diff --git a/Documentation/devicetree/bindings/misc/bmp085.txt b/Documentation/devicetree/bindings/misc/bmp085.txt
new file mode 100644
index 000000000000..91dfda2e4e11
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/bmp085.txt
@@ -0,0 +1,20 @@
+BMP085/BMP18x digital pressure sensors
+
+Required properties:
+- compatible: bosch,bmp085
+
+Optional properties:
+- chip-id: configurable chip id for non-default chip revisions
+- temp-measurement-period: temperature measurement period (milliseconds)
+- default-oversampling: default oversampling value to be used at startup,
+  value range is 0-3 with rising sensitivity.
+
+Example:
+
+pressure@77 {
+	compatible = "bosch,bmp085";
+	reg = <0x77>;
+	chip-id = <10>;
+	temp-measurement-period = <100>;
+	default-oversampling = <2>;
+};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 82ac057a24a9..107d8addf0e4 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -8,6 +8,7 @@ amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
 apm	Applied Micro Circuits Corporation (APM)
 arm	ARM Ltd.
 atmel	Atmel Corporation
+bosch	Bosch Sensortec GmbH
 cavium	Cavium, Inc.
 chrp	Common Hardware Reference Platform
 cortina	Cortina Systems, Inc.
diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.c b/drivers/char/xilinx_hwicap/xilinx_hwicap.c
index 31ba11ca75e1..2c5d15beea35 100644
--- a/drivers/char/xilinx_hwicap/xilinx_hwicap.c
+++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.c
@@ -167,6 +167,7 @@ static const struct config_registers v4_config_registers = {
 	.BOOTSTS = UNIMPLEMENTED,
 	.CTL_1 = UNIMPLEMENTED,
 };
+
 static const struct config_registers v5_config_registers = {
 	.CRC = 0,
 	.FAR = 1,
@@ -192,6 +193,31 @@ static const struct config_registers v5_config_registers = {
 	.CTL_1 = 19,
 };
 
+static const struct config_registers v6_config_registers = {
+	.CRC = 0,
+	.FAR = 1,
+	.FDRI = 2,
+	.FDRO = 3,
+	.CMD = 4,
+	.CTL = 5,
+	.MASK = 6,
+	.STAT = 7,
+	.LOUT = 8,
+	.COR = 9,
+	.MFWR = 10,
+	.FLR = UNIMPLEMENTED,
+	.KEY = UNIMPLEMENTED,
+	.CBC = 11,
+	.IDCODE = 12,
+	.AXSS = 13,
+	.C0R_1 = 14,
+	.CSOB = 15,
+	.WBSTAR = 16,
+	.TIMER = 17,
+	.BOOTSTS = 22,
+	.CTL_1 = 24,
+};
+
 /**
  * hwicap_command_desync - Send a DESYNC command to the ICAP port.
  * @drvdata: a pointer to the drvdata.
@@ -744,6 +770,8 @@ static int __devinit hwicap_of_probe(struct platform_device *op,
 			regs = &v4_config_registers;
 		} else if (!strcmp(family, "virtex5")) {
 			regs = &v5_config_registers;
+		} else if (!strcmp(family, "virtex6")) {
+			regs = &v6_config_registers;
 		}
 	}
 	return hwicap_setup(&op->dev, id ? *id : -1, &res, config,
@@ -785,6 +813,8 @@ static int __devinit hwicap_drv_probe(struct platform_device *pdev)
 			regs = &v4_config_registers;
 		} else if (!strcmp(family, "virtex5")) {
 			regs = &v5_config_registers;
+		} else if (!strcmp(family, "virtex6")) {
+			regs = &v6_config_registers;
 		}
 	}
 
diff --git a/drivers/char/xilinx_hwicap/xilinx_hwicap.h b/drivers/char/xilinx_hwicap/xilinx_hwicap.h
index 8cca11981c5f..d31ee23c9f13 100644
--- a/drivers/char/xilinx_hwicap/xilinx_hwicap.h
+++ b/drivers/char/xilinx_hwicap/xilinx_hwicap.h
@@ -86,7 +86,7 @@ struct hwicap_driver_config {
 };
 
 /* Number of times to poll the done regsiter */
-#define XHI_MAX_RETRIES     10
+#define XHI_MAX_RETRIES     5000
 
 /************ Constant Definitions *************/
 
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index c7795096d43b..968469555956 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -452,14 +452,32 @@ config ARM_CHARLCD
 	  still useful.
 
 config BMP085
-	tristate "BMP085 digital pressure sensor"
+	bool
+	depends on SYSFS
+
+config BMP085_I2C
+	tristate "BMP085 digital pressure sensor on I2C"
+	select BMP085
+	select REGMAP_I2C
 	depends on I2C && SYSFS
 	help
-	  If you say yes here you get support for the Bosch Sensortec
-	  BMP085 digital pressure sensor.
+	  Say Y here if you want to support Bosch Sensortec's digital pressure
+	  sensor hooked to an I2C bus.
 
 	  To compile this driver as a module, choose M here: the
-	  module will be called bmp085.
+	  module will be called bmp085-i2c.
+
+config BMP085_SPI
+	tristate "BMP085 digital pressure sensor on SPI"
+	select BMP085
+	select REGMAP_SPI
+	depends on SPI_MASTER && SYSFS
+	help
+	  Say Y here if you want to support Bosch Sensortec's digital pressure
+	  sensor hooked to an SPI bus.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bmp085-spi.
 
 config PCH_PHUB
 	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB"
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 3e1d80106f04..509d0569dc04 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -11,6 +11,8 @@ obj-$(CONFIG_ATMEL_PWM)		+= atmel_pwm.o
 obj-$(CONFIG_ATMEL_SSC)		+= atmel-ssc.o
 obj-$(CONFIG_ATMEL_TCLIB)	+= atmel_tclib.o
 obj-$(CONFIG_BMP085)		+= bmp085.o
+obj-$(CONFIG_BMP085_I2C)	+= bmp085-i2c.o
+obj-$(CONFIG_BMP085_SPI)	+= bmp085-spi.o
 obj-$(CONFIG_ICS932S401)	+= ics932s401.o
 obj-$(CONFIG_LKDTM)		+= lkdtm.o
 obj-$(CONFIG_TIFM_CORE)       	+= tifm_core.o
diff --git a/drivers/misc/ad525x_dpot.c b/drivers/misc/ad525x_dpot.c
index 1d1d42615915..6938f1be664d 100644
--- a/drivers/misc/ad525x_dpot.c
+++ b/drivers/misc/ad525x_dpot.c
@@ -749,7 +749,7 @@ exit:
 }
 EXPORT_SYMBOL(ad_dpot_probe);
 
