This means switching to the tty refcounted model so that we will not
race with interrupts.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: user-mode-linux-devel@lists.sourceforge.net
Signed-off-by: Richard Weinberger <richard@nod.at>
And use count from there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: user-mode-linux-devel@lists.sourceforge.net
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull final kmap_atomic cleanups from Cong Wang:
"This should be the final round of cleanup, as the definitions of enum
km_type finally get removed from the whole tree. The patches have
been in linux-next for a long time."
* 'kmap_atomic' of git://github.com/congwang/linux:
pipe: remove KM_USER0 from comments
vmalloc: remove KM_USER0 from comments
feature-removal-schedule.txt: remove kmap_atomic(page, km_type)
tile: remove km_type definitions
um: remove km_type definitions
asm-generic: remove km_type definitions
avr32: remove km_type definitions
frv: remove km_type definitions
powerpc: remove km_type definitions
arm: remove km_type definitions
highmem: remove the deprecated form of kmap_atomic
tile: remove usage of enum km_type
frv: remove the second parameter of kmap_atomic_primary()
jbd2: remove the second argument of kmap_atomic
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Convert the existing uses of random_ether_addr to
the new eth_random_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 616c310e83.
(Move PREEMPT_RCU preemption to switch_to() invocation).
Testing by Sasha Levin <levinsasha928@gmail.com> showed that this
can result in deadlock due to invoking the scheduler when one of
the runqueue locks is held. Because this commit was simply a
performance optimization, revert it.
Reported-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Does block_sigmask() + tracehook_signal_handler(); called when
sigframe has been successfully built. All architectures converted
to it; block_sigmask() itself is gone now (merged into this one).
I'm still not too happy with the signature, but that's a separate
story (IMO we need a structure that would contain signal number +
siginfo + k_sigaction, so that get_signal_to_deliver() would fill one,
signal_delivered(), handle_signal() and probably setup...frame() -
take one).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Only 3 out of 63 do not. Renamed the current variant to __set_current_blocked(),
added set_current_blocked() that will exclude unblockable signals, switched
open-coded instances to it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
replace boilerplate "should we use ->saved_sigmask or ->blocked?"
with calls of obvious inlined helper...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
first fruits of ..._restore_sigmask() helpers: now we can take
boilerplate "signal didn't have a handler, clear RESTORE_SIGMASK
and restore the blocked mask from ->saved_mask" into a common
helper. Open-coded instances switched...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull second pile of signal handling patches from Al Viro:
"This one is just task_work_add() series + remaining prereqs for it.
There probably will be another pull request from that tree this
cycle - at least for helpers, to get them out of the way for per-arch
fixes remaining in the tree."
Fix trivial conflict in kernel/irq/manage.c: the merge of Andrew's pile
had brought in commit 97fd75b7b8 ("kernel/irq/manage.c: use the
pr_foo() infrastructure to prefix printks") which changed one of the
pr_err() calls that this merge moves around.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
keys: kill task_struct->replacement_session_keyring
keys: kill the dummy key_replace_session_keyring()
keys: change keyctl_session_to_parent() to use task_work_add()
genirq: reimplement exit_irq_thread() hook via task_work_add()
task_work_add: generic process-context callbacks
avr32: missed _TIF_NOTIFY_RESUME on one of do_notify_resume callers
parisc: need to check NOTIFY_RESUME when exiting from syscall
move key_repace_session_keyring() into tracehook_notify_resume()
TIF_NOTIFY_RESUME is defined on all targets now
kill_off_processes() might miss a valid process, this is because checking
for process->mm is not enough. Process' main thread may exit or detach
its mm via use_mm(), but other threads may still have a valid mm.
To catch this we use find_lock_task_mm(), which walks up all threads and
returns an appropriate task (with task lock held).
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checking for task->mm is dangerous as ->mm might disappear (exit_mm()
assigns NULL under task_lock(), so tasklist lock is not enough).
We can't use get_task_mm()/mmput() pair as mmput() might sleep, so let's
take the task lock while we care about its mm.
