The GPIO block on different QorIQ chips could have registers in different
endianess. Define the property to specify which endian is used by the
hardware.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add the "little-endian" property to fix the issue that eSDHC
is not working and dumping out "mmc0: Controller never released
inhibit bit(s)." error messages constantly.
Fixes: 5461597f6c ("dts/ls2080a: Update DTSI to add support of various peripherals")
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2YO/
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.4-rc4" from Tony Lindgren
Few fixes for omaps for v4.4-rc cycle:
- Fix clock source for ARM TWD and global timers on am437x
- Always select REGULATOR_FIXED_VOLTAGE for omap2+ instead of
when MACH_OMAP3_PANDORA is selected
- Fix SPI DMA handles for dm816x as only some were mapped
- Fix up mbox cells for dm816x to make mailbox usable
* tag 'omap-for-v4.4/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372: fix clock source for arm twd and global timers
ARM: OMAP2+: enable REGULATOR_FIXED_VOLTAGE
ARM: dts: add dm816x missing spi DT dma handles
ARM: dts: add dm816x missing #mbox-cells
The recent change to use a pwm lookup table for the ezx machines
was incomplete and only changed the a780 model, but not the
other ones in the same file.
This adds the missing calls to pwm_add_table().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c332202289 ("ARM: pxa: ezx: Use PWM lookup table")
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJWZLDzAAoJEKbNnwlvZCyzZnsP/0LnaHnd/AQgukmJDHG5L+oY
trhwUctcLxV5T6SMTqkdFJ64im7j9Q9VNs5hFOtm4FiNBUjWNuGGhBIqSUIYIZTp
dRNXs2yIJXXwUl37mQzQPqrt8fKRC2QMgFn2fMLBaPmxOTDgTvZ9aks/DWOCO1Kk
2xZ+7OeyTFZDMEHM7Xb4RpAgAQxaipWfH2+pYoLaPvhPqUDWGrDWdRPNtd/hwvxA
UM4+hGRhcEGdrzDkbC3sno8dvSUH9vwBaHKgLiJ3ZD3atE23w/Xs4HCNtbqtKj/5
Y6LP6067Zr5drb9xt9zV5ghQnoh+u14qcOo4r9F9wwRQs1LYrHiu6T9sntYOhXWN
jLi4fuLF8DVTyDPn0mmd3dVyTe+mDrzk0guJ3B1RkEEgV1/uY7obSFBLyprcPK18
CDq2wEeOuiEaZJrIq6tqHnamKRiq43RcRijx7zs3UlcoUZ7TXCpou/FvPXdoK0OX
8/FOaZueYmK1Hdsit29ibBkrmQ07b+Hajxk10/fWU049hQm5O05rK6XLTQ6doZap
AUbARY7jGcd3uB/TWrYmE0bdAoGhKGOtRVSnWG6qoWdBNzS2q5dJD1m6rPtrNwcj
T2wHei6jRFzc4FOKn9vjOSvbY19LmvkqeWYwlTytcUknqG5hy7Eoo4KGTjo6jGME
jhGnEukaGy7gXoZQAlSv
=Nvkl
-----END PGP SIGNATURE-----
Merge tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into fixes
Merge "Second fixes for 4.4" from Alexandre Belloni:
- fix of a hardware setup that prevents the sd/mmc interface to show up on
sama5d2.
- proper selection of pinctrl drivers. PIO4 is necessary for the sama5d2 to
boot.
* tag 'at91-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: at91: fix pinctrl driver selection
ARM: at91/dt: add always-on to 1.8V regulator
We removed CLK_IGNORE_UNUSED from CLKID_SDIO's flag, so the sdhci0 and
sdhci1 don't work. We fix this by adding the optional 2nd clock for
BG2Q's sdhci0 and sdhci1. This patch brings another benefit: the 2nd
clock can be disabled during runtime pm, so saves power a bit.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The optional 2nd clock is CLKID_SDIO. We removed CLK_IGNORE_UNUSED
from CLKID_SDIO's flag, so the sdhci2 doesn't work. This patch fixes
this issue by correcting the sdhci2's 2nd clock.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
ARM TWD and Global timer are clocked by PERIPHCLK which is MPU_CLK/2.
But now they are clocked by dpll_mpu_m2_ck == MPU_CLK and, as result.
