* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (47 commits)
perf report: Add --symbols parameter
perf report: Add --comms parameter
perf report: Add --dsos parameter
perf_counter tools: Adjust only prelinked symbol's addresses
perf_counter: Provide a way to enable counters on exec
perf_counter tools: Reduce perf stat measurement overhead/skew
perf stat: Use percentages for scaling output
perf_counter, x86: Update x86_pmu after WARN()
perf stat: Micro-optimize the code: memcpy is only required if no event is selected and !null_run
perf stat: Improve output
perf stat: Fix multi-run stats
perf stat: Add -n/--null option to run without counters
perf_counter tools: Remove dead code
perf_counter: Complete counter swap
perf report: Print sorted callchains per histogram entries
perf_counter tools: Prepare a small callchain framework
perf record: Fix unhandled io return value
perf_counter tools: Add alias for 'l1d' and 'l1i'
perf-report: Add bare minimum PERF_EVENT_READ parsing
perf-report: Add modes for inherited stats and no-samples
...
Add a mutex to avoid a circular locking problem between the mm layer
semaphore and fbdev ioctl mutex through the fb_mmap() call.
Also, add mutex to all places where smem_start and smem_len fields change
so the mutex inside the fb_mmap() is actually used. Changing of these
fields before calling the framebuffer_register() are not mutexed.
This is 2.6.31 material. It removes one lockdep (fb_mmap() and
register_framebuffer()) but there is still another one (fb_release() and
register_framebuffer()). It also cleans up handling of the smem_start and
smem_len fields used by mutexed section of the fb_mmap().
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new spi_master.flags word listing constraints relevant to that
controller. Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.
Have the mmc_spi host be the first customer of this flag. Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.
(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies. Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:
* SPI_NO_CS ... a second 3-wire variant, where the chipselect
line is removed instead of a data line; transfers are still
full duplex.
This obviously has STRONG protocol implications since the
chipselect transitions can't be used to synchronize state
transitions with the SPI master.
* SPI_READY ... defines open drain signal that's pulled low
to pause the clock. This defines a 5-wire variant (normal
4-wire SPI plus READY) and two 4-wire variants (READY plus
each of the 3-wire flavors).
Such hardware flow control can be a big win. There are ADC
converters and flash chips that expose READY signals, but not
many host controllers support it today.
The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack. That's a mode most hardware can easily support
(unlike SPI_READY).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With ELF, at generating coredump, some more headers other than used
vmas are added.
When max_map_count == 65536, a core generated by following kinds of
code can be unreadable because the number of ELF's program header is
written in 16bit in Ehdr (please see elf.h) and the number overflows.
==
... = mmap(); (munmap, mprotect, etc...)
if (failed)
abort();
==
This can happen in mmap/munmap/mprotect/etc...which calls split_vma().
I think 65536 is not safe as _default_ and reduce it to 65530 is good
for avoiding unexpected corrupted core.
Anyway, max_map_count can be enlarged by sysctl if a user is brave..
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Jakub Jelinek <jakub@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
alpha percpu access requires custom SHIFT_PERCPU_PTR() definition for
modules to work around addressing range limitation. This is done via
generating inline assembly using C preprocessing which forces the
assembler to generate external reference. This happens behind the
compiler's back and makes the compiler think that static percpu variables
in modules are unused.
This used to be worked around by using __unused attribute for percpu
variables which prevent the compiler from omitting the variable; however,
recent declare/definition attribute unification change broke this as
__used can't be used for declaration. Also, in the process,
PER_CPU_ATTRIBUTES definition in alpha percpu.h got broken.
This patch adds PER_CPU_DEF_ATTRIBUTES which is only used for definitions
and make alpha use it to add __used for percpu variables in modules. This
also fixes the PER_CPU_ATTRIBUTES double definition bug.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: maximilian attems <max@stro.at>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ctors section for each object file is eight byte aligned (on 64 bit).
However the __ctors_start symbol starts at an arbitrary address dependent
on the size of the previous sections.
Therefore the linker may add some zeroes after __ctors_start to make sure
the ctors contents are properly aligned. However the extra zeroes at the
beginning aren't expected by the code. When walking the functions
pointers contained in there and extra zeroes are added this may result in
random jumps. So make sure that the __ctors_start symbol is always
aligned as well.
Fixes this crash on an allyesconfig on s390:
[ 0.582482] Kernel BUG at 0000000000000012 [verbose debug info unavailable]
[ 0.582489] illegal operation: 0001 [#1] SMP DEBUG_PAGEALLOC
[ 0.582496] Modules linked in:
[ 0.582501] CPU: 0 Tainted: G W 2.6.31-rc1-dirty #273
[ 0.582506] Process swapper (pid: 1, task: 000000003f218000, ksp: 000000003f2238e8)
[ 0.582510] Krnl PSW : 0704200180000000 0000000000000012 (0x12)
[ 0.582518] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:2 PM:0 EA:3
[ 0.582524] Krnl GPRS: 0000000000036727 0000000000000010 0000000000000001 0000000000000001
[ 0.582529] 00000000001dfefa 0000000000000000 0000000000000000 0000000000000040
[ 0.582534] 0000000001fff0f0 0000000001790628 0000000002296048 0000000002296048
[ 0.582540] 00000000020c438e 0000000001786000 0000000002014a66 000000003f223e60
[ 0.582553] Krnl Code:>0000000000000012: 0000 unknown
[ 0.582559] 0000000000000014: 0000 unknown
[ 0.582564] 0000000000000016: 0000 unknown
[ 0.582570] 0000000000000018: 0000 unknown
[ 0.582575] 000000000000001a: 0000 unknown
[ 0.582580] 000000000000001c: 0000 unknown
[ 0.582585] 000000000000001e: 0000 unknown
[ 0.582591] 0000000000000020: 0000 unknown
[ 0.582596] Call Trace:
[ 0.582599] ([<0000000002014a46>] kernel_init+0x622/0x7a0)
[ 0.582607] [<0000000000113e22>] kernel_thread_starter+0x6/0xc
[ 0.582615] [<0000000000113e1c>] kernel_thread_starter+0x0/0xc
[ 0.582621] INFO: lockdep is turned off.
[ 0.582624] Last Breaking-Event-Address:
[ 0.582627] [<0000000002014a64>] kernel_init+0x640/0x7a0
Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the eventfd interface to de-couple the eventfd memory context, from
the file pointer instance.
Without such change, there is no clean way to racely free handle the
POLLHUP event sent when the last instance of the file* goes away. Also,
now the internal eventfd APIs are using the eventfd context instead of the
file*.
This patch is required by KVM's IRQfd code, which is still under
development.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Gregory Haskins <ghaskins@novell.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add notification messages that allow the filesystem to invalidate VFS
caches.
Two notifications are added:
1) inode invalidation
- invalidate cached attributes
- invalidate a range of pages in the page cache (this is optional)
2) dentry invalidation
- try to invalidate a subtree in the dentry cache
Care must be taken while accessing the 'struct super_block' for the
mount, as it can go away while an invalidation is in progress. To
prevent this, introduce a rw-semaphore, that is taken for read during
the invalidation and taken for write in the ->kill_sb callback.
Cc: Csaba Henk <csaba@gluster.com>
Cc: Anand Avati <avati@zresearch.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
This patch lets filesystems handle masking the file mode on creation.
This is needed if filesystem is using ACLs.
- The CREATE, MKDIR and MKNOD requests are extended with a "umask"
parameter.
- A new FUSE_DONT_MASK flag is added to the INIT request/reply. With
this the filesystem may request that the create mode is not masked.
CC: Jean-Pierre André <jean-pierre.andre@wanadoo.fr>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
This provides a way to mark a counter to be enabled on the next
exec. This is useful for measuring the total activity of a
program without including overhead from the process that
launches it.
This also changes the perf stat command to use this new
facility.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <19017.43927.838745.689203@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-2.6:
ide: memory overrun in ide_get_identity_ioctl() on big endian machines using ioctl HDIO_OBSOLETE_IDENTITY
ide: fix resume for CONFIG_BLK_DEV_IDEACPI=y
ide-cd: handle fragmented packet commands gracefully
ide: always kill the whole request on error
ide: fix ide_kill_rq() for special ide-{floppy,tape} driver requests
commit 2f0d0fd2a6 ("ide-acpi: cleanup
do_drive_get_GTF()") didn't account for the lack of hwif->acpidata
check in generic_ide_suspend() [ indirect user of do_drive_get_GTF()
through ide_acpi_exec_tfs() ] resulting in broken resume when ACPI
support is enabled but ACPI data is unavailable.
Fix it by adding ide_port_acpi() helper for checking if port needs
ACPI handling and cleaning generic_ide_{suspend,resume}() to use it
instead of hiding hwif->acpidata and ide_noacpi checks in IDE ACPI
helpers (this should help in preventing similar bugs in the future).
While at it:
- kill superfluous debugging printks in ide_acpi_{get,push}_timing()
Reported-and-tested-by: Etienne Basset <etienne.basset@numericable.fr>
Also-reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this function should never modify it (saves warnings when called with
const args too).
Signed-off-by: Alexey Zaytsev <zaytsev@altell.ru>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The new fsnotify infrastructure (starting at 90586523) causes an oops in
spufs, where we populate a directory with files before instantiating the
directory itself. The new changes seem to have introduced an assumption
that a dentry's parent will be positive when instantiating.
This change makes it once again possible to d_instantiate a dentry
with a negative parent, and brings __fsnotify_d_instantiate() into
line with inotify_d_instantiate(), which already has this NULL check.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
As reported by Philip, the UNTRACKED state bit does not fit within
the 8-bit state_mask member. Enlarge state_mask and give status_mask
a few more bits too.
Reported-by: Philip Craig <philipc@snapgear.com>
References: http://markmail.org/thread/b7eg6aovfh4agyz7
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
fix the following 'make headers_check' warnings:
usr/include/linux/netfilter/xt_osf.h:40: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When NAT helpers change the TCP packet size, the highest seen sequence
number needs to be corrected. This is currently only done upwards, when
the packet size is reduced the sequence number is unchanged. This causes
TCP conntrack to falsely detect unacknowledged data and decrease the
timeout.
Fix by updating the highest seen sequence number in both directions after
packet mangling.
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Original patch by Marek Vasut, modified by Eric in:
1. use delayed work to simplify the debouncing
2. combine col_polarity/row_polarity into a single active_low field
3. use a generic bit array based XOR algorithm to detect key
press/release, which should make the column assertion time
shorter and code a bit cleaner
4. remove the ALT_FN handling, which is no way generic, the ALT_FN
key should be treated as no different from other keys, and
translation will be done by user space by commands like 'loadkeys'.
5. explicitly disable row IRQs and flush potential pending work,
and schedule an immediate scan after resuming as suggested
by Uli Luckas
6. incorporate review comments from many others
Patch tested on Littleton/PXA310 (though PXA310 has a dedicate keypad
controller, I have to configure those pins as generic GPIO to use this
driver, works quite well, though), and Sharp Zaurus model SL-C7x0
and SL-C1000.