Note that we should also use find_lock_task_mm() to check all process'
threads for a valid mm, but for uml we'll do it in a separate patch.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Traversing the tasks requires holding tasklist_lock, otherwise it is
unsafe.
p.s. However, I'm not sure that calling os_kill_ptraced_process() in the
atomic context is correct. It seem to work, but please take a closer
look.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit d065bd810b ("mm: retry page fault when blocking on disk
transfer") and commit 37b23e0525 ("x86,mm: make pagefault killable")
introduced changes into the x86 pagefault handler for making the page
fault handler retryable as well as killable.
These changes reduce the mmap_sem hold time, which is crucial during OOM
killer invocation.
Port these changes to um.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull kbuild updates from Michal Marek.
Fixed up nontrivial merge conflict in Makefile as per Stephen Rothwell
and linux-next (and trivial arch/sparc/Makefile changes due to removed
sparc32 logic).
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
mips: Fix KBUILD_CPPFLAGS definition
kbuild: fix ia64 link
kbuild: document KBUILD_LDS, KBUILD_VMLINUX_{INIT,MAIN} and LDFLAGS_vmlinux
kbuild: link of vmlinux moved to a script
kbuild: refactor final link of sparc32
kbuild: drop unused KBUILD_VMLINUX_OBJS from top-level Makefile
kbuild: Makefile: remove unnecessary check for m68knommu ARCH
Pull KVM changes from Avi Kivity:
"Changes include additional instruction emulation, page-crossing MMIO,
faster dirty logging, preventing the watchdog from killing a stopped
guest, module autoload, a new MSI ABI, and some minor optimizations
and fixes. Outside x86 we have a small s390 and a very large ppc
update.
Regarding the new (for kvm) rebaseless workflow, some of the patches
that were merged before we switch trees had to be rebased, while
others are true pulls. In either case the signoffs should be correct
now."
Fix up trivial conflicts in Documentation/feature-removal-schedule.txt
arch/powerpc/kvm/book3s_segment.S and arch/x86/include/asm/kvm_para.h.
I suspect the kvm_para.h resolution ends up doing the "do I have cpuid"
check effectively twice (it was done differently in two different
commits), but better safe than sorry ;)
* 'next' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (125 commits)
KVM: make asm-generic/kvm_para.h have an ifdef __KERNEL__ block
KVM: s390: onereg for timer related registers
KVM: s390: epoch difference and TOD programmable field
KVM: s390: KVM_GET/SET_ONEREG for s390
KVM: s390: add capability indicating COW support
KVM: Fix mmu_reload() clash with nested vmx event injection
KVM: MMU: Don't use RCU for lockless shadow walking
KVM: VMX: Optimize %ds, %es reload
KVM: VMX: Fix %ds/%es clobber
KVM: x86 emulator: convert bsf/bsr instructions to emulate_2op_SrcV_nobyte()
KVM: VMX: unlike vmcs on fail path
KVM: PPC: Emulator: clean up SPR reads and writes
KVM: PPC: Emulator: clean up instruction parsing
kvm/powerpc: Add new ioctl to retreive server MMU infos
kvm/book3s: Make kernel emulated H_PUT_TCE available for "PR" KVM
KVM: PPC: bookehv: Fix r8/r13 storing in level exception handler
KVM: PPC: Book3S: Enable IRQs during exit handling
KVM: PPC: Fix PR KVM on POWER7 bare metal
KVM: PPC: Fix stbux emulation
KVM: PPC: bookehv: Use lwz/stw instead of PPC_LL/PPC_STL for 32-bit fields
...
Pull timer updates from Thomas Gleixner.
Various trivial conflict fixups in arch Kconfig due to addition of
unrelated entries nearby. And one slightly more subtle one for sparc32
(new user of GENERIC_CLOCKEVENTS), fixed up as per Thomas.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
timekeeping: Fix a few minor newline issues.
time: remove obsolete declaration
ntp: Fix a stale comment and a few stray newlines.
ntp: Correct TAI offset during leap second
timers: Fixup the Kconfig consolidation fallout
x86: Use generic time config
unicore32: Use generic time config
um: Use generic time config
tile: Use generic time config
sparc: Use: generic time config
sh: Use generic time config
score: Use generic time config
s390: Use generic time config
openrisc: Use generic time config
powerpc: Use generic time config
mn10300: Use generic time config
mips: Use generic time config
microblaze: Use generic time config
m68k: Use generic time config
m32r: Use generic time config
...
