Fix a hard-coded limit of a maximum of 16 cpu's per socket.
The UV Broadcast Assist Unit code initializes by scanning the
cpu topology of the system and assigning a master cpu for each
socket and UV hub. That scan had an assumption of a limit of 16
cpus per socket. With Westmere we are going over that limit.
The UV hub hardware will allow up to 32.
If the scan finds the system has gone over that limit it returns
an error and we print a warning and fall back to doing TLB
shootdowns without the BAU.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org> # .37.x
LKML-Reference: <E1PZol7-0000mM-77@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds code to therm_throt.c to notify core thermal threshold
events. These thresholds are supported by the IA32_THERM_INTERRUPT register.
The status/log for the same is monitored using the IA32_THERM_STATUS register.
The necessary #defines are in msr-index.h. A call back is added to mce.h, to
further notify the thermal stack, about the threshold events.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
LKML-Reference: <D6D887BA8C9DFF48B5233887EF04654105C1251710@bgsmsx502.gar.corp.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Before this patch, the following error would sometimes occur after a
resume on pxa3xx:
/path/to/mm/memory.c:144: bad pmd 8040542e.
The problem was that a temporary page table mapping was being improperly
restored.
The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort. The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0. This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The commit 6ac6b817f3 (ARM: pxa: encode
IRQ number into .nr_irqs) removed definition of ITE_LAST_IRQ which
caused the following build error:
CC arch/arm/common/it8152.o
arch/arm/common/it8152.c: In function 'it8152_init_irq':
arch/arm/common/it8152.c:86: error: 'IT8152_LAST_IRQ' undeclared (first use in this function)
arch/arm/common/it8152.c:86: error: (Each undeclared identifier is reported only once
arch/arm/common/it8152.c:86: error: for each function it appears in.)
make[2]: *** [arch/arm/common/it8152.o] Error 1
Defining the IT8152_LAST_IRQ in the arch/arm/include/hardware/it8152.c
fixes the build.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
MX27_3DS board has a MC13783 PMIC connected to the CSPI2 port.
Add support for the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Disable preemption in init_ibs(). The function only checks the
ibs capabilities and sets up pci devices (if necessary). It runs
only on one cpu but operates with the local APIC and some MSRs,
thus it is better to disable preemption.
[ 7.034377] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/483
[ 7.034385] caller is setup_APIC_eilvt+0x155/0x180
[ 7.034389] Pid: 483, comm: modprobe Not tainted 2.6.37-rc1-20101110+ #1
[ 7.034392] Call Trace:
[ 7.034400] [<ffffffff812a2b72>] debug_smp_processor_id+0xd2/0xf0
[ 7.034404] [<ffffffff8101e985>] setup_APIC_eilvt+0x155/0x180
[ ... ]
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=22812
Reported-by: <atswartz@gmail.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: oprofile-list@lists.sourceforge.net <oprofile-list@lists.sourceforge.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org> [2.6.37.x]
LKML-Reference: <20110103111514.GM4739@erda.amd.com>
[ small cleanups ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Replace the page_to_dma() and dma_to_page() macros with their PFN
equivalents. This allows us to map parts of memory which do not have
a struct page allocated to them to bus addresses. This will be used
internally by dma_alloc_coherent()/dma_alloc_writecombine().
Build tested on Versatile, OMAP1, IOP13xx and KS8695.
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current code doesn't really enable the usb clocks so if they're disabled
when booting linux, the kernel/machine will hang as soon as someone is trying
to read a usb register
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is fixing some issues :
- MXC_OTG_UCTRL_OPM_BIT is for USBCTRL register and not PHYCTRL register.
- the MXC_EHCI_WAKEUP_ENABLED check was only clearing the bits so never allows
to set them.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes below build error by adding the missing asm/memory.h,
which is needed for arch_is_coherent().
$ make pxa3xx_defconfig; make
CC init/do_mounts_rd.o
In file included from include/linux/list_bl.h:5,
from include/linux/rculist_bl.h:7,
from include/linux/dcache.h:7,
from include/linux/fs.h:381,
from init/do_mounts_rd.c:3:
include/linux/bit_spinlock.h: In function 'bit_spin_unlock':
include/linux/bit_spinlock.h:61: error: implicit declaration of function 'arch_is_coherent'
make[1]: *** [init/do_mounts_rd.o] Error 1
make: *** [init] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add basic function and uart device support.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mx5 SoCs have different GPIO port count.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove the following unused funtions:
prom_nodematch()
prom_firstprop()
prom_node_has_property()
Also declare a few local functions static.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the following unused funtions:
prom_stopcpu()
prom_idlecpu()
prom_restartcpu()
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow one shot timer mode to be used with the TWD. This allows
NOHZ mode to be used on SMP systems using the TWD localtimer.
Tested on Versatile Express and U8500.
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
isr_ack is never initialized. So, until the first PIC reset, interrupts
may fail to be injected. This can cause Windows XP to fail to boot, as
reported in the fallout from the fix to
https://bugzilla.kernel.org/show_bug.cgi?id=21962.
Reported-and-tested-by: Nicolas Prochazka <prochazka.nicolas@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Replace all uses of current_cpu_data with this_cpu operations on the
per cpu structure cpu_info. The scala accesses are replaced with the
matching this_cpu ops which results in smaller and more efficient
code.
In the long run, it might be a good idea to remove cpu_data() macro
too and use per_cpu macro directly.
tj: updated description
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Go through x86 code and replace __get_cpu_var and get_cpu_var
instances that refer to a scalar and are not used for address
determinations.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
We use the physical address instead of the base gfn for the four
PAE page directories we use in unpaged mode. When the guest accesses
an address above 1GB that is backed by a large host page, a BUG_ON()
in kvm_mmu_set_gfn() triggers.
Resolves: https://bugzilla.kernel.org/show_bug.cgi?id=21962
Reported-and-tested-by: Nicolas Prochazka <prochazka.nicolas@gmail.com>
KVM-Stable-Tag.