Timekeeping core misbehaves. For example, execution of command
"sleep 5" will take 10 sec instead of 5.
Hence, fix it by adding mpu_periphclk ("fixed-factor-clock") and use
it for clocking ARM TWD and Global timer (same way as on OMAP4).
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Fixes:commit 8cbd4c2f6a ("arm: boot: dts: am4372: add ARM timers and SCU nodes")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since Dove has non-DT support for various facilities in the PMU, convert
the legacy support to use the new PMU driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add support for legacy non-DT Dove to the PMU driver, so that we can
transition the legacy support over.
[gregory.clement@free-electrons.com: removed pm_genpd_poweroff_unused]
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The orion5x platform is now ready to be enabled for multiplatform
support, this patch does the switch over by modifying the Kconfig file,
the defconfig and removing the last mach/*.h header that becomes obsolete
with this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This is a simple move of all header files that are no longer
included by anything else from the include/mach directory
to the platform directory itself as preparation for
multiplatform support.
The mach/uncompress.h headers are left in place for now,
and are mildly modified to be independent of the other
headers. They will be removed entirely when ARCH_MULTIPLATFORM
gets enabled and they become obsolete.
Rather than updating the path names inside of the comments
of each header, I delete those comments to avoid having to
update them again, should they get moved or copied another
time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The mv78xx0 platform is now ready to be enabled for multiplatform
support, this patch does the switch over by modifying the Kconfig file,
the defconfig and removing the last mach/*.h header that becomes obsolete
with this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This is a simple move of all header files that are no longer
included by anything else from the include/mach directory
to the platform directory itself as preparation for
multiplatform support.
The mach/uncompress.h headers are left in place for now,
and are mildly modified to be independent of the other
headers. They will be removed entirely when ARCH_MULTIPLATFORM
gets enabled and they become obsolete.
Rather than updating the path names inside of the comments
of each header, I delete those comments to avoid having to
update them again, should they get moved or copied another
time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As a preparation for multiplatform support, this moves all the
code using plat-orion over to use sparse irq support, which is
enabled implicitly for multiplatform.
In particular, the hardcoded NR_IRQS macro gets replaced with
a machine specific one that is set in the machine descriptor
in order to set up a static mapping for all legacy interrupts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As a preparation for multiplatform support, this enables
the MULTI_IRQ_HANDLER code unconditionally on dove and
orion5x, and introduces the respective code on mv78xx0,
which did not have it so far. The classic entry-macro.S
files are removed as they are now obsolete.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The watchdog device node is created in plat-orion/common.c
but depends on the bridge address that is platform specific,
so as a preparation for orion multiplatform support, we
move it out of the common code into orion5x and dove.
At the moment, dove does not use the watchdog, so I'm marking
the function as __maybe_unused for the moment. The compiler
will be able to compile out the device definition this way,
and we can easily add it later.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Move the selection of the pinctrl driver to SoC family level since we
have two pinctrl drivers. It is useless to select one which is not
compatible with the SoC.
[abelloni: fixed pm.c when only sama2d2 is selected]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
As the SDHCI controller needs the 1.8V line to be always enabled for some eMMC
configurations, set the proper "regulator-always-on" property to the board DTS
files.
Note that the sdhci classical regulator definitions doesn't suit our controller
for this 1.8V purpose.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
So far, only the bus clock has been assigned, but in reality the
SAI IP has for clock inputs. The driver has been updated to
make use of the additional clock inputs by c3ecef21c3 ("ASoC:
fsl_sai: add sai master mode support"). Due to a bug in the
clock tree, the audio clock has been enabled none the less by
the specified bus clock (see "ARM: imx: clk-vf610: fix SAI
clock tree"), which made master mode even without the proper
clock assigned working.
This patch completes the clock definition for SAI2. On Vybrid,
only two MCLK out of the four options are available (the first
being the bus clock itself). See chapter 8.10.1.2.3 of the
Vybrid Reference manual ("SAI transmitter and receiver options
for MCLK selection"). Note: The audio clocks are only required
in master mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Synchronous Audio Interface (SAI) instances are clocked by
independent clocks: The bus clock and the audio clock (as shown in
Figure 51-1 in the Vybrid Reference Manual). The clock gates in
CCGR0/CCGR1 for SAI0 through SAI3 are bus clock gates, as access
tests to the registers with/without gating those clocks have shown.
