Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6640
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tips of Loongson's CPU hotplug:
1, To fully shutdown a core in Loongson 3, the target core should go to
CKSEG1 and flush all L1 cache entries at first. Then, another core
(usually Core 0) can safely disable the clock of the target core. So
play_dead() call loongson3_play_dead() via CKSEG1 (both uncached and
unmmaped).
2, The default clocksource of Loongson is MIPS. Since clock source is a
global device, timekeeping need the CP0' Count registers of each core
be synchronous. Thus, when a core is up, we use a SMP_ASK_C0COUNT IPI
to ask Core-0's Count.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6639
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IPI registers of Loongson-3 include IPI_SET, IPI_CLEAR, IPI_STATUS,
IPI_EN and IPI_MAILBOX_BUF. Each bit of IPI_STATUS indicate a type of
IPI and IPI_EN indicate whether the IPI is enabled. The sender write 1
to IPI_SET bits generate IPIs in IPI_STATUS, and receiver write 1 to
bits of IPI_CLEAR to clear IPIs. IPI_MAILBOX_BUF are used to deliver
more information about IPIs.
Why we change code in arch/mips/loongson/common/setup.c?
If without this change, when SMP configured, system cannot boot since
it hang at printk() in cgroup_init_early(). The root cause is:
console_trylock()
\-->down_trylock(&console_sem)
\-->raw_spin_unlock_irqrestore(&sem->lock, flags)
\-->_raw_spin_unlock_irqrestore()(SMP/UP have different versions)
\-->__raw_spin_unlock_irqrestore() (following is the SMP case)
\-->do_raw_spin_unlock()
\-->arch_spin_unlock()
\-->nudge_writes()
\-->mb()
\-->wbflush()
\-->__wbflush()
In previous code __wbflush() is initialized in plat_mem_setup(), but
cgroup_init_early() is called before plat_mem_setup(). Therefore, In
this patch we make changes to avoid boot failure.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6638
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Added Kconfig options include: Loongson-3 CPU and machine definition,
CPU cache features, UEFI-like firmware interface (LEFI), HT-linked PCI,
and swiotlb support.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6637
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson doesn't support DMA address above 4GB traditionally. If memory
is more than 4GB, CONFIG_SWIOTLB and ZONE_DMA32 should be selected. In
this way, DMA pages are allocated below 4GB preferably. However, if low
memory is not enough, high pages are allocated and swiotlb is used for
bouncing.
Moreover, we provide a platform-specific dma_map_ops::set_dma_mask() to
set a device's dma_mask and coherent_dma_mask. We use these masks to
distinguishes an allocated page can be used for DMA directly, or need
swiotlb to bounce.
Recently, we found that 32-bit DMA isn't a hardware bug, but a hardware
configuration issue. So, latest firmware has enable the DMA support as
high as 40-bit. To support all-memory DMA for all devices (besides the
Loongson platform limit, there are still some devices have their own
DMA32 limit), and also to be compatible with old firmware, we keep use
swiotlb.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6636
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson family machines has three types of serial port: PCI UART, LPC
UART and CPU internal UART. Loongson-2E and parts of Loongson-2F based
machines use PCI UART; most Loongson-2F based machines use LPC UART;
Loongson-2G/3A has both LPC and CPU UART but usually use CPU UART.
Port address of UARTs:
CPU UART: REG_BASE + OFFSET;
LPC UART: LIO1_BASE + OFFSET;
PCI UART: PCIIO_BASE + OFFSET.
Since LPC UART are linked in "Local Bus", both CPU UART and LPC UART
are called "CPU provided serial port".
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6635
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IRQ routing path of Loongson-3:
Devices(most) --> I8259 --> HT Controller --> IRQ Routing Table --> CPU
^
|
Device(legacy devices such as UART) --> Bonito ---|
IRQ Routing Table route 32 INTs to CPU's INT0~INT3(IP2~IP5 of CP0), 32
INTs include 16 HT INTs(mostly), 4 PCI INTs, 1 LPC INT, etc. IP6 is used
for IPI and IP7 is used for internal MIPS timer. LOONGSON_INT_ROUTER_*
are IRQ Routing Table registers.
I8259 IRQs are 1:1 mapped to HT1 INTs. LOONGSON_HT1_* are configuration
registers of HT1 controller.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6634
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson family machines use Hyper-Transport bus for inter-core
connection and device connection. The PCI bus is a subordinate
linked at HT1.
With LEFI firmware interface, We don't need fixup for PCI irq routing
(except providing a VBIOS of the integrated GPU).