Pull first series of signal handling cleanups from Al Viro:
"This is just the first part of the queue (about a half of it);
assorted fixes all over the place in signal handling.
This one ends with all sigsuspend() implementations switched to
generic one (->saved_sigmask-based).
With this, a bunch of assorted old buglets are fixed and most of the
missing bits of NOTIFY_RESUME hookup are in place. Two more fixes sit
in arm and um trees respectively, and there's a couple of broken ones
that need obvious fixes - parisc and avr32 check TIF_NOTIFY_RESUME
only on one of two codepaths; fixes for that will happen in the next
series"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (55 commits)
unicore32: if there's no handler we need to restore sigmask, syscall or no syscall
xtensa: add handling of TIF_NOTIFY_RESUME
microblaze: drop 'oldset' argument of do_notify_resume()
microblaze: handle TIF_NOTIFY_RESUME
score: add handling of NOTIFY_RESUME to do_notify_resume()
m68k: add TIF_NOTIFY_RESUME and handle it.
sparc: kill ancient comment in sparc_sigaction()
h8300: missing checks of __get_user()/__put_user() return values
frv: missing checks of __get_user()/__put_user() return values
cris: missing checks of __get_user()/__put_user() return values
powerpc: missing checks of __get_user()/__put_user() return values
sh: missing checks of __get_user()/__put_user() return values
sparc: missing checks of __get_user()/__put_user() return values
avr32: struct old_sigaction is never used
m32r: struct old_sigaction is never used
xtensa: xtensa_sigaction doesn't exist
alpha: tidy signal delivery up
score: don't open-code force_sigsegv()
cris: don't open-code force_sigsegv()
blackfin: don't open-code force_sigsegv()
...
Pull fpu state cleanups from Ingo Molnar:
"This tree streamlines further aspects of FPU handling by eliminating
the prepare_to_copy() complication and moving that logic to
arch_dup_task_struct().
It also fixes the FPU dumps in threaded core dumps, removes and old
(and now invalid) assumption plus micro-optimizes the exit path by
avoiding an FPU save for dead tasks."
Fixed up trivial add-add conflict in arch/sh/kernel/process.c that came
in because we now do the FPU handling in arch_dup_task_struct() rather
than the legacy (and now gone) prepare_to_copy().
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu: drop the fpu state during thread exit
x86, xsave: remove thread_has_fpu() bug check in __sanitize_i387_state()
coredump: ensure the fpu state is flushed for proper multi-threaded core dump
fork: move the real prepare_to_copy() users to arch_dup_task_struct()
Pull UML updates from Richard Weinberger:
"Most changes are bug fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: missing checks of __put_user()/__get_user() return values
um: stub_rt_sigsuspend isn't needed these days anymore
um/x86: merge (and trim) 32- and 64-bit variants of ptrace.h
irq: Remove irq_chip->release()
um: Remove CONFIG_IRQ_RELEASE_METHOD
um: Remove usage of irq_chip->release()
um: Implement um_free_irq()
um: Fix __swp_type()
um: Implement a custom pte_same() function
um: Add BUG() to do_ops()'s error path
um: Remove unused variables
um: bury unused _TIF_RESTORE_SIGMASK
um: wrong sigmask saved in case of multiple sigframes
um: add TIF_NOTIFY_RESUME
um: ->restart_block.fn needs to be reset on sigreturn
guts of saved_sigmask-based sigsuspend/rt_sigsuspend. Takes
kernel sigset_t *.
Open-coded instances replaced with calling it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull smp hotplug cleanups from Thomas Gleixner:
"This series is merily a cleanup of code copied around in arch/* and
not changing any of the real cpu hotplug horrors yet. I wish I'd had
something more substantial for 3.5, but I underestimated the lurking
horror..."
Fix up trivial conflicts in arch/{arm,sparc,x86}/Kconfig and
arch/sparc/include/asm/thread_info_32.h
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
um: Remove leftover declaration of alloc_task_struct_node()
task_allocator: Use config switches instead of magic defines
sparc: Use common threadinfo allocator
score: Use common threadinfo allocator
sh-use-common-threadinfo-allocator
mn10300: Use common threadinfo allocator
powerpc: Use common threadinfo allocator
mips: Use common threadinfo allocator
hexagon: Use common threadinfo allocator
m32r: Use common threadinfo allocator
frv: Use common threadinfo allocator
cris: Use common threadinfo allocator
x86: Use common threadinfo allocator
c6x: Use common threadinfo allocator
fork: Provide kmemcache based thread_info allocator
tile: Use common threadinfo allocator
fork: Provide weak arch_release_[task_struct|thread_info] functions
fork: Move thread info gfp flags to header
fork: Remove the weak insanity
sh: Remove cpu_idle_wait()
...
