Commit Graph

270 Commits

Author SHA1 Message Date
Andrea Paterniani 3b45d6380c spi_imx: full duplex dma corruption bugfix
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads.

Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-19 18:49:58 -08:00
Ned Forrester 393df744e0 pxa2xx_spi: bugfix full duplex dma data corruption
Fixes a data corruption bug in pxa2xx_spi.c when operating in full duplex
mode with DMA and using buffers that overlap.

SPI transmit and receive buffers are allowed to be the same or to overlap.
 However, this driver fails if such overlap is attempted in DMA mode
because it maps the rx and tx buffers in the wrong order.  By mapping
DMA_FROM_DEVICE (read) before DMA_TO_DEVICE (write), it invalidates the
cache before flushing it, thus discarding data which should have been
transmitted.

The patch corrects the order of mapping.  This bug exists in all versions
of pxa2xx_spi.c; similar bugs are in the drivers for two other SPI
controllers (au1500, imx).

A version of this patch has been tested on kernel 2.6.20 using
verification of loopback data with: random transfer length, random
bits-per-word, random positive offsets (both larger and smaller than
transfer length) between the start of the rx and tx buffers, and varying
clock rates.

Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: J. Scott Merritt <merrij3@rpi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>		[2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-19 18:49:58 -08:00
Jean-Christophe Lallemand 50d7d5bf31 atmel_spi: work-around required for new HW bug in AT91SAM9263 Rev.B SPI controller
We're working with an AT91SAM9263 Rev B in our design and I experienced
some inconsistency in spi-based touchscreen usage between our board and
the Atmel evaluation kit we have that runs on a Rev A chip.

The data was apparently delayed by 1 byte and got ridiculous data out of
the touchscreen driver, very strange.  As everything looked normal in
the spi, touchscreen and dma logs, I contacted the Atmel support and
they triggered me on a new HW bug that appeared in the Rev B SPI
controller.

The problem is that the SPI controller on the Rev B needs that the
software reset is performed two times so that it's performed correctly.

Applying the patch below solves the issue on my Rev B board.  I've tested
it as well on my Rev A evaluation kit and it has apparently no unwanted
side effect, things continue to work as expected.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-12 17:17:17 -08:00
Linus Torvalds c813b4e16e Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
  UIO: Fix mapping of logical and virtual memory
  UIO: add automata sercos3 pci card support
  UIO: Change driver name of uio_pdrv
  UIO: Add alignment warnings for uio-mem
  Driver core: add bus_sort_breadthfirst() function
  NET: convert the phy_device file to use bus_find_device_by_name
  kobject: Cleanup kobject_rename and !CONFIG_SYSFS
  kobject: Fix kobject_rename and !CONFIG_SYSFS
  sysfs: Make dir and name args to sysfs_notify() const
  platform: add new device registration helper
  sysfs: use ilookup5() instead of ilookup5_nowait()
  PNP: create device attributes via default device attributes
  Driver core: make bus_find_device_by_name() more robust
  usb: turn dev_warn+WARN_ON combos into dev_WARN
  debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
  debug: Introduce a dev_WARN() function
  sysfs: fix deadlock
  device model: Do a quickcheck for driver binding before doing an expensive check
  Driver core: Fix cleanup in device_create_vargs().
  Driver core: Clarify device cleanup.
  ...
2008-10-16 12:40:26 -07:00
Linus Torvalds 8ef50901d3 Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (51 commits)
  [ARM] 5308/1: Fix Viper ISA IRQ handling
  [ARM] 5307/1: pxa: fix CM-X2XX PCMCIA build error
  [ARM] 5306/1: pxa: fix build error on CM-X270
  [ARM] 5302/1: ARM: OMAP: Revert omap3 WDT changes to avoid merge conflict
  [ARM] 5305/1: ARM: OMAP: Fix compile of McBSP by removing unnecessary check
  [ARM] 5301/1: ARM: OMAP: Add missing irq defines
  ARM: OMAP3: Add default kernel config for OMAP LDP
  ARM: OMAP3: Add basic board support for OMAP LDP
  ARM: OMAP3: Defconfig for the Gumstix Overo board (rev 3)
  ARM: OMAP3: Add support for the Gumstix Overo board (rev 3)
  ARM: OMAP3: Add Beagle defconfig
  ARM: OMAP3: Add minimal Beagle board support
  ARM: OMAP3: Add minimal omap3430 support
  ARM: OMAP2: Fix sparse, checkpatch warnings in OMAP2/3 IRQ code
  ARM: OMAP: Fixes to omap_mcbsp_request function
  ARM: OMAP: Add support for OMAP2430 in McBSP
  ARM: OMAP: Add support for McBSP devices 3 - 5 on 34xx
  ARM: OMAP: Allocate McBSP devices dynamically
  Fix sections for omap-mcbsp platform driver
  [ARM] S3C24XX: Additional include moves
  ...
2008-10-16 11:25:32 -07:00
David Brownell 673c0c0038 spi: core and gpio expanders use subsys_init
Make the SPI external GPIO expander drivers register themselves at
subsys_initcall() time when they're statically linked, and make the SPI
core do its driver model initialization earlier so that's safe.