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
spi/pxa2xx: register driver properly
spi/pxa2xx: add support for shared IRQ handler
spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
arm/pxa2xx: reorgazine SSP and SPI header files
spi/pxa2xx: Add CE4100 support
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: pass of_node to spi device and set a parent device
* 'for-grant' of git://arago-project.org/git/projects/linux-davinci into spi/next
spi: davinci: fix checkpatch errors
spi: davinci: whitespace cleanup
spi: davinci: remove unused variable 'pdata'
spi: davinci: set chip-select mode in SPIDEF only once
spi: davinci: enable both activation and deactivation of chip-selects
spi: davinci: remove unnecessary data transmit on CS disable
spi: davinci: enable GPIO lines to be used as chip selects
spi: davinci: simplify prescalar calculation
spi: davinci: remove 'wait_enable' platform data member
spi: davinci: make chip-slect specific parameters really chip-select specific
spi: davinci: consolidate setup of SPIFMTn in one function
spi: davinci: setup chip-select timers values only if timer enabled
spi: davinci: add support for wait enable timeouts
spi: davinci: remove unused members of davinci_spi_slave
spi: davinci: eliminate the single member structure davinci_spi_slave
spi: davinci: eliminate unnecessary update of davinci_spi->count
spi: davinci: simplify calculation of edma acount value
spi: davinci: check for NULL buffer pointer before using it
spi: davinci: remove unnecessary disable of SPI
spi: davinci: remove unnecessary 'count' variable in driver private data
spi: davinci: remove unnecessary completion variable initialization
spi: davinci: remove non-useful interrupt mode support
spi: davinci: simplify poll mode transfers
spi: davinci: add support for interrupt mode
spi: davinci: configure the invariable bits in spipc0 only once
spi: davinci: remove unnecessary function davinci_spi_bufs_prep()
spi: davinci: remove unnecessary call to davinci_spi_setup_transfer()
spi: davinci: do not store DMA channel information per chip select
spi: davinci: always start transmit DMA
spi: davinci: do not use temporary buffer if no transmit data provided
spi: davinci: always start receive DMA
spi: davinci: use edma_write_slot() to setup EDMA PaRAM slot
spi: davinci: fix DMA event generation stoppage
spi: davinci: fix EDMA CC errors at end of transfers
spi: davinci: handle DMA completion errors correctly
spi: davinci: remove usage of additional completion variables for DMA
spi: davinci: let DMA operation be specified on per-device basis
spi: davinci: remove non-useful "clk_internal" platform data
spi: davinci: enable and power-up SPI only when required
spi: davinci: setup the driver owner
spi: davinci: add additional comments
spi: davinci: add EF Johnson Technologies copyright
spi: davinci: removed unused #defines
spi: davinci: remove unnecessary typecast
spi: davinci: do not treat Tx interrupt being set as error
spi: davinci: do not allocate DMA channels during SPI device setup
spi: davinci: remove unnecessary private data member 'region_size'
spi: davinci: shorten variable names
spi: davinci: kconfig: add manufacturer name to prompt string
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/microcode: Fix double vfree() and remove redundant pointer checks before vfree()
arm: export dma_set_coherent_mask
While a regression was fixed with commit 710224fa27 (arm: fix
"arm: fix pci_set_consistent_dma_mask for dmabounce devices"), a
new one was introduced as dma_set_coherent_mask wasn't exported
for modules. This patch takes care for this issue.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
halt() should use native_halt()
safe_halt() uses native_safe_halt()
If CONFIG_PARAVIRT=y, halt() is defined in arch/x86/include/asm/paravirt.h as
static inline void halt(void)
{
PVOP_VCALL0(pv_irq_ops.safe_halt);
}
Otherwise (no CONFIG_PARAVIRT) halt() in arch/x86/include/asm/irqflags.h is
static inline void halt(void)
{
native_halt();
}
So it looks to me like the CONFIG_PARAVIRT case of using native_safe_halt()
for a halt() is an oversight.
Am I missing something?
It probably hasn't shown up as a problem because the local apic is disabled
on a shutdown or restart. But if we disable interrupts and call halt()
we shouldn't expect that the halt() will re-enable interrupts.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
LKML-Reference: <E1PSBcz-0001g1-FM@eag09.americas.sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In arch/x86/kernel/microcode_intel.c::generic_load_microcode()
we have this:
while (leftover) {
...
if (get_ucode_data(mc, ucode_ptr, mc_size) ||
microcode_sanity_check(mc) < 0) {
vfree(mc);
break;
}
...
}
if (mc)
vfree(mc);
This will cause a double free of 'mc'. This patch fixes that by
just removing the vfree() call in the loop since 'mc' will be
freed nicely just after we break out of the loop.
There's also a second change in the patch. I noticed a lot of
checks for pointers being NULL before passing them to vfree().
That's completely redundant since vfree() deals gracefully with
being passed a NULL pointer. Removing the redundant checks
yields a nice size decrease for the object file.
Size before the patch:
text data bss dec hex filename
4578 240 1032 5850 16da arch/x86/kernel/microcode_intel.o
Size after the patch:
text data bss dec hex filename
4489 240 984 5713 1651 arch/x86/kernel/microcode_intel.o
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Shaohua Li <shaohua.li@intel.com>
LKML-Reference: <alpine.LNX.2.00.1012251946100.10759@swampdragon.chaosbits.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
spi/mpc52xx-spi: fix annotation for remove()-pointer
spi/fsl_espi: fix wrong setting of the address in the command buffer
spi/fsl_espi: change the read behaviour of the SPIRF
of/i2c: Fix request module by alias
powerpc/mpc5200: include fs.h in mpc52xx_gpt.c
It appears that arch/arm/mach-omap2/timer-gp.o is needed by OMAP2PLUS.
Since timer-gp.o has direct dependencies on omap_dm_timer_*, it seems
correct for the architecture to depend upon OMAP_DM_TIMER, otherwise
unsuspecting integrators will be faced with a whole bunch of linker
errors at the end of their kernel build:
arch/arm/mach-omap2/built-in.o: In function `omap2_gp_timer_set_mode':
/home/bgamari/trees/linux-2.6/arch/arm/mach-omap2/timer-gp.c:84: undefined reference to `omap_dm_timer_stop'
/home/bgamari/trees/linux-2.6/arch/arm/mach-omap2/timer-gp.c:88: undefined reference to `omap_dm_timer_get_fclk'
/home/bgamari/trees/linux-2.6/arch/arm/mach-omap2/timer-gp.c:90: undefined reference to `omap_dm_timer_set_load_start'
...
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to be fully aligned with the Python generator output,
change a couple of fields.
- Add tab in class structures to align attributes
- Add a comma at the end of the following line to simplify
the generation by having always the same eol:
".pre_shutdown = &omap2_wd_timer_disable,"
- Add a blank line before the first entry of the
omap44xx_hwmods array.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The merge of the DMA series on top of the already modified
omap_hwmod_data_44xx.c put the dma_system structures at
the wrong position in the file.
