The problem occurring is a hw-race where there's an outstanding read-flash
operation occurring while the chip is being reset (done via an sg_reset script).
After the chip is paused, the read-flash operation never completes and the
DPC thread, while trying to complete the reset, is never able to recover,
as the HW appears to be hung...
The fix is to wait for outstanding flash operation prior to doing a sg_reset -h.
And to wait for reset to complete before any flash operations.
Note, during the wait, if any of the operation (reset/flash) does not complete,
failure is returned to the upper layer. The upper layer either need to
fail or retry.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently we can only issue the task management (TM)
commands via the mailbox mechanism. This is a limitation,
since only one mailbox command can be issued at a time.
The purpose of this effort is to provide support for
issuing and processing the respose to TM and Marker
IOCBs asynchronously. Towards achieving this, the
consolidated srb architecture that is currently used for
BSG and IOCB/Logio commands has been enhanced and used.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, BSG and IOCB/Logio commands have a different
framework (srb structs). The purpose of this effort is to
consolidate them into a generalized framework for these
as well as other asynchronous operations in the future.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver should not be unloaded if any application is using it.
To disallow driver unload, driver use count must be incremented.
Application uses this char device as handle and increases driver
use count to avoid possible driver unload.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently error status is cleared only after the uncorrectable fatal errors
in the qla2xxx_pci_slot_reset. This fix is added to clear the error status in
qla2xxx_pci_resume. This way for both fatal and non-fatal errors the error
status gets cleared properly.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=572258
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enhanced the driver to support new FCoE host bus adapter.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The default is enabled since 7e47e5ca18.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla1280: retain firmware for error recovery
[SCSI] attirbute_container: Initialize sysfs attributes with sysfs_attr_init
[SCSI] advansys: fix regression with request_firmware change
[SCSI] qla2xxx: Updated version number to 8.03.02-k2.
[SCSI] qla2xxx: Prevent sending mbx commands from sysfs during isp reset.
[SCSI] qla2xxx: Disable MSI on qla24xx chips other than QLA2432.
[SCSI] qla2xxx: Check to make sure multique and CPU affinity support is not enabled at the same time.
[SCSI] qla2xxx: Correct vp_idx checking during PORT_UPDATE processing.
[SCSI] qla2xxx: Honour "Extended BB credits" bit for CNAs.
[SCSI] scsi_transport_fc: Make sure commands are completed when rport is offline
[SCSI] libiscsi: Fix recovery slowdown regression
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The logic is changed to detect this condition based on following
1) both module parameters are off (ql2xmaxqueues and ql2xmultique_tag).
2) both module parameters are on (ql2xmaxqueues and ql2xmultique_tag).
3) The HBA does not support multi queue.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Can be used to balance NIC/FCoE traffic distribution.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The explicit logout (LOGO) issued at the end of the callback will
flush (via normal scsi_cmnd->done()) any outstanding commands
(FCP2) the firmware is holding. While iterating through the
outstanding_cmnd array in qla2x00_abort_fcport_cmds(), locking
and unlocking of the hardware spinlock, opens-up the driver to
cases where the processed SRB (sp) could be used after the
command completed from interrupt context.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Target-level resets are unlikely to complete if done after the
bus (LIP/OLS/NOS) has been reset. Perform target-level resets,
if necessary, prior to hitting the bus.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix for BSG request cleanup when the request timesout.
Proper release of driver resources used for BSG request during timeout cleanup.
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Firmware is loaded from flash for these ISP types.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
qla2xxx: EEH added call to pci_restore_state.
qla2xxx: EEH added delay in slot reset routine.
qla2xxx: EEH moved call to pci_save_state(), see (1).
qla2xxx: EEH additional changes for RHEL5.5.
qla2xxx: EEH added function call, removed function call, see (2).
(1) In qla2xxx_probe_one the call to pci_save_state() has been
moved to after the call to qla2xxx_request_irqs().
(2) Add call to pci_disable_pcie_error_reporting() in remove_one.
Delete call to pci_cleanup_aer_uncorrect_error_status() in pci_resume.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The driver did not account for non-tape devices needing to employ
proper FCP2 recovery. Driver now checks the FCP2-capable flag
only, rather than using a midlayer-determined flag (TYPE_TAPE).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added fundamental reset and pci save state.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed the module parameters ql2xqfulltracking and ql2xqfullrampup
since the queue depth ramp up/down functionality is moved to scsi-ml.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix crash in qla2x00_fdmi_register() due to the dpc
thread executing before the scsi host has been fully
added.
