regulator.c b/drivers/regulator/aat2870-regulator.c index 8b5876356db9..881159dfcb5e 100644 --- a/drivers/regulator/aat2870-regulator.c +++ b/drivers/regulator/aat2870-regulator.c @@ -174,7 +174,7 @@ static int aat2870_regulator_probe(struct platform_device *pdev) config.dev = &pdev->dev; config.driver_data = ri; - config.init_data = pdev->dev.platform_data; + config.init_data = dev_get_platdata(&pdev->dev); rdev = regulator_register(&ri->desc, &config); if (IS_ERR(rdev)) { diff --git a/drivers/regulator/ab3100.c b/drivers/regulator/ab3100.c index 3be9e46594a1..7d5eaa874b2d 100644 --- a/drivers/regulator/ab3100.c +++ b/drivers/regulator/ab3100.c @@ -660,7 +660,7 @@ ab3100_regulator_of_probe(struct platform_device *pdev, struct device_node *np) static int ab3100_regulators_probe(struct platform_device *pdev) { - struct ab3100_platform_data *plfdata = pdev->dev.platform_data; + struct ab3100_platform_data *plfdata = dev_get_platdata(&pdev->dev); struct device_node *np = pdev->dev.of_node; int err = 0; u8 data; diff --git a/drivers/regulator/ad5398.c b/drivers/regulator/ad5398.c index 6b981b5faa70..b2b203cb6b2f 100644 --- a/drivers/regulator/ad5398.c +++ b/drivers/regulator/ad5398.c @@ -214,7 +214,7 @@ MODULE_DEVICE_TABLE(i2c, ad5398_id); static int ad5398_probe(struct i2c_client *client, const struct i2c_device_id *id) { - struct regulator_init_data *init_data = client->dev.platform_data; + struct regulator_init_data *init_data = dev_get_platdata(&client->dev); struct regulator_config config = { }; struct ad5398_chip_info *chip; const struct ad5398_current_data_format *df = diff --git a/drivers/regulator/as3711-regulator.c b/drivers/regulator/as3711-regulator.c index 3da6bd6950cf..8406cd745da2 100644 --- a/drivers/regulator/as3711-regulator.c +++ b/drivers/regulator/as3711-regulator.c @@ -30,102 +30,6 @@ struct as3711_regulator { struct regulator_dev *rdev; }; -static int as3711_list_voltage_sd(struct regulator_dev *rdev, - unsigned int selector) -{ - if (selector >= rdev->desc->n_voltages) - return -EINVAL; - - if (!selector) - return 0; - if (selector < 0x41) - return 600000 + selector * 12500; - if (selector < 0x71) - return 1400000 + (selector - 0x40) * 25000; - return 2600000 + (selector - 0x70) * 50000; -} - -static int as3711_list_voltage_aldo(struct regulator_dev *rdev, - unsigned int selector) -{ - if (selector >= rdev->desc->n_voltages) - return -EINVAL; - - if (selector < 0x10) - return 1200000 + selector * 50000; - return 1800000 + (selector - 0x10) * 100000; -} - -static int as3711_list_voltage_dldo(struct regulator_dev *rdev, - unsigned int selector) -{ - if (selector >= rdev->desc->n_voltages || - (selector > 0x10 && selector < 0x20)) - return -EINVAL; - - if (selector < 0x11) - return 900000 + selector * 50000; - return 1750000 + (selector - 0x20) * 50000; -} - -static int as3711_bound_check(struct regulator_dev *rdev, - int *min_uV, int *max_uV) -{ - struct as3711_regulator *reg = rdev_get_drvdata(rdev); - struct as3711_regulator_info *info = reg->reg_info; - - dev_dbg(&rdev->dev, "%s(), %d, %d, %d\n", __func__, - *min_uV, rdev->desc->min_uV, info->max_uV); - - if (*max_uV < *min_uV || - *min_uV > info->max_uV || rdev->desc->min_uV > *max_uV) - return -EINVAL; - - if (rdev->desc->n_voltages == 1) - return 0; - - if (*max_uV > info->max_uV) - *max_uV = info->max_uV; - - if (*min_uV < rdev->desc->min_uV) - *min_uV = rdev->desc->min_uV; - - return *min_uV; -} - -static int as3711_sel_check(int min, int max, int bottom, int step) -{ - int sel, voltage; - - /* Round up min, when dividing: keeps us within the range */ - sel = DIV_ROUND_UP(min - bottom, step); - voltage = sel * step + bottom; - pr_debug("%s(): select %d..%d in %d+N*%d: %d\n", __func__, - min, max, bottom, step, sel); - if (voltage > max) - return -EINVAL; - - return sel; -} - -static int as3711_map_voltage_sd(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int ret; - - ret = as3711_bound_check(rdev, &min_uV, &max_uV); - if (ret <= 0) - return ret; - - if (min_uV <= 1400000) - return as3711_sel_check(min_uV, max_uV, 600000, 12500); - - if (min_uV <= 2600000) - return as3711_sel_check(min_uV, max_uV, 1400000, 25000) + 0x40; - - return as3711_sel_check(min_uV, max_uV, 2600000, 50000) + 0x70; -} - /* * The regulator API supports 4 modes of operataion: FAST, NORMAL, IDLE and * STANDBY. We map them in the following way to AS3711 SD1-4 DCDC modes: @@ -180,44 +84,14 @@ static unsigned int as3711_get_mode_sd(struct regulator_dev *rdev) return -EINVAL; } -static int as3711_map_voltage_aldo(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int ret; - - ret = as3711_bound_check(rdev, &min_uV, &max_uV); - if (ret <= 0) - return ret; - - if (min_uV <= 1800000) - return as3711_sel_check(min_uV, max_uV, 1200000, 50000); - - return as3711_sel_check(min_uV, max_uV, 1800000, 100000) + 0x10; -} - -static int as3711_map_voltage_dldo(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int ret; - - ret = as3711_bound_check(rdev, &min_uV, &max_uV); - if (ret <= 0) - return ret; - - if (min_uV <= 1700000) - return as3711_sel_check(min_uV, max_uV, 900000, 50000); - - return as3711_sel_check(min_uV, max_uV, 1750000, 50000) + 0x20; -} - static struct regulator_ops as3711_sd_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, - .list_voltage = as3711_list_voltage_sd, - .map_voltage = as3711_map_voltage_sd, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, .get_mode = as3711_get_mode_sd, .set_mode = as3711_set_mode_sd, }; @@ -228,8 +102,8 @@ static struct regulator_ops as3711_aldo_ops = { .disable = regulator_disable_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, - .list_voltage = as3711_list_voltage_aldo, - .map_voltage = as3711_map_voltage_aldo, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, }; static struct regulator_ops as3711_dldo_ops = { @@ -238,8 +112,31 @@ static struct regulator_ops as3711_dldo_ops = { .disable = regulator_disable_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, - .list_voltage = as3711_list_voltage_dldo, - .map_voltage = as3711_map_voltage_dldo, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, +}; + +static const struct regulator_linear_range as3711_sd_ranges[] = { + { .min_uV = 612500, .max_uV = 1400000, + .min_sel = 0x1, .max_sel = 0x40, .uV_step = 12500 }, + { .min_uV = 1425000, .max_uV = 2600000, + .min_sel = 0x41, .max_sel = 0x70, .uV_step = 25000 }, + { .min_uV = 2650000, .max_uV = 3350000, + .min_sel = 0x71, .max_sel = 0x7f, .uV_step = 50000 }, +}; + +static const struct regulator_linear_range as3711_aldo_ranges[] = { + { .min_uV = 1200000, .max_uV = 1950000, + .min_sel = 0, .max_sel = 0xf, .uV_step = 50000 }, + { .min_uV = 1800000, .max_uV = 3300000, + .min_sel = 0x10, .max_sel = 0x1f, .uV_step = 100000 }, +}; + +static const struct regulator_linear_range as3711_dldo_ranges[] = { + { .min_uV = 900000, .max_uV = 1700000, + .min_sel = 0, .max_sel = 0x10, .uV_step = 50000 }, + { .min_uV = 1750000, .max_uV = 3300000, + .min_sel = 0x20, .max_sel = 0x3f, .uV_step = 50000 }, }; #define AS3711_REG(_id, _en_reg, _en_bit, _vmask, _vshift, _min_uV, _max_uV, _sfx) \ @@ -256,6 +153,8 @@ static struct regulator_ops as3711_dldo_ops = { .enable_reg = AS3711_ ## _en_reg, \ .enable_mask = BIT(_en_bit), \ .min_uV = _min_uV, \ + .linear_ranges = as3711_ ## _sfx ## _ranges, \ + .n_linear_ranges = ARRAY_SIZE(as3711_ ## _sfx ## _ranges), \ }, \ .max_uV = _max_uV, \ } diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c index 288c75abc190..a01b8b3b70ca 100644 --- a/drivers/regulator/core.c +++ b/drivers/regulator/core.c @@ -323,13 +323,14 @@ static ssize_t regulator_uA_show(struct device *dev, } static DEVICE_ATTR(microamps, 0444, regulator_uA_show, NULL); -static ssize_t regulator_name_show(struct device *dev, - struct device_attribute *attr, char *buf) +static ssize_t name_show(struct device *dev, struct device_attribute *attr, + char *buf) { struct regulator_dev *rdev = dev_get_drvdata(dev); return sprintf(buf, "%s\n", rdev_get_name(rdev)); } +static DEVICE_ATTR_RO(name); static ssize_t regulator_print_opmode(char *buf, int mode) { @@ -489,15 +490,16 @@ static ssize_t regulator_total_uA_show(struct device *dev, } static DEVICE_ATTR(requested_microamps, 0444, regulator_total_uA_show, NULL); -static ssize_t regulator_num_users_show(struct device *dev, - struct device_attribute *attr, char *buf) +static ssize_t num_users_show(struct device *dev, struct device_attribute *attr, + char *buf) { struct regulator_dev *rdev = dev_get_drvdata(dev); return sprintf(buf, "%d\n", rdev->use_count); } +static DEVICE_ATTR_RO(num_users); -static ssize_t regulator_type_show(struct device *dev, - struct device_attribute *attr, char *buf) +static ssize_t type_show(struct device *dev, struct device_attribute *attr, + char *buf) { struct regulator_dev *rdev = dev_get_drvdata(dev); @@ -509,6 +511,7 @@ static ssize_t regulator_type_show(struct device *dev, } return sprintf(buf, "unknown\n"); } +static DEVICE_ATTR_RO(type); static ssize_t regulator_suspend_mem_uV_show(struct device *dev, struct device_attribute *attr, char *buf) @@ -632,12 +635,13 @@ static DEVICE_ATTR(bypass, 0444, * These are the only attributes are present for all regulators. * Other attributes are a function of regulator functionality. */ -static struct device_attribute regulator_dev_attrs[] = { - __ATTR(name, 0444, regulator_name_show, NULL), - __ATTR(num_users, 0444, regulator_num_users_show, NULL), - __ATTR(type, 0444, regulator_type_show, NULL), - __ATTR_NULL, +static struct attribute *regulator_dev_attrs[] = { + &dev_attr_name.attr, + &dev_attr_num_users.attr, + &dev_attr_type.attr, + NULL, }; +ATTRIBUTE_GROUPS(regulator_dev); static void regulator_dev_release(struct device *dev) { @@ -648,7 +652,7 @@ static void regulator_dev_release(struct device *dev) static struct class regulator_class = { .name = "regulator", .dev_release = regulator_dev_release, - .dev_attrs = regulator_dev_attrs, + .dev_groups = regulator_dev_groups, }; /* Calculate the new optimum regulator operating mode based on the new total @@ -984,7 +988,8 @@ static int set_machine_constraints(struct regulator_dev *rdev, } } - if (rdev->constraints->ramp_delay && ops->set_ramp_delay) { + if ((rdev->constraints->ramp_delay || rdev->constraints->ramp_disable) + && ops->set_ramp_delay) { ret = ops->set_ramp_delay(rdev, rdev->constraints->ramp_delay); if (ret < 0) { rdev_err(rdev, "failed to set ramp_delay\n"); @@ -1238,7 +1243,7 @@ static struct regulator_dev *regulator_dev_lookup(struct device *dev, /* Internal regulator request function */ static struct regulator *_regulator_get(struct device *dev, const char *id, - int exclusive) + bool exclusive) { struct regulator_dev *rdev; struct regulator *regulator = ERR_PTR(-EPROBE_DEFER); @@ -1344,7 +1349,7 @@ out: */ struct regulator *regulator_get(struct device *dev, const char *id) { - return _regulator_get(dev, id, 0); + return _regulator_get(dev, id, false); } EXPORT_SYMBOL_GPL(regulator_get); @@ -1405,10 +1410,69 @@ EXPORT_SYMBOL_GPL(devm_regulator_get); */ struct regulator *regulator_get_exclusive(struct device *dev, const char *id) { - return _regulator_get(dev, id, 1); + return _regulator_get(dev, id, true); } EXPORT_SYMBOL_GPL(regulator_get_exclusive); +/** + * regulator_get_optional - obtain optional access to a regulator. + * @dev: device for regulator "consumer" + * @id: Supply name or regulator ID. + * + * Returns a struct regulator corresponding to the regulator producer, + * or IS_ERR() condition containing errno. Other consumers will be + * unable to obtain this reference is held and the use count for the + * regulator will be initialised to reflect the current state of the + * regulator. + * + * This is intended for use by consumers for devices which can have + * some supplies unconnected in normal use, such as some MMC devices. + * It can allow the regulator core to provide stub supplies for other + * supplies requested using normal regulator_get() calls without + * disrupting the operation of drivers that can handle absent + * supplies. + * + * Use of supply names configured via regulator_set_device_supply() is + * strongly encouraged. It is recommended that the supply name used + * should match the name used for the supply and/or the relevant + * device pins in the datasheet. + */ +struct regulator *regulator_get_optional(struct device *dev, const char *id) +{ + return _regulator_get(dev, id, 0); +} +EXPORT_SYMBOL_GPL(regulator_get_optional); + +/** + * devm_regulator_get_optional - Resource managed regulator_get_optional() + * @dev: device for regulator "consumer" + * @id: Supply name or regulator ID. + * + * Managed regulator_get_optional(). Regulators returned from this + * function are automatically regulator_put() on driver detach. See + * regulator_get_optional() for more information. + */ +struct regulator *devm_regulator_get_optional(struct device *dev, + const char *id) +{ + struct regulator **ptr, *regulator; + + ptr = devres_alloc(devm_regulator_release, sizeof(*ptr), GFP_KERNEL); + if (!ptr) + return ERR_PTR(-ENOMEM); + + regulator = regulator_get_optional(dev, id); + if (!IS_ERR(regulator)) { + *ptr = regulator; + devres_add(dev, ptr); + } else { + devres_free(ptr); + } + + return regulator; +} +EXPORT_SYMBOL_GPL(devm_regulator_get_optional); + /* Locks held by regulator_put() */ static void _regulator_put(struct regulator *regulator) { @@ -1434,6 +1498,36 @@ static void _regulator_put(struct regulator *regulator) module_put(rdev->owner); } +/** + * devm_regulator_get_exclusive - Resource managed regulator_get_exclusive() + * @dev: device for regulator "consumer" + * @id: Supply name or regulator ID. + * + * Managed regulator_get_exclusive(). Regulators returned from this function + * are automatically regulator_put() on driver detach. See regulator_get() for + * more information. + */ +struct regulator *devm_regulator_get_exclusive(struct device *dev, + const char *id) +{ + struct regulator **ptr, *regulator; + + ptr = devres_alloc(devm_regulator_release, sizeof(*ptr), GFP_KERNEL); + if (!ptr) + return ERR_PTR(-ENOMEM); + + regulator = _regulator_get(dev, id, 1); + if (!IS_ERR(regulator)) { + *ptr = regulator; + devres_add(dev, ptr); + } else { + devres_free(ptr); + } + + return regulator; +} +EXPORT_SYMBOL_GPL(devm_regulator_get_exclusive); + /** * regulator_put - "free" the regulator source * @regulator: regulator source @@ -1890,8 +1984,9 @@ int regulator_disable_deferred(struct regulator *regulator, int ms) rdev->deferred_disables++; mutex_unlock(&rdev->mutex); - ret = schedule_delayed_work(&rdev->disable_work, - msecs_to_jiffies(ms)); + ret = queue_delayed_work(system_power_efficient_wq, + &rdev->disable_work, + msecs_to_jiffies(ms)); if (ret < 0) return ret; else @@ -1899,77 +1994,6 @@ int regulator_disable_deferred(struct regulator *regulator, int ms) } EXPORT_SYMBOL_GPL(regulator_disable_deferred); -/** - * regulator_is_enabled_regmap - standard is_enabled() for regmap users - * - * @rdev: regulator to operate on - * - * Regulators that use regmap for their register I/O can set the - * enable_reg and enable_mask fields in their descriptor and then use - * this as their is_enabled operation, saving some code. - */ -int regulator_is_enabled_regmap(struct regulator_dev *rdev) -{ - unsigned int val; - int ret; - - ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val); - if (ret != 0) - return ret; - - if (rdev->desc->enable_is_inverted) - return (val & rdev->desc->enable_mask) == 0; - else - return (val & rdev->desc->enable_mask) != 0; -} -EXPORT_SYMBOL_GPL(regulator_is_enabled_regmap); - -/** - * regulator_enable_regmap - standard enable() for regmap users - * - * @rdev: regulator to operate on - * - * Regulators that use regmap for their register I/O can set the - * enable_reg and enable_mask fields in their descriptor and then use - * this as their enable() operation, saving some code. - */ -int regulator_enable_regmap(struct regulator_dev *rdev) -{ - unsigned int val; - - if (rdev->desc->enable_is_inverted) - val = 0; - else - val = rdev->desc->enable_mask; - - return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, - rdev->desc->enable_mask, val); -} -EXPORT_SYMBOL_GPL(regulator_enable_regmap); - -/** - * regulator_disable_regmap - standard disable() for regmap users - * - * @rdev: regulator to operate on - * - * Regulators that use regmap for their register I/O can set the - * enable_reg and enable_mask fields in their descriptor and then use - * this as their disable() operation, saving some code. - */ -int regulator_disable_regmap(struct regulator_dev *rdev) -{ - unsigned int val; - - if (rdev->desc->enable_is_inverted) - val = rdev->desc->enable_mask; - else - val = 0; - - return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, - rdev->desc->enable_mask, val); -} -EXPORT_SYMBOL_GPL(regulator_disable_regmap); - static int _regulator_is_enabled(struct regulator_dev *rdev) { /* A GPIO control always takes precedence */ @@ -2054,55 +2078,6 @@ int regulator_count_voltages(struct regulator *regulator) } EXPORT_SYMBOL_GPL(regulator_count_voltages); -/** - * regulator_list_voltage_linear - List voltages with simple calculation - * - * @rdev: Regulator device - * @selector: Selector to convert into a voltage - * - * Regulators with a simple linear mapping between voltages and - * selectors can set min_uV and uV_step in the regulator descriptor - * and then use this function as their list_voltage() operation, - */ -int regulator_list_voltage_linear(struct regulator_dev *rdev, - unsigned int selector) -{ - if (selector >= rdev->desc->n_voltages) - return -EINVAL; - if (selector < rdev->desc->linear_min_sel) - return 0; - - selector -= rdev->desc->linear_min_sel; - - return rdev->desc->min_uV + (rdev->desc->uV_step * selector); -} -EXPORT_SYMBOL_GPL(regulator_list_voltage_linear); - -/** - * regulator_list_voltage_table - List voltages with table based mapping - * - * @rdev: Regulator device - * @selector: Selector to convert into a voltage - * - * Regulators with table based mapping between voltages and - * selectors can set volt_table in the regulator descriptor - * and then use this function as their list_voltage() operation. - */ -int regulator_list_voltage_table(struct regulator_dev *rdev, - unsigned int selector) -{ - if (!rdev->desc->volt_table) { - BUG_ON(!rdev->desc->volt_table); - return -EINVAL; - } - - if (selector >= rdev->desc->n_voltages) - return -EINVAL; - - return rdev->desc->volt_table[selector]; -} -EXPORT_SYMBOL_GPL(regulator_list_voltage_table); - /** * regulator_list_voltage - enumerate supported voltages * @regulator: regulator source @@ -2197,177 +2172,6 @@ int regulator_is_supported_voltage(struct regulator *regulator, } EXPORT_SYMBOL_GPL(regulator_is_supported_voltage); -/** - * regulator_get_voltage_sel_regmap - standard get_voltage_sel for regmap users - * - * @rdev: regulator to operate on - * - * Regulators that use regmap for their register I/O can set the - * vsel_reg and vsel_mask fields in their descriptor and then use this - * as their get_voltage_vsel operation, saving some code. - */ -int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev) -{ - unsigned int val; - int ret; - - ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val); - if (ret != 0) - return ret; - - val &= rdev->desc->vsel_mask; - val >>= ffs(rdev->desc->vsel_mask) - 1; - - return val; -} -EXPORT_SYMBOL_GPL(regulator_get_voltage_sel_regmap); - -/** - * regulator_set_voltage_sel_regmap - standard set_voltage_sel for regmap users - * - * @rdev: regulator to operate on - * @sel: Selector to set - * - * Regulators that use regmap for their register I/O can set the - * vsel_reg and vsel_mask fields in their