We now cache the MSI-X capability offset in the struct pci_dev, so no
need to find the capability again.
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
PCI_MSIX_FLAGS_BIRMASK is mis-named because the BIR mask is in the
Table Offset register, not the flags ("Message Control" per spec)
register.
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
For quite a few Xen versions, this wasn't the IRQ vector anymore
anyway, and it is not being used by the kernel for anything. Hence
drop the field from struct irq_info, and respective function
parameters.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
There is no hypercall to setup multiple MSI per PCI device.
As such with these two new commits:
- 08261d87f7
PCI/MSI: Enable multiple MSIs with pci_enable_msi_block_auto()
- 5ca72c4f7c
AHCI: Support multiple MSIs
we would call the PHYSDEVOP_map_pirq 'nvec' times with the same
contents of the PCI device. Sander discovered that we would get
the same PIRQ value 'nvec' times and return said values to the
caller. That of course meant that the device was configured only
with one MSI and AHCI would fail with:
ahci 0000:00:11.0: version 3.0
xen: registering gsi 19 triggering 0 polarity 1
xen: --> pirq=19 -> irq=19 (gsi=19)
(XEN) [2013-02-27 19:43:07] IOAPIC[0]: Set PCI routing entry (6-19 -> 0x99 -> IRQ 19 Mode:1 Active:1)
ahci 0000:00:11.0: AHCI 0001.0200 32 slots 4 ports 6 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
ahci: probe of 0000:00:11.0 failed with error -22
That is b/c in ahci_host_activate the second call to
devm_request_threaded_irq would return -EINVAL as we passed in
(on the second run) an IRQ that was never initialized.
CC: stable@vger.kernel.org
Reported-and-Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
PV on HVM guests map GSIs into event channels. At restore time the
event channels are resumed by restore_pirqs.
Device drivers might try to register the same GSI again through ACPI at
restore time, but the GSI has already been mapped and bound by
restore_pirqs. This patch detects these situations and avoids
mapping the same GSI multiple times.
Without this patch we get:
(XEN) irq.c:2235: dom4: pirq 23 or emuirq 28 already mapped
and waste a pirq.
CC: stable@kernel.org
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- PV multiconsole support, so that there can be hvc1, hvc2, etc;
- P-state and C-state power management driver that uploads said
power management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPZ0qkAAoJEFjIrFwIi8fJjCgH/jeJ39E8ML8DP9tCS2HQnMqM
uTEjLcqvoJ7sEhHvtBLPeG2p0jyBvOWjLbSc7P8nESBAMPvSYol8L6WqfWrdSU4r
lHrma2sg9UYzRog5NyxAgkp7bBsBBFOnhVL3Cxb5Ig78cPWzeSWGpqGZ8M/d51Wf
1iE0tHuU4DpN+fg1SZqPqEm8ecEJ/eSrVTnyTx/Qo2Ak+Zw98SqzX7SV5lo8mudd
WFL1F2K9FyTNk79ndGhqFt36x6nEbFgMLbmCDWumLuWN6bMd1Uq0wNkCqW4F1h28
3yqnY+rfQh4y3eXK1B9nttCUTs+/66U5ZWrT6B1IJumGTAIqcWfgeUX/Vn/HVC4=
=tfMc
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen updates from Konrad Rzeszutek Wilk:
"which has three neat features:
- PV multiconsole support, so that there can be hvc1, hvc2, etc; This
can be used in HVM and in PV mode.
- P-state and C-state power management driver that uploads said power
management data to the hypervisor. It also inhibits cpufreq
scaling drivers to load so that only the hypervisor can make power
management decisions - fixing a weird perf bug.
There is one thing in the Kconfig that you won't like: "default y
if (X86_ACPI_CPUFREQ = y || X86_POWERNOW_K8 = y)" (note, that it
all depends on CONFIG_XEN which depends on CONFIG_PARAVIRT which by
default is off). I've a fix to convert that boolean expression
into "default m" which I am going to post after the cpufreq git
pull - as the two patches to make this work depend on a fix in Dave
Jones's tree.
