This reverts two commits:
fda48a0d7a
tcp: bind() fix when many ports are bound
and a follow-on fix for it:
6443bb1fc2
ipv6: Fix inet6_csk_bind_conflict()
It causes problems with binding listening sockets when time-wait
sockets from a previous instance still are alive.
It's too late to keep fiddling with this so late in the -rc
series, and we'll deal with it in net-next-2.6 instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
Port autoselection done by kernel only works when number of bound
sockets is under a threshold (typically 30000).
When this threshold is over, we must check if there is a conflict before
exiting first loop in inet_csk_get_port()
Change inet_csk_bind_conflict() to forbid two reuse-enabled sockets to
bind on same (address,port) tuple (with a non ANY address)
Same change for inet6_csk_bind_conflict()
Reported-by: Gaspar Chilingarov <gasparch@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris got following trace with a linux-next kernel
[ 14.203970] BUG: using smp_processor_id() in preemptible [00000000]
code: avahi-daemon/2093
[ 14.204025] caller is netif_rx+0xfa/0x110
[ 14.204035] Call Trace:
[ 14.204064] [<ffffffff81278fe5>] debug_smp_processor_id+0x105/0x110
[ 14.204070] [<ffffffff8142163a>] netif_rx+0xfa/0x110
[ 14.204090] [<ffffffff8145b631>] ip_dev_loopback_xmit+0x71/0xa0
[ 14.204095] [<ffffffff8145b892>] ip_mc_output+0x192/0x2c0
[ 14.204099] [<ffffffff8145d610>] ip_local_out+0x20/0x30
[ 14.204105] [<ffffffff8145d8ad>] ip_push_pending_frames+0x28d/0x3d0
[ 14.204119] [<ffffffff8147f1cc>] udp_push_pending_frames+0x14c/0x400
[ 14.204125] [<ffffffff814803fc>] udp_sendmsg+0x39c/0x790
[ 14.204137] [<ffffffff814891d5>] inet_sendmsg+0x45/0x80
[ 14.204149] [<ffffffff8140af91>] sock_sendmsg+0xf1/0x110
[ 14.204189] [<ffffffff8140dc6c>] sys_sendmsg+0x20c/0x380
[ 14.204233] [<ffffffff8100ad82>] system_call_fastpath+0x16/0x1b
While current linux-2.6 kernel doesnt emit this warning, bug is latent
and might cause unexpected failures.
ip_dev_loopback_xmit() runs in process context, preemption enabled, so
must call netif_rx_ni() instead of netif_rx(), to make sure that we
process pending software interrupt.
Same change for ip6_dev_loopback_xmit()
Reported-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commit 634a4b20
Allow tnode_get_child_rcu() to be called either under rcu_read_lock()
protection or with RTNL held.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2626419ad5.
It causes regressions for people with IGB cards. Connection
requests don't complete etc. The true cause of the issue is
still not known, but we should sort this out in net-next-2.6
not net-2.6
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in commit 04a0551c87
("loopback: Drop obsolete ip_summed setting") we stopped
setting CHECKSUM_UNNECESSARY in the loopback xmit.
This is because such a setting was a lie since it implies that the
checksum field of the packet is properly filled in.
Instead what happens normally is that CHECKSUM_PARTIAL is set and
skb->csum is calculated as needed.
But this was only happening for TCP data packets (via the
skb->ip_summed assignment done in tcp_sendmsg()). It doesn't
happen for non-data packets like ACKs etc.
Fix this by setting skb->ip_summed in the common non-data packet
constructor. It already is setting skb->csum to zero.
But this reminds us that we still have things like ip_output.c's
ip_dev_loopback_xmit() which sets skb->ip_summed to the value
CHECKSUM_UNNECESSARY, which Herbert's patch teaches us is not
valid. So we'll have to address that at some point too.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits 5051ebd275 and
5051ebd275 ("ipv[46]: udp: optimize unicast RX
path") broke some programs.
After upgrading a L2TP server to 2.6.33 it started to fail, tunnels going up an
down, after the 10th tunnel came up. My modified rp-l2tp uses a global
unconnected socket bound to (INADDR_ANY, 1701) and one connected socket per
tunnel after parameter negotiation.
After ten sockets were open and due to mixed parameters to
udp[46]_lib_lookup2() kernel started to drop packets.
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
check the length of the socket address passed to connect(2).
Check the length of the socket address passed to connect(2). If the
length is invalid, -EINVAL will be returned.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
net/bluetooth/l2cap.c | 3 ++-
net/bluetooth/rfcomm/sock.c | 3 ++-
net/bluetooth/sco.c | 3 ++-
net/can/bcm.c | 3 +++
net/ieee802154/af_ieee802154.c | 3 +++
net/ipv4/af_inet.c | 5 +++++
net/netlink/af_netlink.c | 3 +++
7 files changed, 20 insertions(+), 3 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_read_sock() can have a eat skbs without immediately advancing copied_seq.
This can cause a panic in tcp_collapse() if it is called as a result
of the recv_actor dropping the socket lock.