Re-order it properly.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The merge of the SR series on top of the already modified
omap_hwmod_data_44xx.c moved the smartreflex structures at the wrong
position in the file.
- Re-order the structures properly.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the missing SIDLE_SMART_WKUP flag in idlemodes field of
the smartreflex sysconfig structure.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Thara Gopinath <thara@ti.com>
Tested-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush psw->work on removal instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush toggle_charger and sharpsl_bat works on suspend
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
The current implementation was rather tied to the packed_struct.h
definitions, which immediately began to clash when the packed_struct.h
types changed and drivers began to include packed_struct.h directly.
In order to support this sort of use it's necessary to get out of the way
with regards to namespace collisions, and at the same time we can also
kill off some duplicate code now that the unaligned headers are a bit
more broken out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sev is used to send wakeup event to other cores in ARMv6K and above.
This has been moved from platform specific part to standard common
ARM header file (asm/system.h). Also introduced wfi() and wfe().
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows platforms to hook into the initialization early to setup
things like scheduler clocks, etc.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than storing each machine init hook separately, store a
pointer to the machine description record and dereference this
instead. This pointer is only available while the init sections
are present, which is not a problem as we only use it from init
code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Per subarch interrupt handler macros V3.
This patch breaks out code from the irq_handler macro
into arch_irq_handler and arch_irq_handler_default.
The macros are put in the header file "entry-macro-multi.S"
The arch_irq_handler_default macro is designed to be
used by irq_handler in entry-armv.S while arch_irq_handler
is suitable for per-subarch use.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Normally different ARM platform has different way to decode the IRQ
hardware status and demultiplex to the corresponding IRQ handler.
This is highly optimized by macro irq_handler in entry-armv.S, and
each machine defines their own macro to decode the IRQ number.
However, this prevents multiple machine classes to be built into a
single kernel.
By allowing each machine to specify thier own handler, and making
function pointer 'handle_arch_irq' to point to it at run time, this
can be solved. And introduce CONFIG_MULTI_IRQ_HANDLER to allow both
solutions to work.
Comparing with the highly optimized macro of irq_handler, the new
function must be written with care not to lose too much performance.
And the IPI stuff on SMP is expected to move to the provided arch
IRQ handler as well.
The assembly code to invoke handle_arch_irq is optimized by Russell
King.
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the irqsoff tracer is in use, stop tracing the interrupt disable
interval when returning to userspace. Tracing userspace execution time
as interrupts disabled time is not helpful for kernel performance
analysis purposes. Only do so if the irqsoff tracer is enabled, to
avoid overhead for lockdep, which doesn't care.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... and also remove misleading comment stating that this header is
auto-generated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The master clock initialization for SH7201 was wholly bogus. Users of the
legacy API must initialize the clock rate through the struct clk itself
rather than returning the clock frequency. Given that the init function
itself is void, returning the frequency isn't terribly effective.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With some recent tidying of duplicate register definitions the se7206 IRQ
code broke:
arch/sh/boards/mach-se/7206/irq.c: error: 'INTC_ICR' undeclared (first use in this function)
arch/sh/boards/mach-se/7206/irq.c: error: (Each undeclared identifier is reported only once
arch/sh/boards/mach-se/7206/irq.c: error: for each function it appears in.)
Fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some of the SH4-202 code was overlooked in the set_rate() API conversion,
resulting in:
arch/sh/kernel/cpu/sh4/clock-sh4-202.c: error: too many arguments to function 'clk->ops->set_rate'
Fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix to support libdwfl older than 0.148
perf tools: Fix lazy wildcard matching
perf buildid-list: Fix error return for success
perf buildid-cache: Fix symbolic link handling
perf symbols: Stop using vmlinux files with no symbols
perf probe: Fix use of kernel image path given by 'k' option
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, kexec: Limit the crashkernel address appropriately
Recent Intel new system have different order in MADT, aka will list all thread0
at first, then all thread1.
But SRAT table still old order, it will list cpus in one socket all together.
If the user have compiled limited NR_CPUS or boot with nr_cpus=, could have missed
to put some cpus apic id to node mapping into apicid_to_node[].
for example for 4 sockets system with 64 cpus with nr_cpus=32 will get crash...
[ 9.106288] Total of 32 processors activated (136190.88 BogoMIPS).
[ 9.235021] divide error: 0000 [#1] SMP
[ 9.235315] last sysfs file:
[ 9.235481] CPU 1
[ 9.235592] Modules linked in:
[ 9.245398]
[ 9.245478] Pid: 2, comm: kthreadd Not tainted 2.6.37-rc1-tip-yh-01782-ge92ef79-dirty #274 /Sun Fire x4800
[ 9.265415] RIP: 0010:[<ffffffff81075a8f>] [<ffffffff81075a8f>] select_task_rq_fair+0x4f0/0x623
...
[ 9.645938] RIP [<ffffffff81075a8f>] select_task_rq_fair+0x4f0/0x623
[ 9.665356] RSP <ffff88103f8d1c40>
[ 9.665568] ---[ end trace 2296156d35fdfc87 ]---
So let just parse all cpu entries in SRAT.
Also add apicid checking with MAX_LOCAL_APIC, in case We could out of boundaries of
apicid_to_node[].
it fixes following bug too.
https://bugzilla.kernel.org/show_bug.cgi?id=22662
-v2: expand to 32bit according to hpa
need to add MAX_LOCAL_APIC for 32bit
Reported-and-Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Reported-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Tested-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD486.9020704@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We should use MAX_LOCAL_APIC for max apic ids and MAX_APICS as number
of local apics.
Also apic_version[] array should use MAX_LOCAL_APICs.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD464.2020408@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
commit fcf173e451
(add names for IRQs in structure resource)
forgot to take care of tusb6010 making it
fail to probe due to a missing resource.
Fix it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517/05 Craneboard has one EHCI interface on board using port1.
GPIO35 is used as power enable.
GPIO38 is used as port1 PHY reset.
History:
http://marc.info/?l=linux-omap&w=2&r=1&s=Craneboard%253A%2BAdd%2BUSB%2BEHCI%2Bsupport&q=b
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix build errors like these (from a randconfig and my defconfig for a custom board):
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:549: error: dereferencing pointer to incomplete type: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:636: error: implicit declaration of function 'nonseekable_open': 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:657: error: variable 'mpc52xx_wdt_fops' has initializer but incomplete type: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:658: error: excess elements in struct initializer: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:658: error: unknown field 'owner' specified in initializer: 1 errors in 1 logs
...
