Correct the the config register for LDO1.
Fixes: 90e7d52627 (regulator: tps65218: Add Regulator driver for
TPS65218 PMIC)
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15
When setting up .enable_reg for an SMPS regulator, presumably we should
call PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE, ...) rather than using
LDO_BASE. This change makes the LCD panel and HDMI work again on the
NVIDIA Dalmore board anyway.
Fixes: 318dbb02b5 ("regulator: palmas: Fix SMPS enable/disable/is_enabled")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The vbus regulator was not getting its name set. This results
in the sysfs entry being empty. The lack of a bcm590xx_regs[]
table entry also upsets Coverity runs. Add the table entry
so the name gets set properly.
Signed-off-by: Graham Williams <graham.williams@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.
Currently we do not populate these for SMPS other than SMPS10, this
results in spurious results as regmap assumes that the values are
valid and ends up reading register 0x0 RTC:SECONDS_REG on Palmas
variants that do have RTC! To fix this, we update proper parameters
for the descriptor fields.
Further, we want to ensure the behavior consistent with logic
prior to commit dbabd624d4, where, once you do a set_mode,
enable/disable ensure the logic remains consistent and configures
Palmas to the configuration that we set with set_mode (since the
configuration register is common). To do this, we can rely on the
regulator core's regulator_register behavior where the regulator
descriptor pointer provided by the regulator driver is stored. (no
reallocation and copy is done). This lets us update the enable_value
post registration, to remain consistent with the mode we configure as
part of set_mode.
Fixes: dbabd624d4 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
of_find_node_by_name() walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
re-add the perm check (we unified the module param and sysfs checks, but
the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args().
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IxSN
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Most of this is cleaning up various driver sysfs permissions so we can
re-add the perm check (we unified the module param and sysfs checks,
but the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args()"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: set nx before marking module MODULE_STATE_COMING.
samples/kobject/: avoid world-writable sysfs files.
drivers/hid/hid-picolcd_fb: avoid world-writable sysfs files.
drivers/staging/speakup/: avoid world-writable sysfs files.
drivers/regulator/virtual: avoid world-writable sysfs files.
drivers/scsi/pm8001/pm8001_ctl.c: avoid world-writable sysfs files.
drivers/hid/hid-lg4ff.c: avoid world-writable sysfs files.
drivers/video/fbdev/sm501fb.c: avoid world-writable sysfs files.
drivers/mtd/devices/docg3.c: avoid world-writable sysfs files.
speakup: fix incorrect perms on speakup_acntsa.c
cpumask.h: silence warning with -Wsign-compare
Documentation: Update kernel-parameters.tx
param: hand arguments after -- straight to init
modpost: Fix resource leak in read_dump()
get_voltage_sel reads from SMPS register - if the read selector value
is 0, the SMPS is actually disabled - So, this is in addition to the
ctrl_register that may also be used to enable/disable the SMPS.
The original logic(prior to commit dbabd624d4) used to be:
static int palmas_map_voltage_smps(struct regulator_dev *rdev,
int min_uV, int max_uV)
<snip>
if (min_uV == 0)
return 0;
To handle this scenario, with the transition to regulator_list
implementation, we seem to have missed the data necessary to mark as
one of the valid entries as "0" 'disabled regulator' which results in
0 volts - So, stick with pre-existing logic.
Without this added to the list, palmas regulator driver,
on probe, attempts to setup constraints and in the case of
OMAP5uEVM, SMPS9 (which is mapped for 2v1 audio supply) fails in
regulator_list_voltage_linear_range mapping of '0', and as a fall back
of constraints not being applied, the entire regulator list is not
enumerated due to assumption that something system wide has gone bad
on with the PMIC.
Fixes: dbabd624d4 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- Move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- Fixes reference counting of the DT nodes for constraints from Charles
Keepax. This has little practical impact since all real users of
the regulator bindings use FDT which doesn't need the reference
counting.
- Lots of cleanups, especially to the Samsung drivers.