[dtor@mail.ru: fix error unwinding path, support changing keymap
from userspace]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Trilok Soni <soni.trilok@gmail.com>
Reviewed-by: Uli Luckas <u.luckas@road.de>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
be2net: Fix to avoid a crash seen on PPC with LRO and Jumbo frames.
gro: Flush GRO packets in napi_disable_pending path
inet: Call skb_orphan before tproxy activates
mac80211: Use rcu_barrier() on unload.
sunrpc: Use rcu_barrier() on unload.
bridge: Use rcu_barrier() instead of syncronize_net() on unload.
ipv6: Use rcu_barrier() on module unload.
decnet: Use rcu_barrier() on module unload.
sky2: Fix checksum endianness
mdio add missing GPL flag
sh_eth: remove redundant test on unsigned
fsl_pq_mdio: Fix fsl_pq_mdio to work with modules
ipv6: avoid wraparound for expired preferred lifetime
tcp: missing check ACK flag of received segment in FIN-WAIT-2 state
atl1*: add device_set_wakeup_enable to atl1*_set_wol
Phonet: generate Netlink RTM_DELADDR when destroying a device
Phonet: publicize the Netlink notification function
Revert "veth: prevent oops caused by netdev destructor"
cpmac: fix compilation failure introduced with netdev_ops conversion
ipsec: Fix name of CAST algorithm
This patch fixes an imbalance message as reported by J.R. Okajima.
The IMA file counters are incremented in ima_path_check. If the
actual open fails, such as ETXTBSY, decrement the counters to
prevent unnecessary imbalance messages.
Reported-by: J.R. Okajima <hooanon05@yahoo.co.jp>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: shut up uninit compiler warning in paging_tmpl.h
KVM: Ignore reads to K7 EVNTSEL MSRs
KVM: VMX: Handle vmx instruction vmexits
KVM: s390: Allow stfle instruction in the guest
KVM: kvm/x86_emulate.c toggle_interruptibility() should be static
KVM: ia64: fix ia64 build due to missing kallsyms_lookup() and double export
KVM: protect concurrent make_all_cpus_request
KVM: MMU: Allow 4K ptes with bit 7 (PAT) set
KVM: Fix dirty bit tracking for slots with large pages
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, delay: tsc based udelay should have rdtsc_barrier
x86, setup: correct include file in <asm/boot.h>
x86, setup: Fix typo "CONFIG_x86_64" in <asm/boot.h>
x86, mce: percpu mcheck_timer should be pinned
x86: Add sysctl to allow panic on IOCK NMI error
x86: Fix uv bau sending buffer initialization
x86, mce: Fix mce resume on 32bit
x86: Move init_gbpages() to setup_arch()
x86: ensure percpu lpage doesn't consume too much vmalloc space
x86: implement percpu_alloc kernel parameter
x86: fix pageattr handling for lpage percpu allocator and re-enable it
x86: reorganize cpa_process_alias()
x86: prepare setup_pcpu_lpage() for pageattr fix
x86: rename remap percpu first chunk allocator to lpage
x86: fix duplicate free in setup_pcpu_remap() failure path
percpu: fix too lazy vunmap cache flushing
x86: Set cpu_llc_id on AMD CPUs
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timer stats: Optimize by adding quick check to avoid function calls
timers: Fix timer_migration interface which accepts any number as input
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Futher document blink_set
leds: Add options to have GPIO LEDs start on or keep their state
leds: LED driver for National Semiconductor LP3944 Funlight Chip
leds: pca9532 - Indent using tabs, not spaces.
leds: Remove an orphan Kconfig entry
leds: Further document parameters for blink_set()
leds: alix-leds2 fixed for Award BIOS
leds: leds-gpio - fix a section mismatch
leds: add the sysfs interface into the leds-bd2802 driver for changing wave pattern and led current.
leds: change the license information
leds: fix led-bd2802 errors while resuming
make_all_cpus_request contains a race condition which can
trigger false request completed status, as follows:
CPU0 CPU1
if (test_and_set_bit(req,&vcpu->requests))
.... if (test_and_set_bit(req,&vcpu->requests))
.. return
proceed to smp_call_function_many(wait=1)
Use a spinlock to serialize concurrent CPUs.
Cc: stable@kernel.org
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch is preparation for replacing most ".data.init_task" in the
kernel with macros, so that the section name can later be changed
without having to touch a lot of the kernel.
The long-term goal here is to be able to change the kernel's magic
section names to those that are compatible with -ffunction-sections
-fdata-sections. This requires renaming all magic sections with names
of the form ".data.foo".
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
We recently added a INIT_TASK(align) in include/asm-generic/vmlinux.lds.h,
but there is already a macro INIT_TASK in include/linux/init_task.h, which
is quite confusing. We should switch the macro in the linker script to
INIT_TASK_DATA. (Sorry that I missed this in reviewing the patch). Since
the macros are new, there is only one user of the INIT_TASK in
vmlinux.lds.h, arch/mn10300/kernel/vmlinux.lds.S.
However, we are currently using INIT_TASK_DATA for laying down an entire
.data.init_task section. So rename that to INIT_TASK_DATA_SECTION.
I would be worried about changing the meaning of INIT_TASK_DATA, but the
old INIT_TASK_DATA implementation had no users, and in fact if anyone had
tried to use it, it would have failed to compile because it didn't pass
the alignment to the old INIT_TASK.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch is preparation for replacing most uses of
".bss.page_aligned" and ".data.page_aligned" in the kernel with
macros, so that the section name can later be changed without having
to touch a lot of the kernel.
The long-term goal here is to be able to change the kernel's magic
section names to those that are compatible with -ffunction-sections
-fdata-sections. This requires renaming all magic sections with names
of the form ".data.foo".
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
RW_DATA_SECTION is defined to take 4 different alignment parameters,
while NOSAVE_DATA currently uses a fixed PAGE_SIZE alignment as noted
in the comments.
There are presently no in-tree users of this at present, and I just
stumbled across this while implementing the simplified script on a new
architecture port, which subsequently resulted in a syntax error.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_kill_rq()
and ide_floppy_do_request() for failed requests.
[ bugfix part ]
* Use blk_rq_bytes() instead of obsolete ide_rq_bytes() in ide_do_devset()
and ide_complete_drive_reset(). Then remove ide_rq_bytes().
[ cleanup part ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (28 commits)
drm: remove unused #include <linux/version.h>'s
drm/radeon: fix driver initialization order so radeon kms can be builtin
drm: Fix shifts which were miscalculated when converting from bitfields.
drm/radeon: Clear surface registers at initialization time.
drm/radeon: Don't initialize acceleration related fields of struct fb_info.
drm/radeon: fix radeon kms framebuffer device
drm/i915: initialize fence registers to zero when loading GEM
drm/i915: Fix HDMI regression introduced in new chipset support
drm/i915: fix LFP data fetch
drm/i915: set TV detection mode when tv is already connected
drm/i915: Catch up to obj_priv->page_list rename in disabled debug code.
drm/i915: Fix size_t handling in off-by-default debug printfs
drm/i915: Don't change the blank/sync width when calculating scaled modes
drm/i915: Add support for changing LVDS panel fitting using an output property.
drm/i915: correct suspend/resume ordering
drm/i915: Add missing dependency on Intel AGP support.
drm/i915: Generate 2MHz clock for display port aux channel I/O. Retry I/O.
drm/i915: Clarify error returns from display port aux channel I/O
drm/i915: Add CLKCFG register definition
drm/i915: Split array of DAC limits into separate structures.
...
This patch introduces a new sysctl:
/proc/sys/kernel/panic_on_io_nmi
which defaults to 0 (off).
When enabled, the kernel panics when the kernel receives an NMI
caused by an IO error.
The IO error triggered NMI indicates a serious system
condition, which could result in IO data corruption. Rather
than contiuing, panicing and dumping might be a better choice,
so one can figure out what's causing the IO error.
This could be especially important to companies running IO
intensive applications where corruption must be avoided, e.g. a
bank's databases.
[ SuSE has been shipping it for a while, it was done at the
request of a large database vendor, for their users. ]
Signed-off-by: Kurt Garloff <garloff@suse.de>
Signed-off-by: Roberto Angelino <robertangelino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
LKML-Reference: <20090624213211.GA11291@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The PERF_EVENT_READ implementation made me realize we don't
actually need the sample_type int the output sample, since
we already have that in the perf_counter_attr information.
Therefore, remove the PERF_EVENT_MISC_OVERFLOW bit and the
event->type overloading, and imply put counter overflow
samples in a PERF_EVENT_SAMPLE type.
This also fixes the issue that event->type was only 32-bit
and sample_type had 64 usable bits.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the introduction of PERF_EVENT_READ we have the
possibility to provide accurate counter values for
individual tasks in a task hierarchy.
However, due to the lazy context switching used for similar
counter contexts our current per task counts are way off.
In order to maintain some of the lazy switch benefits we
don't disable it out-right, but simply iterate the active
counters and flip the values between the contexts.
This only reads the counters but does not need to reprogram
the full PMU.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Provide a read() like event which can be used to log the
counter value at specific sites such as child->parent
folding on exit.
In order to be useful, we log the counter parent ID, not the
actual counter ID, since userspace can only relate parent
IDs to perf_counter_attr constructs.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add the needed time scale to the self-profile mmap information.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since there are two distinct sections to the control page,
move them apart so that possible extentions don't overlap.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the 4th parameter of get_user_pages() is called len, but its
in pages, not bytes. Rename the thing to nr_pages to avoid future
confusion.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt. Convert the two cases of on-stack packet
payload buffers in firewire-core (payload of lock requests in the bus
manager work and in iso resource management) to slab-allocated memory.
There are a number on-stack buffers for quadlet write or quadlet read
requests in firewire-core and firewire-sbp2. These are harmless; they
are copied to/ from card driver internal DMA buffers since quadlet
payloads are inlined with packet headers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.infradead.org/battery-2.6:
da9030_battery: Fix race between event handler and monitor
Add MAX17040 Fuel Gauge driver
w1: ds2760_battery: add support for sleep mode feature
w1: ds2760: add support for EEPROM read and write
ds2760_battery: cleanups in ds2760_battery_probe()
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (48 commits)
dm mpath: change to be request based
dm: disable interrupt when taking map_lock
dm: do not set QUEUE_ORDERED_DRAIN if request based
dm: enable request based option
dm: prepare for request based option
dm raid1: add userspace log
dm: calculate queue limits during resume not load
dm log: fix create_log_context to use logical_block_size of log device
dm target:s introduce iterate devices fn
dm table: establish queue limits by copying table limits
dm table: replace struct io_restrictions with struct queue_limits
dm table: validate device logical_block_size
dm table: ensure targets are aligned to logical_block_size
dm ioctl: support cookies for udev
dm: sysfs add suspended attribute
dm table: improve warning message when devices not freed before destruction
dm mpath: add service time load balancer
dm mpath: add queue length load balancer
dm mpath: add start_io and nr_bytes to path selectors
dm snapshot: use barrier when writing exception store
...