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use omap_serial_init_port so we can let the serial code handle the
remuxing of the RX pads. Note that this patch alone is not enough
and additional GPIO related patches are needed.
Only initialize uart3_rx_irrx pin, the other uart pins can be
stay static.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow hwmod state changes to mux pads based on the state changes.
By default, only enable and disable the pads. In some rare cases
dynamic remuxing for the idles states is needed, this can be done
by passing the enable, idle, and off pads from board-*.c file along
with OMAP_DEVICE_PAD_REMUX flag.
Thanks to Paul Walmsley <paul@booyaka.com> for the comments on the
hwmod related changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows adding hwmod specific pads dynamically during the
platform device init.
Note that we don't currently have the hwmod specific signals
listed in the hwmod data, but struct omap_hwmod_mux_info will
make that possible if necessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do this by splitting _omap_mux_init_signal as it already has most
of the necessary features.
Based on an earlier patch by Dan Murphy <dmurphy@ti.com>.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When CONFIG_SUSPEND is not enabled, none of the system PM methods are
used, so do not compile them in.
Thanks to Charles Manning for reporting the problem and proposing
an initial patch.
Reported-by: Charles Manning <manningc2@actrix.gen.nz>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert versatile platforms to use the new sched_clock() infrastructure
for extending 32bit counters to full 64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert orion platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert omap to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert nomadik platforms to use the new sched_clock() infrastructure
for extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert iop platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert u300 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert tegra to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert sa1100 to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert pxa to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert mmp to use the new sched_clock() infrastructure for extending
32bit counters to full 64-bit nanoseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert ixp4xx to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide common sched_clock() infrastructure for platforms to use to
create a 64-bit ns based sched_clock() implementation from a counter
running at a non-variable clock rate.
This implementation is based upon maintaining an epoch for the counter
and an epoch for the nanosecond time. When we desire a sched_clock()
time, we calculate the number of counter ticks since the last epoch
update, convert this to nanoseconds and add to the epoch nanoseconds.
We regularly refresh these epochs within the counter wrap interval.
We perform a similar calculation as above, and store the new epochs.
We read and write the epochs in such a way that sched_clock() can easily
(and locklessly) detect when an update is in progress, and repeat the
loading of these constants when they're known not to be stable. The
one caveat is that sched_clock() is not called in the middle of an
update. We achieve that by disabling IRQs.
Finally, if the clock rate is known at compile time, the counter to ns
conversion factors can be specified, allowing sched_clock() to be tightly
optimized. We ensure that these factors are correct by providing an
initialization function which performs a run-time check.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
tegra_clocksource_read should not use cnt32_to_63, wrapping is
already handled in the clocksource code. Move the cnt32_to_63
into the sched_clock function, and replace the use of clocksource
mult and shift with a multiplication by 1000 to convert us to ns.
Acked-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Wan zongshun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-By: Jeff Ohlstein <johlstei@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-By: Scott Branden <sbranden@broadcom.com>
Acked-By: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch extends the smartreflex framework to support
OMAP4. The changes are minor like compiling smartreflex Kconfig
option for OMAP4 also, and a couple of OMAP4 checks in
the smartreflex framework.
The change in sr_device.c where new logic has to be introduced
for reading the efuse registers is due to the fact that in OMAP4
the efuse registers are 24 bit aligned. A __raw_readl will
fail for non-32 bit aligned address and hence the 8-bit read
and shift.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the hwmod details for OMAP4 smartreflex modules.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default the system boots up at nominal voltage for every
voltage domain in the system. This patch puts vdd_mpu, vdd_iva
and vdd_core to the correct boot up voltage as per the opp tables
specified. This patch implements this by matching the rate of
the main clock of the voltage domain with the opp table and
picking up the correct voltage.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 has three scalable voltage domains vdd_mpu, vdd_iva
and vdd_core. This patch adds the voltage tables and other
configurable voltage processor and voltage controller
settings to control these three scalable domains in OMAP4.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
TWL6030 is the power IC used along with OMAP4 in OMAP4 SDPs,
blaze boards and panda boards. This patch registers the OMAP4
PMIC specific information with the voltage layer.
This also involves implementing a different formula for
voltage to vsel and vsel to voltage calculations from
TWL4030.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default the system boots up at nominal voltage for every
voltage domain in the system. This patch puts VDD1 and VDD2
to the correct boot up voltage as per the opp tables specified.
This patch implements this by matching the rate of the main clock
of the voltage domain with the opp table and picking up the correct
voltage.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds debug support to the voltage and smartreflex drivers.
This means a whole bunch of voltage processor and smartreflex
parameters are now visible through the pm debugfs.
The voltage parameters can be viewed at
/debug/voltage/vdd_<x>/<parameter>
and the smartreflex parameters can be viewed at
/debug/voltage/vdd_<x>/smartreflex/<parameter>
Also smartreflex n-target values are now exposed out at
/debug/voltage/vdd_<x>/smartreflex/nvalue/<voltage>
This is a read-write interface which means user has the
flexibility to change the n-target values for any opp.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch registers the TWL4030 PMIC specific informtion
with the voltage driver. Failing this patch the voltage driver
is unware of the formula to use for vsel to voltage and vice versa
conversion and lot of other PMIC dependent parameters.
This file is based on the arch/arm/plat-omap opp_twl_tpl.c file
by Paul Walmsley. The original file is replaced by this file.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Smartreflex Class3 implementation continuously monitors
silicon performance and instructs the Voltage Processors
to increase or decrease the voltage.
This patch adds smartreflex class 3 driver. This driver hooks
up with the generic smartreflex driver smartreflex.c to abstract
out class specific implementations out of the generic driver.
Class3 driver is chosen as the default class driver for smartreflex.
If any other class driver needs to be implemented, the init of that
driver should be called from the board file. That way the new class driver
will over-ride the Class3 driver.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the smartreflex hwmod data for OMAP3430
and OMAP3630.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for device registration of various
smartreflex module present in the system. This patch introduces
the platform data for smartreflex devices which include
the efused n-target vaules, a parameter to indicate
whether smartreflex autocompensation needs to be
enabled on init or not. An API
omap_enable_smartreflex_on_init is provided for the
board files to enable smartreflex autocompensation during
system boot up.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
SmartReflex modules do adaptive voltage control for real-time
voltage adjustments. With Smartreflex the power supply voltage
can be adapted to the silicon performance(manufacturing process,
temperature induced performance, age induced performance etc).
