Commit Graph

52 Commits

Author SHA1 Message Date
David C Somayajulu 9d56291366 [SCSI] qla4xxx: fix scsi command completion, lun reset and target reset code
This patch contains the following:

1. when hba completion status is good, check for iscsi transport
   errors (underflow/overflow) prior to checking the scsi status

2. New firmware requires that one marker iocb be issued for each task
   management command. The patch issues marker iocb immediately
   following a LUN or Target reset.

Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-07 12:19:00 -05:00
Mike Christie ce5450392f [SCSI] qla4xxx: Add target reset functionality
This patch adds target reset functionalty.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-07 12:15:43 -05:00
Mike Christie 024f801f52 [SCSI] qla4xxx: regression - add start scan callout
We are seeing EXIST errors from sysfs during device addition.
We need a start scan callout so we do not start scanning sessions
found during hba setup, before the async scsi scan code is ready.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-03-05 12:03:54 -06:00
Mike Christie 50a29aec9c [SCSI] qla4xxx: fix host reset dpc race
The host reset callout could be starting to reset the hba at the same
time the dpc thread is. This creates lots of problems because they both
want to do wierd things with the firmware and interrupts, etc.

This patch just has the host reset function fully shutdown the dpc
thread before resetting the hba.

This patch also moves the setting of the session online bit to fix
a potential race with the dpc thread and iscsi recovery thread.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-03-05 12:03:17 -06:00
David Somayajulu 65fecc77f3 [SCSI] qla4xxx: fix up residual handling
the check in the residual case has an incorrect test of scsi_status
(the logic is reversed, it should be scsi_status != 0 instead of
!scsi_status.  Since we checked a few lines above that scsi_status was
non-zero, just eliminate this test

Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-22 17:14:12 -06:00
Mike Christie 921601b703 [SCSI] qla4xxx: add async scan support
qla4xxx has the old school startup/probe where it finds presetup sessions
in its flash and then attempts to log into them before returning from the
probe. This however, makes it very simple to add a iscsi class scan finished
helper which the driver can use.

In future patches Dave or I will rip apart the driver to make it more
like qla2xxx, but for now this is a very simple two line patch which
fixes the problem of trying to figure out when the initial sessions
are done being scanned.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-07 18:02:35 -06:00
Mike Christie 568d303b5b [SCSI] qla4xxx: fix recovery timer and session unblock race
If qla4xxx is resetting up a session and the recovery timer
fires we do not want to just set it to dead, because
the dpc thread could have just set it to online and is in the
middle of resetting it up.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-07 18:02:35 -06:00
Mike Christie 7fb1921b07 [SCSI] qla4xxx: use iscsi class session state check ready
This has qla4xxx use the iscsi class's check ready function
in the queue command function, so all iscsi drivers return the
same error value for common problems.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-07 18:02:35 -06:00
Mike Christie b635930de9 [SCSI] qla4xxx: directly call iscsi recovery functions
Qla4xxx can just call the iscsi recovery functions directly.
There is no need for userspace to do this for qla4xxx, because
we do not use the mutex to iterate over devices anymore and iscsi_block
/unblock_session can be called from interrupt context or the dpc thread.
And having userspace do this just creates uneeded headaches for qla4xxx root
situations where the session may experience problems. For example
during the kernel shutdown the scsi layer wants to send sync caches, but at
this time userspace is not up (iscsid is not running), so we cannot
recover from the problem.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-02-07 18:02:34 -06:00
Joe Perches b1c118121a drivers/scsi/: Spelling fixes
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: David Somayajulu <david.somayajulu@qlogic.com>
Acked-by: Mark Salyzyn <mark_salyzyn@adaptec.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
2008-02-03 17:28:22 +02:00
James Bottomley d3f46f39b7 [SCSI] remove use_sg_chaining
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.

Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-30 13:14:02 -06:00
Michael Chan 7ffc49a6ee [ETH]: Combine format_addr() with print_mac().
print_mac() used many most net drivers and format_addr() used by
net-sysfs.c are very similar and they can be intergrated.

format_addr() is also identically redefined in the qla4xxx iscsi
driver.

Export a new function sysfs_format_mac() to be used by net-sysfs,
qla4xxx and others in the future.  Both print_mac() and
sysfs_format_mac() call _format_mac_addr() to do the formatting.