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6633
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The new UEFI-like firmware interface (LEFI, i.e. Loongson Unified
Firmware Interface) has 3 advantages:
1, Firmware export a physical memory map which is similar to X86's
E820 map, so prom_init_memory() will be more elegant that #ifdef
clauses can be removed.
2, Firmware export a pci irq routing table, we no longer need pci
irq routing fixup in kernel's code.
3, Firmware has a built-in vga bios, and its address is exported,
the linux kernel no longer need an embedded blob.
With the LEFI interface, Loongson-3A/2G and all their successors can use
a unified kernel. All Loongson-based machines support this new interface
except 2E/2F series.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6632
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add four Loongson-3 based machine types:
MACH_LEMOTE_A1004/MACH_LEMOTE_A1201 are laptops;
MACH_LEMOTE_A1101 is mini-itx;
MACH_LEMOTE_A1205 is all-in-one machine.
The most significant differrent between A1004/A1201 and A1101/A1205 is
the laptops have EC but others don't.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6631
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Basic Loongson-3 CPU support include CPU probing and TLB/cache
initializing.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6630
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3 is a multi-core MIPS family CPU, it support MIPS64R2 fully.
Loongson-3 has the same IMP field (0x6300) as Loongson-2.
Loongson-3 has a hardware-maintained cache, system software doesn't
need to maintain coherency.
Loongson-3A is the first revision of Loongson-3, and it is the quad-
core version of Loongson-2G. Loongson-3A has a simplified version named
Loongson-2Gq, the main difference between Loongson-3A/2Gq is 3A has two
HyperTransport controller but 2Gq has only one. HT0 is used for cross-
chip interconnection and HT1 is used to link PCI bus. Therefore, 2Gq
cannot support NUMA but 3A can. For software, Loongson-2Gq is simply
identified as Loongson-3A.
Exsisting Loongson family CPUs:
Loongson-1: Loongson-1A, Loongson-1B, they are 32-bit MIPS CPUs.
Loongson-2: Loongson-2E, Loongson-2F, Loongson-2G, they are 64-bit
single-core MIPS CPUs.
Loongson-3: Loongson-3A(including so-called Loongson-2Gq), they are
64-bit multi-core MIPS CPUs.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6629/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And there are more CPUs or configurations that want to provide special
per-CPU information in /proc/cpuinfo. So I think there needs to be a
hook mechanism, such as a notifier.
This is a first cut only; I need to think about what sort of looking
the notifier needs to have. But I'd appreciate testing on MT hardware!
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6066/
All architecturally defined bits in the FPU implementation register
are read only & unchanging. It contains some implementation-defined
bits but the architecture manual states "This bits are explicitly not
intended to be used for mode control functions" which seems to provide
justification for viewing the register as a whole as unchanging. This
being the case we can simply re-use the value we read at boot rather
than having to re-read it later, and avoid the complexity which that
read entails.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6147/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All architecturally defined bits in the FPU implementation register
are read only & unchanging. It contains some implementation-defined
bits but the architecture manual states "This bits are explicitly not
intended to be used for mode control functions" which seems to provide
justification for viewing the register as a whole as unchanging. This
being the case we can simply re-use the value we read at boot rather
than having to re-read it later, and avoid the complexity which that
read entails.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6144/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If current_cpu_type() is pre-defined in cpu-feature-overrides.h, This
may save about 10k for the compressed kernel image(vmlinuz).
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1901/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sead3-mtd.o is built for obj-y -- and hence this code is always
present. It will never be modular, so using module_init as an alias
for __initcall can be somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
We also fix a missing semicolon, which this change uncovers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: linux-mips@linux-mips.org
Cc: fengguang.wu@intel.com
Patchwork: https://patchwork.linux-mips.org/patch/6412/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-1 is a 32-bit MIPS CPU and Loongson-2/3 are 64-bit MIPS CPUs,
and both Loongson-2/3 has the same PRID IMP filed (0x6300). As a
result, renaming PRID_IMP_LOONGSON1 and PRID_IMP_LOONGSON2 to
PRID_IMP_LOONGSON_32 and PRID_IMP_LOONGSON_64 will make more sense.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6552/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit c24a8a7a99 ("MIPS: Netlogic: Add MSI support for XLP") added
"select ARCH_SUPPORTS_MSI". But the Kconfig symbol ARCH_SUPPORTS_MSI was
already removed in v3.12, so that select is a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6521/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
74K/proAptiv share the same event/cache maps. So it's better to change the
names of the existing mipsxx74Kcore_[event|cache]_map.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Reviewed-by: Markos Chandras <Markos.Chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/6526/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The HAVE_PWM symbol is only for legacy platforms that provide the PWM
API without using the generic framework. The jz4740 platform uses the
generic PWM framework, after the commit "f6b8a57 pwm: Add Ingenic
JZ4740 support".