There are differnet classes of smartreflex implementation.
Class-0: Manufacturing Test Calibration
Class-1: Boot-Time Software Calibration
Class-2: Continuous Software Calibration
Class-3: Continuous Hardware Calibration
Class-4: Fully Integrated Power Management
OMAP3 has two smartreflex modules one associated with VDD MPU and the
other associated with VDD CORE.
This patch adds support for smartreflex driver. The driver is designed
for Class-1 , Class-2 and Class-3 support and is a platform driver.
Smartreflex driver can be enabled through a Kconfig option
"SmartReflex support" under "System type"->"TI OMAP implementations" menu.
Smartreflex autocompensation feature can be enabled runtime through
a debug fs option.
To enable smartreflex autocompensation feature
echo 1 > /debug/voltage/vdd_<X>/smartreflex/autocomp
To disable smartreflex autocompensation feature
echo 0 > /debug/voltage/vdd_<X>/smartreflex/autocomp
where X can be mpu, core , iva etc.
This patch contains code originally in linux omap pm branch.
Major contributors to this driver are
Lesly A M, Rajendra Nayak, Kalle Jokiniemi, Paul Walmsley,
Nishant Menon, Kevin Hilman.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch extends the device hwmod structure to contain
info about the voltage domain to which the device belongs to.
This is needed to support a device based DVFS where the
device knows which voltage domain it belongs to.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds voltage driver support for OMAP3. The driver
allows configuring the voltage controller and voltage
processors during init and exports APIs to enable/disable
voltage processors, scale voltage and reset voltage.
The driver maintains the global voltage table on a per
VDD basis which contains the various voltages supported by the
VDD along with per voltage dependent data like smartreflex
efuse offset, errminlimit and voltage processor errorgain.
The driver also allows the voltage parameters dependent on the
PMIC to be passed from the PMIC file through an API.
The driver allows scaling of VDD voltages either through
"vc bypass method" or through "vp forceupdate method" the
choice being configurable through the board file.
This patch contains code originally in linux omap pm branch
smartreflex driver. Major contributors to this driver are
Lesly A M, Rajendra Nayak, Kalle Jokiniemi, Paul Walmsley,
Nishant Menon, Kevin Hilman. The separation of PMIC parameters
into a separate structure which can be populated from
the PMIC file is based on the work of Lun Chang from Motorola
in an internal tree.
Signed-off-by: Thara Gopinath <thara@ti.com>
[khilman: fixed link error for OMAP2-only defconfig]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The x86 arch has shifted its use of the nmi_watchdog from a
local implementation to the global one provide by
kernel/watchdog.c. This shift has caused a whole bunch of
compile problems under different config options. I attempt to
simplify things with the patch below.
In order to simplify things, I had to come to terms with the
meaning of two terms ARCH_HAS_NMI_WATCHDOG and
CONFIG_HARDLOCKUP_DETECTOR. Basically they mean the same thing,
the former on a local level and the latter on a global level.
With the old x86 nmi watchdog gone, there is no need to rely on
defining the ARCH_HAS_NMI_WATCHDOG variable because it doesn't
make sense any more. x86 will now use the global
implementation.
The changes below do a few things. First it changes the few
places that relied on ARCH_HAS_NMI_WATCHDOG to use
CONFIG_X86_LOCAL_APIC (the former was an alias for the latter
anyway, so nothing unusual here). Those pieces of code were
relying more on local apic functionality the nmi watchdog
functionality, so the change should make sense.
Second, I removed the x86 implementation of
touch_nmi_watchdog(). It isn't need now, instead x86 will rely
on kernel/watchdog.c's implementation.
Third, I removed the #define ARCH_HAS_NMI_WATCHDOG itself from
x86. And tweaked the include/linux/nmi.h file to tell users to
look for an externally defined touch_nmi_watchdog in the case of
ARCH_HAS_NMI_WATCHDOG _or_ CONFIG_HARDLOCKUP_DETECTOR. This
changes removes some of the ugliness in that file.
Finally, I added a Kconfig dependency for
CONFIG_HARDLOCKUP_DETECTOR that said you can't have
ARCH_HAS_NMI_WATCHDOG _and_ CONFIG_HARDLOCKUP_DETECTOR. You can
only have one nmi_watchdog.
Tested with
ARCH=i386: allnoconfig, defconfig, allyesconfig, (various broken
configs) ARCH=x86_64: allnoconfig, defconfig, allyesconfig,
(various broken configs)
Hopefully, after this patch I won't get any more compile broken
emails. :-)
v3:
changed a couple of 'linux/nmi.h' -> 'asm/nmi.h' to pick-up correct function
prototypes when CONFIG_HARDLOCKUP_DETECTOR is not set.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
LKML-Reference: <1293044403-14117-1-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is to resolve the conflict in the file,
drivers/usb/gadget/composite.c that was due to a revert in Linus's tree
needed for the 2.6.37 release.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Apart from the regular AM18x/DA850/OMAP-L138 SoC operating
at 300MHz, these SoCs have variants that can operate at a
maximum of 456MHz. Variants at 408Mhz and 375 Mhz are available
as well.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
The EVM hardware for all these variants is the same (except
for the actual SoC populated).
U-Boot on the EVM sets up ATAG_REVISION to inform the OS
regarding the speed grade supported by the silicon. We use
this information to pass on the speed grade information to
the SoC code.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
AM18x/DA850/OMAP-L138 SoCs have variants that can operate
at a maximum of 456 MHz at 1.3V operating point. Also the
1.2V operating point has a variant that can support a maximum
of 375 MHz.
This patch adds three new OPPs (456 MHz, 408 MHz and 372 MHz)
to the list of DA850 OPPs.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
Because of this, we depend on the maximum speed grade information
to be provided to us in some board specific way. The board informs
the maximum speed grade information by setting the da850_max_speed
variable.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use the mach-davinci/Kconfig to enable gpio-keys-polled as default when
da850-evm machine is enabled.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: "Nori, Sekhar" <nsekhar@ti.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a pca953x platform device for the tca6416 found on the evm
baseboard. The tca6416 is a GPIO expander, also found on the UI board at a
separate I2C address. The pins of the baseboard IO expander are connected to
software reset, deep sleep enable, test points, a push button, DIP switches and
LEDs.