Sigh, I missed to check which architecture Kconfig files actually
include the core Kconfig file. There are a few which did not. So we
broke them.
Instead of adding the includes to those, we are better off to move the
include to init/Kconfig like we did already with irqs and others.
This does not change anything for the architectures using the old
style periodic timer mode. It just solves the build wreckage there.
For those architectures which use the clock events infrastructure it
moves the include of the core Kconfig file to "General setup" which is
a way more logical place than having it at random locations specified
by the architecture specific Kconfigs.
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Anna-Maria Gleixner <anna-maria@glx-um.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
UML does no longer need CONFIG_IRQ_RELEASE_METHOD.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Instead of using chip->release() we can achieve the same
using a simple wrapper for free_irq().
We have already um_request_irq(), so um_free_irq() is the perfect
counterpart.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
The current __swp_type() function uses a too small bitshift.
Using more than one swap files causes bad pages because
the type bits clash with other page flags.
CC: stable@kernel.org
Analyzed-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
UML uses the _PAGE_NEWPAGE flag to mark pages which are not jet
installed on the host side using mmap().
pte_same() has to ignore this flag, otherwise unuse_pte_range()
is unable to unuse the page because two identical
page tables entries with different _PAGE_NEWPAGE flags would not
match and swapoff() would never return.
CC: stable@kernel.org
Analyzed-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
In case we encounter a bad operation in do_ops() something is really
broken and it's better to BUG().
Signed-off-by: Richard Weinberger <richard@nod.at>
we can't just find oldmask once; if there are multiple signals
and we loop building sigframes for those, ->saved_mask will be
definitely wrong for all but the first one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Historical prepare_to_copy() is mostly a no-op, duplicated for majority of
the architectures and the rest following the x86 model of flushing the extended
register state like fpu there.
Remove it and use the arch_dup_task_struct() instead.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-1-git-send-email-suresh.b.siddha@intel.com
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Move the final link of vmlinux to a script to improve
readability and maintainability of the code.
The Makefile fragments used to link vmlinux has over the
years seen far too many changes and the logic had become
hard to follow.
As the process by nature is serialized there was
nothing gained including this in the Makefile.
"um" has special link requirments - and the
only way to handle this was to hard-code the linking
of "um" in the script.
This was better than trying to modularize it only for the
benefit of "um" anyway.
The shell script has been improved after input from:
Arnaud Lacombe <lacombar@gmail.com>
Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Arnaud Lacombe <lacombar@gmail.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Currently, PREEMPT_RCU readers are enqueued upon entry to the scheduler.
This is inefficient because enqueuing is required only if there is a
context switch, and entry to the scheduler does not guarantee a context
switch.
The commit therefore moves the enqueuing to immediately precede the
call to switch_to() from the scheduler.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Preparatory patch to make the idle thread allocation for secondary
cpus generic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20120420124556.964170564@linutronix.de
Merge reason: development work has dependency on kvm patches merged
upstream.
Conflicts:
Documentation/feature-removal-schedule.txt
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Fix the following gcc complain
arch/um/kernel/skas/mmu.c: In function 'uml_setup_stubs':
arch/um/kernel/skas/mmu.c:106:16: warning: unused variable 'pages' [-Wunused-variable]
Signed-Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
... rather than open-coding the 64bit versions. endian.h has those guys.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
while we can't just use -U$(SUBARCH), we still need to kill idiotic define
(implicit -Di386=1), both for SUBARCH=i386 and SUBARCH=x86/CONFIG_64BIT=n
builds.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When a host stops or suspends a VM it will set a flag to show this. The
watchdog will use these functions to determine if a softlockup is real, or the
result of a suspended VM.
Signed-off-by: Eric B Munson <emunson@mgebm.net>
asm-generic changes Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This has been obsolescent for a while; time for the final push.