SOC-integrated GPIOs are available starting very early -- often before
initcalls start to run, or earily in arch_initcall() at latest -- so this
improves consistency, letting more subsystems rely on GPIOs being usable
by their own subsys_initcall() code.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:38 -07:00
Lennert Buytenhek 2bec19feab orion_spi: handle 88F6183 erratum
Add support to orion_spi for the 88F6183 ARM SoC by adding code to work
around a 6183-specific erratum.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:38 -07:00
Vernon Sauder f1f640a9c1 pxa2xx_spi: fix chip_info defaults and documentation.
Make the chip info structure data optional by providing reasonable
defaults.  Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.

DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.

Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:38 -07:00
Guennadi Liakhovetski 65a00a2065 pxa2xx_spi: minor cleanup
Minor fixes: remove redundant local variable initialization, fix "can not"
to what I _think_ is a preferred spelling, output IRQ number if requesting
it failed.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:38 -07:00
Ben Dooks cf46b973f7 spi_s3c24xx: pin configuration updates
Add a pin configuration callback for the s3c24xx SPI driver, as there are
several options depending on the channel and the chip in use.

This is needed as the controller may not have been setup by the initial
bootloader and the fact that the SPI controller gets reset over
suspend/resume into slave mode but the GPIO function registers do not.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:38 -07:00
Vernon Sauder f9b90e39cb spi: simplify spi_write_then_read()
Modify spi_write_then_read() to use one transfer.  This speeds up all
callers, and is a minor code shrink.

Signed-off-by: Vernon Sauder <Vernon.Sauder@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:38 -07:00
Kumar Gala 62f9e8f15a mpc52xx_psc_spi: remove code associated with !CONFIG_PPC_MERGE
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16 11:21:38 -07:00
Greg Kroah-Hartman a9b12619f7 device create: misc: convert device_create_drvdata to device_create
Now that device_create() has been audited, rename things back to the
original call to be sane.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-16 09:24:43 -07:00
Benjamin Herrenschmidt 6dc6472581 Merge commit 'origin'
Manual fixup of conflicts on:

	arch/powerpc/include/asm/dcr-regs.h
	drivers/net/ibm_newemac/core.h
2008-10-15 11:31:54 +11:00
Russell King 7e69a8c4d0 Merge branch 's3c-move' into devel
Conflicts:

	arch/arm/mach-versatile/core.c
2008-10-14 22:24:51 +01:00
Russell King b6825d2df5 Merge branch 'omap-all' into devel
Conflicts:

	arch/arm/mach-omap2/gpmc.c
	arch/arm/mach-omap2/irq.c
2008-10-14 22:24:42 +01:00
Grant Likely a897ea13f7 powerpc/mpc5200: fix build warnings on mpc52xx_psc_spi driver
The register definitions have been changed for the mpc5200 PSC ports
to cover some of the changes in the mpc5200b.  One change is that the
ccr register is now a u32 instead of a u16.  However, for the purposes
of this driver we want to continue to use 16 bit access to avoid
changing the existing (working) behaviour.