- Support for Linear Technologies LTC3589, Texas Instruments TPS658640
and X-Powers AXP20x.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JrfM
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into next
Pull regulator updates from Mark Brown:
"The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- fixes to reference counting of the DT nodes for constraints from
Charles Keepax. This has little practical impact since all real
users of the regulator bindings use FDT which doesn't need the
reference counting.
- lots of cleanups, especially to the Samsung drivers.
- support for Linear Technologies LTC3589, Texas Instruments
TPS658640 and X-Powers AXP20x"
* tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (64 commits)
regulator: pbias: remove unnecessary OOM messages
regulator: max8649: remove unnecessary OOM messages
regulator: core: Fix the init of DT defined fixed regulators
regulator: core: Disable unused regulators after deferred probing is done
regulator: Don't disable unused regulators we don't have permission for
regulator: axp20x: Use regulator_map_voltage_ascend for LDO4
regulator: use of_property_read_{bool|u32}()
regulator: Fix regulator_get_{optional,exclusive}() documentation
regulators: Add definition of regulator_set_voltage_time() for !CONFIG_REGULATOR
regulator: arizona-ldo1: add missing #include
regulator: pfuze100: Support enable/disable for fixed regulator
regulator: ltc3589: Remove ltc3589_list_voltage_fixed function
regulator: ltc3589: Fix module dependency
regulator: tps6586x: Remove unused to_tps6586x_dev() function
regulator: tps65218: Convert to use regulator_set_voltage_time_sel
regulator: tps6586x: Add support for the TPS658640
regulator: tps6586x: Prepare supporting fixed regulators
regulator: pfuze100: Don't allocate an invalid gpio
regulator: pfuze100: Support SWB enable/disable
regulator: fixed: use of_property_read_{bool|u32}()
...
As of commit 064d5cd110 (regulator: core: Fix the init of DT defined
fixed regulators) the regulator core tries to query the current voltage
of a regulator when applying constraints. This exposes a bug in the
AS3722 regulator driver which fails to read the voltage of disabled
regulators. The reason is that the hardware is programmed to a selector
of 0, but none of the voltage tables include 0 as a valid selector. The
datasheets indicate that 0 is a valid selector when the regulators are
powered off.
To fix this, add a range including selector 0 to the voltage tables.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here is the big char / misc driver updates for 3.16-rc1.
Lots of different driver updates for a variety of different drivers and
minor driver subsystems.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONWI8ACgkQMUfUDdst+ykvQACdGxTChdEU7edElDAXeelVmu8v
D1UAoLDvqwUsN7t5v+WG2wkOvhf5MEA7
=tVMP
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into next
Pull char/misc driver patches from Greg KH:
"Here is the big char / misc driver update for 3.16-rc1.
Lots of different driver updates for a variety of different drivers
and minor driver subsystems.
All have been in linux-next with no reported issues"
* tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (79 commits)
hv: use correct order when freeing monitor_pages
spmi: of: fixup generic SPMI devicetree binding example
applicom: dereferencing NULL on error path
misc: genwqe: fix uninitialized return value in genwqe_free_sync_sgl()
miscdevice.h: Simple syntax fix to make pointers consistent.
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
mcb: Add support for shared PCI IRQs
drivers: Remove duplicate conditionally included subdirs
misc: atmel_pwm: only build for supported platforms
mei: me: move probe quirk to cfg structure
mei: add per device configuration
mei: me: read H_CSR after asserting reset
mei: me: drop harmful wait optimization
mei: me: fix hw ready reset flow
mei: fix memory leak of mei_clients array
uio: fix vma io range check in mmap
drivers: uio_dmem_genirq: Fix memory leak in uio_dmem_genirq_probe()
w1: do not unlock unheld list_mutex in __w1_remove_master_device()
w1: optional bundling of netlink kernel replies
connector: allow multiple messages to be sent in one packet
...
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a regulator is defined using DT and it has a single voltage the
regulator init always tries to apply this voltage. However it fails if
the regulator isn't settable because it is using an internal low level
function. To overcome this we now first query the regulator and only
set it if needed.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_init_complete does a scan of regulators which dont have
always-on or consumers are automatically disabled as being unused.
