LIBFC depends upon SCSI_FC_ATTRS and select's CRC32C.
The only alternative would be to 'select' CRC32C and all of
SCSI_FC_ATTRS direct and indirect dependencies in the Kconfig section
for every LIBFCOE user which makes little sense.
Subsequently, use 'depends' instead of 'select' for LIBFCOE too.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on a problem and solution from Maurizio Lombardi
where bnx2fc isn't consistent in which device struct we using for DMA
map and unmap operations. Make them consistent by using dma_sg_unmap
in bnx2fc_unmap_sg_list like bnx2fc_map_sg.
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Just like CNIC, tristate of these two modules is also dependent on IPV6.
These need to be handled separately as they select CNIC, which can override
tristate for CNIC from 'm' to 'y', which can cause build failures when ipv6 is
compiled as a module even if CNIC's Kconfig will only 'm' or 'n' when ipv6 is
compiled as a module.
Fixes: c99d667e85 ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QLogic has acquired the NetXtremeII products and drivers from Broadcom.
This patch re-brands bnx2fc driver as a QLogic driver
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Recently had this warning reported:
[ 290.489047] Call Trace:
[ 290.489053] [<ffffffff8169efec>] dump_stack+0x19/0x1b
[ 290.489055] [<ffffffff810ac7a9>] __might_sleep+0x179/0x230
[ 290.489057] [<ffffffff816a4ad5>] mutex_lock_nested+0x55/0x520
[ 290.489061] [<ffffffffa01b9905>] ? bnx2fc_l2_rcv_thread+0xc5/0x4c0 [bnx2fc]
[ 290.489065] [<ffffffffa0174c1a>] fc_vport_id_lookup+0x3a/0xa0 [libfc]
[ 290.489068] [<ffffffffa01b9a6c>] bnx2fc_l2_rcv_thread+0x22c/0x4c0 [bnx2fc]
[ 290.489070] [<ffffffffa01b9840>] ? bnx2fc_vport_destroy+0x110/0x110 [bnx2fc]
[ 290.489073] [<ffffffff8109e0cd>] kthread+0xed/0x100
[ 290.489075] [<ffffffff8109dfe0>] ? insert_kthread_work+0x80/0x80
[ 290.489077] [<ffffffff816b2fec>] ret_from_fork+0x7c/0xb0
[ 290.489078] [<ffffffff8109dfe0>] ? insert_kthread_work+0x80/0x80
Its due to the fact that we call a potentially sleeping function from the bnx2fc
rcv path with preemption disabled (via the get_cpu call embedded in the per-cpu
variable stats lookup in bnx2fc_l2_rcv_thread.
Easy enough fix, we can just move the stats collection later in the function
where we are sure we won't preempt or sleep. This also allows us to not have to
enable pre-emption when doing a per-cpu lookup, since we're certain not to get
rescheduled.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In case of of error, the bnx2fc_cmd_mgr_alloc() function will call
the bnx2fc_cmd_mgr_free() to perform the cleanup.
The problem is that in one case the latter may try to scan
some not-yet initialized lists, resulting in a kernel panic.
This patch prevents this from happening by freeing the lists
before calling bnx2fc_cmd_mgr_free().
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch consists of the usual driver updates (qla2xxx, qla4xxx, lpfc,
be2iscsi, fnic, ufs, NCR5380) The NCR5380 is the addition to maintained status
of a long neglected driver for older hardware. In addition there are a lot of
minor fixes and cleanups and some more updates to make scsi mq ready.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTlcwiAAoJEDeqqVYsXL0M5qsIALzVPLd4yxA16zCiaPQUeIV5
mfYmwISFlN+qW3AcUeSH4D13YgegCjEBfqaDMWvIkgouxLy/7jpxtChutq3MCzUE
cDT1B9+ZrzoqBISRNHEh/gx5F1MOF2VPuqG2pe0J90wyRCNzJscB6PbtWMAo86CA
2eu7wq3K9FXxCC1qY0PzwBLXHqUcgk5GWiK9CM/k4W0NiTVeNmwPeh5i91IQnBHx
E2l7NAXgNLyCf5tyeswvZ4pW0T3hlaswNmBB4qC8oJm4U6UqMN+tk4ML63Pz7uPe
4mlHG0uI8Vbdi13iv1EDUZ9Vo8iqVrzP2UAhakgP9poKSGqE4d/MD0EKNGQB2Es=
=cBY8
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch consists of the usual driver updates (qla2xxx, qla4xxx,
lpfc, be2iscsi, fnic, ufs, NCR5380) The NCR5380 is the addition to
maintained status of a long neglected driver for older hardware. In
addition there are a lot of minor fixes and cleanups and some more
updates to make scsi mq ready"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (130 commits)
include/scsi/osd_protocol.h: remove unnecessary __constant
mvsas: Recognise device/subsystem 9485/9485 as 88SE9485
Revert "be2iscsi: Fix processing cqe for cxn whose endpoint is freed"
mptfusion: fix msgContext in mptctl_hp_hostinfo
acornscsi: remove linked command support
scsi/NCR5380: dprintk macro
fusion: Remove use of DEF_SCSI_QCMD
fusion: Add free msg frames to the head, not tail of list
mpt2sas: Add free smids to the head, not tail of list
mpt2sas: Remove use of DEF_SCSI_QCMD
mpt2sas: Remove uses of serial_number
mpt3sas: Remove use of DEF_SCSI_QCMD
mpt3sas: Remove uses of serial_number
qla2xxx: Use kmemdup instead of kmalloc + memcpy
qla4xxx: Use kmemdup instead of kmalloc + memcpy
qla2xxx: fix incorrect debug printk
be2iscsi: Bump the driver version
be2iscsi: Fix processing cqe for cxn whose endpoint is freed
be2iscsi: Fix destroy MCC-CQ before MCC-EQ is destroyed
be2iscsi: Fix memory corruption in MBX path
...