In adjacent context, replaced old cpus_* with cpumask_*.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: David S. Miller <davem@davemloft.net> (arch/sparc)
Acked-by: Chris Metcalf <cmetcalf@tilera.com> (arch/tile)
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: linux-hexagon@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: sparclinux@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Pull UML changes from Richard Weinberger:
"Mostly bug fixes and cleanups"
* 'for-linus-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml: (35 commits)
um: Update defconfig
um: Switch to large mcmodel on x86_64
MTD: Relax dependencies
um: Wire CONFIG_GENERIC_IO up
um: Serve io_remap_pfn_range()
Introduce CONFIG_GENERIC_IO
um: allow SUBARCH=x86
um: most of the SUBARCH uses can be killed
um: deadlock in line_write_interrupt()
um: don't bother trying to rebuild CHECKFLAGS for USER_OBJS
um: use the right ifdef around exports in user_syms.c
um: a bunch of headers can be killed by using generic-y
um: ptrace-generic.h doesn't need user.h
um: kill HOST_TASK_PID
um: remove pointless include of asm/fixmap.h from asm/pgtable.h
um: asm-offsets.h might as well come from underlying arch...
um: merge processor_{32,64}.h a bit...
um: switch close_chan() to struct line
um: race fix: initialize delayed_work *before* registering IRQ
um: line->have_irq is never checked...
...
x86_64 UML is unable to load modules if more than 504MiB
of memory are used.
This happens because on x86_64 the UML process has a quite high
start address (typically around 0x6000000).
If UML's memory is larger than 504MiB VMALLOC_START happens to be after
0x8000000. This is no problem unless one loads a module which was built
with R_X86_64_32S relocations.
Symbols with a location > 0x8000000 cannot be used with R_X86_64_32S
To deal with this x86_64 UML has to be compiled with -mcmodel=large
such that no R_X86_64_32S relocations are used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reported-by: 전하늘 <allskyee@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[richard@nod.at: Re-export SUBARCH in arch/um/Makefile]
Signed-off-by: Richard Weinberger <richard@nod.at>
... the same one that controls whether elf_aux.o is included into the
build, bringing the vsyscall_e... into it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
just provide get_current_pid() to the userland side of things
instead of get_current() + manual poking in its results
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
... and switch chan_interrupt() to directly calling close_one_chan(),
so we can lose delay_free_irq argument of close_chan() as well.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
... since chan_interrupt() might schedule it if there's too much
incoming data. Kill task argument of chan_interrupt(), while
we are at it - it's always &line->task.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
put references to in and out chans associated with line into
explicit struct chan * fields in it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
move config-independent parts of initialization into
register_lines(), call setup_one_line() after it instead
of abusing ->init_str.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Current code doesn't update the symlinks in /sys/dev/char when we add/remove
tty lines. Fixing that allows to stop messing with ->valid before the driver
registration, which is a Good Thing(tm) - we shouldn't have it set before we
really have the things set up and ready for line_open().
We need tty_driver available to call tty_{un,}register_device(), so we just
stash a reference to it into struct line_driver.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull parse_chan_pair() call into setup_one_line(), under the mutex.
We really don't want open() to succeed before parse_chan_pair() had
been done (or after it has failed, BTW). We also want "remove con<n>"
to free irqs, etc., same as "config con<n>=none".
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
If two processes are opening the same line, the second to get
into line_open() will decide that it doesn't need to do anything
(correctly) or wait for anything. The latter, unfortunately,
is incorrect - the first opener might not be through yet. We
need to have exclusion covering the entire line_init(), including
the blocking parts. Moreover, the next patch will need to
widen the exclusion on mconsole side of things, also including
the blocking bits, so let's just convert that sucker to mutex...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
make line_setup() act on a separate array of conf strings + default conf,
have lines array initialized explicitly by that data, bury LINE_INIT()
macro from hell.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
As described in commit e6fa16ab9c ("signal: sigprocmask() should do
retarget_shared_pending()") the modification of current->blocked is
incorrect as we need to check whether the signal we're about to block is
pending in the shared queue.