- Function Level Reset (FLR) support in the Xen PCI backend.
Fixes:
- Kconfig dependencies for Xen PV keyboard and video
- Compile warnings and constify fixes
- Change over to use percpu_xxx instead of this_cpu_xxx"
Fix up trivial conflicts in drivers/tty/hvc/hvc_xen.c due to changes to
a removed commit.
* tag 'stable/for-linus-3.4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen kconfig: relax INPUT_XEN_KBDDEV_FRONTEND deps
xen/acpi-processor: C and P-state driver that uploads said data to hypervisor.
xen: constify all instances of "struct attribute_group"
xen/xenbus: ignore console/0
hvc_xen: introduce HVC_XEN_FRONTEND
hvc_xen: implement multiconsole support
hvc_xen: support PV on HVM consoles
xenbus: don't free other end details too early
xen/enlighten: Expose MWAIT and MWAIT_LEAF if hypervisor OKs it.
xen/setup/pm/acpi: Remove the call to boot_option_idle_override.
xenbus: address compiler warnings
xen: use this_cpu_xxx replace percpu_xxx funcs
xen/pciback: Support pci_reset_function, aka FLR or D3 support.
pci: Introduce __pci_reset_function_locked to be used when holding device_lock.
xen: Utilize the restore_msi_irqs hook.
to make a hypercall to restore the vectors in the MSI/MSI-X
configuration space.
Signed-off-by: Tang Liang <liang.tang@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* 'stable/drivers-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: don't rely on xen_initial_domain to detect local xenstore
xenbus: Fix loopback event channel assuming domain 0
xen/pv-on-hvm:kexec: Fix implicit declaration of function 'xen_hvm_domain'
xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel
xen/pv-on-hvm kexec: update xs_wire.h:xsd_sockmsg_type from xen-unstable
xen/pv-on-hvm kexec+kdump: reset PV devices in kexec or crash kernel
xen/pv-on-hvm kexec: rebind virqs to existing eventchannel ports
xen/pv-on-hvm kexec: prevent crash in xenwatch_thread() when stale watch events arrive
* 'stable/drivers.bugfixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Check if the device is found instead of blindly assuming so.
xen/pciback: Do not dereference psdev during printk when it is NULL.
xen: remove XEN_PLATFORM_PCI config option
xen: XEN_PVHVM depends on PCI
xen/pciback: double lock typo
xen/pciback: use mutex rather than spinlock in vpci backend
xen/pciback: Use mutexes when working with Xenbus state transitions.
xen/pciback: miscellaneous adjustments
xen/pciback: use mutex rather than spinlock in passthrough backend
xen/pciback: use resource_size()
* 'stable/pci.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: support multi-segment systems
xen-swiotlb: When doing coherent alloc/dealloc check before swizzling the MFNs.
xen/pci: make bus notifier handler return sane values
xen-swiotlb: fix printk and panic args
xen-swiotlb: Fix wrong panic.
xen-swiotlb: Retry up three times to allocate Xen-SWIOTLB
xen-pcifront: Update warning comment to use 'e820_host' option.
There are three different modes: PV, HVM, and initial domain 0. In all
the cases we would return -1 for failure instead of a proper error code.
Fix this by propagating the error code from the generic IRQ code.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Now that the hypercall interface changes are in -unstable, make the
kernel side code not ignore the segment (aka domain) number anymore
(which results in pretty odd behavior on such systems). Rather, if
only the old interfaces are available, don't call them for devices on
non-zero segments at all.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
[v1: Edited git description]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past we would only use the function's value if the
returned value was not equal to 'acpi_sci_override_gsi'. Meaning
that the INT_SRV_OVR values for global and source irq were different.
