As specified by errata eTSEC49 of MPC8548 and errata eTSEC12 of MPC83xx,
older revisions of gianfar controllers will be unable to calculate a TCP/UDP
packet checksum for some alignments of the appropriate FCB. This patch checks
for FCB alignment on such controllers and falls back to software checksumming
if the alignment is known to be bad.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of users of of_platform_driver in drivers/net. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
Just stumbled upon the issue while looking for another bug.
The code looks correct, the indentation is not.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (29 commits)
of/flattree: forward declare struct device_node in of_fdt.h
ipmi: explicitly include of_address.h and of_irq.h
sparc: explicitly cast negative phandle checks to s32
powerpc/405: Fix missing #{address,size}-cells in i2c node
powerpc/5200: dts: refactor dts files
powerpc/5200: dts: Change combatible strings on localbus
powerpc/5200: dts: remove unused properties
powerpc/5200: dts: rename nodes to prepare for refactoring dts files
of/flattree: Update dtc to current mainline.
of/device: Don't register disabled devices
powerpc/dts: fix syntax bugs in bluestone.dts
of: Fixes for OF probing on little endian systems
of: make drivers depend on CONFIG_OF instead of CONFIG_PPC_OF
of/flattree: Add of_flat_dt_match() helper function
of_serial: explicitly include of_irq.h
of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree
of/flattree: Reorder unflatten_dt_node
of/flattree: Refactor unflatten_dt_node
of/flattree: Add non-boottime device tree functions
of/flattree: Add Kconfig for EARLY_FLATTREE
...
Fix up trivial conflict in arch/sparc/prom/tree_32.c as per Grant.
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
Signed-off-by: Joe Perches <joe@perches.com>
irq_of_parse_and_map() has an unsigned return type.
Testing for a negative error value doesn't work here.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two identical implementations of of_get_mac_address(), one
each in arch/powerpc/kernel/prom_parse.c and
arch/microblaze/kernel/prom_parse.c. Move this function to a new
common file of_net.{c,h} and adjust all the callers to include the new
header.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
[grant.likely@secretlab.ca: protect header with #ifdef]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The rx_recycle queue is global per device but can be accesed by many
napi handlers at the same time, so it needs full skb_queue primitives
(with locking). Otherwise, various crashes caused by broken skbs are
possible.
This patch resolves, at least partly, bugzilla bug 19692. (Because of
some doubts that there could be still something around which is hard
to reproduce my proposal is to leave this bug opened for a month.)
Fixes commit: 0fd56bb5be ("gianfar: Add
support for skb recycling")
Reported-by: emin ak <eminak71@gmail.com>
Tested-by: emin ak <eminak71@gmail.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many (but not all) drivers check to see whether there is a vlan
group configured before using a tag stored in the skb. There's
not much point in this check since it just throws away data that
should only be present in the expected circumstances. However,
it will soon be legal and expected to get a vlan tag when no
vlan group is configured, so remove this check from all drivers
to avoid dropping the tags.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set num_tx_queues or real_num_tx_queues, since
alloc_etherdev_mq() does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the abstraction introduced by the union skb_shared_tx in
the shared skb data.
The access of the different union elements at several places led to some
confusion about accessing the shared tx_flags e.g. in skb_orphan_try().
http://marc.info/?l=linux-netdev&m=128084897415886&w=2
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device is just an alias for platform_device, so remove it entirely. Also
replace to_of_device() with to_platform_device() and update comment blocks.
This patch was initially generated from the following semantic patch, and then
edited by hand to pick up the bits that coccinelle didn't catch.
@@
@@
-struct of_device
+struct platform_device
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch relates to "[PATCH] gainfar.c : skb_over_panic
(kernel-2.6.32.15)"
While in 2.6.32.15 it actually fixed a bug here it merely cleans up
the previous attempts to fix the bug with a more coherent code.
Currently before queuing skb into the rx_recycle it is
"un-skb_reserve"-ed so when taken out in gfar_new_skb() it wont be
reserved twice.
This patch makes sure the alignment skb_reserve is done once, upon
allocating the skb and not when taken out of the rx_recycle
pool. Eliminating the need to undo anything before queue skb back to
the pool.
NOTE: This patch will compile and is fairly straight forward but I do
not have environment to test it as I did with the 2.6.32.15 fix.
