* 'at91-fixes-for-linus' of git://github.com/at91linux/linux-2.6-at91:
AT91: at91sam9261ek: remove C99 comments but keep information
AT91: at91sam9261ek board: remove warnings related to use of SPI or SD/MMC
AT91: dm9000 initialization update
AT91: SAM9G45 - add a separate clock entry for every single TC block
AT91: clock: peripheral clocks can have other parent than mck
AT91: change dma resource index
The sd/mmc data structure is not used if SPI is selected. The configuration
of PIO on the board prevent from using both interfaces at the same time
(board dependent).
Remove the warnings at compilation time adding a preprocessor condition.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add information in dm9000 mac/phy chip initialization:
- irq resource details
- platform data details
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Partially revert e69edc7, which introduced automatic zreladdr
support. The change in the way the manual definition is defined
seems to be error and conflict prone. Go back to the original way
we were handling this for the time being, while keeping the automatic
zreladdr facility.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without this patch you will not be able to register the first block
because of the second association call on at91_add_device_tc().
Signed-off-by: Fabian Godehardt <fg@emlix.com>
[nicolas.ferre@atmel.com: change tcb1_clk to fake child clock of tcb0_clk]
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
While registering clock allow to set parent clock other
than mck. It is useful for clocks than can be seen as
child clock of a peripheral.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Dave Hylands reports:
| We've observed a problem with dma_alloc_writecombine when the system
| is under heavy load (heavy bus traffic). We've managed to reduce the
| problem to the following snippet, which is run from a kthread in a
| continuous loop:
|
| void *virtAddr;
| dma_addr_t physAddr;
| unsigned int numBytes = 256;
|
| for (;;) {
| virtAddr = dma_alloc_writecombine(NULL,
| numBytes, &physAddr, GFP_KERNEL);
| if (virtAddr == NULL) {
| printk(KERN_ERR "Running out of memory\n");
| break;
| }
|
| /* access DMA memory allocated */
| tmp = virtAddr;
| *tmp = 0x77;
|
| /* free DMA memory */
| dma_free_writecombine(NULL,
| numBytes, virtAddr, physAddr);
|
| ...sleep here...
| }
|
| By itself, the code will run forever with no issues. However, as we
| increase our bus traffic (typically using DMA) then the *tmp = 0x77
| line will eventually cause a page fault. If we add a small delay (a
| few microseconds) before the *tmp = 0x77, then we don't see a page
| fault, even under heavy load.
A dsb() is required after modifying the PTE entries to ensure that they
will always be visible. Add this dsb().
Reported-by: Dave Hylands <dhylands@gmail.com>
Tested-by: Dave Hylands <dhylands@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 7cfe24947 ("ARM: AMBA: Add pclk support to AMBA bus
infrastructure") changed AMBA bus to handle the PCLK automatically.
However, in EP93xx clock initialization is arch_initcall which is done
later than AMBA device identification. This causes
amba_get_enable_pclk() to fail resulting device where UARTs are not
functional.
So change ep93xx_clock_init() to be postcore_initcall.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 4fa5518, which causes a compilation regression for
IXP4xx platforms.
Reported-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The validate_event function in the ARM perf events backend has the
following problems:
1.) Events that are disabled count towards the cost.
2.) Events associated with other PMUs [for example, software events or
breakpoints] do not count towards the cost, but do fail validation,
causing the group to fail.
This patch changes validate_event so that it ignores events in the
PERF_EVENT_STATE_OFF state or that are scheduled for other PMUs.
Reported-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPU_32v6K is selected by CPU_V7 but it only depends on CPU_V6.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fixes the warning:
.config:369:warning: symbol value '' invalid for ZRELADDR
and the prompt for ZRELADDR on make
Signed-off-by: Erik Gilling <konkers@android.com>
The 2.6.36-rc kernel added three new system calls:
fanotify_init, fanotify_mark, and prlimit64. This patch
wires them up on ARM.
The only non-trivial issue here is the u64 argument to
sys_fanotify_mark(), but it is the 3rd argument and thus
passed in r2/r3 in both kernel and user space, so it causes
no problems.
Tested with a 2.6.36-rc2 EABI kernel on an ixp4xx machine.
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is purely a cosmetic change to the ARM perf backend because the current
comments about the relationship between NMIs, interrupt context and
perf_event_do_pending are misleading.
This patch updates the comments so that they reflect what the code
actually does (which is in line with other architectures).
Acked-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes the compiler warning:
arch/arm/plat-pxa/pwm.c: In function 'pwm_probe':
arch/arm/plat-pxa/pwm.c:179: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
According to PXA3xx Processor Family Developer Manuall Vol1. section
"Pin Descriptions and Control", PXA30x and PXA31x Processor Alternate
Function Table shows the Alt FN 0 for GPIO51 is CI_HSYNC and for GPIO52
is CI_VSYNC. This patch fixes the MFP defines and also corrects the
order of MFD defines.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This is causing section mismatches when linking, as cpufreq_driver->init()
is not supposed to be in init section.