Add support for the push button, DIP switches and LEDs and test points (as
free GPIOs). The reset and deep sleep enable connections are reserved by the
setup routine so that userspace can't toggle those lines.
The existing tca6416-keypad driver was not employed because there was no
apararent way to register the LEDs connected to gpio's on the tca6416 while
simultaneously registering the tca6416-keypad instance.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The setup and teardown methods of the UI expander reference the SEL_{A,B,C}
pins by 'magic number' in each function. This uses the common enum for their offsets
in the expander setup and teardown functions.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Victor Rodriguez <vm.rod25@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds EV_KEYs for each of the 8 pushbuttons on the UI board via a
gpio-key device.
The expander is a tca6416; it controls the SEL_{A,B,C} lines which enable and
disable the peripherals found on the UI board in addition to the 8 pushbuttons
mentioned above. The reason the existing tca6416-keypad driver is not employed
is because there was no aparent way to keep the gpio lines used as
SEL_{A,B,C} registered while simultaneously registering the pushbuttons as a
tca6416-keypad instance.
Some experimentation with the polling interval was performed; we were searching
for the largest polling interval that did not affect the feel of the
responsiveness of the buttons. It is very subjective but 200ms seems to be a
good value that accepts firm pushes but rejects very light ones. The key values
assigned to the buttons were arbitrarily chosen to be F1-F8.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Most keypad drivers make use of the <linux/input/matrix_keypad.h>
defined macros, structures and inline functions.
Convert omap-keypad driver to use those as well, as suggested by a
compile time warning, hardcoded into the OMAP <palt/keypad.h>.
Created against linux-2.6.37-rc5.
Tested on Amstrad Delta.
Compile tested with omap1_defconfig and omap2plus_defconfig shrinked to
board-h4.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3_IVA_MASK should use OMAP3_IVA_SHIFT instead of OMAP3_SGX_SHIFT
Signed-off-by: Arno Steffen <arno.steffen@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 60d24ee "Added video data to support tvout on rx51" added code that
tries to assign gpio 40 as OMAP DSS reset_gpio for tvout. This is wrong
since this gpio has nothing to do with OMAP DSS but it is used to control
one switch that selects is the audio jack connected to tvout or audio
circuitry.
This switch is already supported by the RX51 ASoC driver so there is no need
to control it elsewhere. Switch is contolled with ALSA control
'Jack Function' and tvout can be selected with following example:
amixer -D hw:0 set 'Jack Function' 'TV-OUT'
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commmit 60d24ee "Added video data to support tvout on rx51" broke the DSS
on RX51/N900 since it added DSS VENC support but a patch adding needed
supply is missing from tree and no framebuffers are initialized.
This patch is basically cleaned up version of original one:
http://marc.info/?l=linux-omap&m=129070041402418&w=2
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It is much more cleaner to use REGULATOR_SUPPLY macro and a device name
instead of having a reference to rx51_display_device.dev with #if defined()
guards.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The following OMAP4 clocks have the following fixed divisors that
determine the frequency at which these clocks operate. These
dividers are defined by the PRCM specification and without these
dividers the rates of the below clocks are calculated incorrectly.
This may cause internal peripherals using these clocks to operate
at the wrong frequency.
- abe_24m_fclk (freq = divided-by-8)
- ddrphy_ck (freq = parent divided-by-2)
- dll_clk_div_ck (freq = parent divided-by-2)
- per_hs_clk_div_ck (freq = parent divided-by-2)
- usb_hs_clk_div_ck (freq = parent divided-by-3)
- func_12m_fclk (freq = parent divided-by-16)
- func_24m_clk (freq = parent divided-by-4)
- func_24mc_fclk (freq = parent divided-by-8)
- func_48mc_fclk (freq = divided-by-4)
- lp_clk_div_ck (freq = divided-by-16)
- per_abe_24m_fclk (freq = divided-by-4)
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch adds comments on precaution to be taken if Global Warm reset is
used as the means to trigger system reset.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: fixed typos, one mentioned by Sanjeev]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
UV systems can be partitioned into multiple independent SSIs.
Large partitioned systems may have extra bits in the node_id
register. These bits are used when the total memory on all SSIs
exceeds 16TB. These extra bits need to be ignored when
calculating x2apic_extra_bits.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101130195926.972776133@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Early in boot, reading MMRs from the UV hub controller require
calls to early_ioremap()/early_iounmap(). Rather than
duplicating code, add a common function to do the
map/read/unmap.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20101130195926.834804371@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The hardware page tables use an XN bit 'execute never'. Historically,
we've had a Linux 'execute allow' bit, in the positive sense. Get rid
of this artifact as future hardware will continue to have the XN sense.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
FIRST_USER_PGD_NR is now unnecessary, as this has been replaced by
FIRST_USER_ADDRESS except in the architecture code. Fix up the last
usage of FIRST_USER_PGD_NR, and remove the definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove some knowledge of our 2-level page table layout from the
identity mapping code - we assume that a step size of PGDIR_SIZE will
allow us to step over all entries. While this is true today, it won't
be true in the near future.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have two places where we create identity mappings - one when we bring
secondary CPUs online, and one where we setup some mappings for soft-
reboot. Combine these two into a single implementation. Also collect
the identity mapping deletion function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMU is always configured to read page tables from the L2 cache
so there's little point flushing them out of the L2 cache back to
RAM. Remove these flushes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches the ordering of the Linux vs hardware page tables in
each page, thereby eliminating some of the arithmetic in the page
table walks. As we now place the Linux page table at the beginning
of the page, we can deal with the offset in the pgt by simply masking
it away, along with the other control bits.
This also makes the arithmetic all be positive, rather than a mixture.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Suffix the U5500 modem IRQ and MBOX files with *-db5500* so that
we clearly know the SoC they belong to, in line with the rest of
the files in mach-ux500.
Cc: Stefan Nilsson <stefan.xk.nilsson@stericsson.com>
Cc: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Follow up to pfc-sh73a0.c's pull-up support.
Change GPIO_FN_KEYINx to GPIO_FN_KEYINx_PU.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On SH-Mobile, Pull UP/Downs can be controlled independently
from Function selectors (by lower nibble of PFCR).
It means people may want to use GPIO_FN_xxx_PU/PD in addition
to GPIO_IN_PU/PD which is currently supported.