In case of error, the bnx2fc_allocate_hash_table() didn't free
all the memory it allocated.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If bnx2fc_allocate_hash_table() for some reasons fails, it is possible that the
hash_tbl_segments or the hash_tbl_pbl pointers are NULL.
In this case bnx2fc_free_hash_table() will panic the system.
this patch also fixes a memory leak, the hash_tbl_segments pointer was never
freed.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
hash_table_size is not used by the bnx2fc_free_hash_table() function.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
This patch consists of the usual driver updates (megaraid_sas, scsi_debug,
qla2xxx, qla4xxx, lpfc, bnx2fc, be2iscsi, hpsa, ipr) plus an assortment of
minor fixes and the first precursors of SCSI-MQ (the code path
simplifications) and the bug fix for the USB oops on remove (which involves an
infrastructure change, so is sent via the main tree with a delayed backport
after a cycle in which it is shown to introduce no new bugs).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTOsP1AAoJEDeqqVYsXL0MraUIAMCHWIN791cSc/E4d6mw/6nC
j5CG/wwuw3VfqJcJJ8PcItfReWPuS7aLwhAx3wNGDUe7Vcz9pmcgJU9c2/ZWhIJH
D0YXnGSkkfxI9Wc5WJ/NbueS0TFt0G5B6wpIxSLpSEJ1k9I90vxe3symCwv5vS/p
3Cd2nZZCLg6ArzZJ3PJLnNG9FUp2ZBeZwfPu4CuPm+3kEq9oRATg7bS4NNtVTQLP
0zNs5rKAVWfnE5Ii8VFjA7DLduG9W1IBNnSI7EERenrLKMbHG5530Rnl71uvjjgY
0jmQ5YGpTsYcJggLdaijZdK+zuq6Jtc+0DwWJKIE3cEHx3kUrYi4UQWTTRk9ttQ=
=Bp1Y
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This patch consists of the usual driver updates (megaraid_sas,
scsi_debug, qla2xxx, qla4xxx, lpfc, bnx2fc, be2iscsi, hpsa, ipr) plus
an assortment of minor fixes and the first precursors of SCSI-MQ (the
code path simplifications) and the bug fix for the USB oops on remove
(which involves an infrastructure change, so is sent via the main tree
with a delayed backport after a cycle in which it is shown to
introduce no new bugs)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (196 commits)
[SCSI] sd: Quiesce mode sense error messages
[SCSI] add support for per-host cmd pools
[SCSI] simplify command allocation and freeing a bit
[SCSI] megaraid: simplify internal command handling
[SCSI] ses: Use vpd information from scsi_device
[SCSI] Add EVPD page 0x83 and 0x80 to sysfs
[SCSI] Return VPD page length in scsi_vpd_inquiry()
[SCSI] scsi_sysfs: Implement 'is_visible' callback
[SCSI] hpsa: update driver version to 3.4.4-1
[SCSI] hpsa: fix bad endif placement in RAID 5 mapper code
[SCSI] qla2xxx: Fix build errors related to invalid print fields on some architectures.
[SCSI] bfa: Replace large udelay() with mdelay()
[SCSI] vmw_pvscsi: Some improvements in pvscsi driver.
[SCSI] vmw_pvscsi: Add support for I/O requests coalescing.
[SCSI] vmw_pvscsi: Fix pvscsi_abort() function.
[SCSI] remove deprecated IRQF_DISABLED from SCSI
[SCSI] bfa: Updating Maintainers email ids
[SCSI] ipr: Add new CCIN definition for Grand Canyon support
[SCSI] ipr: Format HCAM overlay ID 0x21
[SCSI] ipr: Use pci_enable_msi_range() and pci_enable_msix_range()
...
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the bnx2fc code in scsi by using this latter form of callback
registration.
Cc: Eddie Wai <eddie.wai@broadcom.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The bnx2/bnx2x rings are made up of linked pages. However there is an
upper limit on the page size as some the page size settings are 16-bit
in the hardware/firmware interface. In the current code, some parts
use BNX2_PAGE_SIZE which has a 16K upper limit and some parts use
PAGE_SIZE. On archs with >= 64K PAGE_SIZE, it generates some compile
warnings. Define a new CNIC_PAGE_SZIE which has an upper limit of
16K and use it consistently in all relevant parts.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCSI retry delay upon SAM_STAT_BUSY/_SET_FULL was not being handled
in bnx2fc. This patch adds such handling by returning TARGET_BUSY
to the SCSI ML for the corresponding LUN until the retry timer expires.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The problem has been identified to be a change in the scsi_remove_device
path where a call to the pm_runtime_set_memalloc_noio was added when
del_gendisk is called in this path. Note that the new pm routine
attempts to cycle through all parent devices from the FC target device
to set the memalloc_noio flag. Because of this new change, a dependency
was created between the FC target device and the parent netdev device
in the destroy path.
