Separate data-ready configuration parameters for INT1 and INT2 pins in
st_sensor_data_ready_irq data structure. That change will be use to
properly support LIS2DW12 accel sensor.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce register mask for data-ready status register since
pressure sensors (e.g. LPS22HB) export just two channels
(BIT(0) and BIT(1)) and BIT(2) is marked reserved while in
st_sensors_new_samples_available() value read from status register
is masked using 0x7.
Moreover do not mask status register using active_scan_mask since
now status value is properly masked and if the result is not zero the
interrupt has to be consumed by the driver. This fix an issue on LPS25H
and LPS331AP where channel definition is swapped respect to status
register.
Furthermore that change allows to properly support new devices
(e.g LIS2DW12) that report just ZYXDA (data-ready) field in status register
to figure out if the interrupt has been generated by the device.
Fixes: 97865fe413 (iio: st_sensors: verify interrupt event to status)
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These ADCs are marketed as single-channel 22 bit delta-sigma ADCs, but
in reality their resolution is 21 bit with an overrange or underrange
of 12% beyond Vref. In other words, "full scale" means +/- 2^20.
This driver does not explicitly signal back to the user when an
overrange or underrange occurs, but the user can detect it by comparing
the raw value to +/- 2^20 (or the scaled value to Vref).
The chips feature an extended temperature range and high accuracy,
low noise characteristics, but their conversion times are slow with
up to 80 ms +/- 2% (on the MCP3550-50).
Hence, unlike the other ADCs supported by the driver, conversion does
not take place in realtime upon lowering CS. Instead, CS is asserted
for 8 usec to start the conversion. After waiting for the duration of
the conversion, the result can be fetched. While waiting, control of
the bus is ceased so it may be used by a different device.
After the result has been fetched and 10 us have passed, the chip goes
into shutdown and an additional power-up delay of 144 clock periods is
then required to wake the analog circuitry upon the next conversion
(footnote below table 4-1, page 16 in the spec).
Optionally, the chips can be used in so-called "continuous conversion
mode": Conversions then take place continuously and the last result may
be fetched at any time without observing a delay. The mode is enabled
by permanently driving CS low, e.g. by wiring it to ground. The driver
only supports "single conversion mode" for now but should be adaptable
to "continuous conversion mode" with moderate effort.
The chips clock out a 3 byte word, unlike the other ADCs supported by
the driver which all have a lower resolution than 16 bit and thus make
do with 2 bytes. Calculate the word length on probe by rounding up the
resolution to full bytes. Crucially, if the clock idles low, the
transfer is preceded by a useless Data Ready bit which increases its
length from 24 bit to 25 bit = 4 bytes (section 5.5 in the spec).
Autosense this based on the SPI slave's configuration.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The IIO subsystem is redefining iio_dev->mlock to be used by
the IIO core only for protecting device operating mode changes.
ie. Changes between INDIO_DIRECT_MODE, INDIO_BUFFER_* modes.
In this driver, mlock was being used to protect hardware state
changes. Replace it with a driver private lock.
Also, as there are state changes in the ad7192_ write_raw function, a lock
is added to prevent the concurrent state changes.
Signed-off-by: Aastha Gupta <aastha.gupta4104@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the ABI documentation, the shunt resistor value should be
specificied in Ohm. As this is also used/documented for the MAX9611,
use the same for the INA2xx driver.
This poses an ABI break for anyone actually altering the shunt value
through the sysfs interface, it does not alter the default value nor
a value set from the devicetree.
Minor change: Fix comment, 1mA is 10^-3A.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce FIFO ops data structure to contain FIFO related parameters
in order to properly support more devices in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move FIFO decimator info in st_lsm6dsx_sensor_settings list since
decimator registers are exported in register map just in
lsm6ds3/lsm6ds3h/lsm6dsl/lsm6dsm sensors and not in other compliant
devices
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Separate fifo mode and max fifo sample rate configuration.
That change will be necessary to reuse st_lsm6dsx_set_fifo_mode()
routine and to support more devices in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Express max fifo depth in ST_LSM6DSX_SAMPLE_SIZE instead of in bytes.
That change will be necessary to properly support more devices
in st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the of_device_get_match_data() helper instead of open coding.
Note that the rcar-gyroadc driver is used with DT only, so there's
always a valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The rcar-gyroadc driver compiles fine on other platforms, hence increase
compile coverage.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On 64-bit:
drivers/iio/adc/rcar-gyroadc.c: In function 'rcar_gyroadc_parse_subdevs':
drivers/iio/adc/rcar-gyroadc.c:352:15: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
childmode = (unsigned int)of_id->data;
^
Cast the pointer to uintptr_t instead of unsigned int to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Dropping the extra lock (used for protecting the write frequency) by
expanding the buffer lock to cover both buffer and state protection.
