Current sh_mobile_sdhi's platform data is set via sh_mobile_sdhi_info
and it is just copied to tmio_mmc_data.
Now, tmio mmc platform data is specified via tmio_mmc_data.
This patch replace sh_mobile_sdhi_info to tmio_mmc_data
struct sh_mobile_sdhi_info { -> struct tmio_mmc_data {
int dma_slave_tx; -> void *chan_priv_tx;
int dma_slave_rx; -> void *chan_priv_rx;
unsigned long tmio_flags; -> unsigned long flags;
unsigned long tmio_caps; -> unsigned long capabilities;
unsigned long tmio_caps2; -> unsigned long capabilities2;
u32 tmio_ocr_mask; -> u32 ocr_mask;
unsigned int cd_gpio; -> unsigned int cd_gpio;
}; unsigned int hclk;
void (*set_pwr)(...);
void (*set_clk_div)(...);
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The information is already included in the COPYING file in the kernel
sources root directory, we don't want to modify all source files when
the FSF will move to a new address, and I'm tired of seeing the related
checkpatch.pl warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move all definitions for legacy INTC from the common "irqs.h" to the
INTC-specific "intc.h".
Include "intc.h" in sh7372/sh73a0 CPU and board files where needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
[horms+renesas@verge.net.au: omitted whitespace change]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As per arch_probe_nr_irqs(), the default value is NR_IRQS, which maps to
NR_IRQS_LEGACY if CONFIG_SPARSE_IRQ=y.
Since SPARSE_IRQ is selected by both ARCH_MULTIPLATFORM and
ARCH_SHMOBILE_LEGACY, it's always enabled on shmobile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Current fsi driver is using SNDRV_DMA_TYPE_CONTINUOUS
for snd_pcm_lib_preallocate_pages_for_all().
But, it came from original dma-sh7760.c,
and no longer needed.
This patch exchange its parameter, and removed
original dma mapping and un-needed
dma_sync_single_xxx() from driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Change location of sh73a0.h so it can be included as "sh73a0.h"
instead of the old style <mach/sh73a0.h>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change location for common.h so it can be used as #include "common.h"
instead of the old style #include <mach/common.h>.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move most of irqs.h so it can be used as #include "irqs.h"
instead of the old style #include <mach/irqs.h>.
Legacy code in drivers/pinctrl needs more work to get rid
of the "mach" portion of the include path, so some part
is left in the original location.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: Do not add trailing blank line to irqs.h]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The cache size should already be present in the L2 cache auxiliary
control register: it is part of the integration process to configure
the hardware IP. Most platforms get this right, yet still many
cargo-cult program, and assume that they always need specifying to
the L2 cache code. Remove them so we can find out which really need
this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we now automatically enable early BRESP in core L2C-310 code when
we detect a Cortex-A9, we don't need platforms/SoCs to set this bit
explicitly. Instead, they should seek to preserve the value of bit 30
in the auxiliary control register.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SND_SOC_DAIFMT_CBx_CFx means "codec" side master/slave mode.
Then, FSI will be master mode if it was SND_SOC_DAIFMT_CBS_CFS.
This patch fixup platform settings too.
Then, it tidyups SND_SOC_DAIFMT_INV settings.
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 4dcfa60071 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MMCIF on sh73a0 doesn't support Command Completion Signal, a platform
parameter has to be added to disable it on kzm9g.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The total number of SoC GPIOs is only used to compute the base GPIO
number of th PCF8575 GPIO extender on the KZM9G board. As GPIO
allocation became fully dynamic with DT, no other SH73A0 board will use
the GPIO_NR macro. Move it to the KZM9G board file.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KZM9G uses an AS3711 PMIC to supply power to the CPU and the LCD backlight.
The PMIC on the board is pre-programmed to supply correct voltages to the
CPU, power supply to the backlight has to be turned on at run-time. The
latter is currently performed by a hard-coded I2C command sequence in the
board file. This patch removes the backlight hack and instead adds an I2C
device to instantiate the AS3711 MFD driver, which will add a regulator
device to dynamically adjust CPU voltages and a backlight device.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The VCCQ MC0 power gate is now controlled by a regulator registered by
the PFC driver. Remove the corresponding function GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These changes are all for board specific files. These used to make up a
large portion of the ARM changes in the past, but as we are generalizing
the support and moving to device tree probing, this has gotten
significantly smaller. The only platform actually adding new code here
at the moment is Renesas shmobile, as they are still busy converting
their code to device tree and have not come far enough to not need it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=2cfP
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes (part 1) from Olof Johansson:
"These changes are all for board specific files. These used to make up
a large portion of the ARM changes in the past, but as we are
generalizing the support and moving to device tree probing, this has
gotten significantly smaller.