In order to synchronized the destroy paths, bnx2fc has been modified
to flush all destroy workqueues in the NETDEV_UNREGISTER return path.
[ 4.123584] BUG: soft lockup - CPU#8 stuck for 22s! [kworker/8:3:8082]
[ 4.123713] Call Trace:
[ 4.123719] [<ffffffff815dfbe0>] klist_next+0x20/0xf0
[ 4.123725] [<ffffffff813e9220>] ? pm_save_wakeup_count+0x70/0x70
[ 4.123731] [<ffffffff813d9e4e>] device_for_each_child+0x4e/0x70
[ 4.123735] [<ffffffff813e9554>] pm_runtime_set_memalloc_noio+0x94/0xf0
[ 4.123740] [<ffffffff812d4d74>] del_gendisk+0x264/0x2a0
[ 4.123747] [<ffffffffa00c6dc9>] sd_remove+0x69/0xb0 [sd_mod]
[ 4.123751] [<ffffffff813de24f>] __device_release_driver+0x7f/0xf0
[ 4.123754] [<ffffffff813de2e3>] device_release_driver+0x23/0x30
[ 4.123757] [<ffffffff813ddab4>] bus_remove_device+0xf4/0x170
[ 4.123760] [<ffffffff813da475>] device_del+0x135/0x1d0
[ 4.123765] [<ffffffff81411b75>] __scsi_remove_device+0xc5/0xd0
[ 4.123768] [<ffffffff81411ba6>] scsi_remove_device+0x26/0x40
[ 4.123770] [<ffffffff81411d40>] scsi_remove_target+0x160/0x210
[ 4.123775] [<ffffffffa0420e4c>] fc_rport_final_delete+0xac/0x1f0 [scsi_transport_fc]
[ 4.123780] [<ffffffff810774ab>] process_one_work+0x17b/0x460
[ 4.123783] [<ffffffff8107825b>] worker_thread+0x11b/0x400
[ 4.123786] [<ffffffff81078140>] ? rescuer_thread+0x3e0/0x3e0
[ 4.123791] [<ffffffff8107e9c0>] kthread+0xc0/0xd0
[ 4.123794] [<ffffffff8107e900>] ? kthread_create_on_node+0x110/0x110
[ 4.123798] [<ffffffff8160ceec>] ret_from_fork+0x7c/0xb0
[ 4.123801] [<ffffffff8107e900>] ? kthread_create_on_node+0x110/0x110
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the case when a SCSI_CMD times out, bnx2fc will initiate the sending of the
ABTS. However, if the SCSI layer's SCSI command timer also times out, it'll
instantiate a task abort of the same xid.
The race condition this patch tries to fix is as follows:
SCSI_CMD timeout (20s)
thread 1 thread 2
send ABTS
rx ABTS cmpl
task abort_eh
explicit LOGO since ABTS was engaged
CLEANUP cmpl
SCSI_CMD cmpl (ABTS cmpl)
instantiate RRQ
wait 10s
attempt to send RRQ (because of LOGO, it wouldn't continue)
Note that there is no call to scsi_done for this SCSI_CMD cmpletion
in this path.
The patch changes the path of execution to call scsi_done immediately
instead of instantiating the RRQ.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Preliminary to removing compare_ether_addr altogether:
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
fnic doesn't use any of the create/destroy/enable/disable interfaces
either from the (legacy) module paramaters or the (new) fcoe_sysfs
interfaces. When fcoe_sysfs was introduced fnic wasn't changed since
it wasn't using the interfaces. libfcoe incorrectly assumed that that
all of its users were using fcoe_sysfs and when adding and deleting
FCFs would assume the existance of a fcoe_ctlr_device. fnic was not
allocating this structure because it doesn't care about the standard
user interfaces (fnic starts on link only). If/When libfcoe tried to use
the fcoe_ctlr_device's lock for the first time a NULL pointer exception
would be triggered.
Since fnic doesn't care about sysfs or user interfaces, the solution
is to drop libfcoe's assumption that all drivers are using fcoe_sysfs.
This patch accomplishes this by changing some of the structure
relationships.
We need a way to determine when a LLD is using fcoe_sysfs or not and
we can do that by checking for the existance of the fcoe_ctlr_device.
Prior to this patch, it was assumed that the fcoe_ctlr structure was
allocated with the fcoe_ctlr_device and immediately followed it in
memory. To reach the fcoe_ctlr_device we would simply go back in memory
from the fcoe_ctlr to get the fcoe_ctlr_device.
Since fnic doesn't allocate the fcoe_ctlr_device, we cannot keep that
assumption. This patch adds a pointer from the fcoe_ctlr to the
fcoe_ctlr_device. For bnx2fc and fcoe we will continue to allocate the
two structures together, but then we'll set the ctlr->cdev pointer
to point at the fcoe_ctlr_device. fnic will not change and will continue
to allocate the fcoe_ctlr itself, and ctlr->cdev will remain NULL.