Doing this by introducing a new function (__ade7753_spi_write_reg_16)
making buffer changes without locking the state, to avoid nested locks
while making device frequency changes.
Signed-off-by: Himanshi Jain <himshijain.hj@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver explicitly creates the in_illuminance0_integration_time sysfs
attribute outside the IIO core. This attribute is available in the IIO
core so this patches migrates the attribute to be created by
the iio_chan_spec.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The length of the 'tsl2x7x_settings' variable within the tsl2X7X_chip
structure makes some of the line lengths greater than 80 characters for
upcoming patches. This patch shortens the name of the 'tsl2x7x_settings'
variable in this structure to just 'settings' to improve code
readability.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The reported scale was only correct for the default settings of 100 ms
integration time and gain 1.
This aligns the reported scale with the behaviour of any other IIO driver
and the documented ABI, but may require userspace changes if someone uses
non-default settings.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of manually iterating the array of allowed gain values, use
find_closest. Storing the current gain setting avoids accessing the
hardware on each query.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of reading the value from the register on each query, store the
set value.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This improves code uniformity (range checks for als_gain are also done
in the setter). Also unmangle rounding and calculation of register value.
The calculated integration time it_ms is required in the next patch of
the series.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
KXTF9 has mostly compatible register layout to KXCJK accelerometer.
There is no motion direction interrupt support, but there is tap
direction detection instead (not implemented in this patch).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make sampling_frequency_avail per-type - like sampling_frequency is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation for KXTF9 support, make sampling_frequency_avail
attribute dynamic.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Extract reporting of motion event direction from interrupt handler,
as it is not supported by KXTF9.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix INT_CTRL1 bit names to match register name and add names
for INT_SRC1 bits.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor ODR/WUF setting code in preparation of KXTF9 support.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
'mma8452_read_thresh' and 'mma8452_write_thresh' functions
does more than just read/write threshold values.
They also handle IIO_EV_INFO_HIGH_PASS_FILTER_3DB and
IIO_EV_INFO_PERIOD therefore renaming to generic names.
Improves code readability, no impact on functionality.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch, forgetting to put a thermal-zones DT node would
result in the driver failing to probe.
It should be perfectly acceptable to have the driver probe even if no
thermal-zones DT is found. However, it shouldn't want to fail if the
thermal registering fail for any other reason (waiting for other drivers
for example) so check on ENODEV only.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver has a get_temp function used by the thermal framework that
uses pm functions.
However, the driver isn't registered in pm before it is registered in
thermal framework, resulting in the pm_resume not being called and thus
the IP not enabled.
When the IP is disabled, the raw temp value is always 0. With the
devices currently supported, it isn't a problem since with their
respective formula, they return a really cold SoC temperature which
isn't a problem for the thermal framework. But for future SoC that have
a different formula, it could return a critically hot temperature,
forcing the thermal framework to shutdown the board.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch provides an iio device driver for DS4422/DS4424 chips that support
two/four channel 7-bit Sink/Source Current DAC.
Signed-off-by: Ismail H. Kose <Ismail.Kose@maximintegrated.com>
Signed-off-by: Ismail H. Kose <ihkose@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ismail H. Kose <ihkose@gmail.com>
Signed-off-by: Ismail H. Kose <Ismail.Kose@maximintegrated.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A couple of serious fixes (use after free and blacklist for WRITE
SAME). One error leg fix (write_pending failure) and one user
experience problem (do not override max_sectors_kb) and one minor
unused function removal.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=X/MK
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
- a couple of serious fixes: use after free and blacklist for WRITE
SAME
- one error leg fix: write_pending failure
- one user experience problem: do not override max_sectors_kb
- one minor unused function removal
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ibmvscsis: Fix write_pending failure path
scsi: libiscsi: Remove iscsi_destroy_session
scsi: libiscsi: Fix use-after-free race during iscsi_session_teardown
scsi: sd: Do not override max_sectors_kb sysfs setting
scsi: sd: Implement blacklist option for WRITE SAME w/ UNMAP
Pull i2c fixes from Wolfram Sang:
"I2C has three driver fixes for the newly introduced drivers and one ID
addition for the i801 driver"
* 'i2c/for-current-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: make structure stm32f7_setup static const
i2c: ensure termination of *_device_id tables
i2c: i801: Add support for Intel Cedar Fork
i2c: stm32f7: fix setup structure
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just remove
the mmc bounce buffer code altogether, as it has practically no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0WJ+
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
- Suspend fix for Samsung Exynos SoCs where we need to keep clks on