Also, use the new helper function introduced in commit 5e6292c0f2
("signal: add block_sigmask() for adding sigmask to current->blocked")
which centralises the code for updating current->blocked after
successfully delivering a signal and reduces the amount of duplicate
code across architectures. In the past some architectures got this code
wrong, so using this helper function should stop that from happening
again.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we fail to setup the signal stack frame then we don't need to restore
current->blocked because it is not modified by setup_signal_stack_*.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Richard Weinberger <richard@nod.at>
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.
Return state from setup_etheraddr() about returning a random
MAC address or not and check this state in eth_configure().
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit: (29 commits)
audit: no leading space in audit_log_d_path prefix
audit: treat s_id as an untrusted string
audit: fix signedness bug in audit_log_execve_info()
audit: comparison on interprocess fields
audit: implement all object interfield comparisons
audit: allow interfield comparison between gid and ogid
audit: complex interfield comparison helper
audit: allow interfield comparison in audit rules
Kernel: Audit Support For The ARM Platform
audit: do not call audit_getname on error
audit: only allow tasks to set their loginuid if it is -1
audit: remove task argument to audit_set_loginuid
audit: allow audit matching on inode gid
audit: allow matching on obj_uid
audit: remove audit_finish_fork as it can't be called
audit: reject entry,always rules
audit: inline audit_free to simplify the look of generic code
audit: drop audit_set_macxattr as it doesn't do anything
audit: inline checks for not needing to collect aux records
audit: drop some potentially inadvisable likely notations
...
Use evil merge to fix up grammar mistakes in Kconfig file.
Bad speling and horrible grammar (and copious swearing) is to be
expected, but let's keep it to commit messages and comments, rather than
expose it to users in config help texts or printouts.
Every arch calls:
if (unlikely(current->audit_context))
audit_syscall_entry()
which requires knowledge about audit (the existance of audit_context) in
the arch code. Just do it all in static inline in audit.h so that arch's
can remain blissfully ignorant.
Signed-off-by: Eric Paris <eparis@redhat.com>
The audit system previously expected arches calling to audit_syscall_exit to
supply as arguments if the syscall was a success and what the return code was.
Audit also provides a helper AUDITSC_RESULT which was supposed to simplify things
by converting from negative retcodes to an audit internal magic value stating
success or failure. This helper was wrong and could indicate that a valid
pointer returned to userspace was a failed syscall. The fix is to fix the
layering foolishness. We now pass audit_syscall_exit a struct pt_reg and it
in turns calls back into arch code to collect the return value and to
determine if the syscall was a success or failure. We also define a generic
is_syscall_success() macro which determines success/failure based on if the
value is < -MAX_ERRNO. This works for arches like x86 which do not use a
separate mechanism to indicate syscall failure.
We make both the is_syscall_success() and regs_return_value() static inlines
instead of macros. The reason is because the audit function must take a void*
for the regs. (uml calls theirs struct uml_pt_regs instead of just struct
pt_regs so audit_syscall_exit can't take a struct pt_regs). Since the audit
function takes a void* we need to use static inlines to cast it back to the
arch correct structure to dereference it.
The other major change is that on some arches, like ia64, MIPS and ppc, we
change regs_return_value() to give us the negative value on syscall failure.
THE only other user of this macro, kretprobe_example.c, won't notice and it
makes the value signed consistently for the audit functions across all archs.
In arch/sh/kernel/ptrace_64.c I see that we were using regs[9] in the old
audit code as the return value. But the ptrace_64.h code defined the macro
regs_return_value() as regs[3]. I have no idea which one is correct, but this
patch now uses the regs_return_value() function, so it now uses regs[3].