descriptor and then use this - * as their set_voltage_vsel operation, saving some code. - */ -int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel) -{ - int ret; - - sel <<= ffs(rdev->desc->vsel_mask) - 1; - - ret = regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg, - rdev->desc->vsel_mask, sel); - if (ret) - return ret; - - if (rdev->desc->apply_bit) - ret = regmap_update_bits(rdev->regmap, rdev->desc->apply_reg, - rdev->desc->apply_bit, - rdev->desc->apply_bit); - return ret; -} -EXPORT_SYMBOL_GPL(regulator_set_voltage_sel_regmap); - -/** - * regulator_map_voltage_iterate - map_voltage() based on list_voltage() - * - * @rdev: Regulator to operate on - * @min_uV: Lower bound for voltage - * @max_uV: Upper bound for voltage - * - * Drivers implementing set_voltage_sel() and list_voltage() can use - * this as their map_voltage() operation. It will find a suitable - * voltage by calling list_voltage() until it gets something in bounds - * for the requested voltages. - */ -int regulator_map_voltage_iterate(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int best_val = INT_MAX; - int selector = 0; - int i, ret; - - /* Find the smallest voltage that falls within the specified - * range. - */ - for (i = 0; i < rdev->desc->n_voltages; i++) { - ret = rdev->desc->ops->list_voltage(rdev, i); - if (ret < 0) - continue; - - if (ret < best_val && ret >= min_uV && ret <= max_uV) { - best_val = ret; - selector = i; - } - } - - if (best_val != INT_MAX) - return selector; - else - return -EINVAL; -} -EXPORT_SYMBOL_GPL(regulator_map_voltage_iterate); - -/** - * regulator_map_voltage_ascend - map_voltage() for ascendant voltage list - * - * @rdev: Regulator to operate on - * @min_uV: Lower bound for voltage - * @max_uV: Upper bound for voltage - * - * Drivers that have ascendant voltage list can use this as their - * map_voltage() operation. - */ -int regulator_map_voltage_ascend(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int i, ret; - - for (i = 0; i < rdev->desc->n_voltages; i++) { - ret = rdev->desc->ops->list_voltage(rdev, i); - if (ret < 0) - continue; - - if (ret > max_uV) - break; - - if (ret >= min_uV && ret <= max_uV) - return i; - } - - return -EINVAL; -} -EXPORT_SYMBOL_GPL(regulator_map_voltage_ascend); - -/** - * regulator_map_voltage_linear - map_voltage() for simple linear mappings - * - * @rdev: Regulator to operate on - * @min_uV: Lower bound for voltage - * @max_uV: Upper bound for voltage - * - * Drivers providing min_uV and uV_step in their regulator_desc can - * use this as their map_voltage() operation. - */ -int regulator_map_voltage_linear(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int ret, voltage; - - /* Allow uV_step to be 0 for fixed voltage */ - if (rdev->desc->n_voltages == 1 && rdev->desc->uV_step == 0) { - if (min_uV <= rdev->desc->min_uV && rdev->desc->min_uV <= max_uV) - return 0; - else - return -EINVAL; - } - - if (!rdev->desc->uV_step) { - BUG_ON(!rdev->desc->uV_step); - return -EINVAL; - } - - if (min_uV < rdev->desc->min_uV) - min_uV = rdev->desc->min_uV; - - ret = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step); - if (ret < 0) - return ret; - - ret += rdev->desc->linear_min_sel; - - /* Map back into a voltage to verify we're still in bounds */ - voltage = rdev->desc->ops->list_voltage(rdev, ret); - if (voltage < min_uV || voltage > max_uV) - return -EINVAL; - - return ret; -} -EXPORT_SYMBOL_GPL(regulator_map_voltage_linear); - static int _regulator_do_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV) { @@ -2438,8 +2242,8 @@ static int _regulator_do_set_voltage(struct regulator_dev *rdev, } /* Call set_voltage_time_sel if successfully obtained old_selector */ - if (ret == 0 && _regulator_is_enabled(rdev) && old_selector >= 0 && - old_selector != selector && rdev->desc->ops->set_voltage_time_sel) { + if (ret == 0 && !rdev->constraints->ramp_disable && old_selector >= 0 + && old_selector != selector) { delay = rdev->desc->ops->set_voltage_time_sel(rdev, old_selector, selector); @@ -2970,47 +2774,6 @@ out: } EXPORT_SYMBOL_GPL(regulator_set_optimum_mode); -/** - * regulator_set_bypass_regmap - Default set_bypass() using regmap - * - * @rdev: device to operate on. - * @enable: state to set. - */ -int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable) -{ - unsigned int val; - - if (enable) - val = rdev->desc->bypass_mask; - else - val = 0; - - return regmap_update_bits(rdev->regmap, rdev->desc->bypass_reg, - rdev->desc->bypass_mask, val); -} -EXPORT_SYMBOL_GPL(regulator_set_bypass_regmap); - -/** - * regulator_get_bypass_regmap - Default get_bypass() using regmap - * - * @rdev: device to operate on. - * @enable: current state. - */ -int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable) -{ - unsigned int val; - int ret; - - ret = regmap_read(rdev->regmap, rdev->desc->bypass_reg, &val); - if (ret != 0) - return ret; - - *enable = val & rdev->desc->bypass_mask; - - return 0; -} -EXPORT_SYMBOL_GPL(regulator_get_bypass_regmap); - /** * regulator_allow_bypass - allow the regulator to go into bypass mode * @@ -3740,8 +3503,11 @@ void regulator_unregister(struct regulator_dev *rdev) if (rdev == NULL) return; - if (rdev->supply) + if (rdev->supply) { + while (rdev->use_count--) + regulator_disable(rdev->supply); regulator_put(rdev->supply); + } mutex_lock(®ulator_list_mutex); debugfs_remove_recursive(rdev->debugfs); flush_work(&rdev->disable_work.work); diff --git a/drivers/regulator/da903x.c b/drivers/regulator/da903x.c index 2afa5730f324..f06854cf8cf5 100644 --- a/drivers/regulator/da903x.c +++ b/drivers/regulator/da903x.c @@ -252,39 +252,12 @@ static int da9034_set_dvc_voltage_sel(struct regulator_dev *rdev, return ret; } -static int da9034_map_ldo12_voltage(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - struct da903x_regulator_info *info = rdev_get_drvdata(rdev); - int sel; - - if (check_range(info, min_uV, max_uV)) { - pr_err("invalid voltage range (%d, %d) uV\n", min_uV, max_uV); - return -EINVAL; - } - - sel = DIV_ROUND_UP(min_uV - info->desc.min_uV, info->desc.uV_step); - sel = (sel >= 20) ? sel - 12 : ((sel > 7) ? 8 : sel); - - return sel; -} - -static int da9034_list_ldo12_voltage(struct regulator_dev *rdev, - unsigned selector) -{ - struct da903x_regulator_info *info = rdev_get_drvdata(rdev); - int volt; - - if (selector >= 8) - volt = 2700000 + rdev->desc->uV_step * (selector - 8); - else - volt = rdev->desc->min_uV + rdev->desc->uV_step * selector; - - if (volt > info->max_uV) - return -EINVAL; - - return volt; -} +static const struct regulator_linear_range da9034_ldo12_ranges[] = { + { .min_uV = 1700000, .max_uV = 2050000, .min_sel = 0, .max_sel = 7, + .uV_step = 50000 }, + { .min_uV = 2700000, .max_uV = 3050000, .min_sel = 8, .max_sel = 15, + .uV_step = 50000 }, +}; static struct regulator_ops da903x_regulator_ldo_ops = { .set_voltage_sel = da903x_set_voltage_sel, @@ -332,8 +305,8 @@ static struct regulator_ops da9034_regulator_dvc_ops = { static struct regulator_ops da9034_regulator_ldo12_ops = { .set_voltage_sel = da903x_set_voltage_sel, .get_voltage_sel = da903x_get_voltage_sel, - .list_voltage = da9034_list_ldo12_voltage, - .map_voltage = da9034_map_ldo12_voltage, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, .enable = da903x_enable, .disable = da903x_disable, .is_enabled = da903x_is_enabled, @@ -476,6 +449,8 @@ static int da903x_regulator_probe(struct platform_device *pdev) if (ri->desc.id == DA9034_ID_LDO12) { ri->desc.ops = &da9034_regulator_ldo12_ops; ri->desc.n_voltages = 16; + ri->desc.linear_ranges = da9034_ldo12_ranges; + ri->desc.n_linear_ranges = ARRAY_SIZE(da9034_ldo12_ranges); } if (ri->desc.id == DA9030_ID_LDO14) @@ -485,7 +460,7 @@ static int da903x_regulator_probe(struct platform_device *pdev) ri->desc.ops = &da9030_regulator_ldo1_15_ops; config.dev = &pdev->dev; - config.init_data = pdev->dev.platform_data; + config.init_data = dev_get_platdata(&pdev->dev); config.driver_data = ri; rdev = regulator_register(&ri->desc, &config); diff --git a/drivers/regulator/da9052-regulator.c b/drivers/regulator/da9052-regulator.c index 96b569abb46c..1e4d483f6163 100644 --- a/drivers/regulator/da9052-regulator.c +++ b/drivers/regulator/da9052-regulator.c @@ -349,7 +349,7 @@ static int da9052_regulator_probe(struct platform_device *pdev) return -ENOMEM; da9052 = dev_get_drvdata(pdev->dev.parent); - pdata = da9052->dev->platform_data; + pdata = dev_get_platdata(da9052->dev); regulator->da9052 = da9052; regulator->info = find_regulator_info(regulator->da9052->chip_id, diff --git a/drivers/regulator/da9055-regulator.c b/drivers/regulator/da9055-regulator.c index 30221099d09c..77b53e5a231c 100644 --- a/drivers/regulator/da9055-regulator.c +++ b/drivers/regulator/da9055-regulator.c @@ -535,7 +535,7 @@ static int da9055_regulator_probe(struct platform_device *pdev) struct regulator_config config = { }; struct da9055_regulator *regulator; struct da9055 *da9055 = dev_get_drvdata(pdev->dev.parent); - struct da9055_pdata *pdata = da9055->dev->platform_data; + struct da9055_pdata *pdata = dev_get_platdata(da9055->dev); int ret, irq; if (pdata == NULL || pdata->regulators[pdev->id] == NULL) diff --git a/drivers/regulator/da9063-regulator.c b/drivers/regulator/da9063-regulator.c new file mode 100644 index 000000000000..1a7816390773 --- /dev/null +++ b/drivers/regulator/da9063-regulator.c @@ -0,0 +1,934 @@ +/* + * Regulator driver for DA9063 PMIC series + * + * Copyright 2012 Dialog Semiconductors Ltd. + * Copyright 2013 Philipp Zabel, Pengutronix + * + * Author: Krystian Garbaciak + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + + +/* Definition for registering regmap bit fields using a mask */ +#define BFIELD(_reg, _mask) \ + REG_FIELD(_reg, __builtin_ffs((int)_mask) - 1, \ + sizeof(unsigned int) * 8 - __builtin_clz((_mask)) - 1) + +/* Regulator capabilities and registers description */ +struct da9063_regulator_info { + struct regulator_desc desc; + + /* Current limiting */ + unsigned n_current_limits; + const int *current_limits; + + /* DA9063 main register fields */ + struct reg_field mode; /* buck mode of operation */ + struct reg_field suspend; + struct reg_field sleep; + struct reg_field suspend_sleep; + unsigned int suspend_vsel_reg; + struct reg_field ilimit; + + /* DA9063 event detection bit */ + struct reg_field oc_event; +}; + +/* Macros for LDO */ +#define DA9063_LDO(chip, regl_name, min_mV, step_mV, max_mV) \ + .desc.id = chip##_ID_##regl_name, \ + .desc.name = __stringify(chip##_##regl_name), \ + .desc.ops = &da9063_ldo_ops, \ + .desc.min_uV = (min_mV) * 1000, \ + .desc.uV_step = (step_mV) * 1000, \ + .desc.n_voltages = (((max_mV) - (min_mV))/(step_mV) + 1), \ + .desc.enable_reg = DA9063_REG_##regl_name##_CONT, \ + .desc.enable_mask = DA9063_LDO_EN, \ + .desc.vsel_reg = DA9063_REG_V##regl_name##_A, \ + .desc.vsel_mask = DA9063_V##regl_name##_MASK, \ + .desc.linear_min_sel = DA9063_V##regl_name##_BIAS, \ + .sleep = BFIELD(DA9063_REG_V##regl_name##_A, DA9063_LDO_SL), \ + .suspend_sleep = BFIELD(DA9063_REG_V##regl_name##_B, DA9063_LDO_SL), \ + .suspend_vsel_reg = DA9063_REG_V##regl_name##_B + +/* Macros for voltage DC/DC converters (BUCKs) */ +#define DA9063_BUCK(chip, regl_name, min_mV, step_mV, max_mV, limits_array) \ + .desc.id = chip##_ID_##regl_name, \ + .desc.name = __stringify(chip##_##regl_name), \ + .desc.ops = &da9063_buck_ops, \ + .desc.min_uV = (min_mV) * 1000, \ + .desc.uV_step = (step_mV) * 1000, \ + .desc.n_voltages = ((max_mV) - (min_mV))/(step_mV) + 1, \ + .current_limits = limits_array, \ + .n_current_limits = ARRAY_SIZE(limits_array) + +#define DA9063_BUCK_COMMON_FIELDS(regl_name) \ + .desc.enable_reg = DA9063_REG_##regl_name##_CONT, \ + .desc.enable_mask = DA9063_BUCK_EN, \ + .desc.vsel_reg = DA9063_REG_V##regl_name##_A, \ + .desc.vsel_mask = DA9063_VBUCK_MASK, \ + .desc.linear_min_sel = DA9063_VBUCK_BIAS, \ + .sleep = BFIELD(DA9063_REG_V##regl_name##_A, DA9063_BUCK_SL), \ + .suspend_sleep = BFIELD(DA9063_REG_V##regl_name##_B, DA9063_BUCK_SL), \ + .suspend_vsel_reg = DA9063_REG_V##regl_name##_B, \ + .mode = BFIELD(DA9063_REG_##regl_name##_CFG, DA9063_BUCK_MODE_MASK) + +/* Defines asignment of regulators info table to chip model */ +struct da9063_dev_model { + const struct da9063_regulator_info *regulator_info; + unsigned n_regulators; + unsigned dev_model; +}; + +/* Single regulator settings */ +struct da9063_regulator { + struct regulator_desc desc; + struct regulator_dev *rdev; + struct da9063 *hw; + const struct da9063_regulator_info *info; + + struct regmap_field *mode; + struct regmap_field *suspend; + struct regmap_field *sleep; + struct regmap_field *suspend_sleep; + struct regmap_field *ilimit; +}; + +/* Encapsulates all information for the regulators driver */ +struct da9063_regulators { + int irq_ldo_lim; + int irq_uvov; + + unsigned n_regulators; + /* Array size to be defined during init. Keep at end. */ + struct da9063_regulator regulator[0]; +}; + +/* BUCK modes for DA9063 */ +enum { + BUCK_MODE_MANUAL, /* 0 */ + BUCK_MODE_SLEEP, /* 1 */ + BUCK_MODE_SYNC, /* 2 */ + BUCK_MODE_AUTO /* 3 */ +}; + +/* Regulator operations */ + +/* Current limits array (in uA) for BCORE1, BCORE2, BPRO. + Entry indexes corresponds to register values. */ +static const int da9063_buck_a_limits[] = { + 500000, 600000, 700000, 800000, 900000, 1000000, 1100000, 1200000, + 1300000, 1400000, 1500000, 1600000, 1700000, 1800000, 1900000, 2000000 +}; + +/* Current limits array (in uA) for BMEM, BIO, BPERI. + Entry indexes corresponds to register values. */ +static const int da9063_buck_b_limits[] = { + 1500000, 1600000, 1700000, 1800000, 1900000, 2000000, 2100000, 2200000, + 2300000, 2400000, 2500000, 2600000, 2700000, 2800000, 2900000, 3000000 +}; + +/* Current limits array (in uA) for merged BCORE1 and BCORE2. + Entry indexes corresponds to register values. */ +static const int da9063_bcores_merged_limits[] = { + 1000000, 1200000, 1400000, 1600000, 1800000, 2000000, 2200000, 2400000, + 2600000, 2800000, 3000000, 3200000, 3400000, 3600000, 3800000, 4000000 +}; + +/* Current limits array (in uA) for merged BMEM and BIO. + Entry indexes corresponds to register values. */ +static const int da9063_bmem_bio_merged_limits[] = { + 3000000, 3200000, 3400000, 3600000, 3800000, 4000000, 4200000, 4400000, + 4600000, 4800000, 5000000, 5200000, 5400000, 5600000, 5800000, 6000000 +}; + +static int da9063_set_current_limit(struct regulator_dev *rdev, + int min_uA, int max_uA) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + const struct da9063_regulator_info *rinfo = regl->info; + int n, tval; + + for (n = 0; n < rinfo->n_current_limits; n++) { + tval = rinfo->current_limits[n]; + if (tval >= min_uA && tval <= max_uA) + return regmap_field_write(regl->ilimit, n); + } + + return -EINVAL; +} + +static int da9063_get_current_limit(struct regulator_dev *rdev) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + const struct da9063_regulator_info *rinfo = regl->info; + unsigned int sel; + int ret; + + ret = regmap_field_read(regl->ilimit, &sel); + if (ret < 0) + return ret; + + if (sel >= rinfo->n_current_limits) + sel = rinfo->n_current_limits - 1; + + return rinfo->current_limits[sel]; +} + +static int da9063_buck_set_mode(struct regulator_dev *rdev, unsigned mode) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + unsigned val; + + switch (mode) { + case REGULATOR_MODE_FAST: + val = BUCK_MODE_SYNC; + break; + case REGULATOR_MODE_NORMAL: + val = BUCK_MODE_AUTO; + break; + case REGULATOR_MODE_STANDBY: + val = BUCK_MODE_SLEEP; + break; + default: + return -EINVAL; + } + + return regmap_field_write(regl->mode, val); +} + +/* + * Bucks use single mode register field for normal operation + * and suspend state. + * There are 3 modes to map to: FAST, NORMAL, and STANDBY. + */ + +static unsigned da9063_buck_get_mode(struct regulator_dev *rdev) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + struct regmap_field *field; + unsigned int val, mode = 0; + int ret; + + ret = regmap_field_read(regl->mode, &val); + if (ret < 0) + return ret; + + switch (val) { + default: + case BUCK_MODE_MANUAL: + mode = REGULATOR_MODE_FAST | REGULATOR_MODE_STANDBY; + /* Sleep flag bit decides the mode */ + break; + case BUCK_MODE_SLEEP: + return REGULATOR_MODE_STANDBY; + case BUCK_MODE_SYNC: + return REGULATOR_MODE_FAST; + case BUCK_MODE_AUTO: + return REGULATOR_MODE_NORMAL; + } + + /* Detect current regulator state */ + ret = regmap_field_read(regl->suspend, &val); + if (ret < 0) + return 0; + + /* Read regulator mode from proper register, depending on state */ + if (val) + field = regl->suspend_sleep; + else + field = regl->sleep; + + ret = regmap_field_read(field, &val); + if (ret < 0) + return 0; + + if (val) + mode &= REGULATOR_MODE_STANDBY; + else + mode &= REGULATOR_MODE_NORMAL | REGULATOR_MODE_FAST; + + return mode; +} + +/* + * LDOs use sleep flags - one for normal and one for suspend state. + * There are 2 modes to map to: NORMAL and STANDBY (sleep) for each state. + */ + +static int da9063_ldo_set_mode(struct regulator_dev *rdev, unsigned mode) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + unsigned val; + + switch (mode) { + case REGULATOR_MODE_NORMAL: + val = 0; + break; + case REGULATOR_MODE_STANDBY: + val = 1; + break; + default: + return -EINVAL; + } + + return regmap_field_write(regl->sleep, val); +} + +static unsigned da9063_ldo_get_mode(struct regulator_dev *rdev) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + struct regmap_field *field; + int ret, val; + + /* Detect current regulator state */ + ret = regmap_field_read(regl->suspend, &val); + if (ret < 0) + return 0; + + /* Read regulator mode from proper register, depending on state */ + if (val) + field = regl->suspend_sleep; + else + field = regl->sleep; + + ret = regmap_field_read(field, &val); + if (ret < 0) + return 0; + + if (val) + return REGULATOR_MODE_STANDBY; + else + return REGULATOR_MODE_NORMAL; +} + +static int da9063_buck_get_status(struct regulator_dev *rdev) +{ + int ret = regulator_is_enabled_regmap(rdev); + + if (ret == 0) { + ret = REGULATOR_STATUS_OFF; + } else if (ret > 0) { + ret = da9063_buck_get_mode(rdev); + if (ret > 0) + ret = regulator_mode_to_status(ret); + else if (ret == 0) + ret = -EIO; + } + + return ret; +} + +static int da9063_ldo_get_status(struct regulator_dev *rdev) +{ + int ret = regulator_is_enabled_regmap(rdev); + + if (ret == 0) { + ret = REGULATOR_STATUS_OFF; + } else if (ret > 0) { + ret = da9063_ldo_get_mode(rdev); + if (ret > 0) + ret = regulator_mode_to_status(ret); + else if (ret == 0) + ret = -EIO; + } + + return ret; +} + +static int da9063_set_suspend_voltage(struct regulator_dev *rdev, int uV) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + const struct da9063_regulator_info *rinfo = regl->info; + int ret, sel; + + sel = regulator_map_voltage_linear(rdev, uV, uV); + if (sel < 0) + return -EINVAL; + + sel <<= ffs(rdev->desc->vsel_mask) - 1; + + ret = regmap_update_bits(regl->hw->regmap, rinfo->suspend_vsel_reg, + rdev->desc->vsel_mask, sel); + + return ret; +} + +static int da9063_suspend_enable(struct regulator_dev *rdev) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + + return regmap_field_write(regl->suspend, 1); +} + +static int da9063_suspend_disable(struct regulator_dev *rdev) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + + return regmap_field_write(regl->suspend, 0); +} + +static int da9063_buck_set_suspend_mode(struct regulator_dev *rdev, unsigned mode) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + int val; + + switch (mode) { + case REGULATOR_MODE_FAST: + val = BUCK_MODE_SYNC; + break; + case REGULATOR_MODE_NORMAL: + val = BUCK_MODE_AUTO; + break; + case REGULATOR_MODE_STANDBY: + val = BUCK_MODE_SLEEP; + break; + default: + return -EINVAL; + } + + return regmap_field_write(regl->mode, val); +} + +static int da9063_ldo_set_suspend_mode(struct regulator_dev *rdev, unsigned mode) +{ + struct da9063_regulator *regl = rdev_get_drvdata(rdev); + unsigned val; + + switch (mode) { + case REGULATOR_MODE_NORMAL: + val = 0; + break; + case REGULATOR_MODE_STANDBY: + val = 1; + break; + default: + return -EINVAL; + } + + return regmap_field_write(regl->suspend_sleep, val); +} + +static struct regulator_ops da9063_buck_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .list_voltage = regulator_list_voltage_linear, + .set_current_limit = da9063_set_current_limit, + .get_current_limit = da9063_get_current_limit, + .set_mode = da9063_buck_set_mode, + .get_mode = da9063_buck_get_mode, + .get_status = da9063_buck_get_status, + .set_suspend_voltage = da9063_set_suspend_voltage, + .set_suspend_enable = da9063_suspend_enable, + .set_suspend_disable = da9063_suspend_disable, + .set_suspend_mode = da9063_buck_set_suspend_mode, +}; + +static struct regulator_ops da9063_ldo_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .list_voltage = regulator_list_voltage_linear, + .set_mode = da9063_ldo_set_mode, + .get_mode = da9063_ldo_get_mode, + .get_status = da9063_ldo_get_status, + .set_suspend_voltage = da9063_set_suspend_voltage, + .set_suspend_enable = da9063_suspend_enable, + .set_suspend_disable = da9063_suspend_disable, + .set_suspend_mode = da9063_ldo_set_suspend_mode, +}; + +/* Info of regulators for DA9063 */ +static const struct da9063_regulator_info da9063_regulator_info[] = { + { + DA9063_BUCK(DA9063, BCORE1, 300, 10, 1570, + da9063_buck_a_limits), + DA9063_BUCK_COMMON_FIELDS(BCORE1), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE1_SEL), + .ilimit = BFIELD(DA9063_REG_BUCK_ILIM_C, + DA9063_BCORE1_ILIM_MASK), + }, + { + DA9063_BUCK(DA9063, BCORE2, 300, 10, 1570, + da9063_buck_a_limits), + DA9063_BUCK_COMMON_FIELDS(BCORE2), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE2_SEL), + .ilimit = BFIELD(DA9063_REG_BUCK_ILIM_C, + DA9063_BCORE2_ILIM_MASK), + }, + { + DA9063_BUCK(DA9063, BPRO, 530, 10, 1800, + da9063_buck_a_limits), + DA9063_BUCK_COMMON_FIELDS(BPRO), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBPRO_SEL), + .ilimit = BFIELD(DA9063_REG_BUCK_ILIM_B, + DA9063_BPRO_ILIM_MASK), + }, + { + DA9063_BUCK(DA9063, BMEM, 800, 20, 3340, + da9063_buck_b_limits), + DA9063_BUCK_COMMON_FIELDS(BMEM), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBMEM_SEL), + .ilimit = BFIELD(DA9063_REG_BUCK_ILIM_A, + DA9063_BMEM_ILIM_MASK), + }, + { + DA9063_BUCK(DA9063, BIO, 800, 20, 3340, + da9063_buck_b_limits), + DA9063_BUCK_COMMON_FIELDS(BIO), + .suspend = BFIELD(DA9063_REG_DVC_2, DA9063_VBIO_SEL), + .ilimit = BFIELD(DA9063_REG_BUCK_ILIM_A, + DA9063_BIO_ILIM_MASK), + }, + { + DA9063_BUCK(DA9063, BPERI, 800, 20, 3340, + da9063_buck_b_limits), + DA9063_BUCK_COMMON_FIELDS(BPERI), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBPERI_SEL), + .ilimit = BFIELD(DA9063_REG_BUCK_ILIM_B, + DA9063_BPERI_ILIM_MASK), + }, + { + DA9063_BUCK(DA9063, BCORES_MERGED, 300, 10, 1570, + da9063_bcores_merged_limits), + /* BCORES_MERGED uses the same register fields as BCORE1 */ + DA9063_BUCK_COMMON_FIELDS(BCORE1), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE1_SEL), + .ilimit = BFIELD(DA9063_REG_BUCK_ILIM_C, + DA9063_BCORE1_ILIM_MASK), + }, + { + DA9063_BUCK(DA9063, BMEM_BIO_MERGED, 800, 20, 3340, + da9063_bmem_bio_merged_limits), + /* BMEM_BIO_MERGED uses the same register fields as BMEM */ + DA9063_BUCK_COMMON_FIELDS(BMEM), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBMEM_SEL), + .ilimit = BFIELD(DA9063_REG_BUCK_ILIM_A, + DA9063_BMEM_ILIM_MASK), + }, + { + DA9063_LDO(DA9063, LDO1, 600, 20, 1860), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO1_SEL), + }, + { + DA9063_LDO(DA9063, LDO2, 600, 20, 1860), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO2_SEL), + }, + { + DA9063_LDO(DA9063, LDO3, 900, 20, 3440), + .suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO3_SEL), + .oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO3_LIM), + }, + { + DA9063_LDO(DA9063, LDO4, 900, 20, 3440), + .suspend = BFIELD(DA9063_REG_DVC_2, DA9063_VLDO4_SEL), + .oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO4_LIM), + }, + { + DA9063_LDO(DA9063, LDO5, 900, 50, 3600), + .suspend = BFIELD(DA9063_REG_LDO5_CONT, DA9063_VLDO5_SEL), + }, + { + DA9063_LDO(DA9063, LDO6, 900, 50, 3600), + .suspend = BFIELD(DA9063_REG_LDO6_CONT, DA9063_VLDO6_SEL), + }, + { + DA9063_LDO(DA9063, LDO7, 900, 50, 3600), + .suspend = BFIELD(DA9063_REG_LDO7_CONT, DA9063_VLDO7_SEL), + .oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO7_LIM), + }, + { + DA9063_LDO(DA9063, LDO8, 900, 50, 3600), + .suspend = BFIELD(DA9063_REG_LDO8_CONT, DA9063_VLDO8_SEL), + .oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO8_LIM), + }, + { + DA9063_LDO(DA9063, LDO9, 950, 50, 3600), + .suspend = BFIELD(DA9063_REG_LDO9_CONT, DA9063_VLDO9_SEL), + }, + { + DA9063_LDO(DA9063, LDO10, 900, 50, 3600), + .suspend = BFIELD(DA9063_REG_LDO10_CONT, DA9063_VLDO10_SEL), + }, + { + DA9063_LDO(DA9063, LDO11, 900, 50, 3600), + .suspend = BFIELD(DA9063_REG_LDO11_CONT, DA9063_VLDO11_SEL), + .oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO11_LIM), + }, +}; + +/* Link chip model with regulators info table */ +static struct da9063_dev_model regulators_models[] = { + { + .regulator_info = da9063_regulator_info, + .n_regulators = ARRAY_SIZE(da9063_regulator_info), + .dev_model = PMIC_DA9063, + }, + { } +}; + +/* Regulator interrupt handlers */ +static irqreturn_t da9063_ldo_lim_event(int irq, void *data) +{ + struct da9063_regulators *regulators = data; + struct da9063 *hw = regulators->regulator[0].hw; + struct da9063_regulator *regl; + int bits, i , ret; + + ret = regmap_read(hw->regmap, DA9063_REG_STATUS_D, &bits); + if (ret < 0) + return IRQ_NONE; + + for (i = regulators->n_regulators - 1; i >= 0; i--) { + regl = ®ulators->regulator[i]; + if (regl->info->oc_event.reg != DA9063_REG_STATUS_D) + continue; + + if (BIT(regl->info->oc_event.lsb) & bits) + regulator_notifier_call_chain(regl->rdev, + REGULATOR_EVENT_OVER_CURRENT, NULL); + } + + return IRQ_HANDLED; +} + +/* + * Probing and Initialisation functions + */ +static const struct regulator_init_data *da9063_get_regulator_initdata( + const struct da9063_regulators_pdata *regl_pdata, int id) +{ + int i; + + for (i = 0; i < regl_pdata->n_regulators; i++) { + if (id == regl_pdata->regulator_data[i].id) + return regl_pdata->regulator_data[i].initdata; + } + + return NULL; +} + +#ifdef CONFIG_OF +static struct of_regulator_match da9063_matches[] = { + [DA9063_ID_BCORE1] = { .name = "bcore1" }, + [DA9063_ID_BCORE2] = { .name = "bcore2" }, + [DA9063_ID_BPRO] = { .name = "bpro", }, + [DA9063_ID_BMEM] = { .name = "bmem", }, + [DA9063_ID_BIO] = { .name = "bio", }, + [DA9063_ID_BPERI] = { .name = "bperi", }, + [DA9063_ID_BCORES_MERGED] = { .name = "bcores-merged" }, + [DA9063_ID_BMEM_BIO_MERGED] = { .name = "bmem-bio-merged", }, + [DA9063_ID_LDO1] = { .name = "ldo1", }, + [DA9063_ID_LDO2] = { .name = "ldo2", }, + [DA9063_ID_LDO3] = { .name = "ldo3", }, + [DA9063_ID_LDO4] = { .name = "ldo4", }, + [DA9063_ID_LDO5] = { .name = "ldo5", }, + [DA9063_ID_LDO6] = { .name = "ldo6", }, + [DA9063_ID_LDO7] = { .name = "ldo7", }, + [DA9063_ID_LDO8] = { .name = "ldo8", }, + [DA9063_ID_LDO9] = { .name = "ldo9", }, + [DA9063_ID_LDO10] = { .name = "ldo10", }, + [DA9063_ID_LDO11] = { .name = "ldo11", }, +}; + +static struct da9063_regulators_pdata *da9063_parse_regulators_dt( + struct platform_device *pdev, + struct of_regulator_match **da9063_reg_matches) +{ + struct da9063_regulators_pdata *pdata; + struct da9063_regulator_data *rdata; + struct device_node *node; + int i, n, num; + + node = of_find_node_by_name(pdev->dev.parent->of_node, "regulators"); + if (!node) { + dev_err(&pdev->dev, "Regulators device node not found\n"); + return ERR_PTR(-ENODEV); + } + + num = of_regulator_match(&pdev->dev, node, da9063_matches, + ARRAY_SIZE(da9063_matches)); + if (num < 0) { + dev_err(&pdev->dev, "Failed to match regulators\n"); + return ERR_PTR(-EINVAL); + } + + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return ERR_PTR(-ENOMEM); + + pdata->regulator_data = devm_kzalloc(&pdev->dev, + num * sizeof(*pdata->regulator_data), + GFP_KERNEL); + if (!pdata->regulator_data) + return ERR_PTR(-ENOMEM); + pdata->n_regulators = num; + + n = 0; + for (i = 0; i < ARRAY_SIZE(da9063_matches); i++) { + if (!da9063_matches[i].init_data) + continue; + + rdata = &pdata->regulator_data[n]; + rdata->id = i; + rdata->initdata = da9063_matches[i].init_data; + + n++; + }; + + *da9063_reg_matches = da9063_matches; + return pdata; +} +#else +static struct da9063_regulators_pdata *da9063_parse_regulators_dt( + struct platform_device *pdev, + struct of_regulator_match **da9063_reg_matches) +{ + da9063_reg_matches = NULL; + return PTR_ERR(-ENODEV); +} +#endif + +static int da9063_regulator_probe(struct platform_device *pdev) +{ + struct da9063 *da9063 = dev_get_drvdata(pdev->dev.parent); + struct da9063_pdata *da9063_pdata = dev_get_platdata(da9063->dev); + struct of_regulator_match *da9063_reg_matches; + struct da9063_regulators_pdata *regl_pdata; + const struct da9063_dev_model *model; + struct da9063_regulators *regulators; + struct da9063_regulator *regl; + struct regulator_config config; + bool bcores_merged, bmem_bio_merged; + int id, irq, n, n_regulators, ret, val; + size_t size; + + regl_pdata = da9063_pdata ? da9063_pdata->regulators_pdata : NULL; + + if (!regl_pdata) + regl_pdata = da9063_parse_regulators_dt(pdev, + &da9063_reg_matches); + + if (IS_ERR(regl_pdata) || regl_pdata->n_regulators == 0) { + dev_err(&pdev->dev, + "No regulators defined for the platform\n"); + return PTR_ERR(regl_pdata); + } + + /* Find regulators set for particular device model */ + for (model = regulators_models; model->regulator_info; model++) { + if (model->dev_model == da9063->model) + break; + } + if (!model->regulator_info) { + dev_err(&pdev->dev, "Chip model not recognised (%u)\n", + da9063->model); + return -ENODEV; + } + + ret = regmap_read(da9063->regmap, DA9063_REG_CONFIG_H, &val); + if (ret < 0) { + dev_err(&pdev->dev, + "Error while reading BUCKs configuration\n"); + return -EIO; + } + bcores_merged = val & DA9063_BCORE_MERGE; + bmem_bio_merged = val & DA9063_BUCK_MERGE; + + n_regulators = model->n_regulators; + if (bcores_merged) + n_regulators -= 2; /* remove BCORE1, BCORE2 */ + else + n_regulators--; /* remove BCORES_MERGED */ + if (bmem_bio_merged) + n_regulators -= 2; /* remove BMEM, BIO */ + else + n_regulators--; /* remove BMEM_BIO_MERGED */ + + /* Allocate memory required by usable regulators */ + size = sizeof(struct da9063_regulators) + + n_regulators * sizeof(struct da9063_regulator); + regulators = devm_kzalloc(&pdev->dev, size, GFP_KERNEL); + if (!regulators) { + dev_err(&pdev->dev, "No memory for regulators\n"); + return -ENOMEM; + } + + regulators->n_regulators = n_regulators; + platform_set_drvdata(pdev, regulators); + + /* Register all regulators declared in platform information */ + n = 0; + id = 0; + while (n < regulators->n_regulators) { + /* Skip regulator IDs depending on merge mode configuration */ + switch (id) { + case DA9063_ID_BCORE1: + case DA9063_ID_BCORE2: + if (bcores_merged) { + id++; + continue; + } + break; + case DA9063_ID_BMEM: + case DA9063_ID_BIO: + if (bmem_bio_merged) { + id++; + continue; + } + break; + case DA9063_ID_BCORES_MERGED: + if (!bcores_merged) { + id++; + continue; + } + break; + case DA9063_ID_BMEM_BIO_MERGED: + if (!bmem_bio_merged) { + id++; + continue; + } + break; + } + + /* Initialise regulator structure */ + regl = ®ulators->regulator[n]; + regl->hw = da9063; + regl->info = &model->regulator_info[id]; + regl->desc = regl->info->desc; + regl->desc.type = REGULATOR_VOLTAGE; + regl->desc.owner = THIS_MODULE; + + if (regl->info->mode.reg) + regl->mode = devm_regmap_field_alloc(&pdev->dev, + da9063->regmap, regl->info->mode); + if (regl->info->suspend.reg) + regl->suspend = devm_regmap_field_alloc(&pdev->dev, + da9063->regmap, regl->info->suspend); + if (regl->info->sleep.reg) + regl->sleep = devm_regmap_field_alloc(&pdev->dev, + da9063->regmap, regl->info->sleep); + if (regl->info->suspend_sleep.reg) + regl->suspend_sleep = devm_regmap_field_alloc(&pdev->dev, + da9063->regmap, regl->info->suspend_sleep); + if (regl->info->ilimit.reg) + regl->ilimit = devm_regmap_field_alloc(&pdev->dev, + da9063->regmap, regl->info->ilimit); + + /* Register regulator */ + memset(&config, 0, sizeof(config)); + config.dev = &pdev->dev; + config.init_data = da9063_get_regulator_initdata(regl_pdata, id); + config.driver_data = regl; + if (da9063_reg_matches) + config.of_node = da9063_reg_matches[id].of_node; + config.regmap = da9063->regmap; + regl->rdev = regulator_register(®l->desc, &config); + if (IS_ERR(regl->rdev)) { + dev_err(&pdev->dev, + "Failed to register %s regulator\n", + regl->desc.name); + ret = PTR_ERR(regl->rdev); + goto err; + } + id++; + n++; + } + + /* LDOs overcurrent event support */ + irq = platform_get_irq_byname(pdev, "LDO_LIM"); + if (irq < 0) { + ret = irq; + dev_err(&pdev->dev, "Failed to get IRQ.\n"); + goto err; + } + + regulators->irq_ldo_lim = regmap_irq_get_virq(da9063->regmap_irq, irq); + if (regulators->irq_ldo_lim >= 0) { + ret = request_threaded_irq(regulators->irq_ldo_lim, + NULL, da9063_ldo_lim_event, + IRQF_TRIGGER_LOW | IRQF_ONESHOT, + "LDO_LIM", regulators); + if (ret) { + dev_err(&pdev->dev, + "Failed to request LDO_LIM IRQ.\n"); + regulators->irq_ldo_lim = -ENXIO; + } + } + + return 0; + +err: + /* Wind back regulators registeration */ + while (--n >= 0) + regulator_unregister(regulators->regulator[n].rdev); + + return ret; +} + +static int da9063_regulator_remove(struct platform_device *pdev) +{ + struct da9063_regulators *regulators = platform_get_drvdata(pdev); + struct da9063_regulator *regl; + + free_irq(regulators->irq_ldo_lim, regulators); + free_irq(regulators->irq_uvov, regulators); + + for (regl = ®ulators->regulator[regulators->n_regulators - 1]; + regl >= ®ulators->regulator[0]; regl--) + regulator_unregister(regl->rdev); + + return 0; +} + +static struct platform_driver da9063_regulator_driver = { + .driver = { + .name = DA9063_DRVNAME_REGULATORS, + .owner = THIS_MODULE, + }, + .probe = da9063_regulator_probe, + .remove = da9063_regulator_remove, +}; + +static int __init da9063_regulator_init(void) +{ + return platform_driver_register(&da9063_regulator_driver); +} +subsys_initcall(da9063_regulator_init); + +static void __exit da9063_regulator_cleanup(void) +{ + platform_driver_unregister(&da9063_regulator_driver); +} +module_exit(da9063_regulator_cleanup); + + +/* Module information */ +MODULE_AUTHOR("Krystian Garbaciak "); +MODULE_DESCRIPTION("DA9063 regulators driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("paltform:" DA9063_DRVNAME_REGULATORS); diff --git a/drivers/regulator/da9210-regulator.c b/drivers/regulator/da9210-regulator.c new file mode 100644 index 000000000000..f0fe54b38977 --- /dev/null +++ b/drivers/regulator/da9210-regulator.c @@ -0,0 +1,196 @@ +/* + * da9210-regulator.c - Regulator device driver for DA9210 + * Copyright (C) 2013 Dialog Semiconductor Ltd. + * + * This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU Library General Public + * License as published by the Free Software Foundation; either + * version 2 of the License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * Library General Public License for more details. + * + * You should have received a copy of the GNU Library General Public + * License along with this library; if not, write to the + * Free Software Foundation, Inc., 51 Franklin St, Fifth Floor, + * Boston, MA 02110-1301, USA. + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#include "da9210-regulator.h" + +struct da9210 { + struct regulator_dev *rdev; + struct regmap *regmap; +}; + +static const struct regmap_config da9210_regmap_config = { + .reg_bits = 8, + .val_bits = 8, +}; + +static int da9210_set_current_limit(struct regulator_dev *rdev, int min_uA, + int max_uA); +static int da9210_get_current_limit(struct regulator_dev *rdev); + +static struct regulator_ops da9210_buck_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .list_voltage = regulator_list_voltage_linear, + .set_current_limit = da9210_set_current_limit, + .get_current_limit = da9210_get_current_limit, +}; + +/* Default limits measured in millivolts and milliamps */ +#define DA9210_MIN_MV 300 +#define DA9210_MAX_MV 1570 +#define DA9210_STEP_MV 10 + +/* Current limits for buck (uA) indices corresponds with register values */ +static const int da9210_buck_limits[] = { + 1600000, 1800000, 2000000, 2200000, 2400000, 2600000, 2800000, 3000000, + 3200000, 3400000, 3600000, 3800000, 4000000, 4200000, 4400000, 4600000 +}; + +static const struct regulator_desc da9210_reg = { + .name = "DA9210", + .id = 0, + .ops = &da9210_buck_ops, + .type = REGULATOR_VOLTAGE, + .n_voltages = ((DA9210_MAX_MV - DA9210_MIN_MV) / DA9210_STEP_MV) + 1, + .min_uV = (DA9210_MIN_MV * 1000), + .uV_step = (DA9210_STEP_MV * 1000), + .vsel_reg = DA9210_REG_VBUCK_A, + .vsel_mask = DA9210_VBUCK_MASK, + .enable_reg = DA9210_REG_BUCK_CONT, + .enable_mask = DA9210_BUCK_EN, + .owner = THIS_MODULE, +}; + +static int da9210_set_current_limit(struct regulator_dev *rdev, int min_uA, + int max_uA) +{ + struct da9210 *chip = rdev_get_drvdata(rdev); + unsigned int sel; + int i; + + /* search for closest to maximum */ + for (i = ARRAY_SIZE(da9210_buck_limits)-1; i >= 0; i--) { + if (min_uA <= da9210_buck_limits[i] && + max_uA >= da9210_buck_limits[i]) { + sel = i; + sel = sel << DA9210_BUCK_ILIM_SHIFT; + return regmap_update_bits(chip->regmap, + DA9210_REG_BUCK_ILIM, + DA9210_BUCK_ILIM_MASK, sel); + } + } + + return -EINVAL; +} + +static int da9210_get_current_limit(struct regulator_dev *rdev) +{ + struct da9210 *chip = rdev_get_drvdata(rdev); + unsigned int data; + unsigned int sel; + int ret; + + ret = regmap_read(chip->regmap, DA9210_REG_BUCK_ILIM, &data); + if (ret < 0) + return ret; + + /* select one of 16 values: 0000 (1600mA) to 1111 (4600mA) */ + sel = (data & DA9210_BUCK_ILIM_MASK) >> DA9210_BUCK_ILIM_SHIFT; + + return da9210_buck_limits[sel]; +} + +/* + * I2C driver interface functions + */ +static int da9210_i2c_probe(struct i2c_client *i2c, + const struct i2c_device_id *id) +{ + struct da9210 *chip; + struct da9210_pdata *pdata = i2c->dev.platform_data; + struct regulator_dev *rdev = NULL; + struct regulator_config config = { }; + int error; + + chip = devm_kzalloc(&i2c->dev, sizeof(struct da9210), GFP_KERNEL); + if (NULL == chip) { + dev_err(&i2c->dev, + "Cannot kzalloc memory for regulator structure\n"); + return -ENOMEM; + } + + chip->regmap = devm_regmap_init_i2c(i2c, &da9210_regmap_config); + if (IS_ERR(chip->regmap)) { + error = PTR_ERR(chip->regmap); + dev_err(&i2c->dev, "Failed to allocate register map: %d\n", + error); + return error; + } + + config.dev = &i2c->dev; + if (pdata) + config.init_data = &pdata->da9210_constraints; + config.driver_data = chip; + config.regmap = chip->regmap; + + rdev = regulator_register(&da9210_reg, &config); + if (IS_ERR(rdev)) { + dev_err(&i2c->dev, "Failed to register DA9210 regulator\n"); + return PTR_ERR(rdev); + } + + chip->rdev = rdev; + + i2c_set_clientdata(i2c, chip); + + return 0; +} + +static int da9210_i2c_remove(struct i2c_client *i2c) +{ + struct da9210 *chip = i2c_get_clientdata(i2c); + regulator_unregister(chip->rdev); + return 0; +} + +static const struct i2c_device_id da9210_i2c_id[] = { + {"da9210", 