Signed-off-by: Eran Liberty <liberty@extricom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC8313ECE says:
"If the controller receives a 1- or 2-byte frame (such as an illegal
runt packet or a packet with RX_ER asserted) before GRS is asserted
and does not receive any other frames, the controller may fail to set
GRSC even when the receive logic is completely idle. Any subsequent
receive frame that is larger than two bytes will reset the state so
the graceful stop can complete. A MAC receiver (Rx) reset will also
reset the state."
This patch implements the proposed workaround:
"If IEVENT[GRSC] is still not set after the timeout, read the eTSEC
register at offset 0xD1C. If bits 7-14 are the same as bits 23-30,
the eTSEC Rx is assumed to be idle and the Rx can be safely reset.
If the register fields are not equal, wait for another timeout
period and check again."
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC8313ECE says:
"For TOE=1 huge or jumbo frames, the data required to generate the
checksum may exceed the 2500-byte threshold beyond which the controller
constrains itself to one memory fetch every 256 eTSEC system clocks.
This throttling threshold is supposed to trigger only when the
controller has sufficient data to keep transmit active for the duration
of the memory fetches. The state machine handling this threshold,
however, fails to take large TOE frames into account. As a result,
TOE=1 frames larger than 2500 bytes often see excess delays before start
of transmission."
This patch implements the workaround as suggested by the errata
document, i.e.:
"Limit TOE=1 frames to less than 2500 bytes to avoid excess delays due to
memory throttling.
When using packets larger than 2700 bytes, it is recommended to turn TOE
off."
To be sure, we limit the TOE frames to 2500 bytes, and do software
checksumming instead.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC8313ECE says:
"If MACCFG2[Huge Frame]=0 and the Ethernet controller receives frames
which are larger than MAXFRM, the controller truncates the frames to
length MAXFRM and marks RxBD[TR]=1 to indicate the error. The controller
also erroneously marks RxBD[TR]=1 if the received frame length is MAXFRM
or MAXFRM-1, even though those frames are not truncated.
No truncation or truncation error occurs if MACCFG2[Huge Frame]=1."
There are two options to workaround the issue:
"1. Set MACCFG2[Huge Frame]=1, so no truncation occurs for invalid large
frames. Software can determine if a frame is larger than MAXFRM by
reading RxBD[LG] or RxBD[Data Length].
2. Set MAXFRM to 1538 (0x602) instead of the default 1536 (0x600), so
normal-length frames are not marked as truncated. Software can examine
RxBD[Data Length] to determine if the frame was larger than MAXFRM-2."
This patch implements the first workaround option by setting HUGEFRAME
bit, and gfar_clean_rx_ring() already checks the RxBD[Data Length].
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issuing the following command on host:
$ ifconfig eth2 mtu 1600 ; ping 10.0.0.27 -s 1485 -c 1
Makes some boards (tested with MPC8315 rev 1.1 and MPC8313 rev 1.0)
oops like this:
skb_over_panic: text:c0195914 len:1537 put:1537 head:c79e4800 data:c79e4880 tail:0xc79e4e81 end:0xc79e4e80 dev:eth1
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:127!
Oops: Exception in kernel mode, sig: 5 [#1]
MPC831x RDB
last sysfs file: /sys/kernel/uevent_seqnum
Modules linked in:
NIP: c01c1840 LR: c01c1840 CTR: c016d918
[...]
NIP [c01c1840] skb_over_panic+0x48/0x5c
LR [c01c1840] skb_over_panic+0x48/0x5c
Call Trace:
[c0339d50] [c01c1840] skb_over_panic+0x48/0x5c (unreliable)
[c0339d60] [c01c3020] skb_put+0x5c/0x60
[c0339d70] [c0195914] gfar_clean_rx_ring+0x25c/0x3d0
[c0339dc0] [c01976e8] gfar_poll+0x170/0x1bc
Dumped buffer descriptors showed that eTSEC's length/truncation
logic sometimes passes oversized packets, i.e. for the above ICMP
packet the following two buffer descriptors may become ready:
status=1400 length=1536
status=1800 length=1541
So, it seems that gianfar actually receives the whole big frame,
and it tries to place the packet into two BDs. This situation
confuses the driver, and so the skb_put() sanity check fails.
This patch fixes the issue by adding an appropriate check, i.e.
the driver should not try to process frames with buffer
descriptor's length over rx_buffer_size (i.e. maxfrm and mrblr).
Note that sometimes eTSEC works correctly, i.e. in the second
(last) buffer descriptor bits 'truncated' and 'crcerr' are set,
and so there's no oops. Though I couldn't find any logic when
it works correctly and when not.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the RCTRL_TS_ENABLE bit was set unconditionally. However, if
the RCTRL_TS_ENABLE is set without TMR_CTRL[TE], the driver does not work
properly on some boards (Anton had problems with the MPC8313ERDB and
MPC8568EMDS).