This patch adds pull-up version for some input signals on
KEYSC, MMC, FSIA as well as SDHI1.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the sh73a0 KEYSC clock control by adding MSTP403
to mstp_clks[]. Use KEYSC instead of KEYSC0 in comments.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
L3INSTR clock domain is read only register and its reset value is
HW_AUTO. The modules withing this clock domain needs to be kept under
hardware control.
MODULEMODE:
- 0x0: Module is disable by software. Any INTRCONN access to module
results in an error, except if resulting from a module wakeup
(asynchronous wakeup).
- 0x1: Module is managed automatically by hardware according to
clock domain transition. A clock domain sleep transition put
module into idle. A wakeup domain transition put it back
into function. If CLKTRCTRL=3, any INTRCONN access to module
is always granted. Module clocks may be gated according to
the clock domain state.
This patch keeps CM_L3INSTR_L3_3_CLKCTRL, CM_L3INSTR_L3_INSTR_CLKCTRL
and CM_L3INSTR_INTRCONN_WP1_CLKCTRL module mode under hardware control
by using ENABLE_ON_INIT flag.
Without this the OMAP4 device OFF mode SAR restore phase aborts during
interconnect register restore phase. This can be also handled by doing
explicit a clock enable and disable in the low power code since there
is no direct module associated with it. But that seems not necessary
since the clock domain is under HW control.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, there is an issue when L3INIT transitions to OFF mode without
device OFF. The SAR restore mechanism will not get triggered without
wakeup from device OFF and hence the USB host and USB TLL context
will not be restored.
Hardware team recommended to remove the OFF state support for L3INIT_PD
since there is no power impact. It will be removed on next OMAP revision
(OMAP4440 and beyond).
Hence this patch removed the OFF state from L3INIT_PD. The deepest
state supported on L3INIT_PD is OSWR just like CORE_PD and PER_PD
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[b-cousson@ti.com: update the changelog with next OMAP info]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The l4per power domain in ES2.0 does support only RET and ON states.
The previous ES1.0 HW database was wrong and thus fixed on ES2.
Change the pwrsts field to reflect that.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
omap_set_pwrdm_state today assumes a clkdm supports hw_auto
transitions and hence leaves some which do not support this
in sw wkup state preventing low power transitions.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For pwrdm's which support LOWPOWERSTATECHANGE, do not try waking
up the domain to put it back to deeper sleep state.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add support for 2 TMU timer channels on sh73a0.
One timer channel is used for clocksource and
the other is used for clockevents. All channels
in the same TMU block share MSTP bit as usual.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add INTCS support for the sh73a0 processor.
The interrupts on the sh73a0 processor are managed
through controllers such as GIC, INTCS and INTCA.
The ARM cores use the GIC as primary interrupt
controller and the INTCS and INTCA are hanging off
the GIC as cascaded interrupt controllers.
Peripherals connected both to the GIC and the INTC
controllers should if possible only use the GIC.
If no GIC connection is available then INTCS and
INTCA may be used instead.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For devices which have not (yet) been converted to use omap_device,
implement the context loss counter using the "brutal method" as
originally proposed by Paul Walmsley[1].
The dummy context loss counter is incremented every time it is
checked, but only when off-mode is enabled. When off-mode is
disabled, the dummy counter stops incrementing.
Tested on 36xx/Zoom3 using MMC driver, which is currently the
only in-tree user of this API.
This patch should be reverted after all devices are converted to using
omap_device.
[1] http://marc.info/?l=linux-omap&m=129176260000626&w=2
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: fixed compile warning; fixed to compile on OMAP1]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Implement OMAP PM layer omap_pm_get_dev_context_loss_count() API by
creating similar APIs at the omap_device and omap_hwmod levels. The
omap_hwmod level call is the layer with access to the powerdomain
core, so it is the place where the powerdomain is queried to get the
context loss count.
The new APIs return an unsigned value that can wrap as the
context-loss count grows. However, the wrapping is not important as
the role of this function is to determine context loss by checking for
any difference in subsequent calls to this function.
Note that these APIs at each level can return zero when no context
loss is detected, or on errors. This is to avoid returning error
codes which could potentially be mistaken for large context loss
counters.
NOTE: only works for devices which have been converted to use
omap_device/omap_hwmod.
Longer term, we could possibly remove this API from the OMAP PM layer,
and instead directly use the omap_device level API.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add new powerdomain API
u32 pwrdm_get_context_loss_count(struct powerdomain *pwrdm)
for checking how many times the powerdomain has lost context. The
loss count is the sum of the powerdomain off-mode counter, the
logic off counter and the per-bank memory off counter.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: removed bogus return value on error; improved kerneldoc;
tweaked commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In omap4, there is no explicit configuration register to enable mailbox clocks.
Defining dummy clock for mailbox clock module to keep the mailbox driver
backward compatible with previous omaps.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
J-Type DPLLs have additional configuration parameters that need to
be programmed when setting the multipler and divider for the DPLL.
These parameters being the sigma delta divider (SD_DIV) for the DPLL
and the digital controlled oscillator (DCO) to be used by the DPLL.
The current code is implemented specifically to configure the
OMAP3630 PER J-Type DPLL. The OMAP4430 USB DPLL is also a J-Type DPLL
and so this code needs to be updated to work for both OMAP3 and OMAP4
devices and any other future devices that have J-TYPE DPLLs.
For the OMAP3630 PER DPLL both the SD_DIV and DCO paramenters are
used but for the OMAP4430 USB DPLL only the SD_DIV field is used.
The current implementation will only program the SD_DIV and DCO
fields if the DPLL has both and hence this does not work for
OMAP4430.
In order to make the code more generic add two new fields to the
dpll_data structure for the SD_DIV field and DCO field bit-masks
and only program these fields if the masks are defined for a specific
DPLL. This simplifies the code and allows us to remove the flag
DPLL_NO_DCO_SEL.
Tested on OMAP36xx Zoom3 and OMAP4 Blaze.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: removed explicit inlining and added '_' prefix on lookup_*()
functions; added testing info to commit message; added 35xx comments back in]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update clock3xxx_data for mcspi1-4 with appropriate clock domain name.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
uart, gpio, wd_timer and i2c does support the new smart-idle with wakeup
added in OMAP4.
Add the flag to allow the hwmod core to enable this mode when applicable.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The new OMAP4 IPs introduced a new idle mode named smart-idle with wakeup.