Changed print_mac() to use unsigned char * to be consistent with
net_device struct's dev_addr.  Added buffer length overrun checking
as suggested by Joe Perches.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:00:05 -08:00
FUJITA Tomonori b80ca4f7ee [SCSI] replace sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE
This replaces sizeof sense_buffer with SCSI_SENSE_BUFFERSIZE in
several LLDs. It's a preparation for the future changes to remove
sense_buffer array in scsi_cmnd structure.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-23 11:29:27 -06:00
Mike Christie 2697478903 [SCSI] libiscsi: fix shutdown
We were using the device delete sysfs file to remove each device
then logout. Now in 2.6.21 this will not work because
the sysfs delete file returns immediately and does not wait for
the device removal to complete. This causes a hang if a cache sync
is needed during shutdown. Before .21, that approach had other
problems, so this patch fixes the shutdown code so that we remove the target
and unbind the session before logging out and shut down the session

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:28:33 -06:00
Robert P. J. Day 3a4fa0a25d Fix misspellings of "system", "controller", "interrupt" and "necessary".
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
2007-10-19 23:10:43 +02:00
Mathieu Desnoyers 1c3f0b8e07 Change struct marker users
Prior to use struct marker in the linux kernel markers, we need to clean
two drivers which use this structure name.

Change bonding driver types :
- struct marker to struct bond_marker.
- marker_t to bond_marker_t.
- marker_header to bond_marker_header.
- marker_header_t to bond_marker_header_t.

Change qla4xxx struct marker_entry usage :
- Change struct marker_entry for struct qla4_marker_entry.

Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Chad Tindel <ctindel@users.sourceforge.net>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: David Somayajulu <david.somayajulu@qlogic.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-19 11:53:53 -07:00
Joe Perches 898eb71cb1 Add missing newlines to some uses of dev_<level> messages
Found these while looking at printk uses.

Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk

Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-18 14:37:28 -07:00
FUJITA Tomonori 9cb83c7529 [SCSI] add use_sg_chaining option to scsi_host_template
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-16 11:24:32 +02:00
Paul Mundt 20c2df83d2 mm: Remove slab destructors from kmem_cache_create().
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.

This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2007-07-20 10:11:58 +09:00
David C Somayajulu 6ea7e33ee1 [SCSI] qla4xxx: Fix underrun/overrun conditions
On Wed, 2007-06-06 at 11:55 -0700, David C Somayajulu wrote:
This patch fixes the code handling underrun and overrun conditions.
Also fixed coding style as per Mike Christie's advice.

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-07-14 19:11:38 -05:00
David C Somayajulu 46235e600a [SCSI] qla4xxx: allow hba to be online when initiator ip address is uninitialized
This patch provides the following:

1. remove warning ignoring the return value of pci_set_mwi()
2. allows HBA to be online when the initiator ip address is uninitialized.

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-17 14:54:50 -05:00
Mike Christie d8196ed218 [SCSI] iscsi class, iscsi_tcp, iser, qla4xxx: add netdevname sysfs attr
iSCSI must support software iscsi (iscsi_tcp, iser), hardware iscsi (qla4xxx),
and partial offload (broadcom). To be able to allow each stack or driver
or port (virtual or physical) to be able to log into the same target portal
we use the initiator tuple [[HWADDRESS | NETDEVNAME], INITIATOR_NAME] and
the target tuple [TARGETNAME, CONN_ADDRESS, CONN_PORT] to id a session.
This patch adds the netdev name, which is used by software iscsi when
it binds a session to a netdevice using the SO_BINDTODEVICE sock opt.
It cannot use HWADDRESS because if someone did vlans then the same netdevice
will have the same mac and the initiator,target id will not be unique.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:38:04 -04:00
Mike Christie 2223696192 [SCSI] iscsi class, qla4xxx, iscsi_tcp: export local address
This patch exports the local address for the session. For
qla4xxx this is the ip of the hba's port. For software
this is the src addr of the socket.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:37:19 -04:00
Mike Christie 0ab823db86 [SCSI] qla4xxx: add iscsi_transport capps for fw capacilities
Userspace will want to know what the driver/FW/HW capabilites
when it comes to some operations like if the hardware can
do discovery or if it can store iscsi info like what target
was used for boot. This patch adds some new caps so userspace
can tell if the driver supports hardware/fw based sendtargets
discovery and if the hardware has some flash which may be
holding or can contain some iscsi target info
.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-02 15:36:14 -04:00
Mike Christie 8ad5781ae9 [SCSI] iscsi class, qla4xxx, iscsi_tcp, ib_iser: export/set initiator name
For iscsi root boot, software iscsi needs to know what the BIOS/OF
initiator used for the initiator name so this puts it in sysfs
for userspace to be able to pick up.