0}, + {}, +}; + +MODULE_DEVICE_TABLE(i2c, da9210_i2c_id); + +static struct i2c_driver da9210_regulator_driver = { + .driver = { + .name = "da9210", + .owner = THIS_MODULE, + }, + .probe = da9210_i2c_probe, + .remove = da9210_i2c_remove, + .id_table = da9210_i2c_id, +}; + +module_i2c_driver(da9210_regulator_driver); + +MODULE_AUTHOR("S Twiss "); +MODULE_DESCRIPTION("Regulator device driver for Dialog DA9210"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/regulator/da9210-regulator.h b/drivers/regulator/da9210-regulator.h new file mode 100644 index 000000000000..749c550808b6 --- /dev/null +++ b/drivers/regulator/da9210-regulator.h @@ -0,0 +1,288 @@ + +/* + * da9210-regulator.h - Regulator definitions for DA9210 + * Copyright (C) 2013 Dialog Semiconductor Ltd. + * + * This library is free software; you can redistribute it and/or + * modify it under the terms of the GNU Library General Public + * License as published by the Free Software Foundation; either + * version 2 of the License, or (at your option) any later version. + * + * This library is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * Library General Public License for more details. + * + * You should have received a copy of the GNU Library General Public + * License along with this library; if not, write to the + * Free Software Foundation, Inc., 51 Franklin St, Fifth Floor, + * Boston, MA 02110-1301, USA. + */ + +#ifndef __DA9210_REGISTERS_H__ +#define __DA9210_REGISTERS_H__ + +struct da9210_pdata { + struct regulator_init_data da9210_constraints; +}; + +/* Page selection */ +#define DA9210_REG_PAGE_CON 0x00 + +/* System Control and Event Registers */ +#define DA9210_REG_STATUS_A 0x50 +#define DA9210_REG_STATUS_B 0x51 +#define DA9210_REG_EVENT_A 0x52 +#define DA9210_REG_EVENT_B 0x53 +#define DA9210_REG_MASK_A 0x54 +#define DA9210_REG_MASK_B 0x55 +#define DA9210_REG_CONTROL_A 0x56 + +/* GPIO Control Registers */ +#define DA9210_REG_GPIO_0_1 0x58 +#define DA9210_REG_GPIO_2_3 0x59 +#define DA9210_REG_GPIO_4_5 0x5A +#define DA9210_REG_GPIO_6 0x5B + +/* Regulator Registers */ +#define DA9210_REG_BUCK_CONT 0x5D +#define DA9210_REG_BUCK_ILIM 0xD0 +#define DA9210_REG_BUCK_CONF1 0xD1 +#define DA9210_REG_BUCK_CONF2 0xD2 +#define DA9210_REG_VBACK_AUTO 0xD4 +#define DA9210_REG_VBACK_BASE 0xD5 +#define DA9210_REG_VBACK_MAX_DVC_IF 0xD6 +#define DA9210_REG_VBACK_DVC 0xD7 +#define DA9210_REG_VBUCK_A 0xD8 +#define DA9210_REG_VBUCK_B 0xD9 + +/* I2C Interface Settings */ +#define DA9210_REG_INTERFACE 0x105 + +/* OTP */ +#define DA9210_REG_OPT_COUNT 0x140 +#define DA9210_REG_OPT_ADDR 0x141 +#define DA9210_REG_OPT_DATA 0x142 + +/* Customer Trim and Configuration */ +#define DA9210_REG_CONFIG_A 0x143 +#define DA9210_REG_CONFIG_B 0x144 +#define DA9210_REG_CONFIG_C 0x145 +#define DA9210_REG_CONFIG_D 0x146 +#define DA9210_REG_CONFIG_E 0x147 + + +/* + * Registers bits + */ +/* DA9210_REG_PAGE_CON (addr=0x00) */ +#define DA9210_PEG_PAGE_SHIFT 0 +#define DA9210_REG_PAGE_MASK 0x0F +/* On I2C registers 0x00 - 0xFF */ +#define DA9210_REG_PAGE0 0 +/* On I2C registers 0x100 - 0x1FF */ +#define DA9210_REG_PAGE2 2 +#define DA9210_PAGE_WRITE_MODE 0x00 +#define DA9210_REPEAT_WRITE_MODE 0x40 +#define DA9210_PAGE_REVERT 0x80 + +/* DA9210_REG_STATUS_A (addr=0x50) */ +#define DA9210_GPI0 0x01 +#define DA9210_GPI1 0x02 +#define DA9210_GPI2 0x04 +#define DA9210_GPI3 0x08 +#define DA9210_GPI4 0x10 +#define DA9210_GPI5 0x20 +#define DA9210_GPI6 0x40 + +/* DA9210_REG_EVENT_A (addr=0x52) */ +#define DA9210_E_GPI0 0x01 +#define DA9210_E_GPI1 0x02 +#define DA9210_E_GPI2 0x04 +#define DA9210_E_GPI3 0x08 +#define DA9210_E_GPI4 0x10 +#define DA9210_E_GPI5 0x20 +#define DA9210_E_GPI6 0x40 + +/* DA9210_REG_EVENT_B (addr=0x53) */ +#define DA9210_E_OVCURR 0x01 +#define DA9210_E_NPWRGOOD 0x02 +#define DA9210_E_TEMP_WARN 0x04 +#define DA9210_E_TEMP_CRIT 0x08 +#define DA9210_E_VMAX 0x10 + +/* DA9210_REG_MASK_A (addr=0x54) */ +#define DA9210_M_GPI0 0x01 +#define DA9210_M_GPI1 0x02 +#define DA9210_M_GPI2 0x04 +#define DA9210_M_GPI3 0x08 +#define DA9210_M_GPI4 0x10 +#define DA9210_M_GPI5 0x20 +#define DA9210_M_GPI6 0x40 + +/* DA9210_REG_MASK_B (addr=0x55) */ +#define DA9210_M_OVCURR 0x01 +#define DA9210_M_NPWRGOOD 0x02 +#define DA9210_M_TEMP_WARN 0x04 +#define DA9210_M_TEMP_CRIT 0x08 +#define DA9210_M_VMAX 0x10 + +/* DA9210_REG_CONTROL_A (addr=0x56) */ +#define DA9210_DEBOUNCING_SHIFT 0 +#define DA9210_DEBOUNCING_MASK 0x07 +#define DA9210_SLEW_RATE_SHIFT 3 +#define DA9210_SLEW_RATE_MASK 0x18 +#define DA9210_V_LOCK 0x20 + +/* DA9210_REG_GPIO_0_1 (addr=0x58) */ +#define DA9210_GPIO0_PIN_SHIFT 0 +#define DA9210_GPIO0_PIN_MASK 0x03 +#define DA9210_GPIO0_PIN_GPI 0x00 +#define DA9210_GPIO0_PIN_GPO_OD 0x02 +#define DA9210_GPIO0_PIN_GPO 0x03 +#define DA9210_GPIO0_TYPE 0x04 +#define DA9210_GPIO0_TYPE_GPI 0x00 +#define DA9210_GPIO0_TYPE_GPO 0x04 +#define DA9210_GPIO0_MODE 0x08 +#define DA9210_GPIO1_PIN_SHIFT 4 +#define DA9210_GPIO1_PIN_MASK 0x30 +#define DA9210_GPIO1_PIN_GPI 0x00 +#define DA9210_GPIO1_PIN_VERROR 0x10 +#define DA9210_GPIO1_PIN_GPO_OD 0x20 +#define DA9210_GPIO1_PIN_GPO 0x30 +#define DA9210_GPIO1_TYPE_SHIFT 0x40 +#define DA9210_GPIO1_TYPE_GPI 0x00 +#define DA9210_GPIO1_TYPE_GPO 0x40 +#define DA9210_GPIO1_MODE 0x80 + +/* DA9210_REG_GPIO_2_3 (addr=0x59) */ +#define DA9210_GPIO2_PIN_SHIFT 0 +#define DA9210_GPIO2_PIN_MASK 0x03 +#define DA9210_GPIO2_PIN_GPI 0x00 +#define DA9210_GPIO5_PIN_BUCK_CLK 0x10 +#define DA9210_GPIO2_PIN_GPO_OD 0x02 +#define DA9210_GPIO2_PIN_GPO 0x03 +#define DA9210_GPIO2_TYPE 0x04 +#define DA9210_GPIO2_TYPE_GPI 0x00 +#define DA9210_GPIO2_TYPE_GPO 0x04 +#define DA9210_GPIO2_MODE 0x08 +#define DA9210_GPIO3_PIN_SHIFT 4 +#define DA9210_GPIO3_PIN_MASK 0x30 +#define DA9210_GPIO3_PIN_GPI 0x00 +#define DA9210_GPIO3_PIN_IERROR 0x10 +#define DA9210_GPIO3_PIN_GPO_OD 0x20 +#define DA9210_GPIO3_PIN_GPO 0x30 +#define DA9210_GPIO3_TYPE_SHIFT 0x40 +#define DA9210_GPIO3_TYPE_GPI 0x00 +#define DA9210_GPIO3_TYPE_GPO 0x40 +#define DA9210_GPIO3_MODE 0x80 + +/* DA9210_REG_GPIO_4_5 (addr=0x5A) */ +#define DA9210_GPIO4_PIN_SHIFT 0 +#define DA9210_GPIO4_PIN_MASK 0x03 +#define DA9210_GPIO4_PIN_GPI 0x00 +#define DA9210_GPIO4_PIN_GPO_OD 0x02 +#define DA9210_GPIO4_PIN_GPO 0x03 +#define DA9210_GPIO4_TYPE 0x04 +#define DA9210_GPIO4_TYPE_GPI 0x00 +#define DA9210_GPIO4_TYPE_GPO 0x04 +#define DA9210_GPIO4_MODE 0x08 +#define DA9210_GPIO5_PIN_SHIFT 4 +#define DA9210_GPIO5_PIN_MASK 0x30 +#define DA9210_GPIO5_PIN_GPI 0x00 +#define DA9210_GPIO5_PIN_INTERFACE 0x01 +#define DA9210_GPIO5_PIN_GPO_OD 0x20 +#define DA9210_GPIO5_PIN_GPO 0x30 +#define DA9210_GPIO5_TYPE_SHIFT 0x40 +#define DA9210_GPIO5_TYPE_GPI 0x00 +#define DA9210_GPIO5_TYPE_GPO 0x40 +#define DA9210_GPIO5_MODE 0x80 + +/* DA9210_REG_GPIO_6 (addr=0x5B) */ +#define DA9210_GPIO6_PIN_SHIFT 0 +#define DA9210_GPIO6_PIN_MASK 0x03 +#define DA9210_GPIO6_PIN_GPI 0x00 +#define DA9210_GPIO6_PIN_INTERFACE 0x01 +#define DA9210_GPIO6_PIN_GPO_OD 0x02 +#define DA9210_GPIO6_PIN_GPO 0x03 +#define DA9210_GPIO6_TYPE 0x04 +#define DA9210_GPIO6_TYPE_GPI 0x00 +#define DA9210_GPIO6_TYPE_GPO 0x04 +#define DA9210_GPIO6_MODE 0x08 + +/* DA9210_REG_BUCK_CONT (addr=0x5D) */ +#define DA9210_BUCK_EN 0x01 +#define DA9210_BUCK_GPI_SHIFT 1 +#define DA9210_BUCK_GPI_MASK 0x06 +#define DA9210_BUCK_GPI_OFF 0x00 +#define DA9210_BUCK_GPI_GPIO0 0x02 +#define DA9210_BUCK_GPI_GPIO3 0x04 +#define DA9210_BUCK_GPI_GPIO4 0x06 +#define DA9210_BUCK_PD_DIS 0x08 +#define DA9210_VBUCK_SEL 0x10 +#define DA9210_VBUCK_SEL_A 0x00 +#define DA9210_VBUCK_SEL_B 0x10 +#define DA9210_VBUCK_GPI_SHIFT 5 +#define DA9210_VBUCK_GPI_MASK 0x60 +#define DA9210_VBUCK_GPI_OFF 0x00 +#define DA9210_VBUCK_GPI_GPIO0 0x20 +#define DA9210_VBUCK_GPI_GPIO3 0x40 +#define DA9210_VBUCK_GPI_GPIO4 0x60 +#define DA9210_DVC_CTRL_EN 0x80 + +/* DA9210_REG_BUCK_ILIM (addr=0xD0) */ +#define DA9210_BUCK_ILIM_SHIFT 0 +#define DA9210_BUCK_ILIM_MASK 0x0F +#define DA9210_BUCK_IALARM 0x10 + +/* DA9210_REG_BUCK_CONF1 (addr=0xD1) */ +#define DA9210_BUCK_MODE_SHIFT 0 +#define DA9210_BUCK_MODE_MASK 0x03 +#define DA9210_BUCK_MODE_MANUAL 0x00 +#define DA9210_BUCK_MODE_SLEEP 0x01 +#define DA9210_BUCK_MODE_SYNC 0x02 +#define DA9210_BUCK_MODE_AUTO 0x03 +#define DA9210_STARTUP_CTRL_SHIFT 2 +#define DA9210_STARTUP_CTRL_MASK 0x1C +#define DA9210_PWR_DOWN_CTRL_SHIFT 5 +#define DA9210_PWR_DOWN_CTRL_MASK 0xE0 + +/* DA9210_REG_BUCK_CONF2 (addr=0xD2) */ +#define DA9210_PHASE_SEL_SHIFT 0 +#define DA9210_PHASE_SEL_MASK 0x03 +#define DA9210_FREQ_SEL 0x40 + +/* DA9210_REG_BUCK_AUTO (addr=0xD4) */ +#define DA9210_VBUCK_AUTO_SHIFT 0 +#define DA9210_VBUCK_AUTO_MASK 0x7F + +/* DA9210_REG_BUCK_BASE (addr=0xD5) */ +#define DA9210_VBUCK_BASE_SHIFT 0 +#define DA9210_VBUCK_BASE_MASK 0x7F + +/* DA9210_REG_VBUCK_MAX_DVC_IF (addr=0xD6) */ +#define DA9210_VBUCK_MAX_SHIFT 0 +#define DA9210_VBUCK_MAX_MASK 0x7F +#define DA9210_DVC_STEP_SIZE 0x80 +#define DA9210_DVC_STEP_SIZE_10MV 0x00 +#define DA9210_DVC_STEP_SIZE_20MV 0x80 + +/* DA9210_REG_VBUCK_DVC (addr=0xD7) */ +#define DA9210_VBUCK_DVC_SHIFT 0 +#define DA9210_VBUCK_DVC_MASK 0x7F + +/* DA9210_REG_VBUCK_A/B (addr=0xD8/0xD9) */ +#define DA9210_VBUCK_SHIFT 0 +#define DA9210_VBUCK_MASK 0x7F +#define DA9210_VBUCK_BIAS 0 +#define DA9210_BUCK_SL 0x80 + +/* DA9210_REG_INTERFACE (addr=0x105) */ +#define DA9210_IF_BASE_ADDR_SHIFT 4 +#define DA9210_IF_BASE_ADDR_MASK 0xF0 + +/* DA9210_REG_CONFIG_E (addr=0x147) */ +#define DA9210_STAND_ALONE 0x01 + +#endif /* __DA9210_REGISTERS_H__ */ + diff --git a/drivers/regulator/fan53555.c b/drivers/regulator/fan53555.c index f0e1ae52bb05..a32b44272a05 100644 --- a/drivers/regulator/fan53555.c +++ b/drivers/regulator/fan53555.c @@ -237,7 +237,7 @@ static int fan53555_regulator_probe(struct i2c_client *client, unsigned int val; int ret; - pdata = client->dev.platform_data; + pdata = dev_get_platdata(&client->dev); if (!pdata || !pdata->regulator) { dev_err(&client->dev, "Platform data not found!\n"); return -ENODEV; diff --git a/drivers/regulator/fixed.c b/drivers/regulator/fixed.c index e5c03b534fae..7610920014d7 100644 --- a/drivers/regulator/fixed.c +++ b/drivers/regulator/fixed.c @@ -146,7 +146,7 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev) if (IS_ERR(config)) return PTR_ERR(config); } else { - config = pdev->dev.platform_data; + config = dev_get_platdata(&pdev->dev); } if (!config) diff --git a/drivers/regulator/gpio-regulator.c b/drivers/regulator/gpio-regulator.c index 9d39eb4aafa3..98a98ffa7fe0 100644 --- a/drivers/regulator/gpio-regulator.c +++ b/drivers/regulator/gpio-regulator.c @@ -219,7 +219,7 @@ static struct regulator_ops gpio_regulator_current_ops = { static int gpio_regulator_probe(struct platform_device *pdev) { - struct gpio_regulator_config *config = pdev->dev.platform_data; + struct gpio_regulator_config *config = dev_get_platdata(&pdev->dev); struct device_node *np = pdev->dev.of_node; struct gpio_regulator_data *drvdata; struct regulator_config cfg = { }; diff --git a/drivers/regulator/helpers.c b/drivers/regulator/helpers.c new file mode 100644 index 000000000000..6e30df14714b --- /dev/null +++ b/drivers/regulator/helpers.c @@ -0,0 +1,447 @@ +/* + * helpers.c -- Voltage/Current Regulator framework helper functions. + * + * Copyright 2007, 2008 Wolfson Microelectronics PLC. + * Copyright 2008 SlimLogic Ltd. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ + +#include +#include +#include +#include +#include +#include +#include + +/** + * regulator_is_enabled_regmap - standard is_enabled() for regmap users + * + * @rdev: regulator to operate on + * + * Regulators that use regmap for their register I/O can set the + * enable_reg and enable_mask fields in their descriptor and then use + * this as their is_enabled operation, saving some code. + */ +int regulator_is_enabled_regmap(struct regulator_dev *rdev) +{ + unsigned int val; + int ret; + + ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val); + if (ret != 0) + return ret; + + if (rdev->desc->enable_is_inverted) + return (val & rdev->desc->enable_mask) == 0; + else + return (val & rdev->desc->enable_mask) != 0; +} +EXPORT_SYMBOL_GPL(regulator_is_enabled_regmap); + +/** + * regulator_enable_regmap - standard enable() for regmap users + * + * @rdev: regulator to operate on + * + * Regulators that use regmap for their register I/O can set the + * enable_reg and enable_mask fields in their descriptor and then use + * this as their enable() operation, saving some code. + */ +int regulator_enable_regmap(struct regulator_dev *rdev) +{ + unsigned int val; + + if (rdev->desc->enable_is_inverted) + val = 0; + else + val = rdev->desc->enable_mask; + + return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + rdev->desc->enable_mask, val); +} +EXPORT_SYMBOL_GPL(regulator_enable_regmap); + +/** + * regulator_disable_regmap - standard disable() for regmap users + * + * @rdev: regulator to operate on + * + * Regulators that use regmap for their register I/O can set the + * enable_reg and enable_mask fields in their descriptor and then use + * this as their disable() operation, saving some code. + */ +int regulator_disable_regmap(struct regulator_dev *rdev) +{ + unsigned int val; + + if (rdev->desc->enable_is_inverted) + val = rdev->desc->enable_mask; + else + val = 0; + + return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg, + rdev->desc->enable_mask, val); +} +EXPORT_SYMBOL_GPL(regulator_disable_regmap); + +/** + * regulator_get_voltage_sel_regmap - standard get_voltage_sel for regmap users + * + * @rdev: regulator to operate on + * + * Regulators that use regmap for their register I/O can set the + * vsel_reg and vsel_mask fields in their descriptor and then use this + * as their get_voltage_vsel operation, saving some code. + */ +int regulator_get_voltage_sel_regmap(struct regulator_dev *rdev) +{ + unsigned int val; + int ret; + + ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val); + if (ret != 0) + return ret; + + val &= rdev->desc->vsel_mask; + val >>= ffs(rdev->desc->vsel_mask) - 1; + + return val; +} +EXPORT_SYMBOL_GPL(regulator_get_voltage_sel_regmap); + +/** + * regulator_set_voltage_sel_regmap - standard set_voltage_sel for regmap users + * + * @rdev: regulator to operate on + * @sel: Selector to set + * + * Regulators that use regmap for their register I/O can set the + * vsel_reg and vsel_mask fields in their descriptor and then use this + * as their set_voltage_vsel operation, saving some code. + */ +int regulator_set_voltage_sel_regmap(struct regulator_dev *rdev, unsigned sel) +{ + int ret; + + sel <<= ffs(rdev->desc->vsel_mask) - 1; + + ret = regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg, + rdev->desc->vsel_mask, sel); + if (ret) + return ret; + + if (rdev->desc->apply_bit) + ret = regmap_update_bits(rdev->regmap, rdev->desc->apply_reg, + rdev->desc->apply_bit, + rdev->desc->apply_bit); + return ret; +} +EXPORT_SYMBOL_GPL(regulator_set_voltage_sel_regmap); + +/** + * regulator_map_voltage_iterate - map_voltage() based on list_voltage() + * + * @rdev: Regulator to operate on + * @min_uV: Lower bound for voltage + * @max_uV: Upper bound for voltage + * + * Drivers implementing set_voltage_sel() and list_voltage() can use + * this as their map_voltage() operation. It will find a suitable + * voltage by calling list_voltage() until it gets something in bounds + * for the requested voltages. + */ +int regulator_map_voltage_iterate(struct regulator_dev *rdev, + int min_uV, int max_uV) +{ + int best_val = INT_MAX; + int selector = 0; + int i, ret; + + /* Find the smallest voltage that falls within the specified + * range. + */ + for (i = 0; i < rdev->desc->n_voltages; i++) { + ret = rdev->desc->ops->list_voltage(rdev, i); + if (ret < 0) + continue; + + if (ret < best_val && ret >= min_uV && ret <= max_uV) { + best_val = ret; + selector = i; + } + } + + if (best_val != INT_MAX) + return selector; + else + return -EINVAL; +} +EXPORT_SYMBOL_GPL(regulator_map_voltage_iterate); + +/** + * regulator_map_voltage_ascend - map_voltage() for ascendant voltage list + * + * @rdev: Regulator to operate on + * @min_uV: Lower bound for voltage + * @max_uV: Upper bound for voltage + * + * Drivers that have ascendant voltage list can use this as their + * map_voltage() operation. + */ +int regulator_map_voltage_ascend(struct regulator_dev *rdev, + int min_uV, int max_uV) +{ + int i, ret; + + for (i = 0; i < rdev->desc->n_voltages; i++) { + ret = rdev->desc->ops->list_voltage(rdev, i); + if (ret < 0) + continue; + + if (ret > max_uV) + break; + + if (ret >= min_uV && ret <= max_uV) + return i; + } + + return -EINVAL; +} +EXPORT_SYMBOL_GPL(regulator_map_voltage_ascend); + +/** + * regulator_map_voltage_linear - map_voltage() for simple linear mappings + * + * @rdev: Regulator to operate on + * @min_uV: Lower bound for voltage + * @max_uV: Upper bound for voltage + * + * Drivers providing min_uV and uV_step in their regulator_desc can + * use this as their map_voltage() operation. + */ +int regulator_map_voltage_linear(struct regulator_dev *rdev, + int min_uV, int max_uV) +{ + int ret, voltage; + + /* Allow uV_step to be 0 for fixed voltage */ + if (rdev->desc->n_voltages == 1 && rdev->desc->uV_step == 0) { + if (min_uV <= rdev->desc->min_uV && rdev->desc->min_uV <= max_uV) + return 0; + else + return -EINVAL; + } + + if (!rdev->desc->uV_step) { + BUG_ON(!rdev->desc->uV_step); + return -EINVAL; + } + + if (min_uV < rdev->desc->min_uV) + min_uV = rdev->desc->min_uV; + + ret = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step); + if (ret < 0) + return ret; + + ret += rdev->desc->linear_min_sel; + + /* Map back into a voltage to verify we're still in bounds */ + voltage = rdev->desc->ops->list_voltage(rdev, ret); + if (voltage < min_uV || voltage > max_uV) + return -EINVAL; + + return ret; +} +EXPORT_SYMBOL_GPL(regulator_map_voltage_linear); + +/** + * regulator_map_voltage_linear - map_voltage() for multiple linear ranges + * + * @rdev: Regulator to operate on + * @min_uV: Lower bound for voltage + * @max_uV: Upper bound for voltage + * + * Drivers providing linear_ranges in their descriptor can use this as + * their map_voltage() callback. + */ +int regulator_map_voltage_linear_range(struct regulator_dev *rdev, + int min_uV, int max_uV) +{ + const struct regulator_linear_range *range; + int ret = -EINVAL; + int voltage, i; + + if (!rdev->desc->n_linear_ranges) { + BUG_ON(!rdev->desc->n_linear_ranges); + return -EINVAL; + } + + for (i = 0; i < rdev->desc->n_linear_ranges; i++) { + range = &rdev->desc->linear_ranges[i]; + + if (!(min_uV <= range->max_uV && max_uV >= range->min_uV)) + continue; + + if (min_uV <= range->min_uV) + min_uV = range->min_uV; + + /* range->uV_step == 0 means fixed voltage range */ + if (range->uV_step == 0) { + ret = 0; + } else { + ret = DIV_ROUND_UP(min_uV - range->min_uV, + range->uV_step); + if (ret < 0) + return ret; + } + + ret += range->min_sel; + + break; + } + + if (i == rdev->desc->n_linear_ranges) + return -EINVAL; + + /* Map back into a voltage to verify we're still in bounds */ + voltage = rdev->desc->ops->list_voltage(rdev, ret); + if (voltage < min_uV || voltage > max_uV) + return -EINVAL; + + return ret; +} +EXPORT_SYMBOL_GPL(regulator_map_voltage_linear_range); + +/** + * regulator_list_voltage_linear - List voltages with simple calculation + * + * @rdev: Regulator device + * @selector: Selector to convert into a voltage + * + * Regulators with a simple linear mapping between voltages and + * selectors can set min_uV and uV_step in the regulator descriptor + * and then use this function as their list_voltage() operation, + */ +int regulator_list_voltage_linear(struct regulator_dev *rdev, + unsigned int selector) +{ + if (selector >= rdev->desc->n_voltages) + return -EINVAL; + if (selector < rdev->desc->linear_min_sel) + return 0; + + selector -= rdev->desc->linear_min_sel; + + return rdev->desc->min_uV + (rdev->desc->uV_step * selector); +} +EXPORT_SYMBOL_GPL(regulator_list_voltage_linear); + +/** + * regulator_list_voltage_linear_range - List voltages for linear ranges + * + * @rdev: Regulator device + * @selector: Selector to convert into a voltage + * + * Regulators with a series of simple linear mappings between voltages + * and selectors can set linear_ranges in the regulator descriptor and + * then use this function as their list_voltage() operation, + */ +int regulator_list_voltage_linear_range(struct regulator_dev *rdev, + unsigned int selector) +{ + const struct regulator_linear_range *range; + int i; + + if (!rdev->desc->n_linear_ranges) { + BUG_ON(!rdev->desc->n_linear_ranges); + return -EINVAL; + } + + for (i = 0; i < rdev->desc->n_linear_ranges; i++) { + range = &rdev->desc->linear_ranges[i]; + + if (!