With this patch the bit will only be set if requested from user space
with the SIOCSHWTSTAMP ioctl command, meaning that time stamping is
disabled during normal operation. Users who are not interested in time
stamps will not experience problems with buggy CPU revisions or
performance drops any more.
The setting of TMR_CTRL[TE] is still up to the user. This is considered
safe because users wanting HW timestamps must initialize the eTSEC clock
first anyway, e.g. with the recently submitted PTP clock driver.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cc772ab7cd ("gianfar: Add
hardware RX timestamping support"), the driver no longer works on
at least MPC8313ERDB and MPC8568EMDS boards (and possibly much more
boards as well).
That's how MPC8313 Reference Manual describes RCTRL_TS_ENABLE bit:
Timestamp incoming packets as padding bytes. PAL field is set
to 8 if the PAL field is programmed to less than 8. Must be set
to zero if TMR_CTRL[TE]=0.
I see that the commit above sets this bit, but it doesn't handle
TMR_CTRL. Manfred probably had this bit set by the firmware for
his boards. But obviously this isn't true for all boards in the
wild.
Also, I recall that Freescale BSPs were explicitly disabling the
timestamping because of a performance drop.
For now, the best way to deal with this is just disable the
timestamping, and later we can discuss proper device tree bindings
and implement enabling this feature via some property.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
.name, .match_table and .owner are duplicated in both of_platform_driver
and device_driver. This patch is a removes the extra copies from struct
of_platform_driver and converts all users to the device_driver members.
This patch is a pretty mechanical change. The usage model doesn't change
and if any drivers have been missed, or if anything has been fixed up
incorrectly, then it will fail with a compile time error, and the fixup
will be trivial. This patch looks big and scary because it touches so
many files, but it should be pretty safe.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These callbacks were needed because dev_pm_ops support for OF
platform devices was in the powerpc tree, and the patch that
added dev_pm_ops for gianfar driver was in the netdev tree. Now
that netdev and powerpc trees have merged into Linus' tree, we
can remove the legacy hooks.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size for skbs which is added to the recycled list is using the
current descriptor size which is current MTU. gfar_new_skb() is also
using this size. So after changing or alteast increasing the MTU all
recycled skbs should be dropped.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gracefully stopping the controller, the driver was continuing if
*either* RX or TX had stopped. We need to wait for both, or the
controller could get into an invalid state.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gianfar driver may pass NULL pointer to the of_translate_address(),
which may lead to a kernel oops. Fix this by using of_iomap(), which
is also much simpler and shorter.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a packet has the skb_shared_tx->hardware flag set the device is
instructed to generate a TX timestamp and write it back to memory after
the frame is transmitted. During the clean_tx_ring operation the
timestamp will be extracted and copied into the skb_shared_hwtstamps
struct of the skb.
TX timestamping is enabled by setting the tx_type to something else
than HWTSTAMP_TX_OFF with the SIOCSHWTSTAMP ioctl command. It is only
supported by eTSEC devices.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device is configured to insert hardware timestamps into all
received packets. The RX timestamps are extracted from the padding
alingment bytes during the clean_rx_ring operation and copied into the
skb_shared_hwtstamps struct of the skb. This extraction only happens if
the rx_filter was set to something else than HWTSTAMP_FILTER_NONE with
the SIOCSHWTSTAMP ioctl command.
Hardware timestamping is only supported for eTSEC devices. To indicate
device support the new FSL_GIANFAR_DEV_HAS_TIMER flag was introduced.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix this:
eth2: :RX BD ring size for Q[0]: 256
eth2:TX BD ring size for Q[0]: 256
to look like:
eth2: RX BD ring size for Q[0]: 256
eth2: TX BD ring size for Q[0]: 256
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Dubov
Grant Likely
Linus Torvalds
Anton Vorontsov
Eric Dumazet
Joe Perches
Nicolas Kaiser
David Daney
Jarek Poplawski
Jesse Gross
Ben Hutchings
Oliver Hartkopp
Julia Lawall
Jiri Kosina
Richard Cochran
Eran Liberty
Anton Vorontsov
David S. Miller
Manfred Rudigier
Uwe Kleine-König
Sebastian Andrzej Siewior
Andy Fleming
Jiri Pirko
Kim Phillips