-__devexit int ad_dpot_remove(struct device *dev)
+int ad_dpot_remove(struct device *dev)
 {
 	struct dpot_data *data = dev_get_drvdata(dev);
 	int i;
diff --git a/drivers/misc/bh1780gli.c b/drivers/misc/bh1780gli.c
index 54f6f39f990a..f1f9877f3fdf 100644
--- a/drivers/misc/bh1780gli.c
+++ b/drivers/misc/bh1780gli.c
@@ -248,7 +248,7 @@ static const struct i2c_device_id bh1780_id[] = {
 
 static struct i2c_driver bh1780_driver = {
 	.probe		= bh1780_probe,
-	.remove		= bh1780_remove,
+	.remove		= __devexit_p(bh1780_remove),
 	.id_table	= bh1780_id,
 	.driver = {
 		.name = "bh1780",
diff --git a/drivers/misc/bmp085-i2c.c b/drivers/misc/bmp085-i2c.c
new file mode 100644
index 000000000000..9943971c13e3
--- /dev/null
+++ b/drivers/misc/bmp085-i2c.c
@@ -0,0 +1,91 @@
+/*
+ * Copyright (c) 2012  Bosch Sensortec GmbH
+ * Copyright (c) 2012  Unixphere AB
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/err.h>
+#include "bmp085.h"
+
+#define BMP085_I2C_ADDRESS	0x77
+
+static const unsigned short normal_i2c[] = { BMP085_I2C_ADDRESS,
+							I2C_CLIENT_END };
+
+static int bmp085_i2c_detect(struct i2c_client *client,
+			     struct i2c_board_info *info)
+{
+	if (client->addr != BMP085_I2C_ADDRESS)
+		return -ENODEV;
+
+	return bmp085_detect(&client->dev);
+}
+
+static int __devinit bmp085_i2c_probe(struct i2c_client *client,
+				      const struct i2c_device_id *id)
+{
+	int err;
+	struct regmap *regmap = devm_regmap_init_i2c(client,
+						     &bmp085_regmap_config);
+
+	if (IS_ERR(regmap)) {
+		err = PTR_ERR(regmap);
+		dev_err(&client->dev, "Failed to init regmap: %d\n", err);
+		return err;
+	}
+
+	return bmp085_probe(&client->dev, regmap);
+}
+
+static int bmp085_i2c_remove(struct i2c_client *client)
+{
+	return bmp085_remove(&client->dev);
+}
+
+static const struct of_device_id bmp085_of_match[] = {
+	{ .compatible = "bosch,bmp085", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bmp085_of_match);
+
+static const struct i2c_device_id bmp085_id[] = {
+	{ BMP085_NAME, 0 },
+	{ "bmp180", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, bmp085_id);
+
+static struct i2c_driver bmp085_i2c_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= BMP085_NAME,
+		.of_match_table = bmp085_of_match
+	},
+	.id_table	= bmp085_id,
+	.probe		= bmp085_i2c_probe,
+	.remove		= __devexit_p(bmp085_i2c_remove),
+
+	.detect		= bmp085_i2c_detect,
+	.address_list	= normal_i2c
+};
+
+module_i2c_driver(bmp085_i2c_driver);
+
+MODULE_AUTHOR("Eric Andersson <eric.andersson@unixphere.com>");
+MODULE_DESCRIPTION("BMP085 I2C bus driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/misc/bmp085-spi.c b/drivers/misc/bmp085-spi.c
new file mode 100644
index 000000000000..78aaff9b5231
--- /dev/null
+++ b/drivers/misc/bmp085-spi.c
@@ -0,0 +1,91 @@
+/*
+ * Copyright (c) 2012  Bosch Sensortec GmbH
+ * Copyright (c) 2012  Unixphere AB
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/err.h>
+#include "bmp085.h"
+
+static int __devinit bmp085_spi_probe(struct spi_device *client)
+{
+	int err;
+	struct regmap *regmap;
+
+	client->bits_per_word = 8;
+	err = spi_setup(client);
+	if (err < 0) {
+		dev_err(&client->dev, "spi_setup failed!\n");
+		return err;
+	}
+
+	regmap = devm_regmap_init_spi(client, &bmp085_regmap_config);
+	if (IS_ERR(regmap)) {
+		err = PTR_ERR(regmap);
+		dev_err(&client->dev, "Failed to init regmap: %d\n", err);
+		return err;
+	}
+
+	return bmp085_probe(&client->dev, regmap);
+}
+
+static int bmp085_spi_remove(struct spi_device *client)
+{
+	return bmp085_remove(&client->dev);
+}
+
+static const struct of_device_id bmp085_of_match[] = {
+	{ .compatible = "bosch,bmp085", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bmp085_of_match);
+
+static const struct spi_device_id bmp085_id[] = {
+	{ "bmp180", 0 },
+	{ "bmp181", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, bmp085_id);
+
+static struct spi_driver bmp085_spi_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= BMP085_NAME,
+		.of_match_table = bmp085_of_match
+	},
+	.id_table	= bmp085_id,
+	.probe		= bmp085_spi_probe,
+	.remove		= __devexit_p(bmp085_spi_remove)
+};
+
+static int __init bmp085_spi_init(void)
+{
+	return spi_register_driver(&bmp085_spi_driver);
+}
+
+static void __exit bmp085_spi_exit(void)
+{
+	spi_unregister_driver(&bmp085_spi_driver);
+}
+
+MODULE_AUTHOR("Eric Andersson <eric.andersson@unixphere.com>");
+MODULE_DESCRIPTION("BMP085 SPI bus driver");
+MODULE_LICENSE("GPL");
+
+module_init(bmp085_spi_init);
+module_exit(bmp085_spi_exit);
diff --git a/drivers/misc/bmp085.c b/drivers/misc/bmp085.c
index 76c3064629f1..62e418293b7e 100644
--- a/drivers/misc/bmp085.c
+++ b/drivers/misc/bmp085.c
@@ -1,62 +1,62 @@
 /*  Copyright (c) 2010  Christoph Mair <christoph.mair@gmail.com>
-
-    This driver supports the bmp085 digital barometric pressure
-    and temperature sensor from Bosch Sensortec. The datasheet
-    is available from their website:
-    http://www.bosch-sensortec.com/content/language1/downloads/BST-BMP085-DS000-05.pdf
-
-    A pressure measurement is issued by reading from pressure0_input.
-    The return value ranges from 30000 to 110000 pascal with a resulution
-    of 1 pascal (0.01 millibar) which enables measurements from 9000m above
-    to 500m below sea level.
-
-    The temperature can be read from temp0_input. Values range from
-    -400 to 850 representing the ambient temperature in degree celsius
-    multiplied by 10.The resolution is 0.1 celsius.
-
-    Because ambient pressure is temperature dependent, a temperature
-    measurement will be executed automatically even if the user is reading
-    from pressure0_input. This happens if the last temperature measurement
-    has been executed more then one second ago.
-
-    To decrease RMS noise from pressure measurements, the bmp085 can
-    autonomously calculate the average of up to eight samples. This is
-    set up by writing to the oversampling sysfs file. Accepted values
-    are 0, 1, 2 and 3. 2^x when x is the value written to this file
-    specifies the number of samples used to calculate the ambient pressure.
-    RMS noise is specified with six pascal (without averaging) and decreases
-    down to 3 pascal when using an oversampling setting of 3.
-
-    This program is free software; you can redistribute it and/or modify
-    it under the terms of the GNU General Public License as published by
-    the Free Software Foundation; either version 2 of the License, or
-    (at your option) any later version.
-
-    This program is distributed in the hope that it will be useful,
-    but WITHOUT ANY WARRANTY; without even the implied warranty of
-    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-    GNU General Public License for more details.
-
-    You should have received a copy of the GNU General Public License
-    along with this program; if not, write to the Free Software
-    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-*/
-
+ *  Copyright (c) 2012  Bosch Sensortec GmbH
+ *  Copyright (c) 2012  Unixphere AB
+ *
+ *  This driver supports the bmp085 and bmp18x digital barometric pressure
+ *  and temperature sensors from Bosch Sensortec. The datasheets
+ *  are available from their website:
+ *  http://www.bosch-sensortec.com/content/language1/downloads/BST-BMP085-DS000-05.pdf
+ *  http://www.bosch-sensortec.com/content/language1/downloads/BST-BMP180-DS000-07.pdf
+ *
+ *  A pressure measurement is issued by reading from pressure0_input.
+ *  The return value ranges from 30000 to 110000 pascal with a resulution
+ *  of 1 pascal (0.01 millibar) which enables measurements from 9000m above
+ *  to 500m below sea level.
+ *
+ *  The temperature can be read from temp0_input. Values range from
+ *  -400 to 850 representing the ambient temperature in degree celsius
+ *  multiplied by 10.The resolution is 0.1 celsius.
+ *
+ *  Because ambient pressure is temperature dependent, a temperature
+ *  measurement will be executed automatically even if the user is reading
+ *  from pressure0_input. This happens if the last temperature measurement
+ *  has been executed more then one second ago.
+ *
+ *  To decrease RMS noise from pressure measurements, the bmp085 can
+ *  autonomously calculate the average of up to eight samples. This is
+ *  set up by writing to the oversampling sysfs file. Accepted values
+ *  are 0, 1, 2 and 3. 2^x when x is the value written to this file
+ *  specifies the number of samples used to calculate the ambient pressure.
+ *  RMS noise is specified with six pascal (without averaging) and decreases
+ *  down to 3 pascal when using an oversampling setting of 3.
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, write to the Free Software
+ *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
 