When libfcoe adds fcoe_fcf's to the fcoe_ctlr it will check if ctlr->cdev
is set and only if so will it continue to interact with fcoe_sysfs.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Hiral Patel <hiralpat@cisco.com>
commit b9871bcfd2
bnx2x: VF RSS support - PF side
changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc. For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IO is successfully completed while an abort is pending, eh_abort
incorrectly assumes that abort failed and performes recovery by issuing
cleanup. Howerver, cleanup timesout as the firmware has no clue about
this IO. Fix this by checking if the IO has already completed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set perf_config to 3 during firmware initialization to enable both
cached connections as well as cached tasks.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The firmware supports a maximum of 4K FCoE exchanges. In 4-port devices,
or when working in multi-function mode, this resource needs to be distributed
between the various possible FCoE functions.
This information needs to be calculated by bnx2x and propagated into bnx2fc
via cnic. bnx2fc can then use this value to calculate corresponding xid
resources instead of using global constants.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split discovery initialization in code that is setup once (fcoe_disc_init)
and code that can be re-configured (fcoe_disc_config).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Currently libfcoe is doing some libfc discovery layer initialization outside of
libfc. This patch moves this code into libfc and sets up a split in discovery
(one time) initialization code and (re-configurable) settings that will come in
the next patch.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
The fcoemon userspace daemon is searching for the a hostX
under the the /sys/bus/fcoe/devices/ctlrX/ entries. When
interfaces created using fcoe_sysfs and fcoe.ko this linkage
is setup correctly, but bnx2fc is not doing the same thing
and therefore fcoemon does not create the fcoe interface
for bnx2fc.
This patch sets up the correct linkage for bnx2fc such that
fcoemon will work correctly with fcoe_sysfs and bnx2fc.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Delete successive tests to the same location. The code tested the result
of a previous allocation, that itself was already tested. It is changed to
test the result of the most recent allocation.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Increase max_sectors from 512 to 1024 in order to support max IO size of 512KB.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since the FW counters are 32-bit, accumulate the stats in the driver.
[jejb: fix checkpatch warning]
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We used to map doorbell register after FW enable request is complete.
This causes a race condition when unsolicited event is received, and FW
sends a CQE for it. Since the doorbell is not mapped, driver does not
arm CQ, which means FW will not notify the driver for further CQ
completions. To resolve this, map the doorbell between offload and
enable, so that driver is ready to receive the unsolicited packets and
arm the CQ as soon as FW enable is performed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Moved the 'waiting for upload/offload completion' logic to respective
functions as it is called in multiple places. Also this is done in
preperation for the next patch.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Software FCoE target always advertises RETRY bit even when there are no
tape LUNs behind the target. This causes the driver to enable FW support
for sequence level error recovery and perform REC/SRR. This patch
arrests the behavior by not enabling SLER feature for this target.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
These calls are followed by calls to memcpy() on the same memory area, so they
can be safely removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the bnx2fc_xxx versions as they are basically the same.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
We have fcoe_link_speed_update() in libfcoe ready for use now, take out the
bnx2fc version which is almost the same.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Adds support to fcoe_port's newly added get_netdev fucntion pointer for bnx2fc.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
This patch adds support for the new fcoe_sysfs
control interface to bnx2fc.ko. It keeps the deprecated
interface in tact and therefore either the legacy
or the new control interfaces can be used. A mixed mode
is not supported. A user must either use the new
interfaces or the old ones, but not both.
The fcoe_ctlr's link state is now driven by both the
netdev link state as well as the fcoe_ctlr_device's
enabled attribute. The link must be up and the
fcoe_ctlr_device must be enabled before the FCoE
Controller starts discovery or login.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
This patch does a few things.
1) Makes /sys/bus/fcoe/ctlr_{create,destroy} interfaces.
These interfaces take an <ifname> and will either
create an FCoE Controller or destroy an FCoE
Controller depending on which file is written to.
The new FCoE Controller will start in a DISABLED
state and will not do discovery or login until it
is ENABLED. This pause will allow us to configure
the FCoE Controller before enabling it.
2) Makes the 'mode' attribute of a fcoe_ctlr_device
writale. This allows the user to configure the mode
in which the FCoE Controller will start in when it
is ENABLED.
Possible modes are 'Fabric', or 'VN2VN'.
The default mode for a fcoe_ctlr{,_device} is 'Fabric'.
Drivers must implement the set_fcoe_ctlr_mode routine
to support this feature.
libfcoe offers an exported routine to set a FCoE
Controller's mode. The mode can only be changed
when the FCoE Controller is DISABLED.
This patch also removes the get_fcoe_ctlr_mode pointer
in the fcoe_sysfs function template, the code in
fcoe_ctlr.c to get the mode and the assignment of
the fcoe_sysfs function pointer to the fcoe_ctlr.c
implementation (in fcoe and bnx2fc). fcoe_sysfs can
return that value for the mode without consulting the
LLD.
3) Make a 'enabled' attribute of a fcoe_ctlr_device. On a
read, fcoe_sysfs will return the attribute's value. On
a write, fcoe_sysfs will call the LLD (if there is a
callback) to notifiy that the enalbed state has changed.
This patch maintains the old FCoE control interfaces as
module parameters, but it adds comments pointing out that
the old interfaces are deprecated.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
gcc 4.8 warns because the memset only clears sizeof(char *) bytes, not
the whole buffer. Use the correct buffer size and clear the whole sense
buffer.