(selector >= range->min_sel && + selector <= range->max_sel)) + continue; + + selector -= range->min_sel; + + return range->min_uV + (range->uV_step * selector); + } + + return -EINVAL; +} +EXPORT_SYMBOL_GPL(regulator_list_voltage_linear_range); + +/** + * regulator_list_voltage_table - List voltages with table based mapping + * + * @rdev: Regulator device + * @selector: Selector to convert into a voltage + * + * Regulators with table based mapping between voltages and + * selectors can set volt_table in the regulator descriptor + * and then use this function as their list_voltage() operation. + */ +int regulator_list_voltage_table(struct regulator_dev *rdev, + unsigned int selector) +{ + if (!rdev->desc->volt_table) { + BUG_ON(!rdev->desc->volt_table); + return -EINVAL; + } + + if (selector >= rdev->desc->n_voltages) + return -EINVAL; + + return rdev->desc->volt_table[selector]; +} +EXPORT_SYMBOL_GPL(regulator_list_voltage_table); + +/** + * regulator_set_bypass_regmap - Default set_bypass() using regmap + * + * @rdev: device to operate on. + * @enable: state to set. + */ +int regulator_set_bypass_regmap(struct regulator_dev *rdev, bool enable) +{ + unsigned int val; + + if (enable) + val = rdev->desc->bypass_mask; + else + val = 0; + + return regmap_update_bits(rdev->regmap, rdev->desc->bypass_reg, + rdev->desc->bypass_mask, val); +} +EXPORT_SYMBOL_GPL(regulator_set_bypass_regmap); + +/** + * regulator_get_bypass_regmap - Default get_bypass() using regmap + * + * @rdev: device to operate on. + * @enable: current state. + */ +int regulator_get_bypass_regmap(struct regulator_dev *rdev, bool *enable) +{ + unsigned int val; + int ret; + + ret = regmap_read(rdev->regmap, rdev->desc->bypass_reg, &val); + if (ret != 0) + return ret; + + *enable = val & rdev->desc->bypass_mask; + + return 0; +} +EXPORT_SYMBOL_GPL(regulator_get_bypass_regmap); diff --git a/drivers/regulator/isl6271a-regulator.c b/drivers/regulator/isl6271a-regulator.c index b99c49b9aff0..88c1a3acf563 100644 --- a/drivers/regulator/isl6271a-regulator.c +++ b/drivers/regulator/isl6271a-regulator.c @@ -110,7 +110,7 @@ static int isl6271a_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { struct regulator_config config = { }; - struct regulator_init_data *init_data = i2c->dev.platform_data; + struct regulator_init_data *init_data = dev_get_platdata(&i2c->dev); struct isl_pmic *pmic; int err, i; diff --git a/drivers/regulator/lp3971.c b/drivers/regulator/lp3971.c index 3809b4381606..5a4604ee5ea5 100644 --- a/drivers/regulator/lp3971.c +++ b/drivers/regulator/lp3971.c @@ -425,7 +425,7 @@ static int lp3971_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { struct lp3971 *lp3971; - struct lp3971_platform_data *pdata = i2c->dev.platform_data; + struct lp3971_platform_data *pdata = dev_get_platdata(&i2c->dev); int ret; u16 val; diff --git a/drivers/regulator/lp3972.c b/drivers/regulator/lp3972.c index 573024039ca0..093e6f44ff8a 100644 --- a/drivers/regulator/lp3972.c +++ b/drivers/regulator/lp3972.c @@ -519,7 +519,7 @@ static int lp3972_i2c_probe(struct i2c_client *i2c, const struct i2c_device_id *id) { struct lp3972 *lp3972; - struct lp3972_platform_data *pdata = i2c->dev.platform_data; + struct lp3972_platform_data *pdata = dev_get_platdata(&i2c->dev); int ret; u16 val; diff --git a/drivers/regulator/lp872x.c b/drivers/regulator/lp872x.c index b16336bcd4d4..2b84b727a3c4 100644 --- a/drivers/regulator/lp872x.c +++ b/drivers/regulator/lp872x.c @@ -373,7 +373,7 @@ static int lp8725_buck_set_current_limit(struct regulator_dev *rdev, return -EINVAL; } - for (i = ARRAY_SIZE(lp8725_buck_uA) - 1 ; i >= 0; i--) { + for (i = ARRAY_SIZE(lp8725_buck_uA) - 1; i >= 0; i--) { if (lp8725_buck_uA[i] >= min_uA && lp8725_buck_uA[i] <= max_uA) return lp872x_update_bits(lp, addr, @@ -787,7 +787,7 @@ static int lp872x_regulator_register(struct lp872x *lp) struct regulator_dev *rdev; int i, ret; - for (i = 0 ; i < lp->num_regulators ; i++) { + for (i = 0; i < lp->num_regulators; i++) { desc = (lp->chipid == LP8720) ? &lp8720_regulator_desc[i] : &lp8725_regulator_desc[i]; @@ -820,7 +820,7 @@ static void lp872x_regulator_unregister(struct lp872x *lp) struct regulator_dev *rdev; int i; - for (i = 0 ; i < lp->num_regulators ; i++) { + for (i = 0; i < lp->num_regulators; i++) { rdev = *(lp->regulators + i); regulator_unregister(rdev); } @@ -907,7 +907,8 @@ static struct lp872x_platform_data goto out; for (i = 0; i < num_matches; i++) { - pdata->regulator_data[i].id = (int)match[i].driver_data; + pdata->regulator_data[i].id = + (enum lp872x_regulator_id)match[i].driver_data; pdata->regulator_data[i].init_data = match[i].init_data; /* Operation mode configuration for buck/buck1/buck2 */ @@ -961,7 +962,7 @@ static int lp872x_probe(struct i2c_client *cl, const struct i2c_device_id *id) } lp->dev = &cl->dev; - lp->pdata = cl->dev.platform_data; + lp->pdata = dev_get_platdata(&cl->dev); lp->chipid = id->driver_data; lp->num_regulators = num_regulators; i2c_set_clientdata(cl, lp); diff --git a/drivers/regulator/lp8755.c b/drivers/regulator/lp8755.c index d9e38b4c2adc..785a25e9a437 100644 --- a/drivers/regulator/lp8755.c +++ b/drivers/regulator/lp8755.c @@ -228,6 +228,7 @@ err_i2c: } static struct regulator_ops lp8755_buck_ops = { + .map_voltage = regulator_map_voltage_linear, .list_voltage = regulator_list_voltage_linear, .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, @@ -449,7 +450,7 @@ static int lp8755_probe(struct i2c_client *client, { int ret, icnt; struct lp8755_chip *pchip; - struct lp8755_platform_data *pdata = client->dev.platform_data; + struct lp8755_platform_data *pdata = dev_get_platdata(&client->dev); if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { dev_err(&client->dev, "i2c functionality check fail.\n"); diff --git a/drivers/regulator/max1586.c b/drivers/regulator/max1586.c index 54af61015814..3a599ee0a456 100644 --- a/drivers/regulator/max1586.c +++ b/drivers/regulator/max1586.c @@ -163,7 +163,7 @@ static int max1586_pmic_probe(struct i2c_client *client, const struct i2c_device_id *i2c_id) { struct regulator_dev **rdev; - struct max1586_platform_data *pdata = client->dev.platform_data; + struct max1586_platform_data *pdata = dev_get_platdata(&client->dev); struct regulator_config config = { }; struct max1586_data *max1586; int i, id, ret = -ENOMEM; diff --git a/drivers/regulator/max8649.c b/drivers/regulator/max8649.c index db6c9be10f3f..19c6f08eafd5 100644 --- a/drivers/regulator/max8649.c +++ b/drivers/regulator/max8649.c @@ -152,7 +152,7 @@ static struct regmap_config max8649_regmap_config = { static int max8649_regulator_probe(struct i2c_client *client, const struct i2c_device_id *id) { - struct max8649_platform_data *pdata = client->dev.platform_data; + struct max8649_platform_data *pdata = dev_get_platdata(&client->dev); struct max8649_regulator_info *info = NULL; struct regulator_config config = { }; unsigned int val; diff --git a/drivers/regulator/max8660.c b/drivers/regulator/max8660.c index d428ef9a626f..144bcacd734d 100644 --- a/drivers/regulator/max8660.c +++ b/drivers/regulator/max8660.c @@ -44,6 +44,9 @@ #include #include #include +#include +#include +#include #define MAX8660_DCDC_MIN_UV 725000 #define MAX8660_DCDC_MAX_UV 1800000 @@ -305,21 +308,105 @@ static const struct regulator_desc max8660_reg[] = { }, }; +enum { + MAX8660 = 0, + MAX8661 = 1, +}; + +#ifdef CONFIG_OF +static const struct of_device_id max8660_dt_ids[] = { + { .compatible = "maxim,max8660", .data = (void *) MAX8660 }, + { .compatible = "maxim,max8661", .data = (void *) MAX8661 }, + { } +}; +MODULE_DEVICE_TABLE(of, max8660_dt_ids); + +static int max8660_pdata_from_dt(struct device *dev, + struct device_node **of_node, + struct max8660_platform_data *pdata) +{ + int matched, i; + struct device_node *np; + struct max8660_subdev_data *sub; + struct of_regulator_match rmatch[ARRAY_SIZE(max8660_reg)]; + + np = of_find_node_by_name(dev->of_node, "regulators"); + if (!np) { + dev_err(dev, "missing 'regulators' subnode in DT\n"); + return -EINVAL; + } + + for (i = 0; i < ARRAY_SIZE(rmatch); i++) + rmatch[i].name = max8660_reg[i].name; + + matched = of_regulator_match(dev, np, rmatch, ARRAY_SIZE(rmatch)); + if (matched <= 0) + return matched; + + pdata->subdevs = devm_kzalloc(dev, sizeof(struct max8660_subdev_data) * + matched, GFP_KERNEL); + if (!pdata->subdevs) + return -ENOMEM; + + pdata->num_subdevs = matched; + sub = pdata->subdevs; + + for (i = 0; i < matched; i++) { + sub->id = i; + sub->name = rmatch[i].name; + sub->platform_data = rmatch[i].init_data; + of_node[i] = rmatch[i].of_node; + sub++; + } + + return 0; +} +#else +static inline int max8660_pdata_from_dt(struct device *dev, + struct device_node **of_node, + struct max8660_platform_data *pdata) +{ + return 0; +} +#endif + static int max8660_probe(struct i2c_client *client, const struct i2c_device_id *i2c_id) { struct regulator_dev **rdev; - struct max8660_platform_data *pdata = client->dev.platform_data; + struct device *dev = &client->dev; + struct max8660_platform_data *pdata = dev_get_platdata(dev); struct regulator_config config = { }; struct max8660 *max8660; int boot_on, i, id, ret = -EINVAL; + struct device_node *of_node[MAX8660_V_END]; + unsigned long type; + + if (dev->of_node && !pdata) { + const struct of_device_id *id; + struct max8660_platform_data pdata_of; + + id = of_match_device(of_match_ptr(max8660_dt_ids), dev); + if (!id) + return -ENODEV; + + ret = max8660_pdata_from_dt(dev, of_node, &pdata_of); + if (ret < 0) + return ret; + + pdata = &pdata_of; + type = (unsigned long) id->data; + } else { + type = i2c_id->driver_data; + memset(of_node, 0, sizeof(of_node)); + } if (pdata->num_subdevs > MAX8660_V_END) { - dev_err(&client->dev, "Too many regulators found!\n"); + dev_err(dev, "Too many regulators found!\n"); return -EINVAL; } - max8660 = devm_kzalloc(&client->dev, sizeof(struct max8660) + + max8660 = devm_kzalloc(dev, sizeof(struct max8660) + sizeof(struct regulator_dev *) * MAX8660_V_END, GFP_KERNEL); if (!max8660) @@ -376,8 +463,8 @@ static int max8660_probe(struct i2c_client *client, break; case MAX8660_V7: - if (!strcmp(i2c_id->name, "max8661")) { - dev_err(&client->dev, "Regulator not on this chip!\n"); + if (type == MAX8661) { + dev_err(dev, "Regulator not on this chip!\n"); goto err_out; } @@ -386,7 +473,7 @@ static int max8660_probe(struct i2c_client *client, break; default: - dev_err(&client->dev, "invalid regulator %s\n", + dev_err(dev, "invalid regulator %s\n", pdata->subdevs[i].name); goto err_out; } @@ -397,14 +484,15 @@ static int max8660_probe(struct i2c_client *client, id = pdata->subdevs[i].id; - config.dev = &client->dev; + config.dev = dev; config.init_data = pdata->subdevs[i].platform_data; + config.of_node = of_node[i]; config.driver_data = max8660; rdev[i] = regulator_register(&max8660_reg[id], &config); if (IS_ERR(rdev[i])) { ret = PTR_ERR(rdev[i]); - dev_err(&client->dev, "failed to register %s\n", + dev_err(dev, "failed to register %s\n", max8660_reg[id].name); goto err_unregister; } @@ -431,8 +519,8 @@ static int max8660_remove(struct i2c_client *client) } static const struct i2c_device_id max8660_id[] = { - { "max8660", 0 }, - { "max8661", 0 }, + { .name = "max8660", .driver_data = MAX8660 }, + { .name = "max8661", .driver_data = MAX8661 }, { } }; MODULE_DEVICE_TABLE(i2c, max8660_id); diff --git a/drivers/regulator/max8925-regulator.c b/drivers/regulator/max8925-regulator.c index e6d54a546d36..d80b5fa758ae 100644 --- a/drivers/regulator/max8925-regulator.c +++ b/drivers/regulator/max8925-regulator.c @@ -277,7 +277,7 @@ static int max8925_regulator_dt_init(struct platform_device *pdev, static int max8925_regulator_probe(struct platform_device *pdev) { struct max8925_chip *chip = dev_get_drvdata(pdev->dev.parent); - struct regulator_init_data *pdata = pdev->dev.platform_data; + struct regulator_init_data *pdata = dev_get_platdata(&pdev->dev); struct regulator_config config = { }; struct max8925_regulator_info *ri; struct resource *res; diff --git a/drivers/regulator/max8952.c b/drivers/regulator/max8952.c index 5259c2fea90a..788e5ae2af1b 100644 --- a/drivers/regulator/max8952.c +++ b/drivers/regulator/max8952.c @@ -196,7 +196,7 @@ static int max8952_pmic_probe(struct i2c_client *client, const struct i2c_device_id *i2c_id) { struct i2c_adapter *adapter = to_i2c_adapter(client->dev.parent); - struct max8952_platform_data *pdata = client->dev.platform_data; + struct max8952_platform_data *pdata = dev_get_platdata(&client->dev); struct regulator_config config = { }; struct max8952_data *max8952; diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c index 0c5195a842e2..5b77ab7762e4 100644 --- a/drivers/regulator/max8973-regulator.c +++ b/drivers/regulator/max8973-regulator.c @@ -371,7 +371,7 @@ static int max8973_probe(struct i2c_client *client, struct max8973_chip *max; int ret; - pdata = client->dev.platform_data; + pdata = dev_get_platdata(&client->dev); if (!pdata && !client->dev.of_node) { dev_err(&client->dev, "No Platform data"); diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c index f3c8f8f9dc39..7827384680d6 100644 --- a/drivers/regulator/of_regulator.c +++ b/drivers/regulator/of_regulator.c @@ -21,6 +21,7 @@ static void of_get_regulation_constraints(struct device_node *np, { const __be32 *min_uV, *max_uV, *uV_offset; const __be32 *min_uA, *max_uA, *ramp_delay; + struct property *prop; struct regulation_constraints *constraints = &(*init_data)->constraints; constraints->name = of_get_property(np, "regulator-name", NULL); @@ -64,9 +65,14 @@ static void of_get_regulation_constraints(struct device_node *np, if (of_property_read_bool(np, "regulator-allow-bypass")) constraints->valid_ops_mask |= REGULATOR_CHANGE_BYPASS; - ramp_delay = of_get_property(np, "regulator-ramp-delay", NULL); - if (ramp_delay) - constraints->ramp_delay = be32_to_cpu(*ramp_delay); + prop = of_find_property(np, "regulator-ramp-delay", NULL); + if (prop && prop->value) { + ramp_delay = prop->value; + if (*ramp_delay) + constraints->ramp_delay = be32_to_cpu(*ramp_delay); + else + constraints->ramp_disable = true; + } } /** diff --git a/drivers/regulator/palmas-regulator.c b/drivers/regulator/palmas-regulator.c index d0c87856dd25..488dfe7ce9a6 100644 --- a/drivers/regulator/palmas-regulator.c +++ b/drivers/regulator/palmas-regulator.c @@ -97,10 +97,15 @@ static const struct regs_info palmas_regs_info[] = { .ctrl_addr = PALMAS_SMPS9_CTRL, }, { - .name = "SMPS10", + .name = "SMPS10_OUT2", .sname = "smps10-in", .ctrl_addr = PALMAS_SMPS10_CTRL, }, + { + .name = "SMPS10_OUT1", + .sname = "smps10-out2", + .ctrl_addr = PALMAS_SMPS10_CTRL, + }, { .name = "LDO1", .sname = "ldo1-in", @@ -487,6 +492,8 @@ static struct regulator_ops palmas_ops_smps10 = { .set_voltage_sel = regulator_set_voltage_sel_regmap, .list_voltage = regulator_list_voltage_linear, .map_voltage = regulator_map_voltage_linear, + .set_bypass = regulator_set_bypass_regmap, + .get_bypass = regulator_get_bypass_regmap, }; static int palmas_is_enabled_ldo(struct regulator_dev *dev) @@ -538,7 +545,8 @@ static int palmas_smps_init(struct palmas *palmas, int id, return ret; switch (id) { - case PALMAS_REG_SMPS10: + case PALMAS_REG_SMPS10_OUT1: + case PALMAS_REG_SMPS10_OUT2: reg &= ~PALMAS_SMPS10_CTRL_MODE_SLEEP_MASK; if (reg_init->mode_sleep) reg |= reg_init->mode_sleep << @@ -681,7 +689,8 @@ static struct of_regulator_match palmas_matches[] = { { .name = "smps7", }, { .name = "smps8", }, { .name = "smps9", }, - { .name = "smps10", }, + { .name = "smps10_out2", }, + { .name = "smps10_out1", }, { .name = "ldo1", }, { .name = "ldo2", }, { .name = "ldo3", }, @@ -765,7 +774,7 @@ static void palmas_dt_to_pdata(struct device *dev, static int palmas_regulators_probe(struct platform_device *pdev) { struct palmas *palmas = dev_get_drvdata(pdev->dev.parent); - struct palmas_pmic_platform_data *pdata = pdev->dev.platform_data; + struct palmas_pmic_platform_data *pdata = dev_get_platdata(&pdev->dev); struct device_node *node = pdev->dev.of_node; struct regulator_dev *rdev; struct regulator_config config = { }; @@ -838,7 +847,8 @@ static int palmas_regulators_probe(struct platform_device *pdev) continue; ramp_delay_support = true; break; - case PALMAS_REG_SMPS10: + case PALMAS_REG_SMPS10_OUT1: + case PALMAS_REG_SMPS10_OUT2: if (!PALMAS_PMIC_HAS(palmas, SMPS10_BOOST)) continue; } @@ -872,7 +882,8 @@ static int palmas_regulators_probe(struct platform_device *pdev) pmic->desc[id].id = id; switch (id) { - case PALMAS_REG_SMPS10: + case PALMAS_REG_SMPS10_OUT1: + case PALMAS_REG_SMPS10_OUT2: pmic->desc[id].n_voltages = PALMAS_SMPS10_NUM_VOLTAGES; pmic->desc[id].ops = &palmas_ops_smps10; pmic->desc[id].vsel_reg = @@ -882,7 +893,14 @@ static int palmas_regulators_probe(struct platform_device *pdev) pmic->desc[id].enable_reg = PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE, PALMAS_SMPS10_CTRL); - pmic->desc[id].enable_mask = SMPS10_BOOST_EN; + if (id == PALMAS_REG_SMPS10_OUT1) + pmic->desc[id].enable_mask = SMPS10_SWITCH_EN; + else + pmic->desc[id].enable_mask = SMPS10_BOOST_EN; + pmic->desc[id].bypass_reg = + PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE, + PALMAS_SMPS10_CTRL); + pmic->desc[id].bypass_mask = SMPS10_BYPASS_EN; pmic->desc[id].min_uV = 3750000; pmic->desc[id].uV_step = 1250000; break; diff --git a/drivers/regulator/pcap-regulator.c b/drivers/regulator/pcap-regulator.c index 1a73a297fe73..b49eaeedea84 100644 --- a/drivers/regulator/pcap-regulator.c +++ b/drivers/regulator/pcap-regulator.c @@ -243,7 +243,7 @@ static int pcap_regulator_probe(struct platform_device *pdev) struct regulator_config config = { }; config.dev = &pdev->dev; - config.init_data = pdev->dev.platform_data; + config.init_data = dev_get_platdata(&pdev->dev); config.driver_data = pcap; rdev = regulator_register(&pcap_regulators[pdev->id], &config); diff --git a/drivers/regulator/pcf50633-regulator.c b/drivers/regulator/pcf50633-regulator.c index 54df9f7cb504..0f3576d48abf 100644 --- a/drivers/regulator/pcf50633-regulator.c +++ b/drivers/regulator/pcf50633-regulator.c @@ -86,7 +86,7 @@ static int pcf50633_regulator_probe(struct platform_device *pdev) pcf = dev_to_pcf50633(pdev->dev.parent); config.dev = &pdev->dev; - config.init_data = pdev->dev.platform_data; + config.init_data = dev_get_platdata(&pdev->dev); config.driver_data = pcf; config.regmap = pcf->regmap; diff --git a/drivers/regulator/pfuze100-regulator.c b/drivers/regulator/pfuze100-regulator.c new file mode 100644 index 000000000000..ba67b2c4e2e7 --- /dev/null +++ b/drivers/regulator/pfuze100-regulator.c @@ -0,0 +1,445 @@ +/* + * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define PFUZE_NUMREGS 128 +#define PFUZE100_VOL_OFFSET 0 +#define PFUZE100_STANDBY_OFFSET 1 +#define PFUZE100_MODE_OFFSET 3 +#define