This patch allows the driver to continue to do 16 bit accesses without
the compiler complaining about it.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-10-08 09:02:11 -06:00
Lennert Buytenhek f2fe1638f6 orion_spi: fix handling of default transfer speed
Accept zero (the default!) as a per-transfer clock speed override.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-03 18:22:18 -07:00
Mike Rapoport 20b918dc77 pxa2xx_spi: fix build breakage
This patch fixes a build error in the pxa2xx-spi driver,
introduced by commit 7e96445533
("pxa2xx_spi: dma bugfixes")

  CC      drivers/spi/pxa2xx_spi.o
drivers/spi/pxa2xx_spi.c: In function 'map_dma_buffers':
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c: In function 'pump_transfers':
drivers/spi/pxa2xx_spi.c:897: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'

[dbrownell@users.sourceforge.net: fix warning too ]

Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-01 12:31:12 -07:00
Ben Dooks 42cde4309b spi_s3c24xx: fix section warning
Fix the section mismatch warning generated by the incorrect naming of
s3c24xx_spidrv which should be s3c24xx_spi_driver:

WARNING: drivers/spi/spi_s3c24xx.o(.data+0x4):
  Section mismatch in reference from the variable s3c24xx_spidrv
  to the (unknown reference) .exit.text:(unknown)

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-13 14:41:52 -07:00
Ned Forrester 7e96445533 pxa2xx_spi: dma bugfixes
Fixes two DMA bugs in the pxa2xx_spi driver.  The first bug is in all
versions of this driver; the second was introduced in the 2.6.20 kernel,
and prevents using the driver with chips like m25p16 flash (which can
issue large DMA reads).

 1. Zero length transfers are permitted for use to insert timing,
    but pxa2xx_spi.c will fail if this is requested in DMA mode.
    Fixed by using programmed I/O (PIO) mode for such transfers.

 2. Transfers larger than 8191 are not permitted in DMA mode.  A
    test for length rejects all large transfers regardless of DMA
    or PIO mode.  Worked around by rejecting only large transfers
    with DMA mapped buffers, and forcing all other transfers
    larger than 8191 to use PIO mode.  A rate limited warning is
    issued for DMA transfers forced to PIO mode.

This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20.  An additional patch would be
required for older kernels, but those versions are very buggy anyway.

Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-13 14:41:52 -07:00
Ned Forrester 8423597d67 pxa2xx_spi: chipselect bugfixes
Fixes several chipselect bugs in the pxa2xx_spi driver.  These bugs are in
all versions of this driver and prevent using it with chips like m25p16
flash.

 1. The spi_transfer.cs_change flag is handled too early:
    before spi_transfer.delay_usecs applies, thus making the
    delay ineffective at holding chip select.

 2. spi_transfer.delay_usecs is ignored on the last transfer
    of a message (likewise not holding chipselect long enough).

 3. If spi_transfer.cs_change is set on the last transfer, the
    chip select is always disabled, instead of the intended
    meaning: optionally holding chip select enabled for the
    next message.

Those first three bugs were fixed with a relocation of delays
and chip select de-assertions.

 4. If a message has the cs_change flag set on the last transfer,
    and had the chip select stayed enabled as requested (see 3,
    above), it would not have been disabled if the next message is
    for a different chip.  Fixed by dropping chip select regardless
    of cs_change at end of a message, if there is no next message
    or if the next message is for a different chip.

This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20.  An additional patch would be
required for older kernels, but those versions are very buggy anyway.

Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-13 14:41:51 -07:00
Peter Korsgaard aa77d96ba9 spi_mpc83xx: reject invalid transfer sizes
Error out on transfer length != multiple of bytes per word with -EINVAL.
Fixes a buffer overrun crash if length < bytes per word.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-13 14:41:51 -07:00
Peter Korsgaard 53604dbe13 spi_mpc83xx: fix clockrate calculation for low speed
Commit a61f5345 (spi_mpc83xx clockrate fixes) broke clockrate calculation
for low speeds.  SPMODE_DIV16 should be set if the divider is higher than
64, not only if the divider gets clipped to 1024.

Furthermore, the clipping check was off by a factor 16 as well.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-13 14:41:51 -07:00
Russell King 55c381e489 [ARM] omap: convert OMAP drivers to use ioremap()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-05 17:02:30 +01:00
Russell King e5480b7397 [ARM] omap: remove an io_v2p() usage
When omap_udc is also incorporated, this macro will no longer be used.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-05 17:02:29 +01:00
David Brownell e48880e02e spi: bugfix spi_add_device() with duplicate chipselects
When reviewing a recent patch I noticed a potential trouble spot in the
registration of new SPI devices.  The SPI master driver is told to set
the device up before adding it to the driver model, so that it's always
properly set up when probe() is called.  (This is important, because in
the case of inverted chipselects, this device can make the bus misbehave
until it's properly deselected.  It's got to be set up even if no driver
binds to the device.)

The trouble spot is that it doesn't first verify that no other device
has been added using that chipselect.  If such a device has been added,
its configuration gets trashed.  (Fortunately this has not been a common
error!)

The fix here adds an explicit check, and a mutex to protect the relevant
critical region.

[akpm@linux-foundation.org: make the lock local to spi_add_device()]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-15 08:35:44 -07:00
Russell King a09e64fbc0 [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
This just leaves include/asm-arm/plat-* to deal with.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:55:48 +01:00
Russell King 4fb8af10d0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes 2008-08-07 09:55:03 +01:00
Russell King be50972935 [ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-08-07 09:40:08 +01:00
Shadi Ammouri 60cadec9da spi: new orion_spi driver
This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs.  It currently supports only one slave, which must use SPI
mode 0.

[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-05 14:33:46 -07:00
Gerard Kam dc329442b9 atmel_spi: fix hang due to missed interrupt
For some time my at91sam9260 board with JFFS2 on serial flash (m25p80)
would hang when accessing the serial flash and SPI bus.  Slowing the SPI
clock down to 9 MHz reduced the occurrence of the hang from "always"
during boot to a nuisance level that allowed other SW development to
continue.  Finally had to address this issue when an application stresses
the I/O to always cause a hang.

Hang seems to be caused by a missed SPI interrupt, so that the task ends
up waiting forever after calling spi_sync().  The fix has 2 parts.  First
is to halt the DMA engine before the "current" PDC registers are loaded.
This ensures that the "next" registers are loaded before the DMA operation
takes off.  The second part of the fix is a kludge that adds a
"completion" interrupt in case the ENDRX interrupt for the last segment of
the DMA chaining operation was missed.

The patch allows the SPI clock for the serial flash to be increased from 9
MHz to 15 MHz (or more?).  No hangs or SPI overruns were encountered.

Haavard: while this patch does indeed improve things, I still see overruns
and CRC errors on my NGW100 board when running the DataFlash at 10 MHz.
However, I think some improvement is better than nothing, so I'm passing
this on for inclusion in 2.6.27.

Signed-off-by: Gerard Kam <gerardk5@verizon.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-04 16:58:45 -07:00
Ben Dooks 5aa6cf302c spi: S3C24XX: reset register status on resume.
Fix a bug in the spi_s3c24xx driver where it does not reset the registers
of the hardware when resuming from suspend (this block has been reset over
suspend).