/backup/lsrc/git/linux-lto-2.6/drivers/scsi/bnx2fc/bnx2fc_io.c: In
function 'bnx2fc_parse_fcp_rsp':
/backup/lsrc/git/linux-lto-2.6/drivers/scsi/bnx2fc/bnx2fc_io.c:1810:41:
warning: argument to 'sizeof' in 'memset' call is the same expression as
the destination; did you mean to provide an explicit length?
[-Wsizeof-pointer-memaccess]
memset(sc_cmd->sense_buffer, 0, sizeof(sc_cmd->sense_buffer));
^
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The most important feature of this patch set is the new async infrastructure
that makes sure async_synchronize_full() synchronizes all domains and allows
us to remove all the hacks (like having scsi_complete_async_scans() in the
device base code) and means that the async infrastructure will "just work" in
future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
/uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
=y2sh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
Use list_for_each_entry_safe() instead of explicit cast to avoid relying on
struct layout
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During parity errors, the ramrods are not issued to FW. bnx2fc waits for the
timeout value, and proceeds with cleaning up the IOs. Since we are already
out-of-sync with FW, cleanup commands timeout too, and do not get the
completion. This operation takes 36 secs for each session to upload causing
huge delays. To fix this, bnx2fc now gets a PARITY_ERROR from cnic driver, and
upon failure, the driver does not issue any commands to the FW and finishes the
upload process sooner.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
bnx2fc had an assumption that the fcoe interface will always start on the vlan
dev. However, some switch implementations (Eg., HP virtual connect FlexFabric)
expects the fcoe interface to be started on physical interface. Do not error
out if the netdev is not a vlan dev.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Deduplication of formats and consolidating tests
makes the object much smaller.
Add bnx2fc_debug.c, add functions for a few logging
functions (BNX2FC_IO_DBG, BNX2FC_TGT_DBG, BNX2FC_HBA_DBG).
Use printf extension %pV.
Add and use pr_fmt and pr_<level>.
Move the debug #include below structure definitions.
$ size drivers/scsi/bnx2fc/built-in.o*
text data bss dec hex filename
101563 1165 24976 127704 1f2d8 drivers/scsi/bnx2fc/built-in.o.new
138473 1109 33400 172982 2a3b6 drivers/scsi/bnx2fc/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since bnx2fc_percpu_thread_create() creates percpu kthread, it makes
sense to use kthread_create_on_node() to get proper NUMA affinity for
kthread stack.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The libfc is used by fcoe but fcoe agnostic,
and therefore should not have any fcoe references.
So renaming fcoe_dev_stats from libfc as its for fc_stats.
After that libfc is fcoe string free except some strings for
Open-FCoE.org.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1. When FCoE offload driver is registered, copy its capabilities to the chip
scratchpad.
2. Copy FCoE/iSCSI MAC addresses in aligned manner to chip scratchpad.
3. Add FCoE/iSCSI statistics collection support
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch has the SW FCoE driver and the bnx2fc
driver make use of the new fcoe_sysfs API added
earlier in this patch series.
After this patch a fcoe_ctlr_device is allocated with
private data in this order.
+------------------+ +------------------+
| fcoe_ctlr_device | | fcoe_ctlr_device |
+------------------+ +------------------+
| fcoe_ctlr | | fcoe_ctlr |
+------------------+ +------------------+
| fcoe_interface | | bnx2fc_interface |
+------------------+ +------------------+
libfcoe also takes part in this new model since it
discovers and manages fcoe_fcf instances. The memory
allocation is different for FCFs. I didn't want to
impact libfcoe's fcoe_fcf processing, so this patch
creates fcoe_fcf_device instances for each discovered
fcoe_fcf. The two are paired using a (void * priv)
member of the fcoe_ctlr_device. This allows libfcoe
to continue maintaining its list of fcoe_fcf instances
and simply attaches and detaches them from existing
or new fcoe_fcf_device instances.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently the fcoe_ctlr associated with an interface is allocated
as a member of struct bnx2fc_interface. This causes problems when
when later patches attempt to use the new fcoe_sysfs APIs which
allow us to allocate the bnx2fc_interface as private data to a
fcoe_ctlr_device instance. The problem is that libfcoe wants to
be able use pointer math to find a fcoe_ctlr's fcoe_ctlr_device
as well as finding a fcoe_ctlr_device's assocated fcoe_ctlr. To
do this we need to allocate the fcoe_ctlr_device, with private
data for the LLD. The private data will contain the fcoe_ctlr
and its private data will be the bnx2fc_interface.
+-------------------+
| fcoe_ctlr_device |
+-------------------+
| fcoe_ctlr |
+-------------------+
| bnx2fc_interface |
+-------------------+
This prep work will allow us to go from a fcoe_ctlr_device
instance to its fcoe_ctlr as well as from a fcoe_ctlr to its
fcoe_ctlr_device once the fcoe_sysfs API is in use (later
patches in this series).
