- move some code out of the kmap_atomic() / kunmap_atomic() zone
- remove the redundant "do_write = (qc->tf.flags & ATA_TFLAG_WRITE);"
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
This redoes the n_ports logic I proposed before as a bitmask.
ata_pci_init_native_mode is now used with a mask allowing for mixed mode
stuff later on. ata_pci_init_legacy_port is called with port number and
does one port now not two. Instead it is called twice by the ata init
logic which cleans both of them up.
There are stil limits in the original code left over
- IRQ/port mapping for legacy mode should be arch specific values
- You can have one legacy mode IDE adapter per PCI root bridge on some systems
- Doesn't handle mixed mode devices yet (but is now a lot closer to it)
Replace SCSI's legacy "bang at the door" method of probing with one
directly controlled by the underlying ATA transport layer.
We now only call scsi_scan_target() for devices we find, rather than
probing every possible channel/id within a certain range.
ata_qc_issue_prot():
- cleanup and let the PIO data out case always go through the
ata_dataout_task() codepath.
(Previously for PIO data out case, 2 code pathes were used
- irq case goes through ata_data_out_task() codepath.
- polling case jumps over the HSM_ST_FIRST state and goes to
HSM_ST and ata_pio_task() directly.)
ata_dataout_task():
- rearrange the queue_work() code to handle the PIO data out +
polling case.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Use if (qc->tf.protocol == ATA_PROT_PIO) instead of
if(is_atapi_taskfile()) in ata_dataout_task()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
libata.h:
libata-core:
Add ATA_FLAG_PIO_POLLING flag for LLDs that expect interrupt for
command completion only.
sata_nv.c:
sata_vsc.c:
irq handler is wrapper around ata_host_intr(), can handle PIO interrupts.
sata_promise.c:
sata_sx4.c:
sata_qstor.c:
sata_mv.c:
Private irq handler.
Polling mode ATA_FLAG_PIO_POLLING used for compatibility.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add PIO_ST_FIRST for the state before sending ATAPI CDB or sending
"ATA PIO data out" first data block.
- add ATA_TFLAG_POLLING and ATA_DFLAG_CDB_INTR flags
- remove the ATA_FLAG_NOINTR flag since the interrupt handler is now
aware of the states
- modify ata_pio_sector() and atapi_pio_bytes() to work in the interrupt
context
- modify the ata_host_intr() to handle PIO interrupts
- modify ata_qc_issue_prot() to initialize states
- atapi_packet_task() changed to handle "ATA PIO data out" first data block
- support the pre-ATA4 ATAPI device which raise interrupt when ready to
receive CDB
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Changes:
s/PIO_ST_/HSM_ST_/ and s/pio_task_state/hsm_task_state/.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make sure we that completion is the final action we take; prior to this
change, another CPU may have changed ap->pio_task_state before we tested
it a final time.
Spotted by, and original patch by Albert Lee @ IBM.
Also includes a minor optimization: eliminate a ton of unnecessary
queue_work() calls, simply by jumping to the beginning of the FSM
function ata_pio_task().
ATAPI is getting close to being ready. To increase exposure, we enable
the code in the upstream kernel, but default it to off (present
behavior). Users must pass atapi_enabled=1 as a module option (if
module) or on the kernel command line (if built in) to turn on
discovery of their ATAPI devices.
- changes license of all code from OSL+GPL to plain ole GPL
- except for NVIDIA, who hasn't yet responded about sata_nv
- copyright holders were already contacted privately
- adds info in each driver about where hardware/protocol docs may be
obtained
- where I have made major contributions, updated copyright dates
You spelt heuristic wrongly. Also reformatted to 80 columns,
ignore the diff and fix the typo if you prefer that.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH libata-dev-2.6:upstream] implement ata_poll_qc_complete and use it in polling functions
Previously, libata polling functions turned irq back on and completed
qc commands without holding host lock. This creates a race condition
between the polling task and interrupts from other ports on the same
host set or spurious interrupt from itself.
This patch implements ata_poll_qc_complete which enables irq and
completes qc atomically and convert all polling functions.
Note: atapi_packet_task() didn't use to turn irq back on or clear
ATA_FLAG_NOINTR on error exits. This patch makes it use
ata_poll_qc_complete which does both.
Note: With this change, ALL invocations of ata_qc_complete() are now
done under host_set lock.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Interrupts from devices sharing the same IRQ could cause
ata_host_intr to finish commands being processed by atapi_packet_task
if the commands are using ATA_PROT_ATAPI_NODATA or ATA_PROT_ATAPI_DMA
protocol. This is because libata interrupt handler is unaware that
interrupts are not expected during that period. This patch adds
ATA_FLAG_NOINTR flag to tell the interrupt handler that we're not
expecting interrupts.
Note that once proper HSM is implemented for interrupt-driven PIO,
this should be merged into it and this flag will be removed.
ahci.c is a different kind of beast, so it's left alone.
* The following drivers use ata_qc_issue_prot and ata_interrupt, so
changes in libata core will do.
ata_piix sata_sil sata_svw sata_via sata_sis sata_uli
* The following drivers use ata_qc_issue_prot and custom intr handler.
They need this change to work correctly.
sata_nv sata_vsc
* The following drivers use custom issue function and intr handler.
Currently all custom issue functions don't support ATAPI, so this
change is irrelevant, updated for consistency and to avoid later
mistakes.
sata_promise sata_qstor sata_sx4
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Description:
After calling the completion callback, the libata error handler might be
running and getting atapi sense data. Clearing the ATA_QCFLAG_ACTIVE flag
at this point might interfere with the libata error handler.
Changes:
- Clear the ATA_QCFLAG_ACTIVE flag before calling the completion callback
(and also before the error handler)
- Add some comment
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PATCH 2/2: handle the case when device returns/needs extra data
Description:
Sometimes the device returns/needs extra data than expected.
Changes:
Modify __atapi_pio_bytes() to handle the case where device returns/needs extra data.
- for read case, discard trailing data from the device
- for write case, padding zero data to the device
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PATCH 1/2: ata_data_xfer() fix
Changes:
- Modify ata_mmio_data_xfer() and ata_pio_data_xfer() to handle odd-lengthed buffer.
- Add some function comments
This patch does not reuse ap->pad as alignment buffer since
using local variable seems good enough.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch lengthens the delay between DET setting and clearing for
COMMRESET from 400us to 1ms. I couldn't find any requiremen regarding
the duration of COMMRESET in SATA I/II specs but AHCI-1.1 10.4.2
states that it should be at least 1ms.
Signed-off-by: Tejun Heo <htejun@gmail.com>
scsi_add_host is the proper place to set the device, but people copy
the scsi_set_device usage from older drivers again and again.
note that this leaves some legacy drivers like qlogicisp/qlogicfc
without pci association in sysfs, but they're scheduled to go away soon
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>