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6525/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 0046be10e0c502705fc74d91408eba13a73bc201 ("mips: delete
non-required instances of include <linux/init.h>") inadvertently
removed an include that was actually correct. Restore it.
Note that it gets init.h implicitly anyway, so this is largely a
cosmetic fixup; no build regressions were caused by this.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6416/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
F7D4302 are reasonable guesses which are unlikely to cause
mis-detection.
Signed-off-by: Cody P Schafer <devel@codyps.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Cc: Cody P Schafer <devel@codyps.com>
Patchwork: https://patchwork.linux-mips.org/patch/6594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds board detection for the Siemens SE505v2 and the led gpio
configuration. This board does not have any buttons.
This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6593/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds led and button GPIO configuration for Linksys wrt54g3gv2,
wrt54gsv1 and wrtsl54gs. This is based on OpenWrt broadcom-diag code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6592/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Linksys WRT54G/GS/GL family uses the same boardtype numbers, and
the same gpio configuration. The boardtype numbers are changing with
the hardware versions, but these hardware numbers are different or each
model.
Detect them all as one device, this also worked in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The M5150 core is a 32-bit MIPS RISC which implements the
MIPS Architecture Release-5 in a 5-stage pipeline.
In addition, it includes the MIPS Architecture Virtualization Module
that enables virtualization of operating systems,
which provides a scalable, trusted, and secure execution environment.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6596/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The previous NR_CPUS=2 default is not an optimal default for current
Malta setups where it is common to have more than 2 CPUs available. It
makes sense to increase this to a number which covers all common setups
currently in use, such that all of those cores are usable. 8 seems to
fit that description.
If the user has less than 8 CPUs & they wish to have a more optimal
kernel they can simply reduce this in their config. It makes sense for
the default to work on as many systems as possible.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6580/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Malta defconfigs which may run on an SMP configuration without
hardware cache anti-aliasing, a 16KB page size is a safer default.
Most notably at the moment it will avoid cache aliasing issues for
multicore proAptiv systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6579/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recent versions of udev and systemd require the kernel
to be compiled with CONFIG_DEVTMPFS in order to populate
the /dev directory. Most MIPS platforms have it enabled by
default, so enable it for Malta configs as well.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6582/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch simply regenerates the malta defconfigs such that they don't
change after being used & saved as a defconfig again. ie. it is the
result of running the following:
for cfg in arch/mips/configs/malta*; do
ARCH=mips make `basename ${cfg}`
ARCH=mips make savedefconfig
mv -v defconfig ${cfg}
done
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6578/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The au1xxx-ide driver isn't any faster than pata_platform since it
spends a lot of time busy waiting for DMA to finish; faster PIO/DMA
modes only work on the db1200 with a certain cpu speed, UDMA is broken,
and finally the old IDE layer is on death row, so time to switch to
the newer ATA layer.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6662/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge the db1200.h and db1300.h headers into their only users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6660/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch merges support for all DB1xxx and PB1xxx
boards into a single image, along with a new single defconfig
for them.
Run-tested on DB1300 and DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6577/
Patchwork: https://patchwork.linux-mips.org/patch/6659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy chips have coherent DMA, but for example the USB or AC97
peripherals on the Au1000/1500/1100 are not.
This patch uses DMA_MAYBE_COHERENT on Alchemy and sets coherentio based
on CPU type.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting DMA_MAYBE_COHERENT gives a platform the opportunity to select
use of cache ops at boot.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6575/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow secondary cores to program their segment control registers
during smp bootstrap code. This enables EVA on Malta SMP
configurations
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Shift System Controller memory mapping to 0x80000000
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use a Malta specific function to free the init section once the
kernel has booted. When operating in EVA mode, the physical memory
is shifted to 0x80000000. Kernel is loaded into 0x80000000 (virtual)
so the offset between physical and virtual addresses is 0.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
PHYS_OFFSET is used to denote the physical start address of the
first bank of RAM. When the Malta board is in EVA mode, the physical
start address of RAM is shifted to 0x80000000 so it's necessary to use
this macro in order to make the code EVA agnostic.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The 'ememsize' variable is used to denote the real RAM which is
present on the Malta board. This is different compared to 'memsize'
which is capped to 256MB. The 'ememsize' is used to get the actual
physical memory when setting up the Malta memory layout. This only
makes sense in case the core operates in the EVA mode, and it's
ignored otherwise.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