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the task management IO times out, or a flush operation is performed while
task management IO is pending, driver is not cleaning up the IO. This patch
cleans up the IO for the above cases.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When IO abort times out during eh_abort or a flush operation is performed while
abort is pending, the driver is not cleaning up the IO and thus not reducing
the IO reference count. With this change, as part of explicit logout, the IO is
cleaned up.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit 907c07d451 added more cases to do FLOGI
retry on receiving bad response. Remove the code that drops the packet and
allow the stack to handle bad FLOGI response.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
=IH8T
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
Pull SCSI updates from James Bottomley:
"This is primarily another round of driver updates (lpfc, bfa, fcoe,
ipr) plus a new ufshcd driver. There shouldn't be anything
controversial in here (The final deletion of scsi proc_ops which
caused some build breakage has been held over until the next merge
window to give us more time to stabilise it).
I'm afraid, with me moving continents at exactly the wrong time,
anything submitted after the merge window opened has been held over to
the next merge window."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
[SCSI] ipr: Driver version 2.5.3
[SCSI] ipr: Increase alignment boundary of command blocks
[SCSI] ipr: Increase max concurrent oustanding commands
[SCSI] ipr: Remove unnecessary memory barriers
[SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
[SCSI] ipr: Fix target id allocation re-use problem
[SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
[SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
[SCSI] bfa: Update the driver version to 3.0.23.0
[SCSI] bfa: BSG and User interface fixes.
[SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
[SCSI] bfa: Move service parameter programming logic into firmware.
[SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
[SCSI] bfa: Flash controller IOC pll init fixes.
[SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
[SCSI] bfa: Modify ISR to process pending completions
[SCSI] bfa: Add fc host issue lip support
[SCSI] mpt2sas: remove extraneous sas_log_info messages
[SCSI] libfc: fcoe_transport_create fails in single-CPU environment
[SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
...
As with the fcoe sw transport, the bnx2fc packet handler function runs only in
softirq context. Theres no need to disable bottom halves here
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull networking fixes from David Miller:
1) L2TP doesn't get autoloaded when you try to open an L2TP socket due
to a missing module alias, fix from Benjamin LaHaise.
2) Netlabel and RDS should propagate gfp flags given to them by
callers, fixes from Dan Carpeneter.
3) Recursive locking fix in usbnet wasn't bulletproof and can result in
objects going away mid-flight due to races, fix from Ming Lei.
4) Fix up some confusion about a bool module parameter in netfilter's
iptable_filter and ip6table_filter, from Rusty Russell.
5) If SKB recycling is used via napi_reuse_skb() we end up with
different amounts of headroom reserved than we had at the original
SKB allocation. Fix from Eric Dumazet.
6) Fix races in TG3 driver ring refilling, from Michael Chan.
7) We have callbacks for IPSEC replay notifiers, but some call sites
were not using the ops method and instead were calling one of the
implementations directly. Oops. Fix from Steffen Klassert.
8) Fix IP address validation properly in the bonding driver, the
previous fix only works with netlink where the subnet mask and IP
address are changed in one atomic operation. When 'ifconfig' ioctls
are used the IP address and the subnet mask are changed in two
distinct operations. Fix from Andy Gospodarek.
9) Provide a sky2 module operation to work around power management
issues with some BIOSes. From Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
usbnet: consider device busy at each recieved packet
bonding: remove entries for master_ip and vlan_ip and query devices instead
netfilter: remove forward module param confusion.
usbnet: don't clear urb->dev in tx_complete
usbnet: increase URB reference count before usb_unlink_urb
xfrm: Access the replay notify functions via the registered callbacks
xfrm: Remove unused xfrm_state from xfrm_state_check_space
RDS: use gfp flags from caller in conn_alloc()
netlabel: use GFP flags from caller instead of GFP_ATOMIC
l2tp: enable automatic module loading for l2tp_ppp
cnic: Fix parity error code conflict
tg3: Fix RSS ring refill race condition
sky2: override for PCI legacy power management
net: fix napi_reuse_skb() skb reserve
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
The recently added parity error handling used an error code that was
already defined for a different error. This could lead to bnx2x
firmware assert. We need to fix this with new error codes that are
defined for parity error only.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
This allows us to use scsilun_to_int without an ugly cast.
Fix up places that use scsilun_to_int on fcp->fc_lun accordingly.
In fc target, this leaves ft_cmd.lun unused, so remove it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
with Tx only section for single cached SGEs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are 255 NPIV ports, and the interface is brought down & up, both
physical and NPIV ports are logged off and never logged back in. Since
discovery happens on single CPU, XID resources on that CPU will be limited,
which when exhausted the discovery fails. Increase the XID resource range to
ensure that the discovery completes successfully. Also ensure that
fc_exch_mgr_alloc() doesn't fail on the system that has lower number of CPUs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Host drops sessions when flood of unsolicited LOGOs are received from the
target. Because of unsufficient PLOGI retries, upon exceeding the retry count
of 3, the target sessions are dropped. Increased the retry count to 255 to
allow sufficient retries in this scenario.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
System panics while accessing stale pointer - timer_work_queue - in the IO path
before bnx2fc_stop is called. Fix is to destroy the workqueue after the destroy
operation is complete.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When SRR LS_ACC is dropped, the driver was not issuing ABTS for SRR when it
times out. Since the target received SRR, it was able to send the XFER_RDY and
the the original IO request completed successfully. In this condition ABTS was
not sent during bnx2fc_srr_compl(). Fix this by first checking for ELS timeout
and issue ABTS before checking if original IO request is complete.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the IO and the corresponding ABTS are not responded by a target, cleanup the
IO and issue explicit logout when ulp timer expires while waiting for ABTS to
complete. Wait for the session to be ready before returning to the SCSI layer.