 #include <linux/module.h>
+#include <linux/device.h>
 #include <linux/init.h>
-#include <linux/i2c.h>
 #include <linux/slab.h>
 #include <linux/delay.h>
+#include <linux/of.h>
+#include "bmp085.h"
 
-
-#define BMP085_I2C_ADDRESS		0x77
 #define BMP085_CHIP_ID			0x55
-
 #define BMP085_CALIBRATION_DATA_START	0xAA
 #define BMP085_CALIBRATION_DATA_LENGTH	11	/* 16 bit values */
 #define BMP085_CHIP_ID_REG		0xD0
-#define BMP085_VERSION_REG		0xD1
 #define BMP085_CTRL_REG			0xF4
 #define BMP085_TEMP_MEASUREMENT		0x2E
 #define BMP085_PRESSURE_MEASUREMENT	0x34
@@ -65,12 +65,6 @@
 #define BMP085_CONVERSION_REGISTER_XLSB	0xF8
 #define BMP085_TEMP_CONVERSION_TIME	5
 
-#define BMP085_CLIENT_NAME		"bmp085"
-
-
-static const unsigned short normal_i2c[] = { BMP085_I2C_ADDRESS,
-							I2C_CLIENT_END };
-
 struct bmp085_calibration_data {
 	s16 AC1, AC2, AC3;
 	u16 AC4, AC5, AC6;
@@ -78,35 +72,30 @@ struct bmp085_calibration_data {
 	s16 MB, MC, MD;
 };
 
-
-/* Each client has this additional data */
 struct bmp085_data {
-	struct i2c_client *client;
-	struct mutex lock;
-	struct bmp085_calibration_data calibration;
-	u32 raw_temperature;
-	u32 raw_pressure;
-	unsigned char oversampling_setting;
+	struct	device *dev;
+	struct  regmap *regmap;
+	struct	mutex lock;
+	struct	bmp085_calibration_data calibration;
+	u8	oversampling_setting;
+	u32	raw_temperature;
+	u32	raw_pressure;
+	u32	temp_measurement_period;
 	unsigned long last_temp_measurement;
-	s32 b6; /* calculated temperature correction coefficient */
+	u8	chip_id;
+	s32	b6; /* calculated temperature correction coefficient */
 };
 
-
-static s32 bmp085_read_calibration_data(struct i2c_client *client)
+static s32 bmp085_read_calibration_data(struct bmp085_data *data)
 {
 	u16 tmp[BMP085_CALIBRATION_DATA_LENGTH];
-	struct bmp085_data *data = i2c_get_clientdata(client);
 	struct bmp085_calibration_data *cali = &(data->calibration);
-	s32 status = i2c_smbus_read_i2c_block_data(client,
-				BMP085_CALIBRATION_DATA_START,
-				BMP085_CALIBRATION_DATA_LENGTH*sizeof(u16),
-				(u8 *)tmp);
+	s32 status = regmap_bulk_read(data->regmap,
+				BMP085_CALIBRATION_DATA_START, (u8 *)tmp,
+				(BMP085_CALIBRATION_DATA_LENGTH << 1));
 	if (status < 0)
 		return status;
 
-	if (status != BMP085_CALIBRATION_DATA_LENGTH*sizeof(u16))
-		return -EIO;
-
 	cali->AC1 =  be16_to_cpu(tmp[0]);
 	cali->AC2 =  be16_to_cpu(tmp[1]);
 	cali->AC3 =  be16_to_cpu(tmp[2]);
@@ -121,30 +110,26 @@ static s32 bmp085_read_calibration_data(struct i2c_client *client)
 	return 0;
 }
 
-
 static s32 bmp085_update_raw_temperature(struct bmp085_data *data)
 {
 	u16 tmp;
 	s32 status;
 
 	mutex_lock(&data->lock);
-	status = i2c_smbus_write_byte_data(data->client, BMP085_CTRL_REG,
-						BMP085_TEMP_MEASUREMENT);
-	if (status != 0) {
-		dev_err(&data->client->dev,
+	status = regmap_write(data->regmap, BMP085_CTRL_REG,
+			      BMP085_TEMP_MEASUREMENT);
+	if (status < 0) {
+		dev_err(data->dev,
 			"Error while requesting temperature measurement.\n");
 		goto exit;
 	}
 	msleep(BMP085_TEMP_CONVERSION_TIME);
 
-	status = i2c_smbus_read_i2c_block_data(data->client,
-		BMP085_CONVERSION_REGISTER_MSB, sizeof(tmp), (u8 *)&tmp);
-	if (status < 0)
-		goto exit;
-	if (status != sizeof(tmp)) {
-		dev_err(&data->client->dev,
+	status = regmap_bulk_read(data->regmap, BMP085_CONVERSION_REGISTER_MSB,
+				 &tmp, sizeof(tmp));
+	if (status < 0) {
+		dev_err(data->dev,
 			"Error while reading temperature measurement result\n");
-		status = -EIO;
 		goto exit;
 	}
 	data->raw_temperature = be16_to_cpu(tmp);
@@ -162,10 +147,11 @@ static s32 bmp085_update_raw_pressure(struct bmp085_data *data)
 	s32 status;
 
 	mutex_lock(&data->lock);
-	status = i2c_smbus_write_byte_data(data->client, BMP085_CTRL_REG,
-		BMP085_PRESSURE_MEASUREMENT + (data->oversampling_setting<<6));
-	if (status != 0) {
-		dev_err(&data->client->dev,
+	status = regmap_write(data->regmap, BMP085_CTRL_REG,
+			BMP085_PRESSURE_MEASUREMENT +
+			(data->oversampling_setting << 6));
+	if (status < 0) {
+		dev_err(data->dev,
 			"Error while requesting pressure measurement.\n");
 		goto exit;
 	}
@@ -174,14 +160,11 @@ static s32 bmp085_update_raw_pressure(struct bmp085_data *data)
 	msleep(2+(3 << data->oversampling_setting));
 