For powerpc we previously used regs->result but now use the
regs_return_value() function which uses regs->gprs[3]. regs->gprs[3] is
always positive so the regs_return_value(), much like ia64 makes it negative
before calling the audit code when appropriate.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: H. Peter Anvin <hpa@zytor.com> [for x86 portion]
Acked-by: Tony Luck <tony.luck@intel.com> [for ia64]
Acked-by: Richard Weinberger <richard@nod.at> [for uml]
Acked-by: David S. Miller <davem@davemloft.net> [for sparc]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [for mips]
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [for ppc]
* 'x86-syscall-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Move <asm/asm-offsets.h> from trace_syscalls.c to asm/syscall.h
x86, um: Fix typo in 32-bit system call modifications
um: Use $(srctree) not $(KBUILD_SRC)
x86, um: Mark system call tables readonly
x86, um: Use the same style generated syscall tables as native
um: Generate headers before generating user-offsets.s
um: Run host archheaders, allow use of host generated headers
kbuild, headers.sh: Don't make archheaders explicitly
x86, syscall: Allow syscall offset to be symbolic
x86, syscall: Re-fix typo in comment
x86: Simplify syscallhdr.sh
x86: Generate system call tables and unistd_*.h from tables
checksyscalls: Use arch/x86/syscalls/syscall_32.tbl as source
x86: Machine-readable syscall tables and scripts to process them
trace: Include <asm/asm-offsets.h> in trace_syscalls.c
x86-64, ia32: Move compat_ni_syscall into C and its own file
x86-64, syscall: Adjust comment spacing and remove typo
kbuild: Add support for an "archheaders" target
kbuild: Add support for installing generated asm headers
frv, h8300, m68k, microblaze, openrisc, score, um and xtensa currently
do not register a CPU device. Add the config option GENERIC_CPU_DEVICES
which causes a generic CPU device to be registered for each present CPU,
and make all these architectures select it.
Richard Weinberger <richard@nod.at> covered UML and suggested using
per_cpu.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
Those two APIs were provided to optimize the calls of
tick_nohz_idle_enter() and rcu_idle_enter() into a single
irq disabled section. This way no interrupt happening in-between would
needlessly process any RCU job.
Now we are talking about an optimization for which benefits
have yet to be measured. Let's start simple and completely decouple
idle rcu and dyntick idle logics to simplify.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
It is assumed that rcu won't be used once we switch to tickless
mode and until we restart the tick. However this is not always
true, as in x86-64 where we dereference the idle notifiers after
the tick is stopped.
To prepare for fixing this, add two new APIs:
tick_nohz_idle_enter_norcu() and tick_nohz_idle_exit_norcu().
If no use of RCU is made in the idle loop between
tick_nohz_enter_idle() and tick_nohz_exit_idle() calls, the arch
must instead call the new *_norcu() version such that the arch doesn't
need to call rcu_idle_enter() and rcu_idle_exit().
Otherwise the arch must call tick_nohz_enter_idle() and
tick_nohz_exit_idle() and also call explicitly:
- rcu_idle_enter() after its last use of RCU before the CPU is put
to sleep.
- rcu_idle_exit() before the first use of RCU after the CPU is woken
up.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The tick_nohz_stop_sched_tick() function, which tries to delay
the next timer tick as long as possible, can be called from two
places:
- From the idle loop to start the dytick idle mode
- From interrupt exit if we have interrupted the dyntick
idle mode, so that we reprogram the next tick event in
case the irq changed some internal state that requires this
action.
There are only few minor differences between both that
are handled by that function, driven by the ts->inidle
cpu variable and the inidle parameter. The whole guarantees
that we only update the dyntick mode on irq exit if we actually
interrupted the dyntick idle mode, and that we enter in RCU extended
quiescent state from idle loop entry only.
Split this function into:
- tick_nohz_idle_enter(), which sets ts->inidle to 1, enters
dynticks idle mode unconditionally if it can, and enters into RCU
extended quiescent state.
- tick_nohz_irq_exit() which only updates the dynticks idle mode
when ts->inidle is set (ie: if tick_nohz_idle_enter() has been called).
To maintain symmetry, tick_nohz_restart_sched_tick() has been renamed
into tick_nohz_idle_exit().
This simplifies the code and micro-optimize the irq exit path (no need
for local_irq_save there). This also prepares for the split between
dynticks and rcu extended quiescent state logics. We'll need this split to
further fix illegal uses of RCU in extended quiescent states in the idle
loop.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
$(KBUILD_SRC) is not defined without O=, use $(srctree).
Reported-and-tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In case we need generated header files for the values in
user-offsets.h, make sure we build generated header files before
user-offsets.s is built.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Run the "archheaders" target for the host architecture, for
architectures (like x86, now) that want to generate some of the
necessary header files.
Add $(HOST_DIR)/include/generated to the include path so we then pick
them up.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This converts the um clocksource to use clocksource_register_hz/khz
This is untested, so any assistance in testing would be appreciated!
CC: Jeff Dike <jdike@addtoit.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
ubd_file_size() cannot use ubd_dev->cow.file because at this time
ubd_dev->cow.file is not initialized.