If the session is not ready let the SCSI-ml escalate the error recovery.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support for get_lesb so that the valid statistics are returned by the
remote peer when RLS command is issued.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link may not be up when the driver receives ulp_start event, and hence
fcoe_ctlr_link_up is not called. Call fcoe_ctlr_link_up during
indicate_netevent only when the interface is enabled. (It has to be called when
enabled because that is an indication that the vlan discovery is completed).
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Gracefully handle bnx2fc_map_sg failure, so that queuecommand returns host busy
and SCSI-ml can retry the IO.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_dma_map doesn't work for NPIV since vport dev isn't fully initialized.
For more details: http://marc.info/?l=linux-scsi&m=118312448030633&w=2 and
commit - c59fd9ebc4.
Signed-off-by: Nithin Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Firmware asserts when the same CQE is armed twice. This scenario happens during
RSCN stress tests as driver incorrects arms the CQ after the session is
offloaded.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It is not required to hold rtnl_lock and bnx2fc_dev_lock when calling
bnx2fc_if_destroy, as the locking is only required to serialize creation and
deletion of fcoe instances. More importantly, this unnecessary locking causes
deadlock as bnx2fc_if_destroy calls fc_remove_host holding rtnl_lock.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When bnx2fc receives an UNREGISTER event on a vlan interface it calls
destroy on all interfaces that matches the physical interface. Add
vlan_id check to destroy only the vlan interface that generated the
event.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ABTS was not issued for timed out REC, as REC completion handler exits out if
the IO completed. Check for timed out REC and issue ABTS before proceeding with
further processing in REC completion handler. Also, initialize rec_retry and
srr_retry before starting the IO.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Link up event is generated to the driver even before vlan discovery has
started. Because of this driver can send discovery solicitation on a stale
vlan. Call fcoe_ctlr_link_up() only when the driver is in enabled state, which
implies the vlan discovery is complete before sending solicitation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the max receive frame size is changed during link down, the driver uses the
same value after linkup unless it is reset to default.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is already called in the right context with rtnl_lock and dev_mutex
held.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Increase it to NVRAM configured limit or 1024 whichever is less.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
bnx2x driver would obtain the WWNN/WWPN from the shared memory and can be
obtained by the bnx2fc driver via ndo_fcoe_get_wwn.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As an initiator, driver need not handle incoming ABTS. It initiates an ABTS if
any IO requests time out.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Free session resources before rport logoff
- Do not free session resources in bnx2fc_alloc_session_resc() as it is handled
in caller's error handling path.
- Do not call bnx2fc_free_session_resc() if bnx2fc_init_tgt() fails as cq_lock
is not yet initialized.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There exists a race condition between CQ doorbell unmap and IO completion path
that arms the CQ which causes a NULL dereference. Protect the ctx_base with
cq_lock to avoid this. Also, wait for the CQ doorbell to be successfully mapped
before arming the CQ.
Also, do not count uncolicited CQ completions for free_sqes.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During the unsolicited LOGO processing, the session is uploaded and offloaded
after the relogin is complete. In between any new IOs are errored back as the
upload completion flag is set. Upon exhausting the retry count, the application
fails the IOs. Return target busy for all the cases when session is not ready.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CFC_DELETE is issued 2 secs after CONN_TERM is completed. If the session is
uploaded and offloaded immediately, it has to wait for the connection id to be
available.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since this flag was never cleared, the driver does not wait for firmware
destroy completions, causing missed KCQEs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since the driver holds the reference for vlan netdev, the reference has to be
released by the driver when the vlan device is removed. Driver handles this in
NETDEV_UNREGISTER event.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move interface specific cleanup functionality to from bnx2fc_if_destroy to
bnx2fc_interface_cleanup. Do not access interface/hba in bnx2fc_if_destroy as
by the time this function is called interface may already be destroyed. This
patch is in preparation to handle NETDEV_UNREGISTER on a vlan device.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change them to bnx2fc_interface_setup/bnx2fc_interface_cleanup in preperation
for the patches to follow. Interface specific cleanup functionality will be
moved to bnx2fc_interface_cleanup.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When NPIV ports are created/deleted rapidly there is a race condition between
bnx2fc_vport_destroy() from sysfs and bnx2fc_flogi_resp(), which could try to
delete the NPIV port from the list twice. Fix is to loop through the list of
NPIV ports to find a match, and only when it exists remove it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During sequence cleanup, an additional reference for an IO has been
taken. Because of this, the IO is never released into the free list.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Look up p->work_list to process cq completions, and correct the error check for
thread creation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reset max receive frame size every time before attempting FLOGI. Without this,
the stale MFS value will be used.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no need to cache the ptype in fcoe_rcv_info struct as it is never
used anywhere.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When there is a single BD for the entire data to be transmitted, use the BD
inside the SGL context and set the cached SGE indication in the task context
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver advertises its support for 'retry' bit and 'conf completion' bit in PRLI
params to enable support for 'sequence level error recovery'
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Program the firmware task structure with init_flags indicating the device is
'sequence level error recovery' capable.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver decides to initiate REC on REC_TOV timer pop. The firmware maintains the
REC timer and informs the driver as a firmware error message, which is an
unsolicited event to the driver. Driver also issues REC on other unsolicited
events from firmware that indicate data loss.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the devices that support sequence level error recovery, based on the REC
response, the firmware has to be informed about the offset from which the
retransmission should happen. Driver initiates sequence cleanup task to
firmware so that the firmware can program the task. Upon the sequence cleanup
completion, SRR is issued to retransmit the sequence.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on PRLI response, identify if the target is FCP-2 (seq level error
recovery) capable, and appropriately set the corresponding CONF, REC flags when
offloading the session.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently, bnx2fc has a hba structure that can work with only a single vlan
interface. When there is a change in vlan id, it does not have the capability
to switch to different vlan interface. To solve this problem, a new structure
called 'interface' has been introduced, and each hba can now have multiple
interfaces, one per vlan id.