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-08-04 16:58:45 -07:00
Ben Dooks cb1d0a7a5d spi_s3c24xx: really assign busnum
The original "Pass the bus number we expect the S3C24XX SPI driver to
attach to via the platform data." [1] patch was mis-sent, and missed two
important parts of the diff, which was to actually set the bus_num field
and add the relevant field to the platform data.

The previous commit 50f426b55d promised to
add a bus_num field, but failed to include the two hunks that added this
field to include/asm-arm/arch-s3c2410/spi.h and then pass it to the spi
core when creating the new master field in drivers/spi/spi_s3c24xx.c.

[1] git commit 50f426b55d

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-28 16:30:21 -07:00
Luotao Fu 9a7867e1b3 mpc52xx_psc_spi: fix block transfer
The block transfer routine in the mpc52xx psc spi driver misinterpret
the datasheet.  According to the processor datasheet the chipselect is
held as long as the EOF is not written.

Theoretically blocks of any sizes can be transferred in this way.  The
old routine however writes an EOF after every word, which has the size
of size_of_word.  This makes the transfer slow.

Also fixed some duplicate code.

Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>		[2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-28 16:30:21 -07:00
Benjamin Herrenschmidt d65d830ca0 Merge commit 'gcl/gcl-next' 2008-07-28 16:30:40 +10:00
FUJITA Tomonori 8d8bb39b9e dma-mapping: add the device argument to dma_mapping_error()
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:

This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).

I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread).  So I
CC'ed this to KVM camp.  Comments are appreciated.

A pointer to dma_mapping_ops to struct dev_archdata is added.  If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it.  If it's
NULL, the system-wide dma_ops pointer is used as before.

If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging).  It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.

The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations.  So x86 can't have dma_mapping_ops per
device.  Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.

The first patch adds the device argument to dma_mapping_error.  The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.

This patch:

dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations.  So we can't have dma_mapping_ops per device.

Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function.  x86 IOMMUs use device
argument.

[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-26 12:00:03 -07:00
Grant Likely dc87c98e8f spi: split up spi_new_device() to allow two stage registration.
spi_new_device() allocates and registers an spi device all in one swoop.
If the driver needs to add extra data to the spi_device before it is
registered, then this causes problems.  This is needed for OF device
tree support so that the SPI device tree helper can add a pointer to
the device node after the device is allocated, but before the device
is registered.  OF aware SPI devices can then retrieve data out of the
device node to populate a platform data structure.

This patch splits the allocation and registration portions of code out
of spi_new_device() and creates two new functions; spi_alloc_device()
and spi_register_device().  spi_new_device() is modified to use the new
functions for allocation and registration.  None of the existing users
of spi_new_device() should be affected by this change.

Drivers using the new API can forego the use of spi_board_info
structure to describe the device layout and populate data into the
spi_device structure directly.

This change is in preparation for adding an OF device tree parser to
generate spi_devices based on data in the device tree.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
2008-07-25 22:34:29 -04:00
Jan Nikitenko bbe48ecc7f spi: au1550_spi: improve pio transfer mode
Improve PIO transfer mode of au1550 spi controller by continuing of spi
transfer, instead of aborting transfer when transmit underflow interrupt
occurrs.

Verified by oscilloscope that the spi clock pauses on trasmit underflow,
so transfer continuation is perfectly valid even though au1550 datasheet
says that on tx underflow zeroes will be transfered.

Also make some error messages more specific.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Manuel Lauss 3a93a159c6 spi: au1550_spi: proper platform device
Remove the Au1550 resource table and instead extract MMIO/IRQ/DMA
resources from platform resource information like any well-behaved
platform driver.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Alan Cox 4ef754b7d7 spidev: BKL removal
Another step to removing ->ioctl and to removing the BKL

[dbrownell@users.sourceforge.net: take final step; BKL not needed]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Grant Likely 102eb97564 spi: make spi_board_info.modalias a char array
Currently, 'modalias' in the spi_device structure is a 'const char *'.
The spi_new_device() function fills in the modalias value from a passed in
spi_board_info data block.  Since it is a pointer copy, the new spi_device
remains dependent on the spi_board_info structure after the new spi_device
is registered (no other fields in spi_device directly depend on the
spi_board_info structure; all of the other data is copied).