* 'audit.b63' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
Fix rule eviction order for AUDIT_DIR
Audit: clean up all op= output to include string quoting
Audit: move audit_get_nd completely into audit_watch
audit: seperate audit inode watches into a subfile
Audit: clean up audit_receive_skb
Audit: cleanup netlink mesg handling
Audit: unify the printk of an skb when auditd not around
Audit: dereferencing krule as if it were an audit_watch
Audit: better estimation of execve record length
Audit: fix audit watch use after free
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (72 commits)
asus-laptop: remove EXPERIMENTAL dependency
asus-laptop: use pr_fmt and pr_<level>
eeepc-laptop: cpufv updates
eeepc-laptop: sync eeepc-laptop with asus_acpi
asus_acpi: Deprecate in favor of asus-laptop
acpi4asus: update MAINTAINER and KConfig links
asus-laptop: platform dev as parent for led and backlight
eeepc-laptop: enable camera by default
ACPI: Rename ACPI processor device bus ID
acerhdf: Acer Aspire One fan control
ACPI: video: DMI workaround broken Acer 7720 BIOS enabling display brightness
ACPI: run ACPI device hot removal in kacpi_hotplug_wq
ACPI: Add the reference count to avoid unloading ACPI video bus twice
ACPI: DMI to disable Vista compatibility on some Sony laptops
ACPI: fix a deadlock in hotplug case
Show the physical device node of backlight class device.
ACPI: pdc init related memory leak with physical CPU hotplug
ACPI: pci_root: remove unused dev/fn information
ACPI: pci_root: simplify list traversals
ACPI: pci_root: use driver data rather than list lookup
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (23 commits)
switch xfs to generic acl caching helpers
helpers for acl caching + switch to those
switch shmem to inode->i_acl
switch reiserfs to inode->i_acl
switch reiserfs to usual conventions for caching ACLs
reiserfs: minimal fix for ACL caching
switch nilfs2 to inode->i_acl
switch btrfs to inode->i_acl
switch jffs2 to inode->i_acl
switch jfs to inode->i_acl
switch ext4 to inode->i_acl
switch ext3 to inode->i_acl
switch ext2 to inode->i_acl
add caching of ACLs in struct inode
fs: Add new pre-allocation ioctls to vfs for compatibility with legacy xfs ioctls
cleanup __writeback_single_inode
... and the same for vfsmount id/mount group id
Make allocation of anon devices cheaper
update Documentation/filesystems/Locking
devpts: remove module-related code
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6:
bnx2: Fix the behavior of ethtool when ONBOOT=no
qla3xxx: Don't sleep while holding lock.
qla3xxx: Give the PHY time to come out of reset.
ipv4 routing: Ensure that route cache entries are usable and reclaimable with caching is off
net: Move rx skb_orphan call to where needed
ipv6: Use correct data types for ICMPv6 type and code
net: let KS8842 driver depend on HAS_IOMEM
can: let SJA1000 driver depend on HAS_IOMEM
netxen: fix firmware init handshake
netxen: fix build with without CONFIG_PM
netfilter: xt_rateest: fix comparison with self
netfilter: xt_quota: fix incomplete initialization
netfilter: nf_log: fix direct userspace memory access in proc handler
netfilter: fix some sparse endianess warnings
netfilter: nf_conntrack: fix conntrack lookup race
netfilter: nf_conntrack: fix confirmation race condition
netfilter: nf_conntrack: death_by_timeout() fix
helpers: get_cached_acl(inode, type), set_cached_acl(inode, type, acl),
forget_cached_acl(inode, type).
ubifs/xattr.c needed includes reordered, the rest is a plain switchover.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch adds ioctls to vfs for compatibility with legacy XFS
pre-allocation ioctls (XFS_IOC_*RESVP*). The implementation
effectively invokes sys_fallocate for the new ioctls.
Also handles the compat_ioctl case.
Note: These legacy ioctls are also implemented by OCFS2.
[AV: folded fixes from hch]
Signed-off-by: Ankit Jain <me@ankitjain.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
When the kernel is configured with CONFIG_TIMER_STATS but timer
stats are runtime disabled we still get calls to
__timer_stats_timer_set_start_info which initializes some
fields in the corresponding struct timer_list.
So add some quick checks in the the timer stats setup functions
to avoid function calls to __timer_stats_timer_set_start_info
when timer stats are disabled.
In an artificial workload that does nothing but playing ping
pong with a single tcp packet via loopback this decreases cpu
consumption by 1 - 1.5%.
This is part of a modified function trace output on SLES11:
perl-2497 [00] 28630647177732388 [+ 125]: sk_reset_timer <-tcp_v4_rcv
perl-2497 [00] 28630647177732513 [+ 125]: mod_timer <-sk_reset_timer
perl-2497 [00] 28630647177732638 [+ 125]: __timer_stats_timer_set_start_info <-mod_timer
perl-2497 [00] 28630647177732763 [+ 125]: __mod_timer <-mod_timer
perl-2497 [00] 28630647177732888 [+ 125]: __timer_stats_timer_set_start_info <-__mod_timer
perl-2497 [00] 28630647177733013 [+ 93]: lock_timer_base <-__mod_timer
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mustafa Mesanovic <mustafa.mesanovic@de.ibm.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20090623153811.GA4641@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are some broken devices that report multiple DMA xfer modes
enabled at once (ATA spec doesn't allow it) but otherwise work fine
with DMA so just delete ide_id_dma_bug().
[ As discovered by detective work by Frans and Bart, due to how
handling of the ID block was handled before commit c419993
("ide-iops: only clear DMA words on setting DMA mode") this
check was always seeing zeros in the fields or other similar
garbage. Therefore this check wasn't actually checking anything.
Now that the tests actually check the real bits, all we see are
devices that trigger the check yet work perfectly fine, therefore
killing this useless check is the best thing to do. -DaveM ]
Reported-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like I managed to mess up most shifts when converting from bitfields. :(
The patch below works on my Thinkpad T500 (as well as on my PowerBook,
where the previous change worked as well, maybe out of luck...). I'd
appreciate more testing and eyes looking over it though.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Tested-by: Michael Pyne <mpyne@kde.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
A number of places in the audit system we send an op= followed by a string
that includes spaces. Somehow this works but it's just wrong. This patch
moves all of those that I could find to be quoted.
Example:
Change From: type=CONFIG_CHANGE msg=audit(1244666690.117:31): auid=0 ses=1
subj=unconfined_u:unconfined_r:auditctl_t:s0-s0:c0.c1023 op=remove rule
key="number2" list=4 res=0
Change To: type=CONFIG_CHANGE msg=audit(1244666690.117:31): auid=0 ses=1
subj=unconfined_u:unconfined_r:auditctl_t:s0-s0:c0.c1023 op="remove rule"
key="number2" list=4 res=0
Signed-off-by: Eric Paris <eparis@redhat.com>
Sometimes both acpi video and i915 driver are compiled as modules.
And there exists the strict dependency between the two drivers.
The acpi video bus will be unloaded in course of unloading the i915 driver.
If we unload the acpi video driver, then the kernel oops will be triggered.
Add the reference count to avoid unloading the ACPI video bus twice.
The reference count should be checked before unregistering the acpi video bus.
If the reference count is already zero, it won't unregister it again.
And after the acpi video bus is already unregistered, the reference count
will be set to zero.
http://bugzilla.kernel.org/show_bug.cgi?id=13396
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.infradead.org/iommu-2.6:
Intel-IOMMU, intr-remap: source-id checking
Intel-IOMMU, intr-remap: set the whole 128bits of irte when modify/free it
IOMMU Identity Mapping Support (drivers/pci/intel_iommu.c)
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2/trivial: Wrap ocfs2_sysfile_cluster_lock_key within define.
ocfs2: Add lockdep annotations
vfs: Set special lockdep map for dirs only if not set by fs
ocfs2: Disable orphan scanning for local and hard-ro mounts
ocfs2: Do not initialize lvb in ocfs2_orphan_scan_lock_res_init()
ocfs2: Stop orphan scan as early as possible during umount
ocfs2: Fix ocfs2_osb_dump()
ocfs2: Pin journal head before accessing jh->b_committed_data
ocfs2: Update atime in splice read if necessary.
ocfs2: Provide the ocfs2_dlm_lvb_valid() stack API.
In order to get the tun driver to account packets, we need to be
able to receive packets with destructors set. To be on the safe
side, I added an skb_orphan call for all protocols by default since
some of them (IP in particular) cannot handle receiving packets
destructors properly.
Now it seems that at least one protocol (CAN) expects to be able
to pass skb->sk through the rx path without getting clobbered.
So this patch attempts to fix this properly by moving the skb_orphan
call to where it's actually needed. In particular, I've added it
to skb_set_owner_[rw] which is what most users of skb->destructor
call.
This is actually an improvement for tun too since it means that
we only give back the amount charged to the socket when the skb
is passed to another socket that will also be charged accordingly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Oliver Hartkopp <olver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support domain-isolation usages, the platform hardware must be
capable of uniquely identifying the requestor (source-id) for each
interrupt message. Without source-id checking for interrupt remapping
, a rouge guest/VM with assigned devices can launch interrupt attacks
to bring down anothe guest/VM or the VMM itself.
This patch adds source-id checking for interrupt remapping, and then
really isolates interrupts for guests/VMs with assigned devices.
Because PCI subsystem is not initialized yet when set up IOAPIC
entries, use read_pci_config_byte to access PCI config space directly.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After the recent changes that went into mm/vmscan.c to overhaul stuff, we
ended up with these warnings on no-mmu systems:
mm/vmscan.c: In function `shrink_page_list':
mm/vmscan.c:580: warning: unused variable `vm_flags'
mm/vmscan.c: In function `shrink_active_list':
mm/vmscan.c:1294: warning: `vm_flags' may be used uninitialized in this function
mm/vmscan.c:1242: note: `vm_flags' was declared here
This is because the no-mmu function defines page_referenced() to work on
the first argument only (the page). It does not clear the vm_flags given
to it because for no-mmu systems, they never actually get utilized. Since
that is no longer strictly true, we need to set vm_flags to 0 like
everyone else so gcc can do proper dead code elimination without annoying
us with unused warnings.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: David McCullough <davidm@snapgear.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a kthread happens to use get_user_pages() on an mm (as KSM does),
there's a chance that it will end up trying to read in a swap page, then
oops in grab_swap_token() because the kthread has no mm: GUP passes down
the right mm, so grab_swap_token() ought to be using it.
We have not identified a stronger case than KSM's daemon (not yet in
mainline), but the issue must have come up before, since RHEL has included
a fix for this for years (though a different fix, they just back out of
grab_swap_token if current->mm is unset: which is what we first proposed,
but using the right mm here seems more correct).
Reported-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There already is a "default-on" trigger but there are problems with it.
For one, it's a inefficient way to do it and requires led trigger support
to be compiled in.