The only platform actually adding new code here at the moment is
Renesas shmobile, as they are still busy converting their code to
device tree and have not come far enough to not need it."
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
ARM: msm: USB_MSM_OTG needs USB_PHY
ARM: davinci: da850 evm: fix const qualifier placement
ARM: davinci: da850 board: add remoteproc support
ARM: pxa: move debug uart code
ARM: pxa: select PXA935 on saar & tavorevb
ARM: mmp: add more compatible names in gpio driver
ARM: pxa: move PXA_GPIO_TO_IRQ macro
ARM: pxa: remove cpu_is_xxx in gpio driver
ARM: Kirkwood: update Network Space Mini v2 description
ARM: Kirkwood: DT board setup for CloudBox
ARM: Kirkwood: sort board entries by ASCII-code order
ARM: OMAP: board-4430sdp: Provide regulator to pwm-backlight
ARM: OMAP: zoom: Use pwm stack for lcd and keyboard backlight
ARM: OMAP2+: omap2plus_defconfig: Add support for BMP085 pressure sensor
omap2+: Remove useless Makefile line
omap2+: Remove useless Makefile line
ARM: OMAP: RX-51: add missing regulator supply definitions for lis3lv02d
ARM: OMAP1: fix omap_udc registration
ARM: davinci: use is IS_ENABLED macro
ARM: kirkwood: add MACH_GURUPLUG_DT to defconfig
...
This is yet another driver change, which is split out just because
of its size. As already in 3.9, a lot of changes are going on here,
as the shmobile platform gets converted from its own pin control
API to the generic drivers/pinctrl subsystem.
Based on agreements with Paul Mundt, we are merging the sh-arch-side
changes here as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9DPk
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC pinctrl changes for Renesas from Olof Johansson:
"This is yet another driver change, which is split out just because of
its size. As already in 3.9, a lot of changes are going on here, as
the shmobile platform gets converted from its own pin control API to
the generic drivers/pinctrl subsystem.
Based on agreements with Paul Mundt, we are merging the sh-arch-side
changes here as well"
* tag 'renesas-pinctrl-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (142 commits)
ARM: shmobile: r8a7779: Remove INTC function GPIOs
ARM: shmobile: r8a7779: Remove LBSC function GPIOs
ARM: shmobile: r8a7779: Remove USB function GPIOs
ARM: shmobile: r8a7779: Remove HSPI function GPIOs
ARM: shmobile: r8a7779: Remove SCIF function GPIOs
ARM: shmobile: r8a7779: Remove SDHI and MMCIF function GPIOs
ARM: shmobile: r8a7779: Remove DU function GPIOs
ARM: shmobile: r8a7779: Remove DU1_DOTCLKOUT1 GPIO
ARM: shmobile: r8a7740: Remove SDHI and MMCIF function GPIOs
ARM: shmobile: r8a7740: Remove LCD0 and LCD1 function GPIOs
ARM: shmobile: sh73a0: Remove IrDA function GPIOs
ARM: shmobile: sh73a0: Remove USB function GPIOs
ARM: shmobile: sh73a0: Remove BSC function GPIOs
ARM: shmobile: sh73a0: Remove KEYSC function GPIOs
ARM: shmobile: sh73a0: Remove pull-up function GPIOS
ARM: shmobile: sh73a0: Remove FSI function GPIOs
ARM: shmobile: sh73a0: Remove I2C function GPIOs
ARM: shmobile: sh73a0: Remove SCIFA and SCIFB function GPIOs
ARM: shmobile: sh73a0: Remove LCDC and LCDC2 function GPIOs
ARM: shmobile: sh7372: Remove SDHI and MMCIF function GPIOs
...
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
This patch fixup below sparse errors
CHECK ${RENESAS_USB}/common.c
${RENESAS_USB}/common.c:313:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:322:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:384:17: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:524:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:545:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:574:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/common.c:606:9: error: incompatible types in conditional expression (different base types)
${RENESAS_USB}/mod_gadget.c:233:28: warning: symbol 'req_clear_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:274:28: warning: symbol 'req_set_feature' was not declared. Should it be static?
${RENESAS_USB}/mod_gadget.c:375:28: warning: symbol 'req_get_status' was not declared. Should it be static?
