If used 64 bit compiler GCC warns that:
drivers/i2c/busses/i2c-s3c2410.c: In function ‘s3c24xx_get_device_quirks’:
drivers/i2c/busses/i2c-s3c2410.c:168:10: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
This patch fixes this by converting "unsigned int" to "kernel_ulong_t".
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_*() functions to make cleanup paths simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the support of the I2C_SMBUS_I2C_BLOCK_DATA transaction
type for the iSMT SMBus Controller.
Signed-off-by: Robert Valiquette <robert.valiquette@intel.com>
Acked-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
OSIF, Open Source InterFace, is a USB based i2c bus master. The
origional design was based on i2c-tiny-usb, but more modern versions
of the firmware running on the MegaAVR microcontroller use a different
protocol over the USB. This code is based on Barry Carter
<barry.carter@gmail.com> driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The RobotFuzz device is not compatible with i2c-tiny-usb. Remove its
entry from the USB table so that the new correct driver can be used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since 93abe8e4 (clk: add non CONFIG_HAVE_CLK routines) code using clk.h
like this platform driver need not depend on HAVE_CLK. Also, remove a
redundant clk.h include from core driver.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C is now configured from the device tree on all platforms
using this controller. Delete the platform data header and move the
definitions into the driver so it is all contained in one single file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Nomadik I2C controller needs to have the slave set-up time
configured based off the clock used to drive the I2C bus block.
Currently this is done with static assignments assuming that the
block is clocked 48MHz which is pretty likely to be bug-prone.
Calculate the SLSU from the equation given in the datasheet
instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
cppcheck rightfully says:
drivers/i2c/busses/i2c-viperboard.c:169: style: Variable 'bytes_xfer' is assigned a value that is never used.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Simplified the probe and remove functions using devm_* functions
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IRQ handler has to be register first before IRQ
is enabled in xiic_reinit().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Code changes to fix checkpatch warnings listed below.
- WARNING: please, no space before tabs
- WARNING: quoted string split across lines
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_request_region() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_kzalloc() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
smatch rightfully says:
drivers/i2c/busses/i2c-imx.c:610 i2c_imx_probe() info: why not propagate 'irq' from platform_get_irq() instead of (-2)?
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For Exynos4 and Exynos5 SoCs from Samsung the i2c clock is based
on a fixed 66 MHz peripheral clock, and therefore is completely
independent of the cpu frequency.
Thus, registering for a CPU freq notifier is very wasteful.
This patch modifes the code such that, i2c bus registers to
cpu_freq_transition only if CONFIG_CPU_FREQ_S3C24XX is enabled.
This change should save a bunch of cpufreq transitions calls
which does not apply to exynos SoCs.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds polling mode support for i2c-s3c2410 driver.The
SATA PHY controller's CMU and TRSV block's are of I2C register
map in exynos5250.These blocks can be configured using i2c.
But i2c controller instance on which these block's sits lacks an
interrupt line.Also the current i2c-s3c2410 driver is only interrupt
driven, thus a polling mode support is required in the driver for
supporting this controller. This patch adds this support to the driver.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hardware supported by the i2c sh_mobile and rcar drivers is only found
on SUPERH or ARCH_SHMOBILE platforms. Restrict non-COMPILE_TEST
compilation to them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a reset GPIO support is specified, request the GPIO and get the chip
out of reset at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This simplifies error and removal paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a muxed i2c bus gets created the default retry count and
timeout of the muxed bus is zero. Hence it it possible that you
end up with a situation where the parent controller sets a default
retry count and timeout which gets applied and used while the muxed
bus (using the same controller) has a default retry count of zero
and a default timeout of 1s (set in i2c_add_adapter()). This can be
solved by initializing the retry count and timeout of the muxed
bus with the values used by the the parent at creation time.
Signed-off-by: Elie De Brauwer <eliedebrauwer@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c fixes from Wolfram Sang:
"Some easy but needed fixes for i2c drivers since rc1"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: bcm2835: Linking platform nodes to adapter nodes
i2c: omap: raw read and write endian fix
i2c: i2c-bcm-kona: Fix module build
i2c: i2c-diolan-u2c: different usb endpoints for DLN-2-U2C
i2c: bcm-kona: remove duplicated include
i2c: davinci: raw read and write endian fix
In order to find I2C devices in the device tree, the platform nodes
have to be known by the I2C core. This requires setting the
dev.of_node parameter of the adapter.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Correct a typo that prevented the driver from being built as a module.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The previous diolan adapter uses other out/in endpoints than
the current DLN-2-U2C in compatibility mode.
They changed from 0x2/0x84 to 0x3/0x83.
This patch gets the endpoints from the usb interface, instead
of hardcode them in the driver.
This was tested on a current DLN-2-U2C board.