A userspace program that splices data from a socket to either another
socket or to a file can trigger this bug.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
When cache is unresolved, c->mf[6]c_parent is set to 65535 and
minvif, maxvif are not initialized, hence we must avoid to
parse IIF and OIF.
A second problem can happen when the user dumps a cache entry
where a VIF, that was referenced at creation time, has been
removed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The the rebuild changes the genid which in turn is used at
the hash calculation. Thus if we don't restart and go on with
inserting the rt will happen in wrong chain.
(Fixed Neil's comment about the index passed into the rt_intern_hash)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need in getting it 3 times and gcc isn't smart enough
to understand this himself.
This is just a cleanup before the fix (next patch).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dump is interrupted at the last device in a hash chain and
then continued, "idx" won't get incremented past s_idx, so s_ip_idx
is not reset when moving on to the next device. This means of all
following devices only the last n - s_ip_idx addresses are dumped.
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Taking route's header_len into account, and updating gre device
needed_headroom will give better hints on upper bound of required
headroom. This is useful if the gre traffic is xfrm'ed.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP sessions over IPv4 can get stuck if routers between endpoints
do not fragment packets but implement PMTU instead, and we are using
those routers because of an ICMP redirect.
Setup is as follows
MTU1 MTU2 MTU1
A--------B------C------D
with MTU1 > MTU2. A and D are endpoints, B and C are routers. B and C
implement PMTU and drop packets larger than MTU2 (for example because
DF is set on all packets). TCP sessions are initiated between A and D.
There is packet loss between A and D, causing frequent TCP
retransmits.
After the number of retransmits on a TCP session reaches tcp_retries1,
tcp calls dst_negative_advice() prior to each retransmit. This results
in route cache entries for the peer to be deleted in
ipv4_negative_advice() if the Path MTU is set.
If the outstanding data on an affected TCP session is larger than
MTU2, packets sent from the endpoints will be dropped by B or C, and
ICMP NEEDFRAG will be returned. A and D receive NEEDFRAG messages and
update PMTU.
Before the next retransmit, tcp will again call dst_negative_advice(),
causing the route cache entry (with correct PMTU) to be deleted. The
retransmitted packet will be larger than MTU2, causing it to be
dropped again.
This sequence repeats until the TCP session aborts or is terminated.
Problem is fixed by removing redirected route cache entries in
ipv4_negative_advice() only if the PMTU is expired.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow fib_find_node() to be called either under rcu_read_lock()
protection or with RTNL held.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under NET_DMA, data transfer can grind to a halt when userland issues a
large read on a socket with a high RCVLOWAT (i.e., 512 KB for both).
This appears to be because the NET_DMA design queues up lots of memcpy
operations, but doesn't issue or wait for them (and thus free the
associated skbs) until it is time for tcp_recvmesg() to return.
The socket hangs when its TCP window goes to zero before enough data is
available to satisfy the read.
Periodically issue asynchronous memcpy operations, and free skbs for ones
that have completed, to prevent sockets from going into zero-window mode.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet is marked as lost in case packets == 0, although nothing should be done.
This results in a too early retransmitted packet during recovery in some cases.
This small patch fixes this issue by returning immediately.
Signed-off-by: Lennart Schulte <lennart.schulte@nets.rwth-aachen.de>
Signed-off-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mfc_parent of cache entries is used to index into the vif_table and is
initialised from mfcctl->mfcc_parent. This can take values of to 2^16-1,
while the vif_table has only MAXVIFS (32) entries. The same problem
affects ip6mr.
Refuse invalid values to fix a potential out-of-bounds access. Unlike
the other validity checks, this is checked in ipmr_mfc_add() instead of
the setsockopt handler since its unused in the delete path and might be
uninitialized.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds RFC5082 checks for TTL on received ICMP packets.
It adds some security against spoofed ICMP packets
disrupting GTSM protected sessions.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xfrm_dst keeps a reference to ipv4 rtable entries on each
cached bundle. The only way to renew xfrm_dst when the underlying
route has changed, is to implement dst_check for this. This is
what ipv6 side does too.
The problems started after 87c1e12b5e
("ipsec: Fix bogus bundle flowi") which fixed a bug causing xfrm_dst
to not get reused, until that all lookups always generated new
xfrm_dst with new route reference and path mtu worked. But after the
fix, the old routes started to get reused even after they were expired
causing pmtu to break (well it would occationally work if the rtable
gc had run recently and marked the route obsolete causing dst_check to
get called).
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
route: Fix caught BUG_ON during rt_secret_rebuild_oneshot()
Call rt_secret_rebuild can cause BUG_ON(timer_pending(&net->ipv4.rt_secret_timer)) in
add_timer as there is not any synchronization for call rt_secret_rebuild_oneshot()
for the same net namespace.
Also this issue affects to rt_secret_reschedule().
Thus use mod_timer enstead.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
Some network devices, particularly USB ones, take several seconds to
fully init and appear in the device list.
If the user turned ipconfig on, they are using it for NFS root or some
other early booting purpose. So it makes no sense to just flat out
fail immediately if the device isn't found.
It also doesn't make sense to just jack up the initial wait to
something crazy like 10 seconds.