[ balbi@ti.com : added three sparse fixes to mod_gadget.c ]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Both SDHI0 and SDHI2 power supplies on kzm9g can be switched on and off. In
the current version this is not used and the regulators are hard-wired to
"on." This patch switches SDHI0 and SDHI2 to proper fixed-voltage
regulators, using GPIOs to enable and disable them. Both ports shall
now be specifying the MMC_CAP_POWER_OFF_CARD MMC capability. Only SDHI0
has been tested with an SDIO card, since SDHI2 is a microSD slot.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
kzm9g supplies 3.3V to its SDHI0 and SDHI2 interfaces. Specifying 2.8V
prevents some (e.g. certain SDIO) cards from working. This patch fixes the
voltage and removes redundant OCR masks from platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Correct the name of smsc devices used for regulator registration
allowing the regulators to be found and used.
This eliminates the need for CONFIG_REGULATOR_DUMMY
when CONFIG_REGULATOR is set.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the sh73a0 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ31.
This removes quite a bit of special-case code
in intc-sh73a0.c but the number of lines get
replaced with platform device information in
setup-sh73a0.c. The PFC code is also adjusted
to make gpio_to_irq() return the correct
interrupt number.
At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace the GPIO-based SDHI and MMCIF pinmux configuration by pinctrl
mappings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The SH73A0 SoC has sparse GPIO numbers. Declare the pin numbers ranges
in the PFC SoC data and use the pin numbers in the GPIO API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
These updates are all for board specific code, including
* defconfig updates for shmobile, davinci, bcm2835, imx, omap and tegra
* SD/MMC and I2C support on bcm2835 (Raspberry PI)
* minor updates for PXA
* shmobile updates to GPIO usage in board files
* More things in OMAP board files are moved over to device tree probing
* Better support for audio devices on some OMAP platforms
Conflicts include the omap board-apollon.c file that is removed without
a replacement, and conflicting context in the 4430sdp board file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/qBE
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board specific changes from Arnd Bergmann:
"These updates are all for board specific code, including
- defconfig updates for shmobile, davinci, bcm2835, imx, omap and
tegra
- SD/MMC and I2C support on bcm2835 (Raspberry PI)
- minor updates for PXA
- shmobile updates to GPIO usage in board files
- More things in OMAP board files are moved over to device tree
probing
- Better support for audio devices on some OMAP platforms"
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: imx_v4_v5_defconfig: Add VPU support
ARM: imx: configs: enable netfilter support
ARM: OMAP2+: Fix twl section warnings related to omap_twl4030_audio_init
ARM: OMAP2+: omap2plus_defconfig: enable omap1 rtc
RX-51: Register twl4030-madc device
RX-51: Add leds lp5523 names from Maemo 5 2.6.28 kernel
ARM: OMAP2+: AM33XX: omap2plus_defconfig: Add support for few drivers
ARM: OMAP1: nokia770: enable CBUS/Retu
ARM: OMAP2+: omap2plus_defconfig: enable CMA allocator
ARM: OMAP2+: omap2plus_defconfig: enable TFP410 chip support
ARM: OMAP3: igep0020: simplify GPIO LEDs dependencies
ARM: OMAP2+: craneboard: support the TPS65910 PMU
ARM: OMAP2+: craneboard: support NAND device
ARM: OMAP3: cm-t3517: add MMC support
ARM: OMAP2+: Remove apollon board support
ARM: shmobile: armadillo800eva: set clock rates before timer init
ARM: tegra: defconfig updates
ARM: shmobile: mackerel: Use gpio_request_one()
ARM: shmobile: kzm9g: Use gpio_request_one()
ARM: shmobile: bonito: Use gpio_request_one()
...
