Commit Graph

22 Commits

Author SHA1 Message Date
Ulf Hansson f9a8c3914b ARM: ux500: Enable GPIO regulator for SD-card for HREF boards
Fixes: c94a4ab7af ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-27 09:01:02 +02:00
Ulf Hansson 53d2669844 ARM: ux500: Move GPIO regulator for SD-card into board DTSs
The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but
instead it's specific to the board. Move the definition of it, into the
board DTSs.

Fixes: c94a4ab7af ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-27 09:01:01 +02:00
Ulf Hansson e1a309a4fa ARM: ux500: Add a vmmc regulator through DT for the poped eMMC for href
Add a node in DT for the proper regulator which means we can move away
from the mmci platform data which currently holds the corresponding OCR
mask.

The mmci driver can then calculate the OCR mask based on the voltages
supported by the regulator, instead of relying on the platform data.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-12 12:52:44 +02:00
Ulf Hansson 09585ab450 ARM: ux500: Add the mmc capabilities flags to DT
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-12 12:52:43 +02:00
Ulf Hansson 30cdd668bb ARM: ux500: Convert to the common mmc DT bindings for highspeed mode
The mmci host driver supports the common mmc DT parser, which enables
us to use the use common names instead.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-12 12:52:40 +02:00
Ulf Hansson d63df63a81 ARM: ux500: Add mmci signal directions and feeback clock in DT for href
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-12 12:52:39 +02:00
Linus Walleij 8858d88a25 ARM: ux500: disable msp2 device tree node
Commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.

Fix this up by marking the node disabled again.

Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
2014-02-11 09:21:45 -08:00
Ulf Hansson a987a3accc ARM: ux500: Refactor common DT configs for sdi[n] devices
Remove duplicated configurations and move specific details into
each corresponding dtsi file for the href versions.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-13 10:25:37 +01:00
Linus Walleij 1a780d45b1 ARM: ux500: move GPIO key configuration to device tree
This moves over the configuration of the GPIO keys (used for
proximity sensor and Hall effect sensor) from the static pin
configuration file to the device tree. As part of the exercise,
implement the GPIO keys properly in a per-UIB file as this
setup actually differs with each UIB.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:56 +01:00
Linus Walleij 817a5b967d ARM: ux500: move MCDE pin config to device tree
This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:56 +01:00
Linus Walleij a12f703c5a ARM: ux500: move MUSB pin config to device tree
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 70b41abc15 ARM: ux500: move MSP pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 1e66235330 ARM: ux500: move MMC/SD/SDIO pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 96fee13f0f ARM: ux500: move I2C pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 3bfdebbaeb ARM: ux500: move UART pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.

We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij d62407b0a6 ARM: ux500: move TC35892 at 0x42 to hrefprev60
The TC35892 was mounted as a GPIO expander on the HREF prior
to v60 and not in later versions, which instead use the Nomadik
GPIO directly, so move it over to the hrefprev60 DTS file.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-10-02 16:17:03 +02:00
Linus Walleij 7e9dee0ca2 ARM: ux500: correct I2C address of ambient light sensor
The ambient light sensor is places at address 0x29 nothing else.
This patch makes the ambient light sensor probe again.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-10-02 15:03:03 +02:00
Linus Walleij c90c36e4bc ARM: ux500 enable the AB8500 gpio for all HREFs
The AB8500 GPIO was only registered for the pre-v60 HREF but should
be made available on all HREF variants, move the DT entry to the
common file.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-09-26 15:10:27 +02:00
Linus Walleij 385d61ce26 ARM: ux500: add default trigger on HREF LED
This adds a heartbeat on the first LED on the ux500 HREF
boards.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-09-26 13:01:38 +02:00
Linus Walleij 8cc3168ccd ARM: ux500: delete surplus PRCMU regulator defines
The Ux500 boards are layered like this:
ste-snowball.dts includes ste-href.dtsi that includes
ste-dbx500.dtsi.

The dbx500.dtsi defines the PRCMU SoC regulators so the SoC will
probe and you can use ampersand references where need be.

However the HREF common dtsi and these two boards redefine the
same PRCMU SoC regulators with the very same names and properties
for no reason. This is like filling in the same line three
times instead of drawing it once. Just delete the surplus
references and have the PRCMU regulators defines in the SoC
files ste-dbx500.dtsi, this is enough.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-09-26 11:03:54 +02:00
Linus Walleij 2ce05a14bb ARM: ux500: fix devicetree builds
The patch set beginning with commit:
"ARM: ux500: Apply a ste-* prefix onto snowball.dts"
thru commit:
"ARM: ux500: Remove u9540.dts as it's been replaced"
altered the names of the ux500 device tree files but forgot
to:

- Rename the ccu8540-pinctrl.dtsi file

- Update #include statements from files using these
  files, so the build broke.

- Update the Makefile for the device trees so the build
  broke.

Fix it up so we can build them all again.

Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
2013-08-14 22:32:07 +02:00
Lee Jones 23a8ceb076 ARM: ux500: Apply a ste-* prefix onto href.dtsi
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
2013-08-07 15:33:54 +02:00