Instead, poll immediately, and then periodically once a second,
waiting for a usable device to appear. Fail after 12 seconds.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Christian Pellegrin <chripell@fsfe.org>
Commit d218d111 (tcp: Generalized TTL Security Mechanism) added a bug
for TIMEWAIT sockets. We should not test min_ttl for TW sockets.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4957faad (TCPCT part 1g: Responder Cookie => Initiator), part
of TCP_COOKIE_TRANSACTION implementation, forgot to correctly size
synack skb in case user data must be included.
Many thanks to Mika Pentillä for spotting this error.
Reported-by: Penttillä Mika <mika.penttila@ixonos.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added an automatic route cache rebuilding in commit 1080d709fb
but had to correct few bugs. One of the assumption of original patch,
was that entries where kept sorted in a given way.
This assumption is known to be wrong (commit 1ddbcb005c gave an
explanation of this and corrected a leak) and expensive to respect.
Paweł Staszewski reported to me one of his machine got its routing cache
disabled after few messages like :
[ 2677.850065] Route hash chain too long!
[ 2677.850080] Adjust your secret_interval!
[82839.662993] Route hash chain too long!
[82839.662996] Adjust your secret_interval!
[155843.731650] Route hash chain too long!
[155843.731664] Adjust your secret_interval!
[155843.811881] Route hash chain too long!
[155843.811891] Adjust your secret_interval!
[155843.858209] vlan0811: 5 rebuilds is over limit, route caching
disabled
[155843.858212] Route hash chain too long!
[155843.858213] Adjust your secret_interval!
This is because rt_intern_hash() might be fooled when computing a chain
length, because multiple entries with same keys can differ because of
TOS (or mark/oif) bits.
In the rare case the fast algorithm see a too long chain, and before
taking expensive path, we call a helper function in order to not count
duplicates of same routes, that only differ with tos/mark/oif bits. This
helper works with data already in cpu cache and is not be very
expensive, despite its O(N^2) implementation.
Paweł Staszewski sucessfully tested this patch on his loaded router.
Reported-and-tested-by: Paweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6b03a53a (tcp: use limited socket backlog) added the possibility
of dropping frames when backlog queue is full.
Commit d218d111 (tcp: Generalized TTL Security Mechanism) added the
possibility of dropping frames when TTL is under a given limit.
This patch adds new SNMP MIB entries, named TCPBacklogDrop and
TCPMinTTLDrop, published in /proc/net/netstat in TcpExt: line
netstat -s | egrep "TCPBacklogDrop|TCPMinTTLDrop"
TCPBacklogDrop: 0
TCPMinTTLDrop: 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_add_backlog -> __sk_add_backlog
sk_add_backlog_limited -> sk_add_backlog
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make udp adapt to the limited socket backlog change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "Pekka Savola (ipv6)" <pekkas@netcore.fi>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make tcp adapt to the limited socket backlog change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "Pekka Savola (ipv6)" <pekkas@netcore.fi>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipgre_header() can be called with zero daddr when the gre device is
configured as multipoint tunnel and still has the NOARP flag set (which is
typically cleared by the userspace arp daemon). If the NOARP packets are
not dropped, ipgre_tunnel_xmit() will take rt->rt_gateway (= NBMA IP) and
use that for route look up (and may lead to bogus xfrm acquires).
The multicast address check is removed as sending to multicast group should
be ok. In fact, if gre device has a multicast address as destination
ipgre_header is always called with multicast address.
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I merged the bundle creation code, I introduced a bogus
flowi value in the bundle. Instead of getting from the caller,
it was instead set to the flow in the route object, which is
totally different.
The end result is that the bundles we created never match, and
we instead end up with an ever growing bundle list.
Thanks to Jamal for find this problem.
Reported-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update rcu_dereference() primitives to use new lockdep-based
checking. The rcu_dereference() in __in6_dev_get() may be
protected either by rcu_read_lock() or RTNL, per Eric Dumazet.
The rcu_dereference() in __sk_free() is protected by the fact
that it is never reached if an update could change it. Check
for this by using rcu_dereference_check() to verify that the
struct sock's ->sk_wmem_alloc counter is zero.
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <1266887105-1528-5-git-send-email-paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just pass in the entire repl struct. In case of a new table (e.g.
ip6t_register_table), the repldata has been previously filled with
table->name and table->size already (in ip6t_alloc_initial_table).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The macro is replaced by a list.h-like foreach loop. This makes
the code more inspectable.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The macro is replaced by a list.h-like foreach loop. This makes
the code much more inspectable.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
pass mark to all SA lookups to prepare them for when we add code
to have them search.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Eric Dumazet
Jorge Boncompte [DTI2]
Linus Torvalds
Changli Gao
Steven J. Magnani
Tejun Heo
Nicolas Dichtel
Pavel Emelyanov
Patrick McHardy
Timo Teräs
Guenter Roeck
Paul E. McKenney
Lennart Schulte
stephen hemminger
Alexandra Kossovsky
Vitaliy Gusev
Jiri Kosina
Zhu Yi
Herbert Xu
Jan Engelhardt
Jamal Hadi Salim