Signed-off-by: Martin Vogt <mvogt1@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C IP block expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
Fix to return a negative error code from the bus speed parse
error handling case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using the i2c-eg20t driver and call i2cdetect or probe on the bus,
the driver will print a lot of error messages if there was no ACK
received.
i2cdetect normally print a table with all the available devices. If there
is no device on the address, the table will be empty.
Currently with the i2c-eg20t driver, the table is not visible because
the error messages destroy the table.
Error message: pch_i2c_getack return -71
This patch prevent the driver to print the messages to syslog.
The pch_i2c_wait_for_check_xfer function is the only one who is
calling pch_i2c_getack, so we can delete the function and add the
read to pch_i2c_wait_for_check_xfer.
If no ACK is received, the Message will be printed as a dbg
message.
Fixed print message to be a one liner so we can grep for the
error message.
Tested on Intel Atom E6xx and Eg20t Chipset.
Signed-off-by: Andreas Werner <wernerandy@gmx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Introduce support for Broadcom Serial Controller (BSC) I2C bus found
in the Kona family of Mobile SoCs. FIFO hardware is utilized but only
standard mode (100kHz), fast mode (400kHz), fast mode plus (1MHz), and
I2C high-speed (3.4 MHz) bus speeds are supported.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
[wsa: fixed Kconfig sorting, squashed broken out patches into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As we claim to support device tree for mach-omap2, we
should have the necessary flags in the driver to make it
usable.
Cc: linux-i2c@vger.kernel.org
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we're missing two lines needed to make it
work properly with device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current I2C adapter id - client address "x-00yy" based device naming scheme
is not always stable enough to be used in name based matching, for instance
within ALSA SoC subsystem.
This is problematic in PC kind of platforms where I2C adapter numbers can
change due variable amount of bus controllers, probe order, add-on cards or
just because of BIOS settings.
This patch addresses the problem by using the ACPI device name with
"i2c-" prefix for ACPI enumerated I2C slaves. For them device name
"x-00yz" becomes "i2c-INTABCD:ij" after this patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
Add the missing clk_disable_unprepare() before return
from wmt_i2c_reset_hardware() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org # 3.11+
Newer Intel PCHs with LPSS have the same Designware I2C controllers than
Haswell but the ACPI IDs differ. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the SMBus Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support to SSC (Synchronous Serial Controller)
I2C driver. This IP also supports SPI protocol, but this is not
the aim of this driver.
This IP is embedded in all ST SoCs for Set-top box platorms, and
supports I2C Standard and Fast modes.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABCAAGBQJSfPKLAAoJEILEb/54YlRxH6YQAJwDKi25RCZziFSIenXuqzC/
c6JxoH/tSnDHJHhcTgqh7H7Raa+zmatMDf0m2oEv2Wjfx4Lt4BQK4iefhe/zY4lX
yJ8uXDg+U8DYhDX2XwbwnFpd1M1k/A+s2gIHDTHHGnE0kDngXdd8RAFFktBmooTZ
l5LBQvOrTlgX/ZfqI/MNmQ6lfY6kbCABGSHV1tUUsDA6Kkvk/LAUTOMSmptv1q22
hcs6k55vR34qADPkUX5GghjmcYJv+gNtvbDEJUjcmCwVoPWouF415m7R5lJ8w3/M
49Q8Tbu5HELWLwca64OorS8qh/P7sgUOf1BX5IDzHnJT+TGeDfvcYbMv2Z275/WZ
/bqhuLuKBpsHQ2wvEeT+lYV3FlifKeTf1FBxER3ApjzI3GfpmVVQ+dpEu8e9hcTh
ZTPGzziGtoIsHQ0unxb+zQOyt1PmIk+cU4IsKazs5U20zsVDMcKzPrb19Od49vMX
gCHvRzNyOTqKWpE83Ss4NGOVPAG02AXiXi/BpuYBHKDy6fTH/liKiCw5xlCDEtmt
lQrEbupKpc/dhCLo5ws6w7MZzjWJs2eSEQcNR4DlR++pxIpYOOeoPTXXrghgZt2X
mmxZI2qsJ7GAvPzII8OBeF3CRO3fabZ6Nez+M+oEZjGe05ZtpB3ccw410HwieqBn
dYpJFt/BHK189odhV9CM
=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
Pankaj Dubey
Jingoo Han
jean-jacques hiblot
robert.valiquette@intel.com
Andrew Lunn
Baruch Siach
Linus Walleij
Wolfram Sang
Kedareswara rao Appana
Michal Simek
Naveen Krishna Ch
Vasanth Ananthan
Laurent Pinchart
Laurent Pinchart
Wolfram Sang
Fabio Estevam
Elie De Brauwer
Linus Torvalds
Florian Meier
Victor Kamensky
Tim Kryger
Martin Vogt
Wei Yongjun
Taras Kondratiuk
Olof Johansson
Andreas Werner
Tony Lindgren
Jarkko Nikula
Rafael J. Wysocki
Mika Westerberg
James Ralston
Sachin Kamat
Maxime COQUELIN
Rob Herring