Therefore, ubd_file_size() will always report a wrong disk size when
COW files are used.
Reading from /dev/ubd* would crash the kernel.
We have to read the correct disk size from the COW file's backing
file.
Signed-off-by: Richard Weinberger <richard@nod.at>
CC: stable@kernel.org
ksyms.c is down to the stuff defined in various USER_OBJS
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
* kill duplicates with drivers/char/Kconfig
* take watchdog one into drivers/watchdog/Kconfig
* take mmapper to arch/um/Kconfig.um
* rename Kconfig.char menu to "UML Character Devices"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
a) exports in gmon_syms.c duplicate kernel/gcov/* ones
b) excluding -pg in vdso compile is not enough - -fprofile-arcs
and -ftest-coverage also needs to be excluded
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
it's x86-only and we have no business playing with it in asm/mmu.h; make
the latter have
struct uml_arch_mm_context arch;
instead of
struct uml_ldt ldt;
and let arch/<subarch>/um/asm/mm_context.h decide what'll be in there.
While we are at it, kill host_ldt.h - it's not needed in part of places
that include it (we want asm/ldt.h in those) and it can be trivially
expanded into the single remaining one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
it's i386-specific; moreover, analogs on other targets have
incompatible interface - PTRACE_GET_THREAD_AREA does exist
elsewhere, but struct user_desc does *not*
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
most of the functions in there are not used in anything that ends up
including that header...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
now we don't mix host and guest signal frame layouts anymore; moreover,
we don't need host's struct sigcontext at all.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
For one thing, we always block the same signals (IRQ ones - IO, WINCH, VTALRM),
so there's no need to pass sa_mask elements in arguments. For another, the
flags depend only on whether it's an IRQ signal or not (we add SA_RESTART
for them).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
We used to generate those, but we hadn't done that for a long
time. No need to bother blocking them for signal handlers.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
only sysdep/sigcontext.h uses it and very few definitions are
actually used. The rest refers to symbols that don't even
exist anymore anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
the only users are arch getreg()/putreg() and it's easier to handle
it there instead of playing with macros from hell
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Move those to sys-.../asm/checksum.h, kill include/asm/checksum.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
It's a plain include of user_constants.h and all (2) users are
including user_constants.h directly prior to that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
It's not x86, where __get_user() is a single dereference; here it's
a single ptrace(2) call in host, which obviously costs a lot more.
IOW, it's cheaper to do copy_{to,from}_user() once than bother with
fields one by one...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
Awhile back I removed all the CONFIG_GENERIC_TIME referecnes as
the last of the non-GENERIC_TIME arches were converted.
However, due to the functionality being important and around for
awhile, there apparently were some out of tree hardware enablement
patches that used it and have since been merged.
This patch removes the remaining instances of GENERIC_TIME.
Singed-off-by: John Stultz <john.stultz@linaro.org>
richard@nod.at:
Fixes:
/usr/lib/gcc/x86_64-linux-gnu/4.4.5/../../../../lib/libc.a(strrchr.o): In function `rindex':
(.text+0x0): multiple definition of `strrchr'
If both STATIC_LINK and UML_NET_VDE are set to "y" libc's strrchr may
clash with the kernel implementation.
This workaround comes originally from Jeff Dike:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=494995#35
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) take subarch-specific stuff to subarch_ptrace()
2) PTRACE_{PEEK,POKE}{TEXT,DATA} is handled by ptrace_request() just fine...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's 32bit-only, not 64bit-only... And while we are at it, it's
set_fpxregs(), not set_fpregs()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Weinberger
Jiri Slaby
Linus Torvalds
Cong Wang
David S. Miller
Theodore Ts'o
Joe Perches
Paul E. McKenney
Al Viro
Anton Vorontsov
Kautuk Consul
Thomas Gleixner
Anna-Maria Gleixner
Suresh Siddha
Sam Ravnborg
Paul E. McKenney
Marcelo Tosatti
Boaz Harrosh
Eric B Munson
Rusty Russell
David Howells
Yong Zhang
Matt Fleming
Danny Kukawka
Eric Paris
Ben Hutchings
Frederic Weisbecker
H. Peter Anvin
H. Peter Anvin
John Stultz
Tejun Heo
Al Viro
John Stultz