But the real reason is that is produces a glitch on the LED. The GPIO is
allocate with the LED *off*, then *later* when the trigger runs it is
turned back on. If the LED was already on via the GPIO's reset default or
action of the firmware, this produces a glitch where the LED goes from on
to off to on. While normally this is fast enough that it wouldn't be
noticeable to a human observer, there are still serious problems.
One is that there may be something else on the GPIO line, like a hardware
alarm or watchdog, that is fast enough to notice the glitch.
Another is that the kernel may panic before the LED is turned back on, thus
hanging with the LED in the wrong state. This is not just speculation, but
actually happened to me with an embedded system that has an LED which
should turn off when the kernel finishes booting, which was left in the
incorrect state due to a bug in the OF LED binding code.
We also let GPIO LEDs get their initial value from whatever the current
state of the GPIO line is. On some systems the LEDs are put into some
state by the firmware or hardware before Linux boots, and it is desired to
have them keep this state which is otherwise unknown to Linux.
This requires that the underlying GPIO driver support reading the value of
output GPIOs. Some drivers support this and some do not.
The platform device binding gains a field in the platform data
"default_state" that controls this. There are three constants defined to
select from on, off, or keeping the current state. The OpenFirmware
binding uses a property named "default-state" that can be set to "on",
"off", or "keep". The default if the property isn't present is off.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
LEDs driver for National Semiconductor LP3944 Funlight Chip
http://www.national.com/pf/LP/LP3944.html
This helper chip can drive up to 8 leds, with two programmable DIM
modes; it could even be used as a gpio expander but this driver assumes
it is used as a led controller.
The DIM modes are used to set _blink_ patterns for leds, the pattern is
specified supplying two parameters:
- period: from 0s to 1.6s
- duty cycle: percentage of the period the led is on, from 0 to 100
LP3944 can be found on Motorola A910 smartphone, where it drives the rgb
leds, the camera flash light and the displays backlights.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The documentation for the parameters of blink_set() was a bit hard
to find so put some where I'd expected to find it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (38 commits)
fusion: mptsas, fix lock imbalance
[SCSI] scsi_transport_fc: replace BUS_ID_SIZE by fixed count
sd, sr: fix Driver 'sd' needs updating message
scsi_transport_iscsi: return -EOVERFLOW for Too many iscsi targets
fc_transport: Selective return value from BSG timeout function
fc_transport: The softirq_done function registration for BSG request
sym53c8xx: ratelimit parity errors
explain the hidden scsi_wait_scan Kconfig variable
ibmvfc: Fix endless PRLI loop in discovery
ibmvfc: Process async events before command responses
libfc: Add runtime debugging with debug_logging module parameter
libfcoe: Add runtime debugging with module param debug_logging
fcoe: Add runtime debug logging with module parameter debug_logging
scsi_debug: Add support for physical block exponent and alignment
cnic: add NETDEV_1000 and NETDEVICES to Kconfig select
cnic: Fix __symbol_get() build error.
Revert "[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’"
ipr: differentiate pci-x and pci-e based adapters
ipr: add test for MSI interrupt support
scsi_transport_spi: Blacklist Ultrium-3 tape for IU transfers
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: add dummy pgprot_noncached()
lib/checksum.c: fix endianess bug
asm-generic: hook up new system calls
asm-generic: list Arnd as asm-generic maintainer
asm-generic: drop HARDIRQ_BITS definition from hardirq.h
asm-generic: uaccess: fix up local access_ok() usage
asm-generic: uaccess: add missing access_ok() check to strnlen_user()
handle_mm_fault() is now passing fault flags rather than write_access
down to hugetlb_fault(), so better recognize that in hugetlb_fault(),
and in hugetlb_no_page().
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most architectures now provide a pgprot_noncached(), the
remaining ones can simply use an dummy default implementation,
except for cris and xtensa, which should override the
default appropriately.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Magnus Damm <magnus.damm@gmail.com>
Change all the code that deals directly with ICMPv6 type and code
values to use u8 instead of a signed int as that's the actual data
type.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to tracepoints, use an enable variable to reduce
overhead when unused.
Only look for a counter of a particular event type when we know
there is at least one in the system.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Most hardware has limits on minimum and maximum image dimensions and also
requirements about alignment. For example, image width must be even or a
multiple of four. Some hardware has requirements that the total image size
(width * height) be a multiple of some power of two.
v4l_bound_align_image() will enforce min and max width and height, power of
two alignment on width and height, and power of two alignment on total
image size.
It uses an efficient algorithm that will try to find the "closest" image
size that meets the requirements.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new s_config core ops call: this is called with the irq and platform
data to be used to initialize the subdev.
Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls
that allows you to pass these new arguments.
The existing v4l2_i2c_new_subdev functions were modified to also call
s_config.
In the future the existing v4l2_i2c_new_subdev functions will be replaced
by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg
but without the irq and platform_data arguments.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make it very clear that this header should not be used for i2c drivers that
do not need to be compiled for pre-2.6.26 kernels.
As soon as the minimum supported kernel in the v4l-dvb repository becomes
2.6.26 or up, then this header should be removed entirely.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an IR profile for the EVGA inDtube remote control (which is an NEC type
remote)
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: add support for the ov511 bridge
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds autobrightness (so that it can
be turned off to make the already present brightness
control work) and light frequency filtering controls.
The lightfreq control needed 2 different entries
in the ctrls array, as the number of options differs
depending on the sensor. Always one of the 2 entires is
disabled ofcourse.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.infradead.org/~dwmw2/iommu-2.6.31:
intel-iommu: Fix one last ia64 build problem in Pass Through Support
VT-d: support the device IOTLB
VT-d: cleanup iommu_flush_iotlb_psi and flush_unmaps
VT-d: add device IOTLB invalidation support
VT-d: parse ATSR in DMA Remapping Reporting Structure
PCI: handle Virtual Function ATS enabling
PCI: support the ATS capability
intel-iommu: dmar_set_interrupt return error value
intel-iommu: Tidy up iommu->gcmd handling
intel-iommu: Fix tiny theoretical race in write-buffer flush.
intel-iommu: Clean up handling of "caching mode" vs. IOTLB flushing.
intel-iommu: Clean up handling of "caching mode" vs. context flushing.
VT-d: fix invalid domain id for KVM context flush
Fix !CONFIG_DMAR build failure introduced by Intel IOMMU Pass Through Support
Intel IOMMU Pass Through Support
Fix up trivial conflicts in drivers/pci/{intel-iommu.c,intr_remapping.c}
The purpose of this patch is to improve the remote mount path lookup
support for distributed filesystems such as the NFSv4 client.
When given a mount command of the form "mount server:/foo/bar /mnt", the
NFSv4 client is required to look up the filehandle for "server:/", and
then look up each component of the remote mount path "foo/bar" in order
to find the directory that is actually going to be mounted on /mnt.
Following that remote mount path may involve following symlinks,
crossing server-side mount points and even following referrals to
filesystem volumes on other servers.
Since the standard VFS path lookup code already supports walking paths
that contain all these features (using in-kernel automounts for
following referrals) we would like to be able to reuse that rather than
duplicate the full path traversal functionality in the NFSv4 client code.
This patch therefore defines a VFS helper function create_mnt_ns(), that
sets up a temporary filesystem namespace and attaches a root filesystem to
it. It exports the create_mnt_ns() and put_mnt_ns() function for use by
filesystem modules.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to allow modules to use it without having to export vfsmount_lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLAB uses get/put_online_cpus() which use a mutex which is itself only
initialized when cpu_hotplug_init() is called. Currently we hang suring
boot in SLAB due to doing that too late.
Reported by James Bottomley and Sachin Sant (and possibly others).
Debugged by Benjamin Herrenschmidt.
This just removes the dynamic initialization of the data structures, and
replaces it with a static one, avoiding this dependency entirely, and
removing one unnecessary special initcall.
Tested-by: Sachin Sant <sachinp@in.ibm.com>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.infradead.org/mtd-2.6: (63 commits)
mtd: OneNAND: Allow setting of boundary information when built as module
jffs2: leaking jffs2_summary in function jffs2_scan_medium
mtd: nand: Fix memory leak on txx9ndfmc probe failure.
mtd: orion_nand: use burst reads with double word accesses
mtd/nand: s3c6400 support for s3c2410 driver
[MTD] [NAND] S3C2410: Use DIV_ROUND_UP
[MTD] [NAND] S3C2410: Deal with unaligned lengths in S3C2440 buffer read/write
[MTD] [NAND] S3C2410: Allow the machine code to get the BBT table from NAND
[MTD] [NAND] S3C2410: Added a kerneldoc for s3c2410_nand_set
mtd: physmap_of: Add multiple regions and concatenation support
mtd: nand: max_retries off by one in mxc_nand
mtd: nand: s3c2410_nand_setrate(): use correct macros for 2412/2440
mtd: onenand: add bbt_wait & unlock_all as replaceable for some platform
mtd: Flex-OneNAND support
mtd: nand: add OMAP2/OMAP3 NAND driver
mtd: maps: Blackfin async: fix memory leaks in probe/remove funcs
mtd: uclinux: mark local stuff static
mtd: uclinux: do not allow to be built as a module
mtd: uclinux: allow systems to override map addr/size
mtd: blackfin NFC: fix hang when using NAND on BF527-EZKITs
...
Some filesystems need to set lockdep map for i_mutex differently for
different directories. For example OCFS2 has system directories (for
orphan inode tracking and for gathering all system files like journal
or quota files into a single place) which have different locking
locking rules than standard directories. For a filesystem setting
lockdep map is naturaly done when the inode is read but we have to
modify unlock_new_inode() not to overwrite the lockdep map the filesystem
has set.
Acked-by: peterz@infradead.org
CC: mingo@redhat.com
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
In asm-generic/vmlinux.lds.h, name INIT_RAM_FS consistently, no matter the
setting of CONFIG_BLK_DEV_INITRD. This corrects:
commit ef53dae865
Author: Sam Ravnborg <sam@ravnborg.org>
Date: Sun Jun 7 20:46:37 2009 +0200
Subject: Improve vmlinux.lds.h support for arch specific linker scripts
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.31' of git://fieldses.org/git/linux-nfsd: (60 commits)
SUNRPC: Fix the TCP server's send buffer accounting
nfsd41: Backchannel: minorversion support for the back channel
nfsd41: Backchannel: cleanup nfs4.0 callback encode routines
nfsd41: Remove ip address collision detection case
nfsd: optimise the starting of zero threads when none are running.
nfsd: don't take nfsd_mutex twice when setting number of threads.
nfsd41: sanity check client drc maxreqs
nfsd41: move channel attributes from nfsd4_session to a nfsd4_channel_attr struct
NFS: kill off complicated macro 'PROC'
sunrpc: potential memory leak in function rdma_read_xdr
nfsd: minor nfsd_vfs_write cleanup
nfsd: Pull write-gathering code out of nfsd_vfs_write
nfsd: track last inode only in use_wgather case
sunrpc: align cache_clean work's timer
nfsd: Use write gathering only with NFSv2
NFSv4: kill off complicated macro 'PROC'
NFSv4: do exact check about attribute specified
knfsd: remove unreported filehandle stats counters
knfsd: fix reply cache memory corruption
knfsd: reply cache cleanups
...