Reported-by: Tomáš 'Sleep_Walker' Čech <sleep_walker@suse.cz>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S5PV310: Fix on Secondary CPU startup
ARM: S5PV310: Bug fix on uclk1 and sclk_pwm
ARM: S5PV310: Fix missed uart clocks
ARM: S5PV310: Should be clk_sclk_apll not clk_mout_apll
ARM: S5PV310: Fix on PLL setting for S5PV310
ARM: S5PV310: Add CMU block for S5PV310 Clock
ARM: S5PV310: Fix on typo irqs.h of S5PV310
ARM: S5PV310: Fix on default ZRELADDR of ARCH_S5PV310
ARM: S5PV310: Fix on GPIO base addresses
ARM: SAMSUNG: Fix on build warning regarding VMALLOC_END type
ARM: S5P: VMALLOC_END should be unsigned long
* 'for-linus' of git://android.git.kernel.org/kernel/tegra:
arm: tegra: VMALLOC_END should be unsigned long
arm: tegra: fix compilation of board-harmony.c
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: PM: ensure IO wakeups are properly disabled
omap: Fix omap_4430sdp_defconfig for make oldconfig
omap: Use CONFIG_SMP for test_for_ipi and test_for_ltirq
omap: Fix sev instruction usage for multi-omap
OMAP3: Fix a cpu type check problem
omap3: id: fix 3630 rev detection
Following occurs on boot message without this patch.
CPU1: processor failed to boot
Brought up 1 CPUs
SMP: Total of 1 processors activated...
This patch adds SYSRAM mapping for fixing Secondary CPU startup.
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated...
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes on enable and ctrlbit of uclk1 and sclk_pwm.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds missed uart clocks for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds clk_sclk_apll so that fixes on clk_mout_apll.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes on PLL setting for S5PV310/S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds CMU block for S5PV310/S5PC210 clock.
(CMU: Clock Management Unit)
Of course, changed current clock addresses for it together.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S5PV310/S5PC210 has following three GPIO base addresses.
Part1 Base Address=0x11400000
Part2 Base Address=0x11000000
Part3 Base Address=0x03860000
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor edit of title]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix this warning:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:644: warning: format '%08lx' expects type
'long unsigned int', but argument 12 has type 'unsigned int'
And removes the useless parens and white space.
Reported-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
The build failure was introduced by
13dd0c9 (USB: otg/ulpi: extend the generic ulpi driver.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Silences following build warning:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:644: warning: format '%08lx' expects type 'long
unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Silences following build warning:
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:644: warning: format '%08lx' expects type 'long
unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@google.com>
The patch "ARM: Remove DISCONTIGMEM support" removed the node id from
the meminfo struct and the PHYS_TO_NID macro, causing compilation errors:
arch/arm/mach-tegra/board-harmony.c: In function 'tegra_harmony_fixup':
arch/arm/mach-tegra/board-harmony.c:94: error: 'struct membank' has no member named 'node'
arch/arm/mach-tegra/board-harmony.c:94: error: implicit declaration of function 'PHYS_TO_NID'
arch/arm/mach-tegra/board-harmony.c:97: error: 'struct membank' has no member named 'node'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@google.com>
The core of i.MX5 series is cortex-A8, its cache line size is 64 bytes
instead of 32 bytes. Refer to the OMAP3's selection, we choose 64
bytes for i.MX5, this can increase a little bit performance when
perform cache operations.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We can see MXC_CCM_CCGRx_MOD_OFF is defined as 0 while
MXC_CCM_CCGRx_CG_MASK is defined as 0x3 in crm_regs.h, here in the
_clk_ccgr_disable function, we want to clear the corresponding enable
bit fields to disable this clock, so we should choose MASK instead of
OFF otherwise clocks can't be disabled.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When we call tzic_enable_wake function, the kernel will crash because
of access to an unmapped address. This is because two register
access operations forgot to add base address.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Each board can override the default sdhci host capabilities.
Some board has broken features by hardwares and support 8-bit bandwidth.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SDHI1 on AP4EVB has no pin to detect write protection of a card.
This had the result that a card inserted in this slot was always detected
as read only. This patch adds the corresponding flag to disable
write protection detection for SDHI1.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Noone is using tty argument so let's get rid of it.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
AP4EVB has to reparent PLLC2 to provide a precise HDMI clock, this is only
possible, if PLLC2 hasn't been enabled yet. Since no other driver currently
uses PLLC2 we can safely remove the CLK_ENABLE_ON_INIT flag. This fixes
the "Cannot set PLLC2 parent: -16, 1 users" error message, when trying to
use HDMI on AP4EVB.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Linus Torvalds
Nicolas Ferre
Russell King
Fabian Godehardt
Mika Westerberg
Will Deacon
Catalin Marinas
Erik Gilling
Mikael Pettersson
Uwe Kleine-König
Axel Lin
Eric Miao
Changhwan Youn
Jongpill Lee
Kukjin Kim
Kyungmin Park
Olof Johansson
Jason Wang
Arnd Hannemann
Dmitry Torokhov
Kuninori Morimoto
Guennadi Liakhovetski