But it is OK to use the function's value even when the global
and source irq are the same.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past (2.6.38) the 'xen_allocate_pirq_gsi' would allocate
an entry in a Linux IRQ -> {XEN_IRQ, type, event, ..} array. All
of that has been removed in 2.6.39 and the Xen IRQ subsystem uses
an linked list that is populated when the call to
'xen_allocate_irq_gsi' (universally done from any of the xen_bind_*
calls) is done. The 'xen_allocate_pirq_gsi' is a NOP and there is
no need for it anymore so lets remove it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
As the code paths that are guarded by CONFIG_XEN_DOM0 already depend
on CONFIG_ACPI so the extra #ifdef is not required. The earlier
patch that added them in had done its job.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
.. which means we can preset of NR_IRQS_LEGACY interrupts using
the 'acpi_get_override_irq' API before this loop.
This means that we can get the IRQ's polarity (and trigger) from either
the ACPI (or MP); or use the default values. This fixes a bug if we did
not have an IOAPIC we would not been able to preset the IRQ's polarity
if the MP table existed.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since they are only called once and the rest of the pci_xen_*
functions follow the same pattern of setup.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past we would guard those code segments to be dependent
on CONFIG_XEN_DOM0 (which depends on CONFIG_ACPI) so this patch is
not stricly necessary. But the next patch will merge common
HVM and initial domain code and we want to make sure the CONFIG_ACPI
dependency is preserved - as HVM code does not depend on CONFIG_XEN_DOM0.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Update the out-dated comment at the beginning of the file.
Also provide the copyrights of folks who have been contributing
to this code lately.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The file is hard to read. Move the code around so that
the contents of it follows a uniform format:
- setup GSIs - PV, HVM, and initial domain case
- then MSI/MSI-x setup - PV, HVM and then initial domain case.
- then MSI/MSI-x teardown - same order.
- lastly, the __init functions in PV, HVM, and initial domain order.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Previously we would check for acpi_sci_override_gsi == gsi every time
a PCI device was enabled. That works during early bootup, but later
on it could lead to triggering unnecessarily the acpi_gsi_to_irq(..) lookup.
The reason is that acpi_sci_override_gsi was declared in __initdata and
after early bootup could contain bogus values.
This patch moves the check for acpi_sci_override_gsi to the
site where the ACPI SCI is preset.
CC: stable@kernel.org
Reported-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
Tested-by: Raghavendra D Prabhu <rprabhu@wnohang.net>
[http://lists.xensource.com/archives/html/xen-devel/2011-07/msg00154.html]
Suggested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In the past we would use the GSI value to preset the ACPI SCI
IRQ which worked great as GSI == IRQ:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
While that is most often seen, there are some oddities:
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
which means that GSI 20 (or pin 20) is to be overriden for IRQ 9.
Our code that presets the interrupt for ACPI SCI however would
use the GSI 20 instead of IRQ 9 ending up with:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=20
xen: acpi sci 20
.. snip..
calling acpi_init+0x0/0xbc @ 1
ACPI: SCI (IRQ9) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20110413/evevent-119)
ACPI: Unable to start the ACPI Interpreter
as the ACPI interpreter made a call to 'acpi_gsi_to_irq' which got nine.
It used that value to request an IRQ (request_irq) and since that was not
present it failed.
The fix is to recognize that for interrupts that are overriden (in our
case we only care about the ACPI SCI) we should use the IRQ number
to present the IRQ instead of the using GSI. End result is that we get:
xen: sci override: global_irq=20 trigger=0 polarity=1
xen: registering gsi 20 triggering 0 polarity 1
xen: --> pirq=20 -> irq=9 (gsi=9)
xen: acpi sci 9
which fixes the ACPI interpreter failing on startup.
CC: stable@kernel.org
Reported-by: Liwei <xieliwei@gmail.com>
Tested-by: Liwei <xieliwei@gmail.com>
[http://lists.xensource.com/archives/html/xen-devel/2011-06/msg01727.html]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If we have CONFIG_XEN and the other parameters to build an
Linux kernel that is non-privileged, the xen_[find|register|unregister]_
device_domain_owner functions should not be compiled. They should
use the nops defined in arch/x86/include/asm/xen/pci.h instead.