The audio clock is gated by the SAIx_EN gates in CCM_CSCDR1,
followed by a clock divider (SAIx_DIV). Currently, the parent of
the bus clock gates has been assigned to SAIx_DIV, which is not
involved in the bus clock path for the SAI instances (see chapter
9.10.12, SAI clocking in the Vybrid Reference Manual).
Fix this by define the parent clock of VF610_CLK_SAIx to be the bus
clock.
If the driver needs the audio clock (when used in master mode), a
fixed device tree is required which assign the audio clock properly
to VF610_CLK_SAIx_DIV.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On ixp4xx, the readl() function returns an 'unsigned long' output
when indirect I/O is used. This is unlike any other platform, and
it causes lots of harmless compiler warnings, such as:
drivers/ata/libahci.c: In function 'ahci_show_host_version':
drivers/ata/libahci.c:254:22: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat=]
drivers/block/mtip32xx/mtip32xx.c: In function 'mtip_hw_read_registers':
drivers/block/mtip32xx/mtip32xx.c:2602:31: warning: format '%X' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat=]
drivers/block/cciss.c: In function 'print_cfg_table':
drivers/block/cciss.c:3845:25: warning: format '%d' expects argument of type 'int', but argument 4 has type 'long unsigned int' [-Wformat=]
This changes all six of the ixp4xx specific I/O read functions
to return the same types that we have in the normal asm/io.h,
to avoid the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
This patch is specifically for PCI support on the Versatile PB board using
a DT. Currently, the dynamic IRQ mapping is broken when using DTs. For
example, on QEMU, the SCSI driver is unable to request the IRQ. To fix
this issue, this patch replaces the current dynamic mechanism with a
static value as is done in the non-DT case.
Signed-off-by: Guillaume Delbergue <guillaume.delbergue@greensocs.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Many ARM sub-architectures use prompts followed by "if" conditional,
but it is wrong.
Please notice the difference between
config ARCH_FOO
bool "Foo SoCs" if ARCH_MULTI_V7
and
config ARCH_FOO
bool "Foo SoCs"
depends on ARCH_MULTI_V7
These two are *not* equivalent!
In the former statement, it is not ARCH_FOO, but its prompt that
depends on ARCH_MULTI_V7. So, it is completely valid that ARCH_FOO
is selected by another, but ARCH_MULTI_V7 is still disabled. As it is
not unmet dependency, Kconfig never warns. This is probably not what
you want.
The former should be used only when you need to do so, and you really
understand what you are doing. (In most cases, it should be wrong!)
For enabling/disabling sub-architectures, the latter is always correct.
As a good side effect, this commit fixes some entries over 80 columns
(mach-imx, mach-integrator, mach-mbevu).
[Arnd: I note that there is not really a bug here, according to
the discussion that followed, but I can see value in being consistent
and in making the lines shorter]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Halasa <khc@piap.pl>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The ARM core kernel already calls clocksource_of_init() so why
go to all the trouble of locating and probing this node in the
machine. CLOCKSOURCE_OF_DECLARE() will take care of it in the
clocksource driver, and thus we can also get rid of the
dangling header file <linux/clksrc-dbx500-prcmu.h>
Suggested-by: Arnd Bergmann <arndb@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These three structures are only defined and referenced in
mach-hisi/platsmp.c.
Drop the declarations from the header and add static qualifier
to the definitions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
I could not find any users of this file, past or present, and
it contains only a comment, so let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some header files are never included outside of a mach-w90x900
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some header files are never included outside of a mach-iop13xx
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some header files are never included outside of a mach-davinci
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Some header files are never included outside of a mach-ks8695
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Some header files are never included outside of a mach-omap1
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Lots of header files are never included outside of a mach-pxa
directory and do not need to be made visible in include/mach,
so let's just move them all down one level.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Most of the code for the s3c64xx platform is only used when booting
with ATAGS based board files, but not when using device-tree.
This tries to identify all the s3c64xx specific code that is
unneeded when CONFIG_ATAGS is not set, so we can build a smaller
DT-only kernel if configured that way.