* 'for-2.6.31' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (128 commits)
nfs41: sunrpc: xprt_alloc_bc_request() should not use spin_lock_bh()
nfs41: Move initialization of nfs4_opendata seq_res to nfs4_init_opendata_res
nfs: remove unnecessary NFS_INO_INVALID_ACL checks
NFS: More "sloppy" parsing problems
NFS: Invalid mount option values should always fail, even with "sloppy"
NFS: Remove unused XDR decoder functions
NFS: Update MNT and MNT3 reply decoding functions
NFS: add XDR decoder for mountd version 3 auth-flavor lists
NFS: add new file handle decoders to in-kernel mountd client
NFS: Add separate mountd status code decoders for each mountd version
NFS: remove unused function in fs/nfs/mount_clnt.c
NFS: Use xdr_stream-based XDR encoder for MNT's dirpath argument
NFS: Clean up MNT program definitions
lockd: Don't bother with RPC ping for NSM upcalls
lockd: Update NSM state from SM_MON replies
NFS: Fix false error return from nfs_callback_up() if ipv6.ko is not available
NFS: Return error code from nfs_callback_up() to user space
NFS: Do not display the setting of the "intr" mount option
NFS: add support for splice writes
nfs41: Backchannel: CB_SEQUENCE validation
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (43 commits)
via-velocity: Fix velocity driver unmapping incorrect size.
mlx4_en: Remove redundant refill code on RX
mlx4_en: Removed redundant check on lso header size
mlx4_en: Cancel port_up check in transmit function
mlx4_en: using stop/start_all_queues
mlx4_en: Removed redundant skb->len check
mlx4_en: Counting all the dropped packets on the TX side
usbnet cdc_subset: fix issues talking to PXA gadgets
Net: qla3xxx, remove sleeping in atomic
ipv4: fix NULL pointer + success return in route lookup path
isdn: clean up documentation index
cfg80211: validate station settings
cfg80211: allow setting station parameters in mesh
cfg80211: allow adding/deleting stations on mesh
ath5k: fix beacon_int handling
MAINTAINERS: Fix Atheros pattern paths
ath9k: restore PS mode, before we put the chip into FULL SLEEP state.
ath9k: wait for beacon frame along with CAB
acer-wmi: fix rfkill conversion
ath5k: avoid PCI FATAL interrupts by restoring RETRY_TIMEOUT disabling
...
Add the wakeup enable register to the list of OMAP-specific UART
registers. This is to support forthcoming OMAP PM enhancements which
use the wakeup feature of the OMAP's 8250-based UART.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds core functions for request-based dm.
When struct mapped device (md) is initialized, md->queue has
an I/O scheduler and the following functions are used for
request-based dm as the queue functions:
make_request_fn: dm_make_request()
pref_fn: dm_prep_fn()
request_fn: dm_request_fn()
softirq_done_fn: dm_softirq_done()
lld_busy_fn: dm_lld_busy()
Actual initializations are done in another patch (PATCH 2).
Below is a brief summary of how request-based dm behaves, including:
- making request from bio
- cloning, mapping and dispatching request
- completing request and bio
- suspending md
- resuming md
bio to request
==============
md->queue->make_request_fn() (dm_make_request()) calls __make_request()
for a bio submitted to the md.
Then, the bio is kept in the queue as a new request or merged into
another request in the queue if possible.
Cloning and Mapping
===================
Cloning and mapping are done in md->queue->request_fn() (dm_request_fn()),
when requests are dispatched after they are sorted by the I/O scheduler.
dm_request_fn() checks busy state of underlying devices using
target's busy() function and stops dispatching requests to keep them
on the dm device's queue if busy.
It helps better I/O merging, since no merge is done for a request
once it is dispatched to underlying devices.
Actual cloning and mapping are done in dm_prep_fn() and map_request()
called from dm_request_fn().
dm_prep_fn() clones not only request but also bios of the request
so that dm can hold bio completion in error cases and prevent
the bio submitter from noticing the error.
(See the "Completion" section below for details.)
After the cloning, the clone is mapped by target's map_rq() function
and inserted to underlying device's queue using
blk_insert_cloned_request().
Completion
==========
Request completion can be hooked by rq->end_io(), but then, all bios
in the request will have been completed even error cases, and the bio
submitter will have noticed the error.
To prevent the bio completion in error cases, request-based dm clones
both bio and request and hooks both bio->bi_end_io() and rq->end_io():
bio->bi_end_io(): end_clone_bio()
rq->end_io(): end_clone_request()
Summary of the request completion flow is below:
blk_end_request() for a clone request
=> blk_update_request()
=> bio->bi_end_io() == end_clone_bio() for each clone bio
=> Free the clone bio
=> Success: Complete the original bio (blk_update_request())
Error: Don't complete the original bio
=> blk_finish_request()
=> rq->end_io() == end_clone_request()
=> blk_complete_request()
=> dm_softirq_done()
=> Free the clone request
=> Success: Complete the original request (blk_end_request())
Error: Requeue the original request
end_clone_bio() completes the original request on the size of
the original bio in successful cases.
Even if all bios in the original request are completed by that
completion, the original request must not be completed yet to keep
the ordering of request completion for the stacking.
So end_clone_bio() uses blk_update_request() instead of
blk_end_request().
In error cases, end_clone_bio() doesn't complete the original bio.
It just frees the cloned bio and gives over the error handling to
end_clone_request().
end_clone_request(), which is called with queue lock held, completes
the clone request and the original request in a softirq context
(dm_softirq_done()), which has no queue lock, to avoid a deadlock
issue on submission of another request during the completion:
- The submitted request may be mapped to the same device
- Request submission requires queue lock, but the queue lock
has been held by itself and it doesn't know that
The clone request has no clone bio when dm_softirq_done() is called.
So target drivers can't resubmit it again even error cases.
Instead, they can ask dm core for requeueing and remapping
the original request in that cases.
suspend
=======
Request-based dm uses stopping md->queue as suspend of the md.
For noflush suspend, just stops md->queue.
For flush suspend, inserts a marker request to the tail of md->queue.
And dispatches all requests in md->queue until the marker comes to
the front of md->queue. Then, stops dispatching request and waits
for the all dispatched requests to complete.
After that, completes the marker request, stops md->queue and
wake up the waiter on the suspend queue, md->wait.
resume
======
Starts md->queue.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch contains a device-mapper mirror log module that forwards
requests to userspace for processing.
The structures used for communication between kernel and userspace are
located in include/linux/dm-log-userspace.h. Due to the frequency,
diversity, and 2-way communication nature of the exchanges between
kernel and userspace, 'connector' was chosen as the interface for
communication.
The first log implementations written in userspace - "clustered-disk"
and "clustered-core" - support clustered shared storage. A userspace
daemon (in the LVM2 source code repository) uses openAIS/corosync to
process requests in an ordered fashion with the rest of the nodes in the
cluster so as to prevent log state corruption. Other implementations
with no association to LVM or openAIS/corosync, are certainly possible.
(Imagine if two machines are writing to the same region of a mirror.
They would both mark the region dirty, but you need a cluster-aware
entity that can handle properly marking the region clean when they are
done. Otherwise, you might clear the region when the first machine is
done, not the second.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Currently, device-mapper maintains a separate instance of 'struct
queue_limits' for each table of each device. When the configuration of
a device is to be changed, first its table is loaded and this structure
is populated, then the device is 'resumed' and the calculated
queue_limits are applied.
This places restrictions on how userspace may process related devices,
where it is often advantageous to 'load' tables for several devices
at once before 'resuming' them together. As the new queue_limits
only take effect after the 'resume', if they are changing and one
device uses another, the latter must be 'resumed' before the former
may be 'loaded'.
This patch moves the calculation of these queue_limits out of
the 'load' operation into 'resume'. Since we are no longer
pre-calculating this struct, we no longer need to maintain copies
within our dm structs.
dm_set_device_limits() now passes the 'start' of the device's
data area (aka pe_start) as the 'offset' to blk_stack_limits().
init_valid_queue_limits() is replaced by blk_set_default_limits().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: martin.petersen@oracle.com
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add .iterate_devices to 'struct target_type' to allow a function to be
called for all devices in a DM target. Implemented it for all targets
except those in dm-snap.c (origin and snapshot).
(The raid1 version number jumps to 1.12 because we originally reserved
1.1 to 1.11 for 'block_on_error' but ended up using 'handle_errors'
instead.)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: martin.petersen@oracle.com
Use blk_stack_limits() to stack block limits (including topology) rather
than duplicate the equivalent within Device Mapper.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add support for passing a 32 bit "cookie" into the kernel with the
DM_SUSPEND, DM_DEV_RENAME and DM_DEV_REMOVE ioctls. The (unsigned)
value of this cookie is returned to userspace alongside the uevents
issued by these ioctls in the variable DM_COOKIE.
This means the userspace process issuing these ioctls can be notified
by udev after udev has completed any actions triggered.
To minimise the interface extension, we pass the cookie into the
kernel in the event_nr field which is otherwise unused when calling
these ioctls. Incrementing the version number allows userspace to
determine in advance whether or not the kernel supports the cookie.
If the kernel does support this but userspace does not, there should
be no impact as the new variable will just get ignored.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce num_flush_requests for a target to set to say how many flush
instructions (empty barriers) it wants to receive. These are sent by
__clone_and_map_empty_barrier with map_info->flush_request going from 0
to (num_flush_requests - 1).
Old targets without flush support won't receive any flush requests.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault(). All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a SCSI ULD driver sets blk_queue_prep_rq(), it should clean it
up itself on remove(), and not from the bus callbacks. This
removes the need to hook into bus->remove(), which should not
be used at the same time as driver->remove().
[jejb: fix sdkp initialisation problem due to mismerge]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch adds the /sys/module/libfc/parameters/debug_logging
file to sysfs as a module parameter. It accepts an integer
bitmask for logging. Currently it supports:
bit
LSB 0 = general libfc debugging
1 = lport debugging
2 = disc debugging
3 = rport debugging
4 = fcp debugging
5 = EM debugging
6 = exch/seq debugging
7 = scsi logging (mostly error handling)
the other bits are not used at this time.
The patch converts all of the libfc source files to use
these new macros and removes the old FC_DBG macro.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
If we are sending or receiving data for the task successfully do
not run the scsi eh, because we know the task is making progress.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq, irq.h: Fix kernel-doc warnings
genirq: fix comment to say IRQ_WAKE_THREAD
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (49 commits)
perfcounter: Handle some IO return values
perf_counter: Push perf_sample_data through the swcounter code
perf_counter tools: Define and use our own u64, s64 etc. definitions
perf_counter: Close race in perf_lock_task_context()
perf_counter, x86: Improve interactions with fast-gup
perf_counter: Simplify and fix task migration counting
perf_counter tools: Add a data file header
perf_counter: Update userspace callchain sampling uses
perf_counter: Make callchain samples extensible
perf report: Filter to parent set by default
perf_counter tools: Handle lost events
perf_counter: Add event overlow handling
fs: Provide empty .set_page_dirty() aop for anon inodes
perf_counter: tools: Makefile tweaks for 64-bit powerpc
perf_counter: powerpc: Add processor back-end for MPC7450 family
perf_counter: powerpc: Make powerpc perf_counter code safe for 32-bit kernels
perf_counter: powerpc: Change how processor-specific back-ends get selected
perf_counter: powerpc: Use unsigned long for register and constraint values
perf_counter: powerpc: Enable use of software counters on 32-bit powerpc
perf_counter tools: Add and use isprint()
...