across suspend
- Two critical clk markings for clks that shouldn't ever turn off on
Rockchip SoCs
- A fix for a copy-paste mistake on Rockchip rk3128 causing some clks to
touch the same bit and trample over one another
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=jV1S
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
- build fix to export the clk_bulk_prepare() symbol
- suspend fix for Samsung Exynos SoCs where we need to keep clks on
across suspend
- two critical clk markings for clks that shouldn't ever turn off on
Rockchip SoCs
- a fix for a copy-paste mistake on Rockchip rk3128 causing some clks
to touch the same bit and trample over one another
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: samsung: exynos4: Enable VPLL and EPLL clocks for suspend/resume cycle
clk: Export clk_bulk_prepare()
clk: rockchip: add sclk_timer5 as critical clock on rk3128
clk: rockchip: fix up rk3128 pvtm and mipi_24m gate regs error
clk: rockchip: add pclk_pmu as critical clock on rk3128
- Updates for various platforms
- boot log updates for upcoming HS48 family of cores (dual issue)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lcdb
-----END PGP SIGNATURE-----
Merge tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC udpates from Vineet Gupta:
- updates for various platforms
- boot log updates for upcoming HS48 family of cores (dual issue)
* tag 'arc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-hsdk]: Add reset controller node to manage ethernet reset
ARC: [plat-hsdk]: Temporary fix to set CPU frequency to 1GHz
ARC: fix allnoconfig build warning
ARCv2: boot log: identify HS48 cores (dual issue)
ARC: boot log: decontaminate ARCv2 ISA_CONFIG register
arc: remove redundant UTS_MACHINE define in arch/arc/Makefile
ARC: [plat-eznps] Update platform maintainer as Noam left
ARC: [plat-hsdk] use actual clk driver to manage cpu clk
ARC: [*defconfig] Reenable soft lock-up detector
ARC: [plat-axs10x] sdio: Temporary fix of sdio ciu frequency
ARC: [plat-hsdk] sdio: Temporary fix of sdio ciu frequency
ARC: [plat-axs103] Add temporary quirk to reset ethernet IP
Pull block fixes from Jens Axboe:
"A collection of fixes for this series. This contains:
- NVMe pull request from Christoph, one uuid attribute fix, and one
fix for the controller memory buffer address for remapped BARs.
- use-after-free fix for bsg, from Benjamin Block.
- bcache race/use-after-free fix for a list traversal, fixing a
regression in this merge window. From Coly Li.
- null_blk change configfs dependency change from a 'depends' to a
'select'. This is a change from this merge window as well. From me.
- nbd signal fix from Josef, fixing a regression introduced with the
status code changes.
- nbd MAINTAINERS mailing list entry update.
- blk-throttle stall fix from Joseph Qi.
- blk-mq-debugfs fix from Omar, fixing an issue where we don't
register the IO scheduler debugfs directory, if the driver is
loaded with it. Only shows up if you switch through the sysfs
interface"
* 'for-linus' of git://git.kernel.dk/linux-block:
bsg-lib: fix use-after-free under memory-pressure
nvme-pci: Use PCI bus address for data/queues in CMB
blk-mq-debugfs: fix device sched directory for default scheduler
null_blk: change configfs dependency to select
blk-throttle: fix possible io stall when upgrade to max
MAINTAINERS: update list for NBD
nbd: fix -ERESTARTSYS handling
nvme: fix visibility of "uuid" ns attribute
bcache: use llist_for_each_entry_safe() in __closure_wake_up()
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
-----BEGIN PGP SIGNATURE-----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=Iu63
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Bring initialisation of user space undefined instruction handling
early (core_initcall) since late_initcall() happens after modprobe in
initramfs is invoked. Similar fix for fpsimd initialisation
- Increase the kernel stack when KASAN is enabled
- Bring the PCI ACS enabling earlier via the
iort_init_platform_devices()
- Fix misleading data abort address printing (decimal vs hex)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Ensure fpsimd support is ready before userspace is active
arm64: Ensure the instruction emulation is ready for userspace
arm64: Use larger stacks when KASAN is selected
ACPI/IORT: Fix PCI ACS enablement
arm64: fix misleading data abort decoding
- fix PPC XIVE interrupt delivery
- fix x86 RCU breakage from asynchronous page faults when built without
PREEMPT_COUNT
- fix x86 build with -frecord-gcc-switches
- fix x86 build without X86_LOCAL_APIC
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJZ18AmAAoJEED/6hsPKofoPEwH+waDVIeS+s38G8HkiB8PoVww
bAhAV6Aj3muOI49KtwBt+qyC8nOQHpwPCNqjmagOv1GEYSwJ4gKKoJ6Xl9rOsxau
GT0xDgVDbrzIb/PTFL+7bDjsyMxf89utIfoBL8i37uznzB35+QFlvy4mLgKntAh0
1/tYDzgrQxuxH5RF4DbFstoPFjw1kdxpXRzHdngsV13bS87PAG9j7A0l7orLtXZg
qxlTh2SvCSr4B0hOZGG/Pc0aIAxLh8kRD6NaU05raKgzQLJa5sxJ0Yr+RbskfqQb
7B98X1Ygb1BjBOFxy+Je5IamKt4ICTY1B0v1ivs0qZ+mgxG59FWuQlR0pww/8Ug=
=ay5S
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
- fix PPC XIVE interrupt delivery
- fix x86 RCU breakage from asynchronous page faults when built without
PREEMPT_COUNT
- fix x86 build with -frecord-gcc-switches
- fix x86 build without X86_LOCAL_APIC
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: add X86_LOCAL_APIC dependency
x86/kvm: Move kvm_fastop_exception to .fixup section
kvm/x86: Avoid async PF preempting the kernel incorrectly
KVM: PPC: Book3S: Fix server always zero from kvmppc_xive_get_xive()
- a fix for iwpm netlink usage
- a fix for error unwinding in mlx5
- two fixes to vlan handling in qedr
- a couple small i40iw fixes
-----BEGIN PGP SIGNATURE-----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=17J/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"This is a pretty small pull request. Only 6 patches in total. There
are no outstanding -rc patches on the mailing list after this pull
request, so only if some new issues are discovered in the remainder of
the rc cycles will you hear from me again.