This causes a problem when dynamically propulating the list of attached
SPI devices.  For example, in arch/powerpc, the list of SPI devices can be
populated from data in the device tree.  With the current code, the device
tree adapter must kmalloc() a new spi_board_info structure for each new
SPI device it finds in the device tree, and there is no simple mechanism
in place for keeping track of these allocations.

This patch changes modalias from a 'const char *' to a fixed char array.
By copying the modalias string instead of referencing it, the dependency
on the spi_board_info structure is eliminated and an outside caller does
not need to maintain a separate spi_board_info allocation for each device.

If searched through the code to the best of my ability for any references
to modalias which may be affected by this change and haven't found
anything.  It has been tested with the lite5200b platform in arch/powerpc.

[dbrownell@users.sourceforge.net: cope with linux-next changes: KOBJ_NAME_LEN obliterated, etc]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Robert P. J. Day 6291fe2abc SPI Kconfig simplifications
Use "if SPI_MASTER" to remove numerous dependencies.

[dbrownell@users.sourceforge.net: remove a couple now-needless EXPERIMENTAL dependencies too]
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Roel Kluin 166a375b65 xilinx_spi: test below 0 on unsigned irq in xilinx_spi_probe()
xilinx_spi->irq is unsigned, so the test fails

Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrei Konovalov <akonovalov@ru.mvista.com>
Cc: Yuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Chen Gong a61f5345eb spi: spi_mpc83xx clockrate fixes
This updates the SPI clock rate calculations for the spi_mpc83xx driver.
Some boundary conditions were wrong, and in several cases divide-by-16
wasn't always needed

Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:30 -07:00
Greg Kroah-Hartman 695794ae0c Driver Core: add ability for class_find_device to start in middle of list
This mirrors the functionality that driver_find_device has as well.

We add a start variable, and all callers of the function are fixed up at
the same time.

The block layer will be using this new functionality in a follow-on
patch.


Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-07-21 21:54:47 -07:00
David Brownell 3d81252ddb device create: spi: convert device_create to device_create_drvdata
Switch over to use the shiny new device_create_drvdata() call
instead of the original device_create() calls, so this continues
to work after device_create() is  removed.

Note that this driver never had the race which motivated removing
the original call; it locked correctly.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-07-21 21:54:45 -07:00
Benjamin Herrenschmidt 43d2548bb2 Merge commit '85082fd7cbe3173198aac0eb5e85ab1edcc6352c' into test-build
Manual fixup of:

	arch/powerpc/Kconfig
2008-07-15 15:44:51 +10:00
Benjamin Herrenschmidt 5b0504c0d7 Merge commit 'gcl/gcl-next' 2008-07-15 11:55:27 +10:00
Linus Torvalds 85082fd7cb Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
  [ARM] 5171/1: ep93xx: fix compilation of modules using clocks
  [ARM] 5133/2: at91sam9g20 defconfig file
  [ARM] 5130/4: Support for the at91sam9g20
  [ARM] 5160/1: IOP3XX: gpio/gpiolib support
  [ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
  [ARM] 5084/1: zylonite: Register AC97 device
  [ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
  [ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
  [ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
  [ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
  [ARM] 5144/1: pxaficp_ir: cleanup includes
  [ARM] pxa: remove pxa_set_cken()
  [ARM] pxa: allow clk aliases
  [ARM] Feroceon: don't disable BPU on boot
  [ARM] Orion: LED support for HP mv2120
  [ARM] Orion: add RD88F5181L-FXO support
  [ARM] Orion: add RD88F5181L-GE support
  [ARM] Orion: add Netgear WNR854T support
  [ARM] s3c2410_defconfig: update for current build
  [ARM] Acer n30: Minor style and indentation fixes.
  ...
2008-07-14 16:06:58 -07:00