 	/* copy data into a u32 (4 bytes), but skip the first byte. */
-	status = i2c_smbus_read_i2c_block_data(data->client,
-			BMP085_CONVERSION_REGISTER_MSB, 3, ((u8 *)&tmp)+1);
-	if (status < 0)
-		goto exit;
-	if (status != 3) {
-		dev_err(&data->client->dev,
+	status = regmap_bulk_read(data->regmap, BMP085_CONVERSION_REGISTER_MSB,
+				 ((u8 *)&tmp)+1, 3);
+	if (status < 0) {
+		dev_err(data->dev,
 			"Error while reading pressure measurement results\n");
-		status = -EIO;
 		goto exit;
 	}
 	data->raw_pressure = be32_to_cpu((tmp));
@@ -193,7 +176,6 @@ exit:
 	return status;
 }
 
-
 /*
  * This function starts the temperature measurement and returns the value
  * in tenth of a degree celsius.
@@ -205,7 +187,7 @@ static s32 bmp085_get_temperature(struct bmp085_data *data, int *temperature)
 	int status;
 
 	status = bmp085_update_raw_temperature(data);
-	if (status != 0)
+	if (status < 0)
 		goto exit;
 
 	x1 = ((data->raw_temperature - cali->AC6) * cali->AC5) >> 15;
@@ -222,8 +204,10 @@ exit:
 /*
  * This function starts the pressure measurement and returns the value
  * in millibar. Since the pressure depends on the ambient temperature,
- * a temperature measurement is executed if the last known value is older
- * than one second.
+ * a temperature measurement is executed according to the given temperature
+ * measurement period (default is 1 sec boundary). This period could vary
+ * and needs to be adjusted according to the sensor environment, i.e. if big
+ * temperature variations then the temperature needs to be read out often.
  */
 static s32 bmp085_get_pressure(struct bmp085_data *data, int *pressure)
 {
@@ -234,16 +218,16 @@ static s32 bmp085_get_pressure(struct bmp085_data *data, int *pressure)
 	int status;
 
 	/* alt least every second force an update of the ambient temperature */
-	if (data->last_temp_measurement == 0 ||
-			time_is_before_jiffies(data->last_temp_measurement + 1*HZ)) {
+	if ((data->last_temp_measurement == 0) ||
+	    time_is_before_jiffies(data->last_temp_measurement + 1*HZ)) {
 		status = bmp085_get_temperature(data, NULL);
-		if (status != 0)
-			goto exit;
+		if (status < 0)
+			return status;
 	}
 
 	status = bmp085_update_raw_pressure(data);
-	if (status != 0)
-		goto exit;
+	if (status < 0)
+		return status;
 
 	x1 = (data->b6 * data->b6) >> 12;
 	x1 *= cali->B2;
@@ -274,15 +258,14 @@ static s32 bmp085_get_pressure(struct bmp085_data *data, int *pressure)
 
 	*pressure = p;
 
-exit:
-	return status;
+	return 0;
 }
 
 /*
  * This function sets the chip-internal oversampling. Valid values are 0..3.
  * The chip will use 2^oversampling samples for internal averaging.
  * This influences the measurement time and the accuracy; larger values
- * increase both. The datasheet gives on overview on how measurement time,
+ * increase both. The datasheet gives an overview on how measurement time,
  * accuracy and noise correlate.
  */
 static void bmp085_set_oversampling(struct bmp085_data *data,
@@ -306,22 +289,25 @@ static ssize_t set_oversampling(struct device *dev,
 				struct device_attribute *attr,
 				const char *buf, size_t count)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct bmp085_data *data = i2c_get_clientdata(client);
+	struct bmp085_data *data = dev_get_drvdata(dev);
 	unsigned long oversampling;
-	int success = strict_strtoul(buf, 10, &oversampling);
-	if (success == 0) {
+	int err = kstrtoul(buf, 10, &oversampling);
+
+	if (err == 0) {
+		mutex_lock(&data->lock);
 		bmp085_set_oversampling(data, oversampling);
+		mutex_unlock(&data->lock);
 		return count;
 	}
-	return success;
+
+	return err;
 }
 
 static ssize_t show_oversampling(struct device *dev,
 				 struct device_attribute *attr, char *buf)
 {
-	struct i2c_client *client = to_i2c_client(dev);
-	struct bmp085_data *data = i2c_get_clientdata(client);
+	struct bmp085_data *data = dev_get_drvdata(dev);
+
 	return sprintf(buf, "%u\n", bmp085_get_oversampling(data));
 }
 static DEVICE_ATTR(oversampling, S_IWUSR | S_IRUGO,
@@ -333,11 +319,10 @@ static ssize_t show_temperature(struct device *dev,
 {
 	int temperature;
 	int status;
-	struct i2c_client *client = to_i2c_client(dev);
-	struct bmp085_data *data = i2c_get_clientdata(client);
+	struct bmp085_data *data = dev_get_drvdata(dev);
 
 	status = bmp085_get_temperature(data, &temperature);
-	if (status != 0)
+	if (status < 0)
 		return status;
 	else
 		return sprintf(buf, "%d\n", temperature);
@@ -350,11 +335,10 @@ static ssize_t show_pressure(struct device *dev,
 {
 	int pressure;
 	int status;
-	struct i2c_client *client = to_i2c_client(dev);
-	struct bmp085_data *data = i2c_get_clientdata(client);
+	struct bmp085_data *data = dev_get_drvdata(dev);
 
 	status = bmp085_get_pressure(data, &pressure);
-	if (status != 0)
+	if (status < 0)
 		return status;
 	else
 		return sprintf(buf, "%d\n", pressure);
@@ -373,38 +357,70 @@ static const struct attribute_group bmp085_attr_group = {
 	.attrs = bmp085_attributes,
 };
 
-static int bmp085_detect(struct i2c_client *client, struct i2c_board_info *info)
+int bmp085_detect(struct device *dev)
 {
-	if (client->addr != BMP085_I2C_ADDRESS)
-		return -ENODEV;
+	struct bmp085_data *data = dev_get_drvdata(dev);
+	unsigned int id;
+	int ret;
 
-	if (i2c_smbus_read_byte_data(client, BMP085_CHIP_ID_REG) != BMP085_CHIP_ID)
+	ret = regmap_read(data->regmap, BMP085_CHIP_ID_REG, &id);
+	if (ret < 0)
+		return ret;
+
+	if (id != data->chip_id)
 		return -ENODEV;
 
 	return 0;
 }
+EXPORT_SYMBOL_GPL(bmp085_detect);
 