However, with deferred probing, late_initcall() is too soon to
declare a regulator as unused as the regulator itself might not
have registered due to defferal - Example: A regulator deffered due
to i2bus not available which in turn is deffered due to pinctrl
availability.
Since deferred probing is done in late_initcall(), do the cleanup of
unused regulators by regulator_init_complete in late_initcall_sync
instead of late_initcall.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
[nm@ti.com: minor rewording]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the spirit of conservatism that governs our general approach to
permissions it is better if we don't touch regulators we weren't explicitly
given permissions to control. This avoids the need to explicitly specify
unknown regulators in DT as always on, if a regulator is not otherwise
involved in software control it can be omitted from the DT.
Regulators explicitly given constraints in DT still need to have an always
on constraint specified as before.
Signed-off-by: Mark Brown <broonie@linaro.org>
The voltages in axp20x_ldo4_data table are in ascendant order, so use
regulator_map_voltage_ascend.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use more compact of_property_read_{bool|u32}() calls instead of the
of_{find|get}_property() calls in of_get_regulation_constraints() where
possible (note that of_property_read_{bool|u32}() were already used to read
some properties).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_get_optional() doesn't hold an exclusive reference to
the regulator. Fix the documentation and reword the exclusive
documentation to fix the grammatical error "this reference is
held".
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
commit 2cce4be9e6 "regulator: arizona-ldo1: Add processing of init_data
from device tree" added a call to of_get_child_by_name() but
did not add an #include to the header file declaring that function.
I got a build error when doing randconfig testing on this, which
is fixed by this patch to include of.h.
drivers/regulator/arizona-ldo1.c:192:2: error: implicit declaration of function 'of_get_child_by_name' [-Werror=implicit-function-declaration]
drivers/regulator/arizona-ldo1.c:193:2: error: implicit declaration of function 'of_parse_phandle' [-Werror=implicit-function-declaration]
drivers/regulator/arizona-ldo1.c:213:2: error: implicit declaration of function 'of_node_put' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code has .enable_reg and .enable_mask settings, but the implementation
for corresponding callbacks are missing. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Robin Gong <b38343@freescale.com>
Acked-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When fixed_uV is set and n_voltage is 1, regulator core will return
rdev->desc->fixed_uV in regulator_get_voltage() and regulator_list_voltage().
Rename ltc3589_standby_regulator_ops to ltc3589_fixed_standby_regulator_ops,
this makes the code clear that the ops is for fixed voltage regulator.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make this driver depend on I2C and select REGMAP_I2C to fix build failure.
Also allows this driver to be built as module.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use regulator_set_voltage_time_sel() instead of open-coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TPS658640 has a different set of output voltage for most LDO and
the RTC LDO isn't settable. This chip also report 2 different version
ID, as the datasheet doesn't list the possible values the second ID
has simply been named TPS658640v2.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the required definitions and macros to allow easily adding fixed
regulators. This required for the TPS658640 that doesn't allow setting
the LDO_RTC output voltage.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously, the PFUZE100 would try to allocate gpio0 io0 because
config.ena_gpio defaults to 0, which can be a valid GPIO. To prevent this
from happening, set this parameter to -EINVAL.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SWB regulators have the ability to be turned on and off. Add
enable/disable support for these regulators.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use more compact of_property_read_{bool|u32}() calls instead of the
of_{find|get}_property() calls.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Linear Technology LTC3589, LTC3589-1,
and LTC3589-2 8-output I2C voltage regulator ICs.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the register for ramp delay of buck1 regulator. Buck1 and buck6
share the field (offset 4) in ramp delay register S2MPA01_REG_RAMP2.
The driver used the same register and field for ramp delay of buck3 and
buck1. This lead to updating of ramp delay of buck3 when setting buck1
and actually the ramp delay of buck1 was never set.