PFUZE100_CONF_OFFSET 4 + +#define PFUZE100_DEVICEID 0x0 +#define PFUZE100_REVID 0x3 +#define PFUZE100_FABID 0x3 + +#define PFUZE100_SW1ABVOL 0x20 +#define PFUZE100_SW1CVOL 0x2e +#define PFUZE100_SW2VOL 0x35 +#define PFUZE100_SW3AVOL 0x3c +#define PFUZE100_SW3BVOL 0x43 +#define PFUZE100_SW4VOL 0x4a +#define PFUZE100_SWBSTCON1 0x66 +#define PFUZE100_VREFDDRCON 0x6a +#define PFUZE100_VSNVSVOL 0x6b +#define PFUZE100_VGEN1VOL 0x6c +#define PFUZE100_VGEN2VOL 0x6d +#define PFUZE100_VGEN3VOL 0x6e +#define PFUZE100_VGEN4VOL 0x6f +#define PFUZE100_VGEN5VOL 0x70 +#define PFUZE100_VGEN6VOL 0x71 + +struct pfuze_regulator { + struct regulator_desc desc; + unsigned char stby_reg; + unsigned char stby_mask; +}; + +struct pfuze_chip { + struct regmap *regmap; + struct device *dev; + struct pfuze_regulator regulator_descs[PFUZE100_MAX_REGULATOR]; + struct regulator_dev *regulators[PFUZE100_MAX_REGULATOR]; +}; + +static const int pfuze100_swbst[] = { + 5000000, 5050000, 5100000, 5150000, +}; + +static const int pfuze100_vsnvs[] = { + 1000000, 1100000, 1200000, 1300000, 1500000, 1800000, 3000000, +}; + +static const struct i2c_device_id pfuze_device_id[] = { + {.name = "pfuze100"}, + {}, +}; +MODULE_DEVICE_TABLE(i2c, pfuze_device_id); + +static const struct of_device_id pfuze_dt_ids[] = { + { .compatible = "fsl,pfuze100" }, + {}, +}; +MODULE_DEVICE_TABLE(of, pfuze_dt_ids); + +static int pfuze100_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay) +{ + struct pfuze_chip *pfuze100 = rdev_get_drvdata(rdev); + int id = rdev->desc->id; + unsigned int ramp_bits; + int ret; + + if (id < PFUZE100_SWBST) { + ramp_delay = 12500 / ramp_delay; + ramp_bits = (ramp_delay >> 1) - (ramp_delay >> 3); + ret = regmap_update_bits(pfuze100->regmap, + rdev->desc->vsel_reg + 4, + 0xc0, ramp_bits << 6); + if (ret < 0) + dev_err(pfuze100->dev, "ramp failed, err %d\n", ret); + } else + ret = -EACCES; + + return ret; +} + +static struct regulator_ops pfuze100_ldo_regulator_ops = { + .enable = regulator_enable_regmap, + .disable = regulator_disable_regmap, + .is_enabled = regulator_is_enabled_regmap, + .list_voltage = regulator_list_voltage_linear, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, +}; + +static struct regulator_ops pfuze100_fixed_regulator_ops = { + .list_voltage = regulator_list_voltage_linear, +}; + +static struct regulator_ops pfuze100_sw_regulator_ops = { + .list_voltage = regulator_list_voltage_linear, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + .set_voltage_time_sel = regulator_set_voltage_time_sel, + .set_ramp_delay = pfuze100_set_ramp_delay, +}; + +static struct regulator_ops pfuze100_swb_regulator_ops = { + .list_voltage = regulator_list_voltage_table, + .map_voltage = regulator_map_voltage_ascend, + .set_voltage_sel = regulator_set_voltage_sel_regmap, + .get_voltage_sel = regulator_get_voltage_sel_regmap, + +}; + +#define PFUZE100_FIXED_REG(_name, base, voltage) \ + [PFUZE100_ ## _name] = { \ + .desc = { \ + .name = #_name, \ + .n_voltages = 1, \ + .ops = &pfuze100_fixed_regulator_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = PFUZE100_ ## _name, \ + .owner = THIS_MODULE, \ + .min_uV = (voltage), \ + .enable_reg = (base), \ + .enable_mask = 0x10, \ + }, \ + } + +#define PFUZE100_SW_REG(_name, base, min, max, step) \ + [PFUZE100_ ## _name] = { \ + .desc = { \ + .name = #_name,\ + .n_voltages = ((max) - (min)) / (step) + 1, \ + .ops = &pfuze100_sw_regulator_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = PFUZE100_ ## _name, \ + .owner = THIS_MODULE, \ + .min_uV = (min), \ + .uV_step = (step), \ + .vsel_reg = (base) + PFUZE100_VOL_OFFSET, \ + .vsel_mask = 0x3f, \ + }, \ + .stby_reg = (base) + PFUZE100_STANDBY_OFFSET, \ + .stby_mask = 0x3f, \ + } + +#define PFUZE100_SWB_REG(_name, base, mask, voltages) \ + [PFUZE100_ ## _name] = { \ + .desc = { \ + .name = #_name, \ + .n_voltages = ARRAY_SIZE(voltages), \ + .ops = &pfuze100_swb_regulator_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = PFUZE100_ ## _name, \ + .owner = THIS_MODULE, \ + .volt_table = voltages, \ + .vsel_reg = (base), \ + .vsel_mask = (mask), \ + }, \ + } + +#define PFUZE100_VGEN_REG(_name, base, min, max, step) \ + [PFUZE100_ ## _name] = { \ + .desc = { \ + .name = #_name, \ + .n_voltages = ((max) - (min)) / (step) + 1, \ + .ops = &pfuze100_ldo_regulator_ops, \ + .type = REGULATOR_VOLTAGE, \ + .id = PFUZE100_ ## _name, \ + .owner = THIS_MODULE, \ + .min_uV = (min), \ + .uV_step = (step), \ + .vsel_reg = (base), \ + .vsel_mask = 0xf, \ + .enable_reg = (base), \ + .enable_mask = 0x10, \ + }, \ + .stby_reg = (base), \ + .stby_mask = 0x20, \ + } + +static struct pfuze_regulator pfuze100_regulators[] = { + PFUZE100_SW_REG(SW1AB, PFUZE100_SW1ABVOL, 300000, 1875000, 25000), + PFUZE100_SW_REG(SW1C, PFUZE100_SW1CVOL, 300000, 1875000, 25000), + PFUZE100_SW_REG(SW2, PFUZE100_SW2VOL, 400000, 1975000, 25000), + PFUZE100_SW_REG(SW3A, PFUZE100_SW3AVOL, 400000, 1975000, 25000), + PFUZE100_SW_REG(SW3B, PFUZE100_SW3BVOL, 400000, 1975000, 25000), + PFUZE100_SW_REG(SW4, PFUZE100_SW4VOL, 400000, 1975000, 25000), + PFUZE100_SWB_REG(SWBST, PFUZE100_SWBSTCON1, 0x3 , pfuze100_swbst), + PFUZE100_SWB_REG(VSNVS, PFUZE100_VSNVSVOL, 0x7, pfuze100_vsnvs), + PFUZE100_FIXED_REG(VREFDDR, PFUZE100_VREFDDRCON, 750000), + PFUZE100_VGEN_REG(VGEN1, PFUZE100_VGEN1VOL, 800000, 1550000, 50000), + PFUZE100_VGEN_REG(VGEN2, PFUZE100_VGEN2VOL, 800000, 1550000, 50000), + PFUZE100_VGEN_REG(VGEN3, PFUZE100_VGEN3VOL, 1800000, 3300000, 100000), + PFUZE100_VGEN_REG(VGEN4, PFUZE100_VGEN4VOL, 1800000, 3300000, 100000), + PFUZE100_VGEN_REG(VGEN5, PFUZE100_VGEN5VOL, 1800000, 3300000, 100000), + PFUZE100_VGEN_REG(VGEN6, PFUZE100_VGEN6VOL, 1800000, 3300000, 100000), +}; + +#ifdef CONFIG_OF +static struct of_regulator_match pfuze100_matches[] = { + { .name = "sw1ab", }, + { .name = "sw1c", }, + { .name = "sw2", }, + { .name = "sw3a", }, + { .name = "sw3b", }, + { .name = "sw4", }, + { .name = "swbst", }, + { .name = "vsnvs", }, + { .name = "vrefddr", }, + { .name = "vgen1", }, + { .name = "vgen2", }, + { .name = "vgen3", }, + { .name = "vgen4", }, + { .name = "vgen5", }, + { .name = "vgen6", }, +}; + +static int pfuze_parse_regulators_dt(struct pfuze_chip *chip) +{ + struct device *dev = chip->dev; + struct device_node *np, *parent; + int ret; + + np = of_node_get(dev->parent->of_node); + if (!np) + return 0; + + parent = of_find_node_by_name(np, "regulators"); + if (!parent) { + dev_err(dev, "regulators node not found\n"); + return -EINVAL; + } + + ret = of_regulator_match(dev, parent, pfuze100_matches, + ARRAY_SIZE(pfuze100_matches)); + + of_node_put(parent); + if (ret < 0) { + dev_err(dev, "Error parsing regulator init data: %d\n", + ret); + return ret; + } + + return 0; +} + +static inline struct regulator_init_data *match_init_data(int index) +{ + return pfuze100_matches[index].init_data; +} + +static inline struct device_node *match_of_node(int index) +{ + return pfuze100_matches[index].of_node; +} +#else +static int pfuze_parse_regulators_dt(struct pfuze_chip *chip) +{ + return 0; +} + +static inline struct regulator_init_data *match_init_data(int index) +{ + return NULL; +} + +static inline struct device_node *match_of_node(int index) +{ + return NULL; +} +#endif + +static int pfuze_identify(struct pfuze_chip *pfuze_chip) +{ + unsigned int value; + int ret; + + ret = regmap_read(pfuze_chip->regmap, PFUZE100_DEVICEID, &value); + if (ret) + return ret; + + if (value & 0x0f) { + dev_warn(pfuze_chip->dev, "Illegal ID: %x\n", value); + return -ENODEV; + } + + ret = regmap_read(pfuze_chip->regmap, PFUZE100_REVID, &value); + if (ret) + return ret; + dev_info(pfuze_chip->dev, + "Full lay: %x, Metal lay: %x\n", + (value & 0xf0) >> 4, value & 0x0f); + + ret = regmap_read(pfuze_chip->regmap, PFUZE100_FABID, &value); + if (ret) + return ret; + dev_info(pfuze_chip->dev, "FAB: %x, FIN: %x\n", + (value & 0xc) >> 2, value & 0x3); + + return 0; +} + +static const struct regmap_config pfuze_regmap_config = { + .reg_bits = 8, + .val_bits = 8, + .max_register = PFUZE_NUMREGS - 1, + .cache_type = REGCACHE_RBTREE, +}; + +static int pfuze100_regulator_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct pfuze_chip *pfuze_chip; + struct pfuze_regulator_platform_data *pdata = + dev_get_platdata(&client->dev); + struct regulator_config config = { }; + int i, ret; + + pfuze_chip = devm_kzalloc(&client->dev, sizeof(*pfuze_chip), + GFP_KERNEL); + if (!pfuze_chip) + return -ENOMEM; + + i2c_set_clientdata(client, pfuze_chip); + + memcpy(pfuze_chip->regulator_descs, pfuze100_regulators, + sizeof(pfuze_chip->regulator_descs)); + + pfuze_chip->dev = &client->dev; + + pfuze_chip->regmap = devm_regmap_init_i2c(client, &pfuze_regmap_config); + if (IS_ERR(pfuze_chip->regmap)) { + ret = PTR_ERR(pfuze_chip->regmap); + dev_err(&client->dev, + "regmap allocation failed with err %d\n", ret); + return ret; + } + + ret = pfuze_identify(pfuze_chip); + if (ret) { + dev_err(&client->dev, "unrecognized pfuze chip ID!\n"); + return ret; + } + + ret = pfuze_parse_regulators_dt(pfuze_chip); + if (ret) + return ret; + + for (i = 0; i < PFUZE100_MAX_REGULATOR; i++) { + struct regulator_init_data *init_data; + struct regulator_desc *desc; + int val; + + desc = &pfuze_chip->regulator_descs[i].desc; + + if (pdata) + init_data = pdata->init_data[i]; + else + init_data = match_init_data(i); + + /* SW2~SW4 high bit check and modify the voltage value table */ + if (i > PFUZE100_SW1C && i < PFUZE100_SWBST) { + regmap_read(pfuze_chip->regmap, desc->vsel_reg, &val); + if (val & 0x40) { + desc->min_uV = 800000; + desc->uV_step = 50000; + desc->n_voltages = 51; + } + } + + config.dev = &client->dev; + config.init_data = init_data; + config.driver_data = pfuze_chip; + config.of_node = match_of_node(i); + + pfuze_chip->regulators[i] = regulator_register(desc, &config); + if (IS_ERR(pfuze_chip->regulators[i])) { + dev_err(&client->dev, "register regulator%s failed\n", + pfuze100_regulators[i].desc.name); + ret = PTR_ERR(pfuze_chip->regulators[i]); + while (--i >= 0) + regulator_unregister(pfuze_chip->regulators[i]); + return ret; + } + } + + return 0; +} + +static int pfuze100_regulator_remove(struct i2c_client *client) +{ + int i; + struct pfuze_chip *pfuze_chip = i2c_get_clientdata(client); + + for (i = 0; i < PFUZE100_MAX_REGULATOR; i++) + regulator_unregister(pfuze_chip->regulators[i]); + + return 0; +} + +static struct i2c_driver pfuze_driver = { + .id_table = pfuze_device_id, + .driver = { + .name = "pfuze100-regulator", + .owner = THIS_MODULE, + .of_match_table = pfuze_dt_ids, + }, + .probe = pfuze100_regulator_probe, + .remove = pfuze100_regulator_remove, +}; +module_i2c_driver(pfuze_driver); + +MODULE_AUTHOR("Robin Gong "); +MODULE_DESCRIPTION("Regulator Driver for Freescale PFUZE100 PMIC"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("i2c:pfuze100-regulator"); diff --git a/drivers/regulator/s2mps11.c b/drivers/regulator/s2mps11.c index 2f62564ca936..5eba2ff8c0e8 100644 --- a/drivers/regulator/s2mps11.c +++ b/drivers/regulator/s2mps11.c @@ -16,12 +16,17 @@ #include #include #include +#include +#include #include #include #include +#include #include #include +#define S2MPS11_REGULATOR_CNT ARRAY_SIZE(regulators) + struct s2mps11_info { struct regulator_dev *rdev[S2MPS11_REGULATOR_MAX]; @@ -31,11 +36,6 @@ struct s2mps11_info { int ramp_delay16; int ramp_delay7810; int ramp_delay9; - - bool buck6_ramp; - bool buck2_ramp; - bool buck3_ramp; - bool buck4_ramp; }; static int get_ramp_delay(int ramp_delay) @@ -50,9 +50,171 @@ static int get_ramp_delay(int ramp_delay) break; cnt++; } + + if (cnt > 3) + cnt = 3; + return cnt; } +static int s2mps11_regulator_set_voltage_time_sel(struct regulator_dev *rdev, + unsigned int old_selector, + unsigned int new_selector) +{ + struct s2mps11_info *s2mps11 = rdev_get_drvdata(rdev); + unsigned int ramp_delay = 0; + int old_volt, new_volt; + + switch (rdev->desc->id) { + case S2MPS11_BUCK2: + ramp_delay = s2mps11->ramp_delay2; + break; + case S2MPS11_BUCK3: + ramp_delay = s2mps11->ramp_delay34; + break; + case S2MPS11_BUCK4: + ramp_delay = s2mps11->ramp_delay34; + break; + case S2MPS11_BUCK5: + ramp_delay = s2mps11->ramp_delay5; + break; + case S2MPS11_BUCK6: + case S2MPS11_BUCK1: + ramp_delay = s2mps11->ramp_delay16; + break; + case S2MPS11_BUCK7: + case S2MPS11_BUCK8: + case S2MPS11_BUCK10: + ramp_delay = s2mps11->ramp_delay7810; + break; + case S2MPS11_BUCK9: + ramp_delay = s2mps11->ramp_delay9; + } + + if (ramp_delay == 0) + ramp_delay = rdev->desc->ramp_delay; + + old_volt = rdev->desc->min_uV + (rdev->desc->uV_step * old_selector); + new_volt = rdev->desc->min_uV + (rdev->desc->uV_step * new_selector); + + return DIV_ROUND_UP(abs(new_volt - old_volt), ramp_delay); +} + +static int s2mps11_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay) +{ + struct s2mps11_info *s2mps11 = rdev_get_drvdata(rdev); + unsigned int ramp_val, ramp_shift, ramp_reg = S2MPS11_REG_RAMP_BUCK; + unsigned int ramp_enable = 1, enable_shift = 0; + int ret; + + switch (rdev->desc->id) { + case S2MPS11_BUCK1: + if (ramp_delay > s2mps11->ramp_delay16) + s2mps11->ramp_delay16 = ramp_delay; + else + ramp_delay = s2mps11->ramp_delay16; + + ramp_shift = S2MPS11_BUCK16_RAMP_SHIFT; + break; + case S2MPS11_BUCK2: + enable_shift = S2MPS11_BUCK2_RAMP_EN_SHIFT; + if (!ramp_delay) { + ramp_enable = 0; + break; + } + + s2mps11->ramp_delay2 = ramp_delay; + ramp_shift = S2MPS11_BUCK2_RAMP_SHIFT; + ramp_reg = S2MPS11_REG_RAMP; + break; + case S2MPS11_BUCK3: + enable_shift = S2MPS11_BUCK3_RAMP_EN_SHIFT; + if (!ramp_delay) { + ramp_enable = 0; + break; + } + + if (ramp_delay > s2mps11->ramp_delay34) + s2mps11->ramp_delay34 = ramp_delay; + else + ramp_delay = s2mps11->ramp_delay34; + + ramp_shift = S2MPS11_BUCK34_RAMP_SHIFT; + ramp_reg = S2MPS11_REG_RAMP; + break; + case S2MPS11_BUCK4: + enable_shift = S2MPS11_BUCK4_RAMP_EN_SHIFT; + if (!ramp_delay) { + ramp_enable = 0; + break; + } + + if (ramp_delay > s2mps11->ramp_delay34) + s2mps11->ramp_delay34 = ramp_delay; + else + ramp_delay = s2mps11->ramp_delay34; + + ramp_shift = S2MPS11_BUCK34_RAMP_SHIFT; + ramp_reg = S2MPS11_REG_RAMP; + break; + case S2MPS11_BUCK5: + s2mps11->ramp_delay5 = ramp_delay; + ramp_shift = S2MPS11_BUCK5_RAMP_SHIFT; + break; + case S2MPS11_BUCK6: + enable_shift = S2MPS11_BUCK6_RAMP_EN_SHIFT; + if (!ramp_delay) { + ramp_enable = 0; + break; + } + + if (ramp_delay > s2mps11->ramp_delay16) + s2mps11->ramp_delay16 = ramp_delay; + else + ramp_delay = s2mps11->ramp_delay16; + + ramp_shift = S2MPS11_BUCK16_RAMP_SHIFT; + break; + case S2MPS11_BUCK7: + case S2MPS11_BUCK8: + case S2MPS11_BUCK10: + if (ramp_delay > s2mps11->ramp_delay7810) + s2mps11->ramp_delay7810 = ramp_delay; + else + ramp_delay = s2mps11->ramp_delay7810; + + ramp_shift = S2MPS11_BUCK7810_RAMP_SHIFT; + break; + case S2MPS11_BUCK9: + s2mps11->ramp_delay9 = ramp_delay; + ramp_shift = S2MPS11_BUCK9_RAMP_SHIFT; + break; + default: + return 0; + } + + if (!ramp_enable) + goto ramp_disable; + + if (enable_shift) { + ret = regmap_update_bits(rdev->regmap, S2MPS11_REG_RAMP, + 1 << enable_shift, 1 << enable_shift); + if (ret) { + dev_err(&rdev->dev, "failed to enable ramp rate\n"); + return ret; + } + } + + ramp_val = get_ramp_delay(ramp_delay); + + return regmap_update_bits(rdev->regmap, ramp_reg, 0x3 << ramp_shift, + ramp_val << ramp_shift); + +ramp_disable: + return regmap_update_bits(rdev->regmap, S2MPS11_REG_RAMP, + 1 << enable_shift, 0); +} + static struct regulator_ops s2mps11_ldo_ops = { .list_voltage = regulator_list_voltage_linear, .map_voltage = regulator_map_voltage_linear, @@ -72,7 +234,8 @@ static struct regulator_ops s2mps11_buck_ops = { .disable = regulator_disable_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, - .set_voltage_time_sel = regulator_set_voltage_time_sel, + .set_voltage_time_sel = s2mps11_regulator_set_voltage_time_sel, + .set_ramp_delay = s2mps11_set_ramp_delay, }; #define regulator_desc_ldo1(num) { \ @@ -239,59 +402,51 @@ static int s2mps11_pmic_probe(struct platform_device *pdev) { struct sec_pmic_dev *iodev = dev_get_drvdata(pdev->dev.parent); struct sec_platform_data *pdata = dev_get_platdata(iodev->dev); + struct of_regulator_match rdata[S2MPS11_REGULATOR_MAX]; + struct device_node *reg_np = NULL; struct regulator_config config = { }; struct s2mps11_info *s2mps11; int i, ret; - unsigned char ramp_enable, ramp_reg = 0; - - if (!pdata) { - dev_err(pdev->dev.parent, "Platform data not supplied\n"); - return -ENODEV; - } s2mps11 = devm_kzalloc(&pdev->dev, sizeof(struct s2mps11_info), GFP_KERNEL); if (!s2mps11) return -ENOMEM; - platform_set_drvdata(pdev, s2mps11); - - s2mps11->ramp_delay2 = pdata->buck2_ramp_delay; - s2mps11->ramp_delay34 = pdata->buck34_ramp_delay; - s2mps11->ramp_delay5 = pdata->buck5_ramp_delay; - s2mps11->ramp_delay16 = pdata->buck16_ramp_delay; - s2mps11->ramp_delay7810 = pdata->buck7810_ramp_delay; - s2mps11->ramp_delay9 = pdata->buck9_ramp_delay; - - s2mps11->buck6_ramp = pdata->buck6_ramp_enable; - s2mps11->buck2_ramp = pdata->buck2_ramp_enable; - s2mps11->buck3_ramp = pdata->buck3_ramp_enable; - s2mps11->buck4_ramp = pdata->buck4_ramp_enable; - - ramp_enable = (s2mps11->buck2_ramp << 3) | (s2mps11->buck3_ramp << 2) | - (s2mps11->buck4_ramp << 1) | s2mps11->buck6_ramp ; - - if (ramp_enable) { - if (s2mps11->buck2_ramp) - ramp_reg |= get_ramp_delay(s2mps11->ramp_delay2) << 6; - if (s2mps11->buck3_ramp || s2mps11->buck4_ramp) - ramp_reg |= get_ramp_delay(s2mps11->ramp_delay34) << 4; - sec_reg_write(iodev, S2MPS11_REG_RAMP, ramp_reg | ramp_enable); + if (!iodev->dev->of_node) { + if (pdata) { + goto common_reg; + } else { + dev_err(pdev->dev.parent, + "Platform data or DT node not supplied\n"); + return -ENODEV; + } } - ramp_reg &= 0x00; - ramp_reg |= get_ramp_delay(s2mps11->ramp_delay5) << 6; - ramp_reg |= get_ramp_delay(s2mps11->ramp_delay16) << 4; - ramp_reg |= get_ramp_delay(s2mps11->ramp_delay7810) << 2; - ramp_reg |= get_ramp_delay(s2mps11->ramp_delay9); - sec_reg_write(iodev, S2MPS11_REG_RAMP_BUCK, ramp_reg); + for (i = 0; i < S2MPS11_REGULATOR_CNT; i++) + rdata[i].name = regulators[i].name; + reg_np = of_find_node_by_name(iodev->dev->of_node, "regulators"); + if (!reg_np) { + dev_err(&pdev->dev, "could not find regulators sub-node\n"); + return -EINVAL; + } + + of_regulator_match(&pdev->dev, reg_np, rdata, S2MPS11_REGULATOR_MAX); + +common_reg: + platform_set_drvdata(pdev, s2mps11); + + config.dev = &pdev->dev; + config.regmap = iodev->regmap; + config.driver_data = s2mps11; for (i = 0; i < S2MPS11_REGULATOR_MAX; i++) { - - config.dev = &pdev->dev; - config.regmap = iodev->regmap; - config.init_data = pdata->regulators[i].initdata; - config.driver_data = s2mps11; + if (!reg_np) { + config.init_data = pdata->regulators[i].initdata; + } else { + config.init_data = rdata[i].init_data; + config.of_node = rdata[i].of_node; + } s2mps11->rdev[i] = regulator_register(®ulators[i], &config); if (IS_ERR(s2mps11->rdev[i])) { diff --git a/drivers/regulator/ti-abb-regulator.c b/drivers/regulator/ti-abb-regulator.c index 3753ed05e719..d8e3e1262bc2 100644 --- a/drivers/regulator/ti-abb-regulator.c +++ b/drivers/regulator/ti-abb-regulator.c @@ -717,11 +717,6 @@ static int ti_abb_probe(struct platform_device *pdev) /* Map ABB resources */ pname = "base-address"; res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); - if (!res) { - dev_err(dev, "Missing '%s' IO resource\n", pname); - ret = -ENODEV; - goto err; - } abb->base = devm_ioremap_resource(dev, res); if (IS_ERR(abb->base)) { ret = PTR_ERR(abb->base); @@ -770,11 +765,6 @@ static int ti_abb_probe(struct platform_device *pdev) pname = "ldo-address"; res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); - if (!res) { - dev_dbg(dev, "Missing '%s' IO resource\n", pname); - ret = -ENODEV; - goto skip_opt; - } abb->ldo_base = devm_ioremap_resource(dev, res); if (IS_ERR(abb->ldo_base)) { ret = PTR_ERR(abb->ldo_base); diff --git a/drivers/regulator/tps51632-regulator.c b/drivers/regulator/tps51632-regulator.c index 6e67be75ea1b..9392a7ca3d2d 100644 --- a/drivers/regulator/tps51632-regulator.c +++ b/drivers/regulator/tps51632-regulator.c @@ -275,7 +275,7 @@ static int tps51632_probe(struct i2c_client *client, } } - pdata = client->dev.platform_data; + pdata = dev_get_platdata(&client->dev); if (!pdata && client->dev.of_node) pdata = of_get_tps51632_platform_data(&client->dev); if (!pdata) { diff --git a/drivers/regulator/tps62360-regulator.c b/drivers/regulator/tps62360-regulator.c index a490d5b749b2..0b7ebb1ebf85 100644 --- a/drivers/regulator/tps62360-regulator.c +++ b/drivers/regulator/tps62360-regulator.c @@ -350,7 +350,7 @@ static int tps62360_probe(struct i2c_client *client, int i; int chip_id; - pdata = client->dev.platform_data; + pdata = dev_get_platdata(&client->dev); if (client->dev.of_node) { const struct of_device_id *match; diff --git a/drivers/regulator/tps65023-regulator.c b/drivers/regulator/tps65023-regulator.c index 9d053e23e9eb..a15263d4bdff 100644 --- a/drivers/regulator/tps65023-regulator.c +++ b/drivers/regulator/tps65023-regulator.c @@ -218,7 +218,7 @@ static int tps_65023_probe(struct i2c_client *client, * init_data points to array of regulator_init structures * coming from the board-evm file. */ - init_data = client->dev.platform_data; + init_data = dev_get_platdata(&client->dev); if (!init_data) return -EIO; diff --git a/drivers/regulator/tps65217-regulator.c b/drivers/regulator/tps65217-regulator.c index 2df4616621f5..90861d68a0b0 100644 --- a/drivers/regulator/tps65217-regulator.c +++ b/drivers/regulator/tps65217-regulator.c @@ -27,7 +27,7 @@ #include #include -#define TPS65217_REGULATOR(_name, _id, _ops, _n, _vr, _vm, _em, _t) \ +#define TPS65217_REGULATOR(_name, _id, _ops, _n, _vr, _vm, _em, _t, _lr, _nlr) \ { \ .name = _name, \ .id = _id, \ @@ -40,17 +40,10 @@ .enable_reg = TPS65217_REG_ENABLE, \ .enable_mask = _em, \ .volt_table = _t, \ + .linear_ranges = _lr, \ + .n_linear_ranges = _nlr, \ } \ -#define TPS65217_INFO(_nm, _min, _max, _f1, _f2) \ - { \ - .name = _nm, \ - .min_uV = _min, \ - .max_uV = _max, \ - .vsel_to_uv = _f1, \ - .uv_to_vsel = _f2, \ - } - static const unsigned int LDO1_VSEL_table[] = { 1000000, 1100000, 1200000, 1250000, 1300000, 1350000, 1400000, 1500000, @@ -58,88 +51,26 @@ static const unsigned int LDO1_VSEL_table[] = { 2800000, 3000000, 3100000, 3300000, }; -static int tps65217_vsel_to_uv1(unsigned int vsel) -{ - int uV = 0; +static const struct regulator_linear_range tps65217_uv1_ranges[] = { + { .min_uV = 900000, .max_uV = 1500000, .min_sel = 0, .max_sel = 24, + .uV_step = 25000 }, + { .min_uV = 1550000, .max_uV = 1800000, .min_sel = 25, .max_sel = 30, + .uV_step = 50000 }, + { .min_uV = 1850000, .max_uV = 2900000, .min_sel = 31, .max_sel = 52, + .uV_step = 50000 }, + { .min_uV = 3000000, .max_uV = 3200000, .min_sel = 53, .max_sel = 55, + .uV_step = 100000 }, + { .min_uV = 3300000, .max_uV = 3300000, .min_sel = 56, .max_sel = 62, + .uV_step = 0 }, +}; - if (vsel > 63) - return -EINVAL; - - if (vsel <= 24) - uV = vsel * 25000 + 900000; - else if (vsel <= 52) - uV = (vsel - 24) * 50000 + 1500000; - else if (vsel < 56) - uV = (vsel - 52) * 100000 + 2900000; - else - uV = 3300000; - - return uV; -} - -static int tps65217_uv_to_vsel1(int uV, unsigned int *vsel) -{ - if (uV < 0 || uV > 3300000) - return -EINVAL; - - if (uV <= 1500000) - *vsel = DIV_ROUND_UP(uV - 900000, 25000); - else if (uV <= 2900000) - *vsel = 24 + DIV_ROUND_UP(uV - 1500000, 50000); - else if (uV < 3300000) - *vsel = 52 + DIV_ROUND_UP(uV - 2900000, 100000); - else - *vsel = 56; - - return 0; -} - -static int tps65217_vsel_to_uv2(unsigned int vsel) -{ - int uV = 0; - - if (vsel > 31) - return -EINVAL; - - if (vsel <= 8) - uV = vsel * 50000 + 1500000; - else if (vsel <= 13) - uV = (vsel - 8) * 100000 + 1900000; - else - uV = (vsel - 13) * 50000 + 2400000; - - return uV; -} - -static int tps65217_uv_to_vsel2(int uV, unsigned int *vsel) -{ - if (uV < 0 || uV > 3300000) - return -EINVAL; - - if (uV <= 1900000) - *vsel = DIV_ROUND_UP(uV - 1500000, 50000); - else if (uV <= 2400000) - *vsel = 8 + DIV_ROUND_UP(uV - 1900000, 100000); - else - *vsel = 13 + DIV_ROUND_UP(uV - 2400000, 50000); - - return 0; -} - -static struct tps_info tps65217_pmic_regs[] = { - TPS65217_INFO("DCDC1", 900000, 1800000, tps65217_vsel_to_uv1, - tps65217_uv_to_vsel1), - TPS65217_INFO("DCDC2", 900000, 3300000, tps65217_vsel_to_uv1, - tps65217_uv_to_vsel1), - TPS65217_INFO("DCDC3", 900000, 1500000, tps65217_vsel_to_uv1, - tps65217_uv_to_vsel1), - TPS65217_INFO("LDO1", 1000000, 3300000, NULL, NULL), - TPS65217_INFO("LDO2", 900000, 3300000, tps65217_vsel_to_uv1, - tps65217_uv_to_vsel1), - TPS65217_INFO("LDO3", 1800000, 3300000, tps65217_vsel_to_uv2, - tps65217_uv_to_vsel2), - TPS65217_INFO("LDO4", 1800000, 3300000, tps65217_vsel_to_uv2, - tps65217_uv_to_vsel2), +static const struct regulator_linear_range tps65217_uv2_ranges[] = { + { .min_uV = 1500000, .max_uV = 1900000, .min_sel = 0, .max_sel = 8, + .uV_step = 50000 }, + { .min_uV = 2000000, .max_uV = 2400000, .min_sel = 9, .max_sel = 13, + .uV_step = 100000 }, + { .min_uV = 2450000, .max_uV = 3300000, .min_sel = 14, .max_sel = 31, + .uV_step = 50000 }, }; static int tps65217_pmic_enable(struct regulator_dev *dev) @@ -192,49 +123,6 @@ static int tps65217_pmic_set_voltage_sel(struct regulator_dev *dev, return ret; } -static int tps65217_pmic_map_voltage(struct regulator_dev *dev, - int min_uV, int max_uV) -{ - - struct tps65217 *tps = rdev_get_drvdata(dev); - unsigned int sel, rid = rdev_get_id(dev); - int ret; - - /* LDO1 uses regulator_map_voltage_iterate() */ - if (rid == TPS65217_LDO_1) - return -EINVAL; - - if (rid < TPS65217_DCDC_1 || rid > TPS65217_LDO_4) - return -EINVAL; - - if (min_uV < tps->info[rid]->min_uV) - min_uV = tps->info[rid]->min_uV; - - if (max_uV < tps->info[rid]->min_uV || min_uV > tps->info[rid]->max_uV) - return -EINVAL; - - ret = tps->info[rid]->uv_to_vsel(min_uV, &sel); - if (ret) - return ret; - - return sel; -} - -static int tps65217_pmic_list_voltage(struct regulator_dev *dev, - unsigned selector) -{ - struct tps65217 *tps = rdev_get_drvdata(dev); - unsigned int rid = rdev_get_id(dev); - - if (rid < TPS65217_DCDC_1 || rid > TPS65217_LDO_4) - return -EINVAL; - - if (selector >= dev->desc->n_voltages) - return -EINVAL; - - return tps->info[rid]->vsel_to_uv(selector); -} - /* Operations permitted on DCDCx, LDO2, LDO3 and LDO4 */ static struct regulator_ops tps65217_pmic_ops = { .is_enabled = regulator_is_enabled_regmap, @@ -242,8 +130,8 @@ static struct regulator_ops tps65217_pmic_ops = { .disable = tps65217_pmic_disable, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = tps65217_pmic_set_voltage_sel, - .list_voltage = tps65217_pmic_list_voltage, - .map_voltage = tps65217_pmic_map_voltage, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, }; /* Operations permitted on LDO1 */ @@ -259,27 +147,33 @@ static struct regulator_ops tps65217_pmic_ldo1_ops = { static const struct regulator_desc regulators[] = { TPS65217_REGULATOR("DCDC1", TPS65217_DCDC_1, tps65217_pmic_ops, 64, TPS65217_REG_DEFDCDC1, TPS65217_DEFDCDCX_DCDC_MASK, - TPS65217_ENABLE_DC1_EN, NULL), + TPS65217_ENABLE_DC1_EN, NULL, tps65217_uv1_ranges, + 2), /* DCDC1 voltage range: 900000 ~ 1800000 */ TPS65217_REGULATOR("DCDC2", TPS65217_DCDC_2, tps65217_pmic_ops, 64, TPS65217_REG_DEFDCDC2, TPS65217_DEFDCDCX_DCDC_MASK, - TPS65217_ENABLE_DC2_EN, NULL), + TPS65217_ENABLE_DC2_EN, NULL, tps65217_uv1_ranges, + ARRAY_SIZE(tps65217_uv1_ranges)), TPS65217_REGULATOR("DCDC3", TPS65217_DCDC_3, tps65217_pmic_ops, 64, TPS65217_REG_DEFDCDC3, TPS65217_DEFDCDCX_DCDC_MASK, - TPS65217_ENABLE_DC3_EN, NULL), + TPS65217_ENABLE_DC3_EN, NULL, tps65217_uv1_ranges, + 1), /* DCDC3 voltage range: 900000 ~ 1500000 */ TPS65217_REGULATOR("LDO1", TPS65217_LDO_1, tps65217_pmic_ldo1_ops, 16, TPS65217_REG_DEFLDO1, TPS65217_DEFLDO1_LDO1_MASK, - TPS65217_ENABLE_LDO1_EN, LDO1_VSEL_table), + TPS65217_ENABLE_LDO1_EN, LDO1_VSEL_table, NULL, 0), TPS65217_REGULATOR("LDO2", TPS65217_LDO_2, tps65217_pmic_ops, 64, TPS65217_REG_DEFLDO2, TPS65217_DEFLDO2_LDO2_MASK, - TPS65217_ENABLE_LDO2_EN, NULL), + TPS65217_ENABLE_LDO2_EN, NULL, tps65217_uv1_ranges, + ARRAY_SIZE(tps65217_uv1_ranges)), TPS65217_REGULATOR("LDO3", TPS65217_LDO_3, tps65217_pmic_ops, 32, TPS65217_REG_DEFLS1, TPS65217_DEFLDO3_LDO3_MASK, TPS65217_ENABLE_LS1_EN | TPS65217_DEFLDO3_LDO3_EN, - NULL), + NULL, tps65217_uv2_ranges, + ARRAY_SIZE(tps65217_uv2_ranges)), TPS65217_REGULATOR("LDO4", TPS65217_LDO_4, tps65217_pmic_ops, 32, TPS65217_REG_DEFLS2, TPS65217_DEFLDO4_LDO4_MASK, TPS65217_ENABLE_LS2_EN | TPS65217_DEFLDO4_LDO4_EN, - NULL), + NULL, tps65217_uv2_ranges, + ARRAY_SIZE(tps65217_uv2_ranges)), }; #ifdef CONFIG_OF @@ -368,8 +262,6 @@ static int tps65217_regulator_probe(struct platform_device *pdev) continue; /* Register the regulators */ - tps->info[i] = &tps65217_pmic_regs[i]; - config.dev = tps->dev; config.init_data = reg_data; config.driver_data = tps; diff --git a/drivers/regulator/tps6524x-regulator.c b/drivers/regulator/tps6524x-regulator.c index 1094393155ed..62e8d28beabd 100644 --- a/drivers/regulator/tps6524x-regulator.c +++ b/drivers/regulator/tps6524x-regulator.c @@ -601,7 +601,7 @@ static int pmic_probe(struct spi_device *spi) struct regulator_config config = { }; int ret = 0, i; - init_data = dev->platform_data; + init_data = dev_get_platdata(dev); if (!init_data) { dev_err(dev, "could not find regulator platform data\n"); return -EINVAL; diff --git a/drivers/regulator/tps65912-regulator.c b/drivers/regulator/tps65912-regulator.c index 17e994e47dc1..281e52ac64ba 100644 --- a/drivers/regulator/tps65912-regulator.c +++ b/drivers/regulator/tps65912-regulator.c @@ -118,6 +118,15 @@ struct tps65912_reg { int eco_reg; }; +static const struct regulator_linear_range tps65912_ldo_ranges[] = { + { .min_uV = 800000, .max_uV = 1600000, .min_sel = 0, .max_sel = 32, + .uV_step = 25000 }, + { .min_uV = 1650000, .max_uV = 3000000, .min_sel = 33, .max_sel = 60, + .uV_step = 50000 }, + { .min_uV = 3100000, .max_uV = 3300000, .min_sel = 61, .max_sel = 63, + .uV_step = 100000 }, +}; + static int tps65912_get_range(struct tps65912_reg *pmic, int id) { struct tps65912 *mfd = pmic->mfd; @@ -184,20 +193,6 @@ static unsigned long tps65912_vsel_to_uv_range3(u8 vsel) return uv; } -static unsigned long tps65912_vsel_to_uv_ldo(u8 vsel) -{ - unsigned long uv = 0; - - if (vsel <= 32) - uv = ((vsel * 25000) + 800000); - else if (vsel > 32 && vsel <= 60) - uv = (((vsel - 32) * 50000) + 1600000); - else if (vsel > 60) - uv = (((vsel - 60) * 100000) + 3000000); - - return uv; -} - static int tps65912_get_ctrl_register(int id) { if (id >= TPS65912_REG_DCDC1 && id <= TPS65912_REG_LDO4) @@ -376,9 +371,6 @@ static int tps65912_list_voltage(struct regulator_dev *dev, unsigned selector) struct tps65912_reg *pmic = rdev_get_drvdata(dev); int range, voltage = 0, id = rdev_get_id(dev); - if (id >= TPS65912_REG_LDO1 && id <= TPS65912_REG_LDO10) - return tps65912_vsel_to_uv_ldo(selector); - if (id > TPS65912_REG_DCDC4) return -EINVAL; @@ -456,7 +448,8 @@ static struct regulator_ops tps65912_ops_ldo = { .disable = tps65912_reg_disable, .get_voltage_sel = tps65912_get_voltage_sel, .set_voltage_sel = tps65912_set_voltage_sel, - .list_voltage = tps65912_list_voltage, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, }; static int tps65912_probe(struct platform_device *pdev) @@ -495,8 +488,14 @@ static int tps65912_probe(struct platform_device *pdev) pmic->desc[i].name = info->name; pmic->desc[i].id = i; pmic->desc[i].n_voltages = 64; - pmic->desc[i].ops = (i > TPS65912_REG_DCDC4 ? - &tps65912_ops_ldo : &tps65912_ops_dcdc); + if (i > TPS65912_REG_DCDC4) { + pmic->desc[i].ops = &tps65912_ops_ldo; + pmic->desc[i].linear_ranges = tps65912_ldo_ranges; + pmic->desc[i].n_linear_ranges = + ARRAY_SIZE(tps65912_ldo_ranges); + } else { + pmic->desc[i].ops = &tps65912_ops_dcdc; + } pmic->desc[i].type = REGULATOR_VOLTAGE; pmic->desc[i].owner = THIS_MODULE; range = tps65912_get_range(pmic, i); diff --git a/drivers/regulator/twl-regulator.c b/drivers/regulator/twl-regulator.c index 93bc4f456da4..78aae4cbb004 100644 --- a/drivers/regulator/twl-regulator.c +++ b/drivers/regulator/twl-regulator.c @@ -1108,7 +1108,7 @@ static int twlreg_probe(struct platform_device *pdev) drvdata = NULL; } else { id = pdev->id; - initdata = pdev->dev.platform_data; + initdata = dev_get_platdata(&pdev->dev); for (i = 0, template = NULL; i < ARRAY_SIZE(twl_of_match); i++) { template = twl_of_match[i].data; if (template && template->desc.id == id) diff --git a/drivers/regulator/userspace-consumer.c b/drivers/regulator/userspace-consumer.c index a7c8deb5f28f..765acc11c9c8 100644 --- a/drivers/regulator/userspace-consumer.c +++ b/drivers/regulator/userspace-consumer.c @@ -111,7 +111,7 @@ static int regulator_userspace_consumer_probe(struct platform_device *pdev) struct userspace_consumer_data *drvdata; int ret; - pdata = pdev->dev.platform_data; + pdata = dev_get_platdata(&pdev->dev); if (!pdata) return -EINVAL; diff --git a/drivers/regulator/virtual.c b/drivers/regulator/virtual.c index a9d4284ea007..f53e78b9a84e 100644 --- a/drivers/regulator/virtual.c +++ b/drivers/regulator/virtual.c @@ -287,7 +287,7 @@ static const struct attribute_group regulator_virtual_attr_group = { static int regulator_virtual_probe(struct platform_device *pdev) { - char *reg_id = pdev->dev.platform_data; + char *reg_id = dev_get_platdata(&pdev->dev); struct virtual_consumer_data *drvdata; int ret; diff --git a/drivers/regulator/wm831x-dcdc.c b/drivers/regulator/wm831x-dcdc.c index 46938cf162ad..11861cb861df 100644 --- a/drivers/regulator/wm831x-dcdc.c +++ b/drivers/regulator/wm831x-dcdc.c @@ -451,7 +451,7 @@ static void wm831x_buckv_dvs_init(struct wm831x_dcdc *dcdc, static int wm831x_buckv_probe(struct platform_device *pdev) { struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent); - struct wm831x_pdata *pdata = wm831x->dev->platform_data; + struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev); struct regulator_config config = { }; int id; struct wm831x_dcdc *dcdc; @@ -624,7 +624,7 @@ static struct regulator_ops wm831x_buckp_ops = { static int wm831x_buckp_probe(struct platform_device *pdev) { struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent); - struct wm831x_pdata *pdata = wm831x->dev->platform_data; + struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev); struct regulator_config config = { }; int id; struct wm831x_dcdc *dcdc; @@ -770,7 +770,7 @@ static struct regulator_ops wm831x_boostp_ops = { static int wm831x_boostp_probe(struct platform_device *pdev) { struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent); - struct wm831x_pdata *pdata = wm831x->dev->platform_data; + struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev); struct regulator_config config = { }; int id = pdev->id % ARRAY_SIZE(pdata->dcdc); struct wm831x_dcdc *dcdc; @@ -880,7 +880,7 @@ static struct regulator_ops wm831x_epe_ops = { static int wm831x_epe_probe(struct platform_device *pdev) { struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent); - struct wm831x_pdata *pdata = wm831x->dev->platform_data; + struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev); struct regulator_config config = { }; int id = pdev->id % ARRAY_SIZE(pdata->epe); struct wm831x_dcdc *dcdc; diff --git a/drivers/regulator/wm831x-isink.c b/drivers/regulator/wm831x-isink.c index 16ebdf94d0a0..4eb373de1fac 100644 --- a/drivers/regulator/wm831x-isink.c +++ b/drivers/regulator/wm831x-isink.c @@ -151,7 +151,7 @@ static irqreturn_t wm831x_isink_irq(int irq, void *data) static int wm831x_isink_probe(struct platform_device *pdev) { struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent); - struct wm831x_pdata *pdata = wm831x->dev->platform_data; + struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev); struct wm831x_isink *isink; int id = pdev->id % ARRAY_SIZE(pdata->isink); struct regulator_config config = { }; diff --git a/drivers/regulator/wm831x-ldo.c b/drivers/regulator/wm831x-ldo.c index 9ff883f80878..1432b26ef2e9 100644 --- a/drivers/regulator/wm831x-ldo.c +++ b/drivers/regulator/wm831x-ldo.c @@ -62,41 +62,12 @@ static irqreturn_t wm831x_ldo_uv_irq(int irq, void *data) * General purpose LDOs */ -#define WM831X_GP_LDO_SELECTOR_LOW 0xe -#define WM831X_GP_LDO_MAX_SELECTOR 0x1f - -static int wm831x_gp_ldo_list_voltage(struct regulator_dev *rdev, - unsigned int selector) -{ - /* 0.9-1.6V in 50mV steps */ - if (selector <= WM831X_GP_LDO_SELECTOR_LOW) - return 900000 + (selector * 50000); - /* 1.7-3.3V in 100mV steps */ - if (selector <= WM831X_GP_LDO_MAX_SELECTOR) - return 1600000 + ((selector - WM831X_GP_LDO_SELECTOR_LOW) - * 100000); - return -EINVAL; -} - -static int wm831x_gp_ldo_map_voltage(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int volt, vsel; - - if (min_uV < 900000) - vsel = 0; - else if (min_uV < 1700000) - vsel = ((min_uV - 900000) / 50000); - else - vsel = ((min_uV - 1700000) / 100000) - + WM831X_GP_LDO_SELECTOR_LOW + 1; - - volt = wm831x_gp_ldo_list_voltage(rdev, vsel); - if (volt < min_uV || volt > max_uV) - return -EINVAL; - - return vsel; -} +static const struct regulator_linear_range wm831x_gp_ldo_ranges[] = { + { .min_uV = 900000, .max_uV = 1650000, .min_sel = 0, .max_sel = 14, + .uV_step = 50000 }, + { .min_uV = 1700000, .max_uV = 3300000, .min_sel = 15, .max_sel = 31, + .uV_step = 100000 }, +}; static int wm831x_gp_ldo_set_suspend_voltage(struct regulator_dev *rdev, int uV) @@ -105,7 +76,7 @@ static int wm831x_gp_ldo_set_suspend_voltage(struct regulator_dev *rdev, struct wm831x *wm831x = ldo->wm831x; int sel, reg = ldo->base + WM831X_LDO_SLEEP_CONTROL; - sel = wm831x_gp_ldo_map_voltage(rdev, uV, uV); + sel = regulator_map_voltage_linear_range(rdev, uV, uV); if (sel < 0) return sel; @@ -230,8 +201,8 @@ static unsigned int wm831x_gp_ldo_get_optimum_mode(struct regulator_dev *rdev, static struct regulator_ops wm831x_gp_ldo_ops = { - .list_voltage = wm831x_gp_ldo_list_voltage, - .map_voltage = wm831x_gp_ldo_map_voltage, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, .set_suspend_voltage = wm831x_gp_ldo_set_suspend_voltage, @@ -250,7 +221,7 @@ static struct regulator_ops wm831x_gp_ldo_ops = { static int wm831x_gp_ldo_probe(struct platform_device *pdev) { struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent); - struct wm831x_pdata *pdata = wm831x->dev->platform_data; + struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev); struct regulator_config config = { }; int id; struct wm831x_ldo *ldo; @@ -290,7 +261,7 @@ static int wm831x_gp_ldo_probe(struct platform_device *pdev) ldo->desc.id = id; ldo->desc.type = REGULATOR_VOLTAGE; - ldo->desc.n_voltages = WM831X_GP_LDO_MAX_SELECTOR + 1; + ldo->desc.n_voltages = 32; ldo->desc.ops = &wm831x_gp_ldo_ops; ldo->desc.owner = THIS_MODULE; ldo->desc.vsel_reg = ldo->base + WM831X_LDO_ON_CONTROL; @@ -299,6 +270,8 @@ static int wm831x_gp_ldo_probe(struct platform_device *pdev) ldo->desc.enable_mask = 1 << id; ldo->desc.bypass_reg = ldo->base; ldo->desc.bypass_mask = WM831X_LDO1_SWI; + ldo->desc.linear_ranges = wm831x_gp_ldo_ranges; + ldo->desc.n_linear_ranges = ARRAY_SIZE(wm831x_gp_ldo_ranges); config.dev = pdev->dev.parent; if (pdata) @@ -358,43 +331,12 @@ static struct platform_driver wm831x_gp_ldo_driver = { * Analogue LDOs */ - -#define WM831X_ALDO_SELECTOR_LOW 0xc -#define WM831X_ALDO_MAX_SELECTOR 0x1f - -static int