This fixes:
arch/x86/pci/xen.c:496: error: redefinition of ‘xen_find_device_domain_owner’
arch/x86/include/asm/xen/pci.h:25: note: previous definition of ‘xen_find_device_domain_owner’ was here
arch/x86/pci/xen.c:510: error: redefinition of ‘xen_register_device_domain_owner’
arch/x86/include/asm/xen/pci.h:29: note: previous definition of ‘xen_register_device_domain_owner’ was here
arch/x86/pci/xen.c:532: error: redefinition of ‘xen_unregister_device_domain_owner’
arch/x86/include/asm/xen/pci.h:34: note: previous definition of ‘xen_unregister_device_domain_owner’ was here
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
We check if there is a domain owner for the PCI device. In case of failure
(meaning no domain has registered for this device) we make DOMID_SELF the owner.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: deal with rebasing on v2.6.37-1]
[v3: deal with rebasing on stable/irq.cleanup]
[v4: deal with rebasing on stable/irq.ween_of_nr_irqs]
[v5: deal with rebasing on v2.6.39-rc3]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Xiantao Zhang <xiantao.zhang@intel.com>
When the Xen PCI backend is told to enable or disable MSI/MSI-X functions,
the initial domain performs these operations. The initial domain needs
to know which domain (guest) is going to use the PCI device so when it
makes the appropiate hypercall to retrieve the MSI/MSI-X vector it will
also assign the PCI device to the appropiate domain (guest).
This boils down to us needing a mechanism to find, set and unset the domain
id that will be using the device.
[v2: EXPORT_SYMBOL -> EXPORT_SYMBOL_GPL.]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Following the example set by xen_allocate_pirq_msi and
xen_bind_pirq_msi_to_irq:
xen_allocate_pirq becomes xen_allocate_pirq_gsi and now only allocates
a pirq number and does not bind it.
xen_map_pirq_gsi becomes xen_bind_pirq_gsi_to_irq and binds an
existing pirq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The function name does not distinguish it from xen_allocate_pirq_msi
(which operates on domU and pvhvm domains rather than dom0).
Hoist domain 0 specific functionality up into the only caller leaving
functionality common to all guest types in xen_bind_pirq_msi_to_irq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Makes the tail end of this function look even more like
xen_bind_pirq_msi_to_irq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Split the binding aspect of xen_allocate_pirq_msi out into a new
xen_bind_pirq_to_irq function.
In xen_hvm_setup_msi_irq when allocating a pirq write the MSI message
to signal the PIRQ as soon as the pirq is obtained. There is no way to
free the pirq back so if the subsequent binding to an IRQ fails we
want to ensure that we will reuse the PIRQ next time rather than leak
it.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
apic_register_gsi_xen_hvm is a tiny wrapper around
xen_hvm_register_pirq.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
consistent with other similar functions.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
All callers pass this flag so it is pointless.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fixes:
CC arch/x86/pci/xen.o
arch/x86/pci/xen.c:183: warning: 'xen_initdom_setup_msi_irqs' defined but not used
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* stable/pcifront-fixes:
pci/xen: When free-ing MSI-X/MSI irq->desc also use generic code.
pci/xen: Cleanup: convert int** to int[]
pci/xen: Use xen_allocate_pirq_msi instead of xen_allocate_pirq
xen-pcifront: Sanity check the MSI/MSI-X values
xen-pcifront: don't use flush_scheduled_work()
This happens to not be an issue currently because we take pains to try
to ensure that the GSI-IRQ mapping is 1-1 in a PV guest and that
regular event channels do not clash. However a subsequent patch is
going to break this 1-1 mapping.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
This code path is only run when an MSI/MSI-X PCI device is passed
in to PV DomU.