For hw iscsi, it is nice to see what the card is using.

This patch adds the new param, and hooks in qla4xxx, iscsi_tcp, and ib_iser.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:56:40 -04:00
Mike Christie 2174a04ee7 [SCSI] iscsi_transport, qla4xxx: have class lookup host for drivers
We are going to be adding more host level sysfs attrs and
set_params, so this patch has them take a scsi_host instead
of either a scsi_host or host no.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:23:12 -04:00
Mike Christie aa1e93a2fe [SCSI] qla4xxx: export mac as hw address
Export mac as hw address.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-06-01 12:15:36 -04:00
FUJITA Tomonori 5f7186c841 [SCSI] qla4xxx: convert to use the data buffer accessors
- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-29 18:32:12 -05:00
David C Somayajulu bee4fe8e63 [SCSI] qla4xxx: ql4_os.c bugfixes
Free memory resources after invoking free_irq() in
qla4xxx_free_adapter(). QLA4xxx has two pci functions per port
(Ethernet and iSCSI). When one of these PCI functions issues a HBA
reset, all other functions are notified and need to acknowledge and
re-initialize. During module qla4xxx_remove_adapter() gets
invoked. This function needs to wait if it is currently responding to
a reset from another function.

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:53 -05:00
David C Somayajulu c0e344c9b7 [SCSI] qla4xxx: ql4_mbx.c remove dead code bugfixes
All all inbound mbx registers for all mbx commands. Remove dead code.

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:49 -05:00
David C Somayajulu 401425b1ea [SCSI] qla4xxx: ql4_isr.c support for new mbx cmds
Add support to log all AENs and service mbx cmd completions for QLA4032

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:44 -05:00
David C Somayajulu e08c182cba [SCSI] qla4xxx: update rev num and misc cleanup
Clean up and update version number

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:40 -05:00
David C Somayajulu 92b7273608 [SCSI] qla4xxx: ql4_init.c bugfixes
In qla4xxx_get_ddb_entry() and qla4xxx_add_device_dynamically()
differentiate between a target which has been newly added vs a target
which went offline temporarily and is online again.  In
qla4xxx_build_ddb_list() firmware ddb state needs to be updated by
calling qla4xxx_get_ddb_entry(). Fix qla4x00_pci_config() and clean up
code.

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:35 -05:00
David C Somayajulu b285431657 [SCSI] qla4xxx: ql4_fw.h add support for qla4032
Add support for QLA4032 which supports IPv6

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:31 -05:00
David C Somayajulu 5c8bfc9449 [SCSI] qla4xxx: ql4_def.h log all AENs and cleanup
Add support for logging all AENs and clean up

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:27 -05:00
David C Somayajulu 0187106664 [SCSI] qla4xxx: ql4_dbg.c remove dead code
Remove dead code

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-26 11:47:22 -05:00
Adrian Bunk 4797547778 [SCSI] qla4xxx: possible cleanups
- make needlessly global code static
- #if 0 unused functions

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-05-06 09:33:16 -05:00
Thomas Gleixner 38515e908b [PATCH] Scheduled removal of SA_xxx interrupt flags fixups
The obsolete SA_xxx interrupt flags have been used despite the scheduled
removal.  Fixup the remaining users.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: James Simmons <jsimmons@infradead.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:54 -08:00
David C Somayajulu 477ffb9d87 [SCSI] qla4xxx: bug fixes
The included patch fixes the following issues:

1. qla3xxx/qla4xxx co-existence issue which can result in a lockup
when qla3xxx driver is unloaded, or when ifdown; ifup is performed on
one of the interfaces correponding to qla3xxx. This is because qla4xxx
HBA supports one ethernet and iscsi interfaces per port. Both iscsi
and ethernet interfaces share the same state machine. The problem has
to do with synchronizing access to the state machine in the event of a
reset

2. mutex_lock() is sometimes not followed by mutex_unlock() prior to
invoking a msleep() in qla4xxx_mailbox_command()

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2007-01-27 09:15:46 -06:00
Christoph Lameter e18b890bb0 [PATCH] slab: remove kmem_cache_t
Replace all uses of kmem_cache_t with struct kmem_cache.