All board support is still left intact but now depends on the
CONFIG_ATAGS symbol that users may intentionally disable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After all preparation work is done, we can finally move the Kconfig
option for s3c64xx into ARCH_MULTIPLATFORM. This implies allowing
SAMSUNG_ATAGS for multiplatform again, but now disallowing the
ADC driver below it, as that still has dependencies on header files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The uart on s3c64xx is essentially the same as on s3c24xx,
so we can share a single assembler file. However, the addresses
are different, and we need to add the respective Kconfig magic
to get the right addresses.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The old ADC and touchscreen drivers are not compatible with
multiplatform support, but we can use the exynos-adc driver
as a replacement.
This changes the common device creation functions for s3c64xx
(but not s3c24xx for now) to use the new driver. To do this,
we have to pass the interrupt resources in the opposite order
and pass the platform data in the adc device node.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds support for the touchscreen on Samsung s3c64xx.
The driver is completely untested but shows roughly how
it could be done, following the example of the at91 driver.
compared to the old plat-samsung/adc driver, there is
no support for prioritizing ts over other clients, nor
for oversampling. From my reading of the code, the
priorities didn't actually have any effect at all, but
the oversampling might be needed.
Verifying this driver is the main issue that is currently
holding up multiplatform support for s3c64xx, so any help
in testing is very much appreciated.
The current version uses the IS_REACHABLE() that is
going to be introduced in the linux-media tree, please
comment this out for testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is another prerequisite for enabling multiplatform
support, and it is the part I am least certain about.
I assume it will cause the extra boot message "Cannot
allocate irq_descs @ IRQ%d, assuming pre-allocated" to
be printed, but otherwise work ok. This definitely needs
to be tested on real hardware to see if it works.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In a multiplatform kernel, each initcall is run regardless
of the platform it is meant for, so it must not attempt to
access SoC-specific registers.
This adds 'if (soc_is_s3c64xx)' to all initcalls that are
specific to the s3c64xx platform, to prevent them from breaking
other platforms once we can build them into a combined kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The gpio-samsung driver is special in the sense that it
interacts directly in multiple ways with the legacy platform
code for the s3c24xx and s3c64xx platforms. In contrast,
all devicetree based machines for Samsung, including the
ones on those two SoC families use a different driver.
The header files that define the interface between the platform
code and the gpio driver are not visible when building a
kernel for ARCH_MULTIPLATFORM, which prevents us from
turning on this option for s3c64xx.
To work around this, we now move the driver back into platform
code, from where it was originally moved to as part of commit
1b39d5f2cc ("gpio/samsung: gpio-samsung.c to support
Samsung GPIOs").
The long-term plan for this driver would be to remove it
entirely, after all Samsung machines have been converted
over to boot from DT, but there is currently no timeline
for when that might happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
As a prerequisite for moving s3c64xx into multiplatform configurations,
we need to change the smartq audio driver to stop using hardcoded
gpio numbers from the header file, and instead pass the gpio data
through platform_data.
In order to do that, we also move the code to use module_platform_driver
and register the platform device using platform_device_register_simple
and register the gpios through the gpiod API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
S3C_ADC is only available on machines that don't do ARCH_MULTIPLATFORM,
so changing the 'select' into 'depends on' here helps us move to
ARCH_MULTIPLATFORM without introducing regressions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
mach-mmp/devices.c:81:21: warning: 'u2o_get' defined but not used [-Wunused-function]
static unsigned int u2o_get(void __iomem *base, unsigned int offset)
^
mach-mmp/devices.c:86:13: warning: 'u2o_set' defined but not used [-Wunused-function]
static void u2o_set(void __iomem *base, unsigned int offset,
^
mach-mmp/devices.c:97:13: warning: 'u2o_clear' defined but not used [-Wunused-function]
static void u2o_clear(void __iomem *base, unsigned int offset,
^
mach-mmp/devices.c:108:13: warning: 'u2o_write' defined but not used [-Wunused-function]
static void u2o_write(void __iomem *base, unsigned int offset,
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With all dependencies taken care of, this enables building
the Marvell mmp platform as part of ARCH_MULTIPLATFORM, along
with other ARMv5 and ARMv7 platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Andrew Lunn <andrew@lunn.ch>
The mach/*.h headers are now inaccessible to any external code,
so we can move them all into the mach-mmp directory itself
and remove the subdirectories.
A few headers are not used at all, so we remove them here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Li Yang
yangbo lu
Stefan Agner
Arnd Bergmann
Jisheng Zhang
Grygorii Strashko
Russell King
Ludovic Desroches
Nicolas Ferre
Guillaume Delbergue
Masahiro Yamada
Linus Walleij