Summary:
- a fix for iwpm netlink usage
- a fix for error unwinding in mlx5
- two fixes to vlan handling in qedr
- a couple small i40iw fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
i40iw: Fix port number for query QP
i40iw: Add missing memory barriers
RDMA/qedr: Parse vlan priority as sl
RDMA/qedr: Parse VLAN ID correctly and ignore the value of zero
IB/mlx5: Fix label order in error path handling
RDMA/iwpm: Properly mark end of NL messages
Pull btrfs fixes from David Sterba:
"Two more fixes for bugs introduced in 4.13.
The sector_t problem with 32bit architecture and !LBDAF config seems
serious but the number of affected deployments is hopefully low.
The clashing status bits could lead to a confusing in-memory state of
the whole-filesystem operations if used with the quota override sysfs
knob"
* 'for-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix overlap of fs_info::flags values
btrfs: avoid overflow when sector_t is 32 bit
DW ethernet controller on HSDK hangs sometimes after SW reset, so
add reset node to make possible to reset DW ethernet controller HW.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull overlayfs fixes from Miklos Szeredi:
"Fix a regression in 4.14 and one in 4.13. The latter is a case when
Docker is doing something it really shouldn't and gets away with it.
We now print a warning instead of erroring out.
There are also fixes to several error paths"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix regression caused by exclusive upper/work dir protection
ovl: fix missing unlock_rename() in ovl_do_copy_up()
ovl: fix dentry leak in ovl_indexdir_cleanup()
ovl: fix dput() of ERR_PTR in ovl_cleanup_index()
ovl: fix error value printed in ovl_lookup_index()
ovl: fix may_write_real() for overlayfs directories
Nine small fixes, really nothing that stands out.
A work around for a spurious MCE on Power9. A CXL fault handling fix, some fixes
to the new XIVE code, and a fix to the new 32-bit STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot but not on
any current machines, a compile error on 4xx and a fix to memory hotplug when
using radix (Power9).
Thanks to:
Anton Blanchard, Cédric Le Goater, Christian Lamparter, Christophe Leroy,
Christophe Lombard, Guenter Roeck, Jeremy Kerr, Michael Neuling, Nicholas
Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=etbe
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Nine small fixes, really nothing that stands out.
A work-around for a spurious MCE on Power9. A CXL fault handling fix,
some fixes to the new XIVE code, and a fix to the new 32-bit
STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot
but not on any current machines, a compile error on 4xx and a fix to
memory hotplug when using radix (Power9).
Thanks to: Anton Blanchard, Cédric Le Goater, Christian Lamparter,
Christophe Leroy, Christophe Lombard, Guenter Roeck, Jeremy Kerr,
Michael Neuling, Nicholas Piggin"
* tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Increase memory block size to 1GB on radix
powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled
powerpc/xive: Clear XIVE internal structures when a CPU is removed
powerpc/xive: Fix IPI reset
powerpc/4xx: Fix compile error with 64K pages on 40x, 44x
powerpc: Fix action argument for cpufeatures-based TLB flush
cxl: Fix memory page not handled
powerpc: Fix workaround for spurious MCE on POWER9
powerpc: Handle MCE on POWER9 with only DSISR bit 30 set
Lorenzo Bianconi
Lukas Wunner
Aastha Gupta
Stefan Brüns
Geert Uytterhoeven
Himanshi Jain
Bartosz Golaszewski
Brian Masney
Michał Mirosław
Harinath Nampally
Quentin Schulz
Ismail H. Kose
Greg Kroah-Hartman
Linus Torvalds
Eugeniy Paltsev