In 2.6.37 time-frame we over-wrote the default cleanup handler for
MSI/MSI-X irq->desc to be "xen_teardown_msi_irqs". That function
calls the the xen-pcifront driver which can tell the backend to
cleanup/take back the MSI/MSI-X device.
However, we forgot to continue the process of free-ing the MSI/MSI-X
device resources (irq->desc) in the PV domU side. Which is what
the default cleanup handler: default_teardown_msi_irqs did.
Hence we would leak IRQ descriptors.
Without this patch, doing "rmmod igbvf;modprobe igbvf" multiple
times ends with abandoned IRQ descriptors:
28: 5 xen-pirq-pcifront-msi-x
29: 8 xen-pirq-pcifront-msi-x
...
130: 10 xen-pirq-pcifront-msi-x
with the end result of running out of IRQ descriptors.
Reviewed-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cleanup code. Cosmetic change to make the code look easier
to read.
Reviewed-by: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
xen_allocate_pirq -> xen_map_pirq_gsi -> PHYSDEVOP_alloc_irq_vector IFF
xen_initial_domain() in addition to the kernel side book-keeping side of
things (set chip and handler, update irq_info etc) whereas
xen_allocate_pirq_msi just does the kernel book keeping.
Also xen_allocate_pirq allocates an IRQ in the 1-1 GSI space whereas
xen_allocate_pirq_msi allocates a dynamic one in the >GSI IRQ space.
All of this is uneccessary as this code path is only executed
when we run as a domU PV guest with an MSI/MSI-X PCI card passed in.
Hence we can jump straight to allocating an dynamic IRQ (and
binding it to the proper PIRQ) and skip the rest.
In short: this change is a cosmetic one.
Reviewed-by: Ian Campbell <Ian.Campbell@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When remapping MSIs into pirqs for PV on HVM guests, qemu is responsible
for doing the actual mapping and unmapping.
We only give qemu the desired pirq number when we ask to do the mapping
the first time, after that we should be reading back the pirq number
from qemu every time we want to re-enable the MSI.
This fixes a bug in xen_hvm_setup_msi_irqs that manifests itself when
trying to enable the same MSI for the second time: the old MSI to pirq
mapping is still valid at this point but xen_hvm_setup_msi_irqs would
try to assign a new pirq anyway.
A simple way to reproduce this bug is to assign an MSI capable network
card to a PV on HVM guest, if the user brings down the corresponding
ethernet interface and up again, Linux would fail to enable MSIs on the
device.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Stanse found that xen_setup_msi_irqs leaks memory when
xen_allocate_pirq fails. Free the memory in that fail path.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: xen-devel@lists.xensource.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Implement xen_create_msi_irq to create an msi and remap it as pirq.
Use xen_create_msi_irq to implement an initial domain specific version
of setup_msi_irqs.
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Yunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Implement xen_register_gsi to setup the correct triggering and polarity
properties of a gsi.
Implement xen_register_pirq to register a particular gsi as pirq and
receive interrupts as events.
Call xen_setup_pirqs to register all the legacy ISA irqs as pirqs.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Map MSIs into pirqs, writing 0 in the MSI vector data field and the pirq
number in the MSI destination id field.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Disable pcifront when running on HVM: it is meant to be used with pv
guests that don't have PCI bus.
Use acpi_register_gsi_xen_hvm to remap GSIs into pirqs.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
xen_hvm_register_pirq allows the kernel to map a GSI into a Xen pirq and
receive the interrupt as an event channel from that point on.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This looks to be vestigial dependency that had never been used even
in the original code base (2.6.18) from which this driver
was up-ported. Without this fix, with the CONFIG_ISAPNP, we get this
compile failure:
arch/x86/pci/xen.c: In function 'pci_xen_init':
arch/x86/pci/xen.c:138: error: 'isapnp_disable' undeclared (first use in this function)
arch/x86/pci/xen.c:138: error: (Each undeclared identifier is reported only once
arch/x86/pci/xen.c:138: error: for each function it appears in.)
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
Tested-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