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUSUyPGCrR//JCVInAQI4YA/+Nb0FaA7qMmTPuJhm7aZNfnwBcGxZ7IZp
s2xByEl3r5zbLKlKGNGE0x7Q7ETHV4y9tohzi9ZduH2b60dMRYgII06CEmDPu6/h
4vBap2oLzfWfs9hwpCIh7N9wNzxSj/R42vlXHhNmspHlw7cFk1yw5EeJ+ocxmZPq
H9lyjAxsGErkZyM/xstNQ1Uvhc8XHAFSUzWrg8hvf6AVVR8hwpIqVzfIizv6Vpk6
ryBoUBHfdTztAOrafK54CdRc7l6kVMomRodKGzMyasnBK3ZfFca3IR7elnxLyEFJ
uPDu5DKOdYrjXC8X2dPM6kYiE41YFuqOV2ahBt9HqRe6liNBLHQ6NAH7f7+jBWSI
eeWe84c2vFaqhAGlci/xm4GaP0ud5ZLudtiVPlDY5tYIADqLygNcx1HIt/5sT7QI
h34LMjc4+/TGVWTVf5yRmIzTrCXZv5YoAak3UWFoM4nVBo/eYVyNLEt5g9YsfjrC
P/GWrXJJvOCB3gAi31pgGYJzZg8K7kTTAh/dgxjqzU4f6nGRm5PBydiJe18/lWkH
qtfNE0RbhxCi3JEBnxW48AIEndVSRbd7jf8upC/s9rPURtFSVXp4APTHVyNUKCip
gojBxcRYtesyG/53nrwdTyiyHx6GocmWnMNZJoDo0UQEkog2dOef+StdC3zhc2Vm
9EttcFqWJ+E=
=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even specify
the driver they use, it can all get configured from the device tree
as we do for normal device drivers. The clocksource changes basically
touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose
their headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=DvgJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
Replace occurences of gpio_request() and gpio_direction_*() by calls to
gpio_request_one().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the lighest possible sleep mode on Cortex-A9 cores: CPU sleep. It is
entered by a simple dsb and wfi instruction via cpu_do_idle(). As just
clocks are stopped there is no need to save or restore any state of the
system.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The machine number is hardcoded to ~0 on DT-enabled machines, making
machine_is_*() always fail when support for more than one machine is
compiled into the kernel. Replace the machine_is_kzm9g() call with
of_machine_is_compatible("renesas,kzm9g").
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
=q7gm
-----END PGP SIGNATURE-----
Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
Current simple-card driver calls asoc_simple_card_dai_init()
if platform had a asoc_simple_card_dai_init pointer.
And, this initialization function works only
when platform has an applicable initial value for each dai settings.
And basically, almost all sound card requires certain initialization.
This means that almost all platform has initialization settings,
and driver do nothing if it doesn't have settings.
And additionally, current simple-card supports sysclk settings but it was
only for codec. In order to abolish deviation between cpu and codec,
and in order to simplify processing,
this patch adds asoc_simple_dai, and removed pointless
struct asoc_simple_dai_init_info which was trigger of
calling asoc_simple_card_dai_init().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we have GIC moved to drivers/irqchip and all GIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Now that the GIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=sgYz
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch contains a set of various board updates for ARM platforms.
A few shmobile platforms that are stale have been removed, some
defconfig updates for various boards selecting new features such as
pinctrl subsystem support, and various updates enabling peripherals,
etc."
Fix up conflicts mostly as per Olof.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
ARM: S3C64XX: Add dummy supplies for Glenfarclas LDOs
ARM: S3C64XX: Add registration of WM2200 Bells device on Cragganmore
ARM: kirkwood: Add Plat'Home OpenBlocks A6 support
ARM: Dove: update defconfig
ARM: Kirkwood: update defconfig for new boards
arm: orion5x: add DT related options in defconfig
arm: orion5x: convert 'LaCie Ethernet Disk mini v2' to Device Tree
arm: orion5x: basic Device Tree support
arm: orion5x: mechanical defconfig update
ARM: kirkwood: Add support for the MPL CEC4
arm: kirkwood: add support for ZyXEL NSA310
ARM: Kirkwood: new board USI Topkick
ARM: kirkwood: use gpio-fan DT binding on lsxl
ARM: Kirkwood: add Netspace boards to defconfig
ARM: kirkwood: DT board setup for Network Space Mini v2
ARM: kirkwood: DT board setup for Network Space Lite v2
ARM: kirkwood: DT board setup for Network Space v2 and parents
leds: leds-ns2: add device tree binding
ARM: Kirkwood: Enable the second I2C bus
ARM: mmp: select pinctrl driver
...
6e20a0a429
(gpio: pcf857x: enable gpio_to_irq() support)
added gpio_to_irq() support on pcf857x driver,
but it used pdata->irq.
This patch modifies driver to use client->irq instead of it.
It modifies kzm9g board platform settings,
and device probe information too.
This patch is tested on kzm9g board
Reported-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kuninori Morimoto
Laurent Pinchart
Arnd Bergmann
Geert Uytterhoeven
Linus Torvalds
Magnus Damm
Russell King
Guennadi Liakhovetski
Robin Holt
Simon Horman
Magnus Damm
Bastian Hecht
Olof Johansson
Rob Herring
Stephen Warren