-static int bmp085_init_client(struct i2c_client *client)
+static void __init bmp085_get_of_properties(struct bmp085_data *data)
 {
-	unsigned char version;
-	int status;
-	struct bmp085_data *data = i2c_get_clientdata(client);
-	data->client = client;
-	status = bmp085_read_calibration_data(client);
-	if (status != 0)
-		goto exit;
-	version = i2c_smbus_read_byte_data(client, BMP085_VERSION_REG);
-	data->last_temp_measurement = 0;
-	data->oversampling_setting = 3;
-	mutex_init(&data->lock);
-	dev_info(&data->client->dev, "BMP085 ver. %d.%d found.\n",
-			(version & 0x0F), (version & 0xF0) >> 4);
-exit:
-	return status;
+#ifdef CONFIG_OF
+	struct device_node *np = data->dev->of_node;
+	u32 prop;
+
+	if (!np)
+		return;
+
+	if (!of_property_read_u32(np, "chip-id", &prop))
+		data->chip_id = prop & 0xff;
+
+	if (!of_property_read_u32(np, "temp-measurement-period", &prop))
+		data->temp_measurement_period = (prop/100)*HZ;
+
+	if (!of_property_read_u32(np, "default-oversampling", &prop))
+		data->oversampling_setting = prop & 0xff;
+#endif
 }
 
-static int __devinit bmp085_probe(struct i2c_client *client,
-			 const struct i2c_device_id *id)
+static int bmp085_init_client(struct bmp085_data *data)
+{
+	int status = bmp085_read_calibration_data(data);
+
+	if (status < 0)
+		return status;
+
+	/* default settings */
+	data->chip_id = BMP085_CHIP_ID;
+	data->last_temp_measurement = 0;
+	data->temp_measurement_period = 1*HZ;
+	data->oversampling_setting = 3;
+
+	bmp085_get_of_properties(data);
+
+	mutex_init(&data->lock);
+
+	return 0;
+}
+
+struct regmap_config bmp085_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8
+};
+EXPORT_SYMBOL_GPL(bmp085_regmap_config);
+
+__devinit int bmp085_probe(struct device *dev, struct regmap *regmap)
 {
 	struct bmp085_data *data;
 	int err = 0;
@@ -415,58 +431,48 @@ static int __devinit bmp085_probe(struct i2c_client *client,
 		goto exit;
 	}
 
-	/* default settings after POR */
-	data->oversampling_setting = 0x00;
-
-	i2c_set_clientdata(client, data);
+	dev_set_drvdata(dev, data);
+	data->dev = dev;
+	data->regmap = regmap;
 
 	/* Initialize the BMP085 chip */
-	err = bmp085_init_client(client);
-	if (err != 0)
+	err = bmp085_init_client(data);
+	if (err < 0)
 		goto exit_free;
 
+	err = bmp085_detect(dev);
+	if (err < 0) {
+		dev_err(dev, "%s: chip_id failed!\n", BMP085_NAME);
+		goto exit_free;
+	}
+
 	/* Register sysfs hooks */
-	err = sysfs_create_group(&client->dev.kobj, &bmp085_attr_group);
+	err = sysfs_create_group(&dev->kobj, &bmp085_attr_group);
 	if (err)
 		goto exit_free;
 
-	dev_info(&data->client->dev, "Successfully initialized bmp085!\n");
-	goto exit;
+	dev_info(dev, "Successfully initialized %s!\n", BMP085_NAME);
+
+	return 0;
 
 exit_free:
 	kfree(data);
 exit:
 	return err;
 }
+EXPORT_SYMBOL_GPL(bmp085_probe);
 
-static int __devexit bmp085_remove(struct i2c_client *client)
+int bmp085_remove(struct device *dev)
 {
-	sysfs_remove_group(&client->dev.kobj, &bmp085_attr_group);
-	kfree(i2c_get_clientdata(client));
+	struct bmp085_data *data = dev_get_drvdata(dev);
+
+	sysfs_remove_group(&data->dev->kobj, &bmp085_attr_group);
+	kfree(data);
+
 	return 0;
 }
+EXPORT_SYMBOL_GPL(bmp085_remove);
 
-static const struct i2c_device_id bmp085_id[] = {
-	{ "bmp085", 0 },
-	{ }
-};
-MODULE_DEVICE_TABLE(i2c, bmp085_id);
-
-static struct i2c_driver bmp085_driver = {
-	.driver = {
-		.owner = THIS_MODULE,
-		.name	= "bmp085"
-	},
-	.id_table	= bmp085_id,
-	.probe		= bmp085_probe,
-	.remove		= __devexit_p(bmp085_remove),
-
-	.detect		= bmp085_detect,
-	.address_list	= normal_i2c
-};
-
-module_i2c_driver(bmp085_driver);
-
-MODULE_AUTHOR("Christoph Mair <christoph.mair@gmail.com");
+MODULE_AUTHOR("Christoph Mair <christoph.mair@gmail.com>");
 MODULE_DESCRIPTION("BMP085 driver");
 MODULE_LICENSE("GPL");
diff --git a/drivers/misc/bmp085.h b/drivers/misc/bmp085.h
new file mode 100644
index 000000000000..2b8f615bca92
--- /dev/null
+++ b/drivers/misc/bmp085.h
@@ -0,0 +1,33 @@
+/*
+ * Copyright (c) 2012  Bosch Sensortec GmbH
+ * Copyright (c) 2012  Unixphere AB
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef _BMP085_H
+#define _BMP085_H
+
+#include <linux/regmap.h>
+
+#define BMP085_NAME		"bmp085"
+
+extern struct regmap_config bmp085_regmap_config;
+
+int bmp085_probe(struct device *dev, struct regmap *regmap);
+int bmp085_remove(struct device *dev);
+int bmp085_detect(struct device *dev);
+
+#endif
diff --git a/drivers/misc/eeprom/at25.c b/drivers/misc/eeprom/at25.c
index 01ab3c9b4cf7..0842c2994ee2 100644
--- a/drivers/misc/eeprom/at25.c
+++ b/drivers/misc/eeprom/at25.c
@@ -50,6 +50,7 @@ struct at25_data {
 #define	AT25_SR_BP1	0x08
 #define	AT25_SR_WPEN	0x80		/* writeprotect enable */
 
+#define	AT25_INSTR_BIT3	0x08		/* Additional address bit in instr */
 
 #define EE_MAXADDRLEN	3		/* 24 bit addresses, up to 2 MBytes */
 
@@ -75,6 +76,7 @@ at25_ee_read(
 	ssize_t			status;
 	struct spi_transfer	t[2];
 	struct spi_message	m;
+	u8			instr;
 
 	if (unlikely(offset >= at25->bin.size))
 		return 0;
@@ -84,7 +86,12 @@ at25_ee_read(
 		return count;
 
 	cp = command;
-	*cp++ = AT25_READ;
+
+	instr = AT25_READ;
+	if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
+		if (offset >= (1U << (at25->addrlen * 8)))
+			instr |= AT25_INSTR_BIT3;
+	*cp++ = instr;
 
 	/* 8/16/24-bit address is written MSB first */
 	switch (at25->addrlen) {
@@ -167,14 +174,14 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off,
 	/* For write, rollover is within the page ... so we write at
 	 * most one page, then manually roll over to the next page.
 	 */
-	bounce[0] = AT25_WRITE;
 	mutex_lock(&at25->lock);
 	do {
 		unsigned long	timeout, retries;
 		unsigned	segment;
 		unsigned	offset = (unsigned) off;
-		u8		*cp = bounce + 1;
+		u8		*cp = bounce;
 		int		sr;
+		u8		instr;
 