Unable to handle kernel NULL pointer dereference (address 00000000000001d0)
qla2xxx_7_dpc[4140]: Oops 8813272891392 [1]
Call Trace:
[<a000000100016910>] show_stack+0x50/0xa0
sp=e00000b07c59f930 bsp=e00000b07c591400
[<a000000100017180>] show_regs+0x820/0x860
sp=e00000b07c59fb00 bsp=e00000b07c5913a0
[<a00000010003bd60>] die+0x1a0/0x2e0
sp=e00000b07c59fb00 bsp=e00000b07c591360
[<a0000001000681a0>] ia64_do_page_fault+0x8c0/0x9e0
sp=e00000b07c59fb00 bsp=e00000b07c591310
[<a00000010000c8e0>] ia64_native_leave_kernel+0x0/0x270
sp=e00000b07c59fb90 bsp=e00000b07c591310
[<a000000207197350>] qla2x00_fdmi_register+0x850/0xbe0 [qla2xxx]
sp=e00000b07c59fd60 bsp=e00000b07c591290
[<a000000207171570>] qla2x00_configure_loop+0x1930/0x34c0 [qla2xxx]
sp=e00000b07c59fd60 bsp=e00000b07c591128
[<a0000002071732b0>] qla2x00_loop_resync+0x1b0/0x2e0 [qla2xxx]
sp=e00000b07c59fdf0 bsp=e00000b07c5910c0
[<a000000207166d40>] qla2x00_do_dpc+0x9a0/0xce0 [qla2xxx]
sp=e00000b07c59fdf0 bsp=e00000b07c590fa0
[<a0000001000d5bb0>] kthread+0x110/0x140
sp=e00000b07c59fe00 bsp=e00000b07c590f68
[<a000000100014a30>] kernel_thread_helper+0xd0/0x100
sp=e00000b07c59fe30 bsp=e00000b07c590f40
[<a00000010000a4c0>] start_kernel_thread+0x20/0x40
sp=e00000b07c59fe30 bsp=e00000b07c590f40
crash> dis a000000207197350
0xa000000207197350 <qla2x00_fdmi_register+2128>: [MMI] ld1 r45=[r14];;
crash> scsi_qla_host.host 0xe00000b058c73ff8
host = 0xe00000b058c73be0,
crash> Scsi_Host.shost_data 0xe00000b058c73be0
shost_data = 0x0, <<<<<<<<<<<
The fc_transport fc_* workqueue threads have yet to be created.
crash> ps | grep _7
3891 2 2 e00000b075c80000 IN 0.0 0 0 [scsi_eh_7]
4140 2 3 e00000b07c590000 RU 0.0 0 0 [qla2xxx_7_dpc]
The thread creating adding the Scsi_Host is blocked due to other
activity in sysfs.
crash> bt 3762
PID: 3762 TASK: e00000b071e70000 CPU: 3 COMMAND: "modprobe"
#0 [BSP:e00000b071e71548] schedule at a000000100727e00
#1 [BSP:e00000b071e714c8] __mutex_lock_slowpath at a0000001007295a0
#2 [BSP:e00000b071e714a8] mutex_lock at a000000100729830
#3 [BSP:e00000b071e71478] sysfs_addrm_start at a0000001002584f0
#4 [BSP:e00000b071e71440] create_dir at a000000100259350
#5 [BSP:e00000b071e71410] sysfs_create_subdir at a000000100259510
#6 [BSP:e00000b071e713b0] internal_create_group at a00000010025c880
#7 [BSP:e00000b071e71388] sysfs_create_group at a00000010025cc50
#8 [BSP:e00000b071e71368] dpm_sysfs_add at a000000100425050
#9 [BSP:e00000b071e71310] device_add at a000000100417d90
#10 [BSP:e00000b071e712d8] scsi_add_host at a00000010045a380
#11 [BSP:e00000b071e71268] qla2x00_probe_one at a0000002071be950
#12 [BSP:e00000b071e71248] local_pci_probe at a00000010032e490
#13 [BSP:e00000b071e71218] pci_device_probe at a00000010032ecd0
#14 [BSP:e00000b071e711d8] driver_probe_device at a00000010041d480
#15 [BSP:e00000b071e711a8] __driver_attach at a00000010041d6e0
#16 [BSP:e00000b071e71170] bus_for_each_dev at a00000010041c240
#17 [BSP:e00000b071e71150] driver_attach at a00000010041d0a0
#18 [BSP:e00000b071e71108] bus_add_driver at a00000010041b080
#19 [BSP:e00000b071e710c0] driver_register at a00000010041dea0
#20 [BSP:e00000b071e71088] __pci_register_driver at a00000010032f610
#21 [BSP:e00000b071e71058] (unknown) at a000000207200270
#22 [BSP:e00000b071e71018] do_one_initcall at a00000010000a9c0
#23 [BSP:e00000b071e70f98] sys_init_module at a0000001000fef00
#24 [BSP:e00000b071e70f98] ia64_ret_from_syscall at a00000010000c740
So, it appears that qla2xxx dpc thread is moving forward before the
scsi host has been completely added.
This patch moves the setting of the init_done (and online) flag to
after the call to scsi_add_host() to hold off the dpc thread.
Found via large lun count testing using 2.6.31.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the duplicated code from FC LLDs to SCSI FC transport class.
Acked-by: James Smart <james.smart@emulex.com>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Acked-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code would inadvertently skip the deferred
fc_remote_port_delete() call for rports hanging off any vport.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code would break-out of loop after only one iteration.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In fabric-login based on iop BIT_8 firmware notifies presence of
a FCP2 device and not necessarily a TAPE device. So instead of
setting FCF_TAPE_PRESENT flag there we set it using
scsi_device->type after mid-layer scan recognises "type" of the
device.
It also adds a new flag FCF_FCP2_DEVICE for any future use.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ISPs which support this feature include 23xx and above.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Lay groundwork for adding alternative asynchronous operations by
generalize and extending the SRB structure. This allows for
follow-on patches to add support for:
- Asynchronous logins.
- ELS/CT passthru requests.
- Loopback requests.
- Non-blocking mailbox commands (ABTS, Task Management, etc).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the multiqueue mode fails to work, the driver falls back on single
queue mode. This ensures that the firmware is reinitialized with single
queue options and all the resources are readjusted accordingly.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Queued work processing will now be serialized with its own
lower-priority spinlock. This also simplifies the work-queue
interface for future work-queue consumers.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In case the onboard firmware is unable to be read or loaded for
operation, attempt to fallback to a limited-operational firmware
image stored in a different flash region. This will allow a user
to reflash and correct a board with proper operational firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware currently provides PB and PGF TLVs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As it may be useful during debugging to use a specific firmware
image.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.
The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth. If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth. While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.
This patch implements an "off switch" as a module parameter.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