The patch was generated using the following script:

	#!/bin/sh
	#
	# Replace one string by another in all the kernel sources.
	#

	set -e

	for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
		quilt add $file
		sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
		mv /tmp/$$ $file
		quilt refresh
	done

The script was run like this

	sh replace kmem_cache_t "struct kmem_cache"

Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:25 -08:00
David Howells 4796b71fbb Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/pcmcia/ds.c

Fix up merge failures with Linus's head and fix new compile failures.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-06 15:01:18 +00:00
David C Somayajulu 7feb6b3fbb [SCSI] qla4xxx: fix for timing issue for nvram accesses.
This patch fixes a timing issue related to nvram accesses in qla4xxx
driver for some cpu/slot speed combination.

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-11-22 12:17:10 -06:00
David C Somayajulu d915058f48 [SCSI] qla4xxx: add support for qla4032
This patch provides the following:

1. adds support for the next version of Qlogic's iSCSI HBA, qla4032
   (PCI Device ID 4032).

2. removes dead code related to topcat chip and renames
   qla4010_soft_reset to qla4xxx_soft_reset (minor changes).

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-11-22 12:14:04 -06:00
David C Somayajulu f26b90440c [PATCH] qla4xxx: bug fix: driver hardware semaphore needs to be grabbed before soft reset
On qla4xxx, the driver needs to grab the drvr semaphore provided by
the hardware, prior to issuing a reset. This patches takes care of a
couple of places where it was not being done. In addition there is
minor clean up.

Signed-off-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-11-22 11:21:13 -06:00
David Howells c4028958b6 WorkStruct: make allyesconfig
Fix up for make allyesconfig.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-11-22 14:57:56 +00:00
Randy Dunlap 80fc115d46 [PATCH] SCSI: ISCSI build failure
SCSI_QLA_ISCSI needs to depend on NET to prevent build (link) failures
that are caused by selecting SCSI_ISCSI_ATTRS.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-31 08:13:19 -08:00
Andrew Vasquez 11010fecd2 [SCSI] Maintain module-parameter name consistency with qla2xxx/qla4xxx.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-10-25 15:12:17 -07:00
Doug Maxey 5ae16db369 [SCSI] qla4xxx: fix double printk on load
There is a dup printk at the tail of qla4xxx_module_init().  Remove the
first instance as it's before the complete success of the function.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2006-10-25 15:12:07 -07:00
Linus Torvalds 44aefd2706 Merge git://git.infradead.org/~dhowells/irq-2.6
* git://git.infradead.org/~dhowells/irq-2.6:
  IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
  IRQ: Typedef the IRQ handler function type
  IRQ: Typedef the IRQ flow handler function type
2006-10-05 16:32:01 -07:00
Frederik Deweerdt d7a297baa6 [PATCH] fix qla{2,4} build error
commit 0181944fe6 adds a
'extended_error_logging' global variable to qla2xxx which is defined by
qla4xxx too.

Trying to build both drivers results in the following error:

  LD      drivers/scsi/built-in.o
  drivers/scsi/qla4xxx/built-in.o: In function `qla4xxx_slave_configure':
  drivers/scsi/qla4xxx/ql4_os.c:1433: multiple definition of `extended_error_logging'
  drivers/scsi/qla2xxx/built-in.o:drivers/scsi/qla2xxx/qla_os.c:2166:
  first defined here
  make[2]: *** [drivers/scsi/built-in.o] Error 1
  make[1]: *** [drivers/scsi] Error 2
  make: *** [drivers] Error 2

The following patch simply adds a qla2_ (qla4_ respectively) prefix to
the variable name.

Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-05 15:49:02 -07:00