 		*cp = AT25_WREN;
 		status = spi_write(at25->spi, cp, 1);
@@ -184,6 +191,12 @@ at25_ee_write(struct at25_data *at25, const char *buf, loff_t off,
 			break;
 		}
 
+		instr = AT25_WRITE;
+		if (at25->chip.flags & EE_INSTR_BIT3_IS_ADDR)
+			if (offset >= (1U << (at25->addrlen * 8)))
+				instr |= AT25_INSTR_BIT3;
+		*cp++ = instr;
+
 		/* 8/16/24-bit address is written MSB first */
 		switch (at25->addrlen) {
 		default:	/* case 3 */
diff --git a/drivers/misc/max8997-muic.c b/drivers/misc/max8997-muic.c
index 19591eaa492a..2e7df9c56491 100644
--- a/drivers/misc/max8997-muic.c
+++ b/drivers/misc/max8997-muic.c
@@ -440,10 +440,6 @@ static int __devinit max8997_muic_probe(struct platform_device *pdev)
 				"failed: irq request (IRQ: %d,"
 				" error :%d)\n",
 				muic_irq->irq, ret);
-
-			for (i = i - 1; i >= 0; i--)
-				free_irq(muic_irq->irq, info);
-
 			goto err_irq;
 		}
 	}
@@ -457,6 +453,8 @@ static int __devinit max8997_muic_probe(struct platform_device *pdev)
 	return ret;
 
 err_irq:
+	while (--i >= 0)
+		free_irq(pdata->irq_base + muic_irqs[i].irq, info);
 err_pdata:
 	kfree(info);
 err_kfree:
diff --git a/drivers/misc/pch_phub.c b/drivers/misc/pch_phub.c
index 10fc4785dba7..9fbcacd703d5 100644
--- a/drivers/misc/pch_phub.c
+++ b/drivers/misc/pch_phub.c
@@ -65,10 +65,6 @@
 #define PCI_VENDOR_ID_ROHM			0x10db
 #define PCI_DEVICE_ID_ROHM_ML7213_PHUB		0x801A
 
-/* Macros for ML7213 */
-#define PCI_VENDOR_ID_ROHM			0x10db
-#define PCI_DEVICE_ID_ROHM_ML7213_PHUB		0x801A
-
 /* Macros for ML7223 */
 #define PCI_DEVICE_ID_ROHM_ML7223_mPHUB	0x8012 /* for Bus-m */
 #define PCI_DEVICE_ID_ROHM_ML7223_nPHUB	0x8002 /* for Bus-n */
diff --git a/drivers/misc/pti.c b/drivers/misc/pti.c
index 383133b201a1..b7eb545394b1 100644
--- a/drivers/misc/pti.c
+++ b/drivers/misc/pti.c
@@ -888,7 +888,7 @@ static struct pci_driver pti_pci_driver = {
 	.name		= PCINAME,
 	.id_table	= pci_ids,
 	.probe		= pti_pci_probe,
-	.remove		= pti_pci_remove,
+	.remove		= __devexit_p(pti_pci_remove),
 };
 
 /**
diff --git a/drivers/parport/parport_amiga.c b/drivers/parport/parport_amiga.c
index 8bef6d60f88b..ee78e0ee6e05 100644
--- a/drivers/parport/parport_amiga.c
+++ b/drivers/parport/parport_amiga.c
@@ -48,23 +48,6 @@ static unsigned char amiga_read_data(struct parport *p)
 	return ciaa.prb;
 }
 
-#if 0
-static unsigned char control_pc_to_amiga(unsigned char control)
-{
-	unsigned char ret = 0;
-
-	if (control & PARPORT_CONTROL_SELECT) /* XXX: What is SELECP? */
-		;
-	if (control & PARPORT_CONTROL_INIT) /* INITP */
-		/* reset connected to cpu reset pin */;
-	if (control & PARPORT_CONTROL_AUTOFD) /* AUTOLF */
-		/* Not connected */;
-	if (control & PARPORT_CONTROL_STROBE) /* Strobe */
-		/* Handled only directly by hardware */;
-	return ret;
-}
-#endif
-
 static unsigned char control_amiga_to_pc(unsigned char control)
 {
 	return PARPORT_CONTROL_SELECT |
@@ -95,25 +78,6 @@ static unsigned char amiga_frob_control( struct parport *p, unsigned char mask,
 	return old;
 }
 
-#if 0 /* currently unused */
-static unsigned char status_pc_to_amiga(unsigned char status)
-{
-	unsigned char ret = 1;
-
-	if (status & PARPORT_STATUS_BUSY) /* Busy */
-		ret &= ~1;
-	if (status & PARPORT_STATUS_ACK) /* Ack */
-		/* handled in hardware */;
-	if (status & PARPORT_STATUS_PAPEROUT) /* PaperOut */
-		ret |= 2;
-	if (status & PARPORT_STATUS_SELECT) /* select */
-		ret |= 4;
-	if (status & PARPORT_STATUS_ERROR) /* error */
-		/* not connected */;
-	return ret;
-}
-#endif
-
 static unsigned char status_amiga_to_pc(unsigned char status)
 {
 	unsigned char ret = PARPORT_STATUS_BUSY | PARPORT_STATUS_ACK | PARPORT_STATUS_ERROR;
diff --git a/drivers/parport/parport_atari.c b/drivers/parport/parport_atari.c
index 0b28fccec03f..7ad59ac68cf6 100644
--- a/drivers/parport/parport_atari.c
+++ b/drivers/parport/parport_atari.c
@@ -130,15 +130,6 @@ parport_atari_data_forward(struct parport *p)
 static void
 parport_atari_data_reverse(struct parport *p)
 {
-#if 0 /* too dangerous, can kill sound chip */
-	unsigned long flags;
-
-	local_irq_save(flags);
-	/* Soundchip port B as input. */
-	sound_ym.rd_data_reg_sel = 7;
-	sound_ym.wd_data = sound_ym.rd_data_reg_sel & ~0x40;
-	local_irq_restore(flags);
-#endif
 }
 
 static struct parport_operations parport_atari_ops = {
diff --git a/drivers/parport/parport_mfc3.c b/drivers/parport/parport_mfc3.c
index 1c0c642b3e23..7578d79b3688 100644
--- a/drivers/parport/parport_mfc3.c
+++ b/drivers/parport/parport_mfc3.c
@@ -147,25 +147,6 @@ DPRINTK(KERN_DEBUG "frob_control mask %02x, value %02x\n",mask,val);
 	return old;
 }
 
-#if 0 /* currently unused */
-static unsigned char status_pc_to_mfc3(unsigned char status)
-{
-	unsigned char ret = 1;
-
-	if (status & PARPORT_STATUS_BUSY) /* Busy */
-		ret &= ~1;
-	if (status & PARPORT_STATUS_ACK) /* Ack */
-		ret |= 8;
-	if (status & PARPORT_STATUS_PAPEROUT) /* PaperOut */
-		ret |= 2;
-	if (status & PARPORT_STATUS_SELECT) /* select */
-		ret |= 4;
-	if (status & PARPORT_STATUS_ERROR) /* error */
-		ret |= 16;
-	return ret;
-}
-#endif
-
 static unsigned char status_mfc3_to_pc(unsigned char status)
 {
 	unsigned char ret = PARPORT_STATUS_BUSY;
@@ -184,14 +165,6 @@ static unsigned char status_mfc3_to_pc(unsigned char status)
 	return ret;
 }
 