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
tracing/urgent: warn in case of ftrace_start_up inbalance
tracing/urgent: fix unbalanced ftrace_start_up
function-graph: add stack frame test
function-graph: disable when both x86_32 and optimize for size are configured
ring-buffer: have benchmark test print to trace buffer
ring-buffer: do not grab locks in nmi
ring-buffer: add locks around rb_per_cpu_empty
ring-buffer: check for less than two in size allocation
ring-buffer: remove useless compile check for buffer_page size
ring-buffer: remove useless warn on check
ring-buffer: use BUF_PAGE_HDR_SIZE in calculating index
tracing: update sample event documentation
tracing/filters: fix race between filter setting and module unload
tracing/filters: free filter_string in destroy_preds()
ring-buffer: use commit counters for commit pointer accounting
ring-buffer: remove unused variable
ring-buffer: have benchmark test handle discarded events
ring-buffer: prevent adding write in discarded area
tracing/filters: strloc should be unsigned short
tracing/filters: operand can be negative
...
Fix up kmemcheck-induced conflict in kernel/trace/ring_buffer.c manually
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: add driver for Synaptics I2C touchpad
Input: synaptics - add support for reporting x/y resolution
Input: ALPS - handle touchpoints buttons correctly
Input: gpio-keys - change timer to workqueue
Input: ads7846 - pin change interrupt support
Input: add support for touchscreen on W90P910 ARM platform
Input: appletouch - improve finger detection
Input: wacom - clear Intuos4 wheel data when finger leaves proximity
Input: ucb1400 - move static function from header into core
Input: add driver for EETI touchpanels
Input: ads7846 - more detailed model name in sysfs
Input: ads7846 - support swapping x and y axes
Input: ati_remote2 - use non-atomic bitops
Input: introduce lm8323 keypad driver
Input: psmouse - ESD workaround fix for OLPC XO touchpad
Input: tsc2007 - make sure platform provides get_pendown_state()
Input: uinput - flush all pending ff effects before destroying device
Input: simplify name handling for certain input handles
Input: serio - do not use deprecated dev.power.power_state
Input: wacom - add support for Intuos4 tablets
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (24 commits)
agp/intel: Make intel_i965_mask_memory use dma_addr_t for physical addresses
agp: add user mapping support to ATI AGP bridge.
drm/i915: enable GEM on PAE.
drm/radeon: fix unused variables warning
agp: switch AGP to use page array instead of unsigned long array
agpgart: detected ALi M???? chipset with M1621
drm/radeon: command stream checker for r3xx-r5xx hardware
drm/radeon: Fully initialize LVDS info also when we can't get it from the ROM.
radeon: Fix CP byte order on big endian architectures with KMS.
agp/uninorth: Handle user memory types.
drm/ttm: Add some powerpc cache flush code.
radeon: Enable modesetting on non-x86.
drm/radeon: Respect AGP cant_use_aperture flag.
drm: EDID endianness fixes.
drm/radeon: this VRAM vs aperture test is wrong, just remove it.
drm/ttm: fix an error path to exit function correctly
drm: Apply "Memory fragmentation from lost alignment blocks"
ttm: Return -ERESTART when a signal interrupts bo eviction.
drm: Remove memory debugging infrastructure.
drm/i915: Clear fence register on tiling stride change.
...
Synaptics uses anisotropic coordinate system. On some wide touchpads
vertical resolution can be twice as high as horizontal which causes
unequal sensitivity on x/y directions. Add support for reading the
resolution with EVIOCGABS ioctl.
Signed-off-by: Tero Saarni <tero.saarni@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
arch_acpi_processor_cleanup_pdc() in x86 and ia64 results in memory allocated
for _PDC objects that is never freed and will cause memory leak in case of
physical CPU remove and add. Patch fixes the memory leak by freeing the
objects soon after _PDC is evaluated.
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: New macro to initialize i2c address lists on the fly
i2c: Don't advertise i2c functions when not available
i2c: Use rwsem instead of mutex for board info
i2c: Add a sysfs interface to instantiate devices
i2c: Limit core locking to the necessary sections
i2c: Kill the redundant client list
i2c: Kill is_newstyle_driver
i2c: Merge i2c_attach_client into i2c_new_device
i2c: Drop i2c_probe function
i2c: Get rid of the legacy binding model
i2c: Kill client_register and client_unregister methods
dma_sync_single() and dma_sync_sg() have been described as "Backwards
compat, remove in 2.7.x" for a long time (since 2.6.5).
This marks dma_sync_single() and dma_sync_sg() as deprecated so the users
get notified before removing them.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark them deprecated so that out-of-tree developers get notified about
this before their modules break when these macros are removed.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Yang Hongyang <yanghy@cn.fujitsu.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the ARM PrimeCell PL061 GPIO AMBA peripheral. The
driver is implemented using the gpiolib framework.
This driver also includes support for the use of the PL061 as an interrupt
controller (secondary).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This information allows userspace to implement a hybrid policy where
it can store the rfkill soft-blocked state in platform non-volatile
storage if available, and if not then file-based storage can be used.
Some users prefer platform non-volatile storage because of the behaviour
when dual-booting multiple versions of Linux, or if the rfkill setting
is changed in the BIOS setting screens, or if the BIOS responds to
wireless-toggle hotkeys itself before the relevant platform driver has
been loaded.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The setting of the "persistent" flag is also made more explicit using
a new rfkill_init_sw_state() function, instead of special-casing
rfkill_set_sw_state() when it is called before registration.
Suspend is a bit of a corner case so we try to get away without adding
another hack to rfkill-input - it's going to be removed soon.
If the state does change over suspend, users will simply have to prod
rfkill-input twice in order to toggle the state.
Userspace policy agents will be able to implement a more consistent user
experience. For example, they can avoid the above problem if they
toggle devices individually. Then there would be no "global state"
to get out of sync.
Currently there are only two rfkill drivers with persistent soft-blocked
state. thinkpad-acpi already checks the software state on resume.
eeepc-laptop will require modification.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
CC: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For video4linux we sometimes need to probe for a single i2c address.
Normally you would do it like this:
static const unsigned short addrs[] = {
addr, I2C_CLIENT_END
};
client = i2c_new_probed_device(adapter, &info, addrs);
This is a bit awkward and I came up with this macro:
#define V4L2_I2C_ADDRS(addr, addrs...) \
((const unsigned short []){ addr, ## addrs, I2C_CLIENT_END })
This can construct a list of one or more i2c addresses on the fly. But
this is something that really belongs in i2c.h, renamed to I2C_ADDRS.
With this macro we can just do:
client = i2c_new_probed_device(adapter, &info, I2C_ADDRS(addr));
Note that this can also be used to initialize an array:
static const unsigned short addrs[] = I2C_ADDRS(0x2a, 0x2c);
Whether you want to is another matter, but it works. This functionality is
also available in the oldest supported gcc (3.2).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Surround i2c function declarations with ifdefs, so that they aren't
advertised when i2c-core isn't actually built. That way, drivers using
these functions unconditionally will result in an immediate build
failure, rather than a late linking failure which is harder to figure
out.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Add a sysfs interface to instantiate and delete I2C devices. This is
primarily a replacement of the force_* module parameters implemented
by some i2c drivers. These module parameters were implemented
internally by the I2C_CLIENT_INSMOD* macros, which don't scale well.
This can also be used when developing a driver on a self-soldered
board which doesn't yet have proper I2C device declaration at the
platform level, and presumably for various debugging situations.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
We used to maintain our own per-adapter list of i2c clients, but this
is redundant with what the driver core does, and no longer needed.
Just drop the redundant list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Legacy i2c drivers are gone, all drivers are new-style now, so there
is no point to check.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The legacy i2c_probe() function has no users left, get rid of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
We converted all the legacy i2c drivers so we can finally get rid of
the legacy binding model. Hooray!
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
These methods were useful in the legacy binding model but no longer in
the new (standard) binding model. There are no users left so we can
drop them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
sys_rt_tgsigqueueinfo and sys_perf_counter_open
have been added in 2.6.31, so hook them up in the
generic unistd.h file.
Since the file is now in the mainline kernel, we
are no longer reordering the numbers but just add
system calls at the end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Architechtures normally don't need to set a HARDIRQ_BITS
unless they have hardcoded a specific value in assembly.
This drops the definition from asm-generic/hardirq.h, which
results in linux/hardirq.h setting its default of 10.
Both the old default of 8 and the linux/hardirq.h default
of 10 are sufficient because they only limit the number
of nested hardirqs, and we normally run out of stack space
much earlier than exceeding 256 or even 1024 nested interrupts.
Reported-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's no reason that I can see to use the short __access_ok() form
directly when the access_ok() is clearer in intent and for most people,
expands to the same C code (i.e. always specify the first field -- access
type). Not all no-mmu systems lack memory protection, so the read/write
could feasibly be checked.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The strnlen_user() function was missing a access_ok() check on the pointer
given. We've had cases on Blackfin systems where test programs caused
kernel crashes here because userspace passed up a NULL/-1 pointer and the
kernel gladly attempted to run strlen() on it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The task migrations counter was causing rare and hard to decypher
memory corruptions under load. After a day of debugging and bisection
we found that the problem was introduced with:
3f731ca: perf_counter: Fix cpu migration counter
Turning them off fixes the crashes. Incidentally, the whole
perf_counter_task_migration() logic can be done simpler as well,
by injecting a proper sw-counter event.
This cleanup also fixed the crashes. The precise failure mode is
not completely clear yet, but we are clearly not unhappy about
having a fix ;-)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before exposing upstream tools to a callchain-samples ABI, tidy it
up to make it more extensible in the future:
Use markers in the IP chain to denote context, use (u64)-1..-4095 range
for these context markers because we use them for ERR_PTR(), so these
addresses are unlikely to be mapped.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the iucv message limit for a communication path is exceeded,
sendmsg() returns -EAGAIN instead of -EPIPE.
The calling application can then handle this error situtation,
e.g. to try again after waiting some time.
For blocking sockets, sendmsg() waits up to the socket timeout
before returning -EAGAIN. For the new wait condition, a macro
has been introduced and the iucv_sock_wait_state() has been
refactored to this macro.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up to "block: enable by default support for large devices
and files on 32-bit archs".