This new idlemode replaces the enawakeup for the new IPs but seems to
coexist as well for some legacy IPs (UART, GPIO, MCSPI...)
Add the new SIDLE_SMART_WKUP flag to mark the IPs that support this
capability.
The omap_hwmod_44xx_data.c will have to be updated to add this new flag.
Enable this new mode when applicable in _enable_wakeup, _enable_sysc and
_idle_sysc.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
In cases where a module (hwmod) does not become accesible on enabling
the main clocks (can happen if there are external clocks needed
for the module to become accesible), make sure the clocks are not
left enabled.
This ensures that when the requisite external dependencies are met
a omap_hwmod_enable and omap_hwmod_idle/shutdown would rightly enable
and disable clocks using clk framework. Leaving the clocks enabled in
the error case causes additional usecounting at the clock framework
level leaving the clock enabled forever.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The hwmod list will be built are init time and never
be modified at runtime. There is no need anymore to protect
the list from concurrent accesses using a mutex.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
_register, _find_mpu_port_index and _find_mpu_rt_base are static APIs
that will be used only during the omap_hwmod initialization phase.
There is no need to keep them for runtime.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Do not allow omap_hwmod_register to be used outside the core
hwmod code. An omap_hwmod should be registered only at init time.
Remove the omap_hwmod_unregister that is not used today since the
hwmod list will be built once at init time and never be modified
at runtime.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Since i2c1 and i2c2 are using the same data, remove the two previous
instances and use a common i2c_dev_attr one.
Moreover, that will fix the following warning:
arch/arm/mach-omap2/omap_hwmod_2430_data.c:485:
warning: 'i2c_dev_attr' defined but not used
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Charulatha V <charu@ti.com>
In the omap_hwmod core, most of the SYSCONFIG register helper
functions do not directly write the register, but instead just modify
a value passed in.
This patch converts the _enable_wakeup() and _disable_wakeup() helper
functions to take a value argument and only modify it instead of
actually writing the register. This makes the wakeup helpers
consistent with the other helper functions and avoids unintentional
problems like the following.
This problem was found after discovering that GPIO wakeups were no
longer functional. The root cause was that the ENAWAKEUP bit of the
SYSCONFIG register was being unintentionaly overwritten, leaving
wakeups disabled after the following two commits were combined:
commit: 9980ce53c9
OMAP: hwmod: Enable module wakeup if in smartidle
commit: 78f26e872f
OMAP: hwmod: Set autoidle after smartidle during _sysc_enable
There resulting in code in _enable_sysc() was this:
/*
* XXX The clock framework should handle this, by
* calling into this code. But this must wait until the
* clock structures are tagged with omap_hwmod entries
*/
if ((oh->flags & HWMOD_SET_DEFAULT_CLOCKACT) &&
(sf & SYSC_HAS_CLOCKACTIVITY))
_set_clockactivity(oh, oh->class->sysc->clockact, &v);
_write_sysconfig(v, oh);
so here, 'v' has wakeups disabled.
/* If slave is in SMARTIDLE, also enable wakeup */
if ((sf & SYSC_HAS_SIDLEMODE) && !(oh->flags & HWMOD_SWSUP_SIDLE))
_enable_wakeup(oh);
Here wakeup is enabled in the SYSCONFIG register (but 'v' is not updated)
/*
* Set the autoidle bit only after setting the smartidle bit
* Setting this will not have any impact on the other modules.
*/
if (sf & SYSC_HAS_AUTOIDLE) {
idlemode = (oh->flags & HWMOD_NO_OCP_AUTOIDLE) ?
0 : 1;
_set_module_autoidle(oh, idlemode, &v);
_write_sysconfig(v, oh);
}
And here, SYSCONFIG is updated again using 'v', which does not have
wakeups enabled, resulting in ENAWAKEUP being cleared.
Special thanks to Benoit Cousson for pointing out that wakeups were
supposed to be automatically enabled when a hwmod is enabled, and thus
helping target the root cause of this problem.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fix opt clocks name in clock framework and hwmod.
Add the missing iclk in the ocp_if structure.
Add the HWMOD_CONTROL_OPT_CLKS_IN_RESET flag to ensure
the the GPIO optional clock is enable during reset.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Charulatha V <charu@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Add IVA and DSP hwmods in order to allow the pm code to
initialize properly the processors devices during
omap2_init_processor_devices.
It will avoid the following warnings.
_init_omap_device: could not find omap_hwmod for iva
_init_omap_device: could not find omap_hwmod for dsp
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The DMM is a piece of interconnect that need to be configured properly
for the tiler functionnality. It thus exposes some configuration registers
that were missing previously.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update the data for GPIO, UART, WD_TIMER and I2C in order to
support the new reset status flag introduce in the following
commit:
commit 2cb068149c
OMAP: hwmod: Fix softreset status check for some new OMAP4 IPs
Without this flag properly set, the reset is done, but the hwmod
core code will not wait for the reset completion to continue its
excecution.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Charulatha V <charu@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The original OMAP4 hwmod data files is fully generated from HW
database. But since the file is introduced incrementaly along
with driver that uses the data, it has to be splitted by the driver
owner and then re-merged by the maintainer.
Because of the similarity of the data, git is completely lost
during such merge and thus the data does not look like the original one
at the end.
Re-order properly the structures to stay in sync with original data set.
This makes it much easier to diff the autogenerated script output with
what's in mainline, see differences, and generate patches for those
diffs. The goal is to stay in sync with the autogenerated data from now
on.
Add a comment that does contain all the IPs that can have a hwmod, but
do not have it in the file for the moment. It gives a good indication
of the progress.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: updated to apply against current core integration branch,
commit message slightly amplified; fixed opt_clks_cnt whitespace]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Cc: Charulatha V <charu@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Otherwise multi-omap1 configurations may set wrong clock speed.
Created and tested against l-o master on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some users were observing crashes during the execution of CORE DVFS
code from OCM RAM -- a locally-modified copy of the linux-omap code.
Richard Woodruff tracked this down to a DTLB miss which had been
inadvertently and intermittently caused by the local modifications.
(The TLB miss caused the ARM MMU to attempt to walk the page tables
stored in SDRAM, which was not possible since SDRAM is off-line for a
portion of the CORE DVFS OCM RAM code.)
Add a note to the OMAP2 & OMAP3 CORE DVFS SRAM code to warn others that
changes may result in crashes here if they are not carefully tested.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Nishanth Menon <nm@ti.com>