-#if 0 /* currently unused */
-static void mfc3_write_status( struct parport *p, unsigned char status)
-{
-DPRINTK(KERN_DEBUG "write_status %02x\n",status);
-	pia(p)->ppra = (pia(p)->ppra & 0xe0) | status_pc_to_mfc3(status);
-}
-#endif
-
 static unsigned char mfc3_read_status(struct parport *p)
 {
 	unsigned char status;
@@ -201,14 +174,6 @@ DPRINTK(KERN_DEBUG "read_status %02x\n", status);
 	return status;
 }
 
-#if 0 /* currently unused */
-static void mfc3_change_mode( struct parport *p, int m)
-{
-	/* XXX: This port only has one mode, and I am
-	not sure about the corresponding PC-style mode*/
-}
-#endif
-
 static int use_cnt = 0;
 
 static irqreturn_t mfc3_interrupt(int irq, void *dev_id)
diff --git a/drivers/parport/parport_pc.c b/drivers/parport/parport_pc.c
index 0cb64f50cecd..402956321d33 100644
--- a/drivers/parport/parport_pc.c
+++ b/drivers/parport/parport_pc.c
@@ -197,54 +197,6 @@ static int change_mode(struct parport *p, int m)
 	ECR_WRITE(p, oecr);
 	return 0;
 }
-
-#ifdef CONFIG_PARPORT_1284
-/* Find FIFO lossage; FIFO is reset */
-#if 0
-static int get_fifo_residue(struct parport *p)
-{
-	int residue;
-	int cnfga;
-	const struct parport_pc_private *priv = p->physport->private_data;
-
-	/* Adjust for the contents of the FIFO. */
-	for (residue = priv->fifo_depth; ; residue--) {
-		if (inb(ECONTROL(p)) & 0x2)
-				/* Full up. */
-			break;
-
-		outb(0, FIFO(p));
-	}
-
-	printk(KERN_DEBUG "%s: %d PWords were left in FIFO\n", p->name,
-		residue);
-
-	/* Reset the FIFO. */
-	frob_set_mode(p, ECR_PS2);
-
-	/* Now change to config mode and clean up. FIXME */
-	frob_set_mode(p, ECR_CNF);
-	cnfga = inb(CONFIGA(p));
-	printk(KERN_DEBUG "%s: cnfgA contains 0x%02x\n", p->name, cnfga);
-
-	if (!(cnfga & (1<<2))) {
-		printk(KERN_DEBUG "%s: Accounting for extra byte\n", p->name);
-		residue++;
-	}
-
-	/* Don't care about partial PWords until support is added for
-	 * PWord != 1 byte. */
-
-	/* Back to PS2 mode. */
-	frob_set_mode(p, ECR_PS2);
-
-	DPRINTK(KERN_DEBUG
-	     "*** get_fifo_residue: done residue collecting (ecr = 0x%2.2x)\n",
-							inb(ECONTROL(p)));
-	return residue;
-}
-#endif  /*  0 */
-#endif /* IEEE 1284 support */
 #endif /* FIFO support */
 
 /*
@@ -940,234 +892,6 @@ static size_t parport_pc_ecp_write_block_pio(struct parport *port,
 