Rename CONFIG_LBD to CONFIG_LBDAF to:
- allow update of existing [def]configs for "default y" change
- reflect that it is used also for large files support nowadays
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Prepare to share backchannel code with NFSv4.1.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Ricardo Labiaga <Ricardo.Labiaga@netapp.com>
[nfsd41: use nfsd4_cb_sequence for callback minorversion]
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
This switches AGP to use an array of pages for tracking the
pages allocated to the GART. This should enable GEM on PAE to work
a lot better as we can pass highmem pages to the PAT code and it will
do the right thing with them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
also for the atomic path by using a common code-path.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case gcc does something funny with the stack frames, or the return
from function code, we would like to detect that.
An arch may implement passing of a variable that is unique to the
function and can be saved on entering a function and can be tested
when exiting the function. Usually the frame pointer can be used for
this purpose.
This patch also implements this for x86. Where it passes in the stack
frame of the parent function, and will test that frame on exit.
There was a case in x86_32 with optimize for size (-Os) where, for a
few functions, gcc would align the stack frame and place a copy of the
return address into it. The function graph tracer modified the copy and
not the actual return address. On return from the funtion, it did not go
to the tracer hook, but returned to the parent. This broke the function
graph tracer, because the return of the parent (where gcc did not do
this funky manipulation) returned to the location that the child function
was suppose to. This caused strange kernel crashes.
This test detected the problem and pointed out where the issue was.
This modifies the parameters of one of the functions that the arch
specific code calls, so it includes changes to arch code to accommodate
the new prototype.
Note, I notice that the parsic arch implements its own push_return_trace.
This is now a generic function and the ftrace_push_return_trace should be
used instead. This patch does not touch that code.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
jbd2: clean up jbd2_journal_try_to_free_buffers()
ext4: Don't update ctime for non-extent-mapped inodes
ext4: Fix up whitespace issues in fs/ext4/inode.c
ext4: Fix 64-bit block type problem on 32-bit platforms
ext4: teach the inode allocator to use a goal inode number
ext4: Use a hash of the topdir directory name for the Orlov parent group
ext4: document the "abort" mount option
ext4: move the abort flag from s_mount_opts to s_mount_flags
ext4: update the s_last_mounted field in the superblock
ext4: change s_mount_opt to be an unsigned int
ext4: online defrag -- Add EXT4_IOC_MOVE_EXT ioctl
ext4: avoid unnecessary spinlock in critical POSIX ACL path
ext3: avoid unnecessary spinlock in critical POSIX ACL path
ext4: convert instrumentation from markers to tracepoints
jbd2: convert instrumentation from markers to tracepoints
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
The page allocator also needs the masking of gfp flags during boot,
so this moves it out of slab/slub and uses it with the page allocator
as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://neil.brown.name/md: (39 commits)
md/raid5: correctly update sync_completed when we reach max_resync
md/raid5: add missing call to schedule() after prepare_to_wait()
md/linear: use call_rcu to free obsolete 'conf' structures.
md linear: Protecting mddev with rcu locks to avoid races
md: Move check for bitmap presence to personality code.
md: remove chunksize rounding from common code.
md: raid0/linear: ensure device sizes are rounded to chunk size.
md: move assignment of ->utime so that it never gets skipped.
md: Push down reconstruction log message to personality code.
md: merge reconfig and check_reshape methods.
md: remove unnecessary arguments from ->reconfig method.
md: raid5: check stripe cache is large enough in start_reshape
md: raid0: chunk_sectors cleanups.
md: fix some comments.
md/raid5: Use is_power_of_2() in raid5_reconfig()/raid6_reconfig().
md: convert conf->chunk_size and conf->prev_chunk to sectors.
md: Convert mddev->new_chunk to sectors.
md: Make mddev->chunk_size sector-based.
md: raid0 :Enables chunk size other than powers of 2.
md: prepare for non-power-of-two chunk sizes
...
This patch adds lib/gcd.c which contains a greatest common divider
implementation taken from sound/core/pcm_timer.c
Several usages of this new library function will be sent to subsystem
maintainers.
[akpm@linux-foundation.org: use swap() (pointed out by Joe)]
[akpm@linux-foundation.org: just add gcd.o to obj-y, remove Kconfig changes]
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Simon Horman <horms@verge.net.au>
Cc: Julius Volz <juliusv@google.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the kernel side of the PPS support currently named
"LinuxPPS".
PPS means "pulse per second" and a PPS source is just a device which
provides a high precision signal each second so that an application can
use it to adjust system clock time.
Common use is the combination of the NTPD as userland program with a GPS
receiver as PPS source to obtain a wallclock-time with sub-millisecond
synchronisation to UTC.
To obtain this goal the userland programs shoud use the PPS API
specification (RFC 2783 - Pulse-Per-Second API for UNIX-like Operating
Systems, Version 1.0) which in part is implemented by this patch. It
provides a set of chars devices, one per PPS source, which can be used to
get the time signal. The RFC's functions can be implemented by accessing
to these char devices.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg KH <greg@kroah.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On embedded devices, sleep mode conditions can be tricky to handle,
Especially when processors tend to pull-down the w1 bus during sleep. Bus
slaves (such as the ds2760) may interpret this as a reason for power-down
conditions and entirely switch off the device.
This patch adds a callback function pointer to let users switch on and off
the external pull-up resistor. This lets the outside world know whether
the processor is currently actively driving the bus or not.
When this callback is not provided, the code behaviour won't change.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Ville Syrjala <syrjala@sci.fi>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We unified x86 and IA64's handling of multiple dma mapping operations
(struct dma_map_ops in linux/dma-mapping.h) so we can remove duplication
in their arch/include/asm/dma-mapping.h.
This patchset adds include/asm-generic/dma-mapping-common.h that provides
some generic dma mapping function definitions for the users of struct
dma_map_ops. This enables us to remove about 100 lines. This also
enables us to easily add CONFIG_DMA_API_DEBUG support, which only x86
supports for now. The 4th patch adds CONFIG_DMA_API_DEBUG support to IA64
by adding only 8 lines.
This patch:
This header file provides some mapping function definitions that the users
of struct dma_map_ops can use.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable the use of GCC's coverage testing tool gcov [1] with the Linux
kernel. gcov may be useful for:
* debugging (has this code been reached at all?)
* test improvement (how do I change my test to cover these lines?)
* minimizing kernel configurations (do I need this option if the
associated code is never run?)
The profiling patch incorporates the following changes:
* change kbuild to include profiling flags
* provide functions needed by profiling code
* present profiling data as files in debugfs
Note that on some architectures, enabling gcc's profiling option
"-fprofile-arcs" for the entire kernel may trigger compile/link/
run-time problems, some of which are caused by toolchain bugs and
others which require adjustment of architecture code.
For this reason profiling the entire kernel is initially restricted
to those architectures for which it is known to work without changes.
This restriction can be lifted once an architecture has been tested
and found compatible with gcc's profiling. Profiling of single files
or directories is still available on all platforms (see config help
text).
[1] http://gcc.gnu.org/onlinedocs/gcc/Gcov.html
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
seq_write() can be used to construct seq_files containing arbitrary data.
Required by the gcov-profiling interface to synthesize binary profiling
data files.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call constructors (gcc-generated initcall-like functions) during kernel
start and module load. Constructors are e.g. used for gcov data
initialization.
Disable constructor support for usermode Linux to prevent conflicts with
host glibc.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Function is really private to ipc/ and avoid struct kern_ipc_perm
forward declaration.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
find_task_by_pid_type_ns is only used to implement find_task_by_vpid and
find_task_by_pid_ns, but both of them pass PIDTYPE_PID as first argument.
So just fold find_task_by_pid_type_ns into find_task_by_pid_ns and use
find_task_by_pid_ns to implement find_task_by_vpid.
While we're at it also remove the exports for find_task_by_pid_ns and
find_task_by_vpid - we don't have any modular callers left as the only
modular caller of he old pre pid namespace find_task_by_pid (gfs2) was
switched to pid_task which operates on a struct pid pointer instead of a
pid_t. Given the confusion about pid_t values vs namespace that's
generally the better option anyway and I think we're better of restricting
modules to do it that way.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use rcu_read_lock() instead of tasklist_lock to find/get the task
in ptrace_get_task_struct().
- Make it static, it has no callers outside of ptrace.c.
- The comment doesn't match the reality, this helper does not do
any checks. Beacuse it is really trivial and static I removed the
whole comment.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tracehook_unsafe_exec() doesn't need task_lock(), remove the old comment.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't have an interface to reset mem.limit or memsw.limit now.
This patch allows to reset mem.limit or memsw.limit when they are being
set to -1.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes mis-accounting of swap usage in memcg.
In the current implementation, memcg's swap account is uncharged only when
swap is completely freed. But there are several cases where swap cannot
be freed cleanly. For handling that, this patch changes that memcg
uncharges swap account when swap has no references other than cache.
By this, memcg's swap entry accounting can be fully synchronous with the
application's behavior.
This patch also changes memcg's hooks for swap-out.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Balbir Singh <balbir@in.ibm.com>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mem_cgroup_cache_charge_swapin() isn't used any more, so remove no-op
definition of it in header file.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add file RSS tracking per memory cgroup
We currently don't track file RSS, the RSS we report is actually anon RSS.
All the file mapped pages, come in through the page cache and get
accounted there. This patch adds support for accounting file RSS pages.
It should
1. Help improve the metrics reported by the memory resource controller
2. Will form the basis for a future shared memory accounting heuristic
that has been proposed by Kamezawa.
Unfortunately, we cannot rename the existing "rss" keyword used in
memory.stat to "anon_rss". We however, add "mapped_file" data and hope to
educate the end user through documentation.
[hugh.dickins@tiscali.co.uk: fix mem_cgroup_update_mapped_file_stat oops]
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Li Zefan <lizf@cn.fujitsu.cn>
Cc: Paul Menage <menage@google.com>
Cc: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several code paths in reiserfs have a construct like:
if (is_direntry_le_ih(ih = B_N_PITEM_HEAD(src, item_num))) ...
which, in addition to being ugly, end up causing compiler warnings with
gcc 4.4.0. Previous compilers didn't issue a warning.
fs/reiserfs/do_balan.c:1273: warning: operation on `aux_ih' may be undefined
fs/reiserfs/lbalance.c:393: warning: operation on `ih' may be undefined
fs/reiserfs/lbalance.c:421: warning: operation on `ih' may be undefined
fs/reiserfs/lbalance.c:777: warning: operation on `ih' may be undefined
I believe this is due to the ih being passed to macros which evaluate the
argument more than once. This is old code and we haven't seen any
problems with it, but this patch eliminates the warnings.
It converts the multiple evaluation macros to static inlines and does a
preassignment for the cases that were causing the warnings because that
code is just ugly.
Reported-by: Chris Mason <mason@oracle.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to the PCA953x driver to use the GPIOLIB naming facility for
GPIOs.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mpc52xx_psc_spi driver is the last user of the legacy activate_cs and
deactivate_cs callbacks, so convert the driver to the cs_control hook and
remove the legacy callbacks from fsl_spi_platform_data struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move some common spi_setup() error checks into the SPI framework from the
spi_master controller drivers:
- Add a new "mode_bits" field to spi_master
- Use that in spi_setup to validate the spi->mode value being
requested. Setting this new field is now mandatory for any
controller supporting more than vanilla SPI_MODE_0.