Most of the patch is a moving the interface specific fields from hba to the
interface structure, and appropriately modifying the dereferences. A list of
interfaces (if_list) is maintained along with adapter list. During a create
call, the interface structure is allocated and added to if_list and deleted &
freed on a destroy call. Link events are propagated to all interfaces
belonging to the hba.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (77 commits)
[SCSI] fix crash in scsi_dispatch_cmd()
[SCSI] sr: check_events() ignore GET_EVENT when TUR says otherwise
[SCSI] bnx2i: Fixed kernel panic due to illegal usage of sc->request->cpu
[SCSI] bfa: Update the driver version to 3.0.2.1
[SCSI] bfa: Driver and BSG enhancements.
[SCSI] bfa: Added support to query PHY.
[SCSI] bfa: Added HBA diagnostics support.
[SCSI] bfa: Added support for flash configuration
[SCSI] bfa: Added support to obtain SFP info.
[SCSI] bfa: Added support for CEE info and stats query.
[SCSI] bfa: Extend BSG interface.
[SCSI] bfa: FCS bug fixes.
[SCSI] bfa: DMA memory allocation enhancement.
[SCSI] bfa: Brocade-1860 Fabric Adapter vHBA support.
[SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.
[SCSI] bfa: Added Fabric Assigned Address(FAA) support
[SCSI] bfa: IOC bug fixes.
[SCSI] bfa: Enable ASIC block configuration and query.
[SCSI] bnx2i: Updated copyright and bump version
[SCSI] bnx2i: Modified to skip CNIC registration if iSCSI is not supported
...
Fix up some trivial conflicts in:
- drivers/scsi/bnx2fc/{bnx2fc.h,bnx2fc_fcoe.c}:
Crazy broadcom version number conflicts
- drivers/target/tcm_fc/tfc_cmd.c
Just trivial cleanups done on adjacent lines
The bnx2fc driver needs to handle netdev events on VLAN devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deleting NPIV port causes a kernel panic when the NPIV port is in the same zone
as the physical port and shares the same LUN. This happens due to the fact that
vport destroy and unsolicited ELS are scheduled to run on the same workqueue,
and vport destroy destroys the lport and the unsolicited ELS tries to access
the invalid lport. This patch fixes this issue by maintaining a list of valid
lports and verifying if the lport is valid or not before accessing it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Do not set io_req->sc_cmd to NULL until bnx2fc_unmap_sg_list() is called to
enable it to unmap the DMA mappings.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
NIC partitioned interfaces reports the speed of 2500 which was not handled by
the driver.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
New FW/HSI (7.0):
- Added support to 578xx chips
- Improved HSI - much less driver's direct access to the FW internal
memory needed.
New implementation of the HSI handling layer in the bnx2x (bnx2x_sp.c):
- Introduced chip dependent objects that have chip independent interfaces
for configuration of MACs, multicast addresses, Rx mode, indirection table,
fast path queues and function initialization/cleanup.
- Objects functionality is based on the private function pointers, which
allows not only a per-chip but also PF/VF differentiation while still
preserving the same interface towards the driver.
- Objects interface is not influenced by the HSI changes which do not require
providing new parameters keeping the code outside the bnx2x_sp.c invariant
with regard to such HSI chnages.
Changes in a CNIC, bnx2fc and bnx2i modules due to the new HSI.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Use fc_exch_mgr_list_clone to setup em for npiv port.
Also remove redundant vport and lport initializations.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FW may take more time cleaning up IOs issued to multiple targets.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
David S. Miller
Chad Dupuis
Anish Bhatt
Saurav Kashyap
Hannes Reinecke
Neil Horman
Maurizio Lombardi
Linus Torvalds
Ingo Molnar
Dongsheng Yang
Srivatsa S. Bhat
Michael Chan
Eddie Wai
James Bottomley
Joe Perches
Robert Love
Bhanu Prakash Gollapudi
Julia Lawall
Cyril Roelandt
Greg Kroah-Hartman
Yi Zou
Masanari Iida
Andi Kleen
Eric Dumazet
Vasu Dev
Barak Witkowski
Cong Wang
Andy Grover
Nithin Nayak Sujir
Jiri Pirko
Ian Campbell
Jeff Kirsher
Vlad Zolotarov