wm831x_aldo_list_voltage(struct regulator_dev *rdev, - unsigned int selector) -{ - /* 1-1.6V in 50mV steps */ - if (selector <= WM831X_ALDO_SELECTOR_LOW) - return 1000000 + (selector * 50000); - /* 1.7-3.5V in 100mV steps */ - if (selector <= WM831X_ALDO_MAX_SELECTOR) - return 1600000 + ((selector - WM831X_ALDO_SELECTOR_LOW) - * 100000); - return -EINVAL; -} - -static int wm831x_aldo_map_voltage(struct regulator_dev *rdev, - int min_uV, int max_uV) -{ - int volt, vsel; - - if (min_uV < 1000000) - vsel = 0; - else if (min_uV < 1700000) - vsel = ((min_uV - 1000000) / 50000); - else - vsel = ((min_uV - 1700000) / 100000) - + WM831X_ALDO_SELECTOR_LOW + 1; - - volt = wm831x_aldo_list_voltage(rdev, vsel); - if (volt < min_uV || volt > max_uV) - return -EINVAL; - - return vsel; - -} +static const struct regulator_linear_range wm831x_aldo_ranges[] = { + { .min_uV = 1000000, .max_uV = 1650000, .min_sel = 0, .max_sel = 12, + .uV_step = 50000 }, + { .min_uV = 1700000, .max_uV = 3500000, .min_sel = 13, .max_sel = 31, + .uV_step = 100000 }, +}; static int wm831x_aldo_set_suspend_voltage(struct regulator_dev *rdev, int uV) @@ -403,7 +345,7 @@ static int wm831x_aldo_set_suspend_voltage(struct regulator_dev *rdev, struct wm831x *wm831x = ldo->wm831x; int sel, reg = ldo->base + WM831X_LDO_SLEEP_CONTROL; - sel = wm831x_aldo_map_voltage(rdev, uV, uV); + sel = regulator_map_voltage_linear_range(rdev, uV, uV); if (sel < 0) return sel; @@ -486,8 +428,8 @@ static int wm831x_aldo_get_status(struct regulator_dev *rdev) } static struct regulator_ops wm831x_aldo_ops = { - .list_voltage = wm831x_aldo_list_voltage, - .map_voltage = wm831x_aldo_map_voltage, + .list_voltage = regulator_list_voltage_linear_range, + .map_voltage = regulator_map_voltage_linear_range, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, .set_suspend_voltage = wm831x_aldo_set_suspend_voltage, @@ -505,7 +447,7 @@ static struct regulator_ops wm831x_aldo_ops = { static int wm831x_aldo_probe(struct platform_device *pdev) { struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent); - struct wm831x_pdata *pdata = wm831x->dev->platform_data; + struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev); struct regulator_config config = { }; int id; struct wm831x_ldo *ldo; @@ -545,7 +487,9 @@ static int wm831x_aldo_probe(struct platform_device *pdev) ldo->desc.id = id; ldo->desc.type = REGULATOR_VOLTAGE; - ldo->desc.n_voltages = WM831X_ALDO_MAX_SELECTOR + 1; + ldo->desc.n_voltages = 32; + ldo->desc.linear_ranges = wm831x_aldo_ranges; + ldo->desc.n_linear_ranges = ARRAY_SIZE(wm831x_aldo_ranges); ldo->desc.ops = &wm831x_aldo_ops; ldo->desc.owner = THIS_MODULE; ldo->desc.vsel_reg = ldo->base + WM831X_LDO_ON_CONTROL; @@ -661,7 +605,7 @@ static struct regulator_ops wm831x_alive_ldo_ops = { static int wm831x_alive_ldo_probe(struct platform_device *pdev) { struct wm831x *wm831x = dev_get_drvdata(pdev->dev.parent); - struct wm831x_pdata *pdata = wm831x->dev->platform_data; + struct wm831x_pdata *pdata = dev_get_platdata(wm831x->dev); struct regulator_config config = { }; int id; struct wm831x_ldo *ldo; diff --git a/drivers/regulator/wm8350-regulator.c b/drivers/regulator/wm8350-regulator.c index 7f0fa22ef2aa..835b5f0f344e 100644 --- a/drivers/regulator/wm8350-regulator.c +++ b/drivers/regulator/wm8350-regulator.c @@ -542,41 +542,12 @@ static int wm8350_dcdc_set_suspend_mode(struct regulator_dev *rdev, return 0; } -static int wm8350_ldo_list_voltage(struct regulator_dev *rdev, - unsigned selector) -{ - if (selector > WM8350_LDO1_VSEL_MASK) - return -EINVAL; - - if (selector < 16) - return (selector * 50000) + 900000; - else - return ((selector - 16) * 100000) + 1800000; -} - -static int wm8350_ldo_map_voltage(struct regulator_dev *rdev, int min_uV, - int max_uV) -{ - int volt, sel; - int min_mV = min_uV / 1000; - int max_mV = max_uV / 1000; - - if (min_mV < 900 || min_mV > 3300) - return -EINVAL; - if (max_mV < 900 || max_mV > 3300) - return -EINVAL; - - if (min_mV < 1800) /* step size is 50mV < 1800mV */ - sel = DIV_ROUND_UP(min_uV - 900, 50); - else /* step size is 100mV > 1800mV */ - sel = DIV_ROUND_UP(min_uV - 1800, 100) + 16; - - volt = wm8350_ldo_list_voltage(rdev, sel); - if (volt < min_uV || volt > max_uV) - return -EINVAL; - - return sel; -} +static const struct regulator_linear_range wm8350_ldo_ranges[] = { + { .min_uV = 900000, .max_uV = 1750000, .min_sel = 0, .max_sel = 15, + .uV_step = 50000 }, + { .min_uV = 1800000, .max_uV = 3300000, .min_sel = 16, .max_sel = 31, + .uV_step = 100000 }, +}; static int wm8350_ldo_set_suspend_voltage(struct regulator_dev *rdev, int uV) { @@ -603,7 +574,7 @@ static int wm8350_ldo_set_suspend_voltage(struct regulator_dev *rdev, int uV) return -EINVAL; } - sel = wm8350_ldo_map_voltage(rdev, uV, uV); + sel = regulator_map_voltage_linear_range(rdev, uV, uV); if (sel < 0) return -EINVAL; @@ -998,10 +969,10 @@ static struct regulator_ops wm8350_dcdc2_5_ops = { }; static struct regulator_ops wm8350_ldo_ops = { - .map_voltage = wm8350_ldo_map_voltage, + .map_voltage = regulator_map_voltage_linear_range, .set_voltage_sel = regulator_set_voltage_sel_regmap, .get_voltage_sel = regulator_get_voltage_sel_regmap, - .list_voltage = wm8350_ldo_list_voltage, + .list_voltage = regulator_list_voltage_linear_range, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, .is_enabled = regulator_is_enabled_regmap, @@ -1108,6 +1079,8 @@ static const struct regulator_desc wm8350_reg[NUM_WM8350_REGULATORS] = { .irq = WM8350_IRQ_UV_LDO1, .type = REGULATOR_VOLTAGE, .n_voltages = WM8350_LDO1_VSEL_MASK + 1, + .linear_ranges = wm8350_ldo_ranges, + .n_linear_ranges = ARRAY_SIZE(wm8350_ldo_ranges), .vsel_reg = WM8350_LDO1_CONTROL, .vsel_mask = WM8350_LDO1_VSEL_MASK, .enable_reg = WM8350_DCDC_LDO_REQUESTED, @@ -1121,6 +1094,8 @@ static const struct regulator_desc wm8350_reg[NUM_WM8350_REGULATORS] = { .irq = WM8350_IRQ_UV_LDO2, .type = REGULATOR_VOLTAGE, .n_voltages = WM8350_LDO2_VSEL_MASK + 1, + .linear_ranges = wm8350_ldo_ranges, + .n_linear_ranges = ARRAY_SIZE(wm8350_ldo_ranges), .vsel_reg = WM8350_LDO2_CONTROL, .vsel_mask = WM8350_LDO2_VSEL_MASK, .enable_reg = WM8350_DCDC_LDO_REQUESTED, @@ -1134,6 +1109,8 @@ static const struct regulator_desc wm8350_reg[NUM_WM8350_REGULATORS] = { .irq = WM8350_IRQ_UV_LDO3, .type = REGULATOR_VOLTAGE, .n_voltages = WM8350_LDO3_VSEL_MASK + 1, + .linear_ranges = wm8350_ldo_ranges, + .n_linear_ranges = ARRAY_SIZE(wm8350_ldo_ranges), .vsel_reg = WM8350_LDO3_CONTROL, .vsel_mask = WM8350_LDO3_VSEL_MASK, .enable_reg = WM8350_DCDC_LDO_REQUESTED, @@ -1147,6 +1124,8 @@ static const struct regulator_desc wm8350_reg[NUM_WM8350_REGULATORS] = { .irq = WM8350_IRQ_UV_LDO4, .type = REGULATOR_VOLTAGE, .n_voltages = WM8350_LDO4_VSEL_MASK + 1, + .linear_ranges = wm8350_ldo_ranges, + .n_linear_ranges = ARRAY_SIZE(wm8350_ldo_ranges), .vsel_reg = WM8350_LDO4_CONTROL, .vsel_mask = WM8350_LDO4_VSEL_MASK, .enable_reg = WM8350_DCDC_LDO_REQUESTED, @@ -1222,7 +1201,7 @@ static int wm8350_regulator_probe(struct platform_device *pdev) } config.dev = &pdev->dev; - config.init_data = pdev->dev.platform_data; + config.init_data = dev_get_platdata(&pdev->dev); config.driver_data = dev_get_drvdata(&pdev->dev); config.regmap = wm8350->regmap; diff --git a/drivers/regulator/wm8400-regulator.c b/drivers/regulator/wm8400-regulator.c index a09f03ee5506..58f51bec13f2 100644 --- a/drivers/regulator/wm8400-regulator.c +++ b/drivers/regulator/wm8400-regulator.c @@ -19,47 +19,21 @@ #include #include -static int wm8400_ldo_list_voltage(struct regulator_dev *dev, - unsigned selector) -{ - if (selector > WM8400_LDO1_VSEL_MASK) - return -EINVAL; - - if (selector < 15) - return 900000 + (selector * 50000); - else - return 1700000 + ((selector - 15) * 100000); -} - -static int wm8400_ldo_map_voltage(struct regulator_dev *dev, - int min_uV, int max_uV) -{ - u16 val; - int volt; - - if (min_uV < 900000 || min_uV > 3300000) - return -EINVAL; - - if (min_uV < 1700000) /* Steps of 50mV from 900mV; */ - val = DIV_ROUND_UP(min_uV - 900000, 50000); - else /* Steps of 100mV from 1700mV */ - val = DIV_ROUND_UP(min_uV - 1700000, 100000) + 15; - - volt = wm8400_ldo_list_voltage(dev, val); - if (volt < min_uV || volt > max_uV) - return -EINVAL; - - return val; -} +static const struct regulator_linear_range wm8400_ldo_ranges[] = { + { .min_uV = 900000, .max_uV = 1600000, .min_sel = 0, .max_sel = 14, + .uV_step = 50000 }, + { .min_uV = 1700000, .max_uV = 3300000, .min_sel = 15, .max_sel = 31, + .uV_step = 100000 }, +}; static struct regulator_ops wm8400_ldo_ops = { .is_enabled = regulator_is_enabled_regmap, .enable = regulator_enable_regmap, .disable = regulator_disable_regmap, - .list_voltage = wm8400_ldo_list_voltage, + .list_voltage = regulator_list_voltage_linear_range, .get_voltage_sel = regulator_get_voltage_sel_regmap, .set_voltage_sel = regulator_set_voltage_sel_regmap, - .map_voltage = wm8400_ldo_map_voltage, + .map_voltage = regulator_map_voltage_linear_range, }; static unsigned int wm8400_dcdc_get_mode(struct regulator_dev *dev) @@ -155,6 +129,8 @@ static struct regulator_desc regulators[] = { .enable_reg = WM8400_LDO1_CONTROL, .enable_mask = WM8400_LDO1_ENA, .n_voltages = WM8400_LDO1_VSEL_MASK + 1, + .linear_ranges = wm8400_ldo_ranges, + .n_linear_ranges = ARRAY_SIZE(wm8400_ldo_ranges), .vsel_reg = WM8400_LDO1_CONTROL, .vsel_mask = WM8400_LDO1_VSEL_MASK, .type = REGULATOR_VOLTAGE, @@ -167,6 +143,8 @@ static struct regulator_desc regulators[] = { .enable_reg = WM8400_LDO2_CONTROL, .enable_mask = WM8400_LDO2_ENA, .n_voltages = WM8400_LDO2_VSEL_MASK + 1, + .linear_ranges = wm8400_ldo_ranges, + .n_linear_ranges = ARRAY_SIZE(wm8400_ldo_ranges), .type = REGULATOR_VOLTAGE, .vsel_reg = WM8400_LDO2_CONTROL, .vsel_mask = WM8400_LDO2_VSEL_MASK, @@ -179,6 +157,8 @@ static struct regulator_desc regulators[] = { .enable_reg = WM8400_LDO3_CONTROL, .enable_mask = WM8400_LDO3_ENA, .n_voltages = WM8400_LDO3_VSEL_MASK + 1, + .linear_ranges = wm8400_ldo_ranges, + .n_linear_ranges = ARRAY_SIZE(wm8400_ldo_ranges), .vsel_reg = WM8400_LDO3_CONTROL, .vsel_mask = WM8400_LDO3_VSEL_MASK, .type = REGULATOR_VOLTAGE, @@ -191,6 +171,8 @@ static struct regulator_desc regulators[] = { .enable_reg = WM8400_LDO4_CONTROL, .enable_mask = WM8400_LDO4_ENA, .n_voltages = WM8400_LDO4_VSEL_MASK + 1, + .linear_ranges = wm8400_ldo_ranges, + .n_linear_ranges = ARRAY_SIZE(wm8400_ldo_ranges), .vsel_reg = WM8400_LDO4_CONTROL, .vsel_mask = WM8400_LDO4_VSEL_MASK, .type = REGULATOR_VOLTAGE, @@ -233,7 +215,7 @@ static int wm8400_regulator_probe(struct platform_device *pdev) struct regulator_dev *rdev; config.dev = &pdev->dev; - config.init_data = pdev->dev.platform_data; + config.init_data = dev_get_platdata(&pdev->dev); config.driver_data = wm8400; config.regmap = wm8400->regmap; diff --git a/drivers/regulator/wm8994-regulator.c b/drivers/regulator/wm8994-regulator.c index 8f2a8a7a3f99..5ee2a208457c 100644 --- a/drivers/regulator/wm8994-regulator.c +++ b/drivers/regulator/wm8994-regulator.c @@ -125,7 +125,7 @@ static const struct regulator_init_data wm8994_ldo_default[] = { static int wm8994_ldo_probe(struct platform_device *pdev) { struct wm8994 *wm8994 = dev_get_drvdata(pdev->dev.parent); - struct wm8994_pdata *pdata = wm8994->dev->platform_data; + struct wm8994_pdata *pdata = dev_get_platdata(wm8994->dev); int id = pdev->id % ARRAY_SIZE(pdata->ldo); struct regulator_config config = { }; struct wm8994_ldo *ldo; diff --git a/include/linux/mfd/palmas.h b/include/linux/mfd/palmas.h index 1a8dd7afe084..c06d78af3342 100644 --- a/include/linux/mfd/palmas.h +++ b/include/linux/mfd/palmas.h @@ -160,7 +160,8 @@ enum palmas_regulators { PALMAS_REG_SMPS7, PALMAS_REG_SMPS8, PALMAS_REG_SMPS9, - PALMAS_REG_SMPS10, + PALMAS_REG_SMPS10_OUT2, + PALMAS_REG_SMPS10_OUT1, /* LDO regulators */ PALMAS_REG_LDO1, PALMAS_REG_LDO2, @@ -355,9 +356,9 @@ struct palmas_pmic { int smps123; int smps457; - int range[PALMAS_REG_SMPS10]; - unsigned int ramp_delay[PALMAS_REG_SMPS10]; - unsigned int current_reg_mode[PALMAS_REG_SMPS10]; + int range[PALMAS_REG_SMPS10_OUT1]; + unsigned int ramp_delay[PALMAS_REG_SMPS10_OUT1]; + unsigned int current_reg_mode[PALMAS_REG_SMPS10_OUT1]; }; struct palmas_resource { diff --git a/include/linux/mfd/samsung/s2mps11.h b/include/linux/mfd/samsung/s2mps11.h index 4e94dc65f987..d0d52ea60074 100644 --- a/include/linux/mfd/samsung/s2mps11.h +++ b/include/linux/mfd/samsung/s2mps11.h @@ -191,6 +191,17 @@ enum s2mps11_regulators { #define S2MPS11_BUCK_N_VOLTAGES (S2MPS11_BUCK_VSEL_MASK + 1) #define S2MPS11_RAMP_DELAY 25000 /* uV/us */ + +#define S2MPS11_BUCK2_RAMP_SHIFT 6 +#define S2MPS11_BUCK34_RAMP_SHIFT 4 +#define S2MPS11_BUCK5_RAMP_SHIFT 6 +#define S2MPS11_BUCK16_RAMP_SHIFT 4 +#define S2MPS11_BUCK7810_RAMP_SHIFT 2 +#define S2MPS11_BUCK9_RAMP_SHIFT 0 +#define S2MPS11_BUCK2_RAMP_EN_SHIFT 3 +#define S2MPS11_BUCK3_RAMP_EN_SHIFT 2 +#define S2MPS11_BUCK4_RAMP_EN_SHIFT 1 +#define S2MPS11_BUCK6_RAMP_EN_SHIFT 0 #define S2MPS11_PMIC_EN_SHIFT 6 #define S2MPS11_REGULATOR_MAX (S2MPS11_REG_MAX - 3) diff --git a/include/linux/mfd/tps65217.h b/include/linux/mfd/tps65217.h index 29eab2bd3dfa..a5a7f0130e96 100644 --- a/include/linux/mfd/tps65217.h +++ b/include/linux/mfd/tps65217.h @@ -243,24 +243,6 @@ struct tps65217_board { struct tps65217_bl_pdata *bl_pdata; }; -/** - * struct tps_info - packages regulator constraints - * @name: Voltage regulator name - * @min_uV: minimum micro volts - * @max_uV: minimum micro volts - * @vsel_to_uv: Function pointer to get voltage from selector - * @uv_to_vsel: Function pointer to get selector from voltage - * - * This data is used to check the regualtor voltage limits while setting. - */ -struct tps_info { - const char *name; - int min_uV; - int max_uV; - int (*vsel_to_uv)(unsigned int vsel); - int (*uv_to_vsel)(int uV, unsigned int *vsel); -}; - /** * struct tps65217 - tps65217 sub-driver chip access routines * @@ -273,7 +255,6 @@ struct tps65217 { unsigned int id; struct regulator_desc desc[TPS65217_NUM_REGULATOR]; struct regulator_dev *rdev[TPS65217_NUM_REGULATOR]; - struct tps_info *info[TPS65217_NUM_REGULATOR]; struct regmap *regmap; }; diff --git a/include/linux/regulator/consumer.h b/include/linux/regulator/consumer.h index 3a76389c6aaa..27be915caa96 100644 --- a/include/linux/regulator/consumer.h +++ b/include/linux/regulator/consumer.h @@ -137,6 +137,12 @@ struct regulator *__must_check devm_regulator_get(struct device *dev, const char *id); struct regulator *__must_check regulator_get_exclusive(struct device *dev, const char *id); +struct regulator *__must_check devm_regulator_get_exclusive(struct device *dev, + const char *id); +struct regulator *__must_check regulator_get_optional(struct device *dev, + const char *id); +struct regulator *__must_check devm_regulator_get_optional(struct device *dev, + const char *id); void regulator_put(struct regulator *regulator); void devm_regulator_put(struct regulator *regulator); @@ -217,6 +223,25 @@ devm_regulator_get(struct device *dev, const char *id) return NULL; } +static inline struct regulator *__must_check +regulator_get_exclusive(struct device *dev, const char *id) +{ + return NULL; +} + +static inline struct regulator *__must_check +regulator_get_optional(struct device *dev, const char *id) +{ + return NULL; +} + + +static inline struct regulator *__must_check +devm_regulator_get_optional(struct device *dev, const char *id) +{ + return NULL; +} + static inline void regulator_put(struct regulator *regulator) { } @@ -369,8 +394,11 @@ static inline int regulator_count_voltages(struct regulator *regulator) static inline int regulator_set_voltage_tol(struct regulator *regulator, int new_uV, int tol_uV) { - return regulator_set_voltage(regulator, - new_uV - tol_uV, new_uV + tol_uV); + if (regulator_set_voltage(regulator, new_uV, new_uV + tol_uV) == 0) + return 0; + else + return regulator_set_voltage(regulator, + new_uV - tol_uV, new_uV + tol_uV); } static inline int regulator_is_supported_voltage_tol(struct regulator *regulator, diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h index 6700cc94bdd1..67e13aa5a478 100644 --- a/include/linux/regulator/driver.h +++ b/include/linux/regulator/driver.h @@ -39,6 +39,24 @@ enum regulator_status { REGULATOR_STATUS_UNDEFINED, }; +/** + * Specify a range of voltages for regulator_map_linar_range() and + * regulator_list_linear_range(). + * + * @min_uV: Lowest voltage in range + * @max_uV: Highest voltage in range + * @min_sel: Lowest selector for range + * @max_sel: Highest selector for range + * @uV_step: Step size + */ +struct regulator_linear_range { + unsigned int min_uV; + unsigned int max_uV; + unsigned int min_sel; + unsigned int max_sel; + unsigned int uV_step; +}; + /** * struct regulator_ops - regulator operations. * @@ -223,6 +241,9 @@ struct regulator_desc { unsigned int linear_min_sel; unsigned int ramp_delay; + const struct regulator_linear_range *linear_ranges; + int n_linear_ranges; + const unsigned int *volt_table; unsigned int vsel_reg; @@ -326,10 +347,14 @@ int regulator_mode_to_status(unsigned int); int regulator_list_voltage_linear(struct regulator_dev *rdev, unsigned int selector); +int regulator_list_voltage_linear_range(struct regulator_dev *rdev, + unsigned int selector); int regulator_list_voltage_table(struct regulator_dev *rdev, unsigned int selector); int regulator_map_voltage_linear(struct regulator_dev *rdev, int min_uV, int max_uV); +int regulator_map_voltage_linear_range(struct regulator_dev *rdev, + int min_uV, int max_uV); int regulator_map_voltage_iterate(struct regulator_dev *rdev, int min_uV, int max_uV); int regulator_map_voltage_ascend(struct regulator_dev *rdev, diff --git a/include/linux/regulator/fan53555.h b/include/linux/regulator/fan53555.h index 5c45c85d52ca..f13880e84d85 100644 --- a/include/linux/regulator/fan53555.h +++ b/include/linux/regulator/fan53555.h @@ -11,6 +11,7 @@ */ #ifndef __FAN53555_H__ +#define __FAN53555_H__ /* VSEL ID */ enum { diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h index 36adbc82de6a..999b20ce06cf 100644 --- a/include/linux/regulator/machine.h +++ b/include/linux/regulator/machine.h @@ -134,6 +134,7 @@ struct regulation_constraints { unsigned always_on:1; /* regulator never off when system is on */ unsigned boot_on:1; /* bootloader/firmware enabled regulator */ unsigned apply_uV:1; /* apply uV constraint if min == max */ + unsigned ramp_disable:1; /* disable ramp delay */ }; /** diff --git a/include/linux/regulator/max8660.h b/include/linux/regulator/max8660.h index 9936763621c7..f8a6a4844864 100644 --- a/include/linux/regulator/max8660.h +++ b/include/linux/regulator/max8660.h @@ -39,7 +39,7 @@ enum { */ struct max8660_subdev_data { int id; - char *name; + const char *name; struct regulator_init_data *platform_data; }; diff --git a/include/linux/regulator/pfuze100.h b/include/linux/regulator/pfuze100.h new file mode 100644 index 000000000000..65d550bf3954 --- /dev/null +++ b/include/linux/regulator/pfuze100.h @@ -0,0 +1,44 @@ +/* + * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + */ +#ifndef __LINUX_REG_PFUZE100_H +#define __LINUX_REG_PFUZE100_H + +#define PFUZE100_SW1AB 0 +#define PFUZE100_SW1C 1 +#define PFUZE100_SW2 2 +#define PFUZE100_SW3A 3 +#define PFUZE100_SW3B 4 +#define PFUZE100_SW4 5 +#define PFUZE100_SWBST 6 +#define PFUZE100_VSNVS 7 +#define PFUZE100_VREFDDR 8 +#define PFUZE100_VGEN1 9 +#define PFUZE100_VGEN2 10 +#define PFUZE100_VGEN3 11 +#define PFUZE100_VGEN4 12 +#define PFUZE100_VGEN5 13 +#define PFUZE100_VGEN6 14 +#define PFUZE100_MAX_REGULATOR 15 + +struct regulator_init_data; + +struct pfuze_regulator_platform_data { + struct regulator_init_data *init_data[PFUZE100_MAX_REGULATOR]; +}; + +#endif /* __LINUX_REG_PFUZE100_H */