- Update all spi_master drivers to:
* Initialize that field
* Remove current spi_setup() checks using that value.
This is a net minor code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start moving some spi_setup() functionality into the SPI core from the
various spi_master controller drivers:
- Make that function stop being an inline;
- Move two common idioms from drivers into that new function:
* Default bits_per_word to 8 if that field isn't set
* Issue a standardized dev_dbg() message
This is a net minor source code shrink, and supports enhancments found in
some follow-up patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Statistics for softirq doesn't exist.
It will be helpful like statistics for interrupts.
This patch introduces counting the number of softirq,
which will be exported in /proc/softirqs.
When softirq handler consumes much CPU time,
/proc/stat is like the following.
$ while :; do cat /proc/stat | head -n1 ; sleep 10 ; done
cpu 88 0 408 739665 583 28 2 0 0
cpu 450 0 1090 740970 594 28 1294 0 0
^^^^
softirq
In such a situation,
/proc/softirqs shows us which softirq handler is invoked.
We can see the increase rate of softirqs.
<before>
$ cat /proc/softirqs
CPU0 CPU1 CPU2 CPU3
HI 0 0 0 0
TIMER 462850 462805 462782 462718
NET_TX 0 0 0 365
NET_RX 2472 2 2 40
BLOCK 0 0 381 1164
TASKLET 0 0 0 224
SCHED 462654 462689 462698 462427
RCU 3046 2423 3367 3173
<after>
$ cat /proc/softirqs
CPU0 CPU1 CPU2 CPU3
HI 0 0 0 0
TIMER 463361 465077 465056 464991
NET_TX 53 0 1 365
NET_RX 3757 2 2 40
BLOCK 0 0 398 1170
TASKLET 0 0 0 224
SCHED 463074 464318 464612 463330
RCU 3505 2948 3947 3673
When CPU TIME of softirq is high,
the rates of increase is the following.
TIMER : 220/sec : CPU1-3
NET_TX : 5/sec : CPU0
NET_RX : 120/sec : CPU0
SCHED : 40-200/sec : all CPU
RCU : 45-58/sec : all CPU
The rates of increase in an idle mode is the following.
TIMER : 250/sec
SCHED : 250/sec
RCU : 2/sec
It seems many softirqs for receiving packets and rcu are invoked. This
gives us help for checking system.
Signed-off-by: Keika Kobayashi <kobayashi.kk@ncos.nec.co.jp>
Reviewed-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It hasn't been used in ages, and having the user tell your how much
memory is being freed at free time is a recipe for disaster even if it
was ever used.
Signed-off-by: Eric Anholt <eric@anholt.net>
Alternative method of mmap() data output handling that provides
better overflow management and a more reliable data stream.
Unlike the previous method, that didn't have any user->kernel
feedback and relied on userspace keeping up, this method relies on
userspace writing its last read position into the control page.
It will ensure new output doesn't overwrite not-yet read events,
new events for which there is no space left are lost and the
overflow counter is incremented, providing exact event loss
numbers.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Add boundary checks for call-chain events. In case of corrupted
entries we could crash otherwise.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
System notify events (0x00-0x7f) are common across all device types
and should be handled in Linux/ACPI, not in drivers. However, some
BIOSes use system notify events in device-specific ways that require
the driver to be involved.
This patch adds a ACPI_DRIVER_ALL_NOTIFY_EVENTS driver flag. When a
driver sets this flag and supplies a .notify method, Linux/ACPI calls
the .notify method for ALL notify events on the device, not just the
device-specific (0x80-0xff) events.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_get_pci_dev() is (hopefully) better, and all callers have been
converted, so let's get rid of this duplicated functionality.
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_get_pci_dev() is better, and all callers have been converted, so
eliminate acpi_get_pci_id().
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There is no need to pass a segment/bus tuple to this API, as the callsite
always has a struct pci_bus. We can derive segment/bus from the
struct pci_bus, so let's take this opportunit to simplify the API and
make life easier for the callers.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
A PCI domain cannot change as you descend down subordinate buses, which
makes the 'segment' argument to acpi_pci_irq_add_prt() useless.
Change the interface to take a struct pci_bus *, from whence we can derive
the bus number and segment. Reducing the number of arguments makes life
simpler for callers.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that we can dynamically convert an ACPI CA handle to a
struct pci_dev at runtime, there's no need to statically bind
them during boot.
acpi_pci_bind/unbind are vastly simplified, and are only used
to evaluate _PRT methods on P2P bridges and non-bridge children.
This patch also changes the time-space tradeoff ever so slightly.
Looking up the ACPI-PCI binding is never in the performance path, and by
eliminating this caching, we save 24 bytes for each _ADR device in the
ACPI namespace.
This patch lays further groundwork to eventually eliminate
the acpi_driver_ops.bind callback.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Convert an ACPI CA handle to a struct pci_dev.
Performing this lookup dynamically allows us to get rid of the
ACPI-PCI binding code, which:
- eliminates struct acpi_device vs struct pci_dev lifetime issues
- lays more groundwork for eliminating .start from acpi_device_ops
and thus simplifying ACPI drivers
- whacks out a lot of code
This change lays the groundwork for eliminating much of pci_bind.c.
Although pci_root.c may not be the most logical place for this
change, putting it here saves us from having to export acpi_pci_find_root.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Returns whether an ACPI CA node is a PCI root bridge or not.
This API is generically useful, and shouldn't just be a hotplug function.
The implementation becomes much simpler as well.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_pci_root_add() explicitly assigns device->ops.bind, and later
calls acpi_pci_bind_root(), which also does the same thing.
We don't need to repeat ourselves; removing the explicit assignment
allows us to make acpi_pci_bind() static.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Clean up: Relocate MNT program procedure number definitions to the
only file that uses them. Relocate the version number definitions,
which are shared, to nfs.h. Remove duplicate program number
definitions.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When rpc.statd starts up in user space at boot time, it attempts to
write the latest NSM local state number into
/proc/sys/fs/nfs/nsm_local_state.
If lockd.ko isn't loaded yet (as is the case in most configurations),
that file doesn't exist, thus the kernel's NSM state remains set to
its initial value of zero during lockd operation.
This is a problem because rpc.statd and lockd use the NSM state number
to prevent repeated lock recovery on rebooted hosts. If lockd sends
a zero NSM state, but then a delayed SM_NOTIFY with a real NSM state
number is received, there is no way for lockd or rpc.statd to
distinguish that stale SM_NOTIFY from an actual reboot. Thus lock
recovery could be performed after the rebooted host has already
started reclaiming locks, and those locks will be lost.
We could change /etc/init.d/nfslock so it always modprobes lockd.ko
before starting rpc.statd. However, if lockd.ko is ever unloaded
and reloaded, we are back at square one, since the NSM state is not
preserved across an unload/reload cycle. This may happen frequently
on clients that use automounter. A period of NFS inactivity causes
lockd.ko to be unloaded, and the kernel loses its NSM state setting.
Instead, let's use the fact that rpc.statd plants the local system's
NSM state in every SM_MON (and SM_UNMON) reply. lockd performs a
synchronous SM_MON upcall to the local rpc.statd _before_ sending its
first NLM request to a new remote. This would permit rpc.statd to
provide the current NSM state to lockd, even after lockd.ko had been
unloaded and reloaded.
Note that NLMPROC_LOCK arguments are constructed before the
nsm_monitor() call, so we have to rearrange argument construction very
slightly to make this all work out.
And, the kernel appears to treat NSM state as a u32 (see struct
nlm_args and nsm_res). Make nsm_local_state a u32 as well, to ensure
we don't get bogus comparison results.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
1/ Raid5 has learned to take over also raid4 and raid6 arrays.
2/ new_chunk in mdp_superblock_1 is in sectors, not bytes.
Signed-off-by: NeilBrown <neilb@suse.de>
Defines a new 'struct nfs4_slot_table' in the 'struct nfs4_session'
for use by the backchannel. Initializes, resets, and destroys the backchannel
slot table in the same manner the forechannel slot table is initialized,
reset, and destroyed.
The sequenceid for each slot in the backchannel slot table is initialized
to 0, whereas the forechannel slotid's sequenceid is set to 1.
Signed-off-by: Ricardo Labiaga <Ricardo.Labiaga@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
The 'rq_received' member of 'struct rpc_rqst' is used to track when we
have received a reply to our request. With v4.1, the backchannel
can now accept callback requests over the existing connection. Rename
this field to make it clear that it is only used for tracking reply bytes
and not all bytes received on the connection.
Signed-off-by: Ricardo Labiaga <Ricardo.Labiaga@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
This svc_xprt is passed on to the callback service thread to be later used
to processes incoming svc_rqst's
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Linus Torvalds
Krzysztof Helt
David Brownell
KAMEZAWA Hiroyuki
Michael Buesch
Tejun Heo
Heiko Carstens
Davide Libenzi
John Muir
Miklos Szeredi
Paul Mackerras
David S. Miller
Bartlomiej Zolnierkiewicz
Alexey Zaytsev
Jeremy Kerr
Jan Engelhardt
Jaswinder Singh Rajput
Patrick McHardy
Eric Miao
Mimi Zohar
Marcelo Tosatti
Tim Abbott
Paul Mundt
Kurt Garloff
Peter Zijlstra
Peter Zijlstra
Stefan Richter
Rémi Denis-Courmont
Al Viro
Markus Trippelsdorf
Ankit Jain
Michel Dänzer
Len Brown
Eric Paris
Zhao Yakui
Herbert Xu
Weidong Han
Mike Frysinger
Hugh Dickins
Richard Purdie
Trent Piepho
Antonio Ospite
Mark Brown
Brian Haley
Hans Verkuil
Devin Heitmueller
Hans de Goede
Trond Myklebust
Jan Kara
David Howells
Robert Love
Kevin Hilman
Kiyoshi Ueda
Jonthan Brassow
Mike Snitzer
Milan Broz
Mikulas Patocka
Hannes Reinecke
Robert Love
Mike Christie
Tero Saarni
Pallipadi, Venkatesh
FUJITA Tomonori
Jiri Slaby
Baruch Siach
Alan Jenkins
Jean Delvare
Arnd Bergmann
Hendrik Brueckner
Andy Adamson
Dave Airlie
Michel Dänzer
Thomas Hellstrom
Steven Rostedt
Benjamin Herrenschmidt
Florian Fainelli
Rodolfo Giometti
Daniel Mack
Peter Oberparleiter
Alexey Dobriyan
Christoph Hellwig
Oleg Nesterov
Daisuke Nishimura
Li Zefan
Balbir Singh
Jeff Mahoney
Daniel Silverstone
Anton Vorontsov
Keika Kobayashi
Eric Anholt
Jiri Pirko
Ingo Molnar
Bjorn Helgaas
Alexander Chiang
Chuck Lever
Andre Noll
Ricardo Labiaga