Fixes: f187927146 ("regulator: Add support for S2MPA01 regulator")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org>
Use map_voltage_linear_range() if list_voltage_linear_range() is in use and
nothing is set.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bcm590xx MFD driver now exposes a secondary regmap descriptor
making the registers for regulators on the secondary I2C slave address
available. Add support for GPLDO1-6 and VBUS regulators found within
this register range.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patchset add resource-managed functions to automatically control the memory
and unregistration operation of extcon. Also, This series support new MAX77836
extcon device driver on existing MAX14577 device because existed a little
difference between MAX77836 and MAX14577. Finally, Fix minor issue of extcon
driver.
Detailed description for patchset:
1. Add resource-managed functions
- Add resource-managed functions to automatically free the memory of extcon
structure and to control unregistration behavior as following. This new devm_*
functions applied all of extcon drivers in drivers/extcon/.
: devm_extcon_dev_register/unregister()
: devm_extcon_dev_allocate/free()
: extcon_dev_allocate/free() for devm_extcon_dev_allocate/free()
2. Add new MAX77836 extcon device
- Support MAX77836 device on existing MAX14577 device driver using
different compatible string. This patchset has dependency on MFD/
Regulator/Extcon. So, Lee Jones(MFD Maintainer) created Immutable
branch between MFD and Extcon due for v3.16 merge-window and then
I merged this patchset from MFD git repo[1] to Extcon git repo.
: [1] git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
(branch: ib-mfd-extcon-3.16)
3. Fix minor issue of extcon driver
- extcon-palmas driver
: Fix issue of extcon device name for probe
- extcon-max14577
: Fix probe failure about handling wrong return value.
: Properly Handle return value of regmap_irq_get_virq function.
- extcon-max8997/max77693 driver
: Fix NULL pointer exception on missing pdata
4. Code clean for extcon driver
- extcon-max8997/max77693
: Use power efficient workqueue for delayed cable detection
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7wRd
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for v3.16
This patchset add resource-managed functions to automatically control the memory
and unregistration operation of extcon. Also, This series support new MAX77836
extcon device driver on existing MAX14577 device because existed a little
difference between MAX77836 and MAX14577. Finally, Fix minor issue of extcon
driver.
Detailed description for patchset:
1. Add resource-managed functions
- Add resource-managed functions to automatically free the memory of extcon
structure and to control unregistration behavior as following. This new devm_*
functions applied all of extcon drivers in drivers/extcon/.
: devm_extcon_dev_register/unregister()
: devm_extcon_dev_allocate/free()
: extcon_dev_allocate/free() for devm_extcon_dev_allocate/free()
2. Add new MAX77836 extcon device
- Support MAX77836 device on existing MAX14577 device driver using
different compatible string. This patchset has dependency on MFD/
Regulator/Extcon. So, Lee Jones(MFD Maintainer) created Immutable
branch between MFD and Extcon due for v3.16 merge-window and then
I merged this patchset from MFD git repo[1] to Extcon git repo.
: [1] git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
(branch: ib-mfd-extcon-3.16)
3. Fix minor issue of extcon driver
- extcon-palmas driver
: Fix issue of extcon device name for probe
- extcon-max14577
: Fix probe failure about handling wrong return value.
: Properly Handle return value of regmap_irq_get_virq function.
- extcon-max8997/max77693 driver
: Fix NULL pointer exception on missing pdata
4. Code clean for extcon driver
- extcon-max8997/max77693
: Use power efficient workqueue for delayed cable detection
The of_find_node_by_name function will search for a DT node named
"regulators" after the provided np node, but will not ensure that this node
is a child of np.
This might result in retrieving a "regulators" node that is not related to
the axp20x PMIC.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use regulator API rdev_get_id() to access id of regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
S2MPS11 supports enabling/disabling ramp delay only for buck[2346].
Other bucks have ramp delay enabled always.
However the bit shift for enabling buck6 ramp delay in register is equal
to 0. When ramp delay was set for the bucks unsupporting enable/disable
(buck[15789] and buck10), the ramp delay for buck6 was also enabled.
Fixes: b96244fad9 ("regulator: s2mps11: Don't check enable_shift before setting enable ramp rate")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