 	return written;
 }
-
-#if 0
-static size_t parport_pc_ecp_read_block_pio(struct parport *port,
-					     void *buf, size_t length,
-					     int flags)
-{
-	size_t left = length;
-	size_t fifofull;
-	int r;
-	const int fifo = FIFO(port);
-	const struct parport_pc_private *priv = port->physport->private_data;
-	const int fifo_depth = priv->fifo_depth;
-	char *bufp = buf;
-
-	port = port->physport;
-	DPRINTK(KERN_DEBUG "parport_pc: parport_pc_ecp_read_block_pio\n");
-	dump_parport_state("enter fcn", port);
-
-	/* Special case: a timeout of zero means we cannot call schedule().
-	 * Also if O_NONBLOCK is set then use the default implementation. */
-	if (port->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
-		return parport_ieee1284_ecp_read_data(port, buf,
-						       length, flags);
-
-	if (port->ieee1284.mode == IEEE1284_MODE_ECPRLE) {
-		/* If the peripheral is allowed to send RLE compressed
-		 * data, it is possible for a byte to expand to 128
-		 * bytes in the FIFO. */
-		fifofull = 128;
-	} else {
-		fifofull = fifo_depth;
-	}
-
-	/* If the caller wants less than a full FIFO's worth of data,
-	 * go through software emulation.  Otherwise we may have to throw
-	 * away data. */
-	if (length < fifofull)
-		return parport_ieee1284_ecp_read_data(port, buf,
-						       length, flags);
-
-	if (port->ieee1284.phase != IEEE1284_PH_REV_IDLE) {
-		/* change to reverse-idle phase (must be in forward-idle) */
-
-		/* Event 38: Set nAutoFd low (also make sure nStrobe is high) */
-		parport_frob_control(port,
-				      PARPORT_CONTROL_AUTOFD
-				      | PARPORT_CONTROL_STROBE,
-				      PARPORT_CONTROL_AUTOFD);
-		parport_pc_data_reverse(port); /* Must be in PS2 mode */
-		udelay(5);
-		/* Event 39: Set nInit low to initiate bus reversal */
-		parport_frob_control(port,
-				      PARPORT_CONTROL_INIT,
-				      0);
-		/* Event 40: Wait for  nAckReverse (PError) to go low */
-		r = parport_wait_peripheral(port, PARPORT_STATUS_PAPEROUT, 0);
-		if (r) {
-			printk(KERN_DEBUG "%s: PE timeout Event 40 (%d) "
-				"in ecp_read_block_pio\n", port->name, r);
-			return 0;
-		}
-	}
-
-	/* Set up ECP FIFO mode.*/
-/*	parport_pc_frob_control(port,
-				 PARPORT_CONTROL_STROBE |
-				 PARPORT_CONTROL_AUTOFD,
-				 PARPORT_CONTROL_AUTOFD); */
-	r = change_mode(port, ECR_ECP); /* ECP FIFO */
-	if (r)
-		printk(KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n",
-								port->name);
-
-	port->ieee1284.phase = IEEE1284_PH_REV_DATA;
-
-	/* the first byte must be collected manually */
-	dump_parport_state("pre 43", port);
-	/* Event 43: Wait for nAck to go low */
-	r = parport_wait_peripheral(port, PARPORT_STATUS_ACK, 0);
-	if (r) {
-		/* timed out while reading -- no data */
-		printk(KERN_DEBUG "PIO read timed out (initial byte)\n");
-		goto out_no_data;
-	}
-	/* read byte */
-	*bufp++ = inb(DATA(port));
-	left--;
-	dump_parport_state("43-44", port);
-	/* Event 44: nAutoFd (HostAck) goes high to acknowledge */
-	parport_pc_frob_control(port,
-				 PARPORT_CONTROL_AUTOFD,
-				 0);
-	dump_parport_state("pre 45", port);
-	/* Event 45: Wait for nAck to go high */
-	/* r = parport_wait_peripheral(port, PARPORT_STATUS_ACK,
-						PARPORT_STATUS_ACK); */
-	dump_parport_state("post 45", port);
-	r = 0;
-	if (r) {
-		/* timed out while waiting for peripheral to respond to ack */
-		printk(KERN_DEBUG "ECP PIO read timed out (waiting for nAck)\n");
-
-		/* keep hold of the byte we've got already */
-		goto out_no_data;
-	}
-	/* Event 46: nAutoFd (HostAck) goes low to accept more data */
-	parport_pc_frob_control(port,
-				 PARPORT_CONTROL_AUTOFD,
-				 PARPORT_CONTROL_AUTOFD);
-
-
-	dump_parport_state("rev idle", port);
-	/* Do the transfer. */
-	while (left > fifofull) {
-		int ret;
-		unsigned long expire = jiffies + port->cad->timeout;
-		unsigned char ecrval = inb(ECONTROL(port));
-
-		if (need_resched() && time_before(jiffies, expire))
-			/* Can't yield the port. */
-			schedule();
-
-		/* At this point, the FIFO may already be full. In
-		 * that case ECP is already holding back the
-		 * peripheral (assuming proper design) with a delayed
-		 * handshake.  Work fast to avoid a peripheral
-		 * timeout.  */
-
-		if (ecrval & 0x01) {
-			/* FIFO is empty. Wait for interrupt. */
-			dump_parport_state("FIFO empty", port);
-
-			/* Anyone else waiting for the port? */
-			if (port->waithead) {
-				printk(KERN_DEBUG "Somebody wants the port\n");
-				break;
-			}
-
-			/* Clear serviceIntr */
-			ECR_WRITE(port, ecrval & ~(1<<2));
-false_alarm:
-			dump_parport_state("waiting", port);
-			ret = parport_wait_event(port, HZ);
-			DPRINTK(KERN_DEBUG "parport_wait_event returned %d\n",
-									ret);
-			if (ret < 0)
-				break;
-			ret = 0;
-			if (!time_before(jiffies, expire)) {
-				/* Timed out. */
-				dump_parport_state("timeout", port);
-				printk(KERN_DEBUG "PIO read timed out\n");
-				break;
-			}
-			ecrval = inb(ECONTROL(port));
-			if (!(ecrval & (1<<2))) {
-				if (need_resched() &&
-				    time_before(jiffies, expire)) {
-					schedule();
-				}
-				goto false_alarm;
-			}
-
-			/* Depending on how the FIFO threshold was
-			 * set, how long interrupt service took, and
-			 * how fast the peripheral is, we might be
-			 * lucky and have a just filled FIFO. */
-			continue;
-		}
-
-		if (ecrval & 0x02) {
-			/* FIFO is full. */
-			dump_parport_state("FIFO full", port);
-			insb(fifo, bufp, fifo_depth);
-			bufp += fifo_depth;
-			left -= fifo_depth;
-			continue;
-		}
-
-		DPRINTK(KERN_DEBUG
-		  "*** ecp_read_block_pio: reading one byte from the FIFO\n");
-
-		/* FIFO not filled.  We will cycle this loop for a while
-		 * and either the peripheral will fill it faster,
-		 * tripping a fast empty with insb, or we empty it. */
-		*bufp++ = inb(fifo);
-		left--;
-	}
-
-	/* scoop up anything left in the FIFO */
-	while (left && !(inb(ECONTROL(port) & 0x01))) {
-		*bufp++ = inb(fifo);
-		left--;
-	}
-
-	port->ieee1284.phase = IEEE1284_PH_REV_IDLE;
-	dump_parport_state("rev idle2", port);
-
-out_no_data:
-
-	/* Go to forward idle mode to shut the peripheral up (event 47). */
-	parport_frob_control(port, PARPORT_CONTROL_INIT, PARPORT_CONTROL_INIT);
-
-	/* event 49: PError goes high */
-	r = parport_wait_peripheral(port,
-				     PARPORT_STATUS_PAPEROUT,
-				     PARPORT_STATUS_PAPEROUT);
-	if (r) {
-		printk(KERN_DEBUG
-			"%s: PE timeout FWDIDLE (%d) in ecp_read_block_pio\n",
-			port->name, r);
-	}
-
-	port->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
-
-	/* Finish up. */
-	{
-		int lost = get_fifo_residue(port);
-		if (lost)
-			/* Shouldn't happen with compliant peripherals. */
-			printk(KERN_DEBUG "%s: DATA LOSS (%d bytes)!\n",
-				port->name, lost);
-	}
-
-	dump_parport_state("fwd idle", port);
-	return length - left;
-}
-#endif  /*  0  */
 #endif /* IEEE 1284 support */
 #endif /* Allowed to use FIFO/DMA */
 
diff --git a/drivers/parport/parport_sunbpp.c b/drivers/parport/parport_sunbpp.c
index 9390a534a2b2..983a2d2df659 100644
--- a/drivers/parport/parport_sunbpp.c
+++ b/drivers/parport/parport_sunbpp.c
@@ -82,27 +82,6 @@ static unsigned char parport_sunbpp_read_data(struct parport *p)
 	return sbus_readb(&regs->p_dr);
 }
 
-#if 0
-static void control_pc_to_sunbpp(struct parport *p, unsigned char status)
-{
-	struct bpp_regs __iomem *regs = (struct bpp_regs __iomem *)p->base;
-	unsigned char value_tcr = sbus_readb(&regs->p_tcr);
-	unsigned char value_or = sbus_readb(&regs->p_or);
-
-	if (status & PARPORT_CONTROL_STROBE) 
-		value_tcr |= P_TCR_DS;
-	if (status & PARPORT_CONTROL_AUTOFD) 
-		value_or |= P_OR_AFXN;
-	if (status & PARPORT_CONTROL_INIT) 
-		value_or |= P_OR_INIT;
-	if (status & PARPORT_CONTROL_SELECT) 
-		value_or |= P_OR_SLCT_IN;
-
-	sbus_writeb(value_or, &regs->p_or);
-	sbus_writeb(value_tcr, &regs->p_tcr);
-}
-#endif
-
 static unsigned char status_sunbpp_to_pc(struct parport *p)
 {
 	struct bpp_regs __iomem *regs = (struct bpp_regs __iomem *)p->base;
diff --git a/include/linux/spi/eeprom.h b/include/linux/spi/eeprom.h
index 306e7b1c69ed..403e007aef68 100644
--- a/include/linux/spi/eeprom.h
+++ b/include/linux/spi/eeprom.h
@@ -20,6 +20,16 @@ struct spi_eeprom {
 #define	EE_ADDR3	0x0004			/* 24 bit addrs */
 #define	EE_READONLY	0x0008			/* disallow writes */
 
+	/*
+	 * Certain EEPROMS have a size that is larger than the number of address
+	 * bytes would allow (e.g. like M95040 from ST that has 512 Byte size
+	 * but uses only one address byte (A0 to A7) for addressing.) For
+	 * the extra address bit (A8, A16 or A24) bit 3 of the instruction byte
+	 * is used. This instruction bit is normally defined as don't care for
+	 * other AT25 like chips.
+	 */
+#define EE_INSTR_BIT3_IS_ADDR	0x0010
+
 	/* for exporting this chip's data to other kernel code */
 	void (*setup)(struct memory